T-1 (3mm) SOLID STATE LAMP Part Number: WP710A10SEC/J3 Hyper Red Features Description z Low power consumption. The Hyper Red device is based on light emitting diode chip z Popular T-1 diameter package. made from AlGaInP. z General purpose leads. z Reliable and rugged. z Long life - solid state reliability. z Available on tape and reel. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050 Selection Guide Part No. Dice WP710A10SEC/J3 Lens Type Hyper Red (AlGaInP) Water Clear Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 2300 4100 *1300 *2400 21/2 34 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Device Typ. peak Peak Wavelength Hyper Red D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 640 nm IF=20mA Hyper Red 625 nm IF=20mA Spectral Line Half-width Hyper Red 25 nm IF=20mA C Capacitance Hyper Red 27 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25C Parameter Hyper Red Units Power dissipation 84 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating/Storage Temperature -40C To +85C Lead Solder Temperature [2] 260C For 3 Seconds Lead Solder Temperature [3] 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050 Hyper Red WP710A10SEC/J3 SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050 PACKING & LABEL SPECIFICATIONS WP710A10SEC/J3 SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050 SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050 All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0539 REV NO: V.4A DATE: MAR/20/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1101029050