LM5045SQ/NOPB - NATIONAL SEMICONDUCTOR

LM5045

LM5045 Full-Bridge PWM Controller with Integrated MOSFET Drivers

Literature Number: SNVS699E

LM5045

October 13, 2011

Full-Bridge PWM Controller with Integrated MOSFET

Drivers

General Description

The LM5045 PWM controller contains all of the features nec-

essary to implement Full-Bridge topology power converters

using either current mode or voltage mode control. This de-

vice is intended to operate on the primary side of an isolated

dc-dc converter with input voltage up to 100V. This highly in-

tegrated controller-driver provides dual 2A high and low side

gate drivers for the four external brige MOSFETs plus control

signals for the secondary side synchronous rectifier MOS-

FETs. External resistors program the leading and trailing

edge dead-time between the main and synchronous rectifier

control signals. Intelligent startup of the synchronous recti-

fiers allows monotonic turn-on of the power converter even

with pre-bias load conditions. Additional features include cy-

cle-by-cycle current limiting, hiccup mode restart, pro-

grammable soft-start, synchronous rectifier soft-start and a 2

MHz capable oscillator with synchronization capability and

thermal shutdown.

Features

■Highest Integration Controller for Small Form Factor, High

Density Power Converters

■High Voltage Start-up Regulator

■Intelligent Sync Rectifier Start-up Allows Linear Turn-on

into Pre-biased Loads

■Synchronous Rectifiers Disabled in UVLO mode and

Hiccup Mode

■Two Independent, Programmable Synchronous Rectifier

dead-time Adjustments

■Four High Current 2A Bridge Gate Drivers

■Wide-Bandwidth Opto-coupler Interface

■Configurable for either Current Mode or Voltage Mode

Control

■Dual-mode Over-Current Protection

■Resistor Programmed 2MHz Oscillator

■Programmable Line UVLO and OVP

Packages

■eTSSOP-28

■LLP-28 (5mm x 5mm)

Simplified Full-Bridge Power Converter

30145401

LM5045 Full-Bridge PWM Controller with Integrated MOSFET Drivers

Connection Diagrams

Top View

30145402

TSSOP28

www.national.com 2

LM5045

Top View

30145403

LLP-28 Package

Ordering Information

Order Number Package Type NSC Package Drawing Supplied As

LM5045MH eTSSOP-28 MXA28A Rail of 48 Units

LM5045MHX eTSSOP-28 MXA28A Tape and Reel of 2500 Units

LM5045SQ LLP-28 SQA28A Available Soon

LM5045SQX LLP-28 SQA28A Available Soon

Pin Descriptions

TSSOP

Pin LLP Pin Name Description Application Information

1 25 UVLO Line Under-Voltage Lockout An external voltage divider from the power source sets the

shutdown and standby comparator levels. When UVLO reaches

the 0.4V threshold the VCC and REF regulators are enabled. At

the 1.25V threshold, the SS pin is released and the controller

enters the active mode. Hysteresis is set by an internal current

sink that pulls 20µA from the external resistor divider.

2 26 OVP/OTP Over Voltage Protection An external voltage divider from the input power supply sets the

shutdown level during an over-voltage condition. Alternatively, an

external NTC thermistor voltage divider can be used to set the

shutdown temperature. The threshold is 1.25V. Hysteresis is set

by an internal current that sources 20 µA of current into the

external resistor divider.

3 www.national.com

LM5045

TSSOP

Pin LLP Pin Name Description Application Information

3 27 RAMP Input to PWM Comparator Modulation ramp for the PWM comparator. This ramp can be a

signal representative of the primary current (current mode) or

proportional to the input voltage (feed-forward voltage mode).

This pin is reset to GND at the end of every cycle.

4 28 CS Current Sense Input If CS exceeds 750mV the PWM output pulse will be terminated,

entering cycle-by-cycle current limit. An internal switch holds CS

low for 40nS after either output switches high to blank leading

edge transients.

5 1 SLOPE Slope Compensation Current A ramping current source from 0 to 100µA is provided for slope

compensation in current mode control. This pin can be connected

through an appropriate resistor to the CS pin to provide slope

compensation. If slope compensation is not required, SLOPE

must be tied to ground.

6 2 COMP Input to the Pulse Width Modulator An external opto-coupler connected to the COMP pin sources

current into an internal NPN current mirror. The PWM duty cycle

is at maximum with zero input current, while 1mA reduces the

duty cycle to zero. The current mirror improves the frequency

response by reducing the AC voltage across the opto-coupler.

7 3 REF Output of a 5V reference Maximum output current is 15mA. Locally decouple with a 0.1µF

capacitor.

8 4 RT/SYNC Oscillator Frequency Control and

Frequency Synchronization

The resistance connected between RT and AGND sets the

oscillator frequency. Synchronization is achieved by AC coupling

a pulse to the RT/SYNC pin that raises the voltage at least 1.5V

above the 2V nominal bias level.

9 5 AGND Analog Ground Connect directly to the Power Ground.

10 6 RD1 Synchronous Rectifier Leading

Edge Delay

The resistance connected between RD1 and AGND sets the

delay from the falling edge of SR1 or SR2 and the rising edge of

HO2/LO1 or HO1/LO2 respectively.

11 7 RD2 Synchronous Rectifier Trailing

Edge Delay

The resistance connected between RD2 and AGND sets the

delay from the falling edge of HO1/LO2 or HO2/LO1 and the rising

edge of SR2 or SR1 respectively.

12 8 RES Restart Timer Whenever the CS pin exceeds the 750mV cycle-cycle current

limit threshold, 30µA current is sourced into the RES capacitor for

the remainder of the PWM cycle. If the RES capacitor voltage

reaches 1.0V, the SS capacitor is discharged to disable the HO1,

HO2, LO1, LO2 and SR1, SR2 outputs. The SS pin is held low

until the voltage on the RES capacitor has been ramped between

2V and 4V eight times by 10µA charge and 5µA discharge

currents. After the delay sequence, the SS capacitor is released

to initiate a normal start-up sequence.

13 9 SS Soft-Start Input An internal 20µA current source charges the SS pin during start-

up. The input to the PWM comparator gradually rises as the SS

capacitor charges to steadily increase the PWM duty cycle.

Pulling the SS pin to a voltage below 200mV stops PWM pulses

at HO1,2 and LO1,2 and turns off the synchronous rectifier FETs

to a low state.

14 10 SSSR Secondary Side Soft-Start An external capacitor and an internal 20µA current source set the

soft-start ramp for the synchronous rectifiers. The SSSR

capacitor charge-up is enabled after the first output pulse and

SS>2V and Icomp <800µA

15 11 SSOFF Soft-Stop Disable When SS OFF pin is connected to the AGND, the LM5045 soft-

stops in the event of a VIN UVLO and Hiccup mode current limit

condition. If the SSOFF pin is connected to REF pin, the controller

hard-stops on any fault condition. Refer Table 1 for more details.

www.national.com 4

LM5045

TSSOP

Pin LLP Pin Name Description Application Information

19 15 SR2 Synchronous Rectifier Driver Control output for synchronous rectifier gate. Capable of peak

sourcing 100mA and sinking 400mA.

21 17 VCC Output of Start-Up Regulator The output voltage of the start-up regulator is initially regulated to

9.5V. Once the secondary side soft-start (SSSR pin) reaches 1V,

the VCC output is reduced to 7.7V. If an auxiliary winding raises

the voltage on this pin above the regulation set-point, the internal

start-up regulator will shutdown, thus reducing the IC power

dissipation.

22 18 PGND Power Ground Connect directly to Analog Ground

23, 20 19, 16 LO1, LO2 Low Side Output Driver Alternating output of the PWM gate driver. Capable of 1.5A peak

source and 2A peak sink current.

24 20 SR1 Synchronous Rectifier Driver Control output for synchronous rectifier gate. Capable of peak

sourcing 100mA and sinking 400mA.

25, 18 21, 14 BST1,2 Gate Drive Bootstrap Bootstrap capacitors connected between BST1,2 and SW1,2

provide bias supply for the high side HO1,2 gate drivers. External

diodes are required between VCC and BST1,2 to charge the

bootstrap capacitors when SW1,2 are low.

26, 17 22, 13 HO1,2 High Side Output Driver High side PWM outputs capable of driving the upper MOSFET of

the bridge with 1.5A peak source and 2A peak sink current.

27, 16 23, 12 HS1,2 Switch Node Common connection of the high side FET source, low side FET

drain and transformer primary winding.

28 24 VIN Input Power Source Input to the Start-up Regulator. Operating input range is 14V to

100V. For power sources outside of this range, the LM5045 can

be biased directly at VCC by an external regulator.

5 www.national.com

LM5045

Absolute Maximum Ratings (Note 1)

VIN to GND -0.3V to 105V

HS to GND(Note 4) -5V to 105V

BST1/BST2 to GND -0.3V to 116V

BST1/BST2 to HS1/HS2 -0.3V to 16V

HO1/HO2 to HS1/HS2(Note 2) -0.3V to BST1/

BST2+0.3V

LO1/LO2/SR1/SR2(Note 2) -0.3V to VCC+0.3V

VCC to GND -0.3V to 16V

REF,SSOFF,RT,OVP,UVLO to GND -0.3V to 7V

RAMP -0.3V to 7V

COMP -0.3V

COMP Input Current +10mA

All other inputs to GND(Note 2) -0.3 to REF+0.3V

ESD Rating HBM(Note 3) 2 kV

Storage Temperature Range -55°C to 150°C

Junction Temperature 150°C

Operating Ratings (Note 1)

VIN Voltage 14V to 100V

External Voltage Applied to VCC 10V to 14V

Junction Temperature -40°C to +125°C

SLOPE -0.3V to 2V

Electrical Characteristics Limits in standard typeface are for TJ = 25°C only; limits in boldface type apply the

junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, RT =

25kΩ, RD1=RD2=20kΩ. No load on HO1, HO2, LO1, LO2, SR1, SR2, COMP=0V, UVLO=2.5V, OVP=0V, SSOFF=0V.

Symbol Parameter Conditions Min Typ Max Units

Startup Regulator (VCC pin)

VCC1 VCC voltage ICC= 10mA (SSSR<1V) 9.3 9.6 9.9 V

VCC2 VCC voltage ICC= 10mA (SSSR>1V) 7.5 7.8 8.1 V

ICC(Lim) VCC current limit VCC= 6V 52 70 mA

ICC(ext) VCC supply current Supply current into VCC from an externally

applied source. VCC = 10V

4.6 mA

VCC load regulation ICC from 0 to 50 mA 35 mV

VCC(UV) VCC under-voltage threshold Positive going VCC VCC1–

0.2

VCC1–

0.1

VCC under-voltage threshold Negative going VCC 5.9 6.3 6.7 V

IIN VIN operating current 4 mA

VIN shutdown current VIN=20V, VUVLO=0V 300 520 µA

VVIN=100V, VUVLO=0V 350 550 µA

VIN start-up regulator leakage VCC=10V 160 µA

Voltage Reference Regulator (REF pin)

VREF REF Voltage IREF = 0mA 4.85 55.15 V

REF voltage regulation IREF = 0 to 10mA 25 50 mV

IREF(Lim) REF current limit VREF = 4.5V 15 20 mA

VREFUV VREF under-voltage threshold Positive going VREF 4.3 4.5 4.7 V

Hysteresis 0.25 V

Under-Voltage Lock Out and shutdown (UVLO pin)

VUVLO Under-voltage threshold 1.18 1.25 1.32 V

IUVLO Hysteresis current UVLO pin sinking current when

VUVLO<1.25V

16 20 24 µA

Under-voltage standby enable

threshold

UVLO voltage rising 0.32 0.4 0.48 V

Hysteresis 0.05 V

VOVP OVP shutdown threshold OVP rising 1.18 1.25 1.32 V

OVP hysteresis current OVP sources current when OVP>1.25V 16 20 24 µA

Soft-Start (SS Pin)

ISS SS charge current VSS = 0V 16 20 24 µA

SS threshold for SSSR charge

current enable

ICOMP<800µA 1.93 2.0 2.20 V

SS output low voltage Sinking 100µA 40 mV

SS threshold to disable switching 200 mV

www.national.com 6

LM5045

Symbol Parameter Conditions Min Typ Max Units

ISSSR SSSR charge current VSS>2V, ICOMP<800µA 16 20 24 µA

ISSSR-DIS1 SSSR discharge current 1 VUVLO<1.25V 54 65 75 µA

ISSSR-DIS2 SSSR discharge current 2 VRES>1V 109 125 147 µA

SSSR output low voltage Sinking 100µA 50 mV

SSSR threshold to enable SR1/SR2 1.2 V

Current Sense Input (CS Pin)

VCS Current limit threshold 0.710 0.750 0.785 V

CS delay to output 65 ns

CS leading edge blanking 50 ns

RCS CS sink impedance (clocked) Internal FET sink impedance 18 45 Ω

Soft-Stop Disable (SS OFF Pin)

VIH(min) SSOFF Input-threshold 2.8 V

SSOFF pull down resistance 200 kΩ

Current Limit Restart (RES Pin)

RRES RES pull-down resistance Termination of hiccup timer 37 Ω

VRES RES hiccup threshold 1 V

RES upper counter threshold 4 V

RES lower counter threshold 2 V

IRES-SRC1 Charge current source 1 VRES<1V,VCS>750mV 30 µA

IRES-SRC2 Charge current source 2 1V<VRES<4V 10 µA

IRES-DIS2 Discharge current source 1 VCS<750mV 5 µA

IRES-DIS2 Discharge current source 2 2V<VRES<4V 5 µA

Ratio of time in hiccup mode to time

in current limit

VRES>1V, Hiccup counter 147

Voltage Feed-Forward (RAMP Pin)

RAMP sink impedance (Clocked) 5.5 20 Ω

Oscillator (RT Pin)

FSW1 Frequency (LO1, half oscillator

frequency)

RT = 25 kΩ185 200 215 kHz

FSW2 Frequency (LO1, half oscillator

frequency)

RT = 10 kΩ420 480 540 kHz

DC level 2.0 V

RT sync threshold 2.8 33.3 V

Synchronous Rectifier Timing Control (RD1 & RD2 Pins)

T1 SR trailing edge delay

SR turn-off to HO&LO both on

RD1=20 kΩ45 65 90 ns

RD1=100 kΩ232 300 388 ns

T2 SR leading edge

HO or LO turn-off to SR turn-on

RD2=20 kΩ43 65 90 ns

RD2=100 kΩ227 300 384 ns

7 www.national.com

LM5045

Symbol Parameter Conditions Min Typ Max Units

Comp Pin

VPWM-OS COMP current to RAMP offset VRAMP=0V 680 800 940 µA

VSS-OS SS to RAMP offset VRAMP=0V 0.78 1.0 1.22 V

COMP current to RAMP gain ΔRAMP/ΔICOMP 2400 Ω

SS to RAMP gain ΔSS/ΔRAMP 0.5

COMP current for SSSR charge

current enable

VSS > 2V 690 800 915 µA

COMP to output delay 120 ns

Minimum duty cycle ICOMP = 1mA 0%

Slope Compensation (SLOPE Pin)

ISLOPE Slope compensation current ramp Peak of RAMP current 100 µA

BOOST (BST Pin)

VBst uv BST under-voltage threshold VBST-VHS rising 3.8 4.7 5.6 V

Hysteresis 0.5 V

HO1, HO2, LO1, LO2 Gate Drivers

VOL Low-state output voltage IHO/LO = 100mA 0.16 0.32 V

VOH High-state output voltage IHO/LO = 100mA

VOHL = VCC-VLO

VOHH = VBST-VHO

0.27 0.495 V

Rise Time C-load = 1000pF 16 ns

Fall Time C-load = 1000pF 11 ns

IOHL Peak Source Current VHO/LO = 0V 1.5 - A

IOLL Peak Sink Current VHO/LO = VCC 2 - A

SR1, SR2 Gate Drivers

VOL Low-state output voltage ISR1/SR2 = 10mA 0.05 0.1 V

VOH High-state output voltage ISR1/SR2 = 10mA,

VOH = VREF-VSR

0.17 0.28 V

Rise Time C-load = 1000pF 60 ns

Fall Time C-load = 1000pF 20 ns

IOHL Peak Source Current VSR = 0V 0.1 - A

IOLL Peak Sink Current VSR = VREF 0.4 - A

Thermal

TSD Thermal Shutdown Temp 160 °C

Thermal Shutdown Hysteresis 25 °C

RJA Junction to Ambient(Note 5) eTSSOP - 28/LLP-28 40 °C/W

RJC Junction to Case 4 °C/W

Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the

device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics.

Note 2: These pins are output pins and as such should not be connected to an external voltage source. The voltage range listed is the limits the internal circuitry

is designed to reliably tolerate in the application circuit.

Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.

Note 4: The negative HS voltage must never be more negative than VCC-16V. For example, if VCC=12V, the negative transients at HS must not exceed -4V.

Note 5: 4 layer standard thermal test board. Cu thickness of layers (2oz, 1oz, 1oz, 2oz).

www.national.com 8

LM5045

Typical Performance Characteristics

Application Board Efficiency

5 10 15 20 25 30

100

EFFICIENCY (%)

LOAD CURRENT (A)

36V

48V

72V

VOUT = 3.3V

30145452

VCC vs ICC

30145459

VVCC and VREF vs. VVIN

30145455

IIN vs. VIN

0 20 40 60 80 100

I IN (V)

V IN (V)

VUVLO=3V

VUVLO=1V

VUVLO=0V

30145460

VREF vs. IREF

30145409

Oscillator Frequency vs. RT

30145456

9 www.national.com

LM5045

Dead-Time T1, T2 vs. RD1, RD2

30145457

Dead-Time T1, T2 vs. Temperature

-50 0 50 100 150

DEAD-TIME T1,T2 (ns)

TEMPERATURE(°C)

30145454

CS Threshold vs. Temperature

30145413

www.national.com 10

LM5045

Block Diagram

30145404

FIGURE 1.

11 www.national.com

LM5045

Functional Description

The LM5045 PWM controller contains all of the features nec-

essary to implement a Full-Bridge topology power converter

using either current mode or voltage mode control. This de-

vice is intended to operate on the primary side of an isolated

dc-dc converter with input voltage up to 100V. This highly in-

tegrated controller-driver provides dual 2A high and low side

gate drivers for the four external bridge MOSFETs plus con-

trol signals for secondary side synchronous rectifiers. Exter-

nal resistors program the leading and trailing edge dead-time

between the main and synchronous rectifier control signals.

Intelligent startup of synchronous rectifier allows turn-on of

the power converter into the pre-bias loads. Cycle-by-cycle

current limit protects the power components from load tran-

sients while hiccup mode protection limits average power

dissipation during extended overload conditions. Additional

features include programmable soft-start, soft-start of the

synchronous rectifiers, and a 2 MHz capable oscillator with

synchronization capability and thermal shutdown.

High-Voltage Start-Up Regulator

The LM5045 contains an internal high voltage start-up regu-

lator that allows the input pin (VIN) to be connected directly

to the supply voltage over a wide range from 14V to 100V.

The input can withstand transients up to 105V. When the UV-

LO pin potential is greater than 0.4V, the VCC regulator is

enabled to charge an external capacitor connected to the

VCC pin. The VCC regulator provides power to the voltage

reference (REF) and the gate drivers (HO1/HO2 and LO1/

LO2). When the voltage on the VCC pin exceeds its Under

Voltage (UV) threshold, the internal voltage reference (REF)

reaches its regulation set point of 5V and the UVLO voltage

is greater than 1.25V, the soft-start capacitor is released and

normal operation begins. The regulator output at VCC is in-

ternally current limited. The value of the VCC capacitor de-

pends on the total system design, and its start-up character-

istics. The recommended range of values for the VCC

capacitor is 0.47μF to 10µF.

The internal power dissipation of the LM5045 can be reduced

by powering VCC from an external supply. The output voltage

of the VCC regulator is initially regulated to 9.5V. After the

synchronous rectifiers are engaged (which is approximately

when the output voltage in within regulation), the VCC voltage

is reduced to 7.7V. In typical applications, an auxiliary trans-

former winding is connected through a diode to the VCC pin.

This winding must raise the VCC voltage above 8V to shut off

the internal start-up regulator. Powering VCC from an auxil-

iary winding improves efficiency while reducing the

controller’s power dissipation. The VCC UV circuit will still

function in this mode, requiring that VCC never falls below its

UV threshold during the start-up sequence. The VCC regula-

tor series pass transistor includes a diode between VCC and

VIN that should not be forward biased in normal operation.

Therefore, the auxiliary VCC voltage should never exceed the

VIN voltage.

An external DC bias voltage can be used instead of the inter-

nal regulator by connecting the external bias voltage to both

the VCC and the VIN pins. This implementation is shown in

the Applications Information section. The external bias must

be greater than 10V and less than the VCC maximum voltage

rating of 14V.

Line Under-Voltage Detector

The LM5045 contains a dual level Under-Voltage Lockout

(UVLO) circuit. When the UVLO pin voltage is below 0.4V, the

controller is in a low current shutdown mode. When the UVLO

pin voltage is greater than 0.4V but less than 1.25V, the con-

troller is in standby mode. In standby mode the VCC and REF

bias regulators are active while the controller outputs are dis-

abled. When the VCC and REF outputs exceed their respec-

tive under-voltage thresholds and the UVLO pin voltage is

greater than 1.25V, the soft-start capacitor is released and the

normal operation begins. An external set-point voltage divider

from VIN to GND can be used to set the minimum operating

voltage of the converter. The divider must be designed such

that the voltage at the UVLO pin will be greater than 1.25V

when VIN enters the desired operating range. UVLO hystere-

sis is accomplished with an internal 20μA current sink that is

switched on or off into the impedance of the set-point divider.

When the UVLO threshold is exceeded, the current sink is

deactivated to quickly raise the voltage at the UVLO pin.

When the UVLO pin voltage falls below the 1.25V threshold,

the current sink is enabled causing the voltage at the UVLO

pin to quickly fall. The hysteresis of the 0.4V shutdown com-

parator is internally fixed at 50mV.

The UVLO pin can also be used to implement various remote

enable / disable functions. Turning off the converter by forcing

the UVLO pin to standby condition (0.4V < UVLO < 1.25V)

provides a controlled soft-stop. Refer to the Soft Stop section

for more details.

Over Voltage Protection

An external voltage divider can be used to set either an over

voltage or an over temperature protection. During an OVP

condition, the SS and SSSR capacitors are discharged and

all the outputs are disabled. The divider must be designed

such that the voltage at the OVP pin is greater than 1.25V

when over voltage/temperature condition exists. Hysteresis is

accomplished with an internal 20μA current source. When the

OVP pin voltage exceeds 1.25V, the 20μA current source is

activated to quickly raise the voltage at the OVP pin. When

the OVP pin voltage falls below the 1.25V threshold, the cur-

rent source is deactivated causing the voltage at the OVP to

quickly fall. Refer to the Applications Information section for

more details.

Reference

The REF pin is the output of a 5V linear regulator that can be

used to bias an opto-coupler transistor and external house-

keeping circuits. The regulator output is internally current

limited to 15mA. The REF pin needs to be locally decoupled

with a ceramic capacitor, the recommended range of values

are from 0.1μF to 10μF

Oscillator, Sync Input

The LM5045 oscillator frequency is set by a resistor connect-

ed between the RT pin and AGND. The RT resistor should be

located very close to the device. To set a desired oscillator

frequency (FOSC), the necessary value of RT resistor can be

calculated from the following equation:

For example, if the desired oscillator frequency is 400 kHz i.e.

each phase (LO1 or LO2) at 200 kHz, the value of RT will be

25kΩ. If the LM5045 is to be synchronized to an external

clock, that signal must be coupled into the RT pin through a

100pF capacitor. The RT pin voltage is nominally regulated

www.national.com 12

LM5045

at 2.0V and the external pulse amplitude should lift the pin to

between 3.5V and 5.0V on the low-to-high transition. The

synchronization pulse width should be between 15 and

200ns. The RT resistor is always required, whether the oscil-

lator is free running or externally synchronized and the SYNC

frequency must be equal to, or greater than the frequency set

by the RT resistor. When syncing to an external clock, it is

recommended to add slope compensation by connecting an

appropriate resistor from the VCC pin to the CS pin. Also dis-

able the SLOPE pin by grounding it.

Cycle-by-Cycle Current Limit

The CS pin is to be driven by a signal representative of the

transformer’s primary current. If the voltage on the CS pin ex-

ceeds 0.75V, the current sense comparator immediately ter-

minates the PWM cycle. A small RC filter connected to the

CS pin and located near the controller is recommended to

suppress noise. An internal 18Ω MOSFET discharges the ex-

ternal current sense filter capacitor at the conclusion of every

cycle. The discharge MOSFET remains on for an additional

40ns after the start of a new PWM cycle to blank leading edge

spikes. The current sense comparator is very fast and may

respond to short duration noise pulses. Layout is critical for

the current sense filter and the sense resistor. The capacitor

associated with CS filter must be placed very close to the de-

vice and connected directly to the CS and AGND pins. If a

current sense transformer is used, both the leads of the trans-

former secondary should be routed to the filter network, which

should be located close to the IC. When designing with a cur-

rent sense resistor, all of the noise sensitive low power ground

connections should be connected together near the AGND

pin, and a single connection should be made to the power

ground (sense resistor ground point).

Hiccup Mode

The LM5045 provides a current limit restart timer to disable

the controller outputs and force a delayed restart (i.e. Hiccup

mode) if a current limit condition is repeatedly sensed. The

number of cycle-by-cycle current limit events required to trig-

ger the restart is programmed by the external capacitor at the

RES pin. During each PWM cycle, the LM5045 either sources

or sinks current from the RES capacitor. If current limit is de-

tected, the 5μA current sink is disabled and a 30μA current

source is enabled. If the RES voltage reaches the 1.0V

threshold, the following restart sequence occurs, as shown in

Figure 2:

•The SS and SSSR capacitors are fully discharged

•The 30μA current source is turned-off and the 10μA

current source is turned-on.

•Once the voltage at the RES pin reaches 4.0V the 10μA

current source is turned-off and a 5μA current sink is

turned-on, ramping the voltage on the RES capacitor

down to 2.0V.

•Once RES capacitor reaches 2.0V, threshold, the 10μA

current source is turned-on again. The RES capacitor

voltage is ramped between 4.0V and 2.0V eight times.

•When the counter reaches eight, the RES pin voltage is

pulled low and the soft-start capacitor is released to begin

a soft-start sequence. The SS capacitor voltage slowly

increases. When the SS voltage reaches 1.0V, the PWM

comparator will produce the first narrow pulse.

•If the overload condition persists after restart, cycle-by-

cycle current limiting will begin to increase the voltage on

the RES capacitor again, repeating the hiccup mode

sequence.

•If the overload condition no longer exists after restart, the

RES pin will be held at ground by the 5μA current sink and

the normal operation resumes.

The hiccup mode function can be completely disabled by

connecting the RES pin to the AGND pin. In this configuration

the cycle-by-cycle protection will limit the maximum output

current indefinitely, no hiccup restart sequences will occur.

30145416

FIGURE 2. Hiccup Mode Delay and Soft-Start Timing Diagram

13 www.national.com

LM5045

PWM Comparator

The LM5045 pulse width modulator (PWM) comparator is a

three input device, it compares the signal at the RAMP pin to

the loop error signal or the soft-start, whichever is lower, to

control the duty cycle. This comparator is optimized for speed

in order to achieve minimum controllable duty cycles. The

loop error signal is received from the external feedback and

isolation circuit in the form of a control current into the COMP

pin. The COMP pin current is internally mirrored by a match-

ing pair of NPN transistors which sink current through a 5kΩ

resistor connected to the 5V reference. The resulting control

voltage passes through a 1V offset, followed by a 2:1 resistor

divider before being applied to the PWM comparator.

An opto-coupler detector can be connected between the REF

pin and the COMP pin. Because the COMP pin is controlled

by a current input, the potential difference across the opto-

coupler detector is nearly constant. The bandwidth limiting

phase delay which is normally introduced by the significant

capacitance of the opto-coupler is thereby greatly reduced.

Higher loop bandwidths can be realized since the bandwidth

limiting pole associated with the opto-coupler is now at a

much higher frequency. The PWM comparator polarity is con-

figured such that with no current flowing into the COMP pin,

the controller produces maximum duty cycle.

RAMP Pin

The voltage at the RAMP pin provides the modulation ramp

for the PWM comparator. The PWM comparator compares

the modulation ramp signal at the RAMP pin to the loop error

signal to control the duty cycle. The modulation ramp signal

can be implemented either as a ramp proportional to the input

voltage, known as feed-forward voltage mode control, or as

a ramp proportional to the primary current, known as current

mode control. The RAMP pin is reset by an internal MOSFET

with an RDS(ON) of 5.5Ω at the conclusion of each PWM cycle.

The ability to configure the RAMP pin for either voltage mode

or current mode allows the controller to be implemented for

the optimum control method depending upon the design con-

straints. Refer to the Applications Information section for more

details on configuring the RAMP pin for feed-forward voltage

mode control and peak current mode control.

Slope Pin

For duty cycles greater than 50% (25% for each phase), peak

current mode control is subject to sub-harmonic oscillation.

Sub-harmonic oscillation is normally characterized by observ-

ing alternating wide and narrow duty cycles. This can be

eliminated by adding an artificial ramp, known as slope com-

pensation, to the modulating signal at the RAMP pin. The

SLOPE pin provides a current source ramping from 0 to

100μA, at the frequency set by the RT resistor, for slope com-

pensation. The ramping current source at the SLOPE pin can

be utilized in a couple of different ways to add slope compen-

sation to the RAMP signal:

1) As shown in Figure 3(a), the SLOPE and RAMP pins can

be connected together through an appropriate resistor to the

CS pin. This configuration will inject current sense signal plus

slope compensation to the RAMP pin but CS pin will not see

any slope compensation. Therefore, in this scheme slope

compensation will not affect the current limit.

2) In a second configuration, as shown in Figure 3(b), the

SLOPE, RAMP and CS pins can be tied together. In this con-

figuration the ramping current source from the SLOPE pin will

flow through the filter resistor and filter capacitor, therefore

both the CS pin and the RAMP pin will see the current sense

signal plus the slope compensation ramp. In this scheme, the

current limit is compensated by the slope compensation and

the current limit onset point will vary.

If the slope compensation is not required for e.g. in feed-for-

ward voltage mode control, the SLOPE pin must be connect-

ed to the AGND pin. When the RT pin is synched to an

external clock, it is recommended to disable the SLOPE pin

and add slope compensation externally by connecting an ap-

propriate resistor from the VCC pin to the CS pin. Please refer

to the Applications Information section for more details.

30145451

FIGURE 3. Slope Compensation Configuration

a) Slope Compensation Configured for PWM Only (No Current Limit Slope)

b) Slope Compensation Configured for PWM and Current Limit

www.national.com 14

LM5045

Soft-Start

The soft-start circuit allows the power converter to gradually

reach a steady state operating point, thereby reducing the

start-up stresses and current surges. When bias is supplied

to the LM5045, the SS capacitor is discharged by an internal

MOSFET. When the UVLO, VCC and REF pins reach their

operating thresholds, the SS capacitor is released and is

charged with a 20µA current source. Once the SS pin voltage

crosses the 1V offset, SS controls the duty cycle. The PWM

comparator is a three input device; it compares the RAMP

signal against the lower of the signals between the soft-start

and the loop error signal. In a typical isolated application, as

the secondary bias is established, the error amplifier on the

secondary side soft-starts and establishes closed- loop con-

trol, steering the control away from the SS pin.

One method to shutdown the regulator is to ground the SS

pin. This forces the internal PWM control signal to ground,

reducing the output duty cycle quickly to zero. Releasing the

SS pin begins a soft-start cycle and normal operation re-

sumes. A second shutdown method is presented in the UVLO

section.

Gate Driver Outputs

The LM5045 provides four gate drivers: two floating high side

gate drivers HO1 and HO2 and two ground referenced low

side gate drivers LO1 and LO2. Each internal driver is capable

of source 1.5A peak and sinking 2A peak. Initially, the diago-

nal HO1 and LO2 are turned-on together, followed by an off-

time when all the four gate driver outputs are off. In the

subsequent phase the diagonal HO2 and LO1 are turned on

together followed by an off-time. The low-side gate drivers are

powered directly by the VCC regulator. The HO1 and HO2

gate drivers are powered from a bootstrap capacitor connect-

ed between BST1/BST2 and HS1/HS2 respectively. An ex-

ternal diode connected between VCC (anode pin) and BST

(cathode pin) provides the high side gate driver power by

charging the bootstrap capacitor from VCC when the corre-

sponding switch node (HS1/HS2 pin) is low. When the high

side MOSFET is turned on, BST1 rises to a peak voltage

equal to VCC + VHS1 where VHS1 is the switch node voltage.

The BST and VCC capacitors should be placed close to the

pins of the LM5045 to minimize voltage transients due to par-

asitic inductances since the peak current sourced to the MOS-

FET gates can exceed 1.5A. The recommended value of the

BST capacitor is 0.1μF or greater. A low ESR / ESL capacitor,

such as a surface mount ceramic, should be used to prevent

voltage droop during the HO transitions.

If the COMP pin is open circuit, the outputs will operate at

maximum duty cycle. The maximum duty cycle for each

phase is limited by the dead-time set by the RD1 resistor. If

the RD1 resistor is set to zero then the maximum duty cycle

is slightly less than 50% due to the internally fixed dead-time.

The internally fixed dead-time is 30ns which does not vary

with the operating frequency. The maximum duty cycle for

each output can be calculated from the following equation:

Where, T1 is the time set by the RD1 resistor and FOSC is the

frequency of the oscillator. For example, if the oscillator fre-

quency is set at 400 kHz and the T1 time set by the RD1

resistor is 60ns, the resulting DMAX will be equal to 0.488.

30145421

FIGURE 4. Timing Diagram Illustrating the Maximum Duty Cycle and Dead-Time Set by RD1

15 www.national.com

LM5045

Synchronous Rectifier Control

Outputs (SR1 & SR2)

Synchronous rectification (SR) of the transformer secondary

provides higher efficiency, especially for low output voltage

converters, compared to the diode rectification. The reduction

of rectifier forward voltage drop (0.5V - 1.5V) to 10mV -

200mV VDS voltage for a MOSFET significantly reduces

rectification losses. In a typical application, the transformer

secondary winding is center tapped, with the output power

inductor in series with the center tap. The SR MOSFETs pro-

vide the ground path for the energized secondary winding and

the inductor current. From Figure 5 it can be seen that when

the HO1/LO2 diagonal is turned ON, power transfer is en-

abled from the primary. During this period, the SR1 MOSFET

is enabled and the SR2 MOSFET is turned-off. The sec-

ondary winding connected to the SR2 MOSFET drain is twice

the voltage of the center tap at this time. At the conclusion of

the HO1/LO2 pulse, the inductor current continues to flow

through the SR2 MOSFET body diode. Since the body diode

causes more loss than the SR MOSFET, efficiency can be

improved by minimizing the T2 period while maintaining suf-

ficient timing margin over all conditions (component toler-

ances, etc.) to prevent the shoot-through current. When HO2/

LO1 enables power transfer from the primary, the SR2 MOS-

FET is enabled and the SR1 MOSFET is off.

During the freewheeling period, the inductor current is almost

equally shared between both the SR1 and SR2 MOSFETs

which effectively shorts the transformer secondary. The SR2

MOSFET is disabled before HO1/LO2 is turned-on. The SR2

MOSFET body diode continues to carry about the half induc-

tor current until the primary power raises the SR2 MOSFET

drain voltage and reverse biases the body diode. Ideally,

dead-time T1 would be set to the minimum time that allows

the SR MOSFET to turn off before the SR MOSFET body

diode starts conducting.

The SR drivers are powered by the REF regulator and each

SR output is capable of sourcing 0.1A and sinking 0.4A peak.

The amplitude of the SR drivers is limited to 5V. The 5V SR

signals enable the LM5045 to transfer SR control across the

isolation barrier either through a solid-state isolator or a pulse

transformer. The actual gate sourcing and sinking currents for

the synchronous MOSFETs are provided by the secondary-

side bias and gate drivers.

T1 and T2 can be programmed by connecting a resistor be-

tween RD1 and RD2 pins and AGND. It should be noted that

while RD1 effects the maximum duty cycle, RD2 does not.

The RD1 and RD2 resistors should be located very close to

the device. The formula for RD1 and RD2 resistors are given

below:

If the desired dead-time for T1 is 60ns, then the RD1 will be

20 kΩ.

30145436

FIGURE 5. Synchronous Rectifier Timing Diagram

www.national.com 16

LM5045

Soft-Start of the Synchronous

Rectifiers

In addition to the basic soft-start already described, the

LM5045 contains a second soft-start function that gradually

turns on the synchronous rectifiers to their steady-state duty

cycle. This function keeps the synchronous rectifiers off dur-

ing the basic soft-start allowing a linear start-up of the output

voltage even into pre-biased loads. Then the SR output duty

cycle is gradually increased to prevent output voltage distur-

bances due to the difference in the voltage drop between the

body diode and the channel resistance of the synchronous

MOSFETs. Initially, when bias is supplied to the LM5045, the

SSSR capacitor is discharged by an internal MOSFET. When

the SS capacitor reaches a 2V threshold and once it is es-

tablished that COMP is in control of the duty cycle i.e. ICOMP

< 800µA, the SSSR discharge is released and SSSR capac-

itor begins charging with a 20µA current source. During the

soft-start of synchronous rectifiers, SR1 and SR2 are turned

on simultaneously in pairs, as shown in Figure 6(a), to avoid

any transformer imbalance. The duty cycle of the SR outputs

gradually increase with increasing SSSR voltage until the du-

ty cycle gets locked into the steady state value as shown in

Figure 6(b). The synchronous rectifier outputs can be dis-

abled by grounding the SSSR pin.

30145432

FIGURE 6. (a) Waveforms during Soft-Start

(b) Waveforms after Soft-Start

Pre-Bias Startup

A common requirement for power converters is to have a

monotonic output voltage start-up into a pre-biased load i.e.

a pre-charged output capacitor. In a pre-biased load condi-

tion, if the synchronous rectifiers are engaged prematurely

they will sink current from the pre-charged output capacitors

resulting in an undesired output voltage dip. This condition is

undesirable and could potentially damage the power convert-

er. The LM5045 utilizes unique control circuitry to ensure

intelligent turn-on of the synchronous rectifiers such that the

output has a monotonic startup. Initially, the SSSR capacitor

is held at ground to disable the synchronous MOSFETs al-

lowing the body diode to conduct. The synchronous rectifier

soft-start is initiated once it is established the duty cycle is

controlled by the COMP instead of the soft-start capacitor i.e.

ICOMP < 800µA and the voltage at the SS pin>2V. The SSSR

capacitor is then released and is charged by a 20µA current

source. Further, as shown in Figure 7, a 1V offset on the

SSSR pin is used to provide additional delay. This delay en-

sures the output voltage is in regulation avoiding any reverse

current when the synchronous MOSFETs are engaged.

Soft-Stop

As shown in Figure 8, if the UVLO pin voltage falls below the

1.25V standby threshold, but above the 0.4V shutdown

threshold, the SSSR capacitor is soft-stopped with a 60µA

current source (3 times the charging current). Once the SSSR

pin reaches the 1.0V threshold, both the SS and SSSR pins

are immediately discharged to GND. Soft-stopping the power

converter gradually winds down the energy in the output ca-

pacitors and results in a monotonic decay of the output volt-

age. During the hiccup mode, the same sequence is executed

except that the SSSR is discharged with a 120µA current

source (6 times the charging current). In case of an OVP, VCC

UV, thermal limit or a VREF UV condition, the power converter

hard-stops, whereby all of the control outputs are driven to a

low state immediately.

17 www.national.com

LM5045

30145433

FIGURE 7. Pre-Bias Voltage Startup Waveforms

Soft-Stop Off

The Soft-Start Off (SSOFF) pin gives additional flexibility by

allowing the power converter to be configured for hard-stop

during line UVLO and hiccup mode condition. If the SS OFF

pin is pulled up to the 5V REF pin, the power converter hard-

stops in any fault condition. Hard-stop drives each control

output to a low state immediately. Refer to Table 1 for more

details.

30145434

FIGURE 8. Stop-Stop Waveforms during a UVLO Event

www.national.com 18

LM5045

Table 1: Soft-Stop in Fault

Conditions

Fault Condition SSSR

UVLO

(UVLO<1.25V)

Soft-Stop

3x the charging rate

OVP

(OVP>1.25V)

Hard-Stop

Hiccup

(CS>0.75 and RES>1V)

Soft-Stop

6x the charging rate

VCC/VREF UV Hard-Stop

Internal Thermal Limit Hard-Stop

Note: All the above conditions are valid with SSOFF pin tied

to GND. If SSOFF=5V, the LM5045 hard-stops in all the con-

ditions. The SS pin remains high in all the conditions until the

SSSR pin reaches 1V.

Thermal Protection

Internal thermal shutdown circuitry is provided to protect the

integrated circuit in the event the maximum rated junction

temperature is exceeded. When activated, typically at 160°C,

the controller is forced into a shutdown state with the output

drivers, the bias regulators (VCC and REF) disabled. This

helps to prevent catastrophic failures from accidental device

overheating. During thermal shutdown, the SS and SSSR ca-

pacitors are fully discharged and the controller follows a nor-

mal start-up sequence after the junction temperature falls to

the operating level (140 °C).

Applications Information

CONTROL METHOD SELECTION

The LM5045 is a versatile PWM control IC that can be con-

figured for either current mode control or voltage mode con-

trol. The choice of the control method usually depends upon

the designer preference. The following must be taken into

consideration while selecting the control method. Current

mode control can inherently balance flux in both phases of the

full-bridge topology. The full-bridge topology, like other dou-

ble ended topologies, is susceptible to the transformer core

saturation. Any asymmetry in the volt-second product applied

between the two alternating phases results in flux imbalance

that causes a dc buildup in the transformer. This continual dc

buildup may eventually push the transformer into saturation.

The volt-second asymmetry can be corrected by employing

current mode control. In current mode control, a signal rep-

resentative of the primary current is compared against an

error signal to control the duty cycle. In steady-state, this re-

sults in each phase being terminated at the same peak current

by adjusting the pulse-width and thus applying equal volt-

seconds to both the phases.

Current mode control can be susceptible to noise and sub-

harmonic oscillation, while voltage mode control employs a

larger ramp for PWM and is usually less susceptible. Voltage-

mode control with input line feed-forward also has excellent

line transient response. When configuring for voltage mode

control, a dc blocking capacitor can be placed in series with

the primary winding of the power transformer to avoid any flux

imbalance that may cause transformer core saturation.

VOLTAGE MODE CONTROL USING THE LM5045

To configure the LM5045 for voltage mode control, an exter-

nal resistor (RFF) and capacitor (CFF) connected to VIN, AG-

ND, and the RAMP pins is required to create a saw-tooth

modulation ramp signal shown in Figure 9. The slope of the

signal at RAMP will vary in proportion to the input line voltage.

The varying slope provides line feed-forward information nec-

essary to improve line transient response with voltage mode

control. With a constant error signal, the on-time (TON) varies

inversely with the input voltage (VIN) to stabilize the Volt-

Second product of the transformer primary. Using a line feed-

forward ramp for PWM control requires very little change in

the voltage regulation loop to compensate for changes in in-

put voltage, as compared to a fixed slope oscillator ramp.

Furthermore, voltage mode control is less susceptible to

noise and does not require leading edge filtering. Therefore,

it is a good choice for wide input range power converters.

Voltage mode control requires a Type-III compensation net-

work, due to the complex-conjugate poles of the L-C output

filter.

30145424

FIGURE 9. Feed-Forward Voltage Mode Configuration

19 www.national.com

LM5045

The recommended capacitor value range for CFF is from

100pF to 1800pF. Referring to Figure 9, it can be seen that

CFF value must be small enough to be discharged with in the

clock pulse-width which is typically within 50ns. The RDS(ON)

of the internal discharge FET is 5.5Ω.

The value of RFF required can be calculated from

For example, assuming a VRAMP of 1.5V (a good compromise

of signal range and noise immunity), at VINMIN of 36V (oscil-

lator frequency of 400 kHz and CFF = 470pF results in a value

for RFF of 125 kΩ.

CURRENT MODE CONTROL USING THE LM5045

The LM5045 can be configured for current mode control by

applying a signal proportional to the primary current to the

RAMP pin. One way to achieve this is shown in Figure 10.

The primary current can be sensed using a current trans-

former or sense resistor, the resulting signal is filtered and

applied to the RAMP pin through a resistor used for slope

compensation. It can be seen that the signal applied to the

RAMP pin consists of the primary current information from the

CS pin plus an additional ramp for slope compensation,

added by the resistor RSLOPE.

The current sense resistor is selected such that during over

current condition, the voltage across the current sense resis-

tor is above the minimum CS threshold of 728mV.

In general, the amount of slope compensation required to

avoid sub-harmonic oscillation is equal to at least one-half the

down-slope of the output inductor current, transformed to the

primary. To mitigate sub-harmonic oscillation after one

switching period, the slope compensation has to be equal to

one times the down slope of the filter inductor current trans-

posed to primary. This is known as deadbeat control. The

slope compensation resistor required to implement dead-beat

control can be calculated as follows:

Where NTR is the turns-ratio with respect to the secondary.

For example, for a 3.3V output converter with a turns-ratio

between primary and secondary of 9:1, an output filter induc-

tance (LFILTER) of 800nH and a current sense resistor

(RSENSE) of 150mΩ, RSLOPE of 1.67kΩ will suffice.

VIN and VCC

The voltage applied to the VIN pin, which may be the same

as the system voltage applied to the power transformer’s pri-

mary (VPWR), can vary in the range of the 14 to 100V. It is

recommended that the filter shown in Figure 11 be used to

suppress the transients that may occur at the input supply.

This is particularly important when VIN is operated close to

the maximum operating rating of the LM5045. The current into

VIN depends primarily on the LM5045’s operating current, the

switching frequency, and any external loads on the VCC pin,

that typically include the gate capacitances of the power

MOSFETs. In typical applications, an auxiliary transformer

winding is connected through a diode to the VCC pin. This pin

must raise VCC voltage above 8V to shut off the internal start-

up regulator.

After the outputs are enabled and the external VCC supply

voltage has begun supplying power to the IC, the current into

the VIN pin drops below 1mA. VIN should remain at a voltage

equal to or above the VCC voltage to avoid reverse current

through the internal body diode of the internal VCC regulator.

FOR APPLICATIONS WITH > 100V INPUT

For applications where the system input voltage exceeds

100V, VIN can be powered from an external start-up regulator

as shown in Figure 12. In this configuration, the VIN and VCC

pins should be connected together. The voltage at the VCC

and VIN pins must be greater than 10V (>Max VCC reference

voltage) yet not exceed 16V. To enable operation the VCC

voltage must be raised above 10V. The voltage at the VCC

pin must not exceed 16V. The voltage source at the right side

of Figure 12 is typically derived from the power stage, and

becomes active once the LM5045’s outputs are active.

30145425

FIGURE 10. Current Mode Configuration

www.national.com 20

LM5045

30145430

FIGURE 11. Input Transient Protection

30145437

FIGURE 12. Start-up Regulator for VPWR>100V

UVLO AND OVP VOLTAGE DIVIDER SELECTION

Two dedicated comparators connected to the UVLO and OVP

pins are used to detect under voltage and over voltage con-

ditions. The threshold values of both these comparators are

set at 1.25V. The two functions can be programmed inde-

pendently with two separate voltage dividers from VIN to

AGND as shown in Figure 13 and Figure 14, or with a three-

resistor divider as shown in Figure 15. Independent UVLO

and OVP pins provide greater flexibility for the user to select

the operational voltage range of the system. When the UVLO

pin voltage is below 0.4V, the controller is in a low current

shutdown mode. For a UVLO pin voltage greater than 0.4V

but less than 1.25V the controller is in standby mode. Once

the UVLO pin voltage is greater than 1.25V, the controller is

fully enabled. Two external resistors can be used to program

the minimum operational voltage for the power converter as

shown in Figure 13. When the UVLO pin voltage falls below

the 1.25V threshold, an internal 20µA current sink is enabled

to lower the voltage at the UVLO pin, thus providing threshold

hysteresis. Resistance values for R1 and R2 can be deter-

mined from the following equations:

Where VPWR is the desired turn-on voltage and VHYS is the

desired UVLO hysteresis at VPWR.

For example, if the LM5045 is to be enabled when VPWR

reaches 33V, and disabled when VPWR is decreased to 31V,

R1 should be 100kΩ, and R2 should be 4.2kΩ. The voltage at

the UVLO pin should not exceed 7V at any time.

Two external resistors can be used to program the maximum

operational voltage for the power converter as shown in Fig-

ure 14. When the OVP pin voltage rises above the 1.25V

threshold, an internal 20µA current source is enabled to raise

the voltage at the OVP pin, thus providing threshold hystere-

sis. Resistance values for R1 and R2 can be determined from

the following equations:

If the LM5045 is to be disabled when VPWR-OFF reaches 80V

and enabled when it is decreased to 78V. R1 should be

100kΩ, and R2 should be 1.5 kΩ. The voltage at the OVP pin

should not exceed 7V at any time.

21 www.national.com

LM5045

30145438

FIGURE 13. Basic UVLO Configuration

30145439

FIGURE 14. Basic OVP Configuration

30145443

FIGURE 15. UVLO/OVP Divider

www.national.com 22

LM5045

The UVLO and OVP can also be set together using a 3 re-

sistor divider ladder as shown in Figure 15. R1 is calculated

as explained in the basic UVLO divider selection. Using the

same values, as in the above two examples, for the UVLO

and OVP set points, R1 and R3 remain the same at 100kΩ

and 1.5kΩ. The R2 is 2.7kΩ obtained by subtracting R3 from

4.2kΩ.

Remote configuration of the controller’s operational modes

can be accomplished with open drain device(s) connected to

the UVLO pin as shown in Figure 16.

Figure 17 shows an application of the OVP comparator for

Remote Thermal Protection using a thermistor (or multiple

thermistors) which may be located near the main heat

sources of the power converter. The negative temperature

coefficient (NTC) thermistor is nearly logarithmic, and in this

example a 100kΩ thermistor with the β material constant of

4500 Kelvin changes to approximately 2kΩ at 130ºC. Setting

R1 to one-third of this resistance (665Ω) establishes 130ºC as

the desired trip point (for VREF = 5V). In a temperature band

from 20ºC below to 20ºC above the OVP threshold, the volt-

age divider is nearly linear with 25mV per ºC sensitivity.

R2 provides temperature hysteresis by raising the OVP com-

parator input by R2 x 20µA. For example, if a 22kΩ resistor is

selected for R2, then the OVP pin voltage will increase by 22k

x 20µA = 506mV. The NTC temperature must therefore fall

by 506mV / 25mV per ºC = 20ºC before the LM5045 switches

from standby mode to the normal mode.

30145444

FIGURE 16. Remote Standby and Disable Control

30145414

FIGURE 17. Remote Thermal Protection

23 www.national.com

LM5045

CURRENT SENSE

The CS pin receives an input signal representative of its

transformer’s primary current, either from a current sense

transformer or from a resistor located at the junction of source

pin of the primary switches, as shown in Figure 18 and Figure

19 respectively. In both the cases, the filter components RF

and CF should be located as close to the IC as possible, and

the ground connection from the current sense transformer, or

RSENSE should be a dedicated trace to the appropriate GND

pin. Please refer to the layout section for more layout tips.

The current sense components must provide a signal >

710mV at the CS pin during an over-load event. Once the

voltage on the CS pin crosses the current limit threshold, the

current sense comparator terminates the PWM pulse and

starts to charge the RES pin. Depending on the configuration

of the RES pin, the LM5045 will eventually initiate a hiccup

mode restart or be in continuous current limit.

30145415

FIGURE 18. Transformer Current Sense

30145422

FIGURE 19. Resistor Current Sense

www.national.com 24

LM5045

HICCUP MODE CURRENT LIMIT RESTART

The operation of the hiccup mode restart circuit is explained

in the Functional Description section. During a continuous

current limit condition, the RES pin is charged with 30µA cur-

rent source. The restart delay time required to reach the 1.0V

threshold is given by:

This establishes the time allowed before the IC initiates a hic-

cup restart sequence. For example, if the CRES=0.01µF, the

time TCS as noted in Figure 20 below is 334µs. Once the RES

pin reaches 1.0V, the 30µA current source is turned-off and

a 10µA current source is turned-on during the ramp up to 4V

and a 5µA is turned on during the ramp down to 2V. The hic-

cup mode off-time is given by:

With a CRES=0.01µF, the hiccup time is 49ms. Once the hic-

cup time is finished, the RES pin is pulled-low and the SS pin

is released allowing a soft-start sequence to commence.

Once the SS pin reaches 1V, the PWM pulses will commence.

The hiccup mode provides a cool-down period for the power

converter in the event of a sustained overload condition there-

by lowering the average input current and temperature of the

power components during such an event.

30145416

FIGURE 20. Hiccup Mode Delay and Soft-Start Timing Diagram

25 www.national.com

LM5045

AUGMENTING THE GATE DRIVE STRENGTH

The LM5045 includes powerful 2A integrated gate drivers.

However, in certain high power applications (>500W), it might

be necessary to augment the strength of the internal gate

driver to achieve higher efficiency and better thermal perfor-

mance. In high power applications, typically, the I2xR loss in

the primary MOSFETs is significantly higher than the switch-

ing loss. In order to minimize the I2xR loss, either the primary

MOSFETs are paralleled or MOSFETs with low RDS (on) are

employed. Both these scenarios increase the total gate

charge to be driven by the controller IC. An increase in the

gate charge increases the FET transition time and hence in-

creases the switching losses. Therefore, to keep the total

losses within a manageable limit the transition time needs to

be reduced.

Generally, during the miller capacitance charge/discharge the

total available driver current is lower during the turn-off pro-

cess than during the turn-on process and often it is enough to

speed-up the turn-off time to achieve the efficiency and ther-

mal goals. This can be achieved simply by employing a PNP

device, as shown in Figure 21, from gate to source of the

power FET. During the turn-on process, when the LO1 goes

high, the current is sourced through the diode D1 and the BJT

Q1 provides the path for the turn-off current. Q1 should be

located as close to the power FET as possible so that the turn-

off current has the shortest possible path to the ground and

does not have to pass through the controller.

30145462

FIGURE 21. Circuit to Speed-up the Turn-off Process

Depending on the gate charge characteristics of the primary

FET, if it is required to speed up both the turn-on and the turn-

off time, a bipolar totem pole structure as shown in Figure

22 can be used. When LO1 goes high, the gate to source

current is sourced through the NPN transistor Q1 and similar

to the circuit shown in Figure 21 when LO1 goes low, the PNP

transistor Q2 expedites the turn-off process.

www.national.com 26

LM5045

30145463

FIGURE 22. Bipolar Totem Pole Arrangement

Alternatively, a low side gate driver such as LM5112 can be

utilized instead of the discrete totem pole. The LM5112 comes

in a small package with a 3A source and a 7A sink capability.

While driving the high-side FET, the HS1 acts as a local

ground and the boot capacitor between the BST and HS pins

acts as VCC.

30145464

FIGURE 23. Using a Low Side Gate Driver to Augment Gate Drive Strength

27 www.national.com

LM5045

PRINTED CIRCUIT BOARD LAYOUT

The LM5045 current sense and PWM comparators are very

fast and respond to short duration noise pulses. The compo-

nents at the CS, COMP, SLOPE, RAMP, SS, SSSR, RES,

UVLO, OVP, RD1, RD2, and RT pins should be physically

close as possible to the IC, thereby minimizing noise pickup

on the PC board trace inductance. Eliminating or minimizing

via’s in these critical connections are essential. Layout con-

sideration is critical for the current sense filter. If a current

sense transformer is used, both leads of the transformer sec-

ondary should be routed to the sense filter components and

to the IC pins. The ground side of the transformer should be

connected via a dedicated PC board trace to the AGND pin,

rather than through the ground plane. If the current sense cir-

cuit employs a sense resistor in the drive transistor source,

low inductance resistors should be used. In this case, all the

noise sensitive, low-current ground trace should be connect-

ed in common near the IC, and then a single connection made

to the power ground (sense resistor ground point).

The gate drive outputs of the LM5045 should have short, di-

rect paths to the power MOSFETs in order to minimize in-

ductance in the PC board. The boot-strap capacitors required

for the high side gate drivers should be located very close to

the IC and connected directly to the BST and HS pins. The

VCC and REF capacitors should also be placed close to their

respective pins with short trace inductance. Low ESR and

ESL ceramic capacitors are recommended for the boot-strap,

VCC and the REF capacitors. The two ground pins (AGND,

PGND) must be connected together directly underneath the

IC with a short, direct connection, to avoid jitter due to relative

ground bounce.

Application Circuit Example

The following schematic shows an example of a 100W full-

bridge converter controlled by LM5045. The operating input

voltage range is 36V to 75V, and the output voltage is 3.3V.

The output current capability is 30 Amps. The converter is

configured for current mode control with external slope com-

pensation. An auxiliary winding is used to raise the VCC

voltage to reduce the controller power dissipation.

www.national.com 28

LM5045

Evaluation Board Schematic

30145458

29 www.national.com

LM5045

Physical Dimensions inches (millimeters) unless otherwise noted

Molded TSSOP-28

NS Package Number MXA28A

28-Lead LLP Package

NS Package Number SQA28A

www.national.com 30

LM5045

Notes

31 www.national.com

LM5045

Notes

LM5045 Full-Bridge PWM Controller with Integrated MOSFET Drivers

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

www.national.com

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench

Audio www.national.com/audio App Notes www.national.com/appnotes

Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns

Data Converters www.national.com/adc Samples www.national.com/samples

Interface www.national.com/interface Eval Boards www.national.com/evalboards

LVDS www.national.com/lvds Packaging www.national.com/packaging

Power Management www.national.com/power Green Compliance www.national.com/quality/green

Switching Regulators www.national.com/switchers Distributors www.national.com/contacts

LDOs www.national.com/ldo Quality and Reliability www.national.com/quality

LED Lighting www.national.com/led Feedback/Support www.national.com/feedback

Voltage References www.national.com/vref Design Made Easy www.national.com/easy

PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions

Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero

Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic

PLL/VCO www.national.com/wireless PowerWise® Design

University

www.national.com/training

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email: support@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265