NC7S14P5X - ON SEMICONDUCTOR

July, 2019 − Rev. 3

1Publication Order Number:

NC7S14/D

NC7S14

TinyLogic HS Inverter with

Schmitt Trigger Input

Description

The NC7S14 is a single high performance CMOS Inverter with

Schmitt Trigger input. The circuit design provides hysteresis between

the positive−going and negative going input thresholds thereby

improving noise margins.

Advanced Silicon Gate CMOS fabrication assures high speed and

low power circuit operation over a broad VCC range. ESD protection

diodes inherently guard both input and output with respect to the VCC

and GND rails.

Features

•Space Saving SC−74A and SC−88A 5−Lead Package

•Ultra Small MicroPak™ Leadless Package

•Schmitt Input Hysteresis: >1 V Typ

•High Speed: tPD = 4.5 ns Typ

•Low Quiescent Power: ICC < 1 mA

•Balanced Output Drive: 2 mA IOL, −2 mA IOH

•Broad VCC Operating Range: 2 V – 6 V

•Balanced Propagation Delays

•Specified for 3 V Operation

•These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS

Compliant

Figure 1. Logic Symbol

YA 1

IEEE / IEC

UU, 7S14, S14 = Specific Device Code

KK = 2−Digit Lot Run Traceability Code

XY = 2−Digit Date Code Format

Z = Assembly Plant Code

T = Die Run Code

= Year Coding Scheme

= Plant Code Identifier

= Eight−Week Datacoding Scheme

See detailed ordering, marking and shipping information in the

package dimensions section on page 5 of this data sheet.

ORDERING INFORMATION

MARKING

DIAGRAMS

www.onsemi.com

SC−88A

CASE 419AC−01

SIP6

CASE 127EB

UUKK

XYZ

S14T

Pin 1

SC−74A

CASE 318BQ 7S14T

NC7S14

www.onsemi.com

Pin Configurations

VCC

GND Y

Figure 2. SC−88A and SC−74A (Top View)

NC 1 6 VCC

A 2 5 NC

GND 3 4 Y

Figure 3. MicroPak (Top Through View)

PIN DESCRIPTIONS

Pin Name Description

A Input

Y Output

NC No Connect

FUNCTION TABLE (Y = A)

Inputs Output

A Y

L H

H L

H = HIGH Logic Level

L = LOW Logic Level

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Min Max Unit

VCC Supply Voltage −0.5 6.5 V

IIK DC Input Diode Current VIN ≤ −0.5 V − −20 mA

VIN ≥ VCC + 0.5 V −+20

VIN DC Input Voltage −0.5 VCC + 0.5 V

IOK DC Output Diode Current VOUT < −0.5 V − −20 mA

VOUT > VCC + 0.5 V −+20

VOUT DC Output Voltage −0.5 VCC + 0.5 V

IOUT DC Output Source or Sink Current −±12.5 mA

ICC or IGND DC VCC or Ground Current per Output Pin −±25 mA

TSTG Storage Temperature −65 +150 °C

TJJunction Temperature −+150 °C

TLLead Temperature (Soldering, 10 Seconds) −+260 °C

PDPower Dissipation in Still Air SC−74A −225 mW

SC−88A−5−190

MicroPak −327

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

NC7S14

www.onsemi.com

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Conditions Min Max Unit

VCC Supply Voltage 2.0 6.0 V

VIN Input Voltage 0 VCC V

VOUT Output Voltage 0 VCC V

TAOperating Temperature −40 +85 °C

qJA Thermal Resistance SC−74A −555 °C/W

SC−88A−5−659

MicroPak −382

Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond

the Recommended Operating Ranges limits may affect device reliability.

1. Unused inputs must be held HIGH or LOW. They may not float.

DC ELECTICAL CHARACTERISTICS

Symbol Parameter VCC (V) Conditions

TA = +25°C TA = −40 to +85°C

Unit

Min Typ Max Min Max

VP Positive Threshold Voltage 2.0

3.0

4.5

6.0

−

1.29

1.90

2.73

3.56

1.5

2.2

3.15

4.2

−

1.6

2.2

3.15

4.2

VN Negative Threshold Voltage 2.0

3.0

4.5

6.0

0.3

0.6

1.13

1.5

0.70

1.05

1.66

2.24

−

0.3

0.6

1.13

1.5

VH Hysteresis Voltage 2.0

3.0

4.5

6.0

0.3

0.4

0.6

0.8

0.59

0.85

1.08

1.31

1.0

1.3

1.4

1.7

0.3

0.4

0.6

0.8

1.0

1.3

1.4

1.7

VOH HIGH Level Output Voltage 2.0

3.0

4.5

6.0

IOH = −20 mA

VIN = VIL

1.90

2.90

4.40

5.90

2.0

3.0

4.5

6.0

−

1.90

2.90

4.40

5.90

−

3.0

4.5

6.0

VIN = VIL

IOH = −1.3 mA

IOH = −2.0 mA

IOH = −2.6 mA

2.68

4.18

5.68

2.87

4.37

5.86

−

2.63

4.13

5.63

−

VOL LOW Level Output Voltage 2.0

3.0

4.5

6.0

IOL = 20 mA

VIN = VIH

−

0.0

0.10

−

0.10

3.0

4.5

6.0

VIN = VIH

IOL = 1.3 mA

IOL = 2.0 mA

IOL = 2.6 mA

−

0.1

0.26

−

0.33

IIN Input Leakage Current 6.0 VIN = VCC, GND − − ±0.1 −±1.0 mA

ICC Quiescent Supply Current 6.0 VIN = VCC, GND − − 1.0 −10.0 mA

NC7S14

www.onsemi.com

AC ELECTRICAL CHARACTERISTICS

Symbol Parameter VCC (V) Conditions

TA = +25°C TA = −40 to +85°C

Unit

Min Typ Max Min Max

tPLH

tPHL

Propagation Delay (Figure 4, 6) 5.0 CL = 15 pF −4.5 21 − − ns

2.0

3.0

4.5

6.0

CL = 50 pF −

−

8.5

7.5

100

−

125

tTLH

tTHL

Output Transition Time

(Figure 4, 6)

5.0 CL = 15 pF −3 8 − − ns

2.0

3.0

4.5

6.0

CL = 50 pF −

−

125

−

145

CIN Input Capacitance Open −2 10 −10 pF

CPD Power Dissipation Capacitance

(Figure 5)

5.0 (Note 2) −7− − − pF

2. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at

no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression:

ICCD = (CPD) (VCC) (fIN) + (ICCstatic).

AC Loading and Waveforms

Figure 4. AC Test Circuit

Figure 5. ICCD Test Circuit

Figure 6. AC Waveforms

Input = AC Waveforms;

PRR = Variable; Duty Cycle = 50%.

INPUT

VCC

INPUT OUTPUT

CL includes load and stray capacitance

Input PRR = 1.0 MHz; tW = 500 ns

NC7S14

www.onsemi.com

ORDERING INFORMATION

Part Number Top Mark Package Description Shipping†

NC7S14M5X 7S14 SC−74A 3000 / Tape & Reel

NC7S14P5X S14 SC−88A 3000 / Tape & Reel

NC7S14L6X UU SIP6, MicroPak 5000 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

MicroPak is trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.

SIP6 1.45X1.0

CASE 127EB

ISSUE O

DATE 31 AUG 2016

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically

disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the

rights of others.

98AON13590G

DOCUMENT NUMBER:

DESCRIPTION:

Electronic versions are uncontrolled except when accessed directly from the Document Repository.

Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.

PAGE 1 OF 1

SIP6 1.45X1.0

SC−74A

CASE 318BQ

ISSUE B DATE 18 JAN 2018

SCALE 2:1

GENERIC

MARKING DIAGRAM*

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

*This information is generic. Please refer to

device data sheet for actual part marking.

Pb−Free indicator, “G” or microdot “ G”,

may or may not be present. Some products

may not follow the Generic Marking.

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH

THICKNESS. MINIMUM LEAD THICKNESS IS THE

MINIMUM THICKNESS OF BASE MATERIAL.

4. DIMENSIONS A AND B DO NOT INCLUDE MOLD

FLASH, PROTRUSIONS, OR GATE BURRS. MOLD

FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT

EXCEED 0.15 PER SIDE.

DIM MIN MAX

MILLIMETERS

A0.90 1.10

b0.25 0.50

e0.95 BSC

A1 0.01 0.10

c0.10 0.26

L0.20 0.60

M0 10

E2.50 3.00

123

54 E

0.20

CAB

CSEATING

PLANE

DET AIL A

TOP VIEW

SIDE VIEW

END VIEW 1.35 1.65

2.85 3.15

2.40

0.70

DIMENSIONS: MILLIMETERS

RECOMMENDED

0.95

PITCH

1.00

eA1

0.05

DETAIL A

XXX MG

XXX = Specific Device Code

M = Date Code

G= Pb−Free Package

(Note: Microdot may be in either location)

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

http://onsemi.com

October, 2002 − Rev. 0 Case Outline Number:

XXX

DOCUMENT NUMBER:

STATUS:

NEW STANDARD:

DESCRIPTION:

98AON66279G

ON SEMICONDUCTOR STANDARD

SC−74A

Electronic versions are uncontrolled except when

accessed directly from the Document Repository. Printed

versions are uncontrolled except when stamped

“CONTROLLED COPY” in red.

PAGE 1 OF 2

DOCUMENT NUMBER:

98AON66279G

PAGE 2 OF 2

ISSUE REVISION DATE

ORELEASED FOR PRODUCTION. REQ BY I. HYLAND. 27 JUN 2017

ACORRECTED MARKING DIAGRAM FROM 6 TO 5−LEAD. REQ BY I. HYLAND. 20 SEP 2017

BCORRECTED SOLDERING FOOTPRINT PITCH FROM 3.40MM TO 2.40MM. REQ.

BY I. HYLAND. 18 JAN 2018

January, 2018 − Rev. B Case Outline Number

318BQ

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, af filiates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

SC−88A (SC−70 5 Lead), 1.25x2

CASE 419AC−01

ISSUE A

DATE 29 JUN 2010

L1 L2

bA1

TOP VIEW

SIDE VIEW END VIEW

Notes:

(1) All dimensions are in millimeters. Angles in degrees.

(2) Complies with JEDEC MO-203.

SYMBOL MIN NOM MAX

0º 8º

0.00

0.15

0.10

0.26

1.80

1.15

0.65 BSC

0.15 BSC

1.10

0.10

0.30

0.18

0.46

2.20

2.40

1.35

0.80

θ1 4º 10º

A2 0.80 1.00

0.42 REF

0.36

2.00

2.10

1.25

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically

disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the

rights of others.

98AON34260E

DOCUMENT NUMBER:

DESCRIPTION:

Electronic versions are uncontrolled except when accessed directly from the Document Repository.

Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.

PAGE 1 OF 1

SC−88A (SC−70 5 LEAD), 1.25X2

www.onsemi.com

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent

coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.

ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,

regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer

application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not

designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification

in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized

application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and

expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such

claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

TECHNICAL SUPPORT

North American Technical Support:

Voice Mail: 1 800−282−9855 Toll Free USA/Canada

Phone: 011 421 33 790 2910

LITERATURE FULFILLMENT:

Email Requests to: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Europe, Middle East and Africa Technical Support:

Phone: 00421 33 790 2910

For additional information, please contact your local Sales Representative

◊