Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height W.FL2 Series Occupied Mounting Area 2.0mm 2.0mm W. FL2 Series Note: The W. FL2 Series is not compatible with X.FL, W.FL Series. 3. Extremely light weight The world's smallest and lightest class of coaxial connectors. Receptacle: 5.0mg Right angle plug:16.7mg(062), 17.4mg(040), 15.3mg(032) W. FL2 Series W. FL Series W.FL2-LP-032HF(06) W.FL2-LP-040(06) W.FL2-LP-040HF(06) W.FL2-LP-062HF W.FL-LP-040(06) W.FL-LP-040HF(06) W.FL-R-SMT-1 W.FL2-R-SMT-1 4. Frequency range up to 6 GHz Fig.1 DC to 3 GHz: V.S.W.R. of 1.3 max. 3 GHz to 6 GHz: V.S.W.R. of 1.4 max. 5. Automatic board placement W. FL2 Plug and Receptacle Packaged on tape-and-reel the receptacles can be placed with vacuum nozzles of the automatic placement equipment. L#;A'Eaj\ 6. Plugs are terminated with ultra-fine coaxial (fluorinated resin insulated) cable 8VWaZ &#&PB6M&#(R The use of ultra-fine coaxial(fluorinated resin insulated)cables on these connectors offer the ability to complete connections in small, confined spaces with a smooth, easy operation. (#( 9^V#&#%!%#-&!%#* As with X.FL, W.FL Series, the receptacles occupies an area of 3.4 mm2 and share the same land pattern. Mated height comparison (with W.FL Series) 1.4 [MAX1.55] 1. Nominal mated height of 1.18 mm (Max. 1.3 mm) 2. Small board footprint 1.18 [MAX1.3] Features W. FL Series 7. Simple connector mating / un-mating Use of the available mating / un-mating tools assures correct connection / disconnection of the plug and receptacle. L#;A'"G"HBI"& GZXZeiVXaZ 8. Halogen-free*(Receptacle, Plug(HF type)) *As defined by IEC61249-2-21 Fig.2 Br-900 ppm maximum, Cl-900 ppm maximum, Cl+Br combined-1,500 ppm maximum. 2014.11w 1 W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height Specifications Nominal characteristic impedance 50o Operating temperature range Rating Frequency range Item DC to 6 GHz Storage temperature range -40C to +90C (90%RH max.) -30C to +70C (90%RH max.)Note 1 Specification 1. Contact resistance 20 mo max. (center contact), l0 mo max. (outer contact) 2. Insulation resistance 500 Mo min., 100 V DC 3. Withstanding voltage 200 V AC / 1 minute 1.3 max. (DC to 3 GHz) 4. V.S.W.R. 1.4 max. (3 GHz to 6 GHz) * V.S.W.R. Measurement as shown on the block diagram below. Note: Verify connection and measurement setup. Network Analyzer Test Set Test Port Test Post Cable D.U.T Termination Note1: Cable assembly measurements with SMA conversion adapters mated with W.FL2 plug at each end of the 100cm long ultra-fine coaxial cable. Note2: Receptacles mounted on a 50 ohms glass epoxy board. Measurements were conducted with SMA conversion adapters attached. Note1. The term "storage" refers to products stored for long period of time prior to mounting and use. Materials Plugs - Right Angle Part Shell Material Finish Phosphor bronze Silver plated/Gold plated(062) Insulator PBT Color: Black, UL94V-0 Insulator (HF type) LCP Color: Milky white, UL94V-0 Phosphor bronze Gold plated Female center contact Receptacle Part Shell Insulator Male center contact 2 Material Finish Phosphor bronze Silver plated LCP Color: Black, UL94V-0 Brass Gold plated W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height Cable Assembly(Plug) 2 W.FL2-LP-040(06), W.FL2-LP-040HF(06) (Applicable cable : outer diameter 0.81) 0.91 3.3 2 W.FL2-LP-032HF(06) (Applicable cable : outer diameter 0.5) 0.91 3.35 2 W.FL2-LP-062HF (Applicable cable : outer diameter 1.0) 0.89 3.3 [Plugs can be ordered only as terminated cable assemblies.] 3 W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height BHow to specify Cable Assembly [Double-ended cable assembly] [Single-ended cable assembly] L (mm) L (mm) Ordering infometioan Ordering information Standard Tolerances for (L) Used plug: W.FL2-LP-040(06), W.FL2-LP-040HF(06) DoubleEnded SingleEnded W.FL2 - 2LP - HF6 - 04NTV - A - (L) Series name : WFL2, W.FL2 Environmental compliant 4 1L=200 to 500 8 1L=500 to 1000 12 Note: Minimum available length(L) is 35mm. 04N: 0.81mm dia. ultra-fine Cable type LP: Single ended Assembly type Standard tolerance(mm) L=Longer than 1000mm1000 1.5% of (L) W.FL2 - LP - HF6 - 04NTV - A - (L) (L)mm *L=35 to 200 coaxial cable 2LP: Double ended Cable color HF6: Halogen-free Cable outer conductor TV: Tin Plated braided wire 6: RoHS compliant Total length (mm) 1: White, 2: Black Length(L) Used plug: W.FL2-LP-032HF(06) DoubleEnded SingleEnded W.FL2 - 2LP - HF6 - 032NTS - A - (L) W.FL2 - LP - HF6 - 032NTS - A - (L) Series name Assembly type : WFL2, W.FL2 Cable type 032N: 0.5mm dia. ultra-fine coaxial cable LP: Single ended Cable color 1: White, 2: Black 2LP: Double ended Cable outer conductor HF6: Halogen-free Environmental compliant Total length (mm) TS: Tin Plated fiber or paper covered copper winding wire Length(L) Used plug: W.FL2-LP-062HF DoubleEnded SingleEnded W.FL2 - 2LP - HF - 062NSC - A - (L) W.FL2 - LP - HF - 062NSC - A - (L) Series name Assembly type 4 Environmental compliant : WFL2, W.FL2 Cable type 062N: 1.0mm dia. ultra-fine coaxial cable LP: Single ended Cable color 1: Gray, 2: Black, 3: White 2LP: Double ended HF: Halogen-free Cable outer conductor Total length (mm) SC: Outer tin plated braided wire Inner conductor silver plated Length(L) W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height Receptacles BRecommended PCB mounting pattern (Note 1) 2.6 1.4 0.5 1.3 SIG 1.7 2 SIG 0.65 1.3 1.7 2 0.3 1.5 1.3 0.7 0.25 0.3 GND Part No. HRS No. Packaging W.FL2-R-SMT-1(60) 331-0315-4 60 Reel (5,000 pcs/reel) W.FL2-R-SMT-1(80) 331-0315-4 80 Reel (10,000 pcs/reel) GND No conductive traces in this area Note 1: The land pattern is the same as that of the X.FL, W.FL series connectors. RoHS Yes BEmbossed Carrier Tape Dimensions (IEC 60286-3 compliant) Embossed Carrier Tape Dimensions Embossed Carrier Tape Dimensions &#* ) ' &(#* BViZg^VaEHL]^iZ &' ((% *#* &#,* (W.FL2-R-SMT-1(60) 8mm pitch) Reel Dimensions 6 - 6H86A:;G:: ' &( ) & ' ' & &' *#* &#,* #* (W.FL2-R-SMT-1(80) 4mm pitch) ) 5 W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height Conversion Adapters SMA Conversion Adapter (W.FL2 side jack - SMA side plug) (10.15) 8HEX All dimensions: mm Note: Used for performance measurements only. The W.FL2 mating side has lower retention force when mated with the corresponding part. Part No. HRS No. Packaging RoHS HRMP-W.FL2J 311-0394-6 1 Yes SMA Conversion Adapter (W.FL2/W.FL side plug - SMA side jack) 13.8 (4.05) 5.6 O6.35 6 1/4-36UNS-2A All dimensions: mm Note: Used for performance measurements only. The W.FL/W.FL2 mating side has lower retention force when mated with the corresponding part. Part No. HRS No. Packaging RoHS HRMJ-W.FLP(40) 311-0368-6 40 1 Yes SMA Conversion Adapter (18.14) 5.5 (4) O6.35 6 1/4-36UNS-2A All dimensions: mm Note:When mating with corresponding part (W.FL2-RSMT-1) must be pressed down and held to make complete connection. Part No. HRS No. Packaging RoHS HRMJ-W.FL2P-ST3 311-0417-0 1 Yes Receptacle Inspection Adapter (W.FL2/W.FL) Used for inspecting the performance parameters of the cable assembly. 12.1 (7.9) (4.4) 4.2 1 7HEX M50.5 All dimensions: mm 6 Part No. HRS No. Packaging RoHS W.FL-R-1 331-0483-9 1 Yes W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height BTools Plug - Mating (Space saving type) This tool is used for mating a plug. 8 O10 (100) Part No. HRS No. RoHS W.FL-LP-IN 331-0323-2 Yes Note: Can be used with W.FL, X.FL plugs. Plug - Mating /Unmating (W.FL2-LP-040HF/032HF) This tool is for mating and unmating a plug. Unmating end 10 Mating end 2 (60) Part No. HRS No. RoHS W.FL2-LP-IN.OUT 331-0321-7 Yes Plug-Mating/Unmating (W.FL2-LP-062HF) This tool is for mating and unmating W.FL2-LP-062HF plug. JcbVi^c\ZcY M#;ABVg^c\ M#;A &% BVi^c\ZcY ' +% Part No. HRS No. RoHS X.FL-LP-IN.OUT1 331-0715-2 Yes Note: Can be used with X.FL plug. 7 W.FL2 SeriesUltra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height Precautions 1. Plugs (1) Mating / Unmating q To disconnect connectors, insert the extraction side of insertion and extraction jig and perform as described in the diagram below. Use of the extraction tool is absolutely mandatory. Any attempt of unmating by pulling on the cable may result in damage and affect the mechanical / electrical performance. * Unmating Insert the extraction side of the Tilt the tool as shown : tool under the mated plug at the @ and lift the plug cable cable connection side (as shown). Removal completed assembly. * Mating q Align the mating axes of the plug and the receptacle. w Confirm that the plug is positioned to be guided. (The both axes are aligned and the plug is positioned stably.) e Remove the tool by carefully pulling it up. : @ . L#;A'"AE"Eaj\ Eaj\e^Xje (2) P u l l f o r c e s o n t h e cable after connectors are mated ; = L#;A'"G"HBI"& GZbdkVad[ i]Zidda >chZgiidgZXZeiVXaZ L#;A'"AE" Do not apply any pull forces after the bending of the cable. 'CbVm# %+'%)%ineZ &CbVm# %('ineZ L#;A'"G"HBI"& (3) Precautions Do not twist connectors excessively during mating / unmating. 2. Receptacles (1) Recommended reflow temperature profile [c] 260 240 220 200 180 160 140 120 100 80 250 c max. for 10 seconds Preheat (130 to 180c) 120 seconds max. 230c 220c 50 seconds max. 60 seconds max. Time q The temperature of the printed circuit board surface temperature at the points of contact with the terminals. w Reflow soldering should be performed at a printed circuit surface temperature of 250C max. e In individual applications the actual temperature may vary, depending on the solder paste type, volume / thickness and board size / thickness. Consuly your solder paste and equipment manufacturer for specific recommendations. (2) Recommended metal mask thickness 0.1 mm to 0.12 mm (3) Reflow cycles 2 times 3. Operating environment and storage conditions (1) Operating environment The connectors are not designed to operate in the following environments: * Exposed to a excessive amounts of fine particles and dust * Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gasses. * Environments having large rapid variations in temperature. (2) Storage conditions Receptacle Store in the Hirose Electric packaging. Temperature: -10 to +40c, Humidity: 85% max. Use within 6 months of delivery. Receptacles for which the storage period has elapsed must be tested for solderability to the PC board mounting surface. (R) 8 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 11/2014. Contents are subject to change without notice for the purpose of improvements. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Hirose Electric: W.FL-2LP-04N1-A-(400) W.FL-2LP-04N1-A-(180) W.FL-2LP-04N1-A-(800) W.FL-2LP-04N1-A-(240) W.FL-2LP04N1-A-(220) W.FL-2LP-04N1-A-(260) W.FL-2LP-04N1-A-(600) W.FL-2LP-04N1-A-(110) W.FL-2LP-04N1-A-(150) W.FL-2LP-04N1-A-(130) W.FL-2LP-04N1-A-(170) W.FL-2LP-04N1-A-(160) W.FL-2LP-04N1-A-(120) W.FL-2LP-04N1A-(290) W.FL-2LP-04N1-A-(900) W.FL-2LP-04N1-A-(190) W.FL-2LP-04N1-A-(200) W.FL-2LP-04N1-A-(230) W.FL2LP-04N1-A-(270) W.FL-2LP-04N1-A-(280) W.FL-2LP-04N1-A-(140) W.FL-2LP-04N1-A-(300) W.FL-2LP-04N1-A(700) W.FL-2LP-04N1-A-(60) W.FL-2LP-04N2-A-(90) W.FL-2LP-04N2-A-(70) W.FL-2LP-04N2-A-(40) W.FL-2LP04N1-A-(80) W.FL-2LP-04N1-A-(40) W.FL-2LP-04N1-A-(50) W.FL-2LP-04N2-A-(35) W.FL-2LP-04N2-A-(50) W.FL2R-SMT-1(10) W.FL-2LP-04N2-A-(60) W.FL-2LP-04N2-A-(80) W.FL-2LP-04N1-A-(250) W.FL-2LP-04N1-A-(70) W.FL2LP-04N1-A-(90) W.FL-2LP-04N2-A-(300) W.FL-2LP-04N2-A-(130) W.FL-2LP-04N2-A-(700) W.FL-2LP-04N2-A-(150) W.FL-2LP-04N2-A-(110) W.FL-2LP-04N2-A-(190) W.FL-2LP-04N2-A-(170) W.FL-2LP-04N1-A-(35) W.FL-2LP-04N2A-(1000) W.FL-2LP-04N2-A-(180) W.FL-2LP-04N2-A-(600) W.FL-2LP-04N2-A-(400) W.FL-2LP-04N2-A-(800) W.FL2LP-04N2-A-(140) W.FL-2LP-04N2-A-(120) W.FL-2LP-04N2-A-(160) W.FL-2LP-04N2-A-(500) W.FL-2LP-04N2-A(200) W.FL-2LP-04N2-A-(900) W.FL-2LP-04N1-A-(100) W.FL-2LP-04N1-A-(1000) W.FL-2LP-04N1-A-(500) W.FL2LP-04N2-A-(100) W.FL2-2LP-04N2-A-(300) W.FL2-2LP-04N1-A-(400) W.FL2-2LP-04N1-A-(200) W.FL2-2LP-04N2A-(150) W.FL2-2LP-04N1-A-(50) W.FL2-2LP-04N2-A-(200) W.FL2-2LP-04N1-A-(150) W.FL2-2LP-04N1-A-(300) W.FL2-2LP-04N2-A-(400) W.FL2-2LP-04N1-A-(500) W.FL2-R-SMT-1(60) W.FL2-R-SMT-1(40) W.FL2-R-SMT-1(80)