SPC-MR-EIR-1291-TNA - Source Photonics, Inc.

- 1 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Features

 Single 3.3V Supply

 Duplex LC Connector

 30km/60km (1271~1451nm/1471~1611nm) Reach

 20dB Minimum, 24 dB Typical Link Budget

 Commercial Temperature Available

 Industrial Temperature Available

 CWDM Wavelength, DFB Laser

 SFP MSA SFF-8074i Compliant

 GR 253/STM G.957 Compliant

 Digital Diagnostic SFF-8472 Compliant

 Telcordia GR-468 Compliant

 RoHS Compliant

Table 1 – General Operating

Parameter Symbol Min. Typical Max. Unit Notes

Supply Voltage Vcc 3.135 3.3 3.465 V

Total Current, -40 to -5 ºC ICC - - 500 mA 1

Total Current, -5 to 85 ºC ICC - - 300 mA

Power Supply Noise Rejection PSR 100 - - mVp-p 2

Operating Temperature (Case) Topr -5 - 70 ºC 3

Operating Temperature (Case) Topr -40 - 85 ºC 3

Storage Temperature Tstg -40 - 85 ºC

Data Rate DR 100 - 2700 Mbps

Note 1: Denotes deviation from MSA

Note 2: 20Hz to 155MHz

Note 3: Please refer to ordering information

Table 2 – Transmitter Specifications (Optical)

Parameter Symbol Min. Typical Max. Unit Notes

Optical Power Pop 0 2 5 dBm

Average Launch Power Tx_Off Poff - - -45 dBm

Extinction Ratio ER 9 - - dB

Eye Mask IEEE 802.3ah, SONET/SDH Compliant

Optical Jitter Generation Jgen - - 0.007 UI

Optical Rise/Fall Time tr/tf - - 160 ps 4

Mean Wavelength λ 1xx1-6.5 1xx1 1xx1+6.5 nm

Spectral Width (20dB) Δλ - - 1 nm

Dispersion Penalty (60km) dp - 1 1.5 dB 5

Relative Intensity Noise RIN - - -120 dB/Hz

- 2 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Reflection Tolerance rp -24 - - dB 6

Note 4: 20%~80% values

Note 5: Measured at BER of 10-12, PRBS of 223-1,at eye center

Note 6: 1 dB degradation of receiver sensitivity

Table 3 – Transmitter Spe cifications (Electrical)

Parameter Symbol Min. Typical Max. Unit Notes

Input Differential Impedence Rin 80 100 120 Ω

PECL Single Ended Data Input Swing Vin, p-p 250 - 1200 mV

TxFault_Fault Vfault 2 - Vcc V

TxFault_Normal Vnormal Vee - Vee + 0.5 V

TxDisable_Disable Vd 2 - Vcc V

TxDisable_Enable Ven Vee - Vee + 0.8 V

Table 4 – Receiver Specifications (Optical)

Parameter Symbol Min. Typical Max. Unit Notes

Receiver Power Low Rsens,low - -22 -20 dBm 7

Receiver Power High Rsens,high 0 - - dBm 7

Damage Threshold For Receiver Pin, damage 5 - - dBm

Wavelength λ 1200 - 1625 nm

Maximum Reflectance Of Receiver RX_r - - -27 dB

LOS Assert - -30 - - dBm 8

LOS Assert - -38 - - dBm 9

LOS De-Assert - - - -20 dBm

LOS Hysteresis - 0.5 - - dB

Note 7: 10-10 BER, PRBS 223-1, OC-48 for SONET; 10-12 BER, PRBS 27-1, for Gigabit Ethernet

Note 8: SPC-MR-EIR-xxCxA options

Note 9: SPC-MR-EIR-xxTxA options

Table 5 – Receiver Specifications (Electric al)

Parameter Symbol Min. Typical Max. Unit Notes

PECL Single Ended Data Output Swing Vout, p-p 185 - 800 mV

Data Output Rise/Fall Time tr/tf - - 175 ps

- 3 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Table 6 – Timing and Electrical

Parameter Symbol Min. Typical Max. Unit Notes

Tx Disable Negate Time t_on - - 1 ms

Tx Disable Assert Time t_off - - 10 µs

Time to Initialize, Including Reset of Tx

Fault t_init - - 300 ms

Tx Fault Assert Time t_fault - - 100 µs

Tx Disable to Reset t_reset 10 - - µs

LOS Assert Time t_loss_on - - 100 µs

LOS De-Assert Time t_loss_off - - 100 µs

Serial ID Clock Rate f_serial_clock - - 100 kHz

RX_LOS Voltage (High) Rx_LOSH 2 - - V

RX_LOS Voltage (Low) RX_LOSL - - 0.8 V

LOS Output Voltage-Fault VLOS fault 2 - Vcc V

LOS Output Voltage-Normal VLOS normal Vee - Vee + 0.5 V

MOD_DEF (0:2)-High VH 2 - Vcc V

MOD_DEF (0:2)-Low VL V

ee - Vee + 0.5 V

Table 7 – Diagnostics

Parameter Range Accuracy Unit Calibration Formula

Temperature (-CDA) -5 to 70 ±3 ºC External

Tc(C) = Tslope*Tad(16 bit signed twos

complement value) + Toffset

Temperature (-TDA) -40 to 85 ±3 ºC External

Tc(C) = Tslope*Tad(16 bit signed twos

complement value) + Toffset

Voltage 0 to Vcc 0.1 V External V(Volts) = Vslope*Vad (16 bit unsigned

integer) + Voffset

Bias Current 0 to 120 5 mA External I(mA) = Islope * Iad(16 bit unsigned integer)

+ Ioffset

Tx Power 0 to +5 ±3 dBm External Tx_PWR(µW) = Tx_PWRslope*Tx_PWRad

(16 bit unsigned integer)+Tx_PWRoffset

Rx Power -20 to 0 ±3 dBm External Rx_PWR(µW) =

A0+A1*x+A2*x^2+A3*x^3+A4*x^4

- 4 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Table 8 – EEPROM Serial ID (A0h)

Name of Field Description of Field Address Hex ASCII

Identifier Type of serial transceiver 0 03

Ext. Identifier Extended identifier of type of serial transceiver 1 04

Connector Code for connector type 2 07

3 04

4 12/0A

5 22

6 02

7 10

8 10

9 01

Transceiver

Code for electronic compatibility or optical

compatibility

Byte 4:

12(hex), wavelength 1271~1451nm, 30km

0A(hex), wavelength 1471~1611nm, 60km

10 05

Encoding Code for serial encoding algorithm 11 05

BR.Nominal Units of 100 MBits/sec. 12 19

Reserved Reserved 13 00

Length (9µm,km) 9/125 µm fiber, units of km

30km: 1E(hex), 60km: 3C(hex) 14 1E/3C

Length (9µm) 9/125 µm fiber, units of 100 m 15 FF

Length (50µm) 50/125 µm fiber, units of 10 m 16 00

Length (62.5µm) 62.5/125 µm fiber, units of 10 m 17 00

Length (Copper) Units of meters 18 00

Reserved Reserved 19 00

20 53 S

21 4F O

22 55 U

23 52 R

24 43 C

25 45 E

26 50 P

27 48 H

28 4F O

29 54 T

30 4F O

31 4E N

32 49 I

33 43 C

34 53 S

Vendor Name SFP vendor name (ASCII)

35 20

[

ace

]

- 5 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Table 8 – EEPROM Serial ID (A0h)

Name of Field Description of Field Address Hex ASCII

Reserved Reserved 36 00

37 00

38 1F

Vendor OUI

IEEE vendor OUI code for

Source Photonics Inc. 39 22

40 53 S

41 50 P

42 43 C

43 4D M

44 52 R

45 45 E

46 49 I

47 52 R

48 34 4

49 37 7

50 43 C

51 44 D

52 41 A

53 20 [Space]

54 20 [Space]

Vendor P/N Part number in ASCII, e.g.

SPCMREIR47CDA

55 20 [Space]

56 41 A

57 20 [Space]

58 20 [Space]

Vendor Rev. Revision level for part number provide by

vendor (ASCII)

59 20 [Space]

60 xx

Wavelength CWDM wavelength

61 xx

Reserved Reserved 62 00

CC_BASE Check code for Base ID Fields

(addresses 0 to 62) 63 xx

64 00

Options Indicates which optional transceiver signals

are implemented 65 1A

- 6 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Table 8 – EEPROM Serial ID (A0h)

Name of Field Description of Field Address Hex ASCII

BR, max Upper bit rate margin, unit of % 66 08

BR, min Lower bit rate margin, unit of % 67 60

Vendor S/N Serial number 68-83 xx

Date Code Vendor’s manufacturing date code 84-91 xx

Diagnostic Monitoring

Type

Indicates which type of diagnostic monitoring

is implemented in the transceiver 92 58

Enhanced Options Indicates which optional enhanced features

are implemented in the transceiver 93 B0

SFF-8472 Compliance Indicates which revision of SFF-8472 the

transceiver complies with 94 02

CC_EXT Check code for Extended ID Fields

(addresses 64 to 94) 95 xx

Vendor Specific Vendor Specific EEPROM 96-127 xx

Table 9 –λc W av elength Guide

Code λc Unit Code λc Unit Code λc Unit

27 1271 nm 39 1391 nm 51 1511 nm

29 1291 nm 41 1411 nm 53 1531 nm

31 1311 nm 43 1431 nm 55 1551 nm

33 1331 nm 45 1451 nm 57 1571 nm

35 1351 nm 47 1471 nm 59 1591 nm

37 1371 nm 49 1491 nm 61 1611 nm

- 7 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Table 10 – Pin Definitions

Pin Unit Notes

1 VeeT TX GND

2 TX_FAULT Open Collector

3 TX_DISABLE Internally Pulled High

4 MOD_DEF2 Serial Data Input

5 MOD_DEF1 Serial Clock Input

6 MOD_DEF0 Internally Grounded

7 NC Not Connected

8 LOS Open Collector

9 VeeR RX Ground

10 VeeR RX Ground

11 VeeR RX Ground

12 RXD- RX Data Negative

13 RXD+ RX Data Positive

14 VeeR RX GND

15 VCCR RX Power

16 VCCT TX Power

17 VeeT TX GND

18 TXD+ TX Data Positive

19 TXD- TX Data Negative

20 VeeT TX GND

- 8 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Recommended Interface Circuit

Protocol IC

SerDes

Laser Driver

Receiver Amplifier

EEPROM

SourcePhotonics

SFP

R1R1R1

Vcc

R1=4.7K to 10K Ω

MOD_DEF 0

MOD_DEF 1

MOD_DEF 2

VeeR

RX_LOS

RD -

RD +

0.1μF10μF

VCCR

RX_LOS

100Ω

.01μF

10KΩ

VccT

Vcc

VCCT

TD -

TD +

.01μF

100Ω

TX_FAULT

TX_DISABLE

1μH

0.1μF

10μF

TX_FAULT

TX_DISABLE

- 9 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Mechanical Diagram

Units in mm(inch)

- 10 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Order Information

Table 11 – Order Information

Part No.

SPC-MR-EIR-xxCDA

SPC-MR-EIR-xxCNA

SPC-MR-EIR-xxTDA

SPC-MR-EIR-xxTNA

Part Numbering Definition:

SPC - MR - EIR - xx Temperature Diagnostic Revision

● SPC = Small Form Pluggable CWDM

● Data Rate

MR = Multi Rate, 100~2700Mbps

● EIR = IEEE802.3ah Interface 30/60km

● xx = CWDM Wavelength (1271nm~1611nm)

● Operating Temperature

C = Commercial Temperature (-5 to 70℃)

T = Industrial Temperature (-40 to 85℃)

● Diagnostic

D = Digital Diagnostic (SFF-8472)

N = No Digital Diagnostic

● Design Revision

A = RoHS Compliant

- 11 -

SPC-MR-EIR-xx

Multi

Rate CWDM

SFP Transceiver

DS-5579 Rev 0.1 2009-07-08

Warnings

Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static

free environment is highly recommended. Follow guidelines according to proper ESD procedures.

Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or

indirect radiation.

Legal Notice

IMPORTANT NOTICE!

All information contained in this document is subject to change without notice, at Source Photonics’ sole and

absolute discretion. Source Photonics warrants performance of its products to current specifications only in

accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary”

are given to describe components only, and Source Photonics expressly disclaims any and all warranties for said

products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular

purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for

further warranty information.

Source Photonics assumes no liability for applications assistance, customer product design, software performance,

or infringement of patents, services, or intellectual property described herein. No license, either express or implied,

is granted under any patent right, copyright, or intellectual property right, and Source Photonics makes no

representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual

property rights. Products described in this document are NOT intended for use in implantation or other life support

applications where malfunction may result in injury or death to persons. Source Photonics customers using or

selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Source

Photonics for any damages resulting from such use or sale.

THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees

that Source Photonics is not liable for any actual, consequential, exemplary, or other damages arising directly or

indirectly from any use of the information contained in this document. Customer must contact Source Photonics to

obtain the latest version of this publication to verify, before placing any order, that the information contained herein is

current.

Contact

U.S.A. Headquarters

20550 Nordhoff Street

Chatsworth, CA 91311

USA

Tel: +1-818-773-9044

Fax: +1-818-773-0261

sales@sourcephotonics.com

China

Building #2&5, West Export Processing Zone

No. 8 Kexin Road, Hi-Tech Zone

Chengdu, 611731, China

Tel: +86-28-8795-8788

Fax: +86-28-8795-8789

sales@sourcephotonics.com.cn

Taiwan

9F, No 81, Shui Lee Rd.

Hsinchu, 300, Taiwan

R.O.C.

Tel: +886-3-5169222

Fax: +886-3-5169213

sales@sourcephotonics.com.tw