Document No. U14889EJ3V0UM00 (3rd edition)
Date Published October 2003 N CP(K)
Printed in Japan
User’s Manual
IE-78K0-NS-A
In-Circuit Emulator
Target Devices
78K/0 Series
©
User’s Manual U14889EJ3V0UM
2
[MEMO]
User’s Manual U14889EJ3V0UM 3
Windows NT is either a registered trademark or a trademark of Microsoft Corporation in the United States
and/or other countries.
PC/AT is a trademark of International Business Machines Corporation.
The information in this document is current as of September, 2003. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-
designated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
•
•
•
•
•
•
M8E 02 . 11-1
(1)
(2)
"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
"NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
"Standard":
"Special":
"Specific":
User’s Manual U14889EJ3V0UM
4
Regional Information
• Device availability
• Ordering information
• Product release schedule
• Availability of related technical literature
• Development environment specifications (for example, specifications for third-party tools and
components, host computers, power plugs, AC supply voltages, and so forth)
• Network requirements
In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary
from country to country.
[GLOBAL SUPPORT]
http://www.necel.com/en/support/support.html
NEC Electronics America, Inc. (U.S.)
Santa Clara, California
Tel: 408-588-6000
800-366-9782
NEC Electronics Hong Kong Ltd.
Hong Kong
Tel: 2886-9318
NEC Electronics Hong Kong Ltd.
Seoul Branch
Seoul, Korea
Tel: 02-558-3737
NEC Electronics Shanghai, Ltd.
Shanghai, P.R. China
Tel: 021-6841-1138
NEC Electronics Taiwan Ltd.
Taipei, Taiwan
Tel: 02-2719-2377
NEC Electronics Singapore Pte. Ltd.
Novena Square, Singapore
Tel: 6253-8311
J03.4
N
EC Electronics (Europe) GmbH
Duesseldorf, Germany
Tel: 0211-65 03 01
• Sucursal en España
Madrid, Spain
Tel: 091-504 27 87
Vélizy-Villacoublay, France
Tel: 01-30-67 58 00
• Succursale Française
• Filiale Italiana
Milano, Italy
Tel: 02-66 75 41
• Branch The Netherlands
Eindhoven, The Netherlands
Tel: 040-244 58 45
• Tyskland Filial
Taeby, Sweden
Tel: 08-63 80 820
• United Kingdom Branch
Milton Keynes, UK
Tel: 01908-691-133
Some information contained in this document may vary from country to country. Before using any NEC
Electronics product in your application, pIease contact the NEC Electronics office in your country to
obtain a list of authorized representatives and distributors. They will verify:
User’s Manual U14889EJ3V0UM 5
INTRODUCTION
Product overview The IE-78K0-NS-A is used in combination with an emulation board (IE-780×××-NS-
EM1, IE-780×××-NS-EM4) and I/O board (IE-78K0-NS-P0×) to debug products in the
78K/0 Series of 8-bit single-chip microcontrollers.
Target readers This manual is intended for engineers who perform debugging of systems that employ
78K/0 Series 8-bit single-chip microcontrollers using the IE-78K0-NS-A and an
emulation board (IE-780×××-NS-EM1, IE-780×××-NS-EM4) and I/O board (IE-78K0-NS-
P0×).
Purpose The purpose of this manual is to help the user understand the debugging functions that
are available by using the IE-78K0-NS-A and the emulation board (IE-780×××-NS-EM1,
IE-780×××-NS-EM4) and I/O board (IE-78K0-NS-P0×) together.
Organization When using the IE-78K0-NS-A, please refer to the manual that comes with the IE-78K0-
NS-A (this manual) as well as the manual that comes with the emulation board (IE-
780×××-NS-EM1, IE-780×××-NS-EM4) and I/O board (IE-78K0-NS-P0×).
• Basic specifications • Function outline
• System configuration • Target interface differences
• External interface function
How to read this manual To understand the overall functions of the IE-78K0-NS-A:
→ Read this manual in the order of the contents.
To understand the basic specifications:
→ Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES.
For how to connect the IE-780×××-NS-EM1, IE-780×××-NS-EM4, and IE-78K0-NS-P0×
and make settings to debug 78K/0 Series products:
→ Refer to CHAPTER 3 INSTALLATION.
IE-78K0-NS-A
User’s Manual
(This manual)
IE-780×××-NS-EM1
IE-780×××-NS-EM4
IE-78K0-NS-P0×
User’s Manual
User’s Manual U14889EJ3V0UM
6
Terminology The meanings of the terms used in this manual are described in the table below.
Term Meaning
Emulation device This is a general term that refers to the device in the emulator that is used to
emulate the target device. It includes the emulation CPU.
Emulation CPU This is the CPU block in the emulator that is used to execute user-generated
programs.
Target device This is the device to be emulated.
Target program This is the program to be debugged.
Target system This is the system to be debugged.
This includes the target program and the hardware provided by the user.
When defined narrowly, it includes only the hardware.
Conventions Data significance: Higher digits on the left and lower digits on the right
Note: Footnote for item marked with Note in the text
Caution: Information requiring particular attention
Remark: Supplementary information
Related Documents Please use the following documents in conjunction with this manual.
The related documents listed below may include preliminary versions. However,
not marked as such.
Documents Related to Development Tools (User’s Manuals)
Document Name Document Number
IE-78K0-NS-A In-Circuit Emulator This manual
Operation U16629E
Language U14446E
RA78K0 Assembler Package
Structured Assembly Language U11789E
Operation U16613E CC78K0 C Compiler
Language U14298E
SM78K Series Ver.2.52 System Simulator Operation U16768E
SM78K Series Ver.2.30 or Later System Simulator External part user open interface specifications U15802E
ID78K0-NS Ver.2.52 Integrated Debugger Operation U16488E
Fundamental U11537E 78K/0 Series Real-Time OS (RX78K0)
Installation U11536E
PM plus Ver.5.10 or Later U16569E
PG-FP4 Flash Memory Programmer U15260E
Caution The documents listed above are subject to change without notice. Be sure to use the latest
documents for designing, etc.
User’s Manual U14889EJ3V0UM 7
CONTENTS
CHAPTER 1 GENERAL ............................................................................................................................8
1.1 System Configuration...................................................................................................................8
1.2 Hardware Configuration .............................................................................................................10
1.3 Basic Specifications ...................................................................................................................13
1.4 Contents in Carton......................................................................................................................15
CHAPTER 2 PART NAMES ...................................................................................................................17
2.1 Parts of Main Unit .......................................................................................................................17
2.2 Board Names...............................................................................................................................19
2.3 External Sense Probe Names ....................................................................................................23
CHAPTER 3 INSTALLATION .................................................................................................................24
3.1 Connection ..................................................................................................................................24
3.2 External Trigger Functions ........................................................................................................36
3.3 External sense.............................................................................................................................36
3.4 Jumper Settings (on Main Board (G-780009 Board and G-780009a Board)) ........................37
3.5 Low-Voltage Emulation Settings...............................................................................................39
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC ...............................40
A.1 Introduction .................................................................................................................................40
A.2 Installation ...................................................................................................................................41
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) ................................................................42
B.1 Introduction .................................................................................................................................42
B.2 Installation ...................................................................................................................................43
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES .............................44
C.1 Introduction .................................................................................................................................44
C.2 Installation ...................................................................................................................................45
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES ..47
D.1 Introduction .................................................................................................................................47
D.2 Installation ...................................................................................................................................48
APPENDIX E REVISION HISTORY .......................................................................................................50
User’s Manual U14889EJ3V0UM
8
CHAPTER 1 GENERAL
The IE-78K0-NS-A is a development tool for effectively debugging hardware and software in which a 78K/0 Series
8-bit single-chip microcontroller is used.
This chapter describes the system configuration and basic specifications of the IE-78K0-NS-A.
1.1 System Configuration
Figure 1-1 shows the system configuration of the IE-78K0-NS-A.
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM 9
Figure 1-1. IE-78K0-NS-A System Configuration
Host machine
PC-9800 series
or IBM PC/AT
TM
and compatibles
Integrated debugger
ID78K0-NS
(sold separately)
Device file
Note 3
(available separately)
Control software
Interface board
IE-70000-98-IF-C
(sold separately)
Interface board
IE-70000-PC-IF-C
(sold separately)
Interface board
IE-70000-PCI-IF-A
(sold separately)
or
IE-78K0-NS-A
(this product)
I
nterface cable
(NS interface cable)
In-circuit emulator
PC card interface
Interface cable
NS card
cable MC card
cable
Note 5
PC card interface
IE-70000-CD-IF-A
(sold separately)
AC adapter
IE-70000-MC-PC-B
(sold separately)
Emulation board
IE-780×××-NS-EM1
(sold separately)
Emulation probe
NP-×××××
Note 2
(sold separately)
Conversion socket
EV-××××G-××
TG×-××××××
Note 4
(sold separately)
+
I/O board
IE-78K0-NS-P0×
(sold separately)
Emulation board
IE-780×××-NS-EM4
Note 1
(sold separately)
+
+
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM
10
Notes 1. When using the IE-780×××-NS-EM4, it is necessary to connect an I/O board, the IE-78K0-NS-P0×. The
IE-780×××-NS-EM4 and IE-78K0-NS-P0× are sold separately.
2. The NP-××××× is a product of Naito Densei Machida Mfg. Co., Ltd.
For further information, contact Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191)
3. The device file can be downloaded from the NEC Electronics Website
(URL: http://www.necel.com/micro/).
4. The TG×-×××××× is a product of TOKYO ELETECH CORPORATION.
Contact: Daimaru kogyo, Ltd. Tokyo Electronic Division (TEL: +81-3-3820-7112)
Osaka Electronic Division (TEL: +81-6-6244-6672)
5. This is not used for the IE-78K0-NS-A.
1.2 Hardware Configuration
The IE-78K0-NS-A consists of the following hardware units (such as cabinet and boards).
There are two kinds of board configuration for the IE-78K0-NS-A, a two-board (the 78K0 main board and the 78K0
performance board) type and a one-board (a combined 78K0 main board and 78K0 performance board) type.
The board type can be distinguished by the 2nd figure from the left in the serial number. F or earlier indicates the
two-board type and G or later indicates the one-board type.
(1) Two-board type (when the 2nd figure from the left in the serial number is F or earlier.)
• Cabinet
• 78K0 main board (G-780009 Board)
• 78K0 performance board (G-78K0H OPTION Board)
Figure 1-2. IE-78K0-NS-A (Two-Board Type) Basic Hardware Configuration 1-1
IE-78K0-NS-A
78K0
performance
board
78K0 Series
EM1 board
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated bus
interface
78K0
main board
(G-780009
Board)
External sense
probe
Emulation probe
(sold separately)
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM 11
Figure 1-3. IE-78K0-NS-A (Two-Board Type) Basic Hardware Configuration 1-2
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated bus
interface
78K0
main board
(G-780009
Board)
78K0
performance
board
I/O board
(IE-78K0
-NS-P0×)
78K0 Series
EM4 board
Emulation probe
(sold separately)
External sense
probe
IE-78K0-NS-A
(2) One-board type (when the 2nd figure from the left in the serial number is G or later)
• Cabinet
• 78K0 main board (G-780009 Board)Note
Note This board is different than the previous 78K0 main board in (1)
Figure 1-4. IE-78K0-NS-A (One-Board Type) Basic Hardware Configuration 2-1
78K0
main board
(G-780009a
Board)
IE-78K0-NS-A
78K0
Series
EM1 board
Host
machine
Interface board
(sold separately)
Interface board
(sold separately)
Dedicated bus
interface
Emulation probe
(sold separately)
External sense
probe
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM
12
Figure 1-5. IE-78K0-NS-A (One-Board Type) Basic Hardware Configuration 2-2
78K0
main board
(G-780009a
Board)
I/O board
(IE-78K0
-NS-P0×)
78K0
Series
EM4 board
IE-78K0-NS-A
Host
machine
Interface
board
(sold
separately)
Interface
board
(sold
separately)
Dedicated bus
interface
Emulation probe
(sold separately)
External sense
probe
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM 13
1.3 Basic Specifications
Table 1-1. List of Functions (MAX. Specifications) (1/2)
Parameter Description
Supervisor V40 (operating frequency: 16.0 MHZ)
Target device 78K/0 Series (
µ
PD780×××)
System clock According to specification of emulation board (sold separately)
External Pulse input Clock supply
Internal Mounted on emulation board (sold separately)
Substitute memory capacity 64 KB
Internal ROM 4 KB
Internal high-speed
RAM 64 bytes
Internal low-speed
RAM 128 bytes
Mapping
unit
External expansion
memory 8 KB
Emulation function • Real-time execution
• Break execution
• Step execution
Real-time internal RAM monitor 2 KB of memory space
Event detection • Program execution detection (fetch): 10 (BRS1 to BRS10)
• Bus event detection (access): 12 (BRA1 to BRA12)
Event integration • External trigger detection
Trigger output (open-drain output (1))
• Path condition (BRS1, BRS2, or BRA1 to BRA4)
• Trace qualify condition (BRA1 to BRA4)
• Delay condition
• Trigger condition (BRS1, BRS2, or BRA1 to BRA4)
Break factors • Event break
• Manual break
• Command break
• Fail-safe break
• External single event inputs (8)
• Time out break
Trace factors • All traces
• Qualify trace (access only)
• Section trace (both fetch and access) (interevent trace)Note
Trace capacity 80 bits × 8 KB
Real-time trace
Trace content Address, data, status, 16 external sense traces (8 of which (EXTCN1) can be used as
external single event inputs), time stamp, and snap shot
Note Events use BRS3 to BRS10 and BRA5 to BRA12.
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM
14
Table 1-1. List of Functions (MAX. Specifications) (2/2)
Parameter Description
Execution time measurement Up to 4 min 28 s, resolution: 62.5 ns
Interevent time measurement
• Resolution: Changeable between 160 ns and 20.56
µ
s
• Maximum measurement timeNote
When resolution is set to 160 ns: Approximately 11 minutes
When resolution is set to 20.56
µ
s: Approximately 24 hours
Coverage Between 64 KB (read, write, fetch)
DMM 16 eventsNote
Target interface Emulation probe (sold separately) provided for each target device shape
Host interface Dedicated bus interface
Low-voltage support Based on the emulation board (sold separately)
Host machine PC-9800 series, or IBM PC/AT and compatibles
Power supply DC 5 V
Operation temperature range 10°C to 40°C
Operation humidity range 0% to 80% (no condensation)
Dimensions W240 × D197 × H73 (mm)
Note Events use BRS3 to BRS10 and BRA5 to BRA12.
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM 15
1.4 Contents in Carton
The IE-78K0-NS-A carton contains the main unit, cables, an accessory bag, and a guarantee card.
Make sure that the accessory bag contains a packing list, this user’s manual, spacers, and screws.
In the case of missing or damaged items, please contact an NEC sales representative or NEC distributor.
Figure 1-6. Contents in Carton
<2> NS interface cable
<3> FG cable
<1> IE-78K0-NS-A
<7> Guarantee card
<6> Accessory bag
<4> External sense probe
<5> External sense clip
<1> IE-78K0-NS-A main unit × 1
<2> NS interface cable × 1
<3> FG cable × 1
<4> External sense probes × 2
<5> External sense clips × 20 (10 per case × 2)
<6> Accessory bag × 1
<7> Guarantee card × 1
CHAPTER 1 GENERAL
User’s Manual U14889EJ3V0UM
16
Check that the accessory bag contains the following items
(1) Two-board Type (when the 2nd figure from the left in the serial number is F or earlier)
Refer to Figure 1-7 Contents in Accessory Bag (when the 2nd figure from the left in the serial number is F
or earlier).
<a> Packing list × 1
<b> User’s manual (this manual) × 1
<c> Metal spacers × 5
<d> Plastic spacers × 2
<e> Screws × 4
Figure 1-7. Contents in Accessory Bag, Two-Board Type
(When 2nd Figure from Left in Serial Number Is F or Earlier)
(a) Packing list
(b) User's manual
(e) Screws
(d) Plastic spacers
(c) Metal spacers
(2) One-board type (when the 2nd figure from the left side of the serial number is G or later)
Refer to Figure 1-8 Contents in Accessory Bag (when the 2nd figure from the left in the serial number is G
or later).
<a> Packing list × 1
<b> User’s manual (this manual) × 1
<c> Screws × 4
Figure 1-8. Contents in Accessory Bag, One-Board Type
(When 2nd Figure from Left in the Serial Number Is G or Later)
(c) Screws
(a) Packing list
(b) User's manual
User’s Manual U14889EJ3V0UM 17
CHAPTER 2 PART NAMES
This chapter introduces the parts of the IE-78K0-NS-A main unit.
The packing box contains the IE-78K0-NS-A main unit and accessories. If there are any missing or damaged
items, please contact an NEC sales representative.
Please make sure to fill out and return the guarantee card that comes with the main unit.
2.1 Parts of Main Unit
(1) Probe end
One-Board Type
Two-Board Type
T V C C
Target system power supply LED Probe interface
Small: 13 × 158 mm
Large: 16 × 158 mm
EXTCN1
EXTCN2 External sense probe socket
T V C C
Target system power supply LED Probe interface
Small: 13 × 158 mm
Large: 16 × 158 mm
EXTCN1
EXTCN2 External sense probe socket
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM
18
(2) Top view
POWER
IN CIRCUIT EMULATOR
Power supply LED
(3) Interface
FG OFF ON RESET HOST-I/F
DC IN
-+
Reset switch
(RESET)
Dedicated bus interface connector
(HOST-I/F)
Power switch
(OFF/ON)
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM 19
2.2 Board Names
The IE-78K0-NS-A contains the following boards.
(1) Two-board type (when the 2nd figure from the left in the serial number is F or earlier.)
• Main board (G-780009 Board) × 1
• Performance board (G-78K0H OPTION Board) × 1
(2) One-board type (when the 2nd figure from the left in the serial number is G or later.)
• Main board (G-780009a Board) × 1
Caution Do not connect the G-78K0H OPTION Board to the G-780009a Board in case a malfunction
may occur.
Remove the four screws from the sides of the main unit, and then open the top cover to check that you have
the correct boards.
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM
20
Figure 2-1. Main Board (G-780009 Board) (Two-Board Type)
Remark The main board is shown mounted in the main unit.
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM 21
Figure 2-2. Performance Board (G-78K0H OPTION Board) (Two-Board Type)
J1
CN6B
P2
CN7B
CN4B
CN5B
P1
EXTCN1 EXTCN2
CNJTAG1
CN6A
CN7A
CN4A
CN5A
< Part side >
< Soldering side >
IE-78K0-NS-A
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM
22
Figure 2-3. Main Board (G-780009a Board) (One-Board Type)
CHAPTER 2 PART NAMES
User’s Manual U14889EJ3V0UM 23
2.3 External Sense Probe Names
The IE-78K0-NS-A includes external sense probes and external sense clips.
(1) External sense probes: 2
Table 2-1. Correspondence Between Connector No. and Color of Cable
Connector No. 1 2 3 4 5 6 7 8 9 10
Color of cable Brown Red Orange Yellow Green Blue Purple Gray N.C. Black
The names of the external sense probes when they are connected to EXTCN1 and EXTCN2 are as follows.
Table 2-2. Bit Configuration When Connecting External Sense Probe to EXTCN1
Connector No. 1 2 3 4 5 6 7 8 9 10
External sense EXT1 EXT2 EXT3 EXT4 EXT5 EXT6 EXT7 EXT8 N.C. GND
Table 2-3. Bit Configuration When Connecting External Sense Probe to EXTCN2
Connector No. 1 2 3 4 5 6 7 8 9 10
External sense EXT9 EXT10 EXT11 EXT12 EXT13 EXT14 EXT15 EXT16 N.C. GND
Remark N.C.: No connection
(2) External sense clips: 20 (16 for external sense probe, 2 for GND, and 2 spares)
• Made by Sunhayato Corporation (2 sets of 10)
Connector No.
10
9
8
7
6
5
4
3
2
1
User’s Manual U14889EJ3V0UM
24
CHAPTER 3 INSTALLATION
This chapter describes how to connect the cables to the IE-78K0-NS-A and the mode settings.
3.1 Connection
Connect the following nine products, which are sold separately.
Refer to Figure 1-1 IE-78K0-NS-A System Configuration in CHAPTER 1 GENERAL for the system configuration
of the IE-78K0-NS-A.
• IE-70000-98-IF-C: Interface board (use cable included with IE-78K0-NS-A)
• IE-70000-PC-IF-C: Interface board (use cable included with IE-78K0-NS-A)
• IE-70000-PCI-IF-A: Interface board (use cable included with IE-78K0-NS-A)
• IE-70000-CD-IF-A: PC card interface (use NS card cable)
• IE-70000-MC-PS-B: AC adapter
• IE-780×××-NS-EM1: Emulation board
• IE-780×××-NS-EM4: Emulation board
• IE-78K0-NS-P0×: I/O board
• NP-×××××: Emulation probe
Caution Connecting and removing cables or components from the target system and changing the
settings of switches, etc. should be carried out after turning off the power of the IE-78K0-NS-A
main unit and the target system.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 25
(1) Two-board type (when the 2nd figure from the left in the serial number is F or earlier.)
(a) Connecting emulation board (IE-780×××-NS-EM1)
The IE-780×××-NS-EM1 is sold separately.
Figure 3-1. Connecting Emulation Board (IE-780×××-NS-EM1) (Two-Board Type) (1/2)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Fix the spacers (metal) included with the IE-
78K0-NS-A at five points on the board.
<4> Connect the IE-780×××-NS-EM1 to the
G-78K0H OPTION Board and fasten the
screws at the four corners.
<2> Remove the first and second plates from the
bottom by removing the screws.
Caution Only when connecting the IE-78018-
NS-EM1 on the G-78K0H OPTION
Board, remove spacer 1 (metal) of the
following figure and replace spacers 2
and 3 (metal) with the included
spacers (plastic).
<5> When using a probe, connect the probe.
IE-780×××-NS-EM1
G-78K0H OPTION Board
Refer to (3) for the probe
connection method.
Refer to (4) for the
external sense probe
connection method.
Here
G-78K0H OPTION Board
Included
spacer Included
spacer
Fix
Fix
Spacers 2 and 3
Spacer 1
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
26
Figure 3-1. Connecting Emulation Board (IE-780×××-NS-EM1) (Two-Board Type) (2/2)
<6> Replace the top cover and fasten the four
screws on the sides.
IE-780×××-NS-EM1
G-78K0H OPTION Board
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 27
(b) Connecting I/O board (IE-78K0-NS-P0×) and emulation board (IE-780×××-NS-EM4)
The IE-78K0-NS-P0× and IE-780×××-NS-EM4 are sold separately.
Figure 3-2. Connecting I/O Board and Emulation Board (IE-780×××-NS-EM4) (Two-Board Type) (1/2)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Fix the spacers (metal) included with the IE-
78K0-NS-A at five points on the board.
<5> Connect the IE-780×××-NS-EM4 on the IE-
78K0-NS-P0×, and fasten the screws at the
four corners.
<2> Remove the first and third plates from the
bottom by removing the screws.
<4> Connect the IE-78K0-NS-P0× on the G-
78K0H OPTION Board and fix the spacers
included with the IE-78K0-NS-P0× at the four
corners.
<6> When using a probe, connect the probe.
G-78K0H OPTION Board
IE-78K0-NS-P0×
G-78K0H OPTION Board
Included
spacer Included
spacer
Fix Fix
Here
Included
spacer
Included
spacer
FixFix
IE-780×××-NS-EM4
G-78K0H OPTION Board
IE-78K0-NS-P0×Refer to (3) for the probe
connection method.
Refer to (4) for the external sense
probe connection method.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
28
Figure 3-2. Connecting I/O Board and Emulation Board (IE-780×××-NS-EM4) (Two-Board Type) (2/2)
<7> Replace the top cover and fasten the four
screws on the sides.
IE-78K0-NS-P0×
G-78K0H OPTION Board
IE-780×××-NS-EM4
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 29
(2) One-board type (when the 2nd figure from the left in the serial number is G or later)
(a) Connecting emulation board (IE-780×××-NS-EM1)
The IE-780×××-NS-EM1 is sold separately.
Figure 3-3. Connecting Emulation Board (IE-780×××-NS-EM1) (One-Board Type) (1/2)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Connect the IE-780×××-NS-EM1 to the G-
780009a Board and fasten the screws at the
four corners.
<4> When using a probe, connect the probe.
<2> Remove the first plate from the bottom by
removing the screws.
Caution Remove the spacer 1 of the following
figure only when connecting the
IE-78018-NS-EM1.
<5> Replace the top cover and fasten the four
screws on the sides.
Refer to (3) for the probe
connection method.
Refer to (4) for the
external sense probe
connection method.
IE-780×××-NS-EM1
G-780009a Board
IE-780×××-NS-EM1
G-780009aBoard
Here Spacer1
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
30
(b) Connecting I/O board (IE-78K0-NS-P0×) and emulation board (IE-780×××-NS-EM4)
The IE-78K0-NS-P0× and IE-780×××-NS-EM4 are sold separately.
Figure 3-4. Connecting I/O Board and Emulation Board (IE-780×××-NS-EM4) (One-Board Type)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Connect the IE-78K0-NS-P0× on the G-
780009a board, and fix the spacers included
with the IE-78K0-NS-P0× at the four corners.
<5> When using a probe, connect the probe.
<2> Remove the second plate from the bottom by
removing the screws.
<4> Connect the IE-780×××-NS-EM4 on the IE-
78K0-NS-P0×, and fasten the screws at the
four corners.
<6> Replace the top cover and fasten the four
screws on the sides.
IE-78K0-NS-P0×
Included
spacer
Fix Fix
Included
spacer
G-780009a Board
IE-780×××-NS-EM4
IE-78K0-NS-P0×
G-780009aBoard
IE-78K0-NS-P0×
IE-780×××-NS-EM4
G-780009a Board
Refer to (3) for the probe
connection method.
Refer to (4) for the external sense
probe connection method.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 31
(3) Connecting emulation probe (NP-×××××)
The NP-××××× is sold separately.
(a) Two-board type (when the 2nd figure from the left in the serial number is F or earlier)
Figure 3-5. Connecting Emulation Probe (Two-Board Type)
Emulation probe
(NP-×××××)
IE-780×××-NS-EM1
Performance board
(G-78K0H OPTION Board)
Main board
(G-780009 Board)
Emulation probe
(NP-×××××)
IE-780×××-NS-EM4
I/O board
IE-78K0-NS-P0×
Main board
(G-780009 Board)
Performance board
(G-78K0H OPTION Board)
Caution The emulation probe (NP-×××××) mounting location varies depending on the model of the I/O
emulation board, IE-780×××-NS-EMn (n = 1 or 4) in use. For details, refer to the IE-780×××-NS-
EMn User’s Manual.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
32
(b) One-board type (when the 2nd figure from the left in the serial number is G or later)
Figure 3-6. Connecting Emulation Probe (One-Board Type)
IE-780×××-NS-EM1
Main board
(G-780009a Board)
Emulation probe
(NP-×××××)
IE-780×××-NS-EM4
I/O board
IE-78K0-NS-P0×
Main board
(G-780009a Board)
Emulation probe
(NP-×××××)
Caution The emulation probe (NP-×××××) mounting location varies depending on the model of the I/O
emulation board, IE-780×××-NS-EMn (n = 1 or 4) in use. For details, refer to the IE-780×××-NS-
EMn User’s Manual.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 33
(4) Connecting external sense probe
(a) Two-board type (when the 2nd figure from the left in the serial number is F or earlier)
Figure 3-7. Connecting External Sense Probe (Two-Board Type)
Performance board
(G-78K0H OPTION Board)
External sense probe (included × 2)
EXTCN1
EXTCN2
Ground line (black)
Ground line (black)
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
34
(b) One-board type (when the 2nd figure from the left in the serial number is G or later)
Figure 3-8. Connecting External Sense Probe (One-Board Type)
Main board
(G-780009a Board)
EXTCN1
Grand line (black) Grand line (black)
External sense probe (included × 2)
EXTCN2
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 35
(5) Connecting AC adapter (IE-70000-MC-PS-B)
IE-70000-MC-PS-B is sold separately.
<1> Insert the plug of the AC adapter (IE-70000-MC-PS-B) into the DC IN socket on the interface side of the IE-
78K0-NS-A.
Figure 3-9. Connecting AC Adapter
(6) Connecting interface cable
<1> Insert the cable into the bus interface connector on the IE-78K0-NS-A main unit.
Figure 3-10. Connecting Dedicated Bus Interface Cable
FG OFF ON RESET HOST-I/F
DC IN
-
+
Reset switch
(RESET)
Dedicated bus interface connector
(HOST-I/F)
Power switch
(OFF/ON)
Caution The type of interface cable varies depending on whether an interface board or a PC card
interface is used.
• When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF(-A))
→ Connect the NS interface cable included with the IE-78K0-NS-A.
• When using a PC card interface (IE-70000-CD-IF-A)
→ Connect the NS card cable included with the IE-70000-CD-IF-A.
The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF(-A), and IE-70000-CD-IF-A are sold
separately.
FG
Power switch
(ON/OFF)
Reset switch
(RESET)
OFF ON RESET HOST-I/F
Dedicated bus interface connector
(HOST-I/F)
DC IN
-
+
AC adapter
IE-70000-MC-PC-B
(sold separately)
AC input
80 V to 240 V
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
36
3.2 External Trigger Functions
(1) EXTOUT
At the occurrence of a break event, the EXTOUT pin on the emulation board outputs a low level for 1.3
µ
s.
Caution Because the output is open drain, connect a pull-up resistor in the target system.
(2) EXTIN
The EXTIN pin on the emulation board can be used to input an event signal. Enter high-level pulse signals for two
or more CPU clocks.
Caution For the electrical specifications, refer to Table 3-1.
Table 3-1. Electrical Specifications
Parameter MIN. [V] MAX. [V]
Input voltage, high Target voltage × 0.7 Target voltage
Input voltage, low 0 Target voltage × 0.3
3.3 External sense
Up to 16 bits of data can be input to the IE-78K0-NS-A from the target system via an external sense probe.
Also, when using an external sense break, input a level of at least 2 CPU clocks.
Table 3-2. Electrical Specifications of External Sense
Parameter MIN. [V] MAX. [V]
Input voltage, high Target voltageNote × 0.7 Target voltageNote
Input voltage, low 0 Target voltageNote × 0.3
Note 2.0 V when the target voltage is less than 2.0 V.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 37
3.4 Jumper Settings (on Main Board (G-780009 Board and G-780009a Board))
(1) Default jumper settings
Figure 3-11 shows the position of the jumpers used on the G-780009 Board and the G-780009a Board.
When changing the settings of jumpers on the G-780009 Board, remove the five spacers on the G-78K0H
OPTION Board, and then remove the G-78K0H-OPTION Board.
For details of the settings, refer to the user’s manual of each emulation board.
Figure 3-11. Default Settings of JP2, JP3, JP4, JP6, JP7, and JP8
135
24
JP6
6
123
JP2
123
JP3
123
JP4
135
24
JP8
6
135
24
JP7
6
JP8: Selection of the subsystem clock source (default setting: 1 and 2 shorted)
1 and 2 shorted: Internal (mounted on the emulation board or mounted on the parts board by
the user)
3 and 4 shorted: External (input via an emulation probe from the target system)
Cautions 1. Jumper settings differ depending on the emulation board. For details, refer to the
relevant emulation board user’s manual.
2. Set the jumpers on the G-780009 Board when the IE-78K0-NS-A, two-board type
(the 2nd figure from the left side of the serial number is F or earlier), is used.
Set the jumpers on the G-780009a Board when the IE-78K0-NS-A, one-board type
(the 2nd figure from the left side of the serial number is G or later), is used.
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM
38
Figure 3-12. Part Names of G-780009 Board
CN7
JP6
JP4
JP3
P2
CN6
JP2TP1
JP8JP7
CN5
P1
CN4
Figure 3-13. Part Names of G-78000a Board
CN7
JP6
JP4
JP3
P2
CN6
JP2TP1
JP8JP7
CN5
P1
CN4
CHAPTER 3 INSTALLATION
User’s Manual U14889EJ3V0UM 39
3.5 Low-Voltage Emulation Settings
Low-voltage emulation can be executed in the IE-78K0-NS-A by connecting an emulation board that supports low-
voltage operation.
(1) When using other than the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage
as that of the target to the IE-78K0-NS-A TP1 terminal pin on the G-780009 Board. (This also applies when the
voltage is 5 V.)
Figure 3-14. Position of TP1 on IE-78K0-NS-A
CN7
P2
CN6
TP1
CN5
P1
CN4
Remark The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V).
(2) When using the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage as that of
the target to the TP1 terminal pin on the IE-78018-NS-EM1. (This also applies when the voltage is 5 V.)
Figure 3-15. Position of TP1 on IE-78018-NS-EM1
CN1 CN2
TP1
Remark The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V).
Caution For details of the target voltage or maximum current consumption, refer to the relevant
emulation board user’s manual.
User’s Manual U14889EJ3V0UM
40
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC
This chapter describes the setting method when connecting the IE-78K0-NS-A.
For details, refer to the IE-70000-PCI-IF-A User’s Manual (to be prepared).
A.1 Introduction
The IE-70000-PCI-IF-A is an interface board for an IE product that is installed in the PCI bus slot of a PC.
First of all, check that you have the following items.
• Interface board (IE-70000-PCI-IF-A) for desktop PC × 1
• 8-bit connector board (connected to IE-70000-PCI-IF-A) × 1
• 32-bit connector board × 1
• User’s manual × 1
• DLL-DISK × 1
• IE-PC Driver DISK × 1
• Guarantee card × 1
<Basic specifications>
Hardware resources used
• I/O address .........0000H to FFFFH
• Interrupts.............Unused
• Memory...............Uses 80H bytes
Current consumption
300 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is
directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC
User’s Manual U14889EJ3V0UM 41
A.2 Installation
(1) Board settings
There are no jumpers or DIP switches on the IE-70000-PCI-IF-A.
(2) 8-bit connector board mounting
An 8-bit connector board is premounted at shipment.
Remark When a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector
(refer to Figure A-1) and fasten them together with screws.
Caution The 32-bit connector board is included for future function expansion.
Figure A-1. Mounting of PCI Board and Connector Boards
CH1 CH0
PCI board
32-bit connector board
Combination connector
Combination connector
Combination connector
8-bit connector board
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the PCI bus slot following the instructions in
the PC’s manual.
(4) PCI driver installation
Refer to the supplied IE-PC Driver DISK Readme_e.txt for PCI driver installation.
(5) Connecting with IE-78K0-NS-A
Using the supplied cable, connect the IE-78K0-NS-A to the CH0 side.
Caution Connection with the IE-78K0-NS-A is possible on the CH0 side only.
User’s Manual U14889EJ3V0UM
42
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)
This chapter describes the setting method when connecting the IE-78K0-NS-A.
For details, refer to the IE-70000-CD-IF-A User’s Manual (to be prepared).
B.1 Introduction
The PC card interface (IE-70000-CD-IF-A) is an interface card for an IE product that is installed in a
PCMCIA2.1/JEIDA standard Ver.4.2-compliant PC card slot.
First of all, check that you have the following items.
• PC card interface (IE-70000-CD-IF-A) × 1
• MC card cable × 1
• NS card cable × 1
• User’s manual × 1
• DLL-DISK × 1
• IE-PC Driver DISK × 1
• Guarantee card × 1
<Basic specifications>
Hardware resources used
• I/O address.........20H bytes starting from 220H, 260H, 2E0H, 320H, or 3E0H as a base address
• Interrupts.............Unused
• Memory...............Unused
Current consumption
300 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is
directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)
User’s Manual U14889EJ3V0UM 43
B.2 Installation
(1) Installation in PC
Insert the PCMCIA card in the card slot when the power supply of the PC is turned on.
For Windows NTTM4.0, insert the card in the slot when the power supply is turned off. Be careful to insert the card
in the correct direction.
(2) PCMCIA driver installation
Refer to the supplied IE-PC Driver DISK Readme_e.txt for PCMCIA driver installation.
Caution This interface card cannot be connected to the IE-78××××-R. Actually, installation ends
completely by selecting “IE-78××××-R” displayed in the IE-PC Driver DISK installation menu. In
this case, however, the installation is invalid.
(3) Connection with the IE-78K0-NS-A
Using the NS card cable, connect the IE-70000-CD-IF-A to the IE-78K0-NS-A.
Caution Be sure to use the NS-A CABLE when connecting to the IE-78K0-NS-A. If MC card cable is used,
the IE-70000-CD-IF-A may be damaged.
User’s Manual U14889EJ3V0UM
44
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
This chapter describes the setting method when connecting the IE-78K0-NS-A.
For details, refer to the IE-70000-98-IF-C User’s Manual (to be prepared).
C.1 Introduction
The IE-70000-98-IF-C is an interface board for the PC-9800 series that is installed in the C bus slot of a PC-9800
series machine.
Caution The PC98-NX series is treated as an IBM PC/AT compatible machine. Refer to APPENDIX A
INTERFACE BOARD (IE-70000-PCI-IF(-A)) FOR DESKTOP PC.
First of all, check that you have the following items.
• Interface board (IE-70000-98-IF-C) for PC-9800 series × 1
• User’s manual × 1
• DLL-DISK × 1
• IE-PC Driver DISK × 1
• Guarantee card × 1
<Basic specifications>
Applicable models
This product is designed for devices incorporating a PC-9800 series C bus.
Hardware resources used
• I/O addresses .............. 16 bytes at a 256-byte boundary (00D×H, 01D×H,...FFD×H)
• Interrupts and others.... Unused
Current consumption
500 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is
directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
User’s Manual U14889EJ3V0UM 45
C.2 Installation
(1) I/O address settings
SW1 and SW2 are the switches selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus
addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15.
In the IE-78K0-NS-A, the addresses should be set in the 16 bytes between 00D×H and FFD×H. The switch takes
the value “0” when ON and “1” when OFF.
The addresses used for setup must be values that are not used in the PC system or for other boards. In addition,
since these values are used during software installation, make a note of them for future reference.
Setting examples of I/O address, SW1 and SW2 are shown below.
Table C-1. SW1 and SW2 Settings When Setting I/O Address to 01D×H
SW1 Number 1 2 3 4 5 6 7 8
Address A4 A5 A6 A7 A8 A9 A10 A11
ON
0 0 0 0
OFF 1 1 1 1
SW2 Number 1 2 3 4 5 6 7 8
Address A12 A13 A14 A15 OFF OFF ON OFF
ON 0
0 0 0 0
OFF 1 1 1
Caution Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
User’s Manual U14889EJ3V0UM
46
(2) Jumper settings
The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers.
In the IE-78K0-NS-A, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.
Figure C-1. INT JP, WAIT JP Settings
12
WAIT JP
3
: Shorted
12
INT JP
ShortedNO USE
IR3
IR5
IR6
IR9
IR11
IR12
IR13
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the C bus slot following the instructions in
the PC’s manual.
(4) Connecting with IE-78K0-NS-A
Using the supplied cable, connect the IE-78K0-NS-A to CH0.
Caution Connection with the IE-78K0-NS-A is possible to CH0 only.
For connection with other models, refer to their respective manuals.
User’s Manual U14889EJ3V0UM 47
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES
This chapter describes the setting method when connecting the IE-78K0-NS-A.
For details, refer to the IE-70000-PC-IF-C User’s Manual (to be prepared).
D.1 Introduction
The IE-70000-PC-IF-C is an interface board for IBM PC/AT compatibles and is installed in the ISA bus slot of an
IBM PC/AT compatible.
First of all, check that you have the following items.
• Interface board (IE-70000-PC-IF-C) for IBM PC/AT × 1
• User’s manual × 1
• IE-PC Driver DISK × 1
• DLL-DISK × 1
• Guarantee card × 1
<Basic specifications>
Applicable models
The IE-70000-PC-IF-C is designed for IBM PC/AT compatibles incorporating an ISA bus.
Hardware resources
• I/O address.................. 16 bytes at any 16-byte boundary (020×H to 03F×H)
• Interrupts and others ... Unused
Current consumption
500 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is
directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES
User’s Manual U14889EJ3V0UM
48
D.2 Installation
(1) I/O address settings
SW1 and SW2 are the switches selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA bus
addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15.
In the IE-78K0-NS-A, the addresses should be set between 020×H and 03F×H. The switch takes the value “0”
when ON and “1” when OFF.
The addresses used for setup must be values that are not used in the PC system or for other boards. In addition,
since these values are used during software installation, make a note of them for future reference.
Setting examples of I/O address, SW1 and SW2 are shown below.
Table D-1. SW1 and SW2 Settings When Setting I/O Address to 020×H
SW1 Number 1 2 3 4 5 6 7 8
Address A4 A5 A6 A7 A8 A9 A10 A11
ON 0
0 0 0 0 0 0
OFF 1
SW2 Number 1 2 3 4 5 6 7 8
Address A12 A13 A14 A15 OFF OFF ON OFF
ON 0
0 0 0 0
OFF 1 1 1
Caution Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES
User’s Manual U14889EJ3V0UM 49
(2) Jumper settings
The INT JP and WAIT JP are ISA bus interrupt and WAIT selection jumpers.
In the IE-78K0-NS-A, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.
Figure D-1. INT JP, WAIT JP Settings
12
WAIT JP
3
: Shorted
12
INT JP
NO USE Shorted
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the ISA bus slot following the instructions in
the PC’s manual.
(4) Connecting with IE-78K0-NS-A
Using the supplied cable, connect the IE-78K0-NS-A to CH0.
Caution Connection with the IE-78K0-NS-A is possible to CH0 only.
For connection with other models, refer to their respective manuals.
User’s Manual U14889EJ3V0UM
50
APPENDIX E REVISION HISTORY
A history of the revisions up to this edition is shown below. “Applied to:” indicates the chapters to which the
revision was applied.
Edition Major Revisions from Previous Edition Applied to:
Change of interface board for desktop PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A Throughout
Modification of Figure 1-1 IE-78K0-NS-A System Configuration CHAPTER 1
GENERAL
A.1 Introduction
• Deletion of Applicable models
APPENDIX A
2nd
B.1 Introduction
• Deletion of Applicable models
APPENDIX B
3rd Addition of the description of the G-780009a Board Throughout
The mark shows major revised points.
