Microwave Wideband Synthesizer with Integrated VCO ADF4355 Data Sheet FEATURES GENERAL DESCRIPTION RF output frequency range: 54 MHz to 6800 MHz Fractional-N synthesizer and integer-N synthesizer High resolution 38-bit modulus Low phase noise, voltage controlled oscillator (VCO) Programmable divide by 1, 2, 4, 8, 16, 32, or 64 output Analog and digital power supplies: 3.3 V Charge pump and VCO power supplies: 5.0 V typical Logic compatibility: 1.8 V Programmable dual modulus prescaler of 4/5 or 8/9 Programmable output power level RF output mute function 3-wire serial interface Analog and digital lock detect The ADF4355 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers permits operation from 54 MHz to 6800 MHz. The ADF4355 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 54 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin and software controllable. Control of all on-chip registers is through a simple 3-wire interface. The ADF4355 operates with analog and digital power supplies ranging from 3.15 V to 3.45 V, with charge pump and VCO supplies from 4.75 V to 5.25 V. The ADF4355 also contains hardware and software power-down modes. APPLICATIONS Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT) Point to point/point to multipoint microwave links Satellites/VSATs Test equipment/instrumentation Clock generation AV DD CE REFIN A REFIN B CLK DATA LE x2 DOUBLER FUNCTIONAL BLOCK DIAGRAM 10-BIT R COUNTER DVDD RSET VP VVCO VRF AVDD MULTIPLEXER /2 DIVIDER MUXOUT LOCK DETECT CREG 1 CREG 2 DATA REGISTER FUNCTION LATCH CHARGE PUMP CPOUT PHASE COMPARATOR INTEGER REGISTER FRACTION REGISTER VTUNE VREF VBIAS VCO CORE MODULUS REGISTER VREGVCO 1/2/4/8 / 16/32/64 THIRD-ORDER FRACTIONAL INTERPOLATOR OUTPUT STAGE RFOUTA+ RFOUTA- PDBRF MULTIPLEXER AGND CPGND AGNDRF SDGND ADF4355 AGNDVCO RFOUTB+ RFOUTB- 12910-001 OUTPUT STAGE N COUNTER Figure 1. Rev. 0 Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADF4355 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Register 4 ..................................................................................... 22 Applications ....................................................................................... 1 Register 5 ..................................................................................... 23 General Description ......................................................................... 1 Register 6 ..................................................................................... 24 Functional Block Diagram .............................................................. 1 Register 7 ..................................................................................... 26 Revision History ............................................................................... 2 Register 8 ..................................................................................... 27 Specifications..................................................................................... 3 Register 9 ..................................................................................... 27 Timing Characteristics ................................................................ 5 Register 10 ................................................................................... 28 Absolute Maximum Ratings............................................................ 6 Register 11 ................................................................................... 28 Transistor Count ........................................................................... 6 Register 12 ................................................................................... 29 ESD Caution .................................................................................. 6 Register Initialization Sequence ............................................... 29 Pin Configuration and Function Descriptions ............................. 7 Frequency Update Sequence ..................................................... 29 Typical Performance Characteristics ............................................. 9 RF Synthesizer--A Worked Example ...................................... 30 Circuit Description ......................................................................... 12 Reference Doubler and Reference Divider ............................. 30 Reference Input Section ............................................................. 12 Spurious Optimization and Fast Lock ..................................... 30 RF N Divider ............................................................................... 12 Optimizing Jitter......................................................................... 30 Phase Frequency Detector (PFD) and Charge Pump ............ 13 Spur Mechanisms ....................................................................... 31 MUXOUT and Lock Detect ...................................................... 13 Lock Time.................................................................................... 31 Input Shift Registers ................................................................... 13 Applications Information .............................................................. 32 Program Modes .......................................................................... 13 Direct Conversion Modulator .................................................. 32 VCO.............................................................................................. 14 Power Supplies ............................................................................ 33 Output Stage ................................................................................ 14 Register Maps .................................................................................. 16 Printed Circuit Board (PCB) Design Guidelines for a ChipScale Package .............................................................................. 33 Register 0 ..................................................................................... 18 Output Matching ........................................................................ 34 Register 1 ..................................................................................... 19 Outline Dimensions ....................................................................... 35 Register 2 ..................................................................................... 20 Ordering Guide .......................................................................... 35 Register 3 ..................................................................................... 21 REVISION HISTORY 4/15--Revision 0: Initial Version Rev. 0 | Page 2 of 35 Data Sheet ADF4355 SPECIFICATIONS AVDD = DVDD = VRF = 3.3 V 5%, 4.75 V VP = VVCO 5.25 V, AGND = CPGND = AGNDVCO = SDGND = AGNDRF = 0 V, RSET = 5.1 k, dBm referred to 50 , TA = TMIN to TMAX, unless otherwise noted. Table 1. Parameter REFINA/REFINB CHARACTERISTICS Input Frequency Single-Ended Mode Differential Mode Input Sensitivity Single-Ended Mode Symbol Min Typ Max Unit 10 10 250 600 MHz MHz 0.4 AVDD V p-p 0.4 1.8 V p-p 60 250 125 pF pF A A MHz For f < 10 MHz, ensure slew rate > 21 V/s Differential Mode Input Capacitance Single-Ended Mode Differential Mode Input Current Phase Detector Frequency CHARGE PUMP (CP) Charge Pump Current, Sink/Source High Value Low Value RSET Range Current Matching ICP vs. VCP 1 ICP vs. Temperature LOGIC INPUTS Input High Voltage Input Low Voltage Input Current Input Capacitance LOGIC OUTPUTS Output High Voltage Output High Current Output Low Voltage POWER SUPPLIES Analog Power Digital Power and RF Supply Voltage Charge Pump and VCO Voltage Charge Pump Supply Power Current Digital Power Supply Current + Analog Power Supply Curent 3 Output Dividers Supply Current RFOUTA/RFOUTB Supply Current Low Power Sleep Mode Test Conditions/Comments 6.9 1.4 ICP VINH VINL IINH/IINL CIN 1.5 VOH DVDD - 0.4 1.5 mA mA k % % % 0.6 1 3.0 3.15 4.75 AVDD 5.0 8 62 6 to 36 70 16/20/ 42/55 500 1000 500 0.4 3.45 V 5.25 9 69 V Rev. 0 | Page 3 of 35 85 20/35/ 50/70 Fixed 0.5 V VCP1 VP - 0.5 V 0.5 V VCP1 VP - 0.5 V VCP1 = 2.5 V V V A pF V V A V 1.8 IOH VOL IVCO IRFOUT x Single-ended reference programmed Differential reference programmed RSET = 5.1 k 4.8 0.3 5.1 3 3 1.5 AVDD DVDD, VRF VP, VVCO IP DIDD, AIDD REFINA biased at AVDD/2; ac coupling ensures AVDD/2 bias LVDS and LVPECL compatible, REFINA/REFINB biased at 2.1 V; ac coupling ensures 2.1 V bias 1.8 V output selected IOL 2 = 500 A Voltages must equal AVDD VP must equal VVCO mA mA mA mA A A Each output divide by 2 consumes 6 mA RF output stage is programmable; RFOUTB+/RFOUTB- powered off Hardware power-down Software power-down ADF4355 Parameter RF OUTPUT CHARACTERISTICS VCO Frequency Range RF Output Frequency VCO Sensitivity Frequency Pushing (Open-Loop) Frequency Pulling (Open-Loop) Harmonic Content Second Third RF Output Power 4 RF Output Power Variation RF Output Power Variation (over Frequency) Level of Signal with RF Output Disabled Data Sheet Symbol Min Typ Max Unit Test Conditions/Comments 6800 6800 Fundamental VCO range 15 15 0.5 MHz MHz MHz/V MHz/V MHz -27 -22 -20 -12 +8 +3 1 3 dBc dBc dBc dBc dBm dBm dB dB Fundamental VCO output (RFOUTA+) Divided VCO output (RFOUTA+) Fundamental VCO output (RFOUTA+) Divided VCO output (RFOUTA+) RFOUTA+ = 1 GHz RFOUTA+/RFOUTA- = 4.4 GHz RFOUTA+/RFOUTA- = 4.4 GHz RFOUTA+/RFOUTA- = 1 GHz to 4.4 GHz -60 dBm RFOUTA+/RFOUTA- = 1 GHz, VCO = 4 GHz -30 dBm RFOUTA+/RFOUTA- = 4.4 GHz, VCO = 4.4 GHz 3400 53.125 KV NOISE CHARACTERISTICS Fundamental VCO Phase Noise Performance Normalized In-Band Phase Noise Floor Fractional Channel 5 Integer Channel 6 Normalized 1/f Noise, PN1_f 7 Integrated RMS Jitter Spurious Signals due to Phase Frequency Detector (PFD) Frequency Voltage standing wave ratio (VSWR) = 2:1 VCO noise in open-loop conditions -116 -136 -138 -155 -113 -133 -135 -153 -110 -130 -132 -150 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz 100 kHz offset from 3.4 GHz carrier 800 kHz offset from 3.4 GHz carrier 1 MHz offset from 3.4 GHz carrier 10 MHz offset from 3.4 GHz carrier 100 kHz offset from 5.0 GHz carrier 800 kHz offset from 5.0 GHz carrier 1 MHz offset from 5.0 GHz carrier 10 MHz offset from 5.0 GHz carrier 100 kHz offset from 6.8 GHz carrier 800 kHz offset from 6.8 GHz carrier 1 MHz offset from 6.8 GHz carrier 10 MHz offset from 6.8 GHz carrier -221 -223 -116 150 -80 dBc/Hz dBc/Hz dBc/Hz fs dBc 10 kHz offset; normalized to 1 GHz VCP is the voltage at the CPOUT pin. IOL is the output low current. 3 TA = 25C; AVDD = DVDD = VRF = 3.3 V; VVCO = VP = 5.0 V; prescaler = 4/5; fREFIN = 122.88 MHz; fPFD = 61.44 MHz; and fRF = 1650 MHz. 4 RF output power using the EV-ADF4355SD1Z evaluation board measured into a spectrum analyzer, with board and cable losses de-embedded. The EV-ADF4355SD1Z RF outputs are pulled up externally using a 4.7 nH inductor. Unused RF output pins are terminated in 50 . 5 Use this figure to calculate the phase noise for any application. To calculate in-band phase noise performance as seen at the VCO output, use the following formula: -221 + 10log(fPFD) + 20logN. The value given is the lowest noise mode for the fractional channel. 6 Use this figure to calculate the phase noise for any application. To calculate in-band phase noise performance as seen at the VCO output, use the following formula: -223 + 10log(fPFD) + 20logN. The value given is the lowest noise mode for the integer channel. 7 The PLL phase noise is composed of 1/f (flicker) noise plus the normalized PLL noise floor. The formula for calculating the 1/f noise contribution at an RF frequency (fRF) and at a frequency offset (f) is given by PN = P1_f + 10log(10 kHz/f) + 20log(fRF/1 GHz). Both the normalized phase noise floor and flicker noise are modeled in the ADIsimPLL design tool. 1 2 Rev. 0 | Page 4 of 35 Data Sheet ADF4355 TIMING CHARACTERISTICS AVDD = DVDD =VRF = 3.3 V 5%, 4.75 V VP = VVCO 5.25 V, AGND = CPGND = AGNDVCO = SDGND = AGNDRF = 0 V, RSET = 5.1 k, dBm referred to 50 , TA = TMIN to TMAX, unless otherwise noted. Table 2. Write Timing Parameter t1 t2 t3 t4 t5 t6 t7 Limit 20 10 10 25 25 10 20 Unit ns min ns min ns min ns min ns min ns min ns min Description LE setup time DATA to CLK setup time DATA to CLK hold time CLK high duration CLK low duration CLK to LE setup time LE pulse width Write Timing Diagram t4 t5 CLK t3 t2 DATA DB31 (MSB) DB30 DB3 (CONTROL BIT C4) DB2 (CONTROL BIT C3) DB1 (CONTROL BIT C2) DB0 (LSB) (CONTROL BIT C1) t7 t1 t6 Figure 2. Write Timing Diagram Rev. 0 | Page 5 of 35 12910-002 LE ADF4355 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 3. Parameter VRF, DVDD, AVDD to GND1 AVDD to DVDD VP, VVCO to GND1 VP, VVCO to AVDD CPOUT to GND1 Digital Input/Output Voltage to GND1 Analog Input/Output Voltage to GND1 REFINA, REFINB to GND1 REFINA to REFINB Operating Temperature Range Storage Temperature Range Maximum Junction Temperature JA, Thermal Impedance Pad Soldered to GND1 Reflow Soldering Peak Temperature Time at Peak Temperature Electrostatic Discharge (ESD) Charged Device Model Human Body Model 1 Rating -0.3 V to +3.6 V -0.3 V to +0.3 V -0.3 V to +5.8 V -0.3 V to AVDD + 2.5 V -0.3 V to VP + 0.3 V -0.3 V to DVDD + 0.3 V -0.3 V to AVDD + 0.3 V -0.3 V to AVDD + 0.3 V 2.1 V -40C to +85C -65C to +125C 150C 27.3C/W Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. The ADF4355 is a high performance RF integrated circuit with an ESD rating of 2500 V and is ESD sensitive. Take proper precautions for handling and assembly. TRANSISTOR COUNT The transistor count for the ADF4355 is 103,665 (CMOS) and 3214 (bipolar). ESD CAUTION 260C 40 sec 1000 V 2500 V GND = AGND = SDGND = AGNDRF = AGNDVCO = CPGND = 0 V. Rev. 0 | Page 6 of 35 Data Sheet ADF4355 32 31 30 29 28 27 26 25 CREG 2 SDGND MUXOUT REFINA REFINB DVDD PDBRF CREG 1 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 ADF4355 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 VBIAS VREF RSET AGNDVCO VTUNE VREGVCO AGNDVCO VVCO NOTES 1. THE EXPOSED PAD MUST BE CONNECTED TO AGND. 12910-003 AGND VRF RFOUTA+ RFOUTA- AGNDRF RFOUTB+ RFOUTB- AV DD 9 10 11 12 13 14 15 16 CLK DATA LE CE AVDD VP CPOUT CPGND Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic CLK 2 DATA 3 LE 4 CE 5, 16 AVDD 6 VP 7 CPOUT 8 9 10 CPGND AGND VRF 11 RFOUTA+ 12 RFOUTA- 13 14 AGNDRF RFOUTB+ 15 RFOUTB- 17 VVCO 18, 21 19 AGNDVCO VREGVCO 20 VTUNE Description Serial Clock Input. Data is clocked into the 32-bit shift register on the CLK rising edge. This input is a high impedance CMOS input. Serial Data Input. The serial data is loaded most significant bit (MSB) first with the four least significant bits (LSBs) as the control bits. This input is a high impedance CMOS input. Load Enable, CMOS Input. When LE goes high, the data stored in the shift register is loaded into the register that is selected by the four LSBs. Chip Enable. A logic low on this pin powers down the device and puts the charge pump into three-state mode. A logic high (at levels equal to DVDD) on this pin powers up the device, depending on the status of the power-down bits. Analog Power Supply. This pin ranges from 3.15 V to 3.45 V. Connect decoupling capacitors to the analog ground plane as close to this pin as possible. AVDD must have the same value as DVDD. Charge Pump Power Supply. VP must have the same value as VVCO. Connect decoupling capacitors to the ground plane as close to this pin as possible. Charge Pump Output. When enabled, this output provides ICP to the external loop filter. The output of the loop filter is connected to VTUNE to drive the internal VCO. Charge Pump Ground. This output is the ground return pin for CPOUT. Analog Ground. Ground return pin for AVDD. Power Supply for the RF Output. Connect decoupling capacitors to the analog ground plane as close to this pin as possible. VRF must have the same value as AVDD. VCO Output. The output level is programmable. The VCO fundamental output or a divided down version is available. Complementary VCO Output. The output level is programmable. The VCO fundamental output or a divided down version is available. RF Output Stage Ground. Ground return pins for the RF output stage. Auxiliary VCO Output. The output level is programmable. The VCO fundamental output or a divided down version is available. Complementary Auxiliary VCO Output. The output level is programmable. The VCO fundamental output or a divided down version is available. Power Supply for the VCO. The voltage on this pin ranges from 4.75 V to 5.25 V. Connect decoupling capacitors to the analog ground plane as close to this pin as possible. VCO Ground. Ground return path for the VCO. VCO Compensation Node. Connect decoupling capacitors to the ground plane as close to this pin as possible. Connect this pin directly to VVCO. Control Input to the VCO. This voltage determines the output frequency and is derived from filtering the CPOUT output voltage. Rev. 0 | Page 7 of 35 ADF4355 Pin No. 22 23 Mnemonic RSET VREF 24 25, 32 VBIAS CREG1, CREG2 26 27 PDBRF DVDD 28 29 30 REFINB REFINA MUXOUT 31 SDGND EP Data Sheet Description Bias Current Resistor. Connecting a resistor between this pin and ground sets the charge pump output current. Internal Compensation Node. DC biased at half the tuning range. Connect decoupling capacitors to the ground plane as close to this pin as possible. Reference Voltage. Connect a 100 nF decoupling capacitor to the ground plane as close to this pin as possible. Outputs from the LDO Regulator. Pin 25 and Pin 32 are the supply voltages to the digital circuits and have a nominal voltage of 1.8 V. Decoupling capacitors of 100 nF connected to AGND are required for these pins. RF Power-Down. A logic low on this pin mutes the RF outputs. This mute function is also software controllable. Digital Power Supply. This pin must be at the same voltage as AVDD. Place decoupling capacitors to the ground plane as close to this pin as possible. Complementary Reference Input. If unused, ac-couple this pin to AGND. Reference Input. Multiplexer Output. The multiplexer output allows the digital lock detect, the analog lock detect, scaled RF, or the scaled reference frequency to be externally accessible. Digital - Modulator Ground. Pin 31 is the ground return path for the - modulator. Exposed Pad. The exposed pad must be connected to AGND. Rev. 0 | Page 8 of 35 Data Sheet ADF4355 -50 -50 -70 -70 PHASE NOISE (dBc/Hz) -90 -110 -130 -150 10k 100k 1M 10M 100M Figure 4. Open-Loop VCO Phase Noise, 3.4 GHz -130 -170 1k -50 -70 -70 -90 -110 -130 -150 1M 10M 100M /1 /2 /4 /8 /16 /32 /64 -90 -110 -130 10k 100k 1M 10M 100M -170 12910-005 1k Figure 5. Open-Loop VCO Phase Noise, 5.0 GHz 1k 10k 100k 1M 10M 100M FREQUENCY (Hz) 12910-008 -150 FREQUENCY (Hz) Figure 8. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Dividers, VCO = 5.0 GHz, PFD = 61.44 MHz, Loop Bandwidth = 20 kHz -50 -70 -70 PHASE NOISE (dBc/Hz) -50 -90 -110 -130 -150 /1 /2 /4 /8 /16 /32 /64 -90 -110 -130 -150 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 6. Open-Loop VCO Phase Noise, 6.8 GHz 100M -170 12910-006 -170 100k Figure 7. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Dividers, VCO = 3.4 GHz, PFD = 61.44 MHz, Loop Bandwidth = 20 kHz -50 -170 10k FREQUENCY (Hz) PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) -110 12910-007 1k FREQUENCY (Hz) PHASE NOISE (dBc/Hz) -90 -150 12910-004 -170 /1 /2 /4 /8 /16 /32 /64 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M 12910-009 PHASE NOISE (dBc/Hz) TYPICAL PERFORMANCE CHARACTERISTICS Figure 9. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Dividers, VCO = 6.8 GHz, PFD = 61.44 MHz, Loop Bandwidth = 20 kHz Rev. 0 | Page 9 of 35 ADF4355 /1 /2 OUTPUT POWER (dBm) PHASE NOISE (dBc/Hz) -70 -90 -110 -130 -170 1k 10k 100k 1M 10M 100M FREQUENCY (Hz) 12910-010 -150 Figure 10. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Divide by 2, VCO = 3.4 GHz, PFD = 61.44 MHz, Loop Bandwidth = 2 kHz -50 10 9 8 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 1 2 3 4 5 6 7 FREQUENCY (GHz) Figure 13. Output Power vs. Frequency, RFOUTA+/RFOUTA- (7.5 nH Inductors, 10 pF Bypass Capacitors, Board Losses De-Embedded) 0 /1 /2 SECOND HARMONIC THIRD HARMONIC -5 -70 -10 -15 -90 POWER (dBc) PHASE NOISE (dBc/Hz) -40C +25C +85C 12910-016 -50 Data Sheet -110 -130 -20 -25 -30 -35 -40 -150 1k 10k 100k 1M 10M 100M FREQUENCY (Hz) Figure 11. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Divide by 2, VCO = 5.0 GHz, PFD = 61.44 MHz, Loop Bandwidth = 2 kHz -50 -50 12910-011 -170 2 3 4 5 6 7 FREQUENCY (GHz) Figure 14. RFOUTA+/RFOUTA- Harmonics vs. Frequency (7.5 nH Inductors, 10 pF Bypass Capacitors, Board Losses De-Embedded) 10 /1 /2 8 -70 6 4 -90 POWER (dBm) PHASE NOISE (dBc/Hz) 1 12910-017 -45 -110 -130 2 0 -2 -4 -6 -150 10k 100k 1M FREQUENCY (Hz) 10M 100M 12910-012 1k -10 Figure 12. Closed-Loop Phase Noise, RFOUTA+, Fundamental VCO and Divide by 2, VCO = 6.8 GHz, PFD = 61.44 MHz, Loop Bandwidth = 2 kHz 0 1 2 3 4 FREQUENCY (GHz) 5 6 7 12910-018 -8 -170 Figure 15. RFOUTA+/RFOUTA- Power vs. Frequency (100 nH Inductors, 100 pF Bypass Capacitors, Board Measurement) Rev. 0 | Page 10 of 35 Data Sheet 0.40 -100 -110 0.30 0.25 -120 0.20 -130 0.15 -140 0.10 -150 0.05 1.8 2.8 3.8 4.8 5.8 6.8 OUTPUT FREQUENCY (GHz) Figure 16. RMS Jitter vs. Output Frequency, PFD Frequency = 61.44 MHz, Loop Filter = 20 kHz -50 10k 100k 1M 10M 100M FREQUENCY (Hz) Figure 19. Fractional-N Spur Performance, W-CDMA Band, RFOUTA+ = 2113.5 MHz, REFIN = 122.88 MHz, PFD = 61.44 MHz, Output Divide by 2 Selected, Loop Filter Bandwidth = 20 kHz, Channel Spacing = 20 kHz NOISE AND SPUR POWER (dBc/Hz) -90 -100 -70 -110 -80 -120 -130 -90 -140 -100 0 2 1 3 4 5 6 RFOUTA+/RFOUTA- OUTPUT FREQUENCY (GHz) 7 -160 10k 100k 1M 10M 100M FREQUENCY (Hz) Figure 17. PFD Spur Amplitude vs. RFOUTA+/RFOUTA- Output Frequency, PFD = 15.36 MHz, PFD = 30.72 MHz, PFD = 61.44 MHz, Loop Filter = 20 kHz Figure 20. Fractional-N Spur Performance, RFOUTA+ = 2.591 GHz, REFIN = 122.88 MHz, PFD = 61.44 MHz, Output Divide-by-2 Selected, Loop Filter Bandwidth = 20 kHz, Channel Spacing = 20 kHz -80 4.65 4.60 -90 4.55 FREQUENCY (GHz) -100 -110 -120 -130 -140 4.50 4.45 1 4.40 4.35 4.30 4.25 -150 4.20 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M 4.15 -1 12910-024 -160 1k 12910-026 -150 12910-022 -110 NOISE AND SPUR POWER (dBc/Hz) 1k -80 PFD = 15.36MHz PFD = 30.72MHz PFD = 61.44MHz -60 -160 12910-021 0 0.8 Figure 18. Fractional-N Spur Performance, GSM1800 Band, RFOUTA+ = 1550.2 MHz, REFIN = 122.88 MHz, PFD = 61.44 MHz, Output Divide by 4 Selected, Loop Filter Bandwidth = 20 kHz, Channel Spacing = 20 kHz 0 1 TIME (ms) 2 3 4 12910-128 RMS JITTER (ps) 0.35 PFD SPUR AMPLITUDE (dBc) -90 12910-025 0.45 -80 RMS JITTER (ps) 1kHz TO 20MHz RMS JITTER (ps) 12kHz TO 20MHz NOISE AND SPUR POWER (dBc/Hz) 0.50 ADF4355 Figure 21. Lock Time for 250 MHz Jump from 4150 MHz to 4400 MHz, Loop Bandwidth = 20 kHz Rev. 0 | Page 11 of 35 ADF4355 Data Sheet CIRCUIT DESCRIPTION REFERENCE INPUT SECTION INT, FRACx, MODx, and R Counter Relationship Figure 22 shows the reference input stage. The reference input can accept both single-ended and differential signals. Use the reference mode bit (Register 4, DB9) to select the signal. To use a differential signal on the reference input, program this bit high. In this case, SW1 and SW2 are open, SW3 and SW4 are closed, and the current source that drives the differential pair of transistors switches on. The differential signal buffers and provides an emitter-coupled logic (ECL) to CMOS converter. When a single-ended signal is used as the reference, program Bit DB9 in Register 4 to 0. Connect the single-ended reference signal to REFINA. In this case, SW1 and SW2 are closed, SW3 and SW4 are open, and the current source that drives the differential pair of transistors switches off. The INT, FRAC1, FRAC2, MOD1, and MOD2 values, in conjunction with the R counter, make it possible to generate output frequencies that are spaced by fractions of the PFD frequency (fPFD). For more information, see the RF Synthesizer-- A Worked Example section. When the input reference frequency is below 250 MHz, it is recommended to operate in single-ended mode for best spur performance. REFERENCE INPUT MODE 85k SW2 BUFFER SW1 SW3 MULTIPLEXER TO R COUNTER AVDD ECL TO CMOS CONVERTER REFINA REFINB 2.5k 2.5k 12910-226 SW4 BIAS GENERATOR Figure 22. Reference Input Stage RF N DIVIDER The RF N divider allows a division ratio in the PLL feedback path. Determine the division ratio by the INT, FRAC1, FRAC2, and MOD2 values that this divider comprises. RF N COUNTER FRAC1 + N = INT + MOD2 MOD1 TO PFD N COUNTER THIRD-ORDER FRACTIONAL INTERPOLATOR INT REGISTER FRAC1 REGISTER FRAC2 VALUE MOD2 VALUE 12910-027 FROM VCO OUTPUT/ OUTPUT DIVIDERS FRAC2 Calculate the RF VCO frequency (VCOOUT) by (1) VCOOUT = fPFD x N where: VCOOUT is the output frequency of the VCO (without using the output divider). fPFD is the frequency of the phase frequency detector. N is the desired value of the feedback counter, N. Calculate fPFD by (2) fPFD = REFIN x [(1 + D)/(R x (1 + T))] where: REFIN is the reference input frequency. D is the REFIN doubler bit. R is the preset divide ratio of the binary 10-bit programmable reference counter (1 to 1023). T is the REFIN divide by 2 bit (0 or 1). N comprises FRAC2 FRAC1 MOD2 N INT (3) MOD1 where: INT is the 16-bit integer value (23 to 32,767 for the 4/5 prescaler, 75 to 65,535 for the 8/9 prescaler). FRAC1 is the numerator of the primary modulus (0 to 16,777,215). FRAC2 is the numerator of the 14-bit auxiliary modulus (0 to 16,383). MOD2 is the programmable, 14-bit auxiliary fractional modulus (2 to 16,383). MOD1 is a 24-bit primary modulus with a fixed value of 224 = 16,777,216. Equation 3 results in a very fine frequency resolution with no residual frequency error. To apply this formula, take the following steps: 1. Calculate N by dividing VCOOUT/fPFD. 2. The integer value of this number forms INT. 3. Subtract the INT value from the full N value. 4. Multiply the remainder by 224. 5. The integer value of this number forms FRAC1. 6. Calculate MOD2 based on the channel spacing (fCHSP) by (4) MOD2 = fPFD/GCD(fPFD, fCHSP) where: GCD(fPFD, fCHSP) is the greatest common divider of the PFD frequency and the channel spacing frequency. fCHSP is the desired channel spacing frequency. 7. Figure 23. RF N Divider Rev. 0 | Page 12 of 35 Calculate FRAC2 by the following equation: FRAC2 = [(N - INT) x 224 - FRAC1)] x MOD2 (5) Data Sheet ADF4355 DVDD The FRAC2 and MOD2 fraction results in outputs with zero frequency error for channel spacings when fPFD/GCD(fPFD/fCHSP) < 16,383 THREE-STATE OUTPUT (6) where: fPFD is the frequency of the phase frequency detector. GCD is a greatest common denominator function. fCHSP is the desired channel spacing frequency. DVDD SDGND R DIVIDER OUTPUT N DIVIDER OUTPUT MUX CONTROL ANALOG LOCK DETECT If zero frequency error is not required, the MOD1 and MOD2 denominators operate together to create a 38-bit resolution modulus. DIGITAL LOCK DETECT SDGND Figure 25. MUXOUT Block Diagram When FRAC1 and FRAC2 = 0, the synthesizer operates in integer-N mode. INPUT SHIFT REGISTERS R Counter The 10-bit R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 1023 are allowed. PHASE FREQUENCY DETECTOR (PFD) AND CHARGE PUMP The PFD takes inputs from the R counter and N counter and produces an output proportional to the phase and frequency difference between them. Figure 24 is a simplified schematic of the PFD. The PFD includes a fixed delay element that sets the width of the antibacklash pulse. This pulse ensures that there is no dead zone in the PFD transfer function and provides a consistent reference spur level. Set the phase detector polarity to positive on this device because of the positive tuning of the VCO. D1 Q1 UP U1 CLR1 DELAY HIGH U3 CHARGE PUMP CP CLR2 DOWN D2 Q2 U2 -IN 12910-028 +IN 12910-029 RESERVED INT N Mode HIGH MUXOUT Figure 24. PFD Simplified Schematic The ADF4355 digital section includes a 10-bit R counter, a 16-bit RF integer-N counter, a 24-bit FRAC1 counter, a 14-bit auxiliary fractional counter, and a 14-bit auxiliary modulus counter. Data clocks into the 32-bit shift register on each rising edge of CLK. The data clocks in MSB first. Data transfers from the shift register to one of 12 latches on the rising edge of LE. The state of the four control bits (C4, C3, C2, and C1) in the shift register determines the destination latch. As shown in Figure 2, the four least significant bits (LSBs) are DB3, DB2, DB1, and DB0. The truth table for these bits is shown in Table 5. Figure 28 and Figure 29 summarize the programing of the latches. Table 5. Truth Table for the C4, C3, C2, and C1 Control Bits C4 0 0 0 0 0 0 0 0 1 1 1 1 1 C3 0 0 0 0 1 1 1 1 0 0 0 0 1 Control Bits C2 0 0 1 1 0 0 1 1 0 0 1 1 0 C1 0 1 0 1 0 1 0 1 0 1 0 1 0 Register Register 0 Register 1 Register 2 Register 3 Register 4 Register 5 Register 6 Register 7 Register 8 Register 9 Register 10 Register 11 Register 12 PROGRAM MODES MUXOUT AND LOCK DETECT The output multiplexer on the ADF4355 allows the user to access various internal points on the chip. The M3, M2, and M1 bits in Register 4 control the state of MUXOUT. Figure 25 shows the MUXOUT section in block diagram form. Table 5 and Figure 28 through Figure 42 show the program modes that must be set up in the ADF4355. The following settings in the ADF4355 are double buffered: main fractional value (FRAC1), auxiliary modulus value (MOD2), auxiliary fractional value (FRAC2), reference doubler, reference divide by 2 (RDIV2), R counter value, and charge pump current setting. Two events must occur before the ADF4355 uses a new value for any of the double buffered settings. First, the new value must latch into the device by writing to the appropriate register, and second, a new write to Register 0 must be performed. Rev. 0 | Page 13 of 35 ADF4355 Data Sheet VCO The VCO core in the ADF4355 consists of four separate VCOs, each of which uses 256 overlapping bands, which allows covering a wide frequency range without a large VCO sensitivity (KV) and without resultant poor phase noise and spurious performance. The correct VCO and band are chosen automatically by the VCO and band select logic when Register 0 is updated and autocalibration is enabled. The VCO VTUNE is disconnected from the output of the loop filter and is connected to an internal reference voltage. The R counter output is used as the clock for the band select logic. After band selection, normal PLL action resumes. The nominal value of KV is 15 MHz/V when the N divider is driven from the VCO output, or the KV value is divided by D. D is the output divider value if the N divider is driven from the RF output divider (chosen by programming Bits[D23:D21] in Register 6). The VCO shows variation of KV as the tuning voltage, VTUNE, varies within the band and from band to band. For wideband applications covering a wide frequency range (and changing output dividers), a value of 15 MHz/V provides the most accurate KV, because this value is closest to the average value. Figure 26 shows how KV varies with fundamental VCO frequency along with an average value for the frequency band. Users may prefer this figure when using narrow-band designs. 50 The RFOUTA+ and RFOUTA- pins of the ADF4355 connect to the collectors of an NPN differential pair driven by buffered outputs of the VCO, as shown in Figure 27. In this scheme, the ADF4355 contains internal 50 resistors connected to the VRF pin. To optimize the power dissipation vs. the output power requirements, the tail current of the differential pair is programmable using Bits[D2:D1] in Register 6. Four current levels can be set. These levels give approximate output power levels of -4 dBm, -1 dBm, +2 dBm, and +5 dBm, respectively, using a 50 resistor to VRF and ac coupling into a 50 load. For accurate power levels, refer to the Typical Performance Characteristics section. With an output power of 5 dBm, an external shunt inductor is necessary to provide higher power levels; however, this addition results in less wideband than the internal bias only. Terminate the unused complementary output with a similar circuit to the used output. VRF 50 RFOUTA+ VCO 50 RFOUTA- BUFFER/ DIVIDE BY 1/2/4/8/ 16/32/64 Figure 27. Output Stage Another feature of the ADF4355 is that the supply current to the output stages can shut down until the ADF4355 achieves lock as measured by the digital lock detect circuitry. The mute till lock detect (MTLD) bit (DB11) in Register 6 enables this. 40 35 30 LINEAR TREND LINE AVERAGE VCO SENSITIVITY 25 20 15 10 3.8 4.3 4.8 5.3 5.8 FREQUENCY (GHz) 6.3 6.8 12910-133 5 0 3.3 VRF The RFOUTB+/RFOUTB- pins are duplicate outputs that can be used independently or in addition to the RFOUTA+/RFOUTA- pins. 45 VCO SENSITIVITY, KV (MHz/V) OUTPUT STAGE 12910-032 For example, to ensure that the modulus value loads correctly, every time the modulus value updates, Register 0 must be written to. The RF divider select in Register 6 is also double buffered, but only when DB14 of Register 4 is high. Figure 26. KV vs. Frequency Rev. 0 | Page 14 of 35 Data Sheet ADF4355 Table 6. Total IDD (RFOUTA Refers to RFOUTA+/RFOUTA-) Divide By 5 V Supply (IVCO and IP) 3.3 V Supply (AIDD, DIDD, IRF) 1 2 4 8 16 32 64 RFOUTA Off 78 mA RFOUTA = -4 dBm 78 mA RFOUTA = -1 dBm 78 mA RFOUTA = +2 dBm 78 mA RFOUTA = +5 dBm 78 mA 79.8 mA 87.8 mA 97.1 mA 104.9 mA 109.8 mA 113.6 mA 115.9 mA 101.3 mA 110.1 mA 119.3 mA 127.1 mA 131.8 mA 135.5 mA 137.8 mA 111.9 mA 120.6 mA 130.1 mA 137.8 mA 142.7 mA 146.5 mA 148.9 mA 122.7 mA 131.9 mA 141.6 mA 149.2 mA 154.1 mA 157.8 mA 160.1 mA 132.8 mA 141.9 mA 152.1 mA 159.7 mA 164.6 mA 168.4 mA 170.8 mA Rev. 0 | Page 15 of 35 ADF4355 Data Sheet REGISTER MAPS AUTOCAL PRESCALER REGISTER 0 RESERVED CONTROL BITS 16-BIT INTEGER VALUE (INT) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 0 0 0 0 0 0 0 0 0 0 PR1 AC1 N15 N16 N14 N13 N12 N11 N10 N9 N8 N7 DB8 DB7 DB6 DB5 DB4 N5 N4 N3 N2 N1 N6 DB3 DB2 C4(0) C3(0) DB1 DB0 C2(0) C1(0) REGISTER 1 RESERVED CONTROL BITS DBR 1 24-BIT MAIN FRACTIONAL VALUE (FRAC1) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 F24 0 F23 F22 F21 F20 F19 F18 F17 F16 F15 F14 F13 F12 F11 F10 F9 F8 F7 F6 DB7 DB6 F5 F4 F3 DB5 DB4 DB3 F2 C4(0) C3(0) C2(0) C1(1) F1 DB2 DB1 DB0 REGISTER 2 14-BIT AUXILIARY FRACTIONAL VALUE (FRAC2) DBR 1 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 F14 F13 F11 F12 F10 F9 F8 F7 F6 F5 CONTROL BITS 14-BIT AUXILIARY MODULUS VALUE (MOD2) DBR 1 F4 F3 F2 M14 F1 M13 M12 M11 M10 M9 M8 M7 DB8 DB7 DB6 DB5 DB4 M5 M4 M3 M2 M1 M6 DB3 DB2 DB1 DB0 C4(0) C3(0) C2(1) C1(0) PHASE ADJUST PHASE RESYNC SD LOAD RESET RESERVED REGISTER 3 CONTROL BITS DBR 1 24-BIT PHASE VALUE (PHASE) P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 DB5 DB4 DB3 P6 P5 P4 P3 P2 P1 C4(0) C3(0) C2(1) C1(1) COUNTER RESET P24 CP THREESTATE PA1 POWER-DOWN PR1 PD POLARIT Y SD1 MUX LOGIC 0 REF MODE DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB2 DB1 DB0 CONTROL BITS DBR 1 DOUBLE BUFF MUXOUT RDIV2 RESERVED REFERENCE DOUBLER DBR 1 REGISTER 4 DBR 1 10-BIT R COUNTER CURRENT SETTING DBR 1 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 M3 M2 M1 RD2 RD1 R10 R9 R8 R7 R6 R5 R4 R3 R2 D1 R1 CP4 CP3 CP2 CP1 U6 DB7 DB6 U5 U4 U3 DB5 DB4 DB3 U2 C4(0) C3(1) C2(0) C1(0) U1 DB2 DB1 DB0 REGISTER 5 CONTROL BITS DB31 DB30 DB29 DB28 DB27 DB26 0 0 0 0 0 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 0 1 0 RF OUTPUT ENABLE RESERVED RF OUTPUT POWER 0 DB3 DB2 DB1 DB0 C4(0) C3(1) C2(0) C1(1) AUX RF OUTPUT POWER CONTROL BITS DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 1DBR 2DBB BL10 BL9 1 0 1 0 D13 D12 D11 D10 BL8 BL7 BL6 BL5 BL4 BL3 BL2 BL1 1 D8 = DOUBLE BUFFERED REGISTER--BUFFERED BY THE WRITE TO REGISTER 0. = DOUBLE BUFFERED BITS--BUFFERED BY A WRITE TO REGISTER 0 WHEN BIT DB14 OF REGISTER 4 IS HIGH. Figure 28. Register Summary (Register 0 to Register 6) Rev. 0 | Page 16 of 35 1 D6 D5 D4 D3 D2 D1 DB2 DB1 DB0 C4(0) C3(1) C2(1) C1(0) 12910-034 AUX RF OUTPUT ENABLE CHARGE PUMP BLEED CURRENT RESERVED RF DIVIDER SELECT2 MTLD RESERVED RESERVED FEEDBACK SELECT NEGATIVE BLEED RESERVED GATED BLEED REGISTER 6 Data Sheet ADF4355 LDO MODE LD CYCLE COUNT RESERVED FRAC-N LD PRECISION RESERVED LOL MODE LE SYNC REGISTER 7 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 1 0 0 LE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 LD4 LD5 LOL LD3 CONTROL BITS DB3 DB2 DB1 DB0 LD2 LD1 C4(0) C3(1) C2(1) C1(1) REGISTER 8 CONTROL BITS RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 1 0 0 0 0 0 0 1 0 1 1 0 1 0 0 0 0 0 1 0 DB7 DB6 0 0 DB5 DB4 1 0 0 DB3 DB2 DB1 DB0 C4(1) C3(0) C2(0) C1(0) REGISTER 9 VCO BAND DIVISION SYNTHESIZER LOCK TIMEOUT AUTOMATIC LEVEL TIMEOUT TIMEOUT DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 VC8 VC7 VC6 VC5 VC4 VC3 VC2 VC1 TL10 TL9 TL8 TL7 TL6 TL5 TL4 TL3 TL2 TL1 AL5 AL4 AL3 AL2 AL1 SL5 CONTROL BITS DB7 DB6 DB5 DB4 SL4 SL2 SL3 DB3 DB2 DB1 DB0 SL1 C4(1) C3(0) C2(0) C1(1) ADC CLOCK DIVIDER RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 AD8 AD7 AD6 AD5 AD4 DB7 DB6 AD3 AD2 AD1 ADC ENABLE ADC CONVERSION REGISTER 10 DB5 DB4 CONTROL BITS DB3 DB2 DB1 DB0 AE2 AE1 C4(1) C3(0) C2(1) C1(0) REGISTER 11 CONTROL BITS RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 1 0 0 1 1 0 0 0 DB7 DB6 0 0 0 DB5 DB4 0 0 DB3 DB2 DB1 DB0 C4(1) C3(0) C2(1) C1(1) REGISTER 12 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 0 0 0 0 0 1 Figure 29. Register Summary (Register 7 to Register 12) Rev. 0 | Page 17 of 35 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 0 0 1 DB3 DB2 DB1 DB0 C4(1) C3(1) C2(0) C1(0) 12910-035 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 P16 CONTROL BITS RESERVED RESYNC CLOCK CONTROL BITS 16-BIT INTEGER VALUE (INT) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 0 0 0 0 0 0 0 0 0 0 AC1 PR1 N16 N15 N14 N13 N12 N11 N10 N9 N8 N7 DB8 N6 N5 DB7 N4 DB6 N3 N2 PR1 PRESCALER N16 N15 ... N5 N4 N3 N2 N1 0 4/5 0 0 ... 0 0 0 0 0 NOT ALLOWED 1 8/9 0 0 ... 0 0 0 0 1 NOT ALLOWED 0 0 ... 0 0 0 1 0 NOT ALLOWED . . ... . . . . . ... 0 0 ... 1 0 1 1 0 NOT ALLOWED 23 DB4 N1 DB3 DB2 DB1 DB0 C4(0) C3(0) C2(0) C1(0) INTEGER VALUE (INT) 0 0 ... 1 0 1 1 1 VCO AUTOCAL 0 0 ... 1 1 0 0 0 . . ... . . . . . ... 0 DISABLED 1 1 ... 1 1 1 0 1 65533 1 ENABLED 1 1 ... 1 1 1 1 0 65534 1 1 ... 1 1 1 1 1 65535 AC1 DB5 24 INTMIN = 75 WITH PRESCALER = 8/9 12910-036 RESERVED PRESCALER Data Sheet AUTOCAL ADF4355 Figure 30. Register 0 REGISTER 0 Prescaler Control Bits The dual modulus prescaler (P/P + 1), along with the INT, FRACx, and MODx counters, determines the overall division ratio from the VCO output to the PFD input. The PR1 bit (Bit DB20) in Register 0 sets the prescaler value. With Bits[C4:C1] set to 0000, Register 0 is programmed. Figure 30 shows the input data format for programming this register. Reserved Operating at CML levels, the prescaler takes the clock from the VCO output and divides it down for the counters. It is based on a synchronous 4/5 core. When the prescaler is set to 4/5, the maximum RF frequency allowed is 7 GHz. The prescaler limits the INT value; therefore, if P is 4/5, NMIN is 23, and if P is 8/9, NMIN is 75. Bits[DB31:DB22] are reserved and must be set to 0. Automatic Calibration (Autocal) Write to Register 0 to enact (by default) the VCO automatic calibration, and to choose the appropriate VCO and VCO subband. Write 1 to the AC1 bit (Bit DB21) to enable the automatic calibration, which is the recommended mode of operation. 16-Bit Integer Value Set the AC1 bit to 0 to disable the automatic calibration, which leaves the ADF4355 in the same band it is already in when Register 0 is updated. Disable the automatic calibration only for fixed frequency applications, phase adjust applications, or very small (<10 kHz) frequency jumps. Toggling automatic calibration (autocal) is also required when changing frequency (see the Frequency Update Sequence section for additional details). The 16 INT bits (Bits[DB19:DB4]) set the INT value, which determines the integer part of the feedback division factor. The INT value is used in Equation 3 (see the INT, FRACx, MODx, and R Counter Relationship section). All integer values from 23 to 32,767 are allowed for the 4/5 prescaler. For the 8/9 prescaler, the minimum integer value is 75, and the maximum value is 65,535. Rev. 0 | Page 18 of 35 Data Sheet ADF4355 CONTROL BITS DBR 1 24-BIT MAIN FRACTIONAL VALUE (FRAC1) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 F24 F23 F22 F21 F20 F19 F18 F17 F16 F15 F14 F13 F12 F11 F10 F9 F8 F7 F6 F24 F23 .......... F2 F1 MAIN FRACTIONAL VALUE (FRAC1) 0 0 .......... 0 0 0 0 0 .......... 0 1 1 0 0 .......... 1 0 2 0 0 .......... 1 1 3 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 16777212 1 1 .......... 0 1 16777213 1 1 .......... 1 0 16777214 1 1 ......... 1 1 16777215 F5 DB7 DB6 DB5 DB4 F4 1DBR = DOUBLE BUFFERED REGISTER--BUFFERED BY THE WRITE TO REGISTER 0. F3 F2 F1 DB3 DB2 DB1 DB0 C4(0) C3(0) C2(0) C1(1) 12910-037 RESERVED Figure 31. Register 1 REGISTER 1 24-Bit Main Fractional Value Control Bits The 24 FRAC1 bits (Bits[DB27:DB4]) set the numerator of the fraction that is input to the - modulator. This fraction, along with the INT value, specifies the new frequency channel that the synthesizer locks to, as shown in the RF Synthesizer--A Worked Example section. FRAC1 values from 0 to (MOD1 - 1) cover channels over a frequency range equal to the PFD reference frequency. With Bits[C4:C1] set to 0001, Register 1 is programmed. Figure 31 shows the input data format for programming this register. Reserved Bits[DB31:DB28] are reserved and must be set to 0. Rev. 0 | Page 19 of 35 ADF4355 Data Sheet DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 F14 F13 F12 F11 F10 F9 F8 F7 F6 F5 F4 CONTROL BITS 14-BIT AUXILIARY MODULUS VALUE (MOD2) DBR 1 F3 F2 F1 M14 M13 M12 M11 M10 M9 M8 M7 M6 DB8 DB7 DB6 DB5 DB4 M5 M4 M3 M2 M1 DB3 DB2 DB1 DB0 C4(0) C3(0) C2(1) C1(0) F14 F13 .......... F2 F1 FRAC2 WORD M14 M13 .......... M2 M1 MODULUS VALUE (MOD2) 0 0 .......... 0 0 0 0 0 .......... 0 0 NOT ALLOWED 0 0 .......... 0 1 1 0 0 .......... 0 1 NOT ALLOWED 0 0 .......... 1 0 2 0 0 .......... 1 0 2 0 0 .......... 1 1 3 0 0 .......... 1 1 3 . . .......... . . . . . .......... . . . . . .......... . . . . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 16381 1 1 .......... 0 0 16380 1 1 .......... 0 1 16382 1 1 .......... 0 1 16381 1 1 .......... 1 0 16382 1 1 .......... 1 0 16382 1 1 ......... 1 1 16383 1 1 ......... 1 1 16383 1DBR = DOUBLE BUFFERED REGISTER--BUFFERED BY THE WRITE TO REGISTER 0. Figure 32. Register 2 REGISTER 2 14-Bit Auxiliary Modulus Value (MOD2) Control Bits The 14-bit auxiliary modulus value (Bits[DB17:DB4]) sets the auxiliary fractional modulus. Use MOD2 to correct any residual error due to the main fractional modulus. With Bits[C4:C1] set to 0010, Register 2 is programmed. Figure 32 shows the input data format for programming this register. 14-Bit Auxiliary Fractional Value (FRAC2) The 14-bit auxiliary fractional value (Bits[DB31:DB18]) controls the auxiliary fractional word. FRAC2 must be less than the MOD2 value programmed in Register 2. Rev. 0 | Page 20 of 35 12910-038 DBR 1 14-BIT AUXILIARY FRACTIONAL VALUE (FRAC2) ADF4355 PHASE ADJUST PHASE RESYNC SD LOAD RESET RESERVED Data Sheet CONTROL BITS DBR 1 24-BIT PHASE VALUE (PHASE) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 SD1 PR1 PA1 PA1 PR1 SD1 1DBR P24 P23 P22 P21 P20 P19 PHASE ADJUST P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P24 P23 .......... P2 P1 PHASE VALUE (PHASE) 0 DISABLED 0 0 .......... 0 0 0 1 ENABLED 0 0 .......... 0 1 1 0 0 .......... 1 0 2 0 0 .......... 1 1 3 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 16777212 1 1 .......... 0 1 16777213 1 1 .......... 1 0 16777214 1 1 ......... 1 1 16777215 PHASE RESYNC 0 DISABLED 1 ENABLED SD LOAD RESET 0 ON REGISTER0 UPDATE 1 DISABLED P7 P6 P5 P4 P3 P2 P1 DB3 DB2 DB1 DB0 C4(0) C3(0) C2(1) C1(1) 12910-039 0 DB7 DB6 DB5 DB4 = DOUBLE BUFFERED REGISTER--BUFFERED BY THE WRITE TO REGISTER 0. Figure 33. Register 3 REGISTER 3 Control Bits With Bits[C4:C1] set to 0011, Register 3 is programmed. Figure 33 shows the input data format for programming this register. Reserved from the fundamental VCO frequency. This is achieved by programming the D13 bit (Bit DB24) in Register 6 to 0, which ensures divided feedback to the N divider. For resync applications, enable the SD load reset in Register 3 by setting DB30 to 0. Phase Adjust Bit DB31 is reserved and must be set to 0. SD Load Reset When writing to Register 0, the - modulator resets. For applications in which the phase is continually adjusted, this may not be desirable; therefore, in these cases, the - reset can be disabled by writing a 1 to the SD1 bit (Bit DB30). Phase Resync To use the phase resynchronization feature, the PR1 bit (Bit DB29) must be set to 1. If unused, the bit can be programmed to 0. The phase resync timer must also be used in Register 12 to ensure that the resynchronization feature is applied after the PLL has settled to the final frequency. If the PLL has not settled to the final frequency, phase resync may not function correctly. Resynchronization is useful in phased array and beam forming applications. It ensures repeatability of output phase when programming the same frequency. In phase critical applications that use frequencies requiring the output divider (<3400 MHz), it is necessary to feed the N divider with the divided VCO frequency as distinct To adjust the relative output phase of the ADF4355 on each Register 0 update, set the PA1 bit (Bit DB28) to 1. This feature differs from the resynchronization feature in that it is useful when adjustments to phase are made continually in an application. For this function, disable the VCO automatic calibration by setting the AC1 bit (Bit DB21) in Register 0 to 1, and disable the SD load reset by setting the SD1 bit (Bit DB30) in Register 3 to 1. Note that phase resync and phase adjust cannot be used simultaneously. 24-Bit Phase Value The phase of the RF output frequency can adjust in 24-bit steps; from 0 (0) to 360 (224 - 1). For phase adjust applications, the phase is set by (Phase Value/16,777,216) x 360 When the phase value is programmed to Register 3, each subsequent adjustment of Register 0 increments the phase by the value in this equation. Rev. 0 | Page 21 of 35 COUNTER RESET CP THREESTATE DBR 1 POWER-DOWN CURRENT SETTING PD POLARITY DBR 1 10-BIT R COUNTER REF MODE DOUBLE BUFF DBR 1 RDIV2 MUXOUT RESERVED MUX LOGIC Data Sheet REFERENCE DOUBLER DBR 1 ADF4355 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 0 M3 M2 M1 RD2 R10 RD2 REFERENCE DOUBLER 0 DISABLED 1 R9 R8 R7 R6 R5 ENABLED R4 R3 R2 R1 D1 CP4 CP3 COUNTER RESET DISABLED 1 ENABLED 1 DIFF 1 ENABLED CP1 ICP (mA) 5.1k ENABLED 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0.31 0.63 0.94 1.25 1.56 1.88 2.19 2.50 2.81 3.13 3.44 3.75 4.06 4.38 4.69 5.00 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 1020 1 1 .......... 0 1 1021 1 1 .......... 1 0 1022 1 1 .......... 1 1 1023 M3 M2 M1 OUTPUT 0 0 0 THREE-STATE OUTPUT 0 0 1 DVDD 0 1 0 SDGND 0 1 1 R DIVIDER OUTPUT 1 0 0 N DIVIDER OUTPUT 1 0 1 ANALOG LOCK DETECT 1 1 0 DIGITAL LOCK DETECT 1 1 1 RESERVED DB2 0 CP2 .......... DB3 DB1 C4(0) C3(1) C2(0) U1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 U1 REFIN 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 U2 SINGLE CP3 R DIVIDER (R) U3 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 R1 U4 U6 CP4 R2 U5 DISABLED DISABLED .......... U6 DOUBLE BUFFERED REGISTER 6, BITS[DB23:DB21] 0 R9 CP1 0 REFERENCE DIVIDE BY 2 R10 CP2 D1 RD1 1 1DBR RD1 U5 LDP U2 CP THREE-STATE 0 1.8V 0 DISABLED 1 3.3V 1 ENABLED U4 PD POLARITY U3 POWER DOWN 0 NEGATIVE 0 DISABLED 1 POSITIVE 1 ENABLED DB0 C1(0) 12910-040 0 CONTROL BITS = DOUBLE BUFFERED REGISTER--BUFFERED BY THE WRITE TO REGISTER 0. Figure 34. Register 4 REGISTER 4 RDIV2 Control Bits Setting the RD1 bit (Bit DB25) to 1 inserts a divide by 2 toggle flip-flop between the R counter and PFD, which extends the maximum reference frequency input rate. This function provides a 50% duty cycle signal at the PFD input. With Bits[C4:C1] set to 0100, Register 4 is programmed. Figure 34 shows the input data format for programming this register. Reserved 10-Bit R Counter Bits[DB31:DB30] are reserved and must be set to 0. The 10-bit R counter divides the input reference frequency (REFIN) to produce the reference clock to the PFD. Division ratios range from 1 to 1023. MUXOUT The on-chip multiplexer (MUXOUT) is controlled by Bits[DB29:DB27]. For additional details, see Figure 34. Double Buffer Reference Doubler Setting the RD2 bit (Bit DB26) to 0 feeds the REFIN signal directly to the 10-bit R counter, disabling the doubler. Setting this bit to 1 multiplies the reference frequency by a factor of 2 before feeding it into the 10-bit R counter. When the doubler is disabled, the REFIN falling edge is the active edge at the PFD input to the fractional synthesizer. When the doubler is enabled, both the rising and falling edges of the reference frequency become active edges at the PFD input. The D1 bit (Bit DB14) enables or disables double buffering of the RF divider select bits (Bits[DB23:DB21]) in Register 6. The Program Modes section explains how double buffering works. Charge Pump Current Setting The CP4 to CP1 bits (Bits[DB13:DB10]) set the charge pump current. Set this value to the charge pump current that the loop filter is designed with (see Figure 34). For the lowest spurs, the 0.9 mA setting is recommended. The maximum allowable reference frequency when the doubler is enabled is 60 MHz. Rev. 0 | Page 22 of 35 Data Sheet ADF4355 Reference Mode When power-down activates, the following events occur: The ADF4355 permits use of either differential or single-ended reference sources. * For optimum integer boundary spur performance, use the single-ended setting for all references up to 250 MHz (even if using a differential reference signal). Use the differential setting for reference frequencies above 250 MHz. * * * * Level Select The synthesizer counters are forced to their load state conditions. The VCO powers down. The charge pump is forced into three-state mode. The digital lock detect circuitry resets. The RFOUTA+/RFOUTA- and RFOUTB+/RFOUTB- output stages are disabled. The input registers remain active and capable of loading and latching data. * To assist with logic compatibility, MUXOUT is programmable to two logic levels. Set theU5 bit (Bit DB8) to 0 to select 1.8 V logic, and set it to 1 to select 3.3 V logic. Charge Pump Three-State Setting the U2 bit (Bit DB5) to 1 puts the charge pump into three-state mode. Set DB5 to 0 for normal operation. Phase Detector (PD) Polarity The U4 bit (Bit DB7) sets the phase detector polarity. When a passive loop filter or a noninverting active loop filter is used, set DB7 to 1 (positive). If an active filter with an inverting characteristic is used, set this bit to 0 (negative). Counter Reset The U1 bit (Bit DB4) resets the R counter, N counter, and VCO band select of the ADF4355. When DB4 is set to 1, the RF synthesizer N counter and R counter, and the VCO band select, are reset. For normal operation, set DB4 to 0. Toggling counter reset (Bit DB4) is also required when changing frequency (see the Frequency Update Sequence section for additional details). Power-Down The U3 bit (Bit DB6) sets the programmable power-down mode. Setting DB6 to 1 performs a power-down. Setting DB6 to 0 returns the synthesizer to normal operation. In software powerdown mode, the ADF4355 retains all information in its registers. The register contents are only lost if the supply voltages are removed. REGISTER 5 The bits in Register 5 are reserved and must be programmed as described in Figure 35, using a hexadecimal word of 0x00800025. DB31 DB30 DB29 DB28 DB27 DB26 0 0 0 0 0 0 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Figure 35. Register 5 (0x00800025) Rev. 0 | Page 23 of 35 0 0 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 0 1 0 DB3 DB2 DB1 DB0 C4(0) C3(1) C2(0) C1(1) 12910-041 CONTROL BITS RESERVED AUX RF OUTPUT POWER RF OUTPUT ENABLE AUX RF OUTPUT ENABLE CHARGE PUMP BLEED CURRENT RESERVED RF OUTPUT POWER CONTROL BITS DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 BL10 BL9 1 0 1 0 D13 D12 D11 D10 BL8 BL7 BL5 BL6 BL4 BL3 BL2 BL1 1 D8 0 D6 D5 D4 D3 FEEDBACK D13 SELECT 0 1 DIVIDED FUNDAMEN TAL BL9 BLEED CURRENT 0 1 DISABLED ENABLED BL10 GATED BLEED 0 1 DISABLED ENABLED D12 D11 D10 RF DIVIDER SELECT 0 0 0 /1 0 0 1 /2 0 1 0 /4 0 1 1 1 0 1 0 1 1 D8 MUTE TILL LOCK DETECT /8 0 MUTE DISABLED 0 /16 1 MUTE ENABLED 1 /32 0 /64 BL8 1BITS[DB23:DB21] BL7 .......... BL2 BL1 0 0 .......... 0 1 1 (3.75A) 0 0 .......... 1 0 2 (7.5A) . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 252 (945A) 1 1 .......... 0 1 253 (948.75A) 1 1 .......... 1 0 254 (952.5A) 1 1 .......... 1 1 255 (956.25A) D2 D1 DB2 DB1 D2 D1 OUTPUT POWER 0 0 -4dBm 0 1 -1dBm 1 0 +2dBm 1 1 +5dBm D3 RF OUT 0 DISABLED 1 ENABLED D5 D4 AUXILIARY OUTPUT POWER 0 0 -4dBm 0 1 -1dBm 1 0 +2dBm 1 1 +5dBm D6 AUXILIARY OUT 0 DISABLED 1 ENABLED DB0 C4(0) C3(1) C2(1) C1(0) BLEED CURRENT ARE BUFFERED BY A WRITE TO REGISTER 0 WHEN THE DOUBLE BUFFER BIT IS ENABLED, BIT DB14 OF REGISTER 4. 12910-042 RF DIVIDER SELECT1 MTLD RESERVED RESERVED FEEDBACK SELECT Data Sheet NEGATIVE BLEED GATED BLEED RESERVED ADF4355 Figure 36. Register 6 REGISTER 6 Reserved Control Bits Bits[DB28:DB25] are reserved and must be set to 1010. With Bits[C4:C1] set to 0110, Register 6 is programmed. Figure 36 shows the input data format for programming this register. Feedback Select Reserved Bit DB31 is reserved and must be set to 0. Gated Bleed Bleed currents can be used for improving phase noise and spurs; however, due to a potential impact on lock time, the gated bleed bit, BL10 (Bit DB30), if set to 1, ensures bleed currents are not switched on until the digital lock detect asserts logic high. Note that this function requires digital lock detect to be enabled. Negative Bleed Use of constant negative bleed is recommended for most applications because it improves the linearity of the charge pump leading to lower noise and spurs than leaving negative bleed off. To enable negative bleed, write 1 to BL9 (Bit DB29), and to disable negative bleed, write 0 to BL9 (Bit DB29). D13 (Bit DB24) selects the feedback from the output of the VCO to the N counter. When D13 is set to 1, the signal is taken directly from the VCO. When this bit is set to 0, the signal is taken from the output of the output dividers. The dividers enable coverage of the wide frequency band (54 MHz to 6800 MHz). When the divider is enabled and the feedback signal is taken from the output, the RF output signals of two separately configured PLLs are in phase. Divided feedback is useful in some applications where the positive interference of signals is required to increase the power. RF Divider Select D12 to D10 (Bits[DB23:DB21]) select the value of the RF output divider (see Figure 36). Rev. 0 | Page 24 of 35 Data Sheet ADF4355 Charge Pump Bleed Current Reserved BL8 to BL1 (Bits[DB20:DB13]) control the level of the bleed current added to the charge pump output. This current optimizes the phase noise and spurious levels from the device. Bit DB10 is reserved and must be set to 1. Tests have shown that the optimal bleed set is the following: 4/N < IBLEED/ICP < 10/N where: IBLEED is the value of constant negative bleed applied to the charge pump, which is set by the contents of Bits[BL8:BL1]. ICP is the value of charge pump current setting, Bits[DB13:DB10] of Register 4. N is the value of the feedback counter from the VCO to the PFD. Reserved Bit DB12 is reserved and must be set to 0. Mute Till Lock Detect When D8 (Bit DB11) is set to 1, the supply current to the RF output stage is shut down until the device achieves lock, as determined by the digital lock detect circuitry. Auxiliary RF Output Enable Bit DB9 enables or disables the auxiliary frequency RF output (RFOUTB+/RFOUTB-). When DB9 is set to 1, the auxiliary frequency RF output is enabled. When DB9 is set to 0, the auxiliary RF output is disabled. Auxiliary RF Output Power Bits[DB8:DB7] set the value of the auxiliary RF output power level (see Figure 36). RF Output Enable Bit DB6 enables or disables the primary RF output (RFOUTA+/ RFOUTA-). When DB6 is set to 0, the primary RF output is disabled. When DB6 is set to 1, the primary RF output is enabled. Output Power Bits[DB5:DB4] set the value of the primary RF output power level (see Figure 36). Rev. 0 | Page 25 of 35 LD MODE LD CYCLE COUNT RESERVED LOL MODE DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 1 0 0 LE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 LD5 LD4 LOL LD3 LE SYNCHRONIZ ATION DB3 DB2 DB1 DB0 LD2 LD1 C4(0) C3(1) C2(1) C1(1) LD1 LE CONTROL BITS LOCK DETECT MODE 0 FRACTIONAL-N 1 INTEGER-N (2.9ns) LD3 LD2 FRACTIONAL-N LD PRECISION 0 0 5.0ns 0 1 6.0ns 1 0 8.0ns 1 1 12.0ns LOL LOSS OF LOCK MODE 0 DISABLED 0 DISABLED 1 LE SYNCED TO REFIN 1 ENABLED LD5 LD4 LOCK DETECT CYCLE COUNT 0 0 1024 0 1 2048 1 0 4096 1 1 8192 12910-043 RESERVED FRAC-N LD PRECISION Data Sheet LE SYNC ADF4355 Figure 37. Register 7 REGISTER 7 Loss of Lock Mode Control Bits Set LOL (Bit DB7) to 1 when the application is a fixed frequency application in which the reference (REFIN) is likely to be removed, such as a clocking application. The standard lock detect circuit assumes that REFIN is always present; however, this may not be the case with clocking applications. To enable this functionality, set DB7 to 1. With Bits[C4:C1] set to 0111, Register 7 is programmed. Figure 37 shows the input data format for programming this register. Reserved Bits[DB31:DB29] are reserved and must be set to 0. Bit DB28 is reserved and must be set to 1. Bits[DB27:DB26] are reserved and must be set to 0. LE Sync When set to 1, Bit DB25 ensures that the load enable (LE) edge is synchronized internally with the rising edge of reference input frequency. This synchronization prevents the rare event of reference and RF dividers loading at the same time as a falling edge of reference frequency, which can lead to longer lock times. Reserved Bits[DB24:DB10] are reserved and must be set to 0. Fractional-N Lock Detect Precision (LDP) LD3 and LD2 (Bits[DB6:DB5]) set the precision of the lock detect circuitry in fractional-N mode. LDP is available at 5.0 ns, 6.0 ns, 8.0 ns, or 12.0 ns. If bleed currents are used, use 12 ns. Lock Detect Mode (LDM) If LD1 (Bit DB4) is set to 0, each reference cycle is set by fractional-N lock detect precision as described in the Fractional-N Lock Detect Count (LDC) section. If DB4 is set to 1, each reference cycle is 2.9 ns long, which is more appropriate for integer-N applications. Fractional-N Lock Detect Count (LDC) LD5 and LD4 (Bits[DB9:DB8]) set the number of consecutive cycles counted by the lock detect circuitry before asserting lock detect high. See Figure 37 for details. Rev. 0 | Page 26 of 35 Data Sheet ADF4355 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 0 0 1 0 0 0 0 0 0 0 1 0 1 1 0 1 0 0 0 0 0 1 0 0 0 1 0 DB3 0 DB2 DB1 DB0 C4(1) C3(0) C2(0) C1(0) 12910-044 CONTROL BITS RESERVED Figure 38. Register 8 (0x102D0428) SYNTHESIZER LOCK TIMEOUT AUTOMATIC LEVEL TIMEOUT TIMEOUT DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 VC8 VC7 VC6 VC5 VC4 VC3 VC2 VC1 TL10 TL9 TL8 TL7 TL6 TL5 TL4 TL3 TL2 TL1 AL5 AL4 AL3 AL2 TL9 .......... TL2 TL1 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 1020 1 1 .......... 0 1 1021 1 1 .......... 1 0 1022 1 1 .......... 1 1 1023 TL10 VC8 VC7 .......... VC2 VC1 0 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 252 1 1 .......... 0 1 253 1 1 .......... 1 0 254 1 1 .......... 1 1 255 TIMEOUT AL5 VCO BAND DIV SL5 DB7 DB6 DB5 DB4 SL4 SL2 SL3 DB3 SL4 .......... SL2 SL1 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 28 1 1 .......... 0 1 29 1 1 .......... 1 0 30 1 1 .......... 1 1 31 ALC WAIT AL4 .......... AL2 AL1 0 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . .......... . . . 1 1 .......... 0 0 28 1 1 .......... 0 1 29 1 1 .......... 1 0 30 1 1 .......... 1 1 31 DB2 DB1 DB0 SL1 C4(1) C3(0) C2(0) C1(1) 0 SL5 0 AL1 CONTROL BITS SLC WAIT . 12910-045 VCO BAND DIVISION Figure 39. Register 9 REGISTER 8 Automatic Level Calibration Timeout The bits in this register are reserved and must be programmed as described in Figure 38, using a hexadecimal word of 0x102D0428. AL5 to AL1 (Bits[DB13:DB9]) set the timer value used for the automatic level calibration of the VCO. This function combines the PFD frequency, the timeout variable, and ALC wait variable. Choose ALC such that the following equation is always greater than 50 s. REGISTER 9 Control Bits With Bits[C4:C1] set to 1001, Register 9 is programmed. Figure 39 shows the input data format for programming this register. VCO Band Division VC8 to VC1 (Bits[DB31:DB24]) set the value of the VCO band division clock. Determine the value of this clock by PFD/(band division x 16) such that the result is <150 kHz. (Timeout x ALC Wait/PFD Frequency) > 50 s Synthesizer Lock Timeout SL5 to SL1 (Bits[DB8:DB4]) set the synthesizer lock timeout value. Use this value to allow the VTUNE force to settle on the VTUNE pin. The value must be 20 s. Calculate the value using the following equation: Timeout TL10 to TL1 (Bits[DB23:DB14]) set the timeout value for the VCO band select. Use this value as a variable in the other VCO calibration settings. Rev. 0 | Page 27 of 35 (Timeout x Synthesizer Lock Timeout/PFD Frequency) > 20 s ADC CLOCK DIVIDER DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 AD8 AD7 AD6 AD5 AD4 DB7 DB6 AD3 AD2 AD7 .......... AD2 0 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 252 1 1 .......... 0 1 253 1 1 .......... 1 0 254 1 1 .......... 1 1 255 AD8 DB5 DB4 AD1 CONTROL BITS DB3 DB2 DB1 DB0 AE2 AE1 C4(1) C3(0) C2(1) C1(0) AE1 ADC 0 DISABLED 1 ENABLED AE2 ADC CONVERSION 0 DISABLED 1 ENABLED AD1 ADC CLK DIV 12910-047 RESERVED ADC ENABLE Data Sheet ADC CONVERSION ADF4355 Figure 40. Register 10 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 1 0 0 1 1 0 0 0 0 0 0 0 0 DB3 DB2 DB1 DB0 C4(1) C3(0) C2(1) C1(1) 12910-048 CONTROL BITS RESERVED Figure 41. Register 11 (0x0061300B) AD8 to AD1 (Bits[DB13:DB6]) set the value of this divider. On power-up, the R counter is not programmed; however, in these power-up cases, it defaults to R = 1. REGISTER 10 Control Bits With Bits[C4:C1] set to 1010, Register 10 is programmed. Figure 40 shows the input data format for programming this register. Choose ADC_CLK_DIV such that PFD/((ADC_CLK_DIV x 4) + 2) < 100 kHz Reserved ADC Conversion Enable Bits[DB31:DB14] are reserved. Bits[DB23:DB22] must be set to 11, but all other bits in this range must be set to 0. AE2 (Bit DB5) ensures that the ADC performs a conversion when a write to Register 10 is performed. It is recommended to enable this mode. ADC Clock Divider (ADC_CLK_DIV) An on-board analog-to-digital converter (ADC) determines the VTUNE setpoint relative to the ambient temperature of the ADF4355 environment. The ADC ensures that the initial tuning voltage in any application is chosen correctly to avoid any temperature drift issues. The ADC uses a clock that is equal to the output of the R counter (or the PFD frequency) divided by ADC_CLK_DIV. ADC Enable AE1 (Bit DB4), when set to 1, powers up the ADC for the temperature dependent VTUNE calibration. It is recommended to always use this function. REGISTER 11 The bits in this register are reserved and must be programmed as described in Figure 41, using a hexadecimal word of 0x0061300B. Rev. 0 | Page 28 of 35 Data Sheet ADF4355 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 P15 P14 P13 P12 P11 P10 P8 P9 P7 P6 P5 P4 P3 P2 P16 P15 ... P5 P4 P3 P2 P1 RESYNC CLOCK 0 0 ... 0 0 0 0 0 NOT ALLOWED 0 0 ... 0 0 0 0 1 1 0 0 ... 0 0 0 1 0 2 . . ... . . . . . ... 0 0 ... 1 0 1 1 0 22 0 0 ... 1 0 1 1 1 23 0 0 ... 1 1 0 0 0 24 . . ... . . . . . ... 1 1 ... 1 1 1 0 1 65533 1 1 ... 1 1 1 1 0 65534 1 1 ... 1 1 1 1 1 65535 P1 0 0 0 0 0 1 DB9 DB8 DB7 DB6 DB5 DB4 0 0 0 0 0 1 DB3 DB2 DB1 DB0 C4(1) C3(1) C2(0) C1(0) 12910-049 P16 CONTROL BITS RESERVED RESYNC CLOCK Figure 42. Register 12 REGISTER 12 FREQUENCY UPDATE SEQUENCE Control Bits Frequency updates require updating the auxiliary modulator (MOD2) in Register 2, the fractional value (FRAC1) in Register 1, and the integer value (INT) in Register 0. A counter reset (Bit DB4) is also required in the frequency update sequence. Therefore, the sequence must be as follows: With Bits[C4:C1] set to 1100, Register 12 is programmed. Figure 42 shows the input data format for programming this register. Phase Resync Clock Divider Value P16 to P1 (Bits[DB31:DB16]) set the timeout counter for activation of phase resync. This value must be set such that a resync happens immediately after (and not before) the PLL has achieved lock after reprogramming. Calculate the timeout value using the following equation: 1. 2. 3. 4. 5. 6. Time Out Value = Phase Resync Clock/PFD Frequency 7. Reserved Bits[DB15:DB4] are reserved. Bit DB10 and Bit DB4 must be set to 1, but all other bits in this range must be set to 0. The frequency change occurs on the second write to Register 0. REGISTER INITIALIZATION SEQUENCE At initial power-up, after the correct application of voltages to the supply pins, program the ADF4355 registers in the following sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Register 4 (counter reset enabled [DB4 = 1]) Register 2 Register 1 Register 0 (autocal disabled [DB21 = 0]) Register 4 (counter reset disabled [DB4 = 0]) Wait > 16 ADC_CLK cycles. For example, if ADC_CLK = 99.417 kHz, wait 16/99417 sec = 161 s. See Register 10. Register 0 (autocal enabled [DB21 = 1]) Register 12 Register 11 Register 10 Register 9 Register 8 Register 7 Register 6 Register 5 Register 4 Register 3 Register 2 Register 1 Register 0 Rev. 0 | Page 29 of 35 ADF4355 Data Sheet RF SYNTHESIZER--A WORKED EXAMPLE The worked example is as follows: Use the following equations to program the ADF4355 synthesizer: * FRAC2 FRAC1 + MOD2 x (fPFD)/RF Divider RFOUT = INT + MOD1 (7) where: RFOUT is the RF frequency output. INT is the integer division factor. FRAC1 is the fractionality. FRAC2 is the auxiliary fractionality. MOD2 is the auxiliary modulus. MOD1 is the fixed 24-bit modulus. RF Divider is the output divider that divides down the VCO frequency. fPFD = REFIN x ((1 + D)/(R x (1 + T))) * From Equation 8, fPFD = (122.88 MHz x (1 + 0)/2) = 61.44 MHz (8) where: REFIN is the reference frequency input. D is the RF REFIN doubler bit. R is the RF reference division factor. T is the reference divide by 2 bit (0 or 1). For example, in a universal mobile telecommunication system (UMTS) where 2112.8 MHz RF frequency output (RFOUT) is required, a 122.88 MHz reference frequency input (REFIN) is available. Note that the ADF4355 VCO operates in the frequency range of 3.4 GHz to 6.8 GHz. Therefore, an RF divider of 2 must be used (VCO frequency = 4225.6 MHz, RFOUT = VCO frequency/ RF divider = 4225.6 MHz/2 = 2112.8 MHz). The feedback path is also important. In this example, the VCO output is fed back before the output divider (see Figure 43). In this example, divide the 122.88 MHz reference signal by 2 to generate a fPFD of 61.44 MHz. The desired channel spacing is 200 kHz. PFD VCO /2 RFOUT N DIVIDER Figure 43. Loop Closed Before Output Divider 12910-148 fPFD * * * * * * N = VCOOUT/fPFD = 4225.6 MHz/61.44 MHz = 68.7760416666666667 INT = int(VCO frequency/fPFD) = 68 FRAC = 0.7760416666666667 MOD1 = 16,777,216 FRAC1 = int(MOD1 x FRAC) = 13019817 Remainder = 0.6666666667 or 2/3 MOD2 = fPFD/GCD(fPFD/fCHSP) = 61.44 MHz / GCD(61.44 MHz/200 kHz) = 1536 FRAC2 = remainder x 1536 = 1024 2112.8 MHz = 61.44 MHz x ((INT + (FRAC1 + FRAC2/MOD2)/224))/2 (9) (10) where: INT = 68 FRAC1 = 13,019,817 MOD2 = 1536 FRAC2 = 1024 RF Divider = 2 REFERENCE DOUBLER AND REFERENCE DIVIDER The on-chip reference doubler allows the input reference signal to be doubled. The doubler is useful for increasing the PFD comparison frequency. To improve the noise performance of the system, increase the PFD frequency. Doubling the PFD frequency usually improves noise performance by 3 dB. The reference divide by 2 divides the reference signal by 2, resulting in a 50% duty cycle PFD frequency. SPURIOUS OPTIMIZATION AND FAST LOCK Narrow loop bandwidths can filter unwanted spurious signals, but these bandwidths usually have a long lock time. A wider loop bandwidth achieves faster lock times but may lead to increased spurious signals inside the loop bandwidth. OPTIMIZING JITTER For lowest jitter applications, use the highest possible PFD frequency to minimize the contribution of in-band noise from the PLL. Set the PLL filter bandwidth such that the in-band noise of the PLL intersects with the open-loop noise of the VCO, minimizing the contribution of both to the overall noise. Use the ADIsimPLL design tool for this task. Rev. 0 | Page 30 of 35 Data Sheet ADF4355 SPUR MECHANISMS Synthesizer Lock Timeout This section describes the two different spur mechanisms that arise with a fractional-N synthesizer and how to minimize them in the ADF4355. The synthesizer lock timeout ensures that the VCO calibration DAC, which forces VTUNE, has settled to a steady value for the band select circuitry. Integer Boundary Spurs The timeout and synthesizer lock timeout variables programmed in Register 9 select the length of time the DAC is allowed to settle to the final voltage before the VCO calibration process continues to the next phase, which is VCO band selection. The PFD frequency is used as the clock for this logic, and the duration is set by One mechanism for fractional spur creation is the interactions between the RF VCO frequency and the reference frequency. When these frequencies are not integer related (the purpose of a fractional-N synthesizer), spur sidebands appear on the VCO output spectrum at an offset frequency that corresponds to the beat note or the difference in frequency between an integer multiple of the reference and the VCO frequency. These spurs are attenuated by the loop filter and are more noticeable on channels close to integer multiples of the reference where the difference frequency can be inside the loop bandwidth (thus the name, integer boundary spurs). Reference Spurs Reference spurs are generally not a problem in fractional-N synthesizers because the reference offset is far outside the loop bandwidth. However, any reference feedthrough mechanism that bypasses the loop may cause a problem. Feedthrough of low levels of on-chip reference switching noise, through the prescaler back to the VCO, can result in reference spur levels as high as -80 dBc. LOCK TIME The PLL lock time divides into a number of settings. All of these are modeled in the ADIsimPLL design tool. Faster lock times than those detailed in this data sheet are possible; contact your local Analog Devices, Inc., sales representative for more information. Lock Time--A Worked Example Assuming fPFD = 61.44 MHz, Timeout x Synthesizer Lock Timeout PFD Frequency The calculated time must be equal to or greater than 20 s. VCO Band Selection Use the PFD frequency again as the clock for the band selection process. Calculate this value by PFD/(VCO Band Selection x 16) < 150 kHz The band selection takes 11 cycles of the previously calculated value. Calculate the duration by 11 x (VCO Band Selection x 16)/PFD Frequency Automatic Level Calibration Timeout Use the automatic level calibration (ALC) function to choose the correct bias current in the ADF4355 VCO core. Calculate the time taken by 5 x 11 x ALC Wait x Timeout/PFD Frequency PLL Low-Pass Filter Settling Time The time taken for the loop to settle is inversely proportional to the low-pass filter bandwidth. The settling time is also modeled in the ADIsimPLL design tool. The total lock time for changing frequencies is the sum of the four separate times (synthesizer lock, VCO band selection, ALC timeout, and PLL settling time) and is all modeled in the ADIsimPLL design tool. VCO Band Div = Ceiling(fPFD/2,400,000) = 26 where Ceiling() rounds up to the nearest integer. By combining the following two equations: ALC Wait > (50 s x fPFD)/Timeout Synthesizer Lock Timeout > (20 s x fPFD)/Timeout The following is found: ALC Wait = 2.5 x Synthesizer Lock Timeout Maximize ALC Wait (to reduce Timeout to minimize time) so that ALC Wait = 30 and Synthesizer Lock Timeout = 12. Finally, ALC Wait > (50 s x fPFD)/Timeout, is rearranged as Timeout = Ceiling((fPFD x 50 s)/ALC Wait) Timeout = Ceiling((61.44 MHz x 50 s)/30) = 103 Rev. 0 | Page 31 of 35 ADF4355 Data Sheet APPLICATIONS INFORMATION DIRECT CONVERSION MODULATOR The LO ports of the ADL5375 can be driven differentially from the complementary RFOUTA+/RFOUTA- outputs of the ADF4355. Differential drive gives better second-order distortion performance than a single-ended LO driver and eliminates the use of a balun to convert from a single-ended LO input to the more desirable differential LO input for the ADL5375. Direct conversion architectures are increasingly being used to implement base station transmitters. Figure 44 shows how to use Analog Devices devices to implement such a system. The circuit block diagram shows the AD9761 TxDAC+(R) being used with the ADL5375. The use of a dual integrated DAC, such as the AD9761, ensures minimum error contribution (over temperature) from this portion of the signal chain. The ADL5375 accepts LO drive levels from -6 dBm to +6 dBm. The optimum LO power can be software programmed on the ADF4355, which allows levels from -4 dBm to +5 dBm from each output. The local oscillator (LO) is implemented using the ADF4355. The low-pass filter was designed using the ADIsimPLL design tool for a PFD of 61.44 MHz and a closed-loop bandwidth of 20 kHz. 51 REFIO 51 IOUTA MODULATED DIGITAL DATA AD9761 The RF output is designed to drive a 50 load; however, it must be ac-coupled, as shown in Figure 44. If the I and Q inputs are driven in quadrature by 2 V p-p signals, the resulting output power from the ADL5375 modulator is approximately 2 dBm. LOW-PASS FILTER IOUTB TxDAC QOUTA LOW-PASS FILTER QOUTB FSADJ 51 51 2k FREF IN FREF IN VDD 1nF 1nF 100nF 100nF LOCK DETECT 25 30 CREG1 MUXOUT 17 10 26 32 5 4 27 6 16 VVCO VP AV DD DVDD AV DD CE PDB RF VRF CREG2 RFOUTB+ 14 1nF 1nF RFOUTB- 15 28 REF INB SPI-COMPATIBLE SERIAL BUS IBBN VOUT 7.5nH 1 CLK 7.5nH 1nF 2 DATA RFOUTA+ 11 ADF4355 3 LE LOIN 1nF VTUNE 20 4.7k 1500pF CPGND SDGND AGND AGNDRF AGNDVCO VREGVCO 31 9 13 18 21 10pF VREF VBIAS 23 24 19 0.1F 10pF LPF 33nF QUADRATURE PHASE SPLITTER RFOUT DSOP 3.3k CPOUT 7 22 RSET LOIP LPF RFOUTA- 12 8 ADL5375 IBBP 29 REF A IN QBBN 390pF QBBP 1k 0.1F 10pF 0.1F Figure 44. Direct Conversion Modulator Rev. 0 | Page 32 of 35 12910-138 VVCO Data Sheet ADF4355 POWER SUPPLIES To improve the thermal performance of the package, use thermal vias on the PCB thermal pad. If vias are used, incorporate them into the thermal pad at the 1.2 mm pitch grid. The via diameter must be between 0.3 mm and 0.33 mm, and the via barrel must be plated with 1 oz. of copper to plug the via. The ADF4355 contains four multiband VCOs that together cover an octave range of frequencies. To ensure best performance, it is vital to connect a low noise regulator, such as the ADM7150, to the VVCO pin. Connect the same regulator to VREGVCO and VP. For a microwave PLL and VCO synthesizer, such as the ADF4355, take care with the board stack-up and layout. Do not consider using FR4 material because it is too lossy above 3 GHz. Instead, Rogers 4350, Rogers 4003, or Rogers 3003 dielectric material is suitable. For the 3.3 V supply pins, use one or two ADM7150 regulators. Figure 45 shows the recommended connections. PRINTED CIRCUIT BOARD (PCB) DESIGN GUIDELINES FOR A CHIP-SCALE PACKAGE The lands on the 32-lead lead frame chip-scale package are rectangular. The PCB pad for these lands must be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. Center each land on the pad to maximize the solder joint size. Take care with the RF output traces to minimize discontinuities and ensure the best signal integrity. Via placement and grounding are critical. The bottom of the chip-scale package has a central exposed thermal pad. The thermal pad on the PCB must be at least as large as the exposed pad. On the PCB, there must be a minimum clearance of 0.25 mm between the thermal pad and the inner edges of the pad pattern. This clearance ensures the avoidance of shorting. VIN CIN 1F ON OFF CBYP 1F EN VOUT ADM7150 VOUT = 3.3V COUT 1F 100nF REF BYP VREG CREG 10F 25 30 CREG1 MUXOUT 17 REF_SENSE GND FREF IN FREF IN 1nF 1nF LOCK DETECT 100nF 10 26 4 27 6 32 16 VVCO VP DVDD AVDD CE PDB RF VRF CREG2 29 REF INA RFOUTB+ 14 1nF 1nF RFOUTB- 15 28 REF INB 7.5nH VIN CIN 1F ON OFF CBYP 1F EN VOUT ADM7150 REF BYP VREG CREG 10F REF_SENSE GND VOUT = 5.0V COUT 1F SPI-COMPATIBLE SERIAL BUS 1 CLK VIN = 6.0V VOUT 7.5nH 1nF 2 DATA RFOUTA+ 11 ADF4355 3 LE RFOUTA- 12 1nF VTUNE 20 3.3k CPOUT 7 22 RSET 4.7k AVDD 5 CPGND SDGND AGND AGNDRF AGNDVCO VREGVCO 8 31 9 13 18 21 10pF Figure 45. ADF4355 Power Supplies Rev. 0 | Page 33 of 35 VREF 19 33nF 390pF 1k VBIAS 23 0.1F 1500pF 24 10pF 0.1F 10pF 0.1F 12910-050 VIN = 6.0V ADF4355 Data Sheet OUTPUT MATCHING The low frequency output can simply be ac-coupled to the next circuit, if desired; however, if higher output power is required, use a pull-up inductor to increase the output power level. VRF 7.5nH 50 Figure 46. Optimum Output Stage 12910-051 100pF RFOUTA+ When differential outputs are not needed, terminate the unused output or combine it with both outputs using a balun. For lower frequencies below 2 GHz, it is recommended to use a 100 nH inductor on the RFOUTA+/RFOUTA- pins. The RFOUTA+/RFOUTA- pins are a differential circuit. Provide each output with the same (or similar) components where possible, such as the same shunt inductor value, bypass capacitor, and termination. The auxiliary frequency output, RFOUTB+/RFOUTB-, can be treated the same as the RFOUTA+/RFOUTA- output. If unused, leave both RFOUTB+/RFOUTB- pins open. Rev. 0 | Page 34 of 35 Data Sheet ADF4355 OUTLINE DIMENSIONS 0.30 0.25 0.18 32 25 1 24 0.50 BSC *3.75 3.60 SQ 3.55 EXPOSED PAD 17 TOP VIEW 0.80 0.75 0.70 0.50 0.40 0.30 8 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PIN 1 INDICATOR 9 BOTTOM VIEW 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. *COMPLIANT TO JEDEC STANDARDS MO-220-WHHD-5 WITH THE EXCEPTION OF THE EXPOSED PAD DIMENSION. 08-16-2010-B PIN 1 INDICATOR 5.10 5.00 SQ 4.90 Figure 47. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm x 5 mm Body, Very, Very Thin Quad (CP-32-12) Dimensions shown in millimeters ORDERING GUIDE Model1 ADF4355BCPZ ADF4355BCPZ-RL7 EV-ADF4355SD1Z 1 Temperature Range -40C to +85C -40C to +85C Package Description 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] Evaluation Board Z = RoHS Compliant Part. (c)2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D12910-0-4/15(0) Rev. 0 | Page 35 of 35 Package Option CP-32-12 CP-32-12 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADF4355BCPZ-RL7 ADF4355BCPZ EV-ADF4355SD1Z