1
Motorola Optoelectronics Device Data
  ! !
! "!"!
   !
The MOC8020 and MOC8021 devices consist of a gallium arsenide infrared
emitting diode optically coupled to a monolithic silicon photodarlington detector .
The chip to Pin 6 base connection has been eliminated to improve the device’s
output performance in higher noise environments.
•No Base Connection for Improved Noise Immunity
•Higher Sensitivity to Low Input Drive Current
•
To order devices that are tested and marked per VDE 0884 requirements, the
suffix ”V” must be included at end of part number. VDE 0884 is a test option.
Applications
•Appliances, Measuring Instruments
•I/O Interfaces for Computers
•Programmable Controllers
•Portable Electronics
•Interfacing and coupling systems of different potentials and impedances
•Solid State Relays
•Circuits Exposed to High Noise Environments
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Rating Symbol Value Unit
INPUT LED
Reverse Voltage VR3 Volts
Forward Current — Continuous IF60 mA
LED Power Dissipation @ TA = 25°C
with Negligible Power in Output Detector
Derate above 25°C
PD120
1.41
mW
mW/°C
OUTPUT DETECTOR
Collector–Emitter Voltage VCEO 50 Volts
Collector Current Continuous IC 150 mA
Emitter–Collector Voltage VECO 5 Volts
Detector Power Dissipation @ TA = 25°C
with Negligible Power in Input LED
Derate above 25°C
PD150
1.76
mW
mW/°C
TOTAL DEVICE
Isolation Surge Voltage(1)
(Peak ac Voltage, 60 Hz, 1 sec Duration) VISO 7500 Vac(pk)
Total Device Power Dissipation @ TA = 25°C
Derate above 25°CPD250
2.94 mW
mW/°C
Ambient Operating Temperature Range(2) TA–55 to +100 °C
Storage Temperature Range(2) Tstg –55 to +150 °C
Soldering Temperature (10 sec, 1/16″ from case) TL260 °C
1. Isolation surge voltage is an internal device dielectric breakdown rating.
1. For this test, Pins 1 and 2 are common, and Pins 4 and 5 are common.
2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.
GlobalOptoisolator is a trademark of Motorola, Inc.
Order this document
by MOC8020/D

SEMICONDUCTOR TECHNICAL DATA
GlobalOptoisolator
Motorola, Inc. 1995


SCHEMATIC
[CTR = 1000% Min]
STANDARD THRU HOLE
CASE 730A–04
STYLE 3 PLASTIC
PIN 1. LED ANODE
2. LED CATHODE
3. N.C.
4. EMITTER
5. COLLECTOR
6. N.C.
[CTR = 500% Min]
1
2
3
6
5
4
61
REV 1
 
2 Motorola Optoelectronics Device Data
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)(1)
Characteristic Symbol Min Typ(1) Max Unit
INPUT LED
Reverse Leakage Current
(VR = 3 V) IR— 0.05 10 µA
Forward Voltage
(IF = 10 mA) VF— 1.15 2 Volts
Capacitance
(V = 0 V, f = 1 MHz) C — 18 — pF
PHOTODARLINGTON (TA = 25°C and IF = 0, unless otherwise noted)
Collector–Emitter Dark Current
(VCE = 10 V) ICEO — — 100 nA
Collector–Emitter Base Breakdown Voltage
(IC = 1 mA) V(BR)CEO 50 — — Volts
Emitter–Collector Breakdown Voltage
(IE = 100 µA) V(BR)ECO 5 — — Volts
COUPLED (TA = 25°C unless otherwise noted)
Collector Output Current
(VCE = 5 V, IF = 10 mA) MOC8020
MOC8021
IC (CTR)(2) 50 (500)
100 (1000) —
——
—
mA (%)
Isolation Surge Voltage(3,4), 60 Hz Peak ac, 1 Second VISO 7500 — — Vac(pk)
Isolation Resistance(3)
(V = 500 V) RISO — 1011 — Ohms
Isolation Capacitance(3)
(V = 0, f = 1 MHz) CISO — 0.2 — pF
SWITCHING
Turn–On Time ton — 3.5 —
µs
Turn–Off Time
VCC = 10 V, RL = 100 Ω, IF = 5 mA(5)
toff — 95 —
Rise Time
VCC = 10 V, RL = 100 Ω, IF = 5 mA(5)
tr— 1 —
Fall Time tf— 2 —
1. Always design to the specified minimum/maximum electrical limits (where applicable).
2. Current Transfer Ratio (CTR) = IC/IF x 100%.
3. For this test, LED Pins 1 and 2 are common and Phototransistor Pins 4 and 5 are common.
4. Isolation Surge Voltage, VISO, is an internal device dielectric breakdown rating.
5. For test circuit setup and waveforms, refer to Figure 9.
TYPICAL CHARACTERISTICS
TA = –55
°
C THRU
+100
°
C
+25
°
C
Figure 1. LED Forward Voltage versus Forward Current Figure 2. Output Current versus Input Current
2
1.8
1.6
1.4
1.2
11 10 100 1000
IF, LED FORWARD CURRENT (mA)
25
°
C
100
°
C
VF, FORWARD VOLTAGE (VOLTS)
IC, OUTPUT COLLECTOR CURRENT (NORMALIZED)
10
1
0.1
0.01 0.5 1 2 5 10 20 50
IF, LED INPUT CURRENT (mA)
NORMALIZED TO: IF = 10 mA
TA = –55
°
C
+70
°
C
TA = 25
°
C
PULSE ONLY
PULSE OR DC
 
3
Motorola Optoelectronics Device Data
, COLLECTOR CURRENT (mA)
20
0
Figure 3. Collector Current versus
Collector–Emitter Voltage
IF = 10 mA
0
VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS)
IC
40
60
80
100
120
140
1 2 3 4 5 6 7 8 9 10
5 mA
2 mA
1 mA
10
7
5
2
1
0.7
0.5
0.2
0.1 – 60
Figure 4. Output Current versus Ambient Temperature
– 40 – 20
C, OUTPUT COLLECTOR CURRENT (NORMALIZED)
0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (
°
C)
I
– 60
Figure 5. Collector–Emitter Voltage versus
Ambient Temperature
NORMALIZED TO TA = 25
°
C
0.7
TA, AMBIENT TEMPERATURE (
°
C)
VCE, COLLECTOR–EMITTER VOLTAGE (NORMALIZED)
– 40 – 20 0 20 40 60 80 100
0.8
0.9
1
1.1
1.2
1.3
0
Figure 6. Collector–Emitter Dark Current versus
Ambient Temperature
1
TA, AMBIENT TEMPERATURE (
°
C)
I
10
102
103
104
105
20 40 60 80 100
CEO, COLLECTOR–EMITTER DARK CURRENT
0.1
Figure 7. Turn–On Switching Times
(Typical Value)
1
IF, LED INPUT CURRENT (mA)
t, TIME ( s)
10
100
1000
µ
0.2 0.5 1 2 5 10 20 50 100
100
10
0.1
1
IF, LED INPUT CURRENT (mA)
10
100
1000
0.2 0.5 1 2 5 10 20 50 100
10
t, TIME ( s)
µ
Figure 8. Turn–Off Switching Times
(Typical Value)
(NORMALIZED)
10 V
NORMALIZED TO:
VCE = 10 V
TA = 25
°
C
VCE = 30 V
RL = 1000 100
RL = 1000
NORMALIZED TO TA = 25
°
C
VCC = 10 V
VCC = 10 V
 
4 Motorola Optoelectronics Device Data
TEST CIRCUIT
VCC = 10 V
IF = 5 mA
INPUT
RL = 100
Ω
OUTPUT
WAVEFORMS
10%
90%
ton
INPUT PULSE
OUTPUT PULSE
tf
toff
tr
Figure 9. Switching Time Test Circuit and Waveforms
 
5
Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS
CASE 730A–04
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
6 4
1 3
–A–
–B–
SEATING
PLANE
–T–
4 PLF
K
C
N
G
6 PLD
6 PLE
M
A
M
0.13 (0.005) B M
T
L
M
6 PLJ
M
B
M
0.13 (0.005) A M
T
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.320 0.350 8.13 8.89
B0.240 0.260 6.10 6.60
C0.115 0.200 2.93 5.08
D0.016 0.020 0.41 0.50
E0.040 0.070 1.02 1.77
F0.010 0.014 0.25 0.36
G0.100 BSC 2.54 BSC
J0.008 0.012 0.21 0.30
K0.100 0.150 2.54 3.81
L0.300 BSC 7.62 BSC
M0 15 0 15
N0.015 0.100 0.38 2.54
_ _ _ _
STYLE 3:
PIN 1. ANODE
2. CATHODE
3. NC
4. EMITTER
5. COLLECTOR
6. NC
CASE 730C–04
ISSUE D
–A–
–B–
S
SEATING
PLANE
–T–
J
K
L
6 PL
M
B
M
0.13 (0.005) A M
T
C
D6 PL
M
A
M
0.13 (0.005) B M
T
H
G
E6 PL
F4 PL
31
46
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.320 0.350 8.13 8.89
B0.240 0.260 6.10 6.60
C0.115 0.200 2.93 5.08
D0.016 0.020 0.41 0.50
E0.040 0.070 1.02 1.77
F0.010 0.014 0.25 0.36
G0.100 BSC 2.54 BSC
H0.020 0.025 0.51 0.63
J0.008 0.012 0.20 0.30
K0.006 0.035 0.16 0.88
L0.320 BSC 8.13 BSC
S0.332 0.390 8.43 9.90
*Consult factory for leadform
option availability
 
6 Motorola Optoelectronics Device Data
*Consult factory for leadform
option availability
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
CASE 730D–05
ISSUE D
6 4
1 3
–A–
–B–
N
C
K
G
F4 PL
SEATING
D6 PL
E6 PL
PLANE
–T–
M
A
M
0.13 (0.005) B M
T
L
J
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.320 0.350 8.13 8.89
B0.240 0.260 6.10 6.60
C0.115 0.200 2.93 5.08
D0.016 0.020 0.41 0.50
E0.040 0.070 1.02 1.77
F0.010 0.014 0.25 0.36
G0.100 BSC 2.54 BSC
J0.008 0.012 0.21 0.30
K0.100 0.150 2.54 3.81
L0.400 0.425 10.16 10.80
N0.015 0.040 0.38 1.02
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “T ypicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer .
How to reach us:
USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com – T OUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MOC8020/D
*MOC8020/D*
◊