EC40A 40mm Size Ring Type Less shaft wobble achieves good operation feel Typical Specifications Items Specifications 0.5mA 5V DC Operating life 30,000 cycles Operating temperature range Encoders Rating -40 to 85 Product Line Number of detent Number of pulse Minimum order unitpcs. Japan Export 200 400 Product No. EC40A1520403 2011 30 15 Insulated Shaft 22 Metal Shaft Detent torque mNm Actuator length mm EC40A1520405 4016 Packing Specifications Number of packagespcs. 1 case /Japan 1 case /export packing Export package measurements mm 200 400 540x360x380 Through Shaft Type Tray Ring Type Dimensions Unit:mm PC board mounting hole dimensions (Viewed from mounting side) Style (22) o25 o4 9 7.6 0$ 2- 3-7 3- 0. 3. .1 o31.4 (3-R3 .4 4-3 0$ 2.1 2-2 ACB 4 3o1 2.5 ho 2.5 le 3-3.5 22 A CB le le 0.2 2-4 2 2-4 2.1 2-2 ho ho 1.8 3 5 21.4 ) o29.4 3-1.5 22.8 4 11 42.3 33.4 0 3 $ 30$ 11 o2 3.1 8.5 22.8 3-6 3.5 6-3.7 19.5 20.2 2.5 3-o2.6 hole 2-24 Mounting surface 12 Sliding Noise V1=V2=2.5V max. A signal B signal OFF OFF ON ON Detent stability position CW direction Test circuit R Output waveform 5V DC t R Terminal A Terminal B t V1 5V Output Wave V2 Encoder Terminal C Measurement conditionRotation speed 360/s ON OFF ON Sliding direction t : Masking time to avoid chattering At R = 10k Chattering : 3ms max. Bounce : 2ms max. Refer to P.299 for soldering conditions. 295 Encoders List of Varieties Ring type Type Series 40mm size 45mm size 50mm size 60mm size EC40A EC45A EC50A EC60B Incremental Two phase A and B Absolute type Photo Encoders Output Shaft types Ring type Number of pulse / Number of detent Metal Shaft Dimensions mm Incremental Two phase A and B 15/30 31 positions 9/18 15/30 W 40.4 44.5 50.8 62.4 D 43 45 50 60 6.5 7.5 H 9 Insulated Shaft Operating temperature range -40 to 85 Operating life 30,000 cycles Automotive use 40,000 cycles Through Shaft Type Ring Type 1mA 5V DC 10mA 5V DC -- -- 10M min. 250V DC 100M min. 250V DC Life cycle (availability) Rating Max./min. operating Electrical currentResistive load performance Insulation resistance Mechanical performance 0.5mA 5V DC -- -- 10M min. 50V DC Voltage proof 50V AC for 1 minute Detent torque 2011mNm 4016mNm Push-pull strength 50V AC for 1 minute or 60V AC for 2s 3616mNm Push 300V AC for 1 minute or 360V AC for 1s 4014mNm 4010mNm 100N Pull 50N 100N Shaft configuration Ring type Terminal type Insertion Switch type -- -- -- -- Contact arrangement -- -- -- -- Travelmm -- -- -- -- Operating forceN -- -- -- -- -- -- -- -- Rotational torque -- -- -- -- Rating -- -- -- -- Contact resistance -- -- -- -- Operating life -- -- -- -- 295 296 297 298 Switch Specifications Switch ON position Page Encoders Soldering Conditions 299 Encoders Cautions 300 Note Indicates applicability to all products in the series. 258 Encoders / Soldering Conditions Reference for Manual Soldering Tip temperature Soldering time No. of solders EC05E, EC09E, EC10E, EC111, EC11B, EC11E, EC11G, EC11K, EC11M, EC11N, EC12D, EC12E, EC18A, EC21A, EC28A, EC35A, EC35AH, EC40A, EC45A, EC50A, EC60B, EM11B, EC21C, EC28C, EC35CH 350 max. 3s max. 1 time EC11J 35010 3 1 s 0 2 times Encoders Series Reference for Dip Soldering Dip soldering No. of solders Soldering temperature Soldering time EC09E, EC11B, EC111, EC11E, EC11G, EC11K, EC11M, EC11N, EC18A, EC21A, EC28A, EC35A, EC35AH, EC50A, EC60B 100 max. 2 min. max. 2605 51s 2 times max. EM11B 100 max. 1 min. max. 260 max. 3s max. 2 times max. EC10E, EC12D, EC12E 100 max. 1 min. max. 2605 31s 2 times max. EC40A 110 max. 1 min. max. 260 max. 10s max. 1 time EC45A 100 max. 2 min. max. 260 max. 5s max. 2 times max. Ring Type Example of Reflow Soldering Condition Temperature profile 300 Temperature (C ) Through Shaft Type Heating time Insulated Shaft Soldering surfacetemperature Metal Shaft Preheating Series A B 200 C D 100 Room temperature Time (s) Pre-heating E max. F max. G max. H max. Series A B C D E F G H No. of reflows EC11J 260 230 180 150 2 min. max. 3s 40s 4 min. max. 2 times max. EC05E 250 min. 230 min. 180 150 60s to 120s 30s to 40s 2 times max. EC21C 230 to 245 220 200 150 60s to 120s 25s to 60s 300s max. 1 time max. 260 230 180 150 2 min. min. 3s 40s 230s max. 1 time max. EC28C, EC35CH Notes 1. When using an infrared reflow oven, solder may sometimes not be applied. Be sure to use a hot air reflow oven or a type that uses infrared rays in combination with hot air. 2. The temperatures given above are the maximum temperatures at the terminals of the encoder when employing a hot air reflow method. The temperature of the PC board and the surface temperature of the encoder may vary greatly depending on the PC board material, its size and thickness. Ensure that the surface temperature of the encoder does not rise to 250 or greater. 3. Conditions vary to some extent depending on the type of reflow bath used. Be sure to give due consideration to this prior to use. 299