VRE410 Precision Dual Reference THALER CORPORATION * 2015 N. FORBES BOULEVARD * TUCSON, AZ. 85745 * (520) 882-4000 FEATURES PIN CONFIGURATION * 10.000 V OUTPUT 1.000 mV (.01%) * TEMPERATURE DRIFT: 0.6 ppm/C N/C 1 - VOUT 2 14 N/C 13 +VOUT 3 VRE410 12 N/C - VIN 4 TOP VIEW 11 +VIN N/C 5 10 N/C REF. GND 6 9 N/C GND 7 8 N/C * LOW NOISE: 6 Vpp (0.1-10Hz) N/C * TRACKING ERROR: 0.5 mV max. * EXCELLENT LINE REGULATION: 6ppm/V Typ. * SURFACE MOUNT AND DIP PACKAGES FIGURE 1 DESCRIPTION The VRE410 is a low cost, high precision, 10.0V reference. Packaged in 14 pin DIP or SMT packages, the device is ideal for new designs that need a high performance reference. The device provides ultrastable 10.000V output with 1.000 mV (.01%) initial accuracy and a temperature coefficient of 0.6 ppm/C. This improvement in accuracy is made possible by a unique, patented multipoint laser compensation technique developed by Thaler Corporation. Another key feature of this reference is the 0.5 mV maximum tracking error between the positive and negative output voltages over the full operating temperature range. This is extremely important in high performance systems for reducing overall system errors. For designs which use the DIP package in a socket, there is a reference ground pin to eliminate reference ground errors. The VRE410 is recommended for use as a reference for high precision D/A and A/D converters which require an external precision reference. The device is also ideal for calibrating scale factor on high resolution A/D converters. The VRE410 offers superior performance over monolithic references. SELECTION GUIDE Model Initial Error mV Temp. Coeff. ppm/C Temp. Range C VRE410A VRE410B VRE410C VRE410J VRE410K VRE410L 1.0 1.6 2.0 1.0 1.6 2.0 0.6 1.0 2.0 0.6 1.0 2.0 0C to +70C 0C to +70C 0C to +70C -40C to +85C -40C to +85C -40C to +85C For package option add D for DIP or S for Surface Mount to end of model number. VRE410DS REV. A MAY 1996 ELECTRICAL SPECIFICATIONS VRE410 Vps = 15V, T = 25C, RL = 10K unless otherwise noted. MODEL A/J PARAMETER MIN TYP B/K MAX C/L MIN TYP MAX MIN TYP MAX UNITS * * * * * * * * * * * * * * * * * * V C C C ABSOLUTE RATINGS Power Supply 13.5 15 22 Operating Temp. (A,B,C ) 0 +70 Operating Temp. (J,K,L) -40 +85 Storage Temperature -65 +150 Short Circuit Protection Continuous * * * * OUTPUT VOLTAGE VRE410 10.00 V OUTPUT VOLTAGE ERRORS Initial Error (1) Warmup Drift Tmin - Tmax (2) (3) Tracking Error Long-Term Stability Noise (.1-10Hz) 1.00 1.60 1 2.00 2 0.6 0.5 3 1.0 0.7 6 6 2.0 1.0 * * * * mV ppm ppm/ C mV ppm/1000hrs Vpp OUTPUT CURRENT Range 10 * * mA REGULATION Line Load POWER SUPPLY CURRENTS 10 * * * * * * ppm/V ppm/mA 7 4 9 6 * * * * * * * * mA mA (4) +PS -PS NOTES: 3 3 *Same as A/J Models. 1. The specified values are without external trim. 4. The specified values are unloaded. 2. The temperature coefficient (tc) is determined by the box method using the following formula: Vmax - Vmin x 106 tc = Vnominal x (Tmax-Tmin) 3. The tracking error is the deviation between the positive and negative output over the operating temp. range. VRE410DS REV. A MAY 1996 TYPICAL PERFORMANCE CURVES VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE Temperature oC VRE410A Temperature oC VRE410B Temperature oC VRE410C VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE Temperature oC VRE410J Temperature oC VRE410K Temperature oC VRE410L POSITIVE OUTPUT (TYP) QUIESCENT CURRENT VS. TEMP Temperature oC JUNCTION TEMP. RISE VS. OUTPUT CURRENT Output Current (mA) PSRR VS. FREQUENCY Frequency (Hz) NEGATIVE OUTPUT (TYP) QUIESCENT CURRENT VS. TEMP Temperature oC JUNCTION TEMP. RISE VS. OUTPUT CURRENT Output Current (mA) PSRR VS. FREQUENCY Frequency (Hz) VRE410DS REV. A MAY 1996 DISCUSSION OF PERFORMANCE THEORY OF OPERATION The following discussion refers to the schematic below. In operation, approximately 6.3 volts is applied to the noninverting input of the op amp. The voltage is amplified by the op amp to produce a 10.000V output. The gain is determined by the networks R1 and R2: G=1 + R2/R1. The 6.3V zener diode is used because it is the most stable diode over time and temperature. The zener operating current is derived from the regulated output voltage through R3. This feedback arrangement provides a closely regulated zener current. This current determines the slope of the references' voltage vs. temperature function. By trimming the zener current a lower drift over temperature can be achieved. But since the voltage vs. temperature function is nonlinear this compensation technique is not well suited for wide temperature ranges. Thaler Corporation has developed a nonlinear compensation network of thermistors and resistors that is used in the VRE series voltage references. This proprietary network eliminates most of the nonlinearity in the voltage vs. temperature function. By then adjusting the slope, Thaler Corporation produces a very stable voltage over wide temperature ranges. The VRE400 series voltage references have the ground terminal brought out on two pins (pin 6 and 7) which are connected together internally. This allows the user to achieve greater accuracy when using a socket. Voltage references have a voltage drop across their power supply ground pin due to quiescent current flowing through the contact resistance. If the contact resistance was constant with time and temperature, this voltage drop could be trimmed out. When the reference is plugged into a socket, this source of error can be as high as 20ppm. By connecting pin 7 to the power supply ground and pin 6 to a high impedance ground point in the measurement circuit, the error due to the contact resistance can be eliminated. If the unit is soldered into place the contact resistance is sufficiently small that it doesn't effect performance. VRE410 FIGURE 2 VRE410DS REV. A MAY 1996 MECHANICAL FIGURE 3 INCHES MILLIMETER INCHES MILLIMETER DIM MIN MAX MIN MAX DIM MIN MAX MIN MAX A .114 .136 2.90 3.45 E .495 .526 12.5 13.3 B .098 .103 2.48 2.62 E1 .390 .415 9.91 10.5 B1 .047 .056 1.19 1.42 E2 .265 .270 6.73 6.86 C .103 .118 2.62 3.00 P .090 .110 2.29 2.79 C1 .009 .020 0.22 0.51 Q .024 .035 0.61 .890 C2 .054 .062 1.37 1.57 S .040 .060 1.02 1.52 D .690 .715 17.5 18.1 D1 .666 .680 16.9 17.2 FIGURE 4 INCHES MILLIMETER INCHES MILLIMETER DIM MIN MAX MIN MAX DIM MIN MAX MIN MAX A .114 .136 2.90 3.45 E .410 .435 10.4 11.0 B .018 .027 .460 .690 E1 .390 .415 9.91 10.5 B1 .047 .056 1.19 1.42 E2 .265 .270 6.73 6.86 B2 .097 .103 2.46 2.62 G1 .285 .315 7.24 8.00 C .009 .020 0.22 0.51 L .195 .225 4.95 5.72 D .690 .715 17.5 18.1 P .090 .110 2.29 2.79 D1 .666 .680 16.9 17.2 Q .050 .070 1.27 1.79 S .040 .060 1.02 1.52 VRE410DS REV. A MAY 1996