GaAs INTEGRATED CIRCUIT PG2214TK T 1 4M 6 L, S-BAND SPDT SWITCH DESCRIPTION The PG2214TK is a GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which was developed 22 * Switch control voltage ce m * APPLICATIONS pla * : Vcont (H) = 1.8 to 5.3 V (3.0 V TYP.) : Vcont (L) = 0.2 to +0.2 V (0 V TYP.) Low insertion loss : Lins1 = 0.25 dB TYP. @ f = 0.05 to 0.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.25 dB TYP. @ f = 0.5 to 1.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins3 = 0.30 dB TYP. @ f = 1.0 to 2.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins4 = 0.35 dB TYP. @ f = 2.0 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins5 = 0.35 dB TYP. @ f = 2.5 to 3.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V High isolation : ISL1 = 32 dB TYP. @ f = 0.05 to 0.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 28 dB TYP. @ f = 0.5 to 1.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL3 = 27 dB TYP. @ f = 1.0 to 2.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL4 = 26 dB TYP. @ f = 2.0 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL5 = 24 dB TYP. @ f = 2.5 to 3.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V Handling power : Pin (1 dB) = +27.0 dBm TYP. @ f = 0.5 to 3.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +20.0 dBm TYP. @ f = 0.5 to 3.0 GHz, Vcont (H) = 1.8 V, Vcont (L) = 0 V High-density surface mounting : 6-pin lead-less minimold package (1.5 1.1 0.55 mm) A Re S * CG FEATURES * Een O t: U for mobile phone and another L, S-band application. This device can operate 2 control switching by control voltage 1.8 to 5.3 V. This device can operate frequency from 0.05 to 3.0 GHz, having the low insertion loss and high isolation. This device is housed in a 6-pin lead-less minimold (1511) package. And this package is able to high-density surface mounting. PH * L, S-band digital cellular or cordless telephone * W-LAN, WLL and BluetoothTM etc. ORDERING INFORMATION Part Number Marking -In 6-pin lead-less minimold (1511) G4K Supplying Form Embossed tape 8 mm wide Pin 1, 6 face the perforation side of the tape Qty 5 kpcs/reel Dr op PG2214TK-E2 Package Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2214TK-A Caution: Observe precautions when handling because these devices are sensitive to electrostatic discharge Document No. PG10475EJ04V0DS (4th edition) Date Published October 2004 CP(K) The mark shows major revised points. PG2214TK PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM Pin Name 1 OUTPUT1 2 T 1 Low High High Low INPUTOUTPUT1 INPUTOUTPUT2 ON OFF OFF ON Vcont2 5 INPUT 6 Vcont1 22 Vcont2 ABSOLUTE MAXIMUM RATINGS (T A = +25C, unless otherwise specified) Parameter Switch Control Voltage Input Power Symbol Ratings Vcont Note V +30 dBm TA 45 to +85 C 55 to +150 C Tstg Note Vcont1 Vcont2 6.0 V ce m Storage Temperature Unit Pin A Re S Operating Ambient Temperature +6.0 PH Switch Control Voltage (H) Symbol MIN. TYP. MAX. Unit Vcont (H) 1.8 3.0 5.3 V Vcont (L) 0.2 0 0.2 V Dr op -In Switch Control Voltage (L) pla RECOMMENDED OPERATING RANGE (T A = +25C, unless otherwise specified) Parameter 2 Data Sheet PG10475EJ04V0DS OUTPUT2 4 CG Vcont1 Een O t: U TRUTH TABLE GND 4M 3 6 Pin No. PG2214TK ELECTRICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, DC cut capacitors = 100 pF, unless otherwise specified) Symbol Test Conditions Note 1 MIN. TYP. MAX. Unit 0.25 0.45 dB 0.45 Lins1 f = 0.05 to 0.5 GHz Insertion Loss 2 Lins2 f = 0.5 to 1.0 GHz 0.25 Insertion Loss 3 Lins3 f = 1.0 to 2.0 GHz Insertion Loss 4 Lins4 f = 2.0 to 2.5 GHz Insertion Loss 5 Lins5 f = 2.5 to 3.0 GHz Isolation 4 Isolation 5 Input Return Loss 1 Input Return Loss 2 Output Return Loss 1 Output Return Loss 2 0.1 dB Loss Compression Input Power Note 2 1 dB Loss Compression T 1 f = 0.05 to 0.5 GHz ISL2 f = 0.5 to 1.0 GHz ISL3 f = 1.0 to 2.0 GHz ISL4 f = 2.0 to 2.5 GHz ISL5 f = 2.5 to 3.0 GHz Intermodulation Intercept Point 0.60 dB 32 dB 28 dB dB 21 24 dB 15 20 dB 15 20 dB 15 20 dB 15 20 dB +21.0 +23.0 dBm f = 0.5 to 3.0 GHz +23.0 dBm f = 0.5 to 3.0 GHz +27.0 dBm f = 2.0 GHz, Pin = +15 dBm 55 47 dBc f = 2.5 GHz, Pin = +15 dBm 55 47 dBc f = 2.0 GHz, Pin = +15 dBm 55 47 dBc f = 2.5 GHz, Pin = +15 dBm 55 47 dBc +58 dBm 4 20 A 20 200 ns RLout1 f = 0.05 to 0.5 GHz RLout2 f = 0.5 to 3.0 GHz IIP3 0.35 26 f = 0.5 to 3.0 GHz 3f0 dB 23 Note 1 Note 1 f = 2.0/2.5 GHz pla 3rd Harmonics 0.55 dB RLin2 2f0 0.35 ce m 2nd Harmonics dB 27 f = 0.05 to 0.5 GHz Pin (1 dB) 25 0.50 24 RLin1 Pin (0.1 dB) 29 A Re S Input Power Note 3 ISL1 dB 0.30 22 Isolation 3 Note 1 CG Isolation 2 Een O t: U Isolation 1 6 Insertion Loss 1 4M Parameter f = 0.5 to 3.0 GHz, 2 tone, Pin = +16 dBm, 5 MHz spicing PH Switch Control Current Switch Control Speed Icont tSW 50% CTL to 90/10% RF Notes 1. DC cut capacitors = 1 000 pF at f = 0.05 to 0.5 GHz -In 2. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. 3. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of Dr op linear range. Data Sheet PG10475EJ04V0DS 3 PG2214TK ELECTRICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 1.8 V, Vcont (L) = 0 V, DC cut capacitors = 100 pF, unless otherwise specified) Symbol Test Conditions Note 1 MIN. TYP. MAX. Unit 0.25 0.50 dB 0.50 Lins6 f = 0.05 to 0.5 GHz Insertion Loss 7 Lins7 f = 0.5 to 1.0 GHz 0.25 Insertion Loss 8 Lins8 f = 1.0 to 2.0 GHz Insertion Loss 9 Lins9 f = 2.0 to 2.5 GHz Insertion Loss 10 Lins10 f = 2.5 to 3.0 GHz Isolation 9 Input Return Loss 3 Output Return Loss 3 0.1 dB Loss Compression Input Power Note 2 T 1 f = 0.05 to 0.5 GHz ISL7 f = 0.5 to 2.0 GHz ISL8 f = 2.0 to 2.5 GHz ISL9 f = 2.5 to 3.0 GHz RLin3 RLout3 Pin (0.1 dB) Note 3 Switch Control Current f = 0.05 to 3.0 GHz Note 1 f = 0.05 to 3.0 GHz Note 1 f = 2.0/2.5 GHz f = 0.5 to 3.0 GHz Icont tSW 50% CTL to 90/10% RF 0.55 dB 0.35 0.60 dB 0.35 0.65 dB 30 dB 27 dB 21 25 dB 20 24 dB 15 20 dB 15 20 dB +14.0 +17.0 dBm +17.0 dBm +20.0 dBm 4 20 A 20 200 ns ce m A Re S Switch Control Speed Pin (1 dB) 27 23 f = 0.5 to 3.0 GHz 1 dB Loss Compression Input Power ISL6 dB 0.30 22 Isolation 8 Note 1 CG Isolation 7 Een O t: U Isolation 6 6 Insertion Loss 6 4M Parameter Notes 1. DC cut capacitors = 1 000 pF at f = 0.05 to 0.5 GHz 2. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. 3. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of pla linear range. Caution This device is used it is necessary to use DC cut capacitors. PH The value of DC cut capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of Dr op -In recommended DC cut capacitor value is less than 100 pF. 4 Data Sheet PG10475EJ04V0DS PG2214TK CG 22 Een O t: U T 1 4M 6 EVALUATION CIRCUIT Note C0 : 0.05 to 0.5 GHz 1 000 pF : 0.5 to 3.0 GHz 100 pF pla Dr op -In PH ce m A Re S The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. Data Sheet PG10475EJ04V0DS 5 PG2214TK pla ce m A Re S CG 22 Een O t: U T 1 4M 6 ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD PH USING THE EVALUATION BOARD Symbol C1, C2, C3 100 pF 1 000 pF Dr op -In C4, C5 Values 6 Data Sheet PG10475EJ04V0DS PG2214TK Remark The graphs indicate nominal characteristics. CG 22 Een O t: U T 1 4M 6 TYPICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, DC cut capacitors = 100 pF, unless otherwise specified) pla Dr op -In PH ce m A Re S Caution These characteristics values include the losses of the evaluation board. Data Sheet PG10475EJ04V0DS 7 pla Dr op -In PH ce m A Re S CG 22 Een O t: U T 1 4M 6 PG2214TK Remark The graphs indicate nominal characteristics. 8 Data Sheet PG10475EJ04V0DS 22 Een O t: U T 1 4M 6 PG2214TK pla Dr op -In PH ce m A Re S CG Remark The graph indicate nominal characteristics. Data Sheet PG10475EJ04V0DS 9 PG2214TK PACKAGE DIMENSIONS pla Dr op -In PH ce m A Re S CG 22 Een O t: U T 1 4M 6 6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm) 10 Data Sheet PG10475EJ04V0DS PG2214TK RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. : 260C or below Time at peak temperature : 10 seconds or less Maximum number of reflow processes : 12030 seconds : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (package surface temperature) : 215C or below Time at temperature of 200C or higher : 25 to 40 seconds : 30 to 60 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (molten solder temperature) : 260C or below WS260 : 10 seconds or less Preheating temperature (package surface temperature) : 120C or below Maximum number of flow processes : 1 time Maximum chlorine content of rosin flux (% mass) VP215 22 Preheating time at 120 to 150C Time at peak temperature Partial Heating : 60 seconds or less Een O t: U Wave Soldering T 1 Preheating time at 120 to 180C IR260 4M Peak temperature (package surface temperature) Time at temperature of 220C or higher VPS Condition Symbol CG Infrared Reflow Soldering Conditions 6 Soldering Method : 0.2%(Wt.) or below Peak temperature (pin temperature) : 350C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below HS350 pla Dr op -In PH ce m A Re S Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10475EJ04V0DS 11 PG2214TK Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. T 1 4M 6 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. pla Dr op -In PH ce m A Re S CG 22 Een O t: U * Do not lick the product or in any way allow it to enter the mouth. 12 Data Sheet PG10475EJ04V0DS NOTICE Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by California Eastern Laboratories or Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by California Eastern Laboratories, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. Please contact a California Eastern Laboratories sales office for details as to environmental matters such as the environmental compatibility of each Renesas 8. Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories. 12. Please contact a California Eastern Laboratories sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. pla ce m PH A Re S CG 22 Een O t: U T 1 4M 6 1. -I n NOTE 1: "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. NOTE 2: "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. NOTE 3: Products and product information are subject to change without notice. Dr op CEL Headquarters * 4590 Patrick Henry Drive, Santa Clara, CA 95054 * Phone (408) 919-2500 * www.cel.com For a complete list of sales offices, representatives and distributors, Please visit our website: www.cel.com/contactus Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: CEL: UPG2214TK-A UPG2214TK-E2-A UPG2214TK-EVAL-A