LM555/LM555C Timer General Description Features The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty cycle are accurately controlled with two external resistors and one capacitor. The circuit may be triggered and reset on falling waveforms, and the output circuit can source or sink up to 200 mA or drive TTL circuits. n n n n n n n n n Direct replacement for SE555/NE555 Timing from microseconds through hours Operates in both astable and monostable modes Adjustable duty cycle Output can source or sink 200 mA Output and supply TTL compatible Temperature stability better than 0.005% per C Normally on and normally off output Available in 8 pin MSOP package n n n n n n n Precision timing Pulse generation Sequential timing Time delay generation Pulse width modulation Pulse position modulation Linear ramp generator Applications Schematic Diagram DS007851-1 (c) 1997 National Semiconductor Corporation DS007851 www.national.com LM555/LM555C Timer May 1997 Absolute Maximum Ratings (Note 2) Storage Temperature Range -65C to +150C Soldering Information Dual-In-Line Package Soldering (10 Seconds) 260C Small Outline Packages (SOIC and MSOP) Vapor Phase (60 Seconds) 215C Infrared (15 Seconds) 220C See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Power Dissipation (Note 3) LM555H, LM555CH LM555, LM555CN LM555CMM Operating Temperature Ranges LM555C LM555 +18V 760 mW 1180 mW 613 mW 0C to +70C -55C to + 125C Electrical Characteristics (Notes 1, 2) (TA = 25C, VCC = +5V to +15V, unless othewise specified) Limits Parameter Conditions LM555 Min Supply Voltage Supply Current Typ 4.5 VCC = 5V, RL = VCC = 15V, RL = LM555C Max Min 18 4.5 Typ Units Max 16 V 3 5 3 6 mA 10 12 10 15 mA (Low State) (Note 4) Timing Error, Monostable 0.5 1 % 30 50 ppm/C Accuracy over Temperature 1.5 1.5 % Drift with Supply 0.05 0.1 %/V 1.5 2.25 % 90 150 ppm/C Initial Accuracy Drift with Temperature RA = 1k to 100 k, C = 0.1 F, (Note 5) Timing Error, Astable Initial Accuracy Drift with Temperature RA, RB = 1k to 100 k, C = 0.1 F, (Note 5) Accuracy over Temperature 2.5 3.0 % Drift with Supply 0.15 0.30 %/V Threshold Voltage Trigger Voltage 0.667 VCC = 15V VCC = 5V 0.667 x VCC 4.8 5 5.2 5 V 1.45 1.67 1.9 1.67 0.01 0.5 0.5 Trigger Current Reset Voltage 0.4 Reset Current Threshold Current Control Voltage Level 0.5 1 0.1 0.4 0.4 V 0.9 A 0.5 1 V 0.1 0.4 mA (Note 6) VCC = 15V 0.1 0.25 0.1 0.25 A 9.6 10 10.4 9 10 11 V VCC = 5V 2.9 3.33 3.8 2.6 3.33 4 V 1 100 1 100 nA Pin 7 Leakage Output High Pin 7 Sat (Note 7) Output Low Output Low www.national.com VCC = 15V, I7 = 15 mA VCC = 4.5V, I7 = 4.5 mA 150 70 2 180 100 80 mV 200 mV Electrical Characteristics (Notes 1, 2) (Continued) (TA = 25C, VCC = +5V to +15V, unless othewise specified) Limits Parameter Conditions LM555 Min Output Voltage Drop (Low) Output Voltage Drop (High) LM555C Max VCC = 15V ISINK = 10 mA ISINK = 50 mA 0.1 0.15 0.1 0.25 V 0.4 0.5 0.4 0.75 V ISINK = 100 mA ISINK = 200 mA VCC = 5V 2 2.2 2 2.5 V 2.5 ISINK = 8 mA ISINK = 5 mA ISOURCE = 200 mA, VCC = 15V ISOURCE = 100 mA, VCC = 15V VCC = 5V 0.1 Min Typ Units Typ Max 2.5 V 0.25 V 0.25 12.5 0.35 V 12.5 V V 13 13.3 12.75 13.3 3 3.3 2.75 3.3 V Rise Time of Output 100 100 ns Fall Time of Output 100 100 ns Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: For operating at elevated temperatures the device must be derated above 25C based on a +150C maximum junction temperature and a thermal resistance of 164C/W (T0-5), 106C/W (DIP), 170C/W (S0-8), and 204C/W (MSOP) junction to ambient. Note 4: Supply current when output high typically 1 mA less at VCC = 5V. Note 5: Tested at VCC = 5V and VCC = 15V. Note 6: This will determine the maximum value of RA + RB for 15V operation. The maximum total (RA + RB) is 20 M. Note 7: No protection against excessive pin 7 current is necessary providing the package dissipation rating will not be exceeded. Note 8: Refer to RETS555X drawing of military LM555H and LM555J versions for specifications. Connection Diagrams Metal Can Package Dual-In-Line, Small Outline and Molded Mini Small Outline Packages DS007851-2 Top View Order Number LM555H or LM555CH See NS Package Number H08C DS007851-3 Top View Order Number LM555J, LM555CJ, LM555CM, LM555CMM or LM555CN See NS Package Number J08A, M08A, MUA08A or N08E 3 www.national.com Typical Performance Characteristics Minimuim Pulse Width Required for Triggering Supply Current vs Supply Voltage DS007851-19 DS007851-4 Low Output Voltage vs Output Sink Current Low Output Voltage vs Output Sink Current DS007851-21 Output Propagation Delay vs Voltage Level of Trigger Pulse Output Propagation Delay vs Voltage Level of Trigger Pulse DS007851-25 4 DS007851-20 Low Output Voltage vs Output Sink Current DS007851-22 DS007851-24 www.national.com High Output Voltage vs Output Source Current DS007851-23 Discharge Transistor (Pin 7) Voltage vs Sink Current DS007851-26 Typical Performance Characteristics (Continued) Discharge Transistor (Pin 7) Voltage vs Sink Current DS007851-27 Applications Information MONOSTABLE OPERATION In this mode of operation, the timer functions as a one-shot (Figure 1). The external capacitor is initially held discharged by a transistor inside the timer. Upon application of a negative trigger pulse of less than 1/3 VCC to pin 2, the flip-flop is set which both releases the short circuit across the capacitor and drives the output high. DS007851-6 VCC = 5V TIME = 0.1 ms/DIV. RA = 9.1 k C = 0.01 F Top Trace: Input 5V/Div. Middle Trace: Output 5V/Div. Bottom Trace: Capacitor Voltage 2V/Div. FIGURE 2. Monostable Waveforms During the timing cycle when the output is high, the further application of a trigger pulse will not effect the circuit so long as the trigger input is returned high at least 10 s before the end of the timing interval. However the circuit can be reset during this time by the application of a negative pulse to the reset terminal (pin 4). The output will then remain in the low state until a trigger pulse is again applied. When the reset function is not in use, it is recommended that it be connected to VCC to avoid any possibility of false triggering. DS007851-5 FIGURE 1. Monostable The voltage across the capacitor then increases exponentially for a period of t = 1.1 RA C, at the end of which time the voltage equals 2/3 VCC. The comparator then resets the flip-flop which in turn discharges the capacitor and drives the output to its low state. Figure 2 shows the waveforms generated in this mode of operation. Since the charge and the threshold level of the comparator are both directly proportional to supply voltage, the timing internal is independent of supply. Figure 3 is a nomograph for easy determination of R, C values for various time delays. NOTE: In monostable operation, the trigger should be driven high before the end of timing cycle. 5 www.national.com Applications Information (Continued) DS007851-9 VCC = 5V TIME = 20 s/DIV. RA = 3.9 k RB = 3 k C = 0.01 F DS007851-7 Top Trace: Output 5V/Div. Bottom Trace: Capacitor Voltage 1V/Div. FIGURE 5. Astable Waveforms FIGURE 3. Time Delay The charge time (output high) is given by: t1 = 0.693 (RA + RB) C ASTABLE OPERATION If the circuit is connected as shown in Figure 4 (pins 2 and 6 connected) it will trigger itself and free run as a multivibrator. The external capacitor charges through RA + RB and discharges through RB. Thus the duty cycle may be precisely set by the ratio of these two resistors. And the discharge time (output low) by: t2 = 0.693 (RB) C Thus the total period is: T = t1 + t2 = 0.693 (RA +2RB) C The frequency of oscillation is: Figure 6 may be used for quick determination of these RC values. The duty cycle is: DS007851-8 FIGURE 4. Astable In this mode of operation, the capacitor charges and discharges between 1/3 VCC and 2/3 VCC. As in the triggered mode, the charge and discharge times, and therefore the frequency are independent of the supply voltage. Figure 5 shows the waveforms generated in this mode of operation. DS007851-10 FIGURE 6. Free Running Frequency FREQUENCY DIVIDER The monostable circuit of Figure 1 can be used as a frequency divider by adjusting the length of the timing cycle. Figure 7 shows the waveforms generated in a divide by three circuit. www.national.com 6 Applications Information the modulating signal, since the threshold voltage and hence the time delay is varied. Figure 11 shows the waveforms generated for a triangle wave modulation signal. (Continued) DS007851-11 VCC = 5V TIME = 20 s/DIV. RA = 9.1 k C = 0.01 F Top Trace: Input 4V/Div. Middle Trace: Output 2V/Div. Bottom Trace: Capacitor 2V/Div. FIGURE 7. Frequency Divider DS007851-14 PULSE WIDTH MODULATOR FIGURE 10. Pulse Position Modulator When the timer is connected in the monostable mode and triggered with a continuous pulse train, the output pulse width can be modulated by a signal applied to pin 5. Figure 8 shows the circuit, and in Figure 9 are some waveform examples. DS007851-15 VCC = 5V TIME = 0.1 ms/DIV. RA = 3.9 k RB = 3 k C = 0.01 F DS007851-12 Top Trace: Modulation Input 1V/Div. Bottom Trace: Output 2V/Div. FIGURE 11. Pulse Position Modulator FIGURE 8. Pulse Width Modulator LINEAR RAMP When the pullup resistor, RA, in the monostable circuit is replaced by a constant current source, a linear ramp is generated. Figure 12 shows a circuit configuration that will perform this function. DS007851-13 VCC = 5V Top Trace: Modulation 1V/Div. TIME = 0.2 ms/DIV. Bottom Trace: Output Voltage 2V/Div. RA = 9.1 k C = 0.01 F FIGURE 9. Pulse Width Modulator PULSE POSITION MODULATOR This application uses the timer connected for astable operation, as in Figure 10, with a modulating signal again applied to the control voltage terminal. The pulse position varies with DS007851-16 FIGURE 12. 7 www.national.com Applications Information Thus the frequency of oscillation is (Continued) Figure 13 shows waveforms generated by the linear ramp. The time interval is given by: VBE 0.6V DS007851-18 DS007851-17 FIGURE 14. 50% Duty Cycle Oscillator VCC = 5V Top Trace: Input 3V/Div. TIME = 20 s/DIV. Middle Trace: Output 5V/Div. Bottom Trace: Capacitor Voltage 1V/Div. R1 = 47 k R2 = 100 k RE = 2.7 k C = 0.01 F Note that this circuit will not oscillate if RB is greater than 1/2 RA because the junction of RA and RB cannot bring pin 2 down to 1/3 VCC and trigger the lower comparator. ADDITIONAL INFORMATION Adequate power supply bypassing is necessary to protect associated circuitry. Minimum recommended is 0.1 F in parallel with 1 F electrolytic. Lower comparator storage time can be as long as 10 s when pin 2 is driven fully to ground for triggering. This limits the monostable pulse width to 10 s minimum. Delay time reset to output is 0.47 s typical. Minimum reset pulse width must be 0.3 s, typical. Pin 7 current switches within 30 ns of the output (pin 3) voltage. FIGURE 13. Linear Ramp 50% DUTY CYCLE OSCILLATOR For a 50% duty cycle, the resistors RA and RB may be connected as in Figure 14. The time period for the output high is the same as previous, t1 = 0.693 RA C. For the output low it is t2 = www.national.com 8 Physical Dimensions inches (millimeters) Metal Can Package (H) Order Number LM555H or LM555CH NS Package Number H08C Ceramic Dual-In-Line Package (J) Order Number LM555J or LM555CJ NS Package Number J08A 9 www.national.com Physical Dimensions inches (millimeters) (Continued) Small Outline Package (M) Order Number LM555CM NS Package Number M08A www.national.com 10 Physical Dimensions inches (millimeters) (Continued) 8-Lead (0.118" Wide) Molded Mini Small Outline Package Order Number LM555CMM NS Package Number MUA08A 11 www.national.com LM555/LM555C Timer Physical Dimensions inches (millimeters) (Continued) Molded Dual-In-Line Package (N) Order Number LM555CN NS Package Number N08E LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 www.national.com National Semiconductor Europe Fax: (+49) 0-180-530 85 86 Email: cnjwge@tevm2.nsc.com Deutsch Tel: (+49) 0-180-530 85 85 English Tel: (+49) 0-180-532 78 32 Francais Tel: (+49) 0-180-532 93 58 Italiano Tel: (+49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2308 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.