LM94 TruThermTM Hardware Monitor with PI Loop Fan Control for Server Management 1.0 General Description The LM94 hardware monitor has a two wire digital interface compatible with SMBus 2.0. Using a ADC, the LM94 measures the temperature of four remote diode connected transistors as well as its own die and 16 power supply voltages. The LM94 has new TruTherm technology that supports precision thermal diode measurements of processors on sub-micron processes. To set fan speed, the LM94 has two PWM outputs that are each controlled by up to six temperature zones. The fancontrol algorithm can be based on a lookup table, PI (proportional/integral) control loop, or a combination of both. The LM94 includes digital filters that can be invoked to smooth temperature readings for better control of fan speed such that acoustical noise is minimized. The LM94 has four tachometer inputs to measure fan speed. Limit and status registers for all measured values are included. The LM94 builds upon the functionality of previous motherboard server management ASICs, such as the LM93. It also adds measurement and control support for dynamic Vccp monitoring for VRD10/11 and PROCHOT. It is designed to monitor a dual processor Xeon class motherboard with a minimum of external components. 2.0 Features n n n n n n n n n n n n 8-bit ADC Monitors 16 power supplies Monitors 4 remote thermal diodes and 2 LM60 New TruTherm technology support for precision thermal diode measurements Internal ambient temperature sensing Programmable autonomous fan control based on temperature readings with fan boost support Fan boost support on tachometer limit error event Fan control based on 13-step lookup table or PI Control Loop or combination of both PI fan control loop supports Tcontrol Temperature reading digital filters 0.5C digital temperature sensor resolution 0.0625C filtered temperature resolution for fan control n 2 PWM fan speed control outputs n 4 fan tachometer inputs n Dual processor thermal throttling (PROCHOT) monitoring n Dual dynamic VID monitoring (6/7 VIDs per processor) supports VRD10.2/11 n 8 general purpose I/Os: -- 4 can be configured as fan tachometer inputs -- 2 can be configured to connect to processor THERMTRIP -- 2 are standard GPIOs that could be used to monitor IERR signal n 2 general purpose inputs that can be used to monitor the 7th VID signal for VRD11 n Limit register comparisons of all monitored values n 2-wire serial digital interface, SMBus 2.0 compliant -- Supports byte/block read and write -- Selectable slave address (tri-level pin selects 1 of 3 possible addresses) -- ALERT output supports interrupt or comparator modes n 2.5V reference voltage output n 56-pin TSSOP package n XOR-tree test mode 3.0 Key Specifications Voltage Measurement Accuracy Temperature Resolution Temperature Sensor Accuracy Temperature Range: -- LM94 Operational -- Remote Temp Accuracy n Power Supply Voltage n Power Supply Current n n n n 2% FS (max) 9-bits, 0.5C 2.5 C (max) 0C to +85C 0C to +125C +3.0V to +3.6V 1.6 mA 4.0 Applications n Servers n Workstations n Multi-processor based equipment 5.0 Ordering Information Order Number NS Package Number Transport media LM94CIMT MTD56 34 units in rail LM94CIMTX MTD56 1000 units in tape-and-reel I2C is a registered trademark of the Philips Corporation. (c) 2006 National Semiconductor Corporation DS201124 www.national.com LM94 TruThermTM Hardware Monitor with PI Loop Fan Control for Server Management April 2006 LM94 6.0 Block Diagram The block diagram of LM94 hardware is illustrated below. The hardware implementation is a single chip ASIC solution. 20112401 www.national.com 2 LM94 7.0 Application Baseboard management of a dual processor server. Two LM94s may be required to manage a quad processor board. The system diagram below shows a dual processor server 2 Way Xeon Server Management 20112405 3 www.national.com LM94 8.0 Connection Diagram 56 Pin TSSOP 20112402 NS Package MTD56 Top View NS Order Numbers: LM94CIMT (34 units per rail), or LM94CIMTX (1000 units per tape-and-reel) www.national.com 4 LM94 9.0 Pin Descriptions Symbol Pin # Type Function GPIO_0/TACH1 1 Digital I/O (Open-Drain) Can be configured as fan tach input or a general purpose open-drain digital I/O. GPIO_1/TACH2 2 Digital I/O (Open-Drain) Can be configured as fan tach input or a general purpose open-drain digital I/O. GPIO_2/TACH3 3 Digital I/O (Open-Drain) Can be configured as fan tach input or a general purpose open-drain digital I/O. GPIO_3/TACH4 4 Digital I/O (Open-Drain) Can be configured as fan tach input or a general purpose open-drain digital I/O.. GPIO_4 / P1_THERMTRIP 5 Digital I/O (Open-Drain) A general purpose open-drain digital I/O. Can be configured to monitor a CPU's THERMTRIP signal to mask other errors. Supports TTL input logic levels and AGTL compatible input logic levels. GPIO_5 / P2_THERMTRIP 6 Digital I/O (Open-Drain) A general purpose open-drain digital I/O. Can be configured to monitor a CPU's THERMTRIP signal to mask other errors. Supports TTL input logic levels and AGTL compatible input logic levels. GPIO_6 7 Digital I/O (Open-Drain) Can be used to detect the state of CPU1 IERR or a general purpose open-drain digital I/O. Supports TTL input logic levels and AGTL compatible input logic levels. GPIO_7 8 Digital I/O (Open-Drain) Can be used to detect the state of CPU2 IERR or a general purpose open-drain digital I/O. Supports TTL input logic levels and AGTL compatible input logic levels. VRD1_HOT 9 Digital Input CPU1 voltage regulator HOT. Supports TTL input logic levels and AGTL compatible input logic levels. VRD2_HOT 10 Digital Input CPU2 voltage regulator HOT. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID6/GPI8 11 Digital Input CPU2 VID6 input. Could also be used as a general purpose input to trigger an error event. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID6/GPI9 12 Digital Input CPU1 VID6 input. Could also be used as a general purpose input to trigger an error event. Supports TTL input logic levels and AGTL compatible input logic levels. SMBDAT 13 Digital I/O (Open-Drain) Bidirectional System Management Bus Data. Output configured as 5V tolerant open-drain. SMBus 2.0 compliant. SMBCLK 14 Digital Input System Management Bus Clock. Driven by an open-drain output, and is 5V tolerant. SMBus 2.0 Compliant. ALERT/XtestOut 15 Digital Output (Open-Drain) Open-drain ALERT output used in an interrupt driven system to signal that an error event has occurred. Masked error events do not activate the ALERT output. When in XOR tree test mode, functions as XOR Tree output. RESET 16 Digital I/O (Open-Drain) Open-drain reset output when power is first applied to the LM94. Used as a reset for devices powered by 3.3V stand-by. After reset, this pin becomes a reset input. If this pin is not used, connection to an external resistive pull-up is required to prevent LM94 malfunction. AGND 17 GROUND Input Analog Ground. Digital ground and analog ground need to be tied together at the chip then both taken to a low noise system ground. A voltage difference between analog and digital ground may cause erroneous results. VREF 18 Analog Output 2.5V used for external ADC reference, or as a VREF reference voltage 5 www.national.com LM94 9.0 Pin Descriptions (Continued) Symbol Pin # Type Function REMOTE1- 19 Remote Thermal Diode_1- Input (CPU 1 THERMDC) This is the negative input (current sink) from both of the CPU1 thermal diodes. Connected to THERMDC pin of Pentium processor or the emitter of a diode connected MMBT3904 NPN transistor. Serves as the negative input into the A/D for thermal diode voltage measurements. A 100 pF capacitor is optional and can be connected between REMOTE1- and REMOTE1+. REMOTE1a+ 20 Remote Thermal Diode_1+ I/O (CPU1 THERMDA1) This is a positive connection to the first CPU1 thermal diode. Serves as the positive input into the A/D for thermal diode voltage measurements. It also serves as a current source output that forward biases the thermal diode. Connected to THERMDA pin of Pentium processor or the base of a diode connected MMBT3904 NPN transistor. A 100 pF capacitor is optional and can be connected between REMOTE1- and each REMOTE1+. REMOTE2- 21 Remote Thermal Diode_2 - Input (CPU2 THERMDC) This is the negative input (current sink) from both of the CPU2 thermal diodes. Connected to THERMDC pins of Pentium processor or the emitter of a diode connected MMBT3904 NPN transistor. Serves as the negative input into the A/D for thermal diode voltage measurements. A 100 pF capacitor is optional and can be connected between REMOTE2- and each REMOTE2+. REMOTE2a+ 22 Remote Thermal Diode_2 + I/O (CPU2 THERMDA1) This is a positive connection to the first CPU2 thermal diode. Serves as the positive input into the A/D for thermal diode voltage measurements. It also serves as a current source output that forward biases the thermal diode. Connected to THERMDA pin of Pentium processor or the base of a diode connected MMBT3904 NPN transistor. A 100 pF capacitor is optional and can be connected between REMOTE2- and REMOTE2+. AD_IN1/REMOTE1b+ 23 Analog Input (+12V1 or CPU1 THERMDA2) Analog Input for +12V Rail 1 monitoring, for CPU1 voltage regulator. External attenuation resistors required such that 12V is attenuated to 0.927V for nominal 34 scale reading. This pin may also serve as the second positive thermal diode input for CPU1. AD_IN2/REMOTE2b+ 24 Analog Input (+12V2 or CPU2 THERMDA2) Analog Input for +12V Rail 2 monitoring, for CPU2 voltage regulator. External attenuation resistors required such that 12V is attenuated to 0.927V for nominal 34 scale reading. This pin may also serve as the second positive thermal diode input for CPU2. AD_IN3 25 Analog Input (+12V3) Analog Input for +12V Rail 3, for Memory/3GIO slots. External attenuation resistors required such that 12V is attenuated to 0.927V for nominal 34 scale reading. AD_IN4 26 Analog Input (FSB_Vtt) Analog input for 1.2V monitoring, nominal 34 scale reading AD_IN5 27 Analog Input (3GIO / PXH / MCH_Core) Analog input for 1.5V monitoring, nominal 34 scale reading AD_IN6 28 Analog Input (ICH_Core) Analog input for 1.5V monitoring, nominal 34 scale reading AD_IN7 (P1_Vccp) 29 Analog Input (CPU1_Vccp) Analog input for +Vccp (processor voltage) monitoring. AD_IN8 (P2_Vccp) 30 Analog Input (CPU2_Vccp) Analog input for +Vccp (processor voltage) monitoring. AD_IN9 31 Analog Input (+3.3V) Analog input for +3.3V monitoring, nominal 34 scale reading AD_IN10 32 Analog Input (+5V) Analog input for +5V monitoring silver box supply monitoring, nominal 34 scale reading www.national.com 6 LM94 9.0 Pin Descriptions (Continued) Symbol Pin # Type Function AD_IN11 33 Analog Input (SCSI_Core) Analog input for +2.5V monitoring, nominal 34 scale reading. This pin may also be used to monitor an analog temperature sensor such as the LM60, since readings from this input can be routed to the fan control logic. AD_IN12 34 Analog Input (Mem_Core) Analog input for +1.969V monitoring, nominal 34 scale reading. AD_IN13 35 Analog Input (Mem_Vtt) Analog input for +0.984V monitoring, nominal 34 scale reading. AD_IN14 36 Analog Input (Gbit_Core) Analog input for +0.984V S/B monitoring, nominal 34 scale reading. AD_IN15 37 Analog Input (-12V) Analog input for -12V monitoring. External resistors required to scale to positive level. Full scale reading at 1.236V, , nominal 34 scale reading. This pin may also be used to monitor an analog temperature sensor such as the LM60, since readings from this input can be routed to the fan control logic. Address Select 38 3 level analog input This input selects the lower two bits of the LM94 SMBus slave address. 3.3V SB (AD_IN16) 39 POWER (VDD) +3.3V standby power VDD power input for LM94. Generally this is connected to +3.3V standby power. The LM94 can be powered by +3.3V if monitoring in low power states is not required, but power should be applied to this input before any other pins. This pin also serves as the analog input to monitor the 3.3V stand-by (SB) voltage. It is necessary to bypass this pin with a 0.1 F in parallel with 100 pF. A bulk capacitance of 10 F should be in the near vicinity. The 100 pF should be closest to the power pin. GND 40 GROUND Digital Ground. Digital ground and analog ground need to be tied together at the chip then both taken to a low noise system ground. A voltage difference between analog and digital ground may cause erroneous results. PWM1 41 Digital Output (Open-Drain) Fan control output 1. PWM2 42 Digital Output (Open-Drain) Fan control output 2 P1_VID0/P1_VID7 43 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID1 44 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID2 45 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID3 46 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID4 47 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_VID5 48 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P1_PROCHOT 49 Digital I/O (Open-Drain) Connected to CPU1 PROCHOT (processor hot) signal through a bidirectional level shifter. Supports TTL input logic levels and AGTL compatible input logic levels. P2_PROCHOT 50 Digital I/O (Open-Drain) Connected to CPU2 PROCHOT (processor hot) signal through a bidirectional level shifter. Supports TTL input logic levels and AGTL compatible input logic levels. 7 www.national.com LM94 9.0 Pin Descriptions (Continued) Symbol Pin # Type Function P2_VID0/P2_VID7 51 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID1 52 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID2 53 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID3 54 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID4 55 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. P2_VID5 56 Digital Input Voltage Identification signal from the processor. Supports TTL input logic levels and AGTL compatible input logic levels. The over-score indicates the signal is active low ("Not"). 10.0 Recommended Implementation 20112406 Recommended implementation without thermal diode connections www.national.com 8 LM94 10.0 Recommended Implementation (Continued) 20112407 Note: 100 pF cap across each thermal diode is optional and should be placed close to the LM94, if used. The maximum capacitance between thermal diode pins is 300 pF. Thermal diode recommended implementation All but 4 of the analog inputs include internal scaling resistors. External scaling resistors are required for measuring 12V. The inputs are converted to 8-bit digital values such that a nominal voltage appears at 34 scale for positive voltages and 14 scale for negative voltages. The analog inputs are intended to be connected to both baseboard resident VRDs and to standard voltage rails supplied by a SSI compliant power supply. 11.0 Functional Description The LM94 provides 16 channels of voltage monitoring, 4 remote thermal diode monitors, an internal/local ambient temperature sensor, 2 PROCHOT monitors, 4 fan tachometers, 8 GPIOs, THERMTRIP monitor for masking error events, 2 sets of 7 VID inputs, an ALERT output and all the associated limit registers on a single chip, and communicates to the rest of the baseboard over the System Management Bus (SMBus). The LM94 also provides 2 PWM outputs and associated fan control logic for controlling the speed of system fans. There are two sets of fan control logic, a lookup table and a PI (proportional/integral) loop controller. The lookup table and PI controller are interactive, such that the fans run at the fastest required speed. Upon a temperature or fan tach error event, the PWM outputs may be programmed such that they automatically boost to 100% duty cycle. A timer is included that sets the minimum time that the fans are in the boost condition when activated by a fan tach error. The LM94 incorporates National Semiconductor's TruTherm technology for precision "Remote Diode" readings of processors on 90nm process geometry or smaller. Readings from the external thermal diodes and the internal temperature sensor are made available as an 9-bit two's-complement digital value with the LSb representing 0.5C. Filtered temperature readings are available as a 12-bit two'scomplement digital value with the LSb representing 0.0625C. The LM94 has logic that ties a set of dynamically moving VID inputs to their associated Vccp analog input for real time window comparison fault determination. Voltage mapping for VRD10, VRD10 extended and VRD11are supported by the LM94. When VRD10 mode is selected GPI8 and GPI9 can be used to detect external error flags whose state is be reflected in the status registers. Error events are captured in two sets of mirrored status registers (BMC Error Status Registers and Host Status Registers) allowing two controllers access to the status information without any interference. The LM94's ALERT output supports interrupt mode or comparator mode of operation. The comparator mode is only functional for thermal monitoring. The LM94 provides a number of internal registers, which are detailed in the register section of this document. 12.0 Please contact your local sales office for complete LM94 applications information. 13.0 Registers 13.1 REGISTER WARNINGS In most cases, reserved registers and register bits return zero when read. This should not be relied upon, since reserved registers can be used for future expansion of the LM94 functions. Some registers have "N/D" for their default value. This means that the power-up default of the register is not defined. In the case of value registers, care should be taken to ensure that software does not read a value register until the associated measurement function has acquired a measurement. This applies to temperatures, voltages, fan RPM, and PROCHOT monitoring. 9 www.national.com LM94 13.0 Registers (Continued) 13.2 REGISTER SUMMARY TABLE Register Key Term Lock Register Name Description N/D Not Defined N/A Not Applicable R Read Only R/W Read or Write RWC Read or Write to Clear Address Description FACTORY REGISTERS x XOR Test 00h Used to set the XOR test tree mode SMBus Test 01h SMBus read/write test register Reserved 02h-04h "REMOTE DIODE" MODE SELECT x Transistor Mode Select 05h Selects Diode Mode (default) or Transistor Mode for "Remote Diode" measurements Zone 1b (CPU1 Diode b) Temp 06h Measured value of remote thermal diode temperature channel 1b Zone 2b (CPU2 Diode b) Temp 07h Measured value of remote thermal diode temperature channel 2b Zone 1b (CPU1 Diode b) Filtered Temp 08h Filtered value of remote thermal diode temperature channel 1b Zone 2b (CPU2 Diode b) Fitlered Temp 09h Filtered value of remote thermal diode temperature channel 2b PWM1 8-bit Duty Cycle Value 0Ah 8- bit value of the PWM1 duty cycle. PWM2 8-bit Duty Cycle Value 0Bh 8-bit value of the PWM2 duty cycle VALUE REGISTER SECTION 1 HIGH RESOLUTION PWM OVERIDE REGISTERS x PWM1 Duty Cycle Override (low byte) 0Ch Lower byte of the high resolution PWM1 duty cycle register x PWM1 Duty Cycle Override (high byte) 0Dh Upper byte of the high resolution PWM1 duty cycle register x PWM2 Duty Cycle Override (low byte) 0Eh Lower byte of the high resolution PWM2 duty cycle register x PWM2 Duty Cycle Override (high byte) 0Fh Upper byte of the high resolution PWM2 duty cycle register EXTENDED RESOLUTION TEMPERATURE VALUE REGISTERS Z1a_LSB 10h Zone 1a (CPU1) extended resolution unfiltered temperature value register, least-significant byte Z1a_MSB 11h Zone 1a (CPU1) extended resolution unfiltered temperature value register, most-significant byte Z1b_LSB 12h Zone 1b (CPU1) extended resolution unfiltered temperature value register, least-significant-byte Z1b_MSB 13h Zone 1b (CPU1) extended resolution unfiltered temperature value register, most-significant byte Z2a_LSB 14h Zone 2a (CPU2) extended resolution unfiltered temperature value register, least-significant-byte Z2a_MSB 15h Zone 2a (CPU2) extended resolution unfiltered temperature value register, most-significant byte www.national.com 10 Lock LM94 13.0 Registers (Continued) Register Name Address Description EXTENDED RESOLUTION TEMPERATURE VALUE REGISTERS Z2b_LSB 16h Zone 2b (CPU2) extended resolution unfiltered temperature value register, least-significant-byte Z2b_MSB 17h Zone 2b (CPU2) extended resolution unfiltered temperature value register, most-significant byte Z1a_F_LSB 18h Zone 1a (CPU1) extended resolution filtered temperature value register, least-significant byte Z1a_F_MSB 19h Zone 1a (CPU1) extended resolution filtered temperature value register, most-significant byte Z1b_F_LSB 1Ah Zone 1b (CPU1) extended resolution filtered temperature value register, least-significant-byte Z1b_F_MSB 1Bh Zone 1b (CPU1) extended resolution filtered temperature value register, most-significant byte Z2a_F_LSB 1Ch Zone 2a (CPU2) extended resolution filtered temperature value register, least-significant-byte Z2a_F_MSB 1Dh Zone 2a (CPU2) extended resolution filtered temperature value register, most-significant byte Z2b_F_LSB 1Eh Zone 2b (CPU2) extended resolution filtered temperature value register, least-significant-byte Z2b_F_MSB 1Fh Zone 2b (CPU2) extended resolution filtered temperature value register, most-significant byte Z3_LSB 20h Zone 3 (Internal) extended resolution temperature value register, least-significant byte Z3_MSB 21h Zone 3 (Internal) extended resolution temperature value register, least-significant byte Z4_LSB 22h Zone 4 (External Digital) extended resolution temperature value register, most-significant byte Z4_MSB 23h Zone 4 (External Digital) extended resolution temperature value register, least-significant byte Reserved 24h-30h PI LOOP AND FAN CONTROL SETUP REGISTERS x Temperature Source Select 31h Selects the temperature source for some temperature zones. x PWM Filter Settings 32h Sets the IIR filter coefficients for the PWM outputs for low resolution sources x PWM1 Filter Shutoff Threshold 33h PWM1 Filter Shutoff Threshold x PWM2 Filter Shutoff Threshold 34h PWM2 Filter Shutoff Threshold x PI/LUT Fan Control Bindings 35h PI/LUT fan control binding configuration x PI Controller Minimum PWM and Hysteresis 36h PI Controller Minimum PWM and Hysteresis settings x Zone 1 Tcontrol 37h Zone 1 (CPU1) PI Controller Target Temperature (Tcontrol) x Zone 2 Tcontrol 38h Zone 2 (CPU2) PI Controller Target Temperature (Tcontrol) x Zone 1 Toff 39h Zone 1 (CPU1) PI Controller Off Temperature (Toff) x Zone 2 Toff 3Ah Zone 2 (CPU2) PI Controller Off Temperature (Toff) x P Coefficient 3Bh PI controller proportional coefficient x I Coefficient 3Ch PI controller integral coefficient x PI Exponents 3Dh PI controller coefficient exponents 3Eh Contains manufacturer ID code DEVICE IDENTIFICATION REGISTERS Manufacturer ID 11 www.national.com LM94 13.0 Registers Lock (Continued) Register Name Address Description PI LOOP AND FAN CONTROL SETUP REGISTERS Version/Stepping 3Fh Contains code for major and minor revisions B_Error Status 1 40h BMC error status register 1 B_Error Status 2 41h BMC error register 2 B_Error Status 3 42h BMC error register 3 B_Error Status 4 43h BMC error register 4 B_P1_PROCHOT Error Status 44h BMC error register for P1_PROCHOT B_P2_PROCHOT Error Status 45h BMC error register for P2_PROCHOT B_GPI Error Status 46h BMC error register for GPIs B_Fan Error Status 47h BMC error register for Fans H_Error Status 1 48h HOST error status register 1 H_Error Status 2 49h HOST error register 2 H_Error Status 3 4Ah HOST error register 3 H_Error Status 4 4Bh HOST error register 4 H_P1_PROCHOT Error Status 4Ch HOST error register for P1_PROCHOT BMC ERROR STATUS REGISTERS HOST ERROR STATUS REGISTERS H_P2_PROCHOT Error Status 4Dh HOST error register for P2_PROCHOT H_GPI Error Status 4Eh HOST error register for GPIs H_Fan Error Status 4Fh HOST error register for Fans Zone 1a (CPU1) Temp 50h Measured value of remote thermal diode temperature channel 1a Zone 2a (CPU2) Temp 51h Measured value of remote thermal diode temperature channel 2a VALUE REGISTERS SECTION 2 Zone 3 (Internal) Temp 52h Measured temperature from on-chip sensor Zone 4 (External Digital) Temp 53h Measured temperature from external temperature sensor Zone 1a (CPU1) Filtered Temp 54h Filtered value of remote thermal diode temperature channel 1a Zone 2a (CPU2) Filtered Temp 55h Filtered value of remote thermal diode temperature channel 2a AD_IN1 Voltage 56h Measured value of AD_IN1 AD_IN2 Voltage 57h Measured value of AD_IN2 AD_IN3 Voltage 58h Measured value of AD_IN3 AD_IN4 Voltage 59h Measured value of AD_IN4 AD_IN5 Voltage 5Ah Measured value of AD_IN5 AD_IN6 Voltage 5Bh Measured value of AD_IN6 AD_IN7 Voltage 5Ch Measured value of AD_IN7 AD_IN8 Voltage 5Dh Measured value of AD_IN8 AD_IN9 Voltage 5Eh Measured value of AD_IN9 AD_IN10 Voltage 5Fh Measured value of AD_IN10 AD_IN11 Voltage 60h Measured value of AD_IN11 AD_IN12 Voltage 61h Measured value of AD_IN12 AD_IN13 Voltage 62h Measured value of AD_IN13 AD_IN14 Voltage 63h Measured value of AD_IN14 AD_IN15 Voltage 64h Measured value of AD_IN15 AD_IN16 Voltage 65h Measured value of AD_IN16 (VDD 3.3V S/B) Reserved 66h Current P1_PROCHOT 67h www.national.com Measured P1_PROCHOT throttle percentage 12 Lock LM94 13.0 Registers (Continued) Register Name Address Description VALUE REGISTERS SECTION 2 Average P1_PROCHOT 68h Average P1_PROCHOT throttle percentage Current P2_PROCHOT 69h Measured P2_PROCHOT throttle percentage Average P2_PROCHOT 6Ah Average P2_PROCHOT throttle percentage GPI State 6Bh Current GPIO state P1_VID 6Ch Current VID value of Processor 1 P2_VID 6Dh Current VID value of Processor 2 FAN Tach 1 LSB 6Eh Measured FAN Tach 1 LSB FAN Tach 1 MSB 6Fh Measured FAN Tach 1 MSB FAN Tach 2 LSB 70h Measured FAN Tach 2 LSB FAN Tach 2 MSB 71h Measured FAN Tach 2 MSB FAN Tach 3 LSB 72h Measured FAN Tach 3 LSB FAN Tach 3 MSB 73h Measured FAN Tach 3 MSB FAN Tach 4 LSB 74h Measured FAN Tach 4 LSB FAN Tach 4 MSB 75h Measured FAN Tach 4 MSB Reserved 76h-77h TEMPERATURE LIMIT REGISTERS Zone 1 (CPU1) Low Temp 78h Low limit for external thermal diode temperature channel 1 (D1) measurement Zone 1 (CPU1) High Temp 79h High limit for external thermal diode temperature channel 1 (D1) measurement Zone 2 (CPU2) Low Temp 7Ah Low limit for external thermal diode temperature channel 2 (D2) measurement Zone 2 (CPU2) High Temp 7Bh High limit for external thermal diode temperature channel 2 (D2) measurement Zone 3 (Internal) Low Temp 7Ch Low limit for local temperature measurement Zone 3 (Internal) High Temp 7Dh High limit for local temperature measurement Zone 4 (External Digital) Low Temp 7Eh Low limit for external digital temperature sensor Zone 4 (External Digital) High Temp 7Fh High limit for external digital temperature sensor x Fan Boost Temp Zone 1 80h Zone 1 (CPU1) fan boost temperature x Fan Boost Temp Zone 2 81h Zone 2 (CPU2) fan boost temperature x Fan Boost Temp Zone 3 82h Zone 3 (Internal) fan boost temperature x Fan Boost Temp Zone 4 83h Zone 4 (External Digital) fan boost temperature Zone1 and Zone 2 Hysteresis 84h Zone 1 and Zone 2 hysteresis for limit comparisons Zone 3 and Zone 4 Hysteresis 85h Zone 3 and Zone 4 hysteresis for limit comparisons Reserved 86h-8Dh ZONE 1b and 2b TEMPERATURE READING ADJUSTMENT REGISTERS Zone 1b Temp Adjust 8Eh Allows all Zone 1b temperature measurements to be adjusted by a programmable offset. Zone 2b Temp Adjust 8Fh Allows all Zone 2b temperature measurements to be adjusted by a programmable offset. 13 www.national.com LM94 13.0 Registers Lock (Continued) Register Name Address Description OTHER LIMIT REGISTERS AD_IN1 Low Limit 90h Low limit for analog input 1 measurement AD_IN1 High Limit 91h High limit for analog input 1 measurement AD_IN2 Low Limit 92h Low limit for analog input 2 measurement AD_IN2 High Limit 93h High limit for analog input 2 measurement AD_IN3 Low Limit 94h Low limit for analog input 3 measurement AD_IN3 High Limit 95h High limit for analog input 3 measurement AD_IN4 Low Limit 96h Low limit for analog input 4 measurement AD_IN4 High Limit 97h High limit for analog input 4 measurement AD_IN5 Low Limit 98h Low limit for analog input 5 measurement AD_IN5 High Limit 99h High limit for analog input 5 measurement AD_IN6 Low Limit 9Ah Low limit for analog input 6 measurement AD_IN6 High Limit 9Bh High limit for analog input 6 measurement AD_IN7 Low Limit 9Ch Low limit for analog input 7 measurement AD_IN7 High Limit 9Dh High limit for analog input 7 measurement AD_IN8 Low Limit 9Eh Low limit for analog input 8 measurement AD_IN8 High Limit 9Fh High limit for analog input 8 measurement AD_IN9 Low Limit A0h Low limit for analog input 9 measurement AD_IN9 High Limit A1h High limit for analog input 9 measurement AD_IN10 Low Limit A2h Low limit for analog input 10 measurement AD_IN10 High Limit A3h High limit for analog input 10 measurement AD_IN11 Low Limit A4h Low limit for analog input 11 measurement AD_IN11 High Limit A5h High limit for analog input 11 measurement AD_IN12 Low Limit A6h Low limit for analog input 12 measurement AD_IN12 High Limit A7h High limit for analog input 12 measurement AD_IN13 Low Limit A8h Low limit for analog input 13 measurement AD_IN13 High Limit A9h High limit for analog input 13 measurement AD_IN14 Low Limit AAh Low limit for analog input 14 measurement AD_IN14 High Limit ABh High limit for analog input 14 measurement AD_IN15 Low Limit ACh Low limit for analog input 15 measurement AD_IN15 High Limit ADh High limit for analog input 15 measurement AD_IN16 Low Limit AEh Low limit for analog input 16 measurement AD_IN16 High Limit AFh High limit for analog input 16 measurement P1_PROCHOT User Limit B0h User settable limit for P1_PROCHOT P2_PROCHOT User Limit B1h User settable limit for P2_PROCHOT Vccp1 Limit Offsets B2h VID offset values for window comparator for CPU1 Vccp (AD_IN7) Vccp2 Limit Offsets B3h VID offset values for window comparator for CPU2 Vccp (AD_IN8) FAN Tach 1 Limit LSB B4h FAN Tach 1 Limit LSB FAN Tach 1 Limit MSB B5h FAN Tach 1 Limit MSB FAN Tach 2 Limit LSB B6h FAN Tach 2 Limit LSB FAN Tach 2 Limit MSB B7h FAN Tach 2 Limit MSB FAN Tach 3 Limit LSB B8h FAN Tach 3 Limit LSB FAN Tach 3 Limit MSB B9h FAN Tach 3 Limit MSB FAN Tach 4 Limit LSB BAh FAN Tach 4 Limit LSB www.national.com 14 Lock LM94 13.0 Registers (Continued) Register Name Address Description OTHER LIMIT REGISTERS FAN Tach 4 Limit MSB BBh FAN Tach 4 Limit MSB Special Function Control 1 BCh Controls the hysteresis for voltage limit comparisons. Also selects filtered or unfiltered temperature usage for temperature limit comparisons and fan control. Special Function Control 2 BDh Enables smart tach detection. Also selects 0.5C or 1.0C resolution for fan control. x GPI / VID Level Control BEh Control the input threshold levels for the P1_VIDx, P2_VIDx and GPIO_x inputs. x PWM Ramp Control BFh Controls the ramp rate of the PWM duty cycle when VRDx_HOT is asserted, as well as the ramp rate when PROCHOT exceeds the user threshold. x Fan Boost Hysteresis (Zones 1/2) C0h Fan Boost Hysteresis for zones 1 and 2 x Fan Boost Hysteresis (Zones 3/4) C1h Fan Boost Hysteresis for zones 3 and 4 x Zones 1/2 Spike Smoothing Control C2h Configures Spike Smoothing for zones 1 and 2 x LUT 1/2 MinPWM and Hysteresis C3h Controls MinPWM and hysteresis setting for LUT 1 and 2 auto-fan control x LUT 3/4 MinPWM and Hysteresis C4h Controls MinPWM and hysteresis setting for LUT 3 and 4 auto-fan control GPO C5h Controls the output state of the GPIO pins SETUP REGISTERS PROCHOT Control C6h Controls assertion of P1_PROCHOT or P2_PROCHOT PROCHOT Time Interval C7h Configures the time window over which the PROCHOT inputs are measured x PWM1 Control 1 C8h Controls PWM control source bindings. x PWM1 Control 2 C9h Controls PWM override and output polarity x PWM1 Control 3 CAh Controls PWM spin-up duration and duty cycle x PWM1 Control 4 CBh Frequency control for PWM1. x PWM2 Control 1 CCh Controls PWM control source bindings. x PWM2 Control 2 CDh Controls PWM override and output polarity x PWM2 Control 3 CEh Controls PWM spin-up duration and duty cycle x PWM2 Control 4 CFh Frequency control for PWM2 x LUT 1 Base Temperature D0h Base temperature to which look-up table offset is applied for LUT 1 x LUT 2 Base Temperature D1h Base temperature to which look-up table offset is applied for LUT 2 x LUT 3 Base Temperature D2h Base temperature to which look-up table offset is applied for LUT 3 x LUT 4 Base Temperature D3h Base temperature to which look-up table offset is applied for LUT 4 x Step 2 Temp Offset D4h Step 2 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 3 Temp Offset D5h Step 3 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 4 Temp Offset D6h Step 4 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 5 Temp Offset D7h Step 5 LUT 1/2 and LUT 3/4 Offset Temperatures 15 www.national.com LM94 13.0 Registers Lock (Continued) Register Name Address Description SETUP REGISTERS x Step 6 Temp Offset D8h Step 6 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 7 Temp Offset D9h Step 7 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 8 Temp Offset DAh Step 8 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 9 Temp Offset DBh Step 9 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 10 Temp Offset DCh Step 10 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 11 Temp Offset DDh Step 11 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 12 Temp Offset DEh Step 12 LUT 1/2 and LUT 3/4 Offset Temperatures x Step 13 Temp Offset DFh Step 13 LUT 1/2 and LUT 3/4 Offset Temperatures TACH to PWM Binding E0h Controls the tachometer input to PWM output binding x Tach Boost Control E1h Controls the fan boost function upon a tach error x LM94 Status/Control E2h Gives Master error status, ASF reset control and Max PWM control x LM94 Configuration E3h Configures various outputs and provides START bit SLEEP STATE CONTROL AND MASK REGISTERS Sleep State Control E4h Used to communicate the system sleep state to the LM94 S1 GPI Mask E5h Sleep state S1 GPI error mask register S1 Fan Mask E6h Sleep state S1 fan tach error mask register S3 GPI Mask E7h Sleep state S3 GPI error mask register S3 Fan Mask E8h Sleep state S3 fan tach error mask register S3 Temperature/Voltage Mask E9h Sleep state S3 temperature or voltage error mask register S4/5 GPI Mask EAh Sleep state S4/5 GPI error mask register S4/5 Temperature/Voltage Mask EBh Sleep state S4/5 temperature or voltage error mask register OTHER MASK REGISTERS GPI Error Mask ECh Error mask register for GPI faults Miscellaneous Error Mask EDh Error mask register for VRDx_HOT, GPI, and dynamic Vccp limit checking. ZONE 1a AND 2a TEMPERATURE READING ADJUSTMENT REGISTERS Zone 1a Temp Adjust EEh Allows all Zone 1a temperature measurements to be adjusted by a programmable offset Zone 2a Temp Adjust EFh Allows all Zone 2a temperature measurements to be adjusted by a programmable offset Block Write Command F0h SMBus Block Write Command Code Block Read Command F1h SMBus Block Write/Read Process call Fixed Block 0 F2h Fixed block code address 40h, size 8 bytes Fixed Block 1 F3h Fixed block code address 48h, size 8 bytes Fixed Block 2 F4h Fixed block code address 50h, size 6 bytes Fixed Block 3 F5h Fixed block code address 56h, size 16 bytes Fixed Block 4 F6h Fixed block code address 67h, size 4 bytes Fixed Block 5 F7h Fixed block code address 6Eh, size 8 bytes Fixed Block 6 F8h Fixed block code address 78h, size 12 bytes Fixed Block 7 F9h Fixed block code address 90h, size 32 bytes Fixed Block 8 FAh Fixed block code address B4h, size 8 bytes Fixed Block 9 FBh Fixed block code address C8h, size 8 bytes Fixed Block 10 FCh Fixed block code address D0h, size 16 bytes BLOCK COMMANDS www.national.com 16 Lock LM94 13.0 Registers (Continued) Register Name Address Description BLOCK COMMANDS Fixed Block 11 FDh Fixed block code address E5h, size 9 bytes Reserved FEh-FFh Reserved for future commands Please contact your local sales office for complete LM94 applications information. 17 www.national.com LM94 14.0 Absolute Maximum Ratings (Notes 1, 2) ESD Susceptibility (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Positive Supply Voltage (VDD) 300V Charged Device Model 750V -65C to +150C Soldering process must comply with National's reflow temperature profile specifications. Refer to www.national.com/packaging/. (Note 5) -0.3V to 6.0V (Except Analog Inputs) Voltage on +5V Input 3 kV Machine Model Storage Temperature 6.0V Voltage on Any Digital Input or Output Pin Human Body Model 15.0 Operating Ratings (Notes 1, 2) -0.3V to +6.667V Voltage at Positive Remote Diode Inputs, AD_IN1, AD_IN2, AD_IN3, and AD_IN15 Inputs -0.3V to (VDD + 0.05V) TMIN TA TMAX 0C TA +85C Operating Temperature Range Nominal Supply Voltage Voltage at Other Analog Voltage Inputs 3.3V Supply Voltage Range (VDD) -0.3V to +6.0V +3.0V to +3.6V VID0-VID5 Input Current at Thermal Diode Negative Inputs Input Current at any pin (Note 3) 1 mA 10mA Package Input Current (Note 3) 100 mA Maximum Junction Temperature (Note 9) (TJMAX) 150 C -0.05V to +5.5V Digital Input Voltage Range -0.05V to (VDD + 0.05V) Package Thermal Resistance (Note 6) 79C/W DC Electrical Characteristics The following limits apply for +3.0 VDC to +3.6 VDC, unless otherwise noted. Bold face limits apply for TA = TJ over TMIN to TMAX of the operating range; all other limits TA = TJ = 25C unless otherwise noted. TA is the ambient temperature of the LM94; TJ is the junction temperature of the LM94; TD is the junction temperature of the thermal diode. Symbol Parameter Typical (Note 9) Limits (Note 10) Units (Limits) Converting, Interface and Fans Inactive, Peak Current 2 2.75 mA (max) Converting, Interface and Fans Inactive, Average Current 1.6 Conditions POWER SUPPLY CHARACTERISTICS Power Supply Current Power-On Reset Threshold Voltage 2 mA 1.6 V (min) 2.7 V (max) 3 2.5 C (max) TEMPERATURE-TO-DIGITAL CONVERTER CHARACTERISTICS 0C TA 85C Local Temperature Accuracy Over Full Range TA = +55C Local Temperature Resolution 1 0C TA 85C and 0C TD 100C Remote Thermal Diode Temperature Accuracy Over Full Range; targeted for a typical Pentium processor on 90 nm or 65 nm process(Note 8) 0C TA 85C and TD =70C Remote Thermal Diode Temperature Accuracy; targeted for a typical Pentium processor on 90nm or 65nm process (Note 8) 0C TA 85C and 25C TD 70C 1 High Level 172 Low Level 10.75 Remote Temperature Resolution Thermal Diode Current Ratio www.national.com C (max) C 3 C (max) 2.5 C (max) C 1 Thermal Diode Source Current TC 2 1 C 230 A (max) A 16 Total Monitoring Cycle Time 100 18 ms (max) (Continued) The following limits apply for +3.0 VDC to +3.6 VDC, unless otherwise noted. Bold face limits apply for TA = TJ over TMIN to TMAX of the operating range; all other limits TA = TJ = 25C unless otherwise noted. TA is the ambient temperature of the LM94; TJ is the junction temperature of the LM94; TD is the junction temperature of the thermal diode. Symbol Parameter Conditions Typical (Note 9) Limits (Note 10) Units (Limits) 2 % of FS (max) ANALOG-TO-DIGITAL VOLTAGE MEASUREMENT CONVERTER CHARACTERISTICS TUE Total Unadjusted Error (Note 12) DNL Differential Non-Linearity PSS Power Supply (VDD) Sensitivity TC Total Monitoring Cycle Time Input Resistance for Inputs with Dividers 1 LSB 1 %/V (of FS) 200 AD_IN1- AD_IN3 and AD_IN15 Analog Input Leakage Current (Note 13) 100 ms (max) 140 k (min) 60 nA (max) 1 % (max) 2.525 2.475 V (max) V (min) REFERENCE OUTPUT (VREF) CHARACTERISTICS Tolerance VREF Output Voltage (Note 14) 2.500 ISOURCE = -2 mA ISINK = 2 mA Load Regulation 0.1 % DIGITAL OUTPUTS: PWM1, PWM2 IOL Maximum Current Sink VOL Output Low Voltage 8 mA (min) IOUT = 8.0 mA 0.4 V (max) IOUT = 4.0 mA 0.4 V (min) IOUT = 6 mA 0.55 V (min) 10 A (max) 32 mA (max) DIGITAL OUTPUTS: ALL VOL Output Low Voltage (Note excessive current flow causes self-heating and degrades the internal temperature accuracy.) IOH High Level Output Leakage Current IOTMAX Maximum Total Sink Current for all Digital Outputs Combined VOUT = VDD CO Digital Output Capacitance 0.1 20 pF DIGITAL INPUTS: ALL VIH Input High Voltage Except Address Select 2.1 V (min) VIL Input Low Voltage Except Address Select 0.8 V (max) VIH Input High Voltage for Address Select 90% VDD V (min) VIM Input Mid Voltage for Address Select 43% VDD 57% VDD V (min) V (max) 10% VDD V (max) VIL Input Low Voltage for Address Select VHYST DC Hysteresis 0.3 V IIH Input High Current VIN = VDD -10 A (min) IIL Input Low Current VIN = 0V 10 A (max) CIN Digital Input Capacitance 20 pF DIGITAL INPUTS: P1_VIDx, P2_VIDx, GPI_9, GPI_8, GPIO_7, GPIO_6, GPIO_5, GPIO_4 (When respective bit set in Register BEh GPI/VID Level Control) VIH Alternate Input High Voltage (AGTL+ Compatible) 0.8 V (min) VIL Alternate Input Low Voltage (AGTL+ Compatible) 0.4 V (max) 19 www.national.com LM94 DC Electrical Characteristics LM94 AC Electrical Characteristics The following limits apply for +3.0 VDC to +3.6 VDC, unless otherwise noted. Bold face limits apply for TA = TJ = TMIN to TMAX of the operating range; all other limits TA = TJ = 25C unless otherwise noted. Symbol Parameter Conditions Typical (Note 9) Limits (Note 10) Units (Limits) FAN RPM-TO-DIGITAL CHARACTERISTICS Counter Resolution 14 bits Number of fan tach pulses count is based on 2 pulses Counter Frequency 22.5 Accuracy kHz 6 % (max) 6 6 % (max) 250 330 ms (min) ms (max) PWM OUTPUT CHARACTERISTICS Frequency Tolerances 2 Duty-Cycle Tolerance % (max) RESET INPUT/OUTPUT CHARACTERISTICS Output Pulse Width Upon Power Up Minimum Input Pulse Width Reset Output Fall Time 1.6V to 0.4V Logic Levels 10 s (min) 1 s (max) 10 100 kHz (min) kHz (max) SMBus TIMING CHARACTERISTICS fSMBCLK SMBCLK (Clock) Clock Frequency tBUF SMBus Free Time between Stop and Start Conditions 4.7 s (min) tHD;STA Hold time after (Repeated) Start Condition. After this period, the first clock is generated. 4.0 s (min) tSU;STA Repeated Start Condition Setup Time 4.7 s (min) tSU;STO Stop Condition Setup Time 4.0 s (min) tSU;DAT Data Input Setup Time to SMBCLK High 250 ns (min) tHD;DAT Data Output Hold Time after SMBCLK Low 300 1075 ns (min) ns (max) tLOW SMBCLK Low Period 4.7 50 s (min) s (max) tHIGH SMBCLK High Period 4.0 50 s (min) s (max) tR Rise Time 1 s (max) tF Fall Time 300 ns (max) tTIMEOUT Timeout SMBDAT or SMBCLK low time required to reset the Serial Bus Interface to the Idle State 25 35 ms ms (min) ms (max) 500 ms (max) 400 pF (max) tPOR Time in which a device must be operational after power-on reset CL Capacitance Load on SMBCLK and SMBDAT www.national.com 31 VDD > +2.8V 20 LM94 16.0 Timing Waveform 20112403 17.0 Electrical Notes Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND, unless otherwise noted. Note 3: When the input voltage (VIN) at any pin exceeds the power supplies (VIN < (GND or AGND) or VIN > VDD, except for analog voltage inputs), the current at that pin should be limited to 10 mA. The 100 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to ten. Parasitic components and/or ESD protection circuitry are shown below for the LM94's pins. Care should be taken not to forward bias the parasitic diode, D1, present on pins D+ and D- as shown in circuits C and D. Doing so by more than 50 mV may corrupt temperature measurements. D1 and the ESD Clamp are connected between V+ (VDD, AD_IN16) and GND as shown in circuit B. SNP stands for snap-back device. Pin # Circuit GPIO_0/TACH1 Symbol 1 A GPIO_1/TACH2 2 A GPIO_2/TACH3 3 A GPIO_3/TACH4 4 A GPIO_4 / P1_THERMTRIP 5 A GPIO_5 / P2_THERMTRIP 6 A GPIO_6 7 A GPIO_7 8 A VRD1_HOT 9 A VRD2_HOT 10 A SCSI_TERM1 11 A SCSI_TERM2 12 A SMBDAT 13 A SMBCLK 14 A ALERT/XtestOut 15 A RESET 16 A AGND 17 B (Internally shorted to GND pin.) VREF 18 A REMOTE1- 19 C REMOTE1+ 20 D REMOTE2- 21 C REMOTE+ 22 D 21 All Input Circuits Circuit A Circuit B www.national.com LM94 17.0 Electrical Notes Symbol (Continued) Pin # Circuit AD_IN1 23 D AD_IN2 24 D AD_IN3 25 D AD_IN4 26 E AD_IN5 27 E AD_IN6 28 E AD_IN7 29 E AD_IN8 30 E AD_IN9 31 E AD_IN10 32 E AD_IN11 33 E AD_IN12 34 E AD_IN13 35 E AD_IN14 36 E AD_IN15 37 D ADDR_SEL 38 A AD_IN16/VDD (V+) 39 B GND 40 B (Internally shorted to AGND.) PWM1 41 A PWM2 42 A P1_VID0 43 A P1_VID1 44 A P1_VID2 45 A P1_VID3 46 A P1_VID4 47 A P1_VID5 48 A P1_PROCHOT 49 A P2_PROCHOT 50 A P2_VID0 51 A P2_VID1 52 A P2_VID2 53 A P2_VID3 54 A P2_VID4 55 A P2_VID5 56 A All Input Circuits Circuit C Circuit D Circuit E Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Machine model, 200 pF discharged directly into each pin. Charged device model (CDM) simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an automated assembler) then rapidly being discharged. Note 5: Reflow temperature profiles are different for lead-free and non lead-free packages. Note 6: The maximum power dissipation must be de-rated at elevated temperatures and is dictated by TJMAX, JA and the ambient temperature, TA. The maximum allowable power dissipation at any temperature is PD MAX= (TJMAX - TA) / JA. The JAfor the LM94 when mounted to 1 oz. copper foil PCB the JA with different air flow is listed in the following table. Air Flow Junction to Ambient Thermal Resistance, JA 0 m/s 79 C/W 1.14 m/s (225 LFPM) 62 C/W 2.54 m/s (500 LFPM) 52 C/W Note 7: See the URL "http://www.national.com/packaging/" for other recommendations and methods of soldering surface mount devices. Note 8: At the time of first pubication of this specification (Jan 2006), this specification applies to either Pentium or Xeon Processors on 90nm or 65nm process when TruTherm is selected. When TruTherm is deselected this specification applies to an MMBT3904. This specification does include the error caused by the variability of the diode ideality and series resistance parameters. Note 9: Typical parameters are at TJ = TA = 25 C and represent most likely parametric norm. www.national.com 22 LM94 17.0 Electrical Notes (Continued) Note 10: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 11: TUE (Total Unadjusted Error) includes Offset, Gain and Linearity errors of the ADC. Note 12: Total Monitoring Cycle Time includes all temperature and voltage conversions. Note 13: Leakage current approximately doubles every 20 C. Note 14: A total digital I/O current of 40 mA can cause 6 mV of offset in Vref. Note 15: Timing specifications are tested at the TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge. TRI-STATE output voltage is forced to 1.4V. 23 www.national.com LM94 TruThermTM Hardware Monitor with PI Loop Fan Control for Server Management 18.0 Physical Dimensions inches (millimeters) unless otherwise noted 56-Lead Molded TSSOP Package, JEDEC Registration Number MO-153 Variation EE, Order Number LM94CIMT or LM94CIMTX, NS Package Number MTD56 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560