1/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Chip tantalum capacitors
(Bottom surface electrode type : Large capacitance)
TC Series M Case
Features (M)
With an original bottom surface electrode structure.
1) Excellent adhesion.
2) Easy visual recognition of fillets.
3) Large capacitance, low ESR.
Dimensions (Unit : mm)
M case
Dimensions
L
H
S
W
2
W
1
(Unit : mm)
0.5 0.1
+
−
0.8 0.1
+
−
0.55 0.1
+
−
0.85 0.1
+
−
1.6 0.1
+
−
Anode mark
+−
H
L
Part No. Explanation
M1 A 8 RT 4 7 5C M
Rated voltage Capacitance tolerance
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
8 :
Tape width
R :
Positive electrode on the side opposite to sprocket hole
1
6
13 64
2 5
11 Series name
TC
2
Case style
3
4
Nominal capacitance
5
Taping
20%
M : +
−
4
CODE 6.3
0J 10
1A 16
1C
Rated voltage (V) 0G
2.5
0E
M
2/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Data Sheet TC Series M Case
Rated table
(μF) Rated voltage (V)
Remark) Case size codes (M) in the above show products line-up.
∗ Under development
∗
∗
∗
4
0G
1.0 (105) M
1.5 (155)
2.2 (225)
3.3 (335)
4.7 (475)
6.8 (685)
10 (106) M
MM
MM
M
M
MM
15 (156)
22 (226) MM
33 (336) M
2.5
0E 6.3
0J 10
1A 16
1C
M
20
1D
M
25
1E
M
47 (476) M
Marking
A s
A s
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage : Due to the small size of M case, a voltage code is used as shown below.
(3) Visual typical example (1) voltage code (2) capacitance code
Voltage
Code Rated DC
Voltage (V)
Capacitance
Code
Nominal
Capacitance (μF)
[M case] note 1)
note 2) voltage code and capacitance code are variable with parts number
−
(1)
A
−
(2)
s
g
j
A
C
4
e 2.5
6.3
10
16
D20
E 25
A
E
J
N
S
W
a
e
j
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
n33
s47
3/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Data Sheet TC Series M Case
Characteristics
Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Operating Temperature −55
°C to
+125
°C
Maximum operating
temperature with no voltage
derating
+85
°C
Rated voltage (VDC)
Category voltage (VDC)
Surge voltage (VDC)
DC Leakage current Shall be satisfied the voltage on
" Standard list "
Capacitance tolerance
Measuring frequency : 100
±
10kHz
Measuring voltage : 0.5Vrms or less
Measuring circuit
: DC Equivalent series circuit
Tangent of loss angle
(Df, tan δ)
Impedance
Resistance to
Soldering heat
Temperature
cycle
Moisture
resistance
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C.
Shall be satisfied the voltage on
" Standard list " Measuring frequency : 120
±
12Hz
Measuring voltage : 0.5Vrms +1.5.DC
Measuring circuit
: DC Equivalent series circuit
Shall be satisfied the voltage on
" Standard list "
at 85
°C
at 125
°C
at 85
°C
Voltage : Rated voltage for 5min
Shall be satisfied allowance range.
±
20% Measuring frequency : 120
±
12Hz
Measuring voltage : 0.5Vrms +1.5.DC
Measuring circuit
: DC Equivalent series circuit
Less than 200% of initial limit
Less than 200% of initial limit
Voltage reduction when temperature exceeds +
85°C
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Solder temp : 260
±
5
°C
Duration
:
5
±
0.5s
Repetition
: 1
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C. Less than 200% of initial limit
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60±2°C and 90 to 95% RH,respectiveiy, for 500±12h
leave it at room
temperature for over 24h and then measure the
sample.
Less than 200%
of initial limit
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C. Less than 200% of initial limit
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Less than 200% of initial limit
Temp. Time
1
2
3
4
Room temp.
Room temp.
3min.or less
3min.or less
30±3min.
30±3min.
−55 3°C
+
−
125 2°C
+
−
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Others : Within ±20% of initial value.
TCM0J336 : Within ±30% of initial value.
Others : Within ±20% of initial value.
TCM0J336 : Within ±30% of initial value.
Others : Within ±20% of initial value.
TCM0J336 : Within ±30% of initial value.
16106.34
106.342.5
1385.2
2.5
1.6
3.2 20
20
13
26
25
16
32
4/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Data Sheet TC Series M Case
Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
Temperature
Stability
Surge voltage
Shall be satisfied the voltage on " Standard list "
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
Temp.
Appearance There should be no significant abnormality.
Temp.
−55
°C
+85
°C
Df (tan δ)
L.C.
L.C.
Shall be satisfied the voltage on " Standard list "
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial value
Less than 1000% of initial value
Df (tan δ)
L.C.
Temp.
+125
°C
ΔC / C
ΔC / C
ΔC / C
−
Loading at
High temperature
ΔC / C
Df (tan δ)
L.C.
L.C.
Less than 200% of initial limit
Less than 200% of initial limit
After applying the rated voltage for 1000+36/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of
85±2°C
, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Df (tan δ)Less than 200% of initial limit
Less than 200% of initial limit
ΔC / C
Within ±20% of initial value
There should be no significant abnormality.
Appearance
There should be no significant abnormality.
Appearance
Terminal
strength The measured value should be stable.
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
Capacitance
1
F (Apply force)
(Unit : mm)
20
50
R230
45 45
thickness=1.6mm
TCM0G336
: Within 0/−30% of initial value
TCM0J226 : Within 0/−30% of initial value
TCM0J336 : Within 0/−30% of initial value
Others : Within 0/−15% of initial value
TCM0G336
: Within +15/-5% of initial value
Others : Within +15/0% of initial value
TCM0G336 : Within +20/-5% of initial value
Others : Within +20/0% of initial value
TCM0G336
: Within ±30% of initial value
Others : Within ±20% of initial value
TCM0J226 : Within ±15/−5% of initial value
TCM0J336 : Within ±15/−5% of initial value
TCM0J226 : Within ±30% of initial value
TCM0J336 : Within ±30% of initial value
5/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Data Sheet TC Series M Case
Apply force
a circuit board
product
C105
YAA
Item Performance Test conditions (JIS C 5101−1 and JIS C 5101− 3)
Adhesiveness
Dimensions
The terminal should not come off. As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30
±
5s, at room
temperature.
Solderability 3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm / s
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration
: 3±0.5s
Solder : M705
Flux
: Rosin 25% IPA 75%
Capacitance
Vibration
Appearance
Measure value should not fluctuate during the
measurement.
There should be no significant abnormality.
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board
.
Standard products list, TC series M case
Part No.
Rated
voltage
85°C
(V)
Category
voltage
125°C
(V)
Surge
voltage
85°C
(V)
Cap.
120Hz
(μF)
Tolerance
(%)
Leakage
current
25°C
1WV.300s
(μA)
Df
120Hz
(%)
22 0.9
4.7 0.5
0.6
10
2.5
10 0.5
0.5TC M 0E 476
TC M 0G 106
TC M 0G 226
TC M 0J 475
TC M 0J 106
4.7
TC M 1A 105 1.0
TC M 1A 225
1.6 3.2
4 2.5 5.2
4 2.5 5.2
6.3 4 8
6.3 4 8
10 6.3 13
10 6.3 13
10 6.3 13
16 10 20
2.2
0.5
TC M 1A 475 4.7
TC M 1C 105 1.0 0.5
−55°C
125°C
25°C
85°C
30 20
20
20
20
10
30
30
30
15
30
2030 30
2030 30
30
30
1015 15
2030 30
30
15
Impedance
100kHz
(Ω)
9.0
33 13.0TC M 0G 336 4 2.5 5.2 3060 40 9.0
9.0
9.0
13.0
22
TC M 0J 226 6.3 4 8 3060 40 9.0
208
33
TC M 0J 336 6.3 4 8 3060 40 9.0
15.0
9.0
9.0
9.0
15.0
16 10 20
TC M 1C 225 2.2 0.5 2030 30 13.5
13.50.5
0.5
10 6.3 13
TC M 1A 106 10 2030 30 9.010.0
=Tolerance (M : )
+
−20%
20
+
−
20
+
−
20
+
−
20
+
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
6/6
www.rohm.com
○
c 2011 ROHM Co., Ltd. All rights reserved. 2011.11 - Rev.H
Data Sheet TC Series M Case
Packaging specifications
Case code
M
A 0.1
+
−B 0.1
+
−W 0.2
+
−E 0.1
+
−F 0.05
+
−P1 0.1
+
−P2
0.05
+
−P0 0.1
+
−
1.0 1.8 8.0 1.75 3.5 4.0 2.0 4.0
t1
0.05
+
− t2 0.1
+
−
0.20 1.0
Taping [M case]
Feeding direction
P
1
B
A
P
2
P
0
FW
E
t2
t1φ1.5
+0.1
0
(Unit : mm)
Packaging style
4,000pcs
Case code Packaging
Taping
M case
Packaging style
plastic taping φ180mm Reel
Symbol
R
Basic ordering unit
s
Reel [M case]
φ13 0.2
φ60 +1
0
0
−1.5
φ180
9.0
11.4 1.0
Label sticking position
EIAJ ET−7200A
Pull direction
+
−+1.0
0
+
−
(Unit : mm)
R1120A
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Notice
ROHM Customer Support System
http://www.rohm.com/contact/
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
Notes
