PERRIN TECHNICAL DATA Page i / 4 STRAIGHT PLUG RECEPTACLE FOR PCB PRESS FIT LEGS R114.41 6.000 SM BOoOY OUTER CONTACT CENTER CONTACT INSULATOR GASKET OTHERS PIECES : BRASS i BRASS i PTFE PHOSPHOR BRONZE aa} For DIA 0.0391:8938. plated holes 1 0.1 0.209 . 0.083 (01988) PERCAGE PANNEAU DIA 0.35 (2.54) (5.3) |(2.1) MOUNTING HOLE (29) \ | | | ro OF A i tf | |_| | hess > Q- ac BOIA - yt a] | [8 SS shores ? 0.2 | 0.474 MM INCH | (5.08) square 0.276 (12.05) maxi | mini | maxi | mini (7) A [2.565 [2.515/0.101/0.1 0.4 B 11.09 [0.94 |0.043/0.037 (2.54} C /5.105/5.055/0.201/0.199 NOMINAL IMPEDANCE 50 0 : CABLES : FREQUENCY RANGE 0-4 GHz TEMPERATURE RATING -65/+165 c V.S.W.R 1.3 + x F(GHZ} Maxi: RF INSERTION LOSS 0.4 JF(GHz) aB Maxi: VOLTAGE RATING 00 veff Maxi! DIELECTRIC WITHSTANDING VOLTAGE 1000 veff Mini! INSULATION RESISTANCE 1000 Mamini : OTHERS CHARACTERISTICS 3,0: HERMETIC SEAL NA Atm.om si CABLE RETENTION NAN Mini LEAKAGE (pressurized only) NA : CENTER CONTACT RETENTION MECHANICAL DURABILITY 500 cycles Axial force - mating end 40 N Mini Axial force - opposite end 40 N Mini WEIGHT -92 gr : Torque NA cm.N Mini SPECIFICATION : RECOMMENDED TORQUES Mating NA cm.N Panel nut NA cm.N Clamp nut NA om.N ali values are given CONNECTOR PARTS, MATERIALS FINISH (or mereestane siven GOLD 0.2 OVER NICKEL 2 :GOLD 0.5 OVER NICKEL 2 ?TIN 3 OVER NICKEL 1-2 ISSUE 0540B CREATION DATE 17/12/1996 FILE 95- ra PART-NUMBER 0132-018 RADIALL WN The information given here is subject to change without notice. Design changes may be in order to improve the product . Connect to the futurePERRIN TECHNICAL DATA Page 2/7 4 aL | RADIALL R114.416.000 ISSUE 0540B jSERIES SMB PC BOARD GLASS FIBRE EPOXYD NEMA:G10,611,FR4,FR5 MATERIAL DIN 40802 : EP-GC 01 , EP-GC 02 THICKNESS 1.6 mm * HOLE FOR 1mm COMPLIANT PIN BORE-HOLE $1.45 0/-0.03 COPPER > 25 ym TIN < 15 jym FINAL DIAMETER #1 +0.09/-0.06 Ol oO 41.15 5 03 wo Cu 25 yym mini Od Sn 45 jum maxil |) = wo ie - iY] o y Cc x Oo y c ~~ Y a Vb. kod i o1 70:08 The information given hare is subject to change without notice.Design changes may be in order to improve the product.PERRIN TECHNICAL DATA Page 3 / 4 Pea RADIALL R114.416.000 ISSUE 0540B SERIES 14s SMB MOUNTING INSTRUCTIONS ON THE PCB STRAIGHT CONNECTORS WITH PRESS-FIT TERMINATION Slide the upper tool (R282.878.151) ipo into the machine (press) . ro ; - 1 i - Press I - 3 - ~=[ T~ Upper tool T] Slide the lower too1(R282.878.523) Loy into the base and place correctly the PCB IPS| on this tool .(positioning pins) - Lower tool | | positionin - 1 pins - Base Place correctly the straight connector \ with press-fit termination on the PCB and introduce the press-fit extremity in the holes of the PCB . Push on the top (about 500 N) until total insertion .{in direction F) (Push connector body until it bottoms against PCB) . Remove the connector and the PCB | r assembly . = The information given here is subject to change without notice.Oasign changes may be in order to improve tha product.PERRIN TECHNICAL DATA Page 4 / 4 ly ala RADIALL tt | FA) a R114.416.000 ISSUE 0540B SERIES REPLACEMENT INSTRUCTIONS ON THE PCB STRAIGHT AND RIGHT ANGLE CONNECTORS WITH PRESS-FIT TERMINATION SMB Place correctly the PCB and the connector on lower tool (R282.878.533) Lower tool MATZ-_-VWZA Base Place the upper tool (R282.878.513) at the back of the connector and place correctly the ejectors : - on Press-fit pins (if PCB thickness < 4.5mm) - in the holes of the PCB (if PCB thickness > 4.5mm) Press Upper tool Press the back of the upper tool to remove the connector ( about 00N) into the connector slide down onto lower tool . Lower taol Ejectors CAUTION ! It's impossible to use a COAXIPRESS a twice . A plated hole of the PCB can't be used over 3 times . * panel thickness: 1.6 to 7 mm The information given here is subject ta change without notice.Design changes may be in order to improve the product.