V-1www.hubbell-wiring.com Wiring Device-Kellems
®
Section V
Kellems® Wire Management Products
Pulling Grips
Strain Relief Grips
Support Grips
Liquidtight Conduit,
Tubing and Fittings
Index
Product Page
Kellems® Wire Mesh Grips Diagram ..................................V-2
Quick Reference Selection Guide for Grip Applications .................V-4
Pulling Grips .....................................................V-5
Overhead DUA-PULL® Pulling Grips .................................V-6
Overhead Multiple Strength Pulling Grips .............................V-7
Underground K-Type Pulling Grips ..................................V-8
Underground T-Type Pulling Grips ...................................V-9
Special Purpose Pulling Grips .....................................V-10
Low Tension Pulling Grips ........................................V-12
Wire Rope Splicing Grips .........................................V-13
Cable Splicing Grips ............................................V-14
Tools, Bands, and Swivels ........................................V-15
Technical Information ............................................V-17
Support Grips ...................................................V-27
Standard Duty Support Grips .....................................V-30
Heavy Support Grips ............................................V-34
Service Drop Grips ..............................................V-36
Bus Drop Support Grips .........................................V-38
Conduit Riser Grips .............................................V-39
Technical Information ............................................V-41
Fiber Optic Cable Grips ...........................................V-46
Pulling Grips ...................................................V-47
Support Grips ..................................................V-50
Technical Information ............................................V-51
Hose Containment Grips ..........................................V-55
Strain Relief System Selection Chart ................................V-56
Strain Relief Grips for Flexible Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V-57
Deluxe Cord Grips ..............................................V-58
PG and Metric Threaded Deluxe Cord Grips .........................V-62
Dust-Tight Strain Relief Grips .....................................V-63
I-Grips ........................................................V-64
Thread Adapters for Multi-Pin Connectors ...........................V-65
Strain Relief Grips for Liquidtight Conduit ............................V-66
Technical Information ............................................V-69
Cord Connectors .................................................V-77
Straight Male Cord Connectors ....................................V-78
45° and 90° Male Cord Connectors ................................V-81
Straight Female and Underground Feeder ...........................V-82
Low Profile NPT, PG and Metric Thread Connectors ...................V-83
Accessories ...................................................V-84
Hubbell Juniors® Miniature Nylon Cord Connectors. . . . . . . . . . . . . . . . . . . .V-85
Technical Information ............................................V-87
PolyTuff® Non-Metallic Liquidtight Conduit and Tubing .................V-98
PolyTuff® Non-Metallic Liquidtight Fittings ..........................V-100
Metallic Liquidtight Conduit Fittings ...............................V-101
Technical Information ...........................................V-102
www.hubbell-wiring.comV-2 Wiring Device-Kellems
®
Support Grip
Conduit
Support Grip
Overhead
Pulling Grip
Bus Drop
Support Grip
Support Grip
Conduit Support
Underground
Pulling Grip
Flexible
Conduit
Grip
Strain
Relief
Grip
Deluxe
Cord Grip
Support Grip
Bus Drop
Support Grip
Flexible
Conduit Grip
Bus Drop
Support Grip Deluxe Cord Grip
Strain Relief Grip
Underground
Pulling Grip
INDUSTRY
INDUSTRY
UTILITY
UTILITY
COMMERCIAL RESIDENTIAL
Support Grip
To help you fully visualize the variety of uses available to you through Hubbell-Kellems
Mesh Grips, we have prepared this diagram of common applications. It follows the
typical pattern of usage you would find traveling from utility to industrial, commercial
and residential environments.
Pulling Grips are instrumental in the installations of transmission lines, service lines
and cabling for construction and maintenance.
Support Grips provide holding management for indoor and outdoor permanent
cable installations.
Strain Relief Grips are most often used to provide maximum reliability and minimum
maintenance in areas where cords on machinery or equipment is impacted by motion
or vibration or at risk of damage from cable pullout.
Beyond the electrical applications illustrated here, Hubbell-Kellems Mesh Grips can
be used for wire management on radio and microwave communications towers,
crane and hoist wire rope maintenance, elevator cable management and more.
Wire Management Products
Kellems® Wire Mesh Grips Diagram
V-3www.hubbell-wiring.com Wiring Device-Kellems
®
Support Grip
Conduit
Support Grip
Overhead
Pulling Grip
Bus Drop
Support Grip
Support Grip
Conduit Support
Underground
Pulling Grip
Flexible
Conduit
Grip
Strain
Relief
Grip
Deluxe
Cord Grip
Support Grip
Bus Drop
Support Grip
Flexible
Conduit Grip
Bus Drop
Support Grip Deluxe Cord Grip
Strain Relief Grip
Underground
Pulling Grip
INDUSTRY
INDUSTRY
UTILITY
UTILITY
COMMERCIAL RESIDENTIAL
Support Grip
www.hubbell-wiring.comV-4 Wiring Device-Kellems
®
Kellems® Wire Management Products
Quick Reference Selection Guide for Grip Applications
Universal Eye
Used to fasten
around a structure or
closed loop. Available
on standard duty
support and light or
heavy duty service
drop grips. See
pages V-31
and V-35.
Single Eye
For single hook
attachment
of permanent
indoor/outdoor
cable. Available
on heavy-duty,
standard duty,
and service drop
grips. See pages
V-28, V-32, and
V-34.
Heavy-Duty
Rotating Eye
For underground
wiring and overhead
heavy-duty pulling
of service lines and
new construction
cable. See pages
V-7 and V-8.
Deluxe Cord
Indoor or outdoor
use where subject to
moisture, splash, or
washdown. Examples
are enclosures, crane
hoist and pendant
drop stations, hand
tools, pumps,
and processing
equipment. Available
in straight, 90°, or 45°
configurations. See
pages V-58 to V-61.
Single Offset Eye
For offset hook
attachment of
permanent indoor/
outdoor cable.
Available on
standard duty and
light-duty support
grips. See page
V-30.
Light-Duty
Flexible Eye
For light industrial
pulling of electrical
cable and for
underground and
industrial plant wiring
and re-wiring.
See page V-12.
Dust-Tight
Strain Relief
Indoor use only for
wiring of electrical
enclosures,
machine tools,
portable power
tools, bus drop
cable systems.
See page V-63.
Double Eye
For double hook
attachment of
permanent indoor/
outdoor cable.
Available on heavy-
duty and standard
duty grips. See
pages V-29 and
V-33.
Heavy-Duty
Flexible Eye
For overhead
transmission and
distribution line
stringing. See pages
V-6, V-7, and V-9.
Liquid-Tight,
Flexible Metal
Conduit
Wiring of machine
tools, electrical
enclosures, motors,
and systems
subjected to vibration,
flexure, motion, or
strain. Available in
straight, 90°, or 45°
configurations. See
pages V-66 to V-68.
Slack Grips
For removing
underground cable
and pulling slack in
existing cable and
new installations
and when end of
cable is not available.
See pages V-10
and V-11.
Splicing Grips
Used as temporary splice for cable and wire rope, or as reinforcement to protect cables and hoses. See pages V-13 and V-14.
Conduit Riser Grips
Ideal for supporting electrical wires inside rigid conduit via a supporting ring. See pages V-38 to V-40.
Hose Containment Grips
Used on flexible hose lines to prevent violent whipping of hose in the event of failure at the fitting. See page V-55.
Specifications are subject to change without notice.
Support Grips Strain Relief Grips
Support Grips
Pulling Grips
Other Specialty Grips
Wide Range
Bus Drop
Used indoors for
cable support
where flexible
cable connects
electrical
equipment to bus
duct. Support air
hose and water
hose. See page
V-36.
V-5www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Pulling Grips
Overhead, Underground, Commercial Construction, Specialty
Flexible or rotating eyes will mate easily with line stringing swivels
for attachment to pulling lines; they have great strength for
trouble free pulling jobs
Shoulder protectors contain the cable inside the grip and smooth
the passage of the grip over line stringing blocks or conduit bends;
they protect the leading edge of the grip from abrasion
The galvanized steel mesh grip provides strength for secure pulling
jobs and a slim profile with little build-up; it has flexibility to follow
cable path
The multiweave styles available add strength for big pulling jobs
and provide positive gripping power
Endless weave allows easy installation onto cable. It has a snag-free
low profile; designed to be a reusable tool
www.hubbell-wiring.comV-6 Wiring Device-Kellems
®
DUA-PULL® Grips
Diameter Range Approx.
Breaking
Strength
Lbs. (N)
E
Inches (cm)
M
Inches (cm)
Eye B
Diameter
Inches (cm)
Over Cable
and Grip**
Inches (cm) Color Code Catalog Number
Conductor
Inches (cm)
Rope*
Inches (cm)
.19"-.37"
(.48-.94)
.25"-.65"
(.63-1.65)
6,500
(28,912)
10" (25.40) 24" (60.96) .220" (.56) .200" (.51) Black 033271037
.38"-.62"
(.97-1.57)
.50"-.90"
(1.27-2.29)
14,000
(62,272)
12" (30.48) 36" (91.44) .375" (.95) .280" (.71) Dk Green 033271038
.63"-.87"
(1.60-2.21)
.75"-1.10 "
(1.90-2.79)
20,000
(88,960)
13" (33.02) 48" (121.92) .4 37" (1.11) .360" (.91) Red 033271039
.88"-1.12"
(2.24-2.84)
1.00"-1.50"
(2.54-3.81)
30,600
(136,109 )
15" (38.10 ) 60" (152.40) .500" (1.27) .500" (1.27) Dk Blue 033271040
1.13"-1.37"
(2.87-3.48)
1.25"-1.70"
(3.17-4.32)
46,800
(208,166)
18" (45.72) 76" (193.04) .625" (1.59) .625" (1.59) Yellow 033271041
1.38"-1.90"
(3.51-4.38)
1.50"-2.10"
(3.81-5.33)
66,500
(295,792)
24" (60.96) 89" (226.06) .750" (1.90) .750" (1.90) Aluminum 033271042
Note: E = Eye length. M = Mesh length at nominal diameter.
*For rope, select smallest size grip which meets required work load.
**Add to cable or rope diameter.
Kellems® Wire Management Products
Overhead Pulling Grips
Galvanized Steel
DUA-PULL® Grips, Flexible Eye, Double Weave Mesh
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead
transmission line stringing applications. They have a dual function, not provided by any
other grip, of working with both bare and insulated conductors
and synthetic rope.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
DUA-PULL® Feed Tube
For Use with
DUA- PULL Grip
Rope Diameter
Inches (cm)
Feed Tube Length
Inches (cm) Catalog Number
033271037 .25"-.65" (.63-1.65) 28" ( 71.12) 091061043
033271038 .50"-.90" (1.27-2.29) 40" (101.60) 091061044
033271039 .75"-1.10" (1.90-2.79) 52" (132.08) 091061045
033271040 1.00"-1.50" (2.54-3.81) 67" (170.18) 091061046
033271041 1.25"-1.70" (3.17-4.32) 83" (210.82) 091061047
033271042 1.50"-2.10" (3.81-5.33) 96" (243.84) 091061048
M
B
E
V-7www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Overhead Multiple Strength Pulling Grips
Flexible or Rotating Eye, Triple, Double, Single Weave, Galvanized Steel
Multiple Strength Style Grips
Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare
conductor, ground wires, messenger strands, wire rope and insulated cables.
Multiple Strength Grip-Rotating Eye
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm)
Rotating Eye Dia.
Inches (cm) Color Code Catalog Number
.25"-.49" (.63-1.24) 6,800 (30,246) 5" (12.70) 26" (66.04) ⁷⁄₈" (2.22) Dark Green 03302016
.50"-.74" (1.27-1.88) 10,000 (44,480) 6" (15.24) 32" (81.28) 1" (2.54) Brown 03302018
.75"-.99" (1.90-2.51) 14,400 (64,051) 6" (15.24) 41" (104.14) 1" (2.54) Light Blue 03302020
1.00"-1.24" (2.54-3.15) 24,600 (109,420) 8" (20.32) 52" (132.08) 1³⁄₈" (3.49) Gold 03302022
1.25"-1.49" (3.17-3.78) 30,600 (136,109) 8" (20.32) 56" (142.24) 1⁵⁄₈" (4.13) Black 03302024
1.50"-1.74" (3.81-4.42) 30,600 (136,109) 9" (22.86) 60" (152.40) 1⁷⁄₈" (4.76) Red 03302026
1.75"-2.24" (4.44-5.69) 48,000 (213,504) 10" (25.40) 70" (177.80) 1⁷⁄₈" (4.76) Dark Blue 03302028
2.00"-2.49" (5.08-6.32) 48,000 (213,504) 10" (25.40) 5 0 " (127.0 0 ) 1⁷⁄₈" (4.76) Yellow 03302066
2.50"-2.99" (6.35-7.59) 48,000 (213,504) 10" (25.40) 52" (132.08) 1⁷⁄₈" (4.76) Orange 03302097
3.00"-3.49" (7.62-8.86) 48,000 (213,504) 10" (25.40) 50 " (127.0 0) 1⁷⁄₈" (4.76) Aluminum 033021030
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 53" (134.62) 1⁷⁄₈" (4.76) Light Green 033021031
Note: E- Eye length M-Mesh length at nominal diameter.
Multiple Strength Grip-Flexible Eye
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm)
Eye A Dia.
Inches (cm) Color Code Catalog Number
.25"-.49" (.63-1.24) 6,800 (30,246) 9" (22.86) 26" (66.04) ¹⁄₄" (.63) Dark Green 03302044
.50"-.74" (1.27-1.88) 10,000 (44,480) 9" (22.86) 32" (81.28) ⁵⁄₁₆" (.79) Brown 03302046
.75"-.99" (1.90-2.51) 14,400 (64,051) 11" (27.94) 41" (104.14) ³⁄₈" (.95) Light Blue 03302048
1.00"-1.24" (2.54-3.15) 24,600 (109,420) 12" (30.48) 52" (132.08) ¹₂" (1.27) Gold 03302050
1.25"-1.49" (3.17-3.78) 30,600 (136,109) 12" (30.48) 56" (142.24) ¹₂" (1.27) Black 03302052
1.50"-1.74" (3.81-4.42) 30,600 (136,109) 12" (30.48) 60" (152.40) ¹₂" (1.27) Red 03302054
1.75"-2.24" (4.44-5.69) 48,000 (213,504) 18" (45.72) 70" (177.80) ⁵⁄₈" (1.59) Dark Blue 03302056
2.00"-2.49" (5.08-6.32) 48,000 (213,504) 18" (45.72) 5 0 " (127. 0 0 ) ⁵⁄₈" (1.59) Yellow 033021078
2.50"-2.99" (6.35-7.59) 48,000 (213,504) 18" (45.72) 52" (132.08) ⁵⁄₈" (1.59) Orange 033021079
3.00"-3.49" (7.62-8.86) 48,000 (213,504) 18" (45.72) 5 0 " (127.0 0 ) ⁵⁄₈" (1.59) Aluminum 033021080
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 18" (45.72) 53" (134.62) ⁵⁄₈" (1.59) Light Green 033021081
Note: E- Eye length. M-Mesh length at nominal diameter.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
ME
M
A
E
www.hubbell-wiring.comV-8 Wiring Device-Kellems
®
K-Type Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm)
Rotating Eye Dia.
Inches (cm) Catalog Number
Short
.50"-.62" (1.27-1.57) 5,600 (24,909) 5" (12.70) 11" (27.94) ⁷⁄₈" (2.22) 03301001
.63"-.74" (1.60-1.88) 6,800 (30,246) 5" (12.70) 11" (27.94) ⁷⁄₈" (2.22) 03301002
.75"-.99" (1.90-2.51) 6,800 (30,246) 6" (15.24) 20" (50.80) 1" (2.54) 03301013
1.00"-1.24" (2.54-3.15) 12,800 (56,934) 7 " (17.78 ) 20" (50.80) 1³⁄₈" (3.49) 03301014
1.25"-1.49" (3.17-3.78) 12,800 (56,934) 7 " (17.78 ) 21" (53.34) 1³⁄₈" (3.49) 03301016
1.50"-1.99" (3.81-5.05) 16,400 (72,941) 7 " (17.78 ) 25" (63.50) 1³⁄₈" (3.49) 03301017
2.00"-2.49" (5.08-6.32) 27,200 (120,986) 8" (20.32) 26" (66.04) 1⁵⁄₈" (4.13) 03301018
2.50"-2.99" (6.35-7.59) 33,000 (146,784) 10" (25.40) 28" (71.12) 1⁷⁄₈" (4.76) 03301019
3.00"-3.49" (7.62-8.86) 41,000 (182,368) 10" (25.40) 30" (76.20) 1⁷⁄₈" (4.76) 03301020
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 32" (81.28) 1⁷⁄₈" (4.76) 03301021
4.00"-4.49" (10.16-11.40) 48,000 (213,504) 10" (25.40) 33" (83.82) 1⁷⁄₈" (4.76) 033011017
Standard
.50"-.62" (1.27-1.57) 5,600 (24,909) 5" (12.70) 16" (40.64) ⁷⁄₈" (2.22) 03301011
.63"-.74" (1.60-1.88) 6,800 (30,246) 5" (12.70) 16" (40.64) ⁷⁄₈" (2.22) 03301012
.75"-.99" (1.90-2.51) 9,600 (42,701) 6" (15.24) 32" (81.28) 1" (2.54) 03301024
1.00"-1.49" (2.54-3.78) 16,400 (72,947) 7 " (17.78 ) 33" (83.82) 1³⁄₈" (3.49) 03301025
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 7 " (17.78 ) 34" (86.36) 1³⁄₈" (3.49) 03301026
2.00"-2.49" (5.08-6.32) 27,200 (120,986) 9" (22.86) 36" (91.44) 1⁵⁄₈" (4.13 ) 03301027
2.50"-2.99" (6.35-7.59) 33,000 (146,784) 10" (25.40) 38" (96.52) 1⁷⁄₈" (4.76) 03301028
3.00"-3.49" (7.62-8.86) 41,000 (182,368) 10" (25.40) 39" (99.06) 1⁷⁄₈" (4.76) 03301029
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 41" (104.14) 1⁷⁄₈" (4.76) 03301030
4.00"-4.49" (10.16-11.40) 48,000 (213,504) 10" (25.40) 42" (106.68) 1⁷⁄₈" (4.76) 03301031
4.50"-4.99" (11.43-12.67) 48,000 (213,504) 10" (25.40) 58" (147.32) 1⁷⁄₈" (4.76) 03301039
5.00"-5.99" (12.70-15.21) 40,000 (177,920) 10" (25.40) 60" (152.40) 1⁷⁄₈" (4.76) 03301047
6.00"-6.99" (15.24-17.75) 48,000 (213,504) 10" (25.40) 66" (167.64) 1⁷⁄₈" (4.76) 03301045
Note: E- Eye length. M-Mesh length at nominal diameter.
See page V-25 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Underground K-Type Pulling Grips
Rotating Eye, Double Weave, Galvanized Steel
K-Type Grips
Kellems® Rotating Eye, K-Type Pulling Grips are made of high strength galvanized steel
strand. All Grips feature double weave mesh for greater strength and added mesh contact
on the table, to handle longer or heavier pulling jobs. The forged eye mates easily with a
swivel or shackle.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
ME
V-9www.hubbell-wiring.com Wiring Device-Kellems
®
T-Type Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
Short
.50"-.62" (1.27-1.57) 4,500 (20,016) 8" (20.32) 21" (53.34) 033041082
.63"-.74" (1.60-1.88) 5,600 (24,909) 8" (20.32) 24" (60.96) 033041083
.75"-.99" (1.90-2.51) 6,800 (30,246) 9" (22.86) 24" (60.96) 033041084
1.00"-1.49" (2.54-3.78) 9,600 (42,701) 9" (22.86) 24" (60.96) 033041085
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 11" (27.94) 24" (60.96) 033041086
2.00"-2.49" (5.08-6.32) 18,500 (82,288) 12" (30.48) 24" (60.96) 033041087
2.50"-2.99" (6.35-7.59) 24,500 (108,976) 12" (30.48) 24" (60.96) 033041088
3.00"-3.49" (7.62-8.86) 24,500 (108,976) 14" (35.56) 24" (60.96) 033041089
3.50"-3.99" (8.89-10.13) 31,000 (137,888) 14" (35.56) 26" (66.04) 033041090
Standard
.75"-.99" (1.90-2.51) 6,800 (30,246) 9" (22.86) 36" (91.44) 033041091
1.00"-1.49" (2.54-3.78) 9,600 (42,701) 9" (22.86) 36" (91.44) 033041092
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 11" (27.94) 36" (91.44) 033041093
2.00"-2.49" (5.08-6.32) 18,500 (82,288) 12" (30.48) 36" (91.44) 033041094
2.50"-2.99" (6.35-7.59) 24,500 (108,976) 12" (30.48) 36" (91.44) 033041095
3.00"-3.49" (7.62-8.86) 24,500 (108,976) 14" (35.56) 36" (91.44) 033041096
3.50"-3.99" (8.89-10.13) 31,000 (137,888) 14" (35.56) 40" (101.60) 033041097
Note: E- Eye length. M-Mesh length at nominal diameter.
See page V-25 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Underground T-Type Pulling Grips
Flexible Eye, Double Weave, Galvanized Steel
T-Type Grips
Kellems® Flexible T-Type Pulling Grips are made of high strength galvanized steel strand.
They feature double weave mesh for positive holding power in medium to heavy pulling
jobs. The grip eye will easily attach to a swivel.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
ME
www.hubbell-wiring.comV-10 Wiring Device-Kellems
®
Slack Grip-Closed Mesh, Offset Eye, Double Weave, Galvanized Steel
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
Standard
.75"-.99" (1.90-2.51) 2,6 0 0 (11,56 5) 7 " (17.78 ) 12" (30.48) 03308003
1.00"-1.24" (2.54-3.15) 4,000 (17,792) 8" (20.32) 15" (38.10 ) 03308004
1.25"-1.49" (3.17-3.78) 5,400 (24,019) 8" (20.32) 16" (40.64) 03308005
1.50"-1.74" (3.81-4.42) 6,600 (29,357) 8" (20.32) 20" (50.80) 03308006
1.75"-1.99" (4.44-5.05) 10,000 (44,480) 10" (25.40) 18" (45.72) 03308007
2.00"-2.49" (5.08-6.32) 11,000 (48,928) 10" (25.40) 19" (48.26) 03308008
2.50"-2.99" (6.35-7.59) 11,000 (48,928) 10" (25.40) 20" (50.80) 03308009
3.00"-3.49" (7.62-8.86) 14,500 (64,496) 12" (30.48) 21" (53.34) 03308010
3.50"-3.99" (8.89-10.13) 14,500 (64,496) 12" (30.48) 22" (55.88) 03308011
Note: E- Eye length. M-Mesh length at nominal diameter.
See page V-25 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Special Purpose Pulling Grips
Non-Conductive and Slack Pulling
Non-Conductive Grips
Kellems® Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid
fiber, are available for pulling single cable or cable bundles. Their braided double weave
design adds strength and positive holding power.
Non-Conductive Grips, Single Eye, Double Weave, Non-Metallic
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm)
A
Inches (cm) Color Code Catalog Number
.50"-.62" (1.27-1.57) 4,000 (17,792) 5.5" (13.97) 24" (60.96) .44" (1.12) Green 03628001
.63"-.74" (1.60-1.88) 5,000 (22,240) 5.5" (13.97) 26" (66.04) .4 4" (1.12) Yellow 03628002
.75"-.99" (1.90-2.51) 6,000 (26,688) 6.0" (15.24) 31" (78.74) .63" (1.60) Red 03628003
1.00"-1.24" (2.54-3.15) 6,000 (26,688) 6.5" (16.51) 36" (91.44) .63" (1.60) Blue 03628004
1.25"-1.49" (3.17-3.78) 6,000 (26,688) 6.7" (17.02) 41.5" (105.41) .63" (1.60) White 03628005
1.50"-1.99" (3.815.05) 6,000 (26,688) 8.0" (20.32) 44.0" (121.76) .63" (1.60) Pink 03628006
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
Slack Pulling Grips
Slack Pulling Grips are offered in three styles made of galvanized steel. The closed
type is used when the cable end is accessible. When not accessible, there are
split lace and split rod closing styles. All grips feature a single offset eye for easy
attachment to a pulling line.
ME
M E
A
V-11www.hubbell-wiring.com Wiring Device-Kellems
®
Slack Grip-Split Mesh, Rawhide Lace Closing, Offset Eye, Double Weave, Galvanized Steel
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
Standard
.75"-.99" (1.90-2.51) 2,500 (11,120) 7 " (17.78 ) 12" (30.48) 03309003
1.00"-1.24" (2.54-3.15) 3,500 (15,568) 8" (20.32) 15" (38.10 ) 03309004
1.25"-1.49" (3.17-3.78) 4,000 (17,792) 8" (20.32) 16" (40.64) 03309005
1.50"-1.74" (3.81-4.42) 4,000 (17,792) 9" (22.86) 17" (43.18) 03309006
1.75"-1.99" (4.44-5.05) 4,000 (17,792) 10" (25.40) 18" (45.72) 03309007
2.00"-2.49" (5.08-6.32) 4,000 (17,792) 10" (25.40) 19" (48.26) 03309008
2.50"-2.99" (6.35-7.59) 4,000 (17,792) 10" (25.40) 20" (50.80) 03309009
Long
1.50"-1.99" (3.81-5.05) 4,000 (17,792) 9" (22.86) 25" (63.50) 03309015
2.00"-2.49" (5.08-6.32) 4,000 (17,792) 10" (25.40) 26" (66.04) 03309016
2.50"-2.99" (6.35-7.59) 4,000 (17,792) 10" (25.40) 29" (73.66) 03309017
3.00"-3.49" (7.62-8.86) 4,000 (17,792) 12" (30.48) 32" (81.28) 03309018
3.50"-3.99" (8.89-10.13) 4,000 (17,792) 12" (30.48) 35" (88.90) 03309019
Kellems® Wire Management Products
Special Purpose Pulling Grips
Slack Pulling
Slack Pulling Grips
Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is
used when the cable end is accessible. When not accessible, there are split lace and split
rod closing styles. All grips feature a single offset eye for easy attachment to a pulling line.
Slack Grip-Split Mesh, Rod Closing, Offset Eye, Single Weave, Galvanized Steel
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
.50"-.61" (1.27-1.55) 1,500 (6,672) 7 " (17.78 ) 6" (15.24) 03310001
.62"-.74" (1.57-1.88) 1,800 (8,006) 7 " (17.78 ) 8" (20.32) 03310002
.75"-.99" (1.90-2.51) 2,200 (9,786) 7 " (17.78 ) 10" (25.40) 03310003
1.00"-1.24" (2.54-3.15) 3,400 (15,123) 8" (20.32) 12" (30.48) 03310004
1.25"-1.49" (3.17-3.78) 4,500 (20,016) 8" (20.32) 14" (35.56) 03310005
1.50"-1.74" (3.81-4.42) 5,800 (25,798) 9" (22.86) 15" (3 8.10 ) 03310006
1.75" -1.99" (4.44-5.05) 7,600 (33,805) 10" (25.40) 16" (40.64) 03310007
2.00"-2.49" (5.08-6.32) 9,000 (40,032) 10" (25.40) 19" (48.26) 03310008
2.50"-2.99" (6.35-7.59) 11,000 (48,928) 10" (25.40) 20" (50.80) 03310009
3.00"-3.49" (7.62-8.86) 12,000 (53,376) 12" (30.48) 21" (53.34) 03310010
3.50"-3.99" (8.89-10.13) 12,000 (53,376) 12" (30.48) 24" (60.96) 03 310011
Note: E- Eye length. M-Mesh length at nominal diameter.
See page V-25 for multiple cables in a single pulling grip.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
ME
ME
www.hubbell-wiring.comV-12 Wiring Device-Kellems
®
Kellems® Wire Management Products
Low Tension Pulling Grips
Flexible Eye, Single Weave, Galvanized Steel
Light Duty Grips
Light Duty Grips are made of galvanized steel in a single weave construction.
They feature a flexible eye for easy attachment to a pulling line.
Junior Pulling Grips
Junior Pulling Grips feature a strong galvanized steel, single weave mesh.
A flexible eye easily attaches to a pulling line, snake or fish tape.
Junior Pulling Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Model Catalog Number
.19"-.24" (.48-.61) 400 (1,779) 3¹⁄₄" (8.25) 4¹⁄₄" (10.79) J19 03305011*
.25"-.37" (.63-.94) 450 (2,002) 3¹⁄₄" (8.25) 4¹⁄₄" (10.79) J25 03305001
.38"-.49" (.97-1.24) 900 (4,003) 3³⁄₄" (9.52) 7" (17.7 8) J37 03305002
.50"-.62" (1.27-1.57) 1,300 (5,782) 4¹⁄₄" (10.79) 8¹⁄₂" (21.59) J50 03305003
.63"-.74" (1.60-1.88) 1,9 50 (8 ,674) 5" (12.70) 10" (25.40) J62 03305004
.75"-.99" (1.90-2.51) 2,800 (12,454) 5³⁄₄" (14.60) 10" (25.40) J75 03305005
1.00"-1.24" (2.54-3.15) 3,900 (17,347) 6¹⁄₂" (16.51) 11¹ ⁄ ₂ " (29.21) J100 03305006
Junior Grip Kit contains 6 grips, one of each size above, except 03305011. 03 3051114
Note: E- Eye length. M-Mesh length at nominal diameter.
*Not included in Junior Grip Kit, 033051114.
Note: See page V-25 for multiple cables in a single pulling grip.
See page V-26 for building wire selection chart.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
M E
M E
033051114
Light Duty Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
Short
.50"-.62" (1.27-1.57) 2,800 (12,454) 5" (12.70) 11" ( 27. 9 4) 03303001
.63"-.74" (1.60-1.88) 2,800 (12,454) 5" (12.70) 11" (27.94) 03303002
.75"-.99" (1.90-2.51) 4,000 (17,792) 6" (15.24) 12" (30.48) 03303003
1.00"-1.24" (2.54-3.15) 5,300 (23,574) 7 " (17.78 ) 13" (33.02) 03303004
1.25"-1.49" (3.17-3.78) 5,300 (23,574) 7 " (17.78 ) 14" (35.56) 03303005
1.50"-1.74" (3.81-4.42) 6,800 (30,246) 8" (20.32) 15" (38 .10) 03303006
1.75"-1.99" (4.44-5.05) 8,500 (37,808) 9" (22.86) 17" (43.18) 03303007
2.00"-2.49" (5.08-6.32) 8,500 (37,808) 9" (22.86) 18" (45.72) 03303008
Standard
.50"-.62" (1.27-1.57) 2,800 (12,454) 5" (12.70) 16" (40.64) 03303010
.63"-.74" (1.60-1.88) 2,800 (12,454) 5" (12.70) 16" (40.64) 03303011
.75"-.99" (1.90-2.51) 4,000 (17,792) 6" (15.24) 20" (50.80) 03303012
1.00"-1.24" (2.54-3.15) 6,800 (30,246) 7 " (17.78) 20" (50.80) 03303013
1.25"-1.49" (3.17-3.78) 6,800 (30,246) 7 " (17.78 ) 21" (53.34) 03303015
1.50"-1.99" (3.81-5.05) 6,800 (30,246) 8" (20.32) 23" (58.42) 03303016
2.00"-2.49" (5.08-6.32) 8,500 (37,808) 9" (22.86) 25" (63.50) 03303017
2.50"-2.99" (6.35-7.59) 10,600 (47,149) 9" (22.86) 27" (68.58) 03303018
3.00"-3.49" (7.62-8.86) 14,700 (65,386) 10" (25.40) 30" (76.20) 03303019
3.50"-3.99" (8.89-10.13) 14,700 (65,386) 10" (25.40) 32" (81.28) 03303029
V-13www.hubbell-wiring.com Wiring Device-Kellems
®
Regular Wire Rope Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
Approx. Strength
of Grip Feet (m) Catalog Number
⁹⁄₁₆"- ⁵⁄₈" (1.43-1.59) 7,500 (33,360) 5.75 (1.75) 03316001
³⁄₄"- ⁷⁄₈" (1.90 -2.22) 12,500 (55,600) 6.75 (1.90) 03316002
1"-1¹⁄₈" (2.54-2.86) 16,000 (71,168) 7.0 0 (2.13 ) 03316003
1¹⁄₄"- 1³⁄₈" (3.17-3.49) 20,000 (88,960) 8.00 (2.44) 03316004
1³⁄₈"- 1¹⁄₂" (3.49-3.81) 20,000 (88,960) 8.00 (2.44) 03316006
Kellems® Wire Management Products
Wire Rope Splicing Grips
Triple, Double, Single Weave, Galvanized Steel
Kellems® Wire Rope Grips
Wire Rope Grips are made of high strength galvanized steel strand in a construction
of triple, double and single weave for superior gripping ability. They are available with
or without a rotating barrel which will help eliminate twist in the old rope from being
transferred to the new rope.
Rotating Wire Rope Grips
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
Approx. Strength
of Grip Feet (m)
Barrel Dimensions
Length. x O.D. In. (cm) Catalog Number
⁷⁄₁₆"- ¹⁄₂" (1.11-1.27) 5,000 (22,240) 5.33 (1.63) 3.00" (7.62) x .87" (2.21) 03317001
⁹⁄₁₆"- ⁵⁄₈" (1.43-1.59) 7,500 (33,360) 5.83 (1.78) 4.25" (10.79) x 1.00" (2.54) 03317002
³⁄₄"- ⁷⁄₈" (1.90 -2.22) 12,500 (55,600) 6.50 (1.98) 4.25" (10.79) x 1.00" (2.54) 03317003
1"- 1¹⁄₈" (2.54-2.86) 16,000 (71,168) 8.67 (2.64) 5.50" (13.97) x 1.37" (3.48) 03317004
1¹⁄₄"- 1³⁄₈" (3.17-3.49) 20,000 (88,960) 9.0 0 (2.74) 5.50" (13.97) x 1.37" (3.48) 03317005
1¹⁄₂"- 1³⁄₄" (3.81-4.44) 20,000 (88,960) 11.00 (3.35) 5.50" (13.97) x 1.37" (3.48) 03317006
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
www.hubbell-wiring.comV-14 Wiring Device-Kellems
®
Double Weave Tube
Cable Diameter Range
Inches (cm)
.37"-.49"
(.94-1.24)
.50"-.61"
(1.27-1.55)
.62"-.74"
(1.57-1.88)
.75"-.99"
(1.90-2.51)
1.00"-1.49"
(2.54-3.78)
Approx. Breaking
Strength Lbs. (N)
3,500
(15,568)
3,500
(15,568)
4,400
(19,571)
7, 50 0
(33,360)
10,000
(44,480)
Mesh Length
Inches (cm) Catalog Number
18" (45.72) 013041330 01304064 01304009 — —
24" (60.96) — 01304011 01304013 01304010 01304015
36" (91.44) — — 013041234 01304054 01304055
48" (121.92) — — — 01304017 01304029
72" (182.88) — — — 01304037 013041333
Kellems® Wire Management Products
Cable Splicing Grips
Double Weave, Galvanized Steel / Single Weave, Galvanized Steel
Splicing Grips
Splicing Grips are made of galvanized steel in double weave mesh construction.
They are available in various lengths and sizes to suit most applications.
Junior Splicing Grips, Single Weave
Junior Splicing Grips are made of galvanized steel and are designed for use in very light
duty and small splicing jobs.
Junior Tube
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
Length @ Nom
Diameter Inches (cm) Catalog Number
.18"-.24" (.46-.61) 400 (1,779) 7 " (17.78 ) 01301008
.25"-.36" (.63-.91) 400 (1,779) 8" (20.32) 01301013
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
V-15www.hubbell-wiring.com Wiring Device-Kellems
®
Punch-Lok® Bands
Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose.
Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope.
When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release caused by tripping
on obstructions. A conductor-to-conductor (double-socking) pulling operation is a good example: where two grips connect
two conductors to form a temporary splice. Bands should be applied to the ends of the grips as illustrated herein. It is also
common practice to tape over the banded tail area to assure smooth passage through the sheaves.
The conductor should be installed in the grip up to the elbows of the aluminum shoulders in order to assure full and complete
gripping action as illustrated above.
Punch-Lok® Bands
Grip Banding Range
Inches (cm)
Band Width
Inches (cm)
Band Inside Diameter
Inches (cm) Model Catalog Number
¹⁄₄"-1¹⁄₈" (.63-2.86) ³⁄₈" (.95) 1³⁄₈" (3.49) 0 - 311 20320050
1¹⁄₈"-1⁵⁄₈" (2.86-4.13) ³⁄₈" (.95) 2" (5.08) 0-316 20320051
1⁵⁄₈"-2¹⁄₄" (4.13-5.71) ⁵⁄₈" (1.59) 2¹⁄₂" (6.35) 0 -10 20320052
2¹⁄₄"-3¹⁄₂" (5.71-8.89) ⁵⁄₈" (1.59) 4" (10.16 ) 0-16 20320053
3¹⁄₂"-5" (8.89-12.70) ⁵⁄₈" (1.59) 6" (15.24) 0-24 20320054
Accessories
Punch-Lok Tools Catalog Number
P-1000 for use with ⁵⁄₈" width Banding tool. 20320048
P-38 for use with ³⁄₈" and ⁵⁄₈" width Banding tool for tight spaces. 20320047
Note: In all cases two Punch-Lok Bands should be double wrapped approximately one inch to two inches (2.54cm to 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release.
Kellems® Wire Management Products
Tools and Bands
Pulling Grips Accessories
Punch-Lok® is a registered trademark of Punch-Lok Inc.
20320054
20320048
20320047
www.hubbell-wiring.comV-16 Wiring Device-Kellems
®
C
B
A
F
E
G
D
20308001A
Stainless Steel Swivels
Maximum Safe
Working Load
Lbs. (N)
Dimensions in Inches (cm)
Model Catalog NumberA B C D E F G
2,250
(10,000)
⁷⁄₈"
(2.22)
2½"
(6.35)
3³⁄₈"
(8.57)
⁷⁄₁₆"
(1.11)
³⁄₈"
(0.95)
⁵⁄₁₆"
(0.79)
³¹⁄₃₂"
(2.46)
A-13L 20308001A
5,000
(22,240)
1¼"
(3 .17 )
3¹¹⁄₁₆"
(9.37)
4¾"
(12.06)
1⁷⁄ ₃ ₂"
(1.35)
1⁷⁄ ₃ ₂"
(1.35)
¹³⁄₃₂"
(1.03)
1⁹⁄₃₂"
(3.25)
BB -13L 20308002A
9,000
(40,030)
1½"
(3.81)
4¼"
(10.79)
5⁵⁄₈"
(14.29)
¹¹⁄₁₆"
(1.75)
1⁹⁄₃₂"
(1.51)
½"
(1.27)
1⁹⁄₁₆"
(3.97)
B-13L 20308003A
10,000
(44,480)
1⁵⁄₈"
(4.13)
4½"
(11.43)
6"
(15.24)
¾"
(1.90)
¹¹⁄₁₆"
(1.75)
⁵⁄₈"
(1.59)
1²³⁄₃₂"
(4.36)
C-13L 20308004A
30,000
(133,440)
2³⁄₈"
(6.03)
7⁵⁄₈"
(19.37)
10"
(25.40)
1³⁄₁₆"
(3.02)
1¹⁄₃ ₂"
(2.62)
⁷⁄₈"
(2.22)
2²⁵⁄₃₂"
( 7. 0 6 )
D-13L 20308005A
Kellems® Wire Management Products
Swivels
Pulling Grips Accessories
Stainless Steel Swivels
Swivels are essential to the efficiency and safety of any high tension application. They are
particularly important where continuous pulls develop higher and higher torque levels.
Torque is intensified by the pull-resistance of the cable itself and the resistance of the high
tension controlling equipment regulating line sag.
Ball bearing swivels release torque and prevent it from reaching dangerous levels that can
damage the cable and obstruct the lines.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-17 to V-26.
V-17www.hubbell-wiring.com Wiring Device-Kellems
®
Pulling Grip Selection Chart
Grip Style Application Page Number
DUA-PULL®, flexible eye Extra high strength overhead transmission line stringing for bare or
insulated conductor and synthetic rope.
V-6
Multiple strength, flexible eye Normal overhead transmission and distribution line stringing for bare or
insulated conductor.
V-7
Multiple strength, rotating eye Normal overhead transmission and distribution line stringing for bare or
insulated conductor.
V-7
K-type grip, rotating eye Underground power cables and communication lines. Service lines into factories. V-8
T-type grip, flexible eye Underground power cables and communication lines. Service lines into factories. V-9
Non-conductive, flexible eye Pull insulated distribution cable into place. V-10
Slack pulling, closed mesh Remove underground cable. For pulling slack in final placement of new cable
when end of cable is available.
V-10
Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable
rawhide lace closing when end of cable is not available.
V-11
Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable
rod closing when end of cable is not available, with rod closing for quick installation.
V-11
Light duty, flexible eye Light pulling, underground electrical construction. Industrial plant
wiring and rewiring jobs.
V-12
Junior, flexible eye Connect bundled insulated building wire to a pulling tape. Pull wire through conduit. V-12
Regular and rotating wire rope Restring wire rope in cranes and oil rigs. V-13
Splicing Temporary splice for cable or wire rope. V-14
Pulling Grip Accessories Tools, bands, swivels. V-15, V-16
Fiber Optic Cable Pulling Grips Pull fiber optic cable into place overhead, underground or through duct and conduit. V-47, V-48, V-49
Kellems® Wire Management Products
Technical Information
Pulling Grips
Kellems Pulling Grips are reusable tools for pulling electrical cable, bare conductor or rope. They are easy and fast to install,
providing the user with a smooth, slim profile that allows for easy passage through ducts and conduit. Kellems Pulling Grips
are made of the highest quality galvanized steel strand which assures the user of a long lasting grip. There is a Kellems Pulling
Grip for every pulling job.
1. Pulling grips are to be installed by a qualified individual in accordance with all applicable national and local safety,
electrical and rigging codes.
2. Ensure that the correct grip is selected for your specific needs.
3. Do not use a pulling grip for any application other than pulling cable.
4. Thoroughly examine the grip for damage. Do not use a damaged grip.
5. Ensure that the recommended work load of the grip is suitable for the application. Never use grips at their
approximated rated breaking strength. A safety factor of 5 is recommended for pulling grips.
6. Do not alter grips in any way. For example, do not modify pulling eyes, shoulders, fittings or lugs.
7. Do not attach any type of pulling hardware to any point on the grip other than the pulling eye. The pulling eye is
the only acceptable means of attachment to external hardware.
8. Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against accidental release
of the grip. Accidental release can occur if an object contracts and pushes against the tail end of the mesh,
thereby expanding and releasing its hold.
Select The Correct Pulling Grip
Each Kellems Grip is designed to work on a specific range of cable diameters.
Step 1 Refer to the chart below to determine the style of grip best suited for your application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your cable diameter.
Step 4 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed
approximate breaking strength of the grip to insure that the grip will be strong enough. Refer to page V-18 for
safety and working load factors.
CAUTION: It is very important to comply with all of the following precautions. Failure to do so may result in property damage,
personal injury or death.
www.hubbell-wiring.comV-18 Wiring Device-Kellems
®
The broad application of Kellems grips on a wide variety of
objects requires that adequate safety factors be used to
establish working loads. The approximate breaking strength
of a Kellems grip represents an average calculation based on
data established from actual direct tension testing done in
our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are never
the same. The tension, diameter, movement, number of
objects gripped, gripping surface, and the attachments used
are just some of the factors which vary with each application.
These factors, together with the effects of abrasion,
corrosion, prior use or abuse and any other variables of a
specific application, must be considered by the user and
the grip replaced as appropriate. Where the conditions of
the application are not well defined or known, or where risk
of injury to persons or property is involved, a greater safety
factor should be utilized.
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling grips,
and ten for catalog listed support grips.
Any warranty as to quality, performance or fitness for
use of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored, handled,
used, maintained and inspected by the user at a frequency
appropriate for the use and condition of the grip.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Safety And Working Load Factors For Wire Mesh Grips
Examples
Approx. Breaking Safety Max. Recommended
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number
Pulling Grips 27,200 (120,986) 5 5,4 40 (24,197 ) 03301027
Support Grips 1,610 (7,161) 10 161 (716) 02201018
The maximum recommended working load then is the tension to be exerted on the grip in application with a margin of safety
to take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable for the application.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric unit
of weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Pulling Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Pulling grips
• Not subject to continuous • Wire rope grips
outside environment • Splicing grips
Non-metallic strand • Superior flex life • Non-conductive pulling grips
• Non-conductive
• Corrosion resistant
• Moderate strength
Approvals
UL and CSA Certification is indicated on appropriate product catalog pages.
V-19www.hubbell-wiring.com Wiring Device-Kellems
®
Overhead Pulling DUA-PULL® Grips
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission line stringing
applications. They have a dual function of working with both bare and insulated conductors and synthetic rope, not provided
by any other grip. Kellems’ patented two-over, two-under weave design gives exceptional strength and gripping ability by
putting more steel mesh in contact with the cable or rope surfaces.
THIS IS THE ONLY PULLING GRIP RECOMMENDED FOR USE ON SYNTHETIC ROPE.
Application
The DUA-PULL Grips are primarily used in overhead transmission line construction where loads and safety considerations
require an extra high strength grip. They are most commonly used for attaching pulling lines to conductors, conductors to
running boards and “double socking" for conductor-to-conductor connections. The DUA-PULL line accommodates ACSR,
ACAR, all aluminum and copper conductors. Also, the grips accommodate ground wires, messenger strands, wire ropes
and synthetic ropes.
Benefits
• Made of high strength galvanized steel strand.
• Recommended for pulling bare or insulated conductor, wire rope and synthetic rope.
• DUA-PULL mesh design offers the greatest holding power for all pulling applications.
• Each grip size is color coded for fast and accurate identification and selection.
• Will mate with swivels. See page V-16.
Feed Tubes
The Kellems Feed Tube is used when assembling synthetic rope into the DUA-PULL Grip. It is required on the largest two
sizes of DUA-PULL Grips. Feed Tubes are available for use on all size DUA-PULL Grips.
Benefits
• Saves time, allowing fast, easy assembly.
• Can be reused if not damaged.
Note: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release. See page V-15.
3. Double braided rope, such as 2-in-1 type, should be back spliced for approximately 2/3 of the mesh length for best gripping results.
Grip size should be selected by diameter of back splice.
Components
Kellems® Wire Management Products
Technical Information
Pulling Grips
Identification Sleeve
Color Coded
EyeEnd of Conductor
or Rope
Tail
Bands
Mesh
Shoulder Protector
www.hubbell-wiring.comV-20 Wiring Device-Kellems
®
Overhead Pulling Multiple Strength Grips
Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires, messenger
strands, wire rope and insulated cables. They are made of high strength galvanized steel strand and feature a multi-weave
mesh construction of single, double and triple weave for firm holding power.
Application
Kellems Multiple Strength Grips are ideal for overhead transmission and distribution line stringing where moderate loading
is anticipated. They are economical tools for attaching conductors to pulling lines and double socking for conductor-to-
conductor connections.
Rotating Eye Feature
Multiple Strength Grips are available with a forged steel rotating eye which can be attached to a swivel. The forged eye is
durable, compact and streamlined and will thread through blocks and sheaves without binding. The rotating eye is not a swivel
and will not turn while under tension; it can turn to relieve pulling torque when tension is relaxed. If constant swivel action is
required, a swivel should be used. For swivel dimensions, see page V-16. For rotating eye dimensions, see page V-21.
Flexible Eye Feature
Multiple Strength Grips are also available with a flexible, patented wire rope eye. This compact eye will mate with a swivel,
and pass through blocks and sheaves without binding.
Benefits
• Economical, high strength pulling tool.
• Multi-weave construction provides greater strength and holding power.
• Endless Weave Grip end lies flat on the cable and will not snag.
Note: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release. See page V-15.
Components
Kellems® Wire Management Products
Technical Information
Pulling Grips
Forged Eye
Flexible Eye
(Patented)
End of Conductor
or Cable
Tail
Bands
(Double Wrapped)
Mesh
Shoulder Protectors
Color Coded
V-21www.hubbell-wiring.com Wiring Device-Kellems
®
Underground Pulling K-Type and T-Type Grips
K-Type Application
Rotating Eye, K-Type Pulling Grips are specially designed for use in the installation of underground power cables,
communication lines and service lines into factories, shopping centers, construction projects and general underground
electrical construction.
Rotating Eye Feature
K-Type Grips come equipped with a forged steel rotating eye which can be attached to a swivel. The forged eye is durable,
compact and streamlined, and will thread through blocks and sheaves without binding.
The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when the
tension is relaxed. If constant swivel action is required, a swivel should be used. For swivel dimensions, see page V-16.
Benefits
• An economical tool for pulling cable.
• Safe, rugged and dependable.
• Equipped with a rotating eye for spin out of pulling torque after load release.
• Easily installed and removed.
Rotating Eye Dimensions
Rotating Eye
Dimensions
Inches (cm) A B C D F
⁷⁄₈" (2.22) ⁷⁄₈" (2.22) ⁹⁄₃₂" (.71) ¹⁄₂" (1.27) ⁷⁄₈" (2.22) 2⁵⁄₈" (6.67)
1" (2.54) 1" (2.54) ¹⁄₂" (1.27) ⁹⁄₁₆" (1.43) ¹³⁄₁₆" (2.06) 3¹⁄₂" (8.89)
1³⁄₈" (3.49) 1³⁄₈" (3.49) ¹⁄₂" (1.27) ¹¹⁄₁₆" (1.75) 1" (2.54) 4¹⁄₂" (11.43)
1⁵⁄₈" (4.13) 1⁵⁄₈" (4.13) ⁵⁄₈" (1.59) ⁷⁄₈" (2.22) 1³⁄₁₆" (3.02) 5⁵⁄₁₆" (13.49)
1⁷⁄₈" (4.76) 1⁷⁄₈" (4.76) ²¹⁄₃₂"(1.67) 1" (2.54) 1³⁄₈" (3.49) 6¹⁄₈" (15.56)
T-Type
Kellems Flexible T-Type Pulling Grips are made of high strength galvanized steel strand. They feature double weave mesh for
positive holding power in medium to heavy pulling jobs. The grip eye will easily attach to a swivel.
Application
T-Type Pulling Grips are used for the installation of underground power cables, communication lines and service lines into
factories, construction projects and for general underground electrical construction. Available in two mesh lengths, short for
medium pulls, and standard for general purpose pulling.
Benefits
• Will pull a single cable or cable bundles.
• Patented flexible eye design provides flexibility to follow line of pull.
• A dependable, reusable pulling tool.
• Easily installed and removed.
• Mates easily with a swivel. See page V-16.
Kellems® Wire Management Products
Technical Information
Pulling Grips
F
D
A
3/16 R.
1/8 R.
C
B
www.hubbell-wiring.comV-22 Wiring Device-Kellems
®
Special Purpose Grips
Non-Conductive Pulling Grips
Kellems Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available for pulling single
cable or cable bundles. Their braided double weave design adds strength and positive holding power.
Application
Kellems Non-Conductive Pulling Grips were developed for use by utilities for pulling overhead distribution lines in close
proximity to energized lines and hardware.
Benefits
• Color coded for fast on-site selection.
• Extra flexibility for easy installation.
• Non-metallic mesh provides for safe pulls over “hot" areas.
• Pellethane jacketed aramid fiber mesh resists abrasion.
• Grips are corrosion resistant.
Note: Taping is required to guard against accidental release and to insure maximum reliability. Apply vinyl plastic electrical tape starting 2" to 3" (5.08cm to
7.62cm) from the tail of the grip onto 2" to 3" (5.08cm to 7.62cm) of cable.
Slack Pulling Grips
Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is used when the cable end is
accessible. When not, there are split lace and split rod closing styles. All grips feature single offset eye for easy attachment to
a pulling line.
Application
Slack Grips are widely used in pulling slack for final placement of under ground cable after it has been pulled in. They are also
used for removing cable. Standard mesh lengths are generally used in restricted space for short pulls. Longer lengths are
used for higher pulling loads where space is not restricted.
Benefits
• Easy attachment to pulling lines.
• Reusable rawhide lace for lace closure.
• Galvanized steel for strength.
Note: 1. Replacement rawhide lace. Catalog number 20920002.
2. See page V-43 for lace and rod closing instructions.
Kellems® Wire Management Products
Technical Information
Pulling Grips
V-23www.hubbell-wiring.com Wiring Device-Kellems
®
Commercial Construction/Light Duty Grips
Light Duty Pulling Grips
Light Duty Pulling Grips are made of galvanized steel in a single weave construction. They feature a flexible eye for easy
attachment to a pulling line.
Application
Light Duty Grips are used in general underground electrical construction where pulling tensions are low.
They are easy tools to use in wiring industrial plants and commercial buildings.
Benefits
• Perfect tools for light pulling jobs.
• Installs easily on cable.
• Strong, galvanized steel construction.
Junior Duty Pulling Grips
Junior Pulling Grips feature a strong galvanized steel, single weave mesh. A flexible eye easily attaches to a pulling line,
snake or fish tape.
Application
Designed to pull building wire, Junior grips are safe tools to use in pulling wire at low tension through conduit during
electrical construction.
Benefits
• Installs easily over building wire.
• Strong secure grip.
• Reusable.
• Pulls single cable or cable bundles.
Junior Grip Kit
Junior Grip Kit contains 6 grips, one of each size. Catalog number 033051114. See page V-12.
Note: See page V-26 for building wire selection chart.
Kellems® Wire Management Products
Technical Information
Pulling Grips
www.hubbell-wiring.comV-24 Wiring Device-Kellems
®
Splicing Grips
Wire Rope Splicing
Kellems Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double and single
weave for superior gripping ability. They are available with or without a rotating barrel which will help eliminate twist in
the old rope from being transferred to the new rope.
Application
Wire Rope Grips are used for changing wire rope on oil derricks, large cranes, overhead cranes and drag lines. It provides
a quick, safe, inexpensive temporary splice. By installing the used wire rope in one end and the new rope in the other,
the new wire rope can be pulled in as the old one is pulled out.
Benefits
• High strength for secure pulling.
• Easy installation.
• Flexible to pass through sheaves and blocks.
Note: 1. During installation each end of the grip should be banded and taped down securely over the rope to insure smooth passage through sheaves and to guard
against accidental release. See page V-15 for end bands.
2. The rotating barrel is not a swivel and will not turn while under tension. It can turn to relieve pulling torque when tension is relaxed.
Cable Splicing
Splicing Grips are made of galvanized steel in double or single weave mesh construction. They are available in various
lengths and sizes to suit most applications.
Application
Splicing Grips are used as a temporary splice for rope, cable or wire rope. They can also be used as cable reinforcement,
and can act as a shield to protect cables and hoses from abrasion.
Benefits
• Easily installed or removed.
• Galvanized steel construction for strength.
• Flexible to follow cable path.
Note: 1. During installation, each end of the splicing grip should be banded and taped down securely to the cable to insure smooth passage with the cable and guard
against accidental release.
2. See page V-15 for end bands.
Kellems® Wire Management Products
Technical Information
Splicing Grips
V-25www.hubbell-wiring.com Wiring Device-Kellems
®
Number of Cables in One Grip
23456 and 7 8 9
Grip Dia.Range
Inches (cm)
.30-.38
(.76-.97)
.25-.31
(.63-.79)
.22-.27
(.56-.69)
.19 -.24
(.48-.60)
.17-.22
(.43-.56)
.15-.19
(.38-.48)
.14 -.18
(.36-.46)
.50-.61
(1.27-1.55)
.38-.44
(.97-1.12)
.31-.36
(.79-.91)
.27-.31
(.69-.79)
.24-.29
(.61-.74)
.22-.26
(.56-.66)
.19 -.2 3
(.48-.58)
.18-. 21
(.46-.53)
.62-.74
(1.57-1.88)
.44-.59
(1.12-1.50)
.36-.49
(.91-1.24)
.31-.42
(.79-1.07)
.29-.38
(.74-.97)
.26-.34
(.66-.86)
.23-.31
(.58-.79)
.21-.28
(.53-.71)
.75-.99
(1.90-2.51)
.59-.75
(1.50 -1.90)
.49-.63
(1.24-1.60)
.42-.54
(1.07-1.37)
.38-.48
(.97-1.22)
.34-.43
(.86 -1.09)
.31-.39
(.79-.99)
.28-.35
(.71-.89)
1.00-1.24
(2. 54-3.15)
.75-.90
(1.90-2.29)
.63-.76
(1.60-1.93)
.54-.65
(1.37-1.65)
.48-.58
(1.22-1.47)
.43-.52
(1.09-1.32)
.39-.46
(.99-1.17)
.35-.42
(.89 -1.07)
1.25-1.49
(3.17-3.78)
.90-1.07
(2.29-2.72)
.76-.89
(1.93-2.26)
.65-.77
(1.65-1.96)
.58-.67
(1.47-1.70)
.52-.60
(1.32-1.52)
.46-.54
(1.17-1.37)
.42-.49
(1.07-1.24)
1.50-1.74
(3.81-4.42)
1.07-1.22
(2.72-3.10)
.89-1.02
(2.26-2.59)
.77-.88
(1.96-2.24)
.67-.77
(1.70-1.96)
.60-.69
(1.52-1.75)
.54-.62
(1.37-1.57)
.49-.56
(1.24-1.42)
1.75-1.99
(4.44-5.05)
1.22-1.53
(3.10-3.89)
1.02-1.28
(2.59-3.25)
.8 8 -1.10
(2.24-2.79)
.77-.96
(1.96-2.44)
.69-.86
(1.75 -2.18)
.62-.77
(1.57-1.96)
.56-.71
(1.42-1.80)
2.00-2.49
(5.08-6.32)
1.53-1.83
(3.89-4.65)
1.28-1.53
(3.25-3.89)
1.10-1.32
(2.79-3.35)
. 96 -1.16
(2.44-2.95)
.86-1.03
(2.18-2.62)
.77-.93
(1.96-2.36)
.71-.85
(1.80-2.16)
2.50-2.99
(6.35-7.59)
1.83-2.14
(4.65-5.44)
1.53-1.79
(3.89-4.55)
1.32-1.54
(3.35-3.91)
1.16-1.35
(2.95-3.43)
1.03-1.20
(2.62-3.05)
.93-1.08
(2.36-2.74)
.85-.99
(2.16-2.51)
3.00-3.49
(7.62-8.86)
2.14-2.44
(5.44-6.20)
1.79-2.05
(4.55-5.21)
1.54-1.76
(3.91-4.47)
1.35-1.54
(3.43-3.91)
1.20-1.37
(3.05-3.48)
1.08-1.24
(2.74 -3.15)
. 99 -1.13
(2.51-2.87)
3.50-3.99
( 8. 8 9 -10.13)
2.44-2.75
(6.20-6.98)
2.05-2.30
(5.21-5.84)
1.76-1.98
(4.47-5.03)
1.54-1.74
(3.91-4.42)
1.37-1.55
(3.48-3.94)
1.24-1.39
(3.15-3.53)
1.13-1.27
(2.87-3.23)
4.00-4.49
(10.16 -11.4 0 )
2.75-3.06
( 6 . 9 8 -7. 77 )
2.30-2.56
(5.84-6.50)
1.98-2.20
(5.03-5.59)
1.74-1.93
(4.42-4.90)
1.55-1.72
(3.94-4.37)
1.39-1.55
(3.53-3.94)
1.27-1.41
(3.23-3.58)
4.50-4.99
(11.43-12.67)
Note: *This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section. It is always recommended that, when multiple
cables are installed in a pulling grip, the tail end be banded and tightly taped after installation on the cable bundle. See page V-15 for end bands.
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Pulling Grips*
CAUTION: When a grip is used on multiple cables, the tail end of the grip should be banded after positioning on the cables.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: Three cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range, for a Split Grip select
the 1.75"-1.99" (4.44cm-5.05cm) range.
Kellems® Wire Management Products
Technical Information
Pulling Grips
www.hubbell-wiring.comV-26 Wiring Device-Kellems
®
T.H.W.N., T.H.H.N. and X.H.H.W. Building Wire
Cable
Diameter
Range
In. (cm)
Approx.
Breaking
Strength
Lbs. (N)
Approximate Number Of Wires In One Grip
Model Catalog Number
#14
19 Strand
#12
19 Strand
#10
19 Strand
#8
19 Strand
#6
19 Strand
#4
19 Strand
#3
19 Strand
#2
19 Strand
#1
37 Strand
#1/0
37 Strand
.25-.36
(.63-.91)
450
(2,002)
4-8 3-6 2-3 2111———J 25 03305001
.37-.49
(.94-1.24)
900
(4,003)
9-16 6 -11 4-6 32——111J 37 03305002
.50-.61
(1.27-1.55)
1,300
(5,782)
16-25 11-17 7-10 4-5 3-4 2 2 — — — J 50 03305003
.62-.74
(1.57-1.88)
1,950
(8 ,674)
26-37 18-25 11-14 6-8 5-6 3 3 2 2 — J 62 03305004
.75-.99
(1.90-2.51)
2,800
(12,454)
37-6 6 26-47 15-27 9-16 6 -11 4-7 4-5 3-4 32-3 J 75 03305005
1.00-1.24
(2. 54-3.15)
3,900
( 17, 3 4 7 )
66 -104 47-74 28-43 16-24 11-17 8 -10 6-8 5-7 4-5 4J 100 03305006
R.H.H., R.H., R.W. and R.H.W. Building Wire
Cable
Diameter
Range
In. (cm)
Approx.
Breaking
Strength
Lbs. (N)
Approximate Number Of Wires In One Grip
Model Catalog Number
#14
7 Strand
#12
7 Strand
#10
7 Strand
#8
7 Strand
#6
7 Strand
#4
7 Strand
#2
7 Strand
#1
7 Strand
#1/0
19 Strand
.25-.36
(.63-.91)
450
(2,002)
2 2 1 1 — — — — — J 25 03305001
.37-.49
(.94-1.24)
900
(4,003)
32-3 2—111—— J 37 03305002
.50-.61
(1.27-1.55)
1,300
(5,782)
4-5 4-5 3-4 2 — — — 1 — J 50 03305003
.62-.74
(1.57-1.88)
1,950
(8 ,674)
6-8 6-7 4-5 3 2 2 — — 1 J 62 03305004
.75-.99
(1.90-2.51)
2,800
(12,454)
9-16 8-14 6-10 4-6 3-4 3-4 2-3 2 — J 75 03305005
1.00-1.24
(2. 54-3.15)
3,900
( 17, 3 4 7 )
16-24 15-22 11-16 7-10 5-7 4-6 432-3 J 100 03305006
T.H.W. Building Wire
Cable
Diameter
Range
In. (cm)
Approx.
Breaking
Strength
Lbs. (N)
Approximate Number Of Wires In One Grip
Model Catalog Number
#14
7 Strand
#12
7 Strand
#10
7 Strand
#8
7 Strand
#6
7 Strand
#4
7 Strand
#2
7 Strand
#1
7 Strand
#1/0
19 Strand
.25-.36
(.63-.91)
450
(2,002)
2-4 2-3 2111——— J 25 03305001
.37-.49
(.94-1.24)
900
(4,003)
5-7 4-5 3-4 2 — — 1 — — J 37 03305002
.50-.61
(1.27-1.55)
1,300
(5,782)
8-11 6-8 5-7 3-4 2 2 — 1 1 J 50 03305003
.62-.74
(1.57-1.88)
1,950
(8 ,674)
12-16 9-12 8-10 5-6 3-4 3 2 — — J 62 03305004
.75-.99
(1.90-2.51)
2,800
(12,454)
17-30 13-24 11-19 7-10 5-7 4-5 3-4 2 2 J 75 03305005
1.00-1.24
(2. 54-3.15)
3,900
( 17, 3 4 7 )
31-48 25-37 20-30 11-17 8 -11 6-8 5-6 3-4 3J 100 03305006
Kellems® Wire Management Products
Technical Information
Junior Pulling Grips
Junior Pulling Grip Selection Chart
These charts are a general guide to assist in the selection of the correct Junior Pulling Grip for pulling various groupings of
building wire. It is not intended to be restrictive inasmuch as the use of “dummy" wires (short pieces of wire used to fill out
the Grip) or the tight taping of the wires into a compact bundle may increase or decrease the number of wires per Grip.
V-27www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Support Grips - Heavy Duty, Standard Duty, Light Duty
Tin-Coated Bronze/Stainless Steel
Solid eye assemblies provide eye reinforcement at support hardware
Four eye styles available: single (shown), double, universal, and offset
Identification tag shows: catalog number, diameter range,
agency approval, and bar code
The strand equalizer positions wires for equal loading throughout the
entire grip length
The positive action mesh grip is designed for light duty up to heavy duty.
Closed grips fit over the cable end, split grips wrap around the cable mid-span.
The standard material is nonmagnetic, tin-coated bronze. Selected items are
available in stainless steel. For exceptional immunity to rust and corrosion with
superior strength and flexibility for heavy duty support application in harsh
environments; contact the factory
The endless weave provides easy installation onto cable and can be
easily repositioned
www.hubbell-wiring.comV-28 Wiring Device-Kellems
®
Single Eye, Closed Mesh
For permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) 1,370 (6,094) 7 " (17.78 ) 10" (25.40) 02201013 02401013
.63"-.74" (1.60-1.88) 790 (3,514) 2,060 (9,163) 8" (20.32) 10" (25.40) 02201014 02401014
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,060 (9,163) 8" (20.32) 13" (33.02) 02201015 02401015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,678 (11, 912) 9" (22.86) 14" (35.56) 02201017 02401017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,490 (19,972) 10" (25.40) 15" (38.10 ) 02201018 02401018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,492 (19,981) 12" (30.48) 17" (43.18) 02201019 02401019
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 5,000 (22,241) 14" (35.56) 19" (48.26) 02201020 02401020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,940 (39,767) 16" (40.64) 21" (53.34) 02201021 02401021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 8,947 (39,798) 18" (45.72) 23" (58.42) 02201022 02401022
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 13,420 (59,695) 21" (53.34) 25" (63.50) 02201023 02401023
3.50"-3.99" (8.89-10.13) 4,900 (21,795) —24" (60.96) 27" (68.58) 02201024 —
Single Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) 1,370 (6,094) 7 " (17.78 ) 10" (25.40) 02202013 02402013
.63"-.74" (1.60-1.88) 790 (3,514) 2,0 6 6 ( 9,190) 8" (20.32) 10" (25.40) 02202014 02402014
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,060 (9,163) 8" (20.32) 13" (33.02) 02202015 02402015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,670 (11,876) 9" (22.86) 14" (35.56) 02202017 02402017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,490 (19,972) 10" (25.40) 15" (38.10 ) 02202018 02402018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,490 (19,972) 12" (30.48) 17" (43.18) 02202019 02402019
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 4,375 (19,461) 14" (35.56) 19" (48.26) 02202020 02402020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,947 (39,798) 16" (40.64) 21" (53.34) 02202021 02402021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 8,940 (39,767) 18" (45.72) 23" (58.42) 02202022 02402022
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 13,420 (59,695) 21" (53.34) 25" (63.50) 02202023 02402023
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 13,420 (59,695) 24" (60.96) 27" (68.58) 02202024 02402024
Single Eye, Split Mesh, Rod Closing
For support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 790 (3,514) 1,050 (4,670) 7 " (17.78 ) 8.5" (21.59) 02203013 02403013
.63"-.74" (1.60-1.88) 790 (3,514) 2,0 50 (9,119) 8" (20.32) 8.5" (21.59) 02203014 02403014
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,050 (9,119) 8" (20.32) 10.5" (26.67) 02203015 02403015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,650 (11,78 8) 9" (22.86) 12.5" (31.75) 02203017 02403017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,500 (20,017) 10" (25.40) 14.5" (36.83) 02203018 02403018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,500 (20,017) 12" (30.48) 15.5" (39.37) 02203019 02403019
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 6,000 (26,689) 14" (35.56) 16.5" (41.91) 02203020 02403020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,950 (39,812) 16" (40.64) 19.5" (49.53) 02203021 02403021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 7,75 0 (3 4, 474) 18" (45.72) 21.5" (54.61) 02203022 02403022
3.00"-3.49" (7.62-8.86) 5,750 (25,576) 8 , 50 0 (37, 810) 21" (53.34) 23.5" (59.69) 02203023 02403023
3.50"-3.99" (8.89-10.13) 5,750 (25,576) —24" (60.96) 25.5" (64.77) 02203024 —
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Standard Duty Support Grips
Single Eye, Single Weave, Tin-Coated Bronze and Stainless Steel
E
M
E
M
E
M
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-29www.hubbell-wiring.com Wiring Device-Kellems
®
Double Eye, Closed Mesh
For permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) 1,370 (6,094) 4" (10.16) 10" (25.40) 02201001 02401001
.63"-.74" (1.60-1.88) 790 (3,514) 2,060 (9,163) 4" (10.16) 10" (25.40) 02201002 02401002
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,060 (9,163) 4" (10.16) 13" (33.02) 02201003 02401003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,670 (11,877) 5" (12.70) 14" (35.56) 02201005 02401005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,490 (19,972) 5" (12.70) 15" (38.10) 02201006 02401006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,490 (19,972) 5" (12.70) 17" (43.18) 02201007 02401007
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 5,000 (22,241) 6" (15.24) 19" (48.26) 02201008 02401008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,940 (39,767) 6" (15.24) 21" (53.34) 02201009 02401009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 8,940 (39,767) 6" (15.24) 23" (58.42) 02201010 02401010
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 12,000 (53,379) 8" (20.32) 25" (63.50) 02201011 02401011
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 12,000 (53,379) 8" (20.32) 27" (68.58) 02201012 02401012
Double Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) —4" (10.16) 10" (25.40) 02202001 —
.63"-.74" (1.60-1.88) 790 (3,514) 2,0 6 6 ( 9,190) 4" (10.16) 10" (25.40) 02202002 02402002
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,060 (9,163) 4" (10.16) 13" (33.02) 02202003 02402003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,678 (11, 912) 5" (12.70) 14" (35.56) 02202005 02402005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,490 (19,972) 5" (12.70) 15" (38.10) 02202006 02402006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 3,750 (16,681) 5" (12.70) 17" (43.18) 02202007 02402007
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 5,000 (22,241) 6" (15.24) 19" (48.26) 02202008 02402008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,940 (39,767) 6" (15.24) 21" (53.34) 02202009 02402009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) — 6" (15.24) 23" (58.42) 02202010 —
3.00"-3.49" (7.62-8.86) 4,900 (21,795) —8" (20.32) 25" (63.50) 02202011 —
3.50"-3.99" (8.89-10.13) 4,900 (21,795) —8" (20.32) 27" (68.58) 02202012 —
Double Eye, Split Mesh, Rod Closing
For support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 790 (3,514) — 4" (10.16) 6.5" 02203001 —
.63"-.74" (1.60-1.88) 790 (3,514) 2,0 50 (9,119) 4" (10.16) 8.5" (21.59) 02203002 02403002
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,050 (9,119) 4" (10.16) 10.5" (26.67) 02203003 02403003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,650 (11,78 8) 5" (12.70) 12.5" (31.75) 02203005 02403005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 3,750 (16,681) 5" (12.70) 14.5" (36.83) 02203006 02403006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 3,750 (16,681) 5" (12.70) 15.5" (39.37) 02203007 02403007
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) 5,000 (22,241) 6" (15.24) 16.5" (41.91) 02203008 02403008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 8,950 (39,812) 6" (15.24) 19.5" (49.53) 02203009 02403009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 8,950 (39,812) 6" (15.24) 21.5" (54.61) 02203010 02403010
3.00"-3.49" (7.62-8.86) 5,750 (25,576) 11,150 (49,598) 8" (20.32) 23.5" (59.69) 02203011 02403011
3.50"-3.99" (8.89-10.13) 5,750 (25,576) —8" (20.32) 25.5" (64.77) 02203012 —
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Standard Duty Support Grips
Double Eye, Single Weave, Tin-Coated Bronze and Stainless Steel
E
M
E
M
E
M
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
www.hubbell-wiring.comV-30 Wiring Device-Kellems
®
Offset Eye, Closed Mesh
For permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) 1,370 (6,094) 4" (10.16) 10" (25.40) 02201037 02401037
.63"-.74" (1.60-1.88) 750 (3,336) 1,95 0 ( 8,674) 4" (10.16) 10" (25.40) 02201038 02401038
.75"-.99" (1.90-2.51) 950 (4,226) 2,060 (9,163) 4" (10.16) 13" (33.02) 02201039 02401039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 2,678 (11,912) 5" (12.70) 14" (35.56) 02201041 02401041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 4,490 (19,972) 5" (12.70) 15" ( 38.10) 02201042 02401042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 3,700 (16,458) 5" (12.70) 17" (43.18) 02201043 02401043
1.75"-1.99" (4.44-5.05) 2,000 (8,896) 4,375 (19,461) 6" (15.24) 19" (48.26) 02201044 02401044
2.00"-2.49" (5.08-6.32) 3,100 (13,789) 5,500 (24,465) 9" (22.86) 21" (53.34) 02201045 02401045
2.50"-2.99" (6.35-7.59) 3,100 (13,789) — 9" (22.86) 23" (58.42) 02201046 —
3.00"-3.49" (7.62-8.86) 3,800 (16,902) — 11" (27. 94) 25" (63.50) 02201047 —
3.50"-3.99" (8.89-10.13) 3,250 (14,480) — 11" (27.9 4 ) 27" (68.58) 02201048 —
Offset Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 500 (2,224) 1,370 (6,094) 4" (10.16) 10" (25.40) 02202037 02402037
.63"-.74" (1.60-1.88) 750 (3,336) 1,952 (8,683) 4" (10.16) 10" (25.40) 02202038 02402038
.75"-.99" (1.90-2.51) 950 (4,226) 2,060 (9,163) 4" (10.16) 13" (33.02) 02202039 02402039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 2,670 (11,877) 5" (12.70) 14" (35.56) 02202041 02402041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 4,490 (19,972) 5" (12.70) 15" ( 38.10) 02202042 02402042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 4,490 (19,972) 5" (12.70) 17" (43.18) 02202043 02402043
1.75"-1.99" (4.44-5.05) 1,800 (8,006) 4,375 (19,461) 6" (15.24) 19" (48.26) 02202044 02402044
2.00"-2.49" (5.08-6.32) 2,150 (9,5 63) 5,500 (24,465) 9" (22.86) 21" (53.34) 02202045 02402045
2.50"-2.99" (6.35-7.59) 2,150 (9,5 63) 5,500 (24,465) 9" (22.86) 23" (58.42) 02202046 02402046
3.00"-3.49" (7.62-8.86) 3,250 (14,480) 10,190 (4 5,327 ) 11" ( 27. 9 4) 25" (63.50) 02202047 02402047
3.50"-3.99" (8.89-10.13) 3,250 (14,480) — 11" (27.9 4 ) 27" (68.58) 02202048 —
Offset Eye, Split Mesh, Rod Closing
For support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 500 (2,224) 1,000 (4,448) 4" (10.16 ) 7 " (17.78 ) 02203037 02403037
.63"-.74" (1.60-1.88) 750 (3,336) 1,95 0 ( 8,674) 4" (10.16) 9" (22.86) 02203038 02403038
.75"-.99" (1.90-2.51) 950 (4,226) 1, 95 0 ( 8,674) 4" (10.16) 10" (25.40) 02203039 02403039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 2,50 0 (11,121) 5" (12.70) 12" (30.48) 02203041 02403041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 4,200 (18,683) 5" (12.70) 14" (35.56) 02203042 02403042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 4,500 (20,017) 5" (12.70) 15" ( 38.10) 02203043 02403043
1.75"-1.99" (4.44-5.05) 2,000 (8,896) 4,375 (19,461) 6" (15.24) 16" (40.64) 02203044 02403044
2.00"-2.49" (5.08-6.32) 3,100 (13,789) 8 ,350 (3 7,14 3 ) 9" (22.86) 19" (48.26) 02203045 02403045
2.50"-2.99" (6.35-7.59) 3,100 (13,789) — 9" (22.86) 20" (50.80) 02203046 —
3.00"-3.49" (7.62-8.86) 4,300 (19,126) 8,4 0 0 (37, 3 6 5 ) 11" ( 27. 9 4) 21" (53.34) 02203047 02403047
3.50"-3.99" (8.89-10.13) 4,900 (21,795) —11" ( 27. 9 4) 21" (53.34) 02203048 —
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Standard Duty Support Grips
Offset Eye, Single Weave, Tin-Coated Bronze and Stainless Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-31www.hubbell-wiring.com Wiring Device-Kellems
®
Universal Eye, Closed Mesh
For permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) 1,370 (6,094) 18" (45.72 10" (25.40) 02201051 02401051
.63"-.74" (1.60-1.88) 790 (3,514) 2,060 (9,163) 18" (45.72) 10" (25.40) 02201052 02401052
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,0 6 6 ( 9,190) 18" (45.72) 13" (33.02) 02201053 02401053
1.00"-1.24" (2.54-3.15) 1,610 (7,161) —18" (45.72) 14" (35.56) 02201050 —
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,490 (19,972) 18" (45.72) 15" (38.10) 02201054 02401054
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,490 (19,972) 18" (45.72) 17" (43.18) 02201055 02401055
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) —18" (45.72) 19" (48.26) 02201056 02401056
2.00"-2.49" (5.08-6.32) 3,260 (14,500) — 18" (45.72) 21" (53.34) 02201057 02401057
2.50"-2.99" (6.35-7.59) 3,260 (14,500) — 18" (45.72) 23" (58.42) 02201058 02401058
Universal Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 530 (2,357) —18" (45.72 10" (25.40) 02202050 —
.63"-.74" (1.60-1.88) 790 (3,514) 2,060 (9,163) 18" (45.72) 10" (25.40) 02202051 02402051
.75"-.99" (1.90-2.51) 1,020 (4,537) —18" (45.72) 13" (33.02) 02202052 —
1.00"-1.24" (2.54-3.15) 1,610 (7,161) —18" (45.72) 14" (35.56) 02202054 —
1.25"-1.49" (3.17-3.78) 1,610 (7,161) —18" (45.72) 15" (38 .10) 02202055 —
1.50"-1.74" (3.81-4.42) 1,610 (7,161) —18" (45.72) 17" (43.18) 02202056 —
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) —18" (45.72) 19" (48.26) 02202057 —
2.00"-2.49" (5.08-6.32) 3,260 (14,500) — 18" (45.72) 21" (53.34) 02202058 —
2.50"-2.99" (6.35-7.59) 3,260 (14,500) — 18" (45.72) 23" (58.42) 02202059 —
3.50"-3.99" (8.89-10.13) 4,900 (21,795) —18" (45.72) 27" (68.58) 02202061 —
Universal Eye, Split Mesh, Rod Closing
For support when cable end is not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.50"-.62" (1.27-1.57) 790 (3,514) — 18" (45.72 8.5" (21.59) 02203064 —
.63"-.74" (1.60-1.88) 790 (3,514) 2,0 50 (9,119) 18" (45.72) 8.5" (21.59) 02203065 02403065
.75"-.99" (1.90-2.51) 1,020 (4,537) 2,0 50 (9,119) 18" (45.72) 10.5" (26.67) 02203066 02403066
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 2,6 5 0 (11,788) 18" (45.72) 12.5" (31.75) 02203068 02403068
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 4,500 (20,017) 18" (45.72) 14.5" (36.83) 02203069 02403069
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 4,500 (20,017) 18" (45.72) 15.5" (39.37) 02203070 02403070
1.75"-1.99" (4.44-5.05) 2,150 (9, 56 3) —18" (45.72) 16.5" (41.91) 02203071 —
2.00"-2.49" (5.08-6.32) 3,260 (14,500) — 18" (45.72) 19.5" (49.53) 02203072 —
2.50"-2.99" (6.35-7.59) 3,260 (14,500) — 18" (45.72) 21.5" (54.61) 02203073 —
3.00"-3.49" (7.62-8.86) 5,750 (25,576) —18" (45.72) 23.5" (59.69) 02203074 —
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Standard Duty Support Grips
Universal Eye, Single Weave, Tin-Coated Bronze and Stainless Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
www.hubbell-wiring.comV-32 Wiring Device-Kellems
®
Heavy Duty, Single Eye, Closed Mesh
For heavy duty permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.75"-.99"
(1.90-2.51)
2,820 (12,543) 4,200 (18,683) 10" (25.40) 25" (63.50) 02206010 02406010
1.00"-1.24"
(2. 54-3.15)
4,280 (19,037) 7, 3 0 0 (32 ,472) 12" (30.48) 28 " ( 71.12) 02206011 02406 011
1.25"-1.49"
(3.17-3.78)
4,280 (19,037) 7, 3 0 0 (32 ,472) 12" (30.48) 30" (76.20) 02206012 02406012
1.50"-1.99"
(3.81-5.05)
4,280 (19,037) 11,150 (49,598) 12" (30.48) 34" (86.36) 02206013 02406013
Single Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.75"-.99"
(1.90-2.51)
2,820 (12,543) 4,200 (18,683) 10" (25.40) 25" (63.50) 02207010 02407010
1.00"-1.24"
(2. 54-3.15)
4,280 (19,037) 7, 3 0 0 (32 ,472) 12" (30.48) 28 " ( 71.12) 02207011 02407011
1.25"-1.49"
(3.17-3.78)
4,280 (19,037) 7, 3 0 0 (32 ,472) 12" (30.48) 30" (76.20) 02207012 02407012
1.50"-1.99"
(3.81-5.05)
4,280 (19,037) 11,150 (49,598) 12" (30.48) 34" (86.36) 02207013 02407013
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Heavy Duty Support Grips
Single Eye, Double Weave, Tin-Coated Bronze and Stainless Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-33www.hubbell-wiring.com Wiring Device-Kellems
®
Double Eye, Closed Mesh
For permanent support when cable end is available to be installed through grip.
Cable Diameter
Range Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.75"-.99"
(1.90-2.51)
2,820 (12,543) 4,250 (18,905) 10" (25.40) 25" (63.50) 02206001 02406001
1.00"-1.24"
(2. 54-3.15)
4,280 (19,037) 7, 3 0 0 ( 32,472 ) 10" (25.40) 28" ( 71.12) 02206002 02406002
1.25"-1.49"
(3.17-3.78)
4,280 (19,037) 7, 3 0 0 ( 32,472 ) 10" (25.40) 30" (76.20) 02206003 02406003
1.50"-1.99"
(3.81-5.05)
4,280 (19,037) 11,100 (49,375) 10" (25.40) 34" (86.36) 02206004 02406004
2.00"-2.49"
(5.08-6.32)
8,050 (35,806) 2 0,100 (89,40 9 ) 12" (30.48) 36" (91.44) 02206005 02406005
2.50"-2.99"
(6.35-7.59)
8,050 (35,806) 2 0,100 (89,40 9 ) 12" (30.48) 38" (96.52) 02206006 02406006
3.00"-3.49"
(7.62-8.86)
10,060 (44,747) 25, 20 0 (112,095 ) 12" (30.48) 40" (101.60) 02206007 02406007
3.50"-3.99"
( 8. 8 9 -10.13)
12,070 (53,687) —12" (30.48) 44" (111.76) 02206008 —
4.00"-4.49"
(10.16 -11.4 0 )
12,070 (53,687) —12" (30.48) 46" (116.84) 02206009 —
4.50"-4.99"
(11.43-12.67)
12,070 (53,687) —12" (30.48) 68" (172.72) 02208009 —
Double Eye, Split Mesh, Lace Closing
For support when cable end is not available.
Cable Diameter
Range Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.75"-.99"
(1.90-2.51)
2,820 (12,543) 4,250 (18,905) 10" (25.40) 25" (63.50) 02207001 02407001
1.00"-1.24"
(2. 54-3.15)
4,280 (19,037) 7, 3 0 0 ( 32,472 ) 10" (25.40) 28" ( 71.12) 02207002 02407002
1.25"-1.49"
(3.17-3.78)
4,280 (19,037) 7, 3 0 0 ( 32,472 ) 10" (25.40) 30" (76.20) 02207003 02407003
1.50"-1.99"
(3.81-5.05)
4,280 (19,037) 11,150 (49,598) 10" (25.40) 34" (86.36) 02207004 02407004
2.00"-2.49"
(5.08-6.32)
8,050 (35,806) 20,150 (89,632) 12" (30.48) 36" (91.44) 02207005 02407005
2.50"-2.99"
(6.35-7.59)
8,050 (35,806) 20,150 (89,632) 12" (30.48) 38" (96.52) 02207006 02407006
3.00"-3.49"
(7.62-8.86)
10,060 (44,747) 25, 20 0 (112,095 ) 12" (30.48) 40" (101.60) 02207007 02407007
3.50"-3.99"
( 8. 8 9 -10.13)
12,070 (53,687) 30,200 (134,336) 12" (30.48) 44" (111.76) 02207008 02407008
4.00"-4.49"
(10.16 -11.4 0 )
12,070 (53,687) 30,200 (134,336) 12" (30.48) 46" (116.84) 02207009 02407009
4.50"-4.99"
(11.43-12.67)
12,070 (53,687) —12" (30.48) 68" (172.72) 02209009 —
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Heavy Duty Support Grips
Double Eye, Double Weave, Tin-Coated Bronze and Stainless Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
www.hubbell-wiring.comV-34 Wiring Device-Kellems
®
.31''
(.79) Dia.
.29''
(.74)
4.86''
(12.42)
2.00''
(5.08)
Screw Hook
Catalog Number
20303001
Yield Strength 900 lbs (4003 N)
Light Duty, Single Eye, Closed Mesh, Single Weave
For permanent support when cable end is available to be installed.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.23"-.31" (.58-.79) 290 (1,290) 700 (3,114) 3 " ( 7.62 ) 3.75" (9.52) 02216001 02416001
.29"-.37" (.74-.94) 290 (1,290) 700 (3,114) 5" (12.70) 4.25" (10.79) 02216002 02416002
.35"-.44" (.89-1.12) 500 (2,224) 850 (3,781) 5.5" (13.97) 4.75" (12.06) 02216003 02416003
.41"-.50" (1.04-1.27) 500 (2,224) 850 (3,781) 5.5" (13.97) 5" (12.70) 02216004 02416004
.46"-.56" (1.17-1.42) 660 (2,936) 850 (3,781) 6" (15.24) 5.25" (13.33) 02216005 02416005
.52"-.62" (1.32-1.57) 790 (3,514) 1,050 (4,670) 7 " (17.78 ) 6.25" (15.87) 02216006 02416006
.58"-.68" (1.47-1.73) 790 (3,514) 1,050 (4,670) 7" (17.78) 6¹⁄⁄" (16.51) 02216007 02416007
.64"-.75" (1.63-1.90) 790 (3,514) 1,050 (4,670) 7 " (17.78 ) 6.75" (17.14) 02216008 02416008
.70"-.81" (1.78-2.06) 790 (3,514) 2,0 50 (9,119) 7 " (17.78 ) 7.25" (18.41) 02216009 02416009
.75"-.87" (1.90-2.21) 1,020 (4,537) 2,050 (9,119) 8" (20.32) 8" (20.32) 02216010 02416010
.81"-.94" (2.06-2.39) 1,020 (4,537) 2,0 50 (9,119) 8" (20.32) 8.25" (20.95) 02216011 02416 011
.87"-1.00" (2.21-2.54) 1,020 (4,537) —8" (20.32) 8.75" (22.22) 02216012 —
.94"-1.06" (2.39-2.69) 1,020 (4,537) 2,0 50 (9,119) 9" (22.86) 9" (22.86) 02216013 02416013
1.00"-1.18" (2.54-3.00) 1,020 (4,537) 2,05 0 ( 9,119) 9" (22.86) 9.5" (24.13) 02216014 02416014
1.06"-1.25" (2.69-3.17) 1,020 (4,537) 2,05 0 (9,119) 9" (22.86) 9.5" (24.13 ) 02216015 02416015
Heavy Duty, Single Eye, Closed Mesh, Multi-Weave
For permanent support when cable end is available to be installed.
Cable Diameter Range
Inches (cm)
Approx. Breaking Strength Lbs. (N) E
Inches (cm)
M
Inches (cm)
Tin-Coated
Bronze Stainless SteelTin-Coated Bronze Stainless Steel
.23"-.31" (.58-.79) 500 (2,224) 1,400 (6,228) 5" (12.70) 4.5" (11.43) 02217001 02417001
.29"-.37" (.74-.94) 500 (2,224) 1,15 0 (5,115) 5" (12.70) 5.5" (13.97) 02217002 02417002
.35"-.44" (.89-1.12) 870 (3,870) 1,70 0 ( 7, 562) 6" (15.24) 6.5" (16.51) 02217003 02417003
.41"-.50" (1.04-1.27) 870 (3,870) 1,70 0 ( 7, 5 6 2) 6" (15.24) 7.5" (19.05) 022170 04 02417004
.46"-.56" (1.17-1.42) 1,050 (4,670) 2,100 (9,341) 6" (15.24) 8" (20.32) 02217005 02417005
.52"-.62" (1.32-1.57) 1,050 (4,670) 2,100 (9,341) 7 " (17.78 ) 8.5" (21.59) 02217006 02417006
.58"-.68" (1.47-1.73) 1,050 (4,670) 2,100 (9,341) 7 " (17.78 ) 9.5" (24.13) 02217007 02417007
.64"-.75" (1.63-1.90) 1,390 (6,183) 4,161 (18 ,5 09) 7 " (17.78) 9.5" (24.13) 02217008 02417008
.70"-.81" (1.78-2.06) 1,390 (6,183) 4,100 (18,238) 8" (20.32) 10.5" (26.67) 02217009 02417009
.75"-.87" (1.90-2.21) 1,390 (6,183) — 8" (20.32) 10.5" (26.67) 02217010 —
.81"-.94" (2.06-2.39) 1,390 (6,183) — 8" (20.32) 10.5" (26.67) 02217011 —
.87"-1.00" (2.21-2.54) 1,79 0 ( 7, 9 6 2) 5,350 (23,798) 8" (20.32) 11.5" (29.21) 02217012 02417012
.94"-1.06" (2.39-2.69) 1,79 0 ( 7, 9 6 2) 5,300 (23,576) 9" (22.86) 12.5" (31.75) 02217013 02417013
1.00"-1.18" (2.54-3.00) 1,79 0 ( 7, 9 6 2 ) 5,300 (23,576) 9" (22.86) 13.5" (34.29) 02217014 02417014
1.06"-1.25" (2.69-3.17) 1,7 9 0 ( 7,9 6 2) 5,350 (23,798) 9" (22.86) 14.5" (36.83) 02217015 02417015
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Service Drop Grips
Single Eye, Tin-Coated Bronze and Stainless Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-35www.hubbell-wiring.com Wiring Device-Kellems
®
Light Duty, Universal Eye, Closed Mesh, Single Weave
For permanent support when cable end is available to be installed.
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
.23"-.31" (.58-.79) 290 (1,290) 9" (22.86) 3.75" (9.52) 02216016
.29"-.37" (.74-.94) 290 (1,290) 10" (25.40) 4.25" (10.79) 02216017
.35"-.44" (.89-1.12) 500 (2,224) 10" (25.40) 4.75" (12.06) 02216018
.41"-.50" (1.04-1.27) 500 (2,224) 11" ( 27. 9 4) 5" (12.70) 02216019
.46"-.56" (1.17-1.42) 660 (2,936) 12" (30.48) 5.25" (13.33) 02216020
.52"-.62" (1.32-1.57) 790 (3,514) 13" (33.02) 6.25" (15.87) 02216021
.58"-.68" (1.47-1.73) 790 (3,514) 13" (33.02) 6.5" (16.51) 02216022
.64"-.75" (1.63-1.90) 790 (3,514) 13" (33.02) 6.75" (17.14) 02216023
.70"-.81" (1.78-2.06) 790 (3,514) 13" (33.02) 7. 25" (18 .41) 02216024
.75"-.87" (1.90-2.21) 1,020 (4,537) 14" (35.56) 8" (20.32) 02216025
.81"-.94" (2.06-2.39) 1,020 (4,537) 14" (35.56) 8.25" (20.95) 02216026
.87"-1.00" (2.21-2.54) 1,020 (4,537) 14" (35.56) 8.75" (22.22) 02216027
.94"-1.06" (2.39-2.69) 1,020 (4,537) 15" (3 8.10 ) 9" (22.86) 02216028
1.00"-1.18" (2.54-3.00) 1,020 (4,537) 15" ( 38.10) 9.5" (24.13) 02216029
1.06"-1.25" (2.69-3.17) 1,020 (4,537) 15" (38.10 ) 9.5" (24.13) 02216030
Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave
For permanent support when cable end is available to be installed.
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
.23"-.31" (.58-.79) 500 (2,224) 11" (27.94) 4.5" (11.4 3) 02217016
.28"-.37" (.74-.94) 500 (2,224) 11" (27.9 4 ) 5.5" (13.97) 02217017
.35"-.44" (.89-1.12) 870 (3,870) 12" (30.48) 6.5" (16.51) 02217018
.41"-.50" (1.04-1.27) 870 (3,870) 12" (30.48) 7.5" (19.05) 02217019
.46"-.56" (1.17-1.42) 1,050 (4,670) 12" (30.48) 8" (20.32) 02217020
.52"-.62" (1.32-1.57) 1,050 (4,670) 13" (33.02) 8.5" (21.59) 02217021
.58"-.68" (1.47-1.73) 1,050 (4,670) 13" (33.02) 9.5" (24.13) 02217022
.64"-.75" (1.63-1.90) 1,390 (6,183) 13" (33.02) 9.5" (24.13) 02217023
.70"-.81" (1.78-2.06) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217024
.75"-.87" (1.90-2.21) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217025
.81"-.94" (2.06-2.39) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217026
.87"-1.00" (2.21-2.54) 1,7 9 0 ( 7, 9 6 2) 14" (35.56) 11.5" (29.21) 02217027
.94"-1.06" (2.39-2.69) 1,79 0 ( 7,9 62) 15" ( 38.10) 12.5" (31.75) 02217028
1.00"-1.18" (2.54-3.00) 1,790 (7,962) 15" (38 .10) 13.5" (34.29) 02217029
1.06"-1.25" (2.69-3.17) 1,79 0 ( 7,9 62) 15" ( 38.10) 14.5" (36.83) 02217030
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Service Drop Grips
Universal Eye, Tin-Coated Bronze
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
www.hubbell-wiring.comV-36 Wiring Device-Kellems
®
Safety Spring
Maximum Deflection
Inches/Lbs (cm/N)
Approx. Breaking
Strength Lbs. (N)
Length*
Inches (cm)
Diameter
Inches (cm)
Model
Lbs. (N) Catalog Number
2¾" at 40 lbs.
(6.98 at 178)
500 (2,224) 8.25" (20.95) .75" (1.90) 40 lb. spring
(178)
20302001
3¹⁄₈" at 80 lbs.
(7.94 at 356)
850 (3,781) 8.25" (20.95) 1" (2.54) 80 lb. spring
(356)
20302002
Note: Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar.
*No load.
Single Eye, Wide Range
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
.24"-.32" (.61-.81) 350 (1,557) 3" ( 7.62 ) 3.5" (8.89) 073041276**
.32"-.43" (.81-1.09) 450 (2,002) 4" (10.16 ) 4" (10.16) 073041277
.43"-.56" (1.09-1.42) 550 (2,446) 6" (15.24) 4.75" (12.06) 073041278
.56"-.73" (1.42-1.85) 1,000 (4,448) 7 " (17.78 ) 6" (15.24) 073041279
.73"-.85" (1.85-2.16) 1,400 (6,227) 7" (17.78 ) 6.75" (17.14) 073041280
.85"-1.00" (2.16-2.54) 1,400 (6,227) 8" (20.32) 8" (20.32) 073041281
1.00"-1.25" (2.54-3.17) 1,500 (6,672) 9" (22.86) 9.5" (24.13) 073041282
Universal Eye, Wide Range
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Inches (cm)
M
Inches (cm) Catalog Number
.32"-.43" (.81-1.09) 450 (2,002) 10" (25.40) 4" (10.16) 073041284
.43"-.56" (1.09-1.42) 550 (2,446) 12" (30.48) 4.75" (12.06) 073041285
.56"-.73" (1.42-1.85) 1,000 (4,448) 13" (33.02) 6" (15.24) 073041286
.73"-.85" (1.85-2.16) 1,400 (6,227) 13" (33.02) 6.75" (17.14) 073041287
.85"-1.00" (2.16-2.54) 1,400 (6,227) 14" (35.56) 8" (20.32) 073041288
1.00"-1.25" (2.54-3.17) 1,500 (6,672) 15" (38.10 ) 9.5" (24.13) 073041289
Note: E-Eye length. M-Mesh length at nominal diameter.
**Item indicated is not UL listed.
Kellems® Wire Management Products
Bus Drop Support Grips
Single Eye, Universal Eye, Galvanized Steel
Bus Drop Grips and Safety Springs
Kellems Bus Drop Grips are offered with either a single eye or universal bale attachment.
The mesh is single weave galvanized steel with the patented wide range construction.
They are suitable for indoor use only. Consult Technical Service for Stainless Steel Grips.
Application
Bus Drop Grips provide a safe, easy and economical method to support flexible cord or
bus drop cable at bus duct and other industrial areas.
Benefits
• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction.
Safety Spring
Springs can be used with single eye grips by disassembling drawbar from coil, placing
through eye and replacing drawbar.
Strain
Relief
Grip
Bus
Drop
Grips
Motor Box
Safety Spring
Strain
Relief
Grip
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-37www.hubbell-wiring.com Wiring Device-Kellems
®
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable
Sizes
In. (cm)
.50"- .62"
(1.27-1.57)
.6 3"-.74"
(1.60-1.88)
.75"- .99"
(1.90-2.51)
1.00"- 1.24"
(2. 54-3.15)
1.25"- 1.49"
(3.17-3.78)
1.50"-1.74"
(3.81-4.42)
1.75"-1.99"
(4.44-5.05)
2.00"- 2.49"
(5.08-6.32)
2.50" -2.99"
(6.35-7.59)
3.00"- 3.49"
(7.62-8.86)
3.50"- 3.99"
( 8. 8 9 -10.13)
Model R050 R062 R075 R100 R125 R150 R175 R200 R250 R300 R350
Length
In. (cm)
8" (20.32) 9" (22.86) 11" ( 27.9 4 ) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34)
Conduit
Sizes
Inches
Catalog Number
Approx. Breaking Strength Lbs. (N)
¾02 211106
530 (2,357)
——————————
102 211100
490 (2,179)
02 211101
790 (3,514)
—————————
1¼ 02211001
450 (2,002)
02211002
740 (3,292)
02211003
1,030 (4,581)
————————
1½
—
02 21100 6
690 (3,069)
02 211007
970 (4,315)
02 21100 9
1,610 (7,161)
———————
2
—
02 211107
640 (2,847)
02211010
920 (4,092)
02211012
1,520 (6,761)
02211013
1,610 (7,161)
——————
2½
————
02211017
1,510 (6,716)
02211018
1,610 (7,161)
02211019
2,150 (9,563)
————
3
———
02211022
1,340 (5,960)
02211023
1,400 (6,227)
02211024
1,490 (6,627)
02211025
1,990 (8,851)
02211026
3,260 (14,500)
———
3½
————— — —
02211033
2,970 (13,211)
02211034
3,260 (14,500)
— —
4
————— —
02211040
1,670 ( 7,24 8)
02 211041
2,680 (11,921)
02 211042
2,890 (12,855)
02 211043
4,080 (18,148)
—
5
— — — — — — — —
02 211061
2,150 (9,563)
02 211062
2,860 (12,721)
02211063
3,130 (13,922)
6
— — — — — — — — —
02 211072
2,245 (9,986)
02 211073
2,245 (9,986)
Note: See page V-45 for multiple cables in a single conduit riser grip.
Wire Management Products
Conduit Riser Grips
Ring Type, Single Weave, Tin-Coated Bronze
Single Weave, Closed Mesh
Kellems® Conduit Riser Support Grips are available in closed mesh and in split mesh
with lace or rod closures, to cover all applications including single cable or multiple wire
support. Refer to page V-45 for grip selection assistance for cable bundles. The standard
material is tin-coated bronze strand. The grip is permanently fastened to a support ring,
resulting in a one piece unit which will allow air ventilation within the conduit. The ring
will fit standard electrical rigid metal conduit and schedule 40 rigid PVC conduit only.
See page V-40 for ring dimensions. For permanent support when cable end is available
to be installed through the grip.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 and V-45.
www.hubbell-wiring.comV-38 Wiring Device-Kellems
®
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable
Sizes
In. (cm)
.75"- .99"
(1.90-2.51)
1.00"- 1.24"
(2. 54-3.15)
1.25"- 1.49"
(3.17-3.78)
1.50"-1.74"
(3.81-4.42)
1.75"- 1.99"
(4.44-5.05)
2.00"- 2.49"
(5.08-6.32)
2.50"- 2.99"
(6.35-7.59)
3.00"- 3.49"
(7.62-8.86)
3.50" -3.99"
( 8. 8 9 -10.13)
Model RS075 RS100 RS125 RS150 RS175 RS200 RS250 RS300 RS350
Length
In. (cm)
11" (27.94) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10 ) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34)
Conduit
Sizes
Inches
Catalog Number
Approx. Breaking Strength Lbs. (N)
1¼ 02212003
1,580 (7,0 2 8 )
————————
1½ 02212007
1,500 (6,672)
————————
202212010
1,430 (6,361)
02212012
1,930 (8,585)
02212013
2,040 (9,074)
——————
2½ — — 02212017
1,910 (8,496)
02212018
2,040 (9,074)
—————
3— — 02212023
1,780 ( 7,917 )
02212024
1,890 (8,407)
02212025
2,520 (11,209)
02212026
4,300 (19,126)
———
3½ —————02212033
3,910 (17,392)
02212034
4,300 (19,126)
— —
4————02212040
2,110 (9,385)
02212041
3,530 (15,701)
02212042
3,820 (16,991)
02212043
5,380 (23,930)
—
5——————02212061
2,860 (12,721)
— —
6————————02212073
2,955 (13,144)
Note: See page V-45 for multiple cables in a single conduit riser grip.
Kellems® Wire Management Products
Conduit Riser Grips
Ring Type, Double Weave, Tin-Coated Bronze
Double Weave, Split Mesh, Lace Closing
Kellems® Conduit Riser Support Grips will support cable runs in vertical or sloping
standard rigid conduit. The grip is fastened to a support ring which seats on the rim of
the conduit. The entire grip is supported by the conduit itself and no other hardware is
required. See page V-40 for ring dimensions. The rings will fit schedule 40 rigid PVC
conduit and standard electrical rigid metal conduit only. For permanent support when
cable end is not available.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 and V-45.
V-39www.hubbell-wiring.com Wiring Device-Kellems
®
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable
Sizes
In. (cm)
.75"- .99"
(1.90-2.51)
1.00"- 1.24"
(2. 54-3.15)
1.25"- 1.49"
(3.17-3.78)
1.50"-1.74"
(3.81-4.42)
1.75"- 1.99"
(4.44-5.05)
2.00"- 2.49"
(5.08-6.32)
2.50"- 2.99"
(6.35-7.59)
3.00"- 3.49"
(7.62-8.86)
3.50" -3.99"
( 8. 8 9 -10.13)
Model RR075 RR100 RR125 RR150 RR175 RR200 RR250 RR300 RR350
Length
In. (cm)
11" (27.94) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10 ) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34)
Conduit
Sizes
Inches
Catalog Number
Approx. Breaking Strength Lbs. (N)
1¼ 02213003
1,020 (4,537)
————————
1½ 02213007
970 (4,315)
02213009
1,610 (7,161)
———————
2—02213012
1,520 (6,761)
02213013
1,610 (7,161)
——————
2½ — — 02213017
1,510 (6,716)
02213018
1,610 (7,161)
—————
3— — 02213023
1,400 (6,227)
02213024
1,490 (6,627)
02213025
1,990 (8,851)
02213026
3,260 (14,500)
———
3½ —————02213033
2,970 (13,211)
———
4—————02213041
2,670 (11,876)
02213042
2,890 (12,855)
— —
Note: See page
V-45
for multiple cables in a single conduit riser grip.
Kellems® Wire Management Products
Conduit Riser Grips
Ring Type, Single Weave, Tin-Coated Bronze
Single Weave, Split Mesh, Rod Closing Benefits
• Easy and fast to install.
• Will not damage electrical cable.
• Allows cable to expand or contract.
• Ideal way to hold cable in vertical conduit.
• Prevents cable creep in conduit.
• Helps prevent cable pullouts.
• The rings will fit schedule 40 rigid PVC conduit and standard electrical
rigid metal conduit only.
• For support when cable end is not available.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 and V-45.
www.hubbell-wiring.comV-40 Wiring Device-Kellems
®
Kellems® Wire Management Products
Conduit Riser Grips
Conduit Riser Support Grip-Ring Dimensions
O.D.
I.D.
T
T
S
O.D.
I.D.
T
Conduit Size ¾" and 1"
Conduit Size 1¼" to 6"
Conduit Size
Inches
Ring
Number
O.D.
Inches (cm)
I.D.
Inches (cm)
S
Inches (cm)
T
Inches (cm)
¾
1
1¼
1½
2
2½
3
3½
4
4½
5
6
C-¾
C-1
C-1¼
C-1½
C-2
C-2½
C-3
C-3½
C-4
C-4½
C-5
C-6
.94" (2.39)
1.17" (2.97)
1.50" (3.81)
1.76" (4.47)
2.23" (5.66)
2.67" (6.78)
3.20" (8.13)
3.80" (9.65)
4.30" (10.92)
4.80" (12.19)
5.30" (13.46)
6.30" (16.00)
.62" (1.57)
.80" (2.03)
1.03" (2.62)
1.23" (3.12)
1.55" (3.94)
2.05" (5.21)
2.55" (6.48)
3.05" (7.75)
3.55" (9.02)
4.03" (10.24)
4.46" (11.3 3)
5.36" (13.61)
—
—
1.31" (3.33)
1.52" (3.86)
1.97" (5.00)
2.40" (6.10)
2.97" (7.54)
3.47" (8.81)
3.94" (10.01)
4.45" (11.30 )
4.96" (12.60)
5.96" (15.14)
.19" (.48)
.19" (.48)
.16" (.41)
.16" (.41)
.16" (.41)
.16" (.41)
.22" (.56)
.22" (.56)
.22" (.56)
.22" (.56)
.22" (.56)
.25" (.63)
Conduit Ring Dimensions
Ring dimensions are found in the chart below. The ring material is corrosion resistant.
These rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal
conduit only.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-45.
V-41www.hubbell-wiring.com Wiring Device-Kellems
®
Support Grip Selection Chart
Grip Styles Application Page
Closed mesh
Split lace closing
Split rod closing
Material*
Standard support grips
Heavy duty grips
Service drop
Bus drop
Conduit riser
Fiber optic cable support grips
Standard, permanent support, cable end available.
Standard, permanent support, cable end unavailable.
Standard, temporary support, cable end unavailable. Tape or band tail end of
wire mesh grip after positioning for permanent support.
Tin-coated bronze standard or stainless steel by special request.
Support vertical runs to 99 ft. loads to 600 lbs.
Support vertical runs over 100 ft. loads over 600 lbs.
Light duty to support service entrance cable.
Light duty support, indoors only, on Bus drop cable.
Support cable runs in rigid (Schedule 40) conduit.
Support fiber optic cable.
V-28 to V-36
V-28 to V-33
V-28 to V-31
V-28 to V-34
V-28 to V-31
V-32, V-33
V-34, V-35
V-36
V-37 to V-39
V-50
Note: *Most catalog listed support grips are made of tin-coated bronze strand. To order stainless steel support grips, change the first three catalog number digits from
022-0x-xxx to 024-0x-xxx. Consult Technical Service for details.
Eye Styles
Select the Correct Support Grip
Each Kellems grip is designed to work on a specific
range of cable diameters.
Step 1 Refer to the Kellems chart below to determine
the grip style best suited for your application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your
cable diameter.
Step 4 Whenever possible, use a closed mesh that
assembles over the cable end. If the cable end
is not available, use a split mesh.
Step 5 Where available, select an eye style that suits
your needs.
Step 6 Select the proper material—tinned bronze or
stainless steel*.
Step 7 Estimate the tension to be put on the grip,
establish the working load you require and
compare this to the listed approximate breaking
strength of the grip to insure that the grip will be
strong enough. Refer to page V-42 for safety
and working load considerations.
Kellems® Wire Management Products
Technical Information
Support Grips
Kellems® Support Grips
Kellems Support Grips are used to hold the weight of electrical cable as it hangs in a vertical, sloping or horizontal position.
Electrical cable must be supported, or its dead weight can cause excessive strain or pullout at the connections resulting in
power failure. Support grips also absorb additional strain from flexure, vibration, expansion and contraction. Kellems Support
Grips listed in this catalog are made of high grade, non-magnetic tin-coated bronze strand. Stainless steel grips, made of alloy
302–304 SST for severe service or unusual environmental conditions, are available on request.
Single Double Universal Offset
1. Support grips are to be installed by a qualified individual in
accordance with all applicable national and local safety, electrical
and rigging codes.
2. Ensure that the correct grip is selected for your specific needs.
3. Do not use a support grip for any application other than
supporting cable.
4. Thoroughly examine the grip for damage. Do not use a damaged grip.
5. Ensure that the recommended work load of the grip is suitable for
the application. Never use grips at their approximated rated breaking
strength. A safety factor of 10 is recommended for support grips.
6. Do not alter grips in any way. For example, do not flatten, straighten,
bend or otherwise modify eye tubes, hooks, and strand equalizers.
7. Do not attach any type of hook, clamp or other hardware directly to
the stranded bale of a “U” eye support grip. The formed eye tube is
the only acceptable means of attachment to external hardware.
8. Always apply 2 bands at 1" and 2" respectively, from the tail end of
the mesh to guard against accidental release of the grip. Accidental
release can occur if an object contracts and pushes against the tail
end of the mesh, thereby expanding and releasing it’s hold.
CAUTION: It is very important to comply with all of the
following precautions.
www.hubbell-wiring.comV-42 Wiring Device-Kellems
®
Examples
Approx. Breaking Safety Max. Recommended
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number
Pulling Grips 27,200 (120,986) 5 5,4 40 (24,197 ) 03301027
Support Grips 1,610 (7,161) 10 161 (716) 02202019
The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to
take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable for the application.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric unit
of weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Support Grip Materials
Material Features Grip Type
Tin-coated bronze wire • Corrosion resistant for normal outside areas • Support grips
• Non-magnetic • Service drop grips
• Moderate strength • Conduit riser grips
Stainless steel wire • High strength • Support grips
(302-304) • Corrosion resistant • Hose containment grips
Galvanized steel wire • Slightly magnetic • Bus drop grips
• Not subject to continuous
outside environment
Approvals
CSA Certifications are indicated on appropriate product catalog pages.
Note: It is always recommended that the tail end of the grip be banded after the installation on the cable to prevent accidental release of the mesh.
See page V-15 for end bands.
Kellems® Wire Management Products
Technical Information
Support Grips
The broad application of Kellems grips on a wide variety of
objects requires that adequate safety factors be used to
establish working loads. The approximate breaking strength
of a Kellems grip represents an average calculation based on
data established from actual direct tension testing done in
our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are never
the same. The tension, diameter, movement, number of
objects gripped, gripping surface, and the attachments used
are just some of the factors which vary with each application.
These factors, together with the effects of abrasion,
corrosion, prior use or abuse and any other variables of a
specific application, must be considered by the user and
the grip replaced as appropriate. Where the conditions of
the application are not well defined or known, or where risk
of injury to persons or property is involved, a greater safety
factor should be utilized.
Any warranty as to quality, performance or fitness for
use of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored, handled,
used, maintained, and inspected by the user at a frequency
appropriate for the use and condition of the grip.
Safety And Working Load Factors For Wire Mesh Grips
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling grips,
and ten for catalog listed support grips.
V-43www.hubbell-wiring.com Wiring Device-Kellems
®
Split Support Grip Lace Closing Instructions
Single Weave Grips should be laced with single strand lacing; double weave with double strand. Lacing strands should be
the same material as the grip. Kellems supplies the appropriate lacing with each grip.
1. Start the lacing at the lead or anchoring end of the grip. Thread the lacings through the first two loops of the split and
pull through until the lacings are centered at this point. Lace as you would your shoe, crossing the lacings before lacing
the next two loops.
2. Don’t pull lacing too tight. Leave a space between adjoining loops approximately equal to the width of one diamond of
the mesh.
3. Twist the lacing strands tightly together at the tail end of the grip.
4. Wrap the ends of the lacings once or twice tightly around the tail of the grip, twisting the ends together securely.
Excess lace can be cut off.
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the mesh pass
around the rod and match up with the strands from the opposite direction. The rod does not touch the cable at any point and
therefore cannot cut the cable. Rod Closing Grips are reusable. They may be removed and reused as many times as desired.
1. Fast to install
Wrap the grip around the cable and thread the rod through the pre-formed loops with a corkscrew motion, using the
curved end of the rod to engage the loops.
2. The action required is a steady push and twist simultaneously. The fingers of the left hand are used to bring the loops
together just ahead of the hook on the end of the rod.
3. To remove, simply pull the rod out.
Kellems® Wire Management Products
Technical Information
Support Grips
www.hubbell-wiring.comV-44 Wiring Device-Kellems
®
Number of Cables in One Grip
23456 and 7 8 9
Grip Dia. Range
Inches (cm)
.30-.38
(.76-.97)
.25-.31
(.63-.79)
.22-.27
(.56-.69)
.19 -.24
(.48-.61)
.17-.22
(.43-.56)
.15-.19
(.38-.48)
.14 -.18
(.36-.46)
.50-.61
(1.27-1.55)
.38-.44
(.97-1.12)
.31-.36
(.79-.91)
.27-.31
(.69-.79)
.24-.29
(.61-.74)
.22-.26
(.56-.66)
.19 -.2 3
(.48-.58)
.18-. 21
(.46-.53)
.62-.74
(1.57-1.88)
.44-.59
(1.12-1.50)
.36-.49
(.91-1.24)
.31-.42
(.79-1.07)
.29-.38
(.74-.97)
.26-.34
(.66-.86)
.23-.31
(.58-.79)
.21-.28
(.53-.71)
.75-.99
(1.90-2.51)
.59-.75
(1.50 -1.90)
.49-.63
(1.24-1.60)
.42-.54
(1.07-1.37)
.38-.48
(.97-1.22)
.34-.43
(.86 -1.09)
.31-.39
(.79-.99)
.28-.35
(.71-.89)
1.00-1.24
(2. 54-3.15)
.75-.90
(1.90-2.29)
.63-.76
(1.60-1.93)
.54-.65
(1.37-1.65)
.48-.58
(1.22-1.47)
.43-.52
(1.09-1.32)
.39-.46
(.99-1.17)
.35-.42
(.89 -1.07)
1.25-1.49
(3.17-3.78)
.90-1.07
(2.29-2.72)
.76-.89
(1.93-2.26)
.65-.77
(1.65-1.96)
.58-.67
(1.47-1.70)
.52-.60
(1.32-1.52)
.46-.54
(1.17-1.37)
.42-.49
(1.07-1.24)
1.50-1.74
(3.81-4.42)
1.07-1.22
(2.72-3.10)
.89-1.02
(2.26-2.59)
.77-.88
(1.96-2.24)
.67-.77
(1.70-1.96)
.60-.69
(1.52-1.75)
.54-.62
(1.37-1.57)
.49-.56
(1.24-1.42)
1.75-1.99
(4.44-5.05)
1.22-1.53
(3.10-3.89)
1.02-1.28
(2.59-3.25)
.8 8 -1.10
(2.24-2.79)
.77-.96
(1.96-2.44)
.69-.86
(1.75 -2.18)
.62-.77
(1.57-1.96)
.56-.71
(1.42-1.80)
2.00-2.49
(5.08-6.32)
1.53-1.83
(3.89-4.65)
1.28-1.53
(3.25-3.89)
1.10-1.32
(2.79-3.35)
. 96 -1.16
(2.44-2.95)
.86-1.03
(2.18-2.62)
.77-.93
(1.96-2.36)
.71-.85
(1.80-2.16)
2.50-2.99
(6.35-7.59)
1.83-2.14
(4.65-5.44)
1.53-1.79
(3.89-4.55)
1.32-1.54
(3.35-3.91)
1.16-1.35
(2.95-3.43)
1.03-1.20
(2.62-3.05)
.93-1.08
(2.36-2.74)
.85-.99
(2.16-2.51)
3.00-3.49
(7.62-8.86)
2.14-2.44
(5.44-6.20)
1.79-2.05
(4.55-5.21)
1.54-1.76
(3.91-4.47)
1.35-1.54
(3.43-3.91)
1.20-1.37
(3.05-3.48)
1.08-1.24
(2.74 -3.15)
. 99 -1.13
(2.51-2.87)
3.50-3.99
( 8. 8 9 -10.13)
2.44-2.75
(6.20-6.98)
2.05-2.30
(5.21-5.84)
1.76-1.98
(4.47-5.03)
1.54-1.74
(3.91-4.42)
1.37-1.55
(3.48-3.94)
1.24-1.39
(3.15-3.53)
1.13-1.27
(2.87-3.23)
4.00-4.49
(10.16 -11.4 0 )
2.75-3.06
( 6 . 9 8 -7. 77 )
2.30-2.56
(5.84-6.50)
1.98-2.20
(5.03-5.59)
1.74-1.93
(4.42-4.90)
1.55-1.72
(3.94-4.37)
1.39-1.55
(3.53-3.94)
1.27-1.41
(3.23-3.58)
4.50-4.99
(11.43-12.67)
Note: *This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Riser multiple cable selection, see page V-45.
It is always recommended that, when multiple cables are installed in a Support Grip, the tail end of the grip be banded after installation on the cable bundle.
See page Tech-23 for cable and wire charts.
For Support Grips Only*
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .89" (2.26) diameter, for a Closed Grip select the 1.50"-1.74" (3.81-4.42) range, for a Split Grip select the
1.75"-1.99" (4.44-5.05) range.
Kellems® Wire Management Products
Technical Information
Support Grips
V-45www.hubbell-wiring.com Wiring Device-Kellems
®
Number of Equal Diameter Cables in One Grip
23456 and 7 8 9
Grip Dia. Range
Inches (cm)
.29-.36
(.74-.91)
.24-.30
(.61-.76)
.21-.25
(.53-.63)
.18-. 22
(.46-.56)
.16 -. 20
(.41-.51)
.15-.18
(.38-.46)
.14 -.17
(.36-.43)
.50-.62
(1.27-1.57)
.37-.43
(.94-1.09)
.31-.36
(.79-.91)
.26-.30
(.66-.76)
.23-.27
(.58-.69)
.21-.24
(.53-.61)
.19 -.2 2
(.48-.56)
.18-. 20
(.46-.51)
.63-.74
(1.60-1.88)
.44-.58
(1.12-1.47)
.37-.48
(.94-1.22)
.31-.41
(.79-1.04)
.28-.36
(.71-.91)
.25-.32
(.63-.81)
.23-.29
(.5 8-.74)
.21-.27
(.53-.69)
.75-.99
(1.90-2.51)
.59-.72
(1.50 -1.83)
.49-.60
(1.24-1.52)
.42-.51
(1.07-1.30)
.37-.45
(.9 4-1.14)
.33-.40
(.84-1.02)
.30-.36
(.76-.91)
.28-.34
(.71-.86)
1.00-1.24
(2. 54-3.15)
.73-.87
(1.85-2.21)
.61-.72
(1.55-1.83)
.52-.61
(1.32-1.55)
.46-.54
(1.17-1.37)
.41-.48
(1.04-1.22)
.37-.43
(.94-1.09)
.35-.40
(.89 -1.02)
1.25-1.49
(3.17-3.78)
.88-1.01
(2.24-2.57)
.73-.85
(1.85-2.16)
.62-.71
(1.57-1.80)
.55-.63
(1.40-1.60)
.49-.56
(1.24-1.42)
.44-.51
(1.12-1.30)
.41-.47
(1.04-1.19)
1.50-1.74
(3.81-4.42)
1.02-1.16
(2.59-2.95)
.86-.96
(2.18-2.44)
.72-.81
(1.83-2.06)
.64-.72
(1.63-1.83)
.57-.64
(1.45-1.63)
.52-.58
(1.32-1.49)
.48-.54
(1.22-1.37)
1.75-1.99
(4.44-5.05)
1.17-1.44
(2.97-3.66)
.97-1.20
(2.46-3.05)
.82-1.02
(2.08-2.59)
.73-.90
(1.85-2.29)
.65-.80
(1.65-2.03)
.59-.72
(1.50 -1.83)
.55-.67
(1.40-1.70)
2.00-2.49
(5.08-6.32)
1.45-1.73
(3.68-4.39)
1.21-1.45
(3.07-3.68)
1.03-1.22
(2.62-3.10)
.91-1.08
(2.31-2.74)
.81-.96
(2.06-2.44)
.73-.87
(1.85-2.21)
.68-.81
(1.73-2.06)
2.50-2.99
(6.35-7.59)
1.74 -2.0 2
(4.42-5.13)
1.46-1.69
(3.71-4.29)
1.23-1.43
(3.12-3.63)
1.09-1.26
(2.77-3. 20)
.97-1.11
(2.46-2.82)
.83-1.01
(2.11-2.57)
.82-.94
(2.08-2.39)
3.00-3.49
(7.62-8.86)
2.03-2.31
(5.16-5.87)
1.70-1.93
(4.32-4.90)
1.44-1.63
( 3. 66 - 4.14)
1.27-1.44
(3.23-3.66)
1.12-1.27
(2.84-3.23)
1.02-1.15
(2.59-2.92)
.95 -1.08
(2.41-2.74)
3.50-3.99
( 8. 8 9 -10.13)
Note: *This chart is to be used for determining grip size when multiple cables are held in a single Conduit Riser Grip. For Support Grip multiple cable selection, see page V-44.
It is always recommended that, when multiple cables are installed in a Conduit Riser Grip, the tail end of the grip be banded after installation on the cable bundle.
See page Tech-23 for cable and wire charts.
Kellems® Wire Management Products
Technical Information
Conduit Riser Support Grips
For Conduit Riser Grips Only*
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .85" (2.16) diameter, for a Closed Grip select the 1.50"-1.74" (3.81-4.42) range, for a Split Grip select the
1.75"-1.99" (4.44-5.05) range.
www.hubbell-wiring.comV-46 Wiring Device-Kellems
®
OPTISOK® Grip is a revolutionary tool to pull
preterminated fiber optic cables. They will protect
the connectors and guide the bundle through the
pulling environment
Pulling Grips are used for outside plant cable.
They are easy to install and remove, reusable,
and have a slim profile for small build up
Grips for cable support are easy to install or position.
They come in a closed style when the cable end is
available, and a split rod style for mid-span installation.
Will support the cable’s weight as it hangs in vertical,
sloping or horizontal position
Kellems® Wire Management Products
Fiber Optic Cable Grips
Pulling and Support Grips
V-47www.hubbell-wiring.com Wiring Device-Kellems
®
OPTISOK® Non-Metallic Fiber Optic Pulling Tool
Bundle/Size Range
Inches (cm)
Approx. O/A Length
Inches (cm)
Ring O.D.
Inches (cm)
Ring Thickness
Inches (cm)
Maximum Work
Load Lbs. (N) Catalog Number
.125"-.562" (.318-1.427) 28 " ( 71.12) .71" (1.803) .10" (.254) 30 (133) CCPS1
.250"-.750" (.635-1.905) 31" ( 78.74) .71" (1.803) .10" (.254) 40 (178) CCPS2
.750"-1.750" (1.905-4.445) 33" (83.82) 1.57" (3.988) .16" (.4 0 6) 50 (222) CCPS3
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
Diameter Range
Inches (cm)
Mesh Length
Inches (cm)
Eye Length
Inches (cm)
Eye Diameter
Inches (cm)
Lug Diameter
Inches (cm)
Maximum Breaking
Strength Lbs. (N) Catalog Number
.312"-.625" (.79-1.59) 2 2. 5" ( 57.15 ) 6.3" (16.00) .20" (.51) .51" (1.30) 3,000 (13,344) PFOLT312
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Special Purpose
OPTISOK® Non-metallic Fiber Optic Pulling Tool For Preterminated,
Inside Plant Fiber Optic Cables and Bundles of Twisted Pair
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-51 to V-54.
www.hubbell-wiring.comV-48 Wiring Device-Kellems
®
Fiber Optic Pulling Grip, Flexible Eye
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm)
D
Approx.
Inches (cm) Catalog Number
.10"-.22" (.25-.56) 1,000 (4,448) 5.5" (14) 9" (23) 0.8" (2) 033291000
.21"-.35" (.53-.89) 1,500 (6,672) 5.5" (14) 14" (36) 0.8" (2) 033291001
.32"-.48" (.81-1.22) 2,200 (9,786) 6.0" (15) 18" (46) 0.9" (2.29) 033291002
.42"-.61" (1.07-1.55) 2,800 (12,454) 6.0" (15) 21" (53) 0.9" (2.29) 033291003
.53"-.74" (1.35-1.88) 3,300 (14,678) 6.5" (17) 24" (61) 1.3" (3.30) 033291004
.64"-.87" (1.63-2.21) 4,700 (20,906) 6.5" (17) 27" (69) 1.3" (3.30) 033291005
Fiber Optic Pulling Grip, Swivel Eye
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm)
D
Approx.
Inches (cm) Catalog Number
.21"-.35" (.53-.89) 1,500 (6,672) 4.0" (10.16) 14" (35.56) 0.9" (2.29) 033291008
.32"-.48" (.81-1.22) 2,200 (9,786) 4.0" (10.16) 18" (45.72) 0.9" (2.29) 033291009
.42"-.61" (1.07-1.55) 2,800 (12,454) 4.0" (10.16) 21" (53.34) 0.9" (2.29) 033291010
.53"-.74" (1.35-1.88) 3,250 (14,457) 4. 8" (12.19) 24" (60.96) 1.3" (3.30) 033291011
.64"-.87" (1.63-2.21) 4,700 (20,906) 4.8" (12.19) 27" (68.58) 1.3" (3.30) 033291012
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Double/Single Weave Mesh, Galvanized Steel, for Outside Plant Cable
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-51 to V-54.
EM
D
EM
D
V-49www.hubbell-wiring.com Wiring Device-Kellems
®
Fiber Optic Pulling Grip, Flexible Eye, Low Profile, Double/Single Weave Mesh
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm) Catalog Number
.10"-.22 (.25-.56) 900 (4,003) 7. 5" (19) 10" (25) 0 33291193
.21"-.35" (.53-.89) 1,400 (6,227) 7. 5" (19 ) 14" (36) 033291194
.32"-.48" (.81-1.22) 2,000 (8,896) 8.5" (22) 19" (48) 0332 91195
.42"-.61" (1.07-1.55) 2,500 (11,120) 8.5" (22) 21" (53) 033291196
.53"-.74" (1.35-1.88) 3,000 (13,344) 8.5" (22) 23" (58) 033291197
.64"-.87" (1.63-2.21) 4,200 (18,682) 8.5" (22) 25" (64) 033291198
.75"-1.0 0" (1.90-2.54) 4,200 (18,682) 8.5" (22) 28" (71) 0 33291199
Fiber Optic Slack Pulling Grip, Split Mesh Rod Closing, Single Weave
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm) Catalog Number
.25"-.37" (.63-.94) 300 (1,334) 3" ( 7.6 ) 4.7" (12) 033291015
.38"-.49" (.97-1.24) 800 (3,558) 3" ( 7.6) 5" (13) 033291016
.50"-.61" (1.27-1.55) 800 (3,558) 3" ( 7.6) 7. 5" (19 ) 033291017
.62"-.74" (1.57-1.88) 1,200 (5,338) 3 " ( 7.6 ) 8" (20) 033291018
Note: E-Eye length. M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Galvanized Steel for Outside Plant Cable
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-51 to V-54.
EM
EM
www.hubbell-wiring.comV-50 Wiring Device-Kellems
®
E
M
E
M
Kellems® Wire Management Products
Fiber Optic Cable Support Grips
Single Weave, Tin-Coated Bronze
Fiber Optic Single Eye Cable Support Grip, Closed Mesh, Single Weave
For permanent support when cable end is available to be installed through grip.
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm) Catalog Number
.18"-.25" (.46-.63) 300 (1,334) 3" ( 7.6) 1.7" (4.3) 022291000
.23"-.32" (.58-.81) 300 (1,334) 3" ( 7. 6 ) 2.5" (6.4) 022291001
.30"-.39" (.76-.99) 300 (1,334) 4" (10) 2.5" (6.4) 022291002
.37"-.48" (.94-1.22) 300 (1,334) 5" (13) 4" (10) 022291003
.46"-.58" (1.17-1.47) 400 (1,779) 6" (15) 4" (10) 022291004
.56"-.71" (1.42-1.80) 600 (2,669) 7" (18) 5.5" (14) 022291005
.69"-.88" (1.75-2.24) 800 (3,558) 8" (20) 6" (15) 022291006
Fiber Optic Single Eye Cable Support Grip, Split Mesh, Rod Closing, Single Weave
For support when cable end not available.
Cable Diameter Range
Inches (cm)
Approx. Breaking
Strength Lbs. (N)
E
Approx.
Inches (cm)
M
Approx.
Inches (cm) Catalog Number
.18"-.25" (.46-.63) 300 (1,334) 3" ( 7.6) 2.5" (6.4) 022291016
.23"-.32" (.58-.81) 300 (1,334) 3" ( 7. 6 ) 2.5" (6.4) 022291017
.30"-.39" (.76-.99) 300 (1,334) 4" (10) 2.5" (6.4) 022291018
.37"-.48" (.94-1.22) 300 (1,334) 5" (13) 4" (10) 022291019
.46"-.58" (1.17-1.47) 400 (1,779) 6" (15) 5" (13) 022291020
.56"-.71" (1.42-1.80) 600 (2,669) 7" (18) 5" (13) 022291021
.69"-.88" (1.75-2.24) 800 (3,558) 8" (20) 6" (15) 022291022
Note: E-Eye length. M-Mesh length at nominal diameter.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-51 to V-54.
V-51www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems has wide experience with grips for use with
fiber optic cable. As the industry leader in producing
wire mesh grips for the stringent requirements of
fiber optic applications, Kellems has developed
several series of grips for use with fiber optic
communications cable.
These grips include pulling grips with built in swivels,
grips with steel ends to protect fragile cable ends,
grips with low profiles to pull cables in tight places
and the OPTISOK® an effective tool to place
preterminated cables. Also available are grips to
support fiber optic cable.
Kellems® Wire Management Products
Technical Information
Fiber Optic Pulling and Support Grips
Examples
Approx. Breaking Safety Max. Recommended
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number
Pulling Grips 2,500 (11,120) 5 500 (2,224) 033291196
Support Grips 400 (1,779) 10 40 (178) 022291004
The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to
take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable to for the application.
Fiber Optic Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Pulling grips
• Not subject to continuous outside environment
Tin-coated bronze wire • Corrosion resistant for normal outside areas • Support grips
• Non-magnetic
• Moderate strength
Non-metallic braid • Superior flex life • OPTISOK®
• Non-conductive
• Corrosion resistant
• Moderate strength
Approvals
CSA Certification is indicated on appropriate product catalog pages.
The broad application of Kellems grips on a wide variety of
objects requires that adequate safety factors be used to
establish working loads. The approximate breaking strength
of a Kellems grip represents an average calculation based
on data established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are never
the same. The tension, diameter, movement, number of
objects gripped, gripping surface, and the attachments used
are just some of the factors which vary with each application.
These factors, together with the effects of abrasion,
corrosion, prior use or abuse and any other variables of a
specific application, must be considered by the user and
the grip replaced as appropriate. Where the conditions of
the application are not well defined or known or where risk
of injury to persons or property is involved, a greater safety
factor should be utilized.
Any warranty as to quality, performance or fitness for
use of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored, handled,
used, maintained and inspected by the user at a frequency
appropriate for the use and condition of the grip.
For grip applications on materials other than those that the
grips have been specifically designed for, consult the factory.
Safety And Working Load Factors For Wire Mesh Grips
Select the Correct Fiber Optic Grip
Each Kellems grip is designed to work on a specific range
of cable diameters.
Step 1 Determine your cable outside diameter.
Step 2 Find the grip size that encompasses your cable diameter.
Step 3 Whenever possible, use a closed mesh that assembles
over the cable end. If the cable end is not available, use
a split mesh.
Step 4 Where available, select an eye style that suits your needs.
Step 5 Estimate the tension to be put on the grip, establish the
working load you require and compare this to the listed
approximate breaking strength of the grip to insure that
the grip will be strong enough.
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling grips,
and ten for catalog listed support grips.
www.hubbell-wiring.comV-52 Wiring Device-Kellems
®
How to Select OPTISOK®
• Identify connector bundle diameter to be inserted into
the OPTISOK®.
• Choose appropriate catalog number based on size range.
Installation Information
Step 1 Expand open end of OPTISOK® and gently work in fiber optic
connector bundle.
Step 2 Still gently, work connector bundle up to the forward section
of the OPTISOK®.
Step 3 Starting at approximately 6" (15.2cm) from tail end of OPTISOK®,
tightly fold over the OPTISOK® around cables and tape wrapped
section 3" (7.62cm) past tail end onto the bundle.
Step 4 Securely attach pulling line or tape to pulling ring.
Note: To remove OPTISOK® carefully unwrap tape and slide out cables and connectors or cut
OPTISOK® away without damaging connectors or cables.
Kellems® Wire Management Products
Technical Information
OPTISOK® Pulling Grips
Kellems offers a unique and simple to use tool for the
installation of preconnectorized fiber optic cables, jumpers
and bundles of twisted pair communication cables - the
OPTISOK®.
The OPTISOK® is a highly flexible and expandable
nonmetallic sleeve open on one end and with a pulling
ring on the other. It will expand to enclose the larger group
of fiber optic connectors and grab the cable below the
connector bundle by wrapping and taping to provide a
gripping tool that will grab the cable(s) below the connectors.
The pulling ring can be attached to a pulling line or fish tape
and the OPTISOK® will act as the pulling tool.
OPTISOK® will contain and protect the connector bundle
and save time and labor by making the pulling job easier,
protecting the connectors from possible damage during the
pull and facilitating the passage of the connector bundle
through cramped and tight spaces. The OPTISOK® can be
used to pull cables through plenums, underfloor duct, office
partitions, raised access floors and conduits. Three sizes are
available for all applications.
Step 1
Step 2
Step 3
Step 4
V-53www.hubbell-wiring.com Wiring Device-Kellems
®
Pulling Grip for Loose Tube Fiber Optic Cable
Kellems offers a wire mesh specifically designed to pull loose tube fiber optic cable and meet the special pulling requirements
recommended by fiber optic cable manufacturers.
Many fiber optic cable manufacturers require special cable preparation prior to pulling where a short section of the outer
jacket is stripped off exposing the aramid strength member. This creates two cable diameters, one including the jacket and
a second smaller diameter at the strength member. Kellems fiber grip with its special weave will accommodate and securely
grab both diameters, at the outside jacket and the internal aramid strength member.
Additionally, this galvanized steel mesh grip has longer leads at the pulling eye to facilitate pulling the cable up through the
top, a very low profile lug and eye to slip through tight areas, and short shoulders to protect the cable while maintaining
the slim profile.
The grip can be used to pull cable overhead as well as underground through conduit and duct. It easily mates with a swivel
and has the necessary strength to securely make pulls.
Application Information
• Prior to pulling cable, follow cable manufacturers’ cable preparation recommendations.
• Never exceed cable manufacturers’ pulling tension recommendations.
• Never use grips to approximate breaking strength safety factor of 5 recommended.
Pulling Grips for Other Outside Plant Cables,
Swivel Eye, Flexible Eye, Split Style, Low Profile
Kellems Pulling Grips for fiber optic cable are made of high strength galvanized steel strand. They feature a multiweave mesh,
with one-half the mesh length double weave, and the second half single weave. This special weave provides positive holding
power while allowing the grip to remain flexible with no damage to the cable jacket. Added features include a steel nose cone
which protects the cable end and allows the grip to pass easily through conduit and enclosures. The eye connects easily to a
swivel or a pulling line. Several grip sizes are available to accommodate all diameters of fiber optic cable.
Application
Kellems Flexible Eye Pulling Grips for fiber optic cable are used for the installation of fiber optic communication lines either
underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily
installed on the cable, and are reusable.
Benefits
• High strength multiweave mesh for positive holding power.
• Highly flexible mesh to follow the pulling path of the cable.
• Steel nose cone reduces snags and hang-ups and protects cable end.
• Easily installed and removed.
• A dependable, reusable pulling tool.
Kellems® Wire Management Products
Technical Information
Fiber Optic Pulling Grips
www.hubbell-wiring.comV-54 Wiring Device-Kellems
®
Support Grips for Fiber Optic Cable
Kellems Support Grips for fiber optic cable are specially designed to hold the cable weight as it hangs in a vertical or
horizontal position. Fiber optic cable must be supported and Kellems Grips provide the support easily and economically.
These grips are made of high grade, non-magnetic tin-coated bronze strand. They are offered in universal bale or single eye
configurations and are available in either closed mesh (for use where the cable end is available) or in split mesh, rod closing
(for installation on existing cable runs or at specific locations).
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the mesh pass
around the rod and match up with the strands from the opposite direction. The rod does not touch the cable at any point and
therefore cannot cut the cable. Rod Closing Grips are reusable. They may be removed and reused as many times as desired.
Fast to Install
Step 1 Wrap the grip around the cable and thread the rod through the preformed loops with a corkscrew motion, using the
curved end of the rod to engage the loops.
Step 2 The action required is a steady push and twist simultaneously. The fingers of the left hand are used to bring the loops
together just ahead of the hook on the end of the rod.
Step 3 To remove, simply pull the rod out.
Kellems® Wire Management Products
Technical Information
Fiber Optic Support Grips
V-55www.hubbell-wiring.com Wiring Device-Kellems
®
Types of Attachment
The five attachment methods shown below provide unlimited flexibility
of attachment to meet any condition.
Type E
Double Eye Grip, used where fastening is made with eyebolts or
similar anchor terminations.
Type A
Single Eye Grip, used where fastening MUST be made from one point.
Type U
Universal Bale Grip, used to fasten around a structure or closed eye.
Type Y
Threaded bolt (⁵⁄₁₆-18 x 1½" long), used to fasten through drilled holes
in plate.
Type F
Split fitting to fit AN-818 nuts. Fitting is positioned over nut and located
with internal flange. A hose clamp is furnished and required to hold the
fitting in correct position.
Kellems® Wire Management Products
Hose Containment Grips
Note: It should be emphasized that Kellems® Hose Containment Grips are not to be used as a pressure reinforcing device for hose systems. These grips are custom made.
Consult Technical Services for details.
Kellems Hose Containment Grips are used on high pressure, flexible hose lines to prevent the hose from whipping violently
in the event of hose failure at the fitting. These grips will prevent serious injury to personnel and damage to equipment by
holding the hose in place in the event of hose failure.
Kellems patented Hose Containment Grips are made of stainless steel with double weave mesh construction for high
strength and come complete with hose clamps.
Kellems Hose Containment Grips are supplied in diameters, length and attachments to meet individual requirements.
Contact the Wiring Device-Kellems factory for specific information. These grips help meet OSHA Federal Register 1926-302 (b),
1926-603 (9), (10), JIC H-1-1973 (H13.11) and JIC P-1-1975 (P11.34) requirements.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-41 to V-42.
www.hubbell-wiring.comV-56 Wiring Device-Kellems
®
Strain Relief System Selection Chart
Grip Type Application Features
Cord or Conduit
Range Inches (cm)
Type Fitting or
Attachment Page Number
Deluxe Cord
Aluminum
Fitting/
Stainless
Steel Grip
Outdoors or indoors where
subjected to moisture or
splash. Examples are crane
and hoist pendant drop
stations, hand tools, pumps
and processing equipment.
Aluminum fittings,
stainless steel mesh,
neoprene oil-and-
watertight bushing.
Double-single weave.
.187"-3.250"
(.47-8.25)
NPT, PG, and metric
aluminum, male straight,
45° male, 90° male,
female straight.
Thread sizes ³⁄₈"-3".
V-58, V-59,
V-62
Deluxe Cord
Nylon Fitting/
Stainless
Steel Grip
Outdoors or indoors where
subjected to moisture or
splash. Examples are
marine and food
processing equipment.
Nylon fitting, stainless
steel mesh, double-single
weave, neoprene oil-and-
watertight bushing.
.187"-1.125"
(.47-2.86)
NPT nylon, male straight,
90° male. Thread sizes
½"-1".
V-60
Deluxe Cord
Nylon Fitting/
Non-metallic
Grip
Indoor or outdoors.
Provides liquidtight seal,
where exposed to moisture.
Excellent for oil refining
and chemical processing.
Non-metallic grip is
corrosion resistant,
nonconductive and
provides superior grip-
ping and flexing benefits.
Neoprene liquidtight
bushing. Nylon fitting.
.187"-1.000"
(.47-2.54)
NPT nylon, straight male,
thread sizes ³⁄₈"-1" 90° male,
thread sizes ½"-1".
V-61
Deluxe Cord
Stainless
Steel Fitting
And Grip
Indoor or outdoor use where
exposed to moisture. Very
strong for heavy abuse areas
such as drilling platforms,
steel mills and mines.
Stainless steel fitting
and grip for strength.
Neoprene liquidtight
bushing. Double/single
weave grip.
.187"-1.000"
(.47-2.54)
Straight male
Only with NPT
Thread sizes ½"-1".
V-61
Dust-Tight
Strain Relief
Indoor use only for wiring
of electrical enclosures,
machine tools, portable
power tools, bus drop
cable systems.
Neoprene gasket–seals
out chips, dirt, dust.
One piece design with
galvanized steel mesh.
Insulating bushing available.
Zinc-plated steel locknut.
.240"-2.450"
(.61-6.22)
Straight male NPS
or NPT
V-63
Liquidtight
Flexible
Conduit Grip
(Metal and
Non-Metallic)
Wiring of machine tools,
electrical enclosures, motors
and systems where metallic
liquidtight flexible conduit
is subjected to vibration,
flexure, motion or strain.
Stainless steel mesh,
liquidtight fittings.
Sealing “O" rings
(optional). Choice
of fittings.
.375"-4.000"
trade sizes
NPT ½"-4",
Hubbell fittings,
Male straight,
45° male, 90° male,
female straight.
V-66, V-67
Liquidtight
Flexible
Conduit Grip
(UL Type A)
Wiring or machine tools,
electrical enclosures,
motors and systems
where conduit is subject
to vibration and strain.
Stainless steel mesh,
liquidtight fittings with
“O" ring and locknut.
.375"-2.008"
trade size male
NPT steel,
Hubbell fittings,
straight male, 90°
Thread sizes ½"-2".
V-68
Kellems® Wire Management Products
Strain Relief System Selection Chart
Strain Relief Grips
Kellems Strain Relief Grips are designed to prevent tension
from being transmitted to joints and terminals on electrical
cord, cable and conduit. In most applications, a Kellems
grip for strain relief is stronger than the cable itself and gives
much greater security than the use of a fitting alone. Kellems
Grips for strain relief help make electrical systems safer, and
save money by minimizing downtime from costly electrical
failure due to cable pull-out. Kellems Grips also aid in
compliance with the National Electric Code’s terminal
tension protection requirements.
Select the Correct Grip for Strain Relief
Kellems Grips for strain relief are designed to fit on electrical
cord, cable or flexible conduit.
Step 1 Refer to the chart below to determine the grip style
best suited for your application.
Step 2 Determine your cable outside diameter or conduit size.
Step 3 Locate environment—indoors or outdoors.
Step 4 Decide if a liquidtight seal is required.
Step 5 Select NPT size and fitting style.
V-57www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Strain Relief for Flexible Cords
For Insulated Cables and Flexible, Liquidtight Conduits
Endless weave provides easy cable/flexible conduit installation
Stainless steel mesh is corrosion resistant. Can be used inside or
outside. It eliminates cable or flexible conduit pull out and reduces
costly downtime
Multiweave grip gives cable arc-of-bend control minimizing cable
damage and extending cable life. It is the strongest strain relief
device available. Meets and exceeds all code requirements;
prevents cable/conduit pull-out
A liquidtight fitting is available with both cable and conduit fittings;
prevents liquids from running through the fitting into the enclosure
An NPT and PG threaded body allows easy attachment to either
threaded hub or knock-out in box
www.hubbell-wiring.comV-58 Wiring Device-Kellems
®
Kellems® Wire Management Products
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Straight Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
³⁄₈
.250"-.312"
.312"-.375"
.375"-.437"
(.63-.79)
(.79-.95)
(.9 5 -1.11)
F1
07401001
07401002
07401003
½
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
07401004
07401006
07401008
07401010
½.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 074011247*
074011248*
¾
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
07401011
07401013
07401015
07401017
¾.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 07401018
074011249*
1
.375"-.500"
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.000"
1.000"-1.125"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
F4
074011195
07401019
07401021
07401023
07401025
074011250*
11.125"-1.250"
1.250"-1.375"
(2.86-3.17)
(3.17-3.49) F5 074011028*
074011029*
1¼
.750"-.875"
.875"-1.000"
1.000"-1.125"
1.125"-1.250"
1.250"-1.375"
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
(2.86-3.17)
(3.17-3.49)
F5
074011251
07401026
07401027
07401028
074011178*
1½
.750"-.875"
.875"-1.000"
1.000"-1.125"
1.125"-1.250"
1.250"-1.375"
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
(2.86-3.17)
(3.17-3.49)
F5
074011252
07401029
07401030
07401031
07401032
1½
1.312"-1.437"
1.437"-1.562"
1.562"-1.687"
1.687"- 1.812"
1.750"-1.875"
(3.33-3.65)
(3.65-3.97)
(3.97-4.28)
(4.28-4.60)
(4.44-4.76)
F6
074011253
074011254*
074011255*
074011256*
074011257*
2
1.250"-1.375"
1.312"-1.437"
1.437"-1.562"
1.562"-1.687"
1.687"-1.812"
1.750"- 1.875"
(3.17-3.49)
(3.33-3.65)
(3.65-3.97)
(3.97-4.28)
(4.28-4.60)
(4.44-4.76)
F6
074011258
074011259
07401033
07401034
07401035
074011260
2
1.812"-1.937"
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.60-4.92)
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011261
074011262*
074011263*
074011264*
074011265*
2½
1.688"-1.812"
1.812"-1.937"
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.29-4.60)
(4.60-4.92)
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011030
074011031
074011032
074011033
074011034
074011266*
3
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011036
074011037
074011038
074011039
3
2.437"-2.625"
2.625"-2.812"
2.812"-3.000"
3.000"-3.250"
(6.19-6.67)
(6.67-7.14)
( 7.14 -7.62)
( 7.62- 8 .25 )
F8
074011186
074011187
074011188
074011189*
Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III
Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
*Cable jacket may have to be stripped to pass through connector body.
IMPORTANT
Read all breaking strength, safety
and technical data relating to this
product. Pages V-69 to V-76.
V-59www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Straight Female Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½.375"-.500"
.500"-.625"
(.95-1.27)
(1.27-1.59)
F2 07401043
07401045
¾.500"-.625" (1.27-1.59) F2 07401052
¾.625"-.750" (1.59-1.90) F4 07401053
90° Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
³⁄₈
.250"-.312"
.312"-.375"
.375"-.437"
(.63-.79)
(.79-.95)
(.9 5 -1.11)
F1
07401071
07401072
07401073
½
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
07401074
07401076
07401078
07401080*
¾
.375"-.500"
.500"-.625"
.625"-.750"
.750"-.875"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
F3
07401081
07401083
07401084*
074011275*
1
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.000"
1.000"-1.125"
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
F4
07401085
07401087
07401089
07401091*
074011229*
1¼
.750"-.875"
.875"-1.000"
1.000"-1.125"
1.125"-1.250"
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
(2.86-3.17)
F5
074011230
07401137
07401108
074011042*
1½
1.000"-1.125"
1.125"-1.250"
1.250"-1.375"
(2.54-2.86)
(2.86-3.17)
(3.17-3.49)
F5
074011045
074011046
074011047
2
1.312"-1.437"
1.437"-1.562"
1.687"-1.812"
1.750"-1.875"
(3.33-3.65)
(3.65-3.97)
(4.28-4.60)
(4.44-4.76)
F6
074011233
074011244
074011246
074011234*
45° Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½
.250"-.375"
.375"-.500"
.500"-.625"
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
074011236
074011021
074011237*
¾
.500"-.625"
.625"-.750"
.750"-.875"
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
F3
074011049
074011051*
074011239*
1
.625"-.750"
.750"-.875"
.875"-1.000"
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
F4
074011055
074011057
074011199*
1¼ 1.000"-1.125"
1.125"-1.250"
(2.54-2.86)
(2.86-3.17) F5 074011059
074011060
Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of
the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
*Cable jacket may have to be stripped to pass through connector body.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
www.hubbell-wiring.comV-60 Wiring Device-Kellems
®
Kellems® Wire Management Products
Deluxe Cord Grips
Nylon Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Straight Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
074011331
074011332
074011333
074011334*
¾
.375"-.500"
.500"-.625"
.625"-.750"
.750"-.875"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
F3
074011335
074011336
074011337
074011338*
1
.625"-.750"
.750"-.875"
.875"-1.000"
1.000"-1.125"
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
F4
074011341
074011342
074011343
074011344*
90° Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½
.250"-.375"
.375"-.500"
.500"-.625"
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
074011346
074011347
074011348*
¾
.375"-.500"
.500"-.625"
.625"-.750"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
F3
074011349
074011350
074011351*
Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of
the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
*Cable jacket may have to be stripped to pass through connector body.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
V-61www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Deluxe Cord Grips
Nylon Fittings, Non-metallic Mesh, and Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Nylon Fittings Non-metallic Mesh, Liquidtight for Insulated Cables
Straight Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
³⁄₈
.187"-.250"
.250"-.312"
.312"-.375"
(.47-.63)
(.63-.79)
(.79-.95)
F1
CG304NM
CG305NM
CG306NM
½
.187"-.250"
.250"-.375"
.375"-.500"
(.47-.63)
(.63-.95)
(.95-1.27)
F2
CG404NM
CG406NM
CG408NM
¾
.375"-.500"
.500"-.625"
.625"-.750"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
F3
CG608NM
CG610NM
CG612NM
1
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.000"
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
F4
CG810NM
CG812NM
CG814NM
CG816NM
90° Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½.250"-.375"
.375"-.500"
(.63-.95)
(.95-1.27) F2 CG40690NM
CG40890NM
¾
.375"-.500"
.500"-.625"
.625"-.750"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
F3
CG60890NM
CG61090NM
CG61290NM*
1.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F4 CG81290NM
CG81490NM
Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight for Insulated Cables
Straight Male Thread
NPT Thread
Size Inches
Grip Diameter Range
Inches (cm) Form Size Catalog Number
½
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
CG404SST
CG406SST
CG408SST
CG410SST
¾.375"-.500"
.500"-.625"
(.95-1.27)
(1.27-1.59) F2 CG608SST
CG610SST
¾.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 CG612SST
CG614SST
1
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.000"
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
F4
CG810SST
CG812SST
CG814SST
CG816SST
Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the
National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
*Cable jacket may have to be stripped to pass through connector body.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
www.hubbell-wiring.comV-62 Wiring Device-Kellems
®
Straight PG* Male Thread
Hub Size
Cord Diameter Range
Inches (cm) Form Size Catalog Number
PG16 .500"-.625" (1.27-1.59) F2 074PG16010
PG21 .500"-.625" (1.27-1.59) F2 074PG21010
PG21 .625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 074PG211247
074PG211248
PG29
.625"-.750"
.750"-.875"
.875"-1.000"
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
F4
074PG29021
074PG29023
074PG29025
PG29 1.125"-1.250" (2.86-3.17) F5 074PG291028*
PG36 1.125"-1.250" (2.86-3.17) F5 074PG36028*
Note: *Panzergewinde.
Straight Metric Male Thread
Hub Size
Cord Diameter Range
Inches (cm) Form Size Catalog Number
M20 .500"-.625" (1.27-1.59) F2 074M20010
M25 .625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 074M251247
074M251248
M25 .500"-.625" (1.27-1.59) F2 074M25017
M32
.625"-.750"
.750"-.875"
.875"-1.000"
(1.59-1.90)
(1.90-2.22)
(2.24-2.54)
F4
074M32021
074M32023
074M32025
M32 1.000"-1.125"
1.125"-1.250"
(2.54-2.86)
(2.86-3.17) F5 074M321250
074M321028
Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the
National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
*Cable jacket may have to be stripped to pass through connector body.
Kellems® Wire Management Products
PG and Metric Threaded Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Specifications
Material Temperature Range
Aluminum (Body)
Stainless Steel (Mesh)
Neoprene (Bushings)
–30°F to +240°F (–34°C to +115°C).
–30°F to +240°F (–34°C to +115°C).
–30°F to +240°F (–34°C to +115°C).
Hazardous Locations Suitable for use in hazardous locations per Class I Div. 2,
Class II Div. 1 & 2, Class III Div. 1 & 2 N.E.C.
Reference 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b).
Approvals
Deluxe Cord Grips UL Listed in accordance with Standard 514B for indoor/outdoor use.
UL Control numbers 898D and 899D.
Wet Locations Suitable for use in wet locations when used with a listed sealing ring between box and fitting.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
V-63www.hubbell-wiring.com Wiring Device-Kellems
®
Non-Insulated, Wide Range Strain Relief
Thread Size
Cable Diameter Range
Inches (cm)
Mesh Length
@ Nom. Dia.
Inches (cm) Catalog Number
½ NPT .24"-.32" (.61-.81) 3.25" (8.25) 073031200
½ NPT .32"-.43" (.81-1.0 9) 3.75" (9.52) 073031201
½ NPT .43"-.54" (1.09-1.37) 4.75" (12.06) 073031202
¾ NPT .54"-.73" (1.37-1.85) 6.5" (16.51) 073031203
1 NPT .73"-.97" (1.85-2.46) 7" (17.78) 073031204
1¼ NPT .97"-1.25" ( 2.4 6 -3 .17 ) 9" (22.86) 073031205
PG29* .73"-.97" (1.85-2.46) 7" (17.78 ) 073PG291204
Note: *Panzergewinde.
Insulated, Wide Range Strain Relief with Insulating Bushing
Thread Size
Cable Diameter Range
Inches (cm)
Mesh Length
@ Nom. Dia.
Inches (cm)
Dim. A
Inches (cm)
Min. Space
Between Grips
Inches (cm) Catalog Number
½ NPS .24"-.32" (.61-.81) 3.25" (8.25) 1" (2.54) 1.25" (3.17) 073031206
½ NPS .32"-.43" (.81-1.0 9) 3.75" (9.52) 1" (2.54) 1.25" (3.17) 073031207
½ NPS .43"-.54" (1.09-1.37) 4.75" (12.06) 1" (2.54) 1.25" (3.17) 073031208
¾ NPS .54"-.73" (1.37-1.85) 6.5" (16.51) 1" (2.54) 1.5" (3.81) 073031209
1 NPS .73"-.97" (1.85-2.46) 7 " (17.78 ) 1.313" (3.02) 1.75" (4.44) 073031210
1¼ NPS .97"-1.25" ( 2.4 6 - 3.17 ) 9" (22.86) 1.313" (3.02) 2.25" (5.71) 073031211
1½ NPT 1.25"-1.50" (3.17-3.81) 11.75" (2 9.84) 1.313" (3.02) 2.5" (6.35) 073031212
2 NPT 1.50"-1.70" (3.81-4.32) 13.25" (33.65) 1.375" (3.49) 3.25" (8.25) 073031213
2½ NPT 1.70"-2.00" (4.32-5.08) 13.5" (34.29) 1.5" (3.81) 3.625" (9.21) 073031214
2½ NPT 2.00"-2.45" (5.08-6.22) 13.75" (34.92) 1.5" (3.81) 3.625" (9.21) 073031215
Kellems® Wire Management Products
Dust-Tight Strain Relief Grips
Aluminum Fittings, Galvanized Steel Mesh, for Insulated Cables
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
www.hubbell-wiring.comV-64 Wiring Device-Kellems
®
E
M
Application
Kellems® I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip® plugs and connector bodies. The eye tabs fit
under the nylon cord clamp and the screws slide through the eyelets, securing the grip in place.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs and connector bodies.
• Controls cable arc-of-bend.
• Provides heavy-duty strain relief.
• Fits all sizes.
Kellems® Wire Management Products
I-Grips
Plastic-Coated, Galvanized Steel Mesh for Insulated Cables
I-Grips
Cable Diameter Range
Inches (cm)
E
Inches (cm)
M
Inches (cm) Catalog Number
.32"-.43" (.81-1.09) 1.25" (3.17 ) 4" (10.16) 07310001
.43"-.56" (1.09-1.42) 1.25" (3.17 ) 4.75" (12.06) 07310002
.56"-.73" (1.42-1.85) 1.50" (3.81) 6" (15.24) 07310003
.73"-.85" (1.85-2.16) 1.50" (3.81) 6.5" (16.51) 07310004
.85"-1.00" (2.16-2.54) 1.50" (3.81) 8" (20.32) 07310005
1.00"-1.25" (2.5 4-3.17) 1.50" (3.81) 10" (25.40) 07310006
Note: E-Eye length. M-Mesh length at nominal diameter.
Eyelet hole diameter .203" (.52cm).
I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof covers are to be installed.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-69 to V-76.
V-65www.hubbell-wiring.com Wiring Device-Kellems
®
Thread Adapters for Multi-Pin Connectors
Kellems® Thread Adapters are devices formatting AN-MS
connectors and other multi-pin connectors to Kellems grips
with NPT threaded fittings. They are made of aluminum
with internal threads and replace the connector cord clamp.
These adapters permit the installation of Kellems Grips, to
prevent cable or conduit pull-out and control arc-of-bend.
Applications
Thread adapters allow the installation of Kellems® Grips
on multi-pin connectors at electrical consoles, mobile
equipment, control switches, assembly equipment and
testing machines.
Benefits
• Easy installation.
• Allows the use of Kellems grips.
• Extends connector and cable life.
Kellems® Wire Management Products
Thread Adapters for Multi-Pin Connectors
Aluminum
Thread Adapters for Multi-Pin Connectors
Thread Adapters Deluxe Cord Grips Strain Relief Grips
Liquidtight
Conduit Grips
(Insulated Throat)
AN-MS
Connector
Size**
AN-MS
Cable Clamp
Number***
Thread
Size A
Inch
NPT
Thread
Size B
Catalog
Number
Cable Diameter
Range Inches (cm)
Catalog
Number
Cable Diameter
Range Inches (cm)
Catalog
Number
Catalog
Number
8S, 10S
10SL, 12, 12S
14, 14S
3057-3
3057-4
30 57-6
½" x 28"
⁵⁄₈" x 24"
¾" x 20"
³⁄₈
091041000
091041001
091041002
.250"-.312" (.63-.79)
.312"-.375" (.79-.95)
.375"-.437" (.95-1.11)
07401001
07401002
07401003
— —
14, 14S
16, 16S
18
30 57-6
30 57-8
30 57-10
¾" x 20"
⁷⁄₈" x 20"
1" x 20"
½
091041003
091041004
091041006
.187"-.250" (.47-.63
.250"-.375" (.63-.95)
.375"-.500" (.95-1.27)
.500"-.625" (1.27-1.59)
07401004
07401006
07401008
07401010*
.24"-.32" (.61-.81)
.32"-.43" (.81-1.09)
.43"-.54" (1.09-1.37)
073031200
073031201
073031202
—
0740 93512
—
16, 16S
18
20, 22
30 57-8
30 57-10
30 57-12
⁷⁄₈" x 20"
1" x 20"
1³⁄₁₆" x 18" ¾
091041005
091041007
091041008
.187"-.250" (.47-.63)
.250"-.375" (.63-.95)
.375"-.500" (.95-1.27)
.500"-.625" (1.27-1.59)
.625"-.750" (1.59-1.90)
07401011
07401013
07401015
07401017
07401018
.54"-.74" (1.37-1.85) 073031203 074093513
20, 22
24, 28
32
36
30 57-12
30 57-16
30 57-20
30 57-24
1³⁄₁₆" x 18"
1⁷⁄₁₆" x 18"
1¾" x 18"
2" x 18"
1
091041009
091041010
091041012
091041015
.375"-.500" (.95-1.27)
.500"-.625" (1.27-1.59)
.625"-.750" (1.59-1.90)
.750"-.875" (1.90-2.22)
.875"-1.000" (2.22-2.54)
074011195
07401019
07401021
07401023
07401025
.73"-.97" (1.85-2.46) 073031204 074093514
24, 28
32
36
30 57-16
30 57-20
30 57-24
1⁷⁄₁₆" x 18"
1¾" x 18"
2" x 18"
1¼
091041011
091041013
091041016
.750"-.875" (1.90-2.22)
.875"-1.000" (2.22-2.54)
1.000"-1.125" (2.54-2.86)
1.125"-1.375" (2. 86-3.17)
074011251
07401026
07401027
07401028
.97"-1.25" (2.46-3.17) 073031205 074093515
32
36
40
30 57-20
30 57-24
30 57-28
1¾" x 18"
2" x 18"
2¼" x 16"
1½
091041014
091041017
091041019
.875"-1.000" (2.22-2.54)
1.000"-1.125" (2.54-2.86)
1.125"-1.250" ( 2.8 6 -3.17 )
1.250"-1.375" (3.17-3.49)
07401029
07401030
07401031
07401032
— 074093516
Note: *Cable jacket may have to be stripped to pass through connector body.
**Number stamped on connector shell.
***Number stamped on clamp shell.
Example Thread Adapter
091041006
www.hubbell-wiring.comV-66 Wiring Device-Kellems
®
Benefits
• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff® I Non-Metallic Conduit
Straight With Male Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm)
Catalog Number
(Insulated)
Catalog Number
(Non-insulated)
³⁄₈ ½3" ( 7. 6 2 ) 074093511 074093401
½ ½ 3.5" (8.89) 074093512 074093402
¾¾4" (10.16) 074093513 074093403
115" (12.70) 074093514 074093404
1¼ 1¼ 6" (15.24) 074093515 074093405
1½ 1½ 6.75" (17.14 ) 074093516 074093406
2 2 8" (20.32) 074093518 074093408
2½ 2½ 9.75" (24.76) 074093520 074093410
3311" ( 2 7.9 4 ) 074093522 074093412
4414" (35.56) 074093526 —
90° Angle With Male Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm)
Catalog Number
(Insulated)
Catalog Number
(Non-insulated)
³⁄₈ ½ 3" ( 7. 6 2 ) 074093541 074093421
½ ½ 3.5" (8.89) 074093542 074093422
¾¾4" (10.16) 074093543 074093423
115" (12.70) 074093544 074093424
1¼ 1¼ 6" (15.24) 074093545 074093425
1½ 1½ 6.75" (17.14 ) 074093546 074093426
2 2 8" (20.32) 074093548 074093428
2½ 2½ 9.75" (24.76) 074093550 —
3311" ( 2 7.9 4 ) 074093552 —
Note: For use with Liquidtight Metal conduit and PolyTuff® I Non-Metallic conduit.
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-74 to V-76.
V-67www.hubbell-wiring.com Wiring Device-Kellems
®
Straight With Chase Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm) Catalog Number
½ ½ 3.5" (8.89) 07406079
¾¾4" (10.16) 07406080
115" (12.70) 07406081
1¼ 1¼ 6" (15.24) 07406082
1½ 1½ 6.75" (17.14 ) 07406083
45° Angle With Male Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm)
Catalog Number
(Insulated)
Catalog Number
(Non-insulated)
³⁄₈ ½ 3" ( 7. 6 2 ) 074093561 074093441
½ ½ 3.5" (8.89) 074093562 074093442
¾¾4" (10.16) 074093563 074093443
115" (12.70) 074093564 074093444
1¼ 1¼ 6" (15.24) 074093565 074093445
1½ 1½ 6.75" (17.14 ) 074093566 074093446
2 2 8" (20.32) 074093568 074093448
Note: For use with Liquidtight Metal conduit and PolyTuff® I Non-Metallic conduit.
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff® I Non-Metallic Conduit
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Pages V-74 to V-76.
www.hubbell-wiring.comV-68 Wiring Device-Kellems
®
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for UL Type A Liquidtight Conduit
Straight Male Hubbell Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm) Catalog Number
³⁄₈ ½3.75" (9.52) H038CNK
½½4.5" (11.43) H050CNK
¾¾6.25" (15.87) H075CNK
117.5" (19.05) H100CNK
1¼ 1¼ 9" (22.86) H125CNK
1½ 1½ 13.5" (34.29) H150CNK
2214.5" (36.83) H200CNK
90° Male Hubbell Fitting
Conduit
Trade Size
Inches
NPT
Fitting Size
Inches
Mesh Length
Inches (cm) Catalog Number
³⁄₈ ½3.75" (9.52) H0389CNK
½½4.5" (11.43) H0509CNK
¾¾6.25" (15.87) H0759CNK
117.5" (19.05) H1009CNK
1¼ 1¼ 9" (22.86) H1259CNK
1½ 1½ 13.5" (34.29) H1509CNK
2214.5" (36.83) H2009CNK
IMPORTANT
Read all breaking strength,
safety and technical data
relating to this product.
Page V-76
V-69www.hubbell-wiring.com Wiring Device-Kellems
®
Wire Mesh Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Strain relief grips
• Not subject to continuous outside environment • I-Grips
Stainless steel wire • High strength • Deluxe cord grips
(302/304) • Corrosion resistant • Liquidtight, flexible, metal conduit grips
• Slightly magnetic • UL type A conduit grips
Non-metallic strand • Superior flex life • Non-metallic deluxe cord grips
• Non-conductive
• Corrosion resistant
• Moderate strength
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Operating Temperatures
Material Temperature Range
Aluminum –40°F to +300°F (–40°C to +149°C).
Aluminum Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C).
Non-Metallic Deluxe Cord Grips –30°F to +225°F (–34°C to +107°C).
Nylon –40°F to +225°F (–40°C to +107°C).
Nylon Fitting with Stainless Steel Mesh –40°F to +225°F (–40°C to +107°C).
Stainless Steel –60°F to +1000°F (–51°C to +537°C).
Stainless Steel Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C).
Neoprene (Bushings) –30°F to +240°F (–34°C to +115°C).
Hazardous Locations
Product Categories
The product categories listed to the right are suitable Deluxe cord grip, aluminum fitting;
for use in hazardous locations per Class I Div. 2, Deluxe cord grip, nylon fitting;
Class II Div. 1 & 2, Class III Div. 1 & 2. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Dustight strain relief grips.
Flammability
Non-metallic deluxe cord grips will not support combustion. Listed below are the ratings.
Component Rating
Mesh grip UL 94HB.
Fitting UL 94V-2.
Approvals
UL Listing and CSA Certification are indicated on appropriate product catalog pages.
Agency UL Control Number
Underwriters Laboratories Inc. 898D and 899D.
UL Listed in accordance with Standard 514B for indoor/outdoor use.
Wet Locations
Product Categories
The products noted to the right are suitable Deluxe cord grip, aluminum fitting;
for use in wet locations when a listed sealing Deluxe sealing ring cord grip;
ring is used between box and fitting. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Hubbell non-metallic conduit grips;
Cord connectors;
Hubbell Juniors;
PolyTuff® connectors;
Hubbell sealtite conduit connectors.
www.hubbell-wiring.comV-70 Wiring Device-Kellems
®
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Form Size Definition
The term “Form Size” refers to the physical mass or overall dimensions of a cord connector. Form 1 is the smallest size,
Form 8 is the largest size.
Knockout Holes
NPT
Hub Size Knockout Hole Recommended
Inches Min. to Max. Inches (cm)
¼ .540" to .570" (1.37-1.45)
³⁄₈ .671" to .701" (1.70-1.78)
½ .859" to .906" (2.18-2.30)
¾ 1.094" to 1.141" (2.78-2.90)
1 1.359" to 1.406" (3.45-3.57)
1¼ 1.719" to 1.766" (4.37-4.49)
1½ 1.969" to 2.016" (5.00-5.12)
2 2.453" to 2.500" (6.23-6.35)
2½ 2.953" to 3.000" ( 7. 5 0 -7. 6 2 )
3 3.578" to 3.625" (9.09-9.21)
Product Data
Deluxe Cord Grips, Liquidtight for Insulated Cables
Deluxe Cord Grips helps to alleviate pull tension on terminals, control cable arc-of-bend, prevent cord pull-out, and provide
a liquidtight seal. They are offered with either aluminum, stainless steel or nylon fittings in a variety of configurations and NPT
thread sizes. Additionally, a completely non-metallic product is offered on page V-61.
Application
Deluxe Cord Grips are used indoors or outdoors to help prevent cord pull-out, and where cables are subjected to moisture,
splash or submersion. Specific uses are: wiring enclosures, pendant stations, hand tools, construction, processing and
material handling equipment, pumps, motors and machine tools.
Benefits
• Helps to prevent cable pull-out.
• Controls cable arc-of-bend.
• Provides a liquidtight seal.
• Corrosion resistant stainless steel mesh with aluminum collar.
V-71www.hubbell-wiring.com Wiring Device-Kellems
®
A
(Overall)
B Ref.
C
D
F
E
Deluxe Cord Grips Fitting Dimensions
Straight Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm) Stainless Steel, Inches (cm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
EA
Dia.
B
Ref.
C
D
Throat
Dia.
E A B
Ref.
C
D
Throat
Dia.
E
A/C* A/F* A/C* A/F* A/C* A/F* A/C* A/F*
³⁄₈-18 1.88"
(2.24)
.90"
(2.29)
.46"
(1.17)
.44"
(1.12)
.99"
(2.51)
.88"
(2.24)
1.00"
(2.54)
1.10"
(2.79)
.43"
(1.09)
.45"
(1.14)
1.00"
(2.54)
.93"
(2.36)
1.01"
(2.57)
.88"
(2.24)
.90"
(2.29)
.46"
(1.17)
.45"
(1.14)
.87"
(2.21)
.75"
(1.90)
½-14 1.88"
(2.24)
.90"
(2.29)
.46"
(1.17)
.44"
(1.12)
.99"
(2.51)
.88"
(2.24)
1.00"
(2.54)
1.10"
(2.79)
.43"
(1.09)
.45"
(1.14)
1.00"
(2.54)
.93"
(2.36)
———————
½-14 21.13"
(2.87)
1.10"
(2.79)
.55"
(1.40)
.64"
(1.63)
1.11"
(2.82)
1.00"
(2.54)
1.32"
(3.35)
1.50"
(3.81)
.53"
(1.35)
.58"
(1.47)
1.25"
(3 .17 )
1.12"
(2.84)
1.30"
(3.30)
1.13"
(2.87)
1.10"
(2.79)
.54"
(1.37)
.63"
(1.60)
1.16"
(2.95)
1.00"
(2.54)
½-14 31.38"
(3.51)
1.50"
(3.81)
.55"
(1.40)
.64"
(1.63)
1.40"
(3.56)
1.25"
(3 .17 )
—————————————
¾-14 21.13"
(2.87)
1.10"
(2.79)
.55"
(1.40)
.64"
(1.63)
1.29"
(3.28)
1.13"
(2.87)
—————————————
¾-14 31.38"
(3.51)
1.50"
(3.81)
.55"
(1.40)
.82"
(2.08)
1.40"
(3.56)
1.25"
(3 .17 )
1.56"
(3.96)
1.60"
(4.06)
.55"
(1.40)
.77"
(1.96)
1.44"
(3.66)
1.31"
(3.33)
1.59"
(4.04)
1.38"
(3.51)
1.30"
(3.30)
.56"
(1.42)
.81"
(2.06)
1.44"
(3.66)
1.25"
(3 .17 )
1-11½ 3————— —————————————
1-11½ 41.75"
(4.44)
1.60"
(4.06)
.71"
(1.80)
1.02"
(2.59)
1.81"
(4.60)
1.62"
(4.11)
1.88"
(4.78)
1.75"
(4.44)
.70"
(1.78)
1.01"
(2.57)
1.84"
(4.67)
1.63"
(4.14)
2.02"
(5.13)
1.75"
(4.44)
1.40"
(3.56)
.70"
(1.78)
1.03"
(2.62)
1.88"
(4.78)
1.63"
(4.14)
1-11½ 52.31"
(5.87)
1.70"
(4.32)
.66"
(1.68)
1.01"
(2.57)
2.28"
(5.79)
2.00"
(5.08)
—————————————
1¼-11½ 52.31"
(5.87)
1.70"
(4.32)
.74"
(1.88)
1.26"
(3.20)
2.28"
(5.79)
2.12"
(5.38)
—————————————
1½ -11 52.31"
(5.87)
1.70"
(4.32)
.74"
(1.88)
1.38"
(3.51)
2.28"
(5.79)
2.12"
(5.38)
—————————————
1½-11½ 63.00"
( 7. 6 2 )
2.20"
(5.59)
.75"
(1.90)
1.50"
(3.81)
2.97"
( 7. 5 4 )
2.75"
(6.98)
—————————————
2-11½ 63.00"
( 7. 6 2 )
2.20"
(5.59)
.80"
(2.03)
1.92"
(4.88)
3.24"
(8.24)
3.00"
( 7. 6 2 )
—————————————
2-11½ 73.85"
(9.78)
2.70"
(6.86)
.88"
(2.24)
1.94"
(4.93)
4.05"
(10.29)
3.75"
(9.52)
—————————————
2½-8 73.85"
(9.78)
2.70"
(6.86)
1.30"
(3.30)
2.32"
(5.89)
4.34"
(11.02)
4.02"
(10.21)
—————————————
2½-8 84.75"
(12.06)
2.70"
(6.86)
1.25"
(3 .17 )
2.38"
(6.05)
4.86"
(12.34)
4.50"
(11.43)
—————————————
3-8 73.85"
(9.78)
2.70"
(6.86)
1.30"
(3.30)
2.54"
(6.45)
4.34"
(11.02)
4.01"
(10.21)
—————————————
3-8 84.50"
(11.43)
2.70"
(6.86)
1.38"
(3.51)
3.00"
( 7. 6 2 )
4.86"
(12.34)
4.50"
(11.43)
—————————————
Note: *A/C— Across Corners; A/F—Across Flats.
Dimensions shown are approximate and
are subject to change without notice.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
www.hubbell-wiring.comV-72 Wiring Device-Kellems
®
Deluxe Cord Grips Fitting Dimensions
45° Hubbell Connectors
Aluminum, Inches (cm)
F
NPT
Inches Form
A
Ref.
B
Ref.
C
D
Throat
Dia.
EG
Dia.
Across
Comers
Across
Flats
½-14 22.00"
(5.08)
1.90"
(4.83)
.550"
(1.40)
.560"
(1.42)
1.270"
(3.23)
1.110 "
(2.79)
1.125"
(2.86)
¾-14 32.30"
(5.84)
2.50"
(6.53)
.560"
(1.42)
.750"
(1.90)
1.480"
(3.76)
1.281"
(3.25)
1.375"
(3.49)
1-11½ 42.60"
(6.60)
2.80"
( 7.11)
.700"
(1.78)
1.000"
(2.54)
1.690"
(4.29)
1.500"
(3.81)
1.750"
(4.44)
1¼-11½ 53.90"
(9.91)
3.90"
(9.91)
.740 "
(1.88)
1.250"
(3 .17 )
2.45"
(6.22)
2.125"
(5.40)
2.310"
(5.87)
1½-11½ 53.90"
(9.91)
3.90"
(9.91)
.740 "
(1.88)
1.500"
(3.81)
2.45"
(6.22)
2.125"
(5.40)
2.310"
(5.87)
Dimensions shown are approximate and
are subject to change without notice.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
90° Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm)
F
NPT
Inches Form
A B
Ref.
C
D
Throat
Dia.
E G
Dia.
A
B
Ref.
C
D
Throat
Dia.
E G
Dia.A/C* A/F* A/C* A/F*
³⁄₈-18 11.27"
(3.23)
2.00"
(5.08)
.460"
(1.17)
.440"
(1.12)
1.15"
(2.92)
1.10"
(2.79)
.875"
(2.22)
———————
½-14 21.56"
(3.96)
2.30"
(5.84)
.500"
(1.27)
.546"
(1.39)
1.30"
(3.30)
1.13"
(2.87)
1.125"
(2.86)
1.41"
(3.58)
2.50"
(6.35)
.550"
(1.40)
.575"
(1.46)
1.23"
(3 .12)
1.12"
(2.82)
1.315"
(3.34)
¾-14 31.79"
(4.55)
2.80"
( 7.11)
.560"
(1.42)
.765"
(1.94)
1.49"
(3.78)
1.31"
(3.33)
1.375"
(3.49)
1.65"
(4.19)
2.81"
( 7.14 )
.560"
(1.42)
.765"
(1.94)
1.42"
(3.61)
1.29"
(3.28)
1.560"
(3.96)
1-11½ 42.08"
(5.28)
3.20"
(8 .13)
.700"
(1.78)
1.000"
(2.54)
1.70"
(4.32)
1.50"
(3.81)
1.750"
(4.44)
1.99"
(5.05)
3.30"
(8.38)
.700"
(1.78)
1.010"
(2.57)
1.82"
(4.62)
1.60"
(4.06)
1.875"
(4.76)
1¼-11½ 53 .18"
(8.08)
4.30"
(10.92)
.730"
(1.85)
1.260"
(3.20)
2.47"
(6.27)
2.15"
(5.46)
2.310"
(5.87)
———————
1½-11½ 53.18"
(8.08)
4.30"
(10.92)
.750"
(1.92)
1.500"
(3.81)
2.47"
(6.27)
2.15"
(5.46)
2.310"
(5.87)
———————
2-11½ 63.51"
(8.92)
5.50"
(13.97)
.800"
(2.03)
1.920"
(4.88)
2.98"
( 7. 57 )
2.78"
( 7. 0 6 )
3.000"
( 7. 6 2 )
———————
Note: *A/C - Across Corners; A/F - Across Flats.
B Ref.
A
Ref.
D
C
E
F
G
B Ref.
A
D
C
E
F
G
V-73www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Dimensions shown are approximate and
are subject to change without notice.
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
F
Product Data
Dust-Tight Strain Relief Grips for Insulated Cables
Kellems® Strain Relief Grips connect flexible cord or bus drop cable to electrical enclosures. For indoor use only, they are
available with either insulated or non-insulated aluminum fittings, and feature single weave, galvanized steel mesh grips with
patented wide range mesh construction. They come with a locknut and a neoprene gasket that provides a dust tight seal.
Application
Used to connect electrical cable to power boxes, cabinets, panel boards, power centers, machine tools and with bus
drop systems.
Benefits
• Helps prevent cord or cable pull-out. • Patented mesh construction.
• Provides a dust tight seal. • One piece design.
• Easy installation.
I-Grips for Insulated Cables
Kellems I-Grips are made of high strength, plastic coated galvanized steel strand. They are offered in six sizes to fit all cable
diameters used with Hubbell Insulgrip® Kellems l-Grips will control cable arc-of-bend and reduce high pull tensions from
being transmitted to the wiring terminals.
Application
Kellems I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip plugs and connector bodies. The eye tabs fit under the nylon cord
clamp and the screws slide through the eyelets, securing the grip in place.
I-Grips can be used on any Insulgrip cord set which requires cable, arc-of-bend control or heavy duty strain relief. Cord sets
used at in-door construction sites or for plant maintenance jobs are examples.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs and • Provides heavy duty strain relief.
connector bodies. • Controls cable arc-of-bend.
• Fits all sizes.
Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof covers are to be installed.
Deluxe Cord Grips Fitting Dimensions
Female Hubbell Connectors
Aluminum, Inches (cm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
E
Across
Comers
Across
Flats
³⁄₈-18 1.88"
(2.24)
1.40"
(3.56)
.560"
(1.42)
.44"
(1.12)
.94"
(2.39)
.81"
(2.06)
½-14 21.13"
(2.87)
1.80"
(4.57)
.560"
(1.42)
.63"
(1.60)
1.15"
(2.92)
1.00"
(2.54)
¾-14 21.13"
(2.87)
2.10"
(5.33)
.750"
(1.90)
.63"
(1.60)
1.44"
(3.66)
1.25"
(3 .17 )
1-11½ 41.75"
(4.44)
2.30"
(5.84)
.880"
(2.24)
1.10"
(2.79)
1.88"
(4.78)
1.63"
(4.14)
1¼-11½ 52.31"
(5.87)
2.80"
( 7.11)
.950"
(2.41)
1.43"
(3.63)
2.64"
(6.71)
2.29"
(5.82)
1½-11½ 52.31"
(5.87)
2.80"
( 7.11)
.950"
(2.41)
1.43"
(3.63)
2.64"
(6.71)
2.29"
(5.82)
www.hubbell-wiring.comV-74 Wiring Device-Kellems
®
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Strain Relief Grips for Liquidtight Flexible Metal and PolyTuff® I Non-Metallic Conduit
Kellems Liquidtight, Flexible Metal Conduit Grips are offered with high quality Hubbell plated steel fittings in a wide variety of
NPT sizes and configurations, either insulated or non-insulated. The addition of a stainless steel mesh to these fittings makes
them stronger than the conduit itself. Kellems Conduit Grips helps prevent conduit pull-out from the connecting fitting that
is subject to stress, pull tension, vibration, motion or strain. They promote safe electrical systems and reduce equipment
downtime.
Application
Kellems Conduit Grips are used in the wiring of machine tools, motors, molding equipment, transformers, weaving and
paper machines, fans, lighting, bakeries, breweries, food processing, chemical plants, dairies, mines and any application that
requires Liquidtight Conduit.
Benefits
• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
• Liquidtight fittings.
• Easily installed.
• Stainless steel grip resists corrosion.
Kellems Conduit Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of
the National Electric Code.
Hardened Steel Locknut
has tangs that dig into box
for excellent continuity of
ground; locknut will not slip
or spin
Connectors with insulated throats protect
insulation on wires during wire pulling.
Yellow color easily seen by inspectors.
2½" - 4" sizes include insulating bushing
instead of fixed insulator
Steel grounding ferrule easily
threaded by hand. Fits convolutions
to conduit. Eliminates pullouts and
insures continuity of ground;
distortion free to remain reusable
Nylon gland ring is split for ease of installation
and greater compression. Reversible design
cannot be installed facing the wrong way. Nylon
is impervious to liquids, resistant to temperature
extremes and resists abrasion
Hexagonal compression nut is
screw machined steel through
1" and malleable iron on
larger sizes
Optional Sealing Washer gives
better liquidtight protection
around knockout of sheet metal
box. Neoprene gasket seals out
liquids and steel retaining ring
protects gasket from distortion;
order separately
Body is virtually unbreakable.
Straight connectors through 1" are
screw machine steel; other sizes
malleable iron. Threads at left are
tapered to insure liquidtight seal in
threaded hub. Liquidtight conduit
cutaway view shows flexible steel
core under plastic jacket
Wire mesh grip
prevents pullout
Liquidtight conduit cutaway
view shows flexible steel core
under plastic jacket
V-75www.hubbell-wiring.com Wiring Device-Kellems
®
45° Angle with Male Fitting with Insulated Throat
Dimensions, Inches
Trade
Size
Inches
H J
Ref.
K LM
Throat
Dia.
NCatalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.25" 1.28" .66" 1.20" 1.0 6" .57" 1.16" 1.02" 074093561
½1.25" 1.28" .66" 1.34" 1.19 " .57" 1.21" 1.06" 074093562
¾1.25" 1.44" .66" 1.55" 1.45" .78" 1.50" 1.32" 074093563
11.44" 1.53" .72" 1.95" 1.69" .98" 1.82" 1.59" 074093564
1¼ 1.48" 1.69" .69" 2.39" 2.06" 1.29" 2.32" 2.03" 074093565
1½ 1.72" 2.00" .72" 2.72" 2.38" 1.53" 2.62" 2.29" 074093566
21.75" 2.25" .72" 3.08" 2.87" 1.95" 3.21" 2.80" 074093568
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Dimensions shown are approximate and
are subject to change without notice.
Note: *A/C - Across Corners; A/F - Across Flats.
J
M
Throat
Dia.
L
K
H
N
A/C A/F
D
Throa
t
Dia.
E
A/C A/F
C
A
Ref.
B
Ref.
G
O
Throat
Dia.
E
D
F
P
A/C A/F
90° Angle with Male Fitting
Dimensions, Inches
Trade
Size
Inches
D E
F G
Ref.
O
Throat
Dia.
P
Catalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.31" .59" 1.20" 1.06" 1.44" .60" 1.13" .99" 074093421
½1.31" .59" 1.34" 1.12 " 1.44" .61" 1.21" 1.00" 074093422
¾1.44" .59" 1.55" 1.45" 1.63" .83" 1.48" 1.29" 074093423
11.78" .66" 1.95" 1.60" 2.19" 1.05" 1.80" 1.57" 074093424
1¼ 1.97" .63" 2.39" 2.06" 2.50" 1.37" 2.32" 2.02" 074093425
1½ 2.19" .66" 2.72" 2.38" 2.69" 1.61" 2.58" 2.25" 074093426
22.53" .66" 3.08" 2.87" 3.25" 2.05" 3 .14" 2.75" 074093428
45° Angle with Male Fitting
Dimensions, Inches
Trade
Size
Inches
H J
Ref.
K L M
Throat
Dia.
N
Catalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.19" 1.28" .59" 1.20" 1.06" .60" 1.16" 1.02" 074093441
½1.19" 1.28" .59" 1.34" 1.19" .61" 1.21" 1.06" 074093442
¾1.19" 1.43" .59" 1.55" 1.45" .84" 1.50" 1.32" 074093443
11.38" 1.53" .66" 1.95" 1.69" 1.05" 1.82" 1.59" 074093444
1¼ 1.42" 1.69" .63" 2.39" 2.06" 1.37" 2.32" 2.03" 074093445
1½ 1.66" 2.00" .66" 2.72" 2.38" 1.60" 2.62" 2.29" 074093446
21.69" 2.25" .66" 3.08" 2.88" 2.05" 3.21" 2.80" 074093448
Liquidtight Conduit Grip Fitting Dimensions, Inches
Straight with Male Fitting
Dimensions, Inches
Trade
Size
Inches
A
Ref.
B
Ref.
C D
Throat
Dia.
E
Catalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.43" .59" 1.20" 1.06" .61" 1.07" .93" 074093401
½1.43" .59" 1.34" 1.19" .61" 1.22" 1.06" 074093402
¾1.56" .59" 1.55" 1.37" .84" 1.43" 1.25" 074093403
11.68" .66" 1.95" 1.69" 1.06" 1.73" 1.56" 074093404
1¼ 2.03" .63" 2.39" 2.06" 1.37" 2.36" 2.08" 074093405
1½ 2.21" .63" 2.72" 2.38" 1.53" 2.79" 2.48" 074093406
22.28" .69" 3.08" 2.87" 2.06" 3.32" 2.90" 074093408
Straight with Male Fitting with Insulated Throat
Dimensions, Inches
Trade
Size
Inches
A
Ref.
B
Ref.
C D
Throat
Dia.
E
Catalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.50" .66" 1.20" 1.06" .57" 1.07" .93" 074093511
½1.50" .66" 1.34" 1.19" .57" 1.22" 1.06" 074093512
¾1.62" .66" 1.55" 1.38" .78" 1.43" 1.25" 074093513
11.75" .72" 1.95" 1.69" .98" 1.73" 1.56" 074093514
1¼ 2.09" .69" 2.39" 2.06" 1.29" 2.36" 2.08" 074093515
1½ 2.28" .69" 2.72" 2.37" 1.53" 2.79" 2.48" 074093516
22.34" .75" 3.08" 2.87" 1.95" 3.32" 2.90" 074093518
2½ 3.56" 1.06" 3.92" 3.62" 2.42" 3.85" 3.60" 074093520
33.81" 1.06" 4.70" 4.31" 3.01" 4.65" 4.33" 074093522
43.81" 1.06" 5.75" 5.31" 3.96" 5.75" 5.39" 074093526
90° Angle with Male Fitting with Insulated Throat
Dimensions, Inches
Trade
Size
Inches
D E
F G
Ref.
O
Throat
Dia.
P
Catalog
NumberA/C* A/F* A/C* A/F*
³⁄₈ 1.38" .66" 1.20" 1.06" 1.44" .60" 1.13" .99" 074093541
½1.38" .66" 1.34" 1.12" 1.44" .57" 1.21" 1.00" 074093542
¾1.50" .66" 1.55" 1.45" 1.63" .78" 1.48" 1.29" 074093543
11.84" .66" 1.95" 1.60" 2.19" .98" 1.80" 1.57" 074093544
1¼ 2.03" .69" 2.39" 2.06" 2.50" 1.29" 2.32" 2.02" 074093545
1½ 2.25" .69" 2.72" 2.38" 2.69" 1.53" 2.58" 2.20" 074093546
22.59" .72" 3.08" 2.87" 3.25" 1.95" 3.14" 2.75" 074093548
2½ 3.44" 1.00" 3.92" 3.63" 4.25" 2.42" 3.78" 3.50" 074093550
33.75" 1.00" 4.70" 4.31" 4.87" 3.01" 4.64" 4.30" 074093552
www.hubbell-wiring.comV-76 Wiring Device-Kellems
®
Dimensional Charts For UL Type A, Liquidtight Conduit Grip Fittings
Straight with Male Fitting with Insulated Throat
Dimensions Inches (cm)
Trade Size
NPT Inches A B C D Catalog Number
³⁄₈ 1.922" (4.88) .594" (1.51) 1.156" (2.94) 3.75" (9.52) H038CNK
½1.922" (4.88) .594" (1.51) 1.250" (3.17) 4.50" (11.43) H050CNK
¾2.016" (5.12) .594" (1.51) 1.500" (3.81) 6.25" (15.87) H075CNK
12.157" (5.48) .719" (1.83) 1.844" (4.68) 7.5 0 " (19 .05) H100CNK
1¼ 2.219" (5.64) .750" (1.91) 2.312" (5.87) 9.00" (22.86) H125CNK
1½ 2.344" (5.95) .750" (1.91) 2.578" (6.55) 13.50" (34.29) H150CNK
2 2.406" (6.11) .750" (1.91) 3.187" (8.09) 14.50" (36.83) H200CNK
90° Angle with Male Fitting with Insulated Throat
Dimensions Inches (cm)
Trade Size
NPT Inches E F G H I Catalog Number
³⁄₈ 1.250" (3.18) .594" (1.51) 1.156" (2.9 4) 1.453" (3.69) 3.75" (9.52) H0389CNK
½ 1.281" (3.25) .594" (1.51) 1.250" (3.17) 1.453" (3.69) 4.50" (11.43) H0509CNK
¾ 1.438" (3.65) .594" (1.51) 1.500" (3.81) 1.000" (2.54) 6.25" (15.87) H0759CNK
11.750" (4.44) .719" (1.83) 1.844" (4.68) 2.125" (5.40) 7.5 0 " (19 .05) H1009CNK
1¼ 1.969" (5.00) .750" (1.91) 2.312" (5.87) 2.344" (5.95) 9.00" (22.86) H1259CNK
1½ 2.250" (5.71) .750" (1.91) 2.578" (6.55) 2.500" (6.35) 13.50" (34.29) H1509CNK
2 2.531" (6.43) .750" (1.91) 3.187" (8.09) 2.781" ( 7. 0 6 ) 14.50" (36.83) H2009CNK
C
Flats
A
Ref.
B
Ref.
D
H
I
F
E
G
Flats
Steel Locknut has tangs that dig
into box for excellent continuity of
ground; locknut will not slip or spin
Insulated throat protects
insulation on wires during
pulling; yellow color easily
seen by inspectors
Body is virtually unbreakable. Straight connectors through 1" are screw
machine steel; other sizes are malleable iron. Threads are tapered to
insure liquidtight seal when used in threaded hub; octagonal shape inside
holds the ferrule to prevent conduit from twisting during installation
Neoprene O-ring is factory
assembled into the body
to seal out liquids Wire mesh grip
prevents pullout
Yellow nylon ferrule fits inside non-
metallic conduit to hold the shape; barb
in designed to assure liquidtight seal even
with non-square cut; ferrule is keyed to fit
into body to prevent conduit twisting
Hexagonal compression nut is machine steel
through 1" malleable iron on larger sizes;
tapered interior compresses sleeve over conduit
sealing out liquids and preventing pullout
Yellow nylon sleeve installs over conduit; six slits in sleeve permit
tight compression onto conduit as compression nut is tightened
Strain Relief for UL Type A, Flexible, Liquidtight Conduit
Kellems Grips for UL Type A, non-metallic, flexible, liquidtight conduit are available in straight and 90° male and feature a
high quality Hubbell plated steel or malleable iron fitting, complete with a sealing O-ring, lock nut and stainless steel mesh.
These grips increase the retention of the conduit in the fitting, control its arc-of-bend and provide a liquidtight seal.
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Benefits
• Provides a liquidtight seal.
• Helps prevent conduit pull-out.
• Reduces conduit cutting, kinking, fraying and splitting at the fitting.
• Easily installed.
Application
These grips are used on UL Type A non-metallic
conduit connections at limit switches, motor boxes,
panel boards, control stations and on all types of
machinery and machine tools.
V-77www.hubbell-wiring.com Wiring Device-Kellems
®
Hubbell has the broadest line and the widest choice of
materials in the industry. NPT hub sizes from ¼" to 3" in
straight male end, 90°, 45°, female and underground feed
connectors. They are available in your choice of aluminum,
plated steel, nylon and stainless steel.
Hubbell offers a full line of machined aluminum cord
connectors in NPT hub sizes ¼" through 1" and cast
aluminum 1" to 3". They provide durable performance and a
clean attractive look without adding unwanted weight. NPT
hub sizes ¼" to 1" feature an attractive knurled finish which
makes them easy to handle and maintain a U.L. listing by
hand tightening.
The zinc-plated steel cord connectors offers the strength
of steel and the corrosion resistance of zinc-plating. These
heavy-duty connectors hold up to most manufacturing
chemicals including acid solutions, solvents and other
corrosive materials.
Their machined steel nut and body allows for tightening
the compression nut and NPT hub without worrying about
stripping the threads. For larger size cord, NPT hub sizes
1" to 2", Hubbell utilizes malleable iron connectors which
provide excellent holding and liquidtight performance.
Hubbell’s nylon cord connectors resist most common
industrial corrosives and provide highly effective pullout
protection in a lightweight design. They are ideal for any
application where weight, conductivity or corrosion may
be an issue. They’re available in NPT hub sizes from
¼" to 1".
Stainless steel cord connectors provide superior strength
and corrosion resistance for industrial and military
applications. They are machined from 300 series stainless
steel and come in ¼" to 1", NPT hub sizes.
Kellems® Wire Management Products
Cord Connectors
Features and Benefits
Lubricated neoprene bushing compresses
easily for a liquidtight seal and added
pull-out protection
The connector body is a one-piece design
with machined threads; a tapered interior
seats the bushing evenly for a liquidtight seal
Machined threads provide a strong positive seal;
the tapered interior dome easily drives the
bushing into the connector body
The patented GOTCHA® ring incorporates a
split hinge design to prevent friction and
provide strain relief, also color-coded
for sizing identification
www.hubbell-wiring.comV-78 Wiring Device-Kellems
®
Machined
Aluminum
Machined
Zinc-Plated Steel
Stainless
Steel
Gray Nylon
Black Nylon
Straight Male
NPT
Hub
Size
Cord Dia.
Inches
(mm)
Form
Size
Color
Code
Machined
Aluminum
Machined
Zinc-Plated
Steel
Stainless
Steel
Nylon
Gray
Nylon
Black
¼
.0 6"-.13 "
(1.6-3.2)
.13"-.19"
(3.2-4.7)
.19"-.25"
(4.7- 6.3)
.25"-.31"
(6.3-7.9)
.31"-.38"
( 7. 9 - 9 . 5 )
.38"-.44"
(9.5 -11)
F1
Green
Orange
Red
Black
White
Blue
—
SHC1002
SHC1003
SHC1004
SHC1005**
—
—
—
—
—
—
—
—
—
SHC1003SS
SHC1004SS
—
—
SHC1001CR
SHC1002CR
SHC1003CR
SHC1004CR
SHC1005CR
SHC1006CR
—
—
—
—
SHC2005CR
—
³⁄₈
.0 6"-.13 "
(1.6-3.2)
.13"-.19"
(3.2-4.7)
.19"-.25"
(4.7- 6.3)
.25"-.31"
(6.3-7.9)
.31"-.38"
( 7. 9 - 9 . 5 )
.38"-.44"
(9.5 -11.0)
F1
Green
Orange
Red
Black
White
Blue
SHC1007
SHC1008
SHC1009
SHC1010
SHC1011
SHC1012
—
SHC1008ZP
—
SHC1010ZP
—
SHC1012ZP
—
—
SHC1009SS
—
SHC1011SS
SHC1012SS
—
SHC1008CR
SHC1009CR
SHC1010CR
SHC1011CR
SHC1012CR
—
SHC2008CR
—
SHC2010CR
SHC2011CR
SHC2012CR
½
.19"-.25"
(4.7- 6.3)
.25"-.31"
(6.3-7.9)
.31"-.38"
( 7. 9 - 9 . 5 )
.38"-.44"
(9.5 -11.0)
F1
Red
Black
White
Blue
SHC1015
SHC1016
SHC1017
SHC1018
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
½
.0 6"-.13 "
(1.6-3.2)
.13"-.19"
(3.2-.4.7)
.19"-.25"
(4.7- 6.3)
.25"-.38"
(6.3-.9.7)
.38"-.50"
(9.7-12.7)
.50"-.63"
(12.7-15.9)
F2
Green
Orange
Red
White
Blue
Brown
SHC1019
SHC1020
SHC1021
SHC1022
SHC1023
SHC1024
—
SHC1020ZP
SHC1021ZP
SHC1022ZP
SHC1023ZP
SHC1024ZP
—
SHC1020SS
SHC1021SS
SHC1022SS
SHC1023SS
SHC1024SS
SHC1019CR
SHC1020CR
SHC1021CR
SHC1022CR
SHC1023CR
SHC1024CR**
—
—
SHC2021CR
SHC2022CR
SHC2023CR
SHC2024CR**
½
.38"-.50"
(9.7-12.7)
.50"-.63"
(12.7-15.9)
.63"-.75"
(15.9-19.0)
.75"-.88"
(19.0-22.2)
F3
Blue
Brown
Yellow
Orchid
SHC1025
SHC1026
SHC1027**
SHC1028**
—
—
SHC1027ZP**
SHC1028ZP**
—
—
—
—
—
—
—
—
—
—
—
—
Note:
See pages V-87 to V-95 for technical information and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information.
**Cable jacket may have to be stripped to pass through connector body.
Locknuts sold separately. See page V-84 for additional information.
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 1-3
IP66*
SUITABILITY
UL Listed to
Type 4, 4X, 12 and 13
V-79www.hubbell-wiring.com Wiring Device-Kellems
®
Straight Male
NPT
Hub
Size
Cord Dia.
Inches
(mm)
Form
Size
Color
Code
Machined
Aluminum
Machined
Zinc-Plated
Steel
Stainless
Steel
Nylon
Gray
Nylon
Black
¾
.0 6 "-.13"
(1.6-3.2)
.13"-.19"
(3.2-4.7)
.19"-.25"
(4.7- 6.3)
.25"-.38"
(6.3-9.7)
.38"-.50"
(9.7-12.7)
.50"-.63"
(12.7-15.9)
F2
Green
Orange
Red
White
Blue
Brown
SHC1029
SHC1030
SHC1031
SHC1032
SHC1033
SHC1034
—
SHC1030ZP
SHC1031ZP
SHC1032ZP
SHC1033ZP
SHC1034ZP
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
¾
.38"-.50"
(9.5 -12.7)
.50"-.63"
(12.7-15.9)
.63"-.75"
(15.9-19.0)
.75"-.88"
(19.0-22.2)
F3
Blue
Brown
Yellow
Orchid
—
SHC1036
SHC1037
SHC1038**
SHC1035ZP
—
SHC1037ZP
SHC1038ZP**
SHC1035SS
SHC1036SS
SHC1037SS
SHC1038SS**
SHC1035CR
SHC1036CR
SHC1037CR
SHC1038CR**
SHC2035CR
SHC2036CR
SHC2037CR
SHC2038CR**
1
.50"-.63"
(12.7-15.9)
.63"-.75"
(15.9-19.0)
.75"-.88"
(19.0-22.2)
F3
Brown
Yellow
Orchid
—
—
—
SHC1097ZP
SHC1098ZP
SHC1099ZP
—
—
—
—
—
—
—
—
—
1
.38"-.50"
(9.7-12.7)
.50"-.63"
(12.7-15.9)
.63"-.75"
(15.9-19.0)
.75"-.88"
(19.0-22.2)
.88"-1.00"
(22.2-25.4)
1.00"-1.13"
(25.4-28.6)
F4
Blue
Brown
Yellow
Orchid
Gray
Pink
SHC1039
SHC1040
SHC1041
SHC1042
SHC1043
SHC1044**
—
—
—
—
SHC1043ZP
—
—
—
SHC1041SS
SHC1042SS
SHC1043SS
SHC1044SS**
SHC1039CR
SHC1040CR
SHC1041CR
SHC1042CR
SHC1043CR
SHC1044CR**
—
SHC2040CR
SHC2041CR
SHC2042CR
SHC2043CR
SHC2044CR**
Note:
See pages V-87 to V-95 for technical information and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information.
**Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
Locknuts sold separately. See page V-84 for additional information.
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 2-4
IP66*
SUITABILITY
UL Listed to
Type 4, 4X, 12 and 13
Machined
Aluminum
Machined
Zinc-Plated Steel
Stainless
Steel
Gray Nylon
Black Nylon
www.hubbell-wiring.comV-80 Wiring Device-Kellems
®
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 5-8
UL Listed to
Type 4, 4X, 12 and 13
Cast Aluminum
Cast Aluminum
Malleable Iron
Straight Male
NPT
Hub
Size
Cord Diameter
Inches (mm)
Form
Size Cast Aluminum Malleable Iron
1
.88"-1.00"
1.00"-1.13"
1.13"-1.25"
1.25"-1.38"
(22.2-25.4)
(25.4-28.6)
(28.6-31.7)
(31.7-34.9)
F5
SHC1046
SHC1047**
SHC1048**
SHC1049**
—
—
—
—
1¼
.75"-.88"
.88"-1.00"
1.00"-1.13"
1.13"-1.25"
1.25"-1.38"
(19.0-22.2)
(22.2-25.4)
(25.4-28.6)
(28.6-31.7)
(31.7-34.9)
F5
SHC1050
SHC1051
SHC1052
SHC1053
SHC1054**
—
—
SHC1052ZP
SHC1053ZP
SHC1054ZP
1½
.75"-.88"
.88"-1.00"
1.00"-1.13"
1.13"-1.25"
1.25"-1.38"
(19.0-22.2)
(22.2-25.4)
(25.4-28.6)
(28.6-31.7)
(31.7-34.9)
F5
SHC1055
SHC1056
SHC1057
SHC1058
SHC1059
—
—
SHC1057ZP
SHC1058ZP
SHC1059ZP
1½
1.38"-1.50"
1.50"-1.63"
1.63"-1.75"
1.75"-1.88"
( 34 .9 - 3 8.1)
(38.1-41.3)
(41.3-44.4)
( 4 4 .4 - 4 7.6 )
F6
SHC1061
SHC1062**
SHC1063**
SHC1064**
—
—
—
—
2
1.25"-1.38"
1.38"-1.50"
1.50"-1.63"
1.63"-1.75"
1.75"-1.88"
(31.7-34.9)
( 34 .9 - 3 8.1)
(38.1-41.3)
(41.3-44.4)
( 4 4 .4 - 4 7.6 )
F6
SHC1065
SHC1066
SHC1067
SHC1068
SHC1069
—
—
—
—
—
2
1.69"-1.81"
1.81"-1.94"
1.94"-2.06"
2.06"-2.19"
2.19"-2.31"
(42.9-46.0)
(46.0-49.2)
(49.2-52.4)
(52.4-55.6)
(55.6-58.7)
F7
SHC1070
SHC1071
SHC1072**
SHC1073**
SHC1074**
—
—
—
—
—
2½
1.69"-1.81"
1.81"-1.94"
1.94"-2.06"
2.06"-2.19"
2.19"-2.31"
2.31"-2.44"
(42.9-46.0)
(46.0-49.2)
(49.2-52.4)
(52.4-55.6)
(55.6-58.7)
(58.7- 61.9)
F7
SHC1076
SHC1077
SHC1078
SHC1079
SHC1080
SHC1081**
—
—
—
—
—
—
3
1.69"-1.81"
1.94"-2.06"
2.06"-2.19"
2.19"-2.31"
2.31"-2.44"
(42.9-46.0)
(49.2-52.4)
(52.4-55.6)
(55.6-58.7)
(58.7- 61.9)
F7
SHC1086
SHC1088
SHC1089
SHC1090
SHC1091
—
—
—
—
—
3
2.44"-2.63"
2.63"-2.81"
2.81"-3.00"
3.00"-3.25"
(61.9 -66.7)
(66.7-71.4)
(71.4-76.2)
(76.2-82.5)
F8
SHC1092
SHC1093
SHC1094
SHC1095**
—
—
—
—
Note:
See pages V-87 to V-95 for technical information and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information.
**Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
F5 and larger will not be color coded.
Locknuts sold separately. See page V-84 for additional information.
IP66*
SUITABILITY
V-81www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
45° and 90° Male Cord Connectors
Form Size 1-6
UL Listed to
Type 4, 4X, 12 and 13
45° Male
NPT
Hub
Size
Cord Diameter
Inches (mm)
Form
Size
Color
Code
Machined
Aluminum†
Machined
Zinc-Plated
Steel∆
Cast
Aluminum
½
.19"-.25"
.25"-.38"
.38"-.50"
.50"-.63"
(4.7- 6.3)
(6.3-9.7)
(9.7-12.7)
(12.7-15.9)
F2
Red
White
Blue
Brown
VHC1021
VHC1022
VHC1023
VHC1024**
—
VHC1022ZP
VHC1023ZP
VHC1024ZP**
—
—
—
—
¾
.38"-.50"
.50"-.63"
.63"-.75"
(9.7-12.7)
(12.7-15.9)
(15.9-19.0)
F3
Blue
Brown
Yellow
VHC1035
VHC1036
VHC1037**
—
—
—
—
—
—
1.63"-.75"
.75"-.88"
(15.9-19.0)
(19.0-22.2) F4 Yellow
Orchid
VHC1041
VHC1042
—
—
—
—
1¼ 1.00"-1.13"
1.13"-1.25"
(25.4-28.6)
(28.6-31.7) F5 —
—
—
—
VHC1052
VHC1053**
90° Male
NPT
Hub
Size
Cord Diameter
Inches (mm)
Form
Size
Color
Code
Machined
Aluminum†
Machined
Zinc-Plated
Steel∆
Nylon
Gray
Nylon
Black
Cast
Aluminum
³⁄₈
.25"-.31"
.31"-.38"
.38"-.44"
(6.3-7.9)
( 7. 9 - 9 . 5 )
(9.5 -11.0)
F1
Black
White
Blue
NHC1010
NHC1011
NHC1012
—
—
—
—
—
—
—
—
—
—
—
—
½
.0 6 "-.13"
.13"-.19"
.19"-.25"
.25"-.38"
.38"-.50"
.50"-.63"
(1.6-3.2)
(3.2-4.7)
(4.7- 6.3)
(6.3-9.7)
(9.7-12.7)
(12.7-15.9)
F2
Green
Orange
Red
White
Blue
Brown
—
NHC1020
NHC1021
NHC1022
NHC1023
NHC1024**
—
—
NHC1021ZP
NHC1022ZP
NHC1023ZP
NHC1024ZP**
—
NHC1020CR
NHC1021CR
NHC1022CR
NHC1023CR
NHC1024CR**
—
—
—
NHC2022CR
NHC2023CR
NHC2024CR**
—
—
—
—
—
—
¾
.38"-.50"
.50"-.63"
.63"-.75"
.75"-.88"
(9.7-12.7)
(12.7-15.9)
(15.9-19.0)
(19.0-22.2)
F3
Blue
Brown
Yellow
Orchid
NHC1035
NHC1036
NHC1037
NHC1038
NHC1035ZP
NHC1036ZP
NHC1037ZP
NHC1038ZP
NHC1035CR
NHC1036CR
NHC1037CR
NHC1038CR
—
—
—
—
—
—
—
—
1
.50"-.63"
.63"-.75"
.75"-.88"
.88"-1.00"
1.00"-1.13"
(12.7-15.9)
(15.9-19.0)
(19.0-22.2)
(22.2-25.4)
(25.4-28.7)
F4
Brown
Yellow
Orchid
Gray
Pink
NHC1040
NHC1041
NHC1042
NHC1043**
NHC1044**
—
NHC1041ZP
—
—
—
—
NHC1041CR
NHC1042CR
NHC1043CR
—
—
NHC2041CR
NHC2042CR**
NHC2043CR**
—
—
—
—
—
—
1¼
.88"-1.00"
1.00"-1.13"
1.13"-1.25"
1.25"-1.38"
(22.2-25.4)
(25.4-28.6)
(28.6-31.7)
(31.7-34.9)
F5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NHC1051
NHC1052
NHC1053**
NHC1054**
1½
1.00"-1.13"
1.13"-1.25"
1.25"-1.38"
(25.4-28.6)
(28.6-31.7)
(31.7-34.9)
F5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NHC1057
—
NHC1059
21.38"-1.50" ( 34 .9 - 3 8.1) F6 — — — — — NHC1066
Note:
See pages V-87 to V-95 for technical information and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information.
**Cable jacket may have to be stripped to pass through connector body.
†Nuts are machined aluminum and bodies are cast aluminum.
∆Compression nuts are machined zinc-plated steel and bodies are zinc-plated malleable iron.
Locknuts sold separately. See page V-84 for additional information.
IP66*
SUITABILITY
www.hubbell-wiring.comV-82 Wiring Device-Kellems
®
Machined
Aluminum
Gray Nylon
Machined
Zinc-Plated Steel
Machined
Aluminum
Machined
Aluminum
Straight Female
NPT
Hub
Size
Cord Diameter
Inches (mm)
Form
Size
Color
Code
Machined
Aluminum
½.25"-.38"
.38"-.50"
(6.3-9.7)
(9.7-12.7) F2 White
Blue
FHC1022
FHC1023
¾.38"-.50"
.50"-.63"
(9.7-12.7)
(12.7-15.9) F2 Blue
Brown
FHC1033
FHC1034
1.75"-.88"
.88"-1.00"
(19.0-22.2)
(22.2-25.4) F4 Orchid
Gray
FHC1042†
FHC1043†
Note: See pages V-87 to V-95 for technical information and dimensional drawings.
*Cable jacket may have to be stripped to pass through connector body.
†Nuts are machined aluminum and bodies are cast aluminum.
Underground Feeder Connectors
NPT
Hub
Size
Cord Diameter
Inches (mm)
Wire
Size
UF**
Machined
Aluminum
Machined
Zinc-Plated
Steel
Nylon
Gray
Nylon
Black
½.2"x.4" min
.25"-.55" max
(5.1 x 10.2)
(6.3 x 14.0)
2 # 14,
2 # 12,
2 # 10.
UFC0001 UFC0001ZP UFC0001CR UFC2001CR
¾.2"x.4" min
.25"-.55" max
(5.1x10.2)
(6.3x14.0)
2 # 14,
2 # 12,
2 # 10.
UFC0002 — — —
¾.2"x.6" min
.26"x.78" max
(5.1x15.2)
(6.6x19.8)
3 # 14,
3 # 12,
3 # 10.
UFC0003 — UFC0003CR UFC2003CR
Note: See pages V-87 to V-95 for technical information and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information.
**Wire sizes vary among manufacturers.
Locknuts sold separately
, see page V-84 for additional information.
Metric Aluminum Cord Connectors
Metric
Hub
Size
Cord Diameter
Inches (mm)
Form
Size Catalog Number
M16 .31"-.38" ( 7.9 - 9. 7 ) F1 SHCM161011
M20 .31"-.38" ( 7. 9 - 9. 7 ) F1 SHCM201017
M20
.25"-.38"
.38"-.50"
.50"-.62"
(6.3-9.7)
(9.7-12.7)
(12.7-15.8)
F2
SHCM201022
SHCM201023
SHCM201024
M25 .38"-.50"
.50"-.62"
(9.7-12.7)
(12.7-15.8) F2 SHCM251033
SHCM251034
M30 .63"-75" (15.9-19.0) F3 SHCM301037
Note: †
When used with metal clad O-ring, see page V-84 for additional information.
Non-metallic Locknuts sold separately
, see page V-84 for additional information.
Kellems® Wire Management Products
Straight Female, Underground Feeder and Metric Connectors
Form Size 1-4
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13 †
V-83www.hubbell-wiring.com Wiring Device-Kellems
®
SEC100BA
SECP29GA
LNP29BPK25
Low Profile NPT Cord Connectors
NPT
Hub Size
Cord Diameter
Inches (mm) Color Catalog Number Non-metallic Locknuts
³⁄₈ .18"-.31" (4 . 6 -7. 9 ) Gray SEC38GA* 31622002LPK50
³⁄₈ .18"-.31" (4 . 6 -7. 9 ) Black SEC38BA* 31622002LPK50
½.17"-.45" (4. 3-11.4) Gray SEC50GA 31622003LPK50
½.17"-.45" (4. 3-11.4) Black SEC50BA 31622003LPK50
¾.45"-.71" (11.4-18.0) Gray SEC75GA 31622007LPK50
¾.45"-.71" (11.4-18.0) Black SEC75BA 31622007LPK50
1.59"-1.00" (15-25.4) Gray SEC100GA 31622008LPK50
1.59"-1.00" (15-25.4) Black SEC100BA 31622008LPK50
Note: See pages V-87 to V-95 for technical information and dimensional drawings.
Catalog numbers with “PK50” suffix are bulk packed 50 pieces.
Low Profile PG∆ Cord Connectors
Hub Size
Cord Diameter
Inches (mm) Color Catalog Number Non-metallic Locknuts
PG7 .11"-.25" (2.9-6.4) Gray SECP7GA* LNP7BPK100
PG7 .11"-.25" (2.9-6.4) Black SECP7BA* LNP7BPK10 0
PG9 .18"-.31" ( 4 .6 - 7.9 ) Gray SECP9GA* LNP9BPK10 0
PG9 .18"-.31" ( 4 .6 - 7.9 ) Black SECP9BA* LNP9BPK100
PG11 .23"-.40" (5.8-10.0) Gray SECP11GA* LNP11BPK100
PG11 .23"-.40" (5.8-10.0) Black SECP11BA* LNP11BPK10 0
PG13.5 .17"-.47" (4.3 -11.9) Gray SECP13GA LNP13BPK100
PG13.5 .17"-.47" (4.3 -11.9) Black SECP13BA LNP13BPK100
PG16 .23"-.53" (5.8-13.5) Gray SECP16GA LNP16BPK10 0
PG16 .23"-.53" (5.8-13.5) Black SECP16BA LNP16BPK100
PG21 .45"-.71" (11 .4 -17. 9 ) Gray SECP21GA LNP21BPK100
PG21 .45"-.71" (11 .4 -17. 9 ) Black SECP21BA LNP21BPK100
PG29 .59"-.99" (15-25.2) Gray SECP29GA LNP29BPK25
PG29 .59"-.99" (15-25.2) Black SECP29BA LNP29BPK25
PG36 .88"-1.30" (22.2-32.0) Gray SECP36GA LNP36BPK25
PG36 .88"-1.30" (22.2-32.0) Black SECP36BA LNP36BPK25
Low Profile Metric Cord Connectors
Hub Size
Cord Diameter
Inches (mm) Color Catalog Number Non-metallic Locknuts
M12 .12"-.25" (2.9-6.4) Gray SECM12G LNM12BPK10 0
M12 .12"-.25" (2.9-6.4) Black SECM12B LNM12BPK100
M16 .11"-.31" ( 2 .7-7.9 ) Gray SECM16G LNM16BPK100
M16 .11"-.31" ( 2 .7-7.9 ) Black SECM16B LNM16BPK100
M20 .17"-.45" (4.3 -11.4) Gray SECM20G* LNM20BPK100
M20 .17"-.45" (4.3 -11.4) Black SECM20B* LNM20BPK100
M25 .49"-.71" (12.3 -18.0) Gray SECM25G* LNM25BPK100
M25 .49"-.71" (12.3 -18.0) Black SECM25B* LNM25BPK100
M32 .59"-1.00" (15.0-25.4) Gray SECM32G* LNM32BPK100
M32 .59"-1.00" (15.0-25.4) Black SECM32B* LNM32BPK100
M40 .87"-1.30" (22.0-32.0) Gray SECM40G LNM40BPK100
M40 .87"-1.30" (22.0-32.0) Black SECM40B LNM40BPK100
Note: See pages V-87 to V-96 for technical information and dimensional drawings.
Catalog numbers above with “PK100” suffix, i.e. LNP7BPK100, are bulk packed 100 per carton.
Catalog numbers above with “PK25” suffix, i.e. LNP29BPK25, are bulk packed 25 per carton.
*Items indicated are UL recognized components.
∆Panzergewinde.
Kellems® Wire Management Products
Low Profile NPT, PG and Metric Thread Connectors
Non-Metallic Cord Connectors
IP66*
SUITABILITY
www.hubbell-wiring.comV-84 Wiring Device-Kellems
®
Kellems® Wire Management Products
Accessories
Cord Connector Parts
NPT
Hub Size
Cord Diameter
Inches (mm)
Form
Size
Bushing
Catalog Number Color Code
GOTCHA® Ring
Catalog Number
¼, ³⁄₈, ½
.062"-.125"
.125"-.187"
.187"-.250"
.250"-.312"
.312"-.375"
.375"-.437"
(1.58- 3.17)
(3 .17- 4.76)
(4.76-6.35)
( 6 . 3 5 -7. 9 3 )
( 7. 9 3 - 9 . 5 0 )
( 9.5 0 -11.1)
F1
31518101BPK100
31518102BPK100
31518103BPK100
31518104BPK100
31518105BPK100
31518106BPK100
Green
Orange
Red
Black
White
Blue
31648035GPK100
31648036GPK100
31648037GPK100
31648038GPK100
31605010GPK100
31648039GPK100
½, ¾
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(4.76-6.35)
(6.35-9.50)
(9.50-12.7)
(12.7-15.8)
F2
31518110BPK100
31518111BPK100
31518112BPK100
31518113BPK100
Red
White
Blue
Brown
31648042GPK100
31605015GPK100
31648043GPK100
31648044GPK100
½, ¾
.375"-.500"
.500"-.625"
.625"-.750"
.750"-.875"
(9.50-12.7)
(12.7-15.8)
(15.8-19.0)
(19.0-22.2)
F3
31518116BPK100
31518117BPK100
31518118BPK100
31518119BPK100
Blue
Brown
Yellow
Orchid
31648045GPK100
31648046GPK100
31648047GPK100
31648048GPK100
1
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.00"
1.00"-1.125"
(12.7-15.8)
(15.8-19.0)
(19.0-22.2)
(22.2-25.4)
(25.4-28.5)
F4
31518123BPK100
31518124BPK100
31518125BPK100
31518126BPK100
31518127BPK100
Brown
Yellow
Orchid
Gray
Pink
31648050GPK100
31648051GPK100
31648052GPK100
31648053GPK100
31648054GPK100
Note: Catalog numbers above with “PK100” suffix, i.e. 31518101BPK100, are bulk packed 100 per carton
Locknuts and
Metal Clad Sealing O-Rings
NPT
Hub Size Zinc-Plated Steel Locknuts Non-Metallic Locknuts Metal Clad Sealing O-Rings*
¼
³⁄₈
½
¾
—
—
00322001LPK50
00322002LPK50
31622001LPK50
31622002LPK50
31622003LPK50
31622007LPK50
—
—
20509001
20509002
1
1¼
1½
00322003LPK50
00322004LPK50
00322005LPK50
31622008LPK50
—
—
20509003
20509004
20509005
2
2½
3
—
—
—
—
—
—
20509006
20509007
20509008
Note: Catalog numbers above with “PK50” suffix, i.e. 00322001LPK50, are bulk packed 50 per carton.
See page V-96 for technical information and dimensional drawings.
*UL listed and CSA certified.
Multi-Hole Cord Grip Connectors
NPT
Hub Size
Cord Diameter
Color Holes Catalog NumberInches (mm)
½.205" (5.2mm) Black 2SEC50B252
¾.205" (5.2mm) Black 3SEC75B352
¾.205" (5.2mm) Black 4SEC75B452
½.220" (5.6mm) Black 3SEC50B356
1.215" (5.5mm) Black 9* SEC100BSMH9
1¼ .215" (5.5mm) Black 13* SEC125BSMH13
Note: *Skinned bushings, field configurable.
SEC100BSMH9
V-85www.hubbell-wiring.com Wiring Device-Kellems
®
Hubbell Juniors are a miniature liquidtight version of the
full-sized Hubbell cord connectors. They feature the same
GOTCHA® ring technology and neoprene bushings.
They also come with or without a nylon spiral for arc-of-
bend control and longer cord life. They are available in
¼", ³⁄₈", and ½" NPT sizes in both gray and black.
Kellems® Wire Management Products
Hubbell Juniors® Miniature Connectors
Features and Benefits
Patented GOTCHA® ring incorporates
a split hinge design to prevent friction
and provide strain relief
Lubricated neoprene bushing
compresses evenly for a liquidtight
seal and added pull-out protection
Nylon spiral provides arc-of-bend control
for cord protection
Threaded hexagon shaped nylon
locknut secures tightly and is also
corrosion resistant
Nylon compression nut has a tapered
interior dome to easily drive the
bushing into the connector body
Nylon connector body is a one piece
design with a tapered interior that seals
the bushing evenly for a positive seal
www.hubbell-wiring.comV-86 Wiring Device-Kellems
®
Miniature Nylon Cord Connector
NPT
Hub Size
Cord Diameter Range
Inches (mm) Gray Black
¼
.0 8"-.14"
.14"-.20"
.20"-.27"
(1.9-3.4)
(3 .4-5.1)
( 5.1- 6.7 )
HJ1001GPK25
HJ1002GPK25
HJ1003GPK25
HJ1001BPK25
HJ1002BPK25
HJ1003BPK25
³⁄₈
.15"-.21"
.21"-.28"
.28"-.34"
(3.7-5.3)
(5.3-7.0)
( 7. 0 - 8 . 6 )
HJ1004GPK25
HJ1005GPK25
HJ1006GPK25
HJ1004BPK25
HJ1005BPK25
HJ1006BPK25
½
.0 6 "-.13"
.13"-.19"
.19"-.25"
.25"-.31"
.31"-.38"
.38"-.44"
(1.6-3.2)
(3.2-4.7)
(4.7- 6.3)
(6.3-7.9)
( 7. 9 - 9 . 5 )
(9.5 -11.1)
HJ1055GPK25
HJ1056GPK25
HJ1057GPK25
HJ1058GPK25
HJ1059GPK25
HJ1060GPK25
HJ1055BPK25
HJ1056BPK25
HJ1057BPK25
HJ1058BPK25
HJ1059BPK25
HJ1060BPK25
Miniature Nylon Cord Connector with Spiral
NPT
Hub Size
Cord Diameter Range
Inches (mm) Gray Black
¼
.0 8"-.14"
.14"-.20"
.20"-.27"
(1.9-3.4)
(3 .4-5.1)
( 5.1- 6.7 )
HJ1010GPK25
HJ1011GPK25
HJ1012GPK25
HJ1010BPK25
HJ1011BPK25
HJ1012BPK25
³⁄₈
.15"-.21"
.21"-.28"
.28"-.34"
(3.7-5.3)
(5.3-7.0)
( 7. 0 - 8 . 6 )
HJ1013GPK25
HJ1014GPK25
HJ1015GPK25
HJ1013BPK25
HJ1014BPK25
HJ1015BPK25
½
.13"-.19"
.19"-.25"
.25"-.31"
.31"-.38"
.38"-.44"
(3.2-4.7)
(4.7- 6.3)
(6.3-7.9)
( 7. 9 - 9 . 5 )
(9.5 -11.1)
HJ1038GPK25
HJ1039GPK25
HJ1040GPK25
HJ1041GPK25
HJ1042GPK25
HJ1038BPK25
HJ1039BPK25
HJ1040BPK25
HJ1041BPK25
HJ1042BPK25
¾.25"-.49"
.45"-.71"
(6.4-12.3)
(11.4-18.0)
HJ1043GPK25*
HJ1044GPK25*
HJ1043BPK25*
HJ1044BPK25*
Note: *Locknuts sold separately, see page V-84 for additional information.
Miniature Nylon Snap-In Cord Connector with Spiral
Cord Diameter Range
Inches (mm) For Chassis Thickness Gray Black
.22"-.27" (5.6-6.9) .10" (2.5) Max HS1001GPK25 HS1001BPK25
.28"-.32" (7.1-8.1) .10" (2.5) Max HS1002GPK25 HS1002BPK25
.30"-.36" ( 7. 6 - 9.1) .13" (3.2) Max HS1003GPK25 HS1003BPK25
.32"-.43" (8 .1-10.9 ) .13" (3.2) Max HS1004GPK25 HS1004BPK25
Note: Catalog numbers above with “PK25” suffix, i.e. HJ1001GPK25, are bulk packed 25 per carton.
See page V-97 for technical information and dimensional drawings.
Kellems® Wire Management Products
Hubbell Juniors® Miniature Nylon Cord Connectors
Gray Cord Connector
Black Cord Connector
Gray Cord Connector
with Spiral
Black Cord Connector
with Spiral
Gray Snap-In
Cord Connector
Black Snap-In
Cord Connector
V-87www.hubbell-wiring.com Wiring Device-Kellems
®
Operating Temperatures
Material Temperature Range
Aluminum -40°F to +300°F (-40°C to +149°C)
Nylon (connectors and GOTCHA® rings) -40°F to +225°F (-40°C to +107°C)
Plated steel* -60°F to +1000°F (-51°C to +537°C)
Stainless steel* -60°F to +1000°F (-51°C to +537°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
Note: *Due to the limiting factors of nylon and neoprene, any complete cord connector with a GOTCHA ring, Form 1-5, will continuously perform in the range of -30°F to
+225°F (-34°C to +107°C).
Cord connectors without GOTCHA rings, Form 6-8, will continuously operate in the range -30°F to +240°F (-34°C to +115°C) due to the limiting factor of neoprene.
Hazardous Locations
Hubbell cord connectors are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class Ill Div. 1 & 2 in accordance with the NEC.
Flammability
Hubbell nylon cord connectors have a UL 94-V2 rating.
Approvals
Agency
UL Listed in accordance with Standard 514B for indoor/outdoor use.
CSA Certified.
United States Coast Guard Approved, Title 46-Part 111.
Form Size Definition
The term “Form Size” refers to the physical overall size of a cord connector.
Form 1 is the smallest size.
Form 8 is the largest size.
Knockout Holes
Knockout Hole Recommended Knockout Hole Recommended Knockout Hole Recommended
NPT Min. to Max. PG Metric
Hub Size Inches (mm) Hub Size Inches (mm) Hub Size Inches (mm)
¼ .54"-.57" (13.7-14.5) PG7 492" (12.5) M12 .472" (12)
³⁄₈ .67"-.70" (17.0 -17. 8 ) PG9 599" (15.2) M16 .629" (16)
½ .86"-.91" (21.8-23.0) PG11 .733" (18.6) M20 .787" (20)
¾ 1.04"-1.09" ( 2 6 .4 - 2 7. 8 ) PG13.5 .804" (20.4) M25 .984" (25)
1 1.36"-1.41" (34.5-35.7) PG16 .888" (22.5) M32 1.25" (32)
1¼ 1.72"-1.77" (43.7-44.9) PG21 1.15" (28.3) M40 1.57" (40)
1½ 1.97"-2.02" (50.0 -51.2) PG29 1.47" (34.3)
2 2.45"-2.50" (62.3-63.5) PG36 1.85" ( 47. 0 )
2½ 2.95"-3.00" (75.0-76.2)
3 3.58"-3.63" ( 9 0. 9 - 92.1)
NPT, PG and Metric Thread Low Profile Connectors
Specifications
Material 6/6 Nylon.
Gland Buna N.
Temperature Range -22°F to 225°F (-30°C to 107°C).
Cord Connectors are Halogen and Silicon free.
Protection Class IP66 Suitability.
Flammability UL 94V-2.
Listings/Certifications UL Listing File E-41567, UL Recognition File E-41567.
CSA File LR27378C, VDE Marks Licence #136681.
Kellems® Wire Management Products
Technical Information
Cord Connectors
SECP29G
www.hubbell-wiring.comV-88 Wiring Device-Kellems
®
A
(Overall)
B Ref.
C
D
F
E
Straight Hubbell Connectors
Aluminum Inches (mm) Nylon Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
E A
Dia.
B
Ref.
C D
Throat
Dia.
E
A/C* A/F* A/C* A/F*
¼-18 1.88"
(22.4)
.90"
(22.9)
.46"
(11.7 )
.32"
(8 .1)
.99"
(25.1)
.88"
(22.4)
1.00"
(25.4)
1.10"
( 27. 9 )
.43"
(10.9)
.33"
(8.4)
.1.0 0"
(25.4)
.93"
(23.6)
³⁄₈-18 1.88"
(22.4)
.90"
(22.9)
.46"
(11.7 )
.44"
(11.2)
.99"
(25.1)
.88"
(22.4)
1.00"
(25.4)
1.10"
( 27. 9 )
.43"
(10.9)
.45"
(11.4)
.1.0 0"
(25.4)
.93"
(23.6)
½-14 1.88"
(22.4)
.90"
(22.9)
.46"
(11.7 )
.44"
(11.2)
1.00"
(25.4)
.88"
(22.4)
1.00"
(25.4)
1.10"
( 27. 9 )
.46"
(11.7 )
.45"
(11.4)
.1.0 0"
(25.4)
.93"
(23.6)
½-14 21.13"
(28.7)
1.10"
( 27. 9 )
.55"
(14.0)
.64"
(16.3)
1.11"
(28.2)
1.00"
(25.4)
1.32"
(33.5)
1.50"
(3 8.1)
.53"
(13.5)
.58"
(14.7)
1.25"
(31.7)
1.12"
(28.4)
½-14 31.38"
(3 5.1)
1.50"
(3 8.1)
.55"
(14.0)
.64"
(16.3)
1.40"
(35.6)
1.25"
(31.7)
——————
¾-14 21.13"
(28.7)
1.10"
( 27. 9 )
.55"
(14.0)
.64"
(16.3)
1.29"
(32.8)
1.13"
(28.7)
——————
¾-14 31.38"
(3 5.1)
1.50"
(3 8.1)
.55"
(14.0)
.82"
(20.8)
1.40"
(35.6)
1.25"
(31.7)
1.56"
(39.6)
1.60"
(40.6)
.55"
(14.0)
.77"
(19.6)
1.44"
(36.6)
1.31"
(33.3)
1-11½ 41.75"
(44.4)
1.60"
(40.6)
.71"
(18.0)
1.02"
(25.9)
1.81"
(46.0)
1.62"
(41.1)
1.88"
( 47. 8 )
1.75"
(44.4)
.70"
( 17. 8 )
1.01"
(25.7)
1.84"
(46.7)
1.63"
(41.4)
1-11½ 52.31"
(58.7)
1.70"
(43.2)
.66"
(16.8)
1.01"
(25.7)
2.28"
( 5 7. 9 )
2.00"
(50.8)
——————
1¼-11½ 52.31"
(58.7)
1.70"
(43.2)
.74"
(18.8)
1.26"
(32.0)
2.28"
( 5 7. 9 )
2.12"
(53.8)
——————
1½-11½ 52.31"
(58.7)
1.70"
(43.2)
.74"
(18.8)
1.38"
(3 5.1)
2.28"
( 5 7. 9 )
2.12"
(53.8)
— — ————
1½-11½ 63.00"
(76.2)
2.20"
(55.9)
.75"
(19.0)
1.50"
(3 8.1)
2.97"
(75.4)
2.75"
(69.8)
——————
2-11½ 63.00"
(76.2)
2.20"
(55.9)
.80"
(20.3)
1.92"
(48.8)
3.24"
(82.4)
3.00"
(76.2)
——————
2-11½ 73.85"
(97.8)
2.70"
(68.6)
.88"
(22.4)
1.94"
(49.3)
4.05"
(102.9)
3.75"
(95.2)
——————
2½-8 73.85"
(97.8)
2.70"
(68.6)
1.30"
(33.0)
2.32"
(58.9)
4.34"
(110.2)
4.02"
(102.1)
——————
2½-8 84.75"
(120.6)
2.70"
(68.6)
1.25"
(31.7)
2.38"
(60.5)
4.86"
(123.4)
4.50"
(114.3)
——————
3-8 73.85"
(97.8)
2.70"
(68.6)
1.30"
(33.0)
2.54"
(64.5)
4.34"
(110.2)
4.02"
(102.1)
——————
3-8 84.50"
(114.3)
2.70"
(68.6)
1.38"
(3 5.1)
3.00"
(76.2)
4.86"
(123.4)
4.50"
(114.3)
——————
Note: *A/C— Across Corners; A/F—Across Flats.
Kellems® Wire Management Products
Technical Information
Cord Connectors
Dimensions shown are approximate and
are subject to change without notice.
V-89www.hubbell-wiring.com Wiring Device-Kellems
®
A
(Overall)
B Ref.
C
D
F
E
Straight Hubbell Connectors
Zinc-Plated Steel Inches (mm) Stainless Steel Inches (mm)
F
NPT
Inches Form
A B
Ref.
C
D
Throat
Dia.
E A B
Ref.
C
D
Throat
Dia.
E
A/C* A/F* A/C* A/F* A/C* A/F* A/C* A/F*
¼- 18 1 — — — — — — — 1.01"
(25.7)
.88"
(22.4)
.90"
(22.9)
.46"
(11.7 )
.38"
(9.7)
.87"
(2 2.1)
.75"
(19.0)
³⁄₈-18 1.98"
(24.9)
.88"
(22.4)
.90"
(22.9)
.42"
(10.7)
.45"
(11.4)
.99"
(25.1)
.88"
(22.4)
1.01"
(25.7)
.88"
(22.4)
.90"
(22.9)
.46"
(11.7 )
.45"
(11.4)
.87"
(2 2.1)
.75"
(19.0)
½-14 1.98"
(24.9)
.88"
(22.4)
.90"
(22.9)
.55"
(14.0)
.45"
(11.4)
1.00"
(25.4)
.88"
(22.4)
———————
½-14 21.27"
(32.3)
1.13"
(28.7)
1.20"
(30.5)
.55"
(14.0)
.64"
(16.3)
1.10"
(28.2)
1.00"
(25.4)
1.30"
(33.0)
1.13"
(28.7)
1.10"
( 27. 9 )
.54"
(13.7)
.63"
(16.0)
1.16"
(29.5)
1.00"
(25.4)
½-14 31.55"
(39.4)
1.38"
(3 5.1)
1.50"
(3 8.1)
.55"
(14.0)
.64"
(16.3)
1.40"
(35.6)
1.25"
(31.7)
———————
¾-14 21.27"
(32.3)
1.13"
(28.7)
1.20"
(30.5)
.55"
(14.0)
.64"
(16.3)
1.29"
(32.8)
1.13"
(28.7)
———————
¾-14 31.55"
(39.4)
1.38"
(3 5.1)
1.40"
(35.6)
.55"
(14.0)
.82"
(20.8)
1.40"
(35.6)
1.25"
(31.7)
1.59"
(40.4)
1.38"
(3 5.1)
1.30"
(33.0)
.56"
(14.2)
.81"
(20.6)
1.44"
(36.6)
1.25"
(31.7)
1-11½ 31.55"
(39.4)
1.38"
(3 5.1)
1.40"
(35.6)
.70"
( 17. 8 )
.89"
(22.6)
1.54"
(3 9.1)
1.38"
(3 5.1)
———————
1-11½ 41.92"
(48.8)
1.69"
(42.9)
1.60"
(40.6)
.70"
( 17. 8 )
1.02"
(25.9)
1.95"
(49.5)
1.69"
(42.9)
2.02"
(51.3)
1.75"
(44.4)
1.40"
(35.6)
.70"
( 17. 8 )
1.03"
(26.2)
1.88"
( 47. 8 )
1.63"
(41.4)
1-11½ 52.40"
(61.0)
—1.70"
(43.2)
.70"
( 17. 8 )
1.02"
(25.9)
2.46"
(62.5)
2.15"
(54.6)
———————
1¼-11½ 52.40"
(61.0)
—1.70"
(43.2)
.73"
(18.5)
1.27"
(32.3)
2.48"
(63.0)
2.19"
(55.6)
———————
1½-11½ 52.40"
(61.0)
—1.70"
(43.2)
.74"
(18.8)
1.39"
(35.3)
2.48"
(63.0)
2.19"
(55.6)
———————
1½-11½ 63.06"
( 7 7.7 )
—2.20"
(55.9)
.75"
(19.0)
1.52"
(38.6)
3.04"
( 7 7. 2)
2.83"
(71.9)
———————
2-11½ 63.06"
( 7 7.7 )
—2.20"
(55.9)
.78"
(19.8)
1.92"
(48.8)
3.32"
(84.3)
3.07"
(78.0)
———————
2-11½ 73.95"
(100.3)
—2.70"
(68.6)
.78"
(19.8)
1.99"
(50.5)
4.18"
(106.2)
3.89"
(98.8)
———————
Note: *A/C— Across Corners; A/F—Across Flats.
Kellems® Wire Management Products
Technical Information
Cord Connectors
Dimensions shown are approximate and
are subject to change without notice.
www.hubbell-wiring.comV-90 Wiring Device-Kellems
®
Dimensions shown are approximate and
are subject to change without notice.
B Ref.
A
Ref.
D
C
E
F
G
B Ref.
A
D
C
E
F
G
45° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
EG
Dia.
A
Dia.
B
Ref.
C
D
Throat
Dia.
E G
Across
Corners
Across
Flats
Across
Corners
Across
Flats
Across
Corners
Across
Flats
½-14 22.00"
(50.8)
1.90"
(48.3)
.55"
(14.0)
.56"
(14.2)
1.27"
(32.3)
1.10"
( 27. 9 )
1.13"
(28.6)
1.97"
(50.0)
1.90"
(48.3)
.55"
(14.0)
.57"
(14.4)
1.24"
(31.5)
1.06"
(26.9)
1.27"
(32.3)
1.13"
(28.6)
¾-14 32.30"
(58.4)
2.50"
(65.3)
.56"
(14.2)
.75"
(19.0)
1.48"
( 3 7.6 )
1.28"
(32.5)
1.38"
(34.9)
————————
1-11½ 42.60"
(66.0)
2.80"
(71.1)
.70"
( 17. 8 )
1.00"
(25.4)
1.69"
(42.9)
1.50"
(3 8.1)
1.75"
(44.4)
————————
1½-11½ 53.90"
(9 9.1)
3.90"
(9.91)
.74"
(18.8)
1.25"
(31.7)
2.45"
(62.2)
2.13"
(54.0)
2.31"
(58.7)
————————
1½-11½ 53.90"
(9 9.1)
3.90"
(9 9.1)
.74"
(18.8)
1.50"
(3 8.1)
2.45"
(62.2)
2.13"
(54.0)
2.31"
(58.7)
————————
90° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
EG
Dia.
A
Dia.
B
Ref.
C
D
Throat
Dia.
E G
Across
Corners
Across
Flats
Across
Corners
Across
Flats
Across
Corners
Across
Flats
³⁄₈-18 11.27"
(32.3)
2.00"
(50.8)
.46"
(11.7 )
.44"
(11.2)
1.15"
(29.2)
1.10"
( 27. 9 )
.88"
(22.2)
————————
½-14 21.56"
(39.6)
2.30"
(58.4)
.50"
(12.7)
.55"
(13.9)
1.30"
(33.0)
1.13"
(28.7)
1.13"
(28.6)
1.65"
(41.9)
2.38"
(60.5)
.55"
(14.0)
.55"
(13.8)
1.29"
(32.8)
1.13"
(28.7)
1.27"
(32.3)
1.13"
(28.6)
¾-14 31.79"
(45.5)
2.80"
(71.1)
.56"
(14.2)
.77"
(19.4)
1.49"
(37.8)
1.31"
(33.3)
1.38"
(34.9)
1.88"
( 47. 8 )
2.90"
(73.7)
.56"
(14.2)
.77"
(19.4)
1.52"
(38.6)
1.33"
(33.8)
1.55"
(39.2)
1.38"
(34.9)
1-11½ 42.08"
(52.8)
3.20"
(81.3)
.70"
( 17. 8 )
1.00"
(25.4)
1.70"
(43.2)
1.50"
(3 8.1)
1.75"
(44.4)
2.16"
(54.9)
3.20"
(81.3)
.70"
( 17. 8 )
1.00"
(25.4)
1.72"
(43.7)
1.50"
(3 8.1)
1.92"
(48.8)
1.69"
(42.8)
1¼-11½ 53 .18"
(80.8)
4.30"
(109.2)
.73"
(18.5)
1.26"
(32.0)
2.47"
(62.7)
2.15"
(54.6)
2.31"
(58.7)
————————
1½-11½ 53.18"
(80.8)
4.30"
(109.2)
.75"
(19.2)
1.50"
(3 8.1)
2.47"
(62.7)
2.15"
(54.6)
2.31"
(58.7)
————————
2-11½ 63.51"
(89.2)
5.50"
(139.7)
.80"
(20.3)
1.92"
(48.8)
2.98"
(75.7)
2.78"
(70.6)
3.00"
(76.2)
————————
90° Hubbell Connectors
Nylon Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
EG
Dia.
Across
Corners
Across
Flats
³⁄₈-18 1———————
½-14 21.41"
(35.8)
2.50"
(63.5)
.55"
(14.0)
.58"
(14.6)
1.23"
(31.2)
1.12"
(28.2)
1.32"
(33.4)
¾-14 31.65"
(41.9)
2.81"
(71.4)
.56"
(14.2)
.77"
(19.4)
1.42"
(3 6.1)
1.29"
(32.8)
1.56"
(39.6)
1-11½ 41.99"
(50.5)
3.30"
(83.8)
.70"
( 17. 8 )
1.01"
(25.7)
1.82"
(46.2)
1.60"
(40.6)
1.88"
( 47. 6 )
Kellems® Wire Management Products
Technical Information
Cord Connectors
V-91www.hubbell-wiring.com Wiring Device-Kellems
®
A
(Overall)
B Ref.
C
D
F
E
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
A
D
C
F
B
E
SEALING NUT
Recommended
knockout size
Dimensions shown are approximate and
are subject to change without notice.
Low Profile Non-Metallic NPT, PG and Metric Thread Connectors
Nylon Inches (mm)
Hub Size A B C D E F
³⁄₈ NPT 0.670" (17.0) 1.41" (35.8) 0.48" (12.4) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
½ NPT 0.875" (22.2) 1.70" (43.2) 0.61" (15.5) 0.21" (5.3) 0.88" (24.8) 0.66" (16.8)
¾ NPT 1.0 6 8 " (27.1) 2.00" (50.8) 0.62" (15.7) 0.25" (6.3) 1.30" (33.0) 0.85" (21.6)
1 NPT 1.375" (35.0) 2.41" (61.2) 0.76" (19.3) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
PG7 0.492" (12.5) 1.16" (29.5) 0.32" (8.1) 0.21" (5.3) 0.63" (16.0) 0.48" (12.4)
PG9 0.599" (15.2) 1.25" (31.8) 0.32" (8.1) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
PG11 0.733" (18.6) 1.48" (37.6) 0.38" (9.7) 0.21" (5.3) 0.94" (23.9) 0.70" (17.8)
PG13.5 0.804" (20.4) 1.53" (38.9) 0.41" (10.4) 0.21" (5.3) 0.98" (24.9) 0.66" (16.8)
PG16 0.888" (22.5) 1.68" (42.7) 0.44" (11. 2) 0.25" (6.4) 1.06" (27.0) 0.76" (19.3)
PG21 1.15" (28.3) 1.89" (48.0) 0.52" (13.2) 0.25" (6.4) 1.30" (33.0) .085" (21.6)
PG29 1.47" (37.30) 2.23" (56.6) 0.58" (14.7) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
PG36 1.85" (47. 0) 2.39" (60.7) 0.47" (11.9) 0. 31" ( 7. 9 ) 2.05" (52.7) 1.19 " (30.2)
M12 0.473" (12.0) 1.16" (29.5) 0.32" (8.1) 0.21" (5.3) 0.63" (16.0) 0.49" (12.4)
M16 0.630" (16.0) 1.25" (31.8) 0.32" (8.1) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
M20 0.787" (20.0) 1.53" (38.9) 0.41" (10.4) 0.21" (5.3) 0.98" (24.9) 0.66" (16.8)
M25 0.985" (25.0) 1.89" (48.0) 0.52" (13.2) 0.25" (6.3) 1.30" (33.0) 0.85" (21.6)
M32 1.260" (32.0) 2.23" (56.6) 0.58" (14.7) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
M40 1.575" (40.0) 2.39" (60.7) 0.48" (12.2) 0.30" (7.6) 2.05" (52.1) 1.19" (30.2)
Female Hubbell Connectors
Aluminum Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
E
Across
Corners
Across
Flats
³⁄₈-18 1.88"
(22.4)
1.40"
(35.6)
.56"
(14.2)
.44"
(11.2)
.94"
(23.9)
.81"
(20.6)
½-14 21.13"
(28.7)
1.80"
(45.7)
.56"
(14.2)
.63"
(16.0)
1.15"
(29.2)
1.00"
(25.4)
¾-14 21.13"
(28.7)
2.10"
(53.3)
.75"
(19.0)
.63"
(16.0)
1.44"
(36.6)
1.25"
(31.7)
1-11½ 41.75"
(44.5)
2.30"
(58.4)
.88"
(22.4)
1.10"
( 27. 9 )
1.88"
( 47. 8 )
1.63"
(41.4)
1¼-11½ 52.31"
(58.7)
2.80"
(71.1)
.95"
(24.1)
1.43"
(36.3)
2.64"
( 6 7.1)
2.29"
(58.2)
1½-11½ 52.31"
(58.7)
2.80"
(71.1)
.95"
(24.1)
1.43"
(36.3)
2.64"
( 6 7.1)
2.29"
(58.2)
Underground Feeder Connectors
Aluminum Inches (mm) Zinc-Plated Steel Inches (mm) Nylon Inches (mm)
F
NPT
Inches Form
A
Dia.
B
Ref.
C
D
Throat
Dia.
E A B
Ref.
C
D
Throat
Dia.
E A
Dia.
B
Ref.
C
D
Throat
Dia.
E
A/C* A/F* A/C* A/F* A/C* A/F* A/C* A/F*
½-14 21.13"
(28.7)
1.10"
( 27. 9 )
.55"
(14.0)
.64"
(16.3)
1.10"
( 27. 9 )
1.00"
(25.4)
1.27"
(32.3)
1.13"
(28.7)
1.20"
(30.5)
.55"
(14.0)
.64"
(16.3)
1.11"
(28.2)
1.00"
(25.4)
1.32"
(33.5)
1.50"
(3 8.1)
.55"
(14.0)
.58"
(14.7)
1.25"
(31.7)
1.13"
(28.7)
¾-14 21.13"
(28.7)
1.10"
( 27. 9 )
.55"
(14.0)
.64"
(16.3)
1.29"
(32.8)
1.13"
(25.4)
1.27"
(32.3)
1.13"
(28.7)
1.20"
(30.5)
.55"
(14.0)
.64"
(16.3)
1.29"
(32.8)
1.13"
(28.7)
——————
¾-14 31.13"
(28.7)
1.50"
(3 8.1)
.55"
(14.0)
.82"
(20.8)
1.40"
(35.6)
1.25"
(31.7)
1.55"
(39.4)
1.38"
(3 5.1)
1.40"
(35.6)
.56"
(14.2)
.82"
(20.8)
1.40"
(35.6)
1.25"
(31.7)
1.56"
(39.6)
1.60"
(40.6)
.56"
(14.2)
.77"
(19.6)
1.44"
(36.6)
1.31"
(33.3)
Note: *A/C - Across Corners; A/F - Across Flats.
Kellems® Wire Management Products
Technical Information
Cord Connectors
www.hubbell-wiring.comV-92 Wiring Device-Kellems
®
2 Conductors
Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approx. Dia.
Inches (mm)
.25"
(6.2)
.31"
( 7. 8 )
.33"
(8.4)
.37"
(9.3)
.38"
(9.7)
.40"
(10.2)
.54"
(13.7)
.62"
(15.6)
.68"
(17.1)
.81"
(20.6)
Color Black Black White White Blue Blue Brown Brown Yellow Orchid
NPT Form Catalog Number*
¼ 1 HC1004 HC1004 HC1005 HC1005 HC1006 HC1006 — — — —
³⁄₈ 1HC1010 HC1010 HC1011 HC1011 HC1012 HC1012 — — — —
½ 1 HC1016 HC1016 HC1017 HC1017 HC1018 HC1018 — — — —
½ 2 HC1022 HC1022 HC1022 HC1022 HC1023 HC1023 HC1024 HC1024 — —
½ 3 — — — — HC1025 HC1025 HC1026 HC1026 HC1027 HC1028
¾ 2 HC1032 HC1032 HC1032 HC1032 HC1033 HC1033 HC1034 HC1034 — —
¾ 3 — — — — HC1035 HC1035 HC1036 HC1036 HC1037 HC1038
1 4 — — — — HC1039 HC1039 HC1040 HC1040 HC1041 HC1042
1 5 — — — — — — — — — HC1045
1¼ 5 — — — — — — — — — HC1050
1½ 5 — — — — — — — — — HC1055
1½ 6 — — — — — — — — — —
2 6 — — — — — — — — — —
2 7 — — — — — — — — — —
2½ 7 — — — — — — — — — —
3 7 — — — — — — — — — —
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
3 Conductors
Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approx. Dia.
Inches (mm)
.26"
(6.5)
.33"
(8.3)
.35"
(8.9)
.39"
(9.8)
.39"
(9.9)
.42"
(10.7)
.57"
(14.4)
.65"
(16.4)
.71"
(18.0)
.85"
(21.5)
Color Black White White Blue Blue Blue Brown Yellow Yellow Orchid
NPT Form Catalog Number*
¼ 1 HC1004 HC1005 HC1005 HC1006 HC1006 HC1006 — — — —
³⁄₈ 1HC1010 HC1011 HC1011 HC1012 HC1012 HC1012 — — — —
½ 1 HC1016 HC1017 HC1017 HC1018 HC1018 HC1018 — — — —
½ 2 HC1022 HC1022 HC1022 HC1023 HC1023 HC1023 HC1024 — — —
½ 3 — — — HC1025 HC1025 HC1025 HC1026 HC1027 HC1027 HC1028
¾ 2 HC1032 HC1032 HC1032 HC1033 HC1033 HC1033 HC1034 — — —
¾ 3 — — — HC1035 HC1035 HC1035 HC1036 HC1037 HC1037 HC1038
1 4 — — — HC1039 HC1039 HC1039 HC1040 HC1041 HC1041 HC1042
1 5 — — — — — — — — — HC1045
1¼ 5 — — — — — — — — — HC1050
1½ 5 — — — — — — — — — HC1055
1½ 6 — — — — — — — — — —
2 6 — — — — — — — — — —
2 7 — — — — — — — — — —
2½ 7 — — — — — — — — — —
3 7 — — — — — — — — — —
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
Kellems® Wire Management Products
Technical Information
Cord Connectors
V-93www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
Technical Information
Cord Connectors
2 Conductors
Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approx. Diameter
Inches (mm)
.94"
(23.8)
1.08"
(27.4)
1.17"
(29.7)
1.27"
(33.3)
1.44"
(36.6)
1.52"
(38.6)
1.65"
(41.9)
1.77"
(45.0)
1.92"
(48.8)
2.16"
(51.9)
Color Gray‡ Pink‡ ‡‡‡‡‡‡‡‡
NPT Form Catalog Number*
¼ 1 — — — — — — — — — —
³⁄₈ 1 — — — — — — — — — —
½ 1 — — — — — — — — — —
½ 2 — — — — — — — — — —
½ 3 — — — — — — — — — —
¾ 2 — — — — — — — — — —
¾ 3 — — — — — — — — — —
1 4 HC1043 HC1044 — — — — — — — —
1 5 HC1046 HC1047 HC1048 HC1049 — — — — — —
1¼ 5HC1051 HC1052 HC1053 HC1054 — — — — — —
1½ 5HC1056 HC1057 HC1058 HC1059 — — — — — —
1½ 6 — — — HC1060 HC1061 HC1062 HC1063 HC1064 — —
2 6 — — — HC1065 HC1066 HC1067 HC1068 HC1069 — —
2 7 — — — — — — — HC1070 HC1071 HC1073
2½ 7 — — — — — — — HC1076 HC1077 HC1079
3 7 — — — — — — — HC1086 HC1087 HC1089
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
3 Conductors
CordType SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approx. Diameter
Inches (mm)
1.00"
(25.4)
1.17"
(29.7)
1.24"
(31.5)
1.34"
(34.0)
1.51"
(38.4)
1.65"
(41.9)
1.75"
(44.5)
1.80"
(48.0)
2.07"
(52.6)
2.39"
(60.7)
Color Gray‡ ‡‡‡‡‡‡‡‡‡
NPT Form Catalog Number*
¼ 1 — — — — — — — — — —
³⁄₈ 1 — — — — — — — — — —
½ 1 — — — — — — — — — —
½ 2 — — — — — — — — — —
½ 3 — — — — — — — — — —
¾ 2 — — — — — — — — — —
¾ 3 — — — — — — — — — —
1 4 HC1044 — — — — — — — — —
1 5 HC1047 HC1048 HC1048 HC1049 — — — — — —
1¼ 5HC1052 HC1053 HC1053 HC1054 — — — — — —
1½ 5HC1057 HC1058 HC1058 HC1059 — — — — — —
1½ 6 — — — HC1060 HC1062 HC1063 HC1064 — — —
2 6 — — — HC1065 HC1067 HC1068 HC1069 — — —
2 7 — — — — — — HC1070 HC1071 HC1073 HC1075
2½ 7 — — — — — — HC1076 HC1077 HC1079 HC1081
3 7 — — — — — — HC1086 HC1087 HC1089 HC1091
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
www.hubbell-wiring.comV-94 Wiring Device-Kellems
®
4 Conductors
Cord Type SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #16 #14 #18 #16 #14 #12 #10 #8
Approx. Diameter
Inches (mm)
.36"
(9.0)
.39"
(9.8)
.43"
(10.8)
.42"
(10.7)
.45"
(11.4)
.61"
(15.5)
.70"
( 17. 8 )
.77"
(19.4)
.97"
(24.6)
Color White Blue Blue Blue Blue Brown Yellow Orchid Gray‡
NPT Form Catalog Number*
¼ 1 HC1005 HC1006 HC1006 HC1006 — — — — —
³⁄₈ 1HC1011 HC1012 HC1012 HC1012 — — — — —
½ 1 HC1017 HC1018 HC1018 HC1018 — — — — —
½ 2 HC1022 HC1023 HC1023 HC1023 HC1023 HC1024 — — —
½ 3 — HC1025 HC1025 HC1025 HC1025 HC1026 HC1027 HC1028 —
¾ 2 — HC1033 HC1033 HC1033 HC1033 HC1034 — — —
¾ 3 — HC1035 HC1035 HC1035 HC1035 HC1036 HC1037 HC1038 —
1 4 — HC1039 HC1039 HC1039 HC1039 HC1040 HC1041 HC1042 HC1043
1 5 — — — — — — — — HC1046
1¼ 5 — — — — — — — — HC1051
1½ 5 — — — — — — — — HC1056
1½ 6 — — — — — — — — —
2 6 — — — — — — — — —
2 7 — — — — — — — — —
2½ 7 — — — — — — — — —
3 7 — — — — — — — — —
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
5 Conductors
Cord Type S, SO, ST, STO
Cord Size #18 #16 #14 #12 #10 #8 #6
Approx. Dia.
Inches (mm)
.50" .54" .70" .76" .83" 1.06" 1.18 "
(12.7) (13.7) (17.7 ) (19.3) (21.1) (26.9) (30.0)
Color Blue Brown Yellow Orchid‡ Orchid‡ Pink‡ ‡
NPT Form Catalog Number*
½ 2 HC1023 HC1024 — — — — —
½ 3 HC1025 HC1026 HC1027 HC1028 HC1028 — —
¾ 2 HC1033 HC1034 — — — — —
¾ 3 HC1035 HC1036 HC1037 HC1038 HC1038 — —
1 4 HC1039 HC1040 HC1041 HC1042 HC1042 HC1044 —
1 5 — — — HC1045 HC1045 HC1047 HC1048
1¼ 5 — — — HC1050 HC1050 HC1052 HC1053
1½ 5 — — — HC1055 HC1055 HC1057 HC1058
Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95.
‡F5 and larger will not be color coded.
Kellems® Wire Management Products
Technical Information
Cord Connectors
V-95www.hubbell-wiring.com Wiring Device-Kellems
®
Note:
1. Add the proper prefix to the HC number to identify
the type of connector desired:
SHC = Straight Hubbell Connector
NHC = 90° Hubbell Connector
FHC = Female Hubbell Connector
VHC = 45° Hubbell Connector
2. Add the proper suffix to identify material desired:
Aluminum = No suffix
Zinc-Plated Steel = ZP
Corrosion Resistant Nylon = CR
Stainless Steel = SS
3. This chart is a general guide to assist in the selection of
Hubbell Cord Connectors for various cord sizes. The Hubbell
Cord Connector catalog numbers selected, have been
inserted into spaces which in our judgment represent the
best cord connector which will fit the listed cord size.
The diameters of the cords are approximate and may vary
depending on the manufacturer. It is suggested that the
appropriate cord manufacturer’s dimension chart be
consulted for exact dimensions.
4. Cable jacket may have to be stripped to allow conductors
to pass through connector body.
Kellems® Wire Management Products
Technical Information
Cord Connectors
4 Conductors
Cord Type SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0
Approx. Diameter
Inches (mm)
.94"
(23.8)
1.08"
(27.4)
1.17"
(29.7)
1.27"
(33.3)
1.44"
(36.6)
1.52"
(38.6)
1.65"
(41.9)
1.77"
(45.0)
1.92"
(48.8)
Color Pink‡ ‡‡‡‡‡‡‡‡
NPT Form Catalog Number*
¼ 1 — — — — — — — — —
³⁄₈ 1 — — — — — — — — —
½ 1 — — — — — — — — —
½ 2 — — — — — — — — —
½ 3 — — — — — — — — —
¾ 2 — — — — — — — — —
¾ 3 — — — — — — — — —
1 4 HC1044 — — — — — — — —
1 5 HC1047 HC1049 HC1049 — — — — — —
1¼ 5HC1052 HC1054 HC1054 — — — — — —
1½ 5HC1057 HC1059 HC1059 — — — — — —
1½ 6 — HC1060 HC1060 HC1061 HC1063 HC1064 — — —
2 6 — HC1064 HC1065 HC1066 HC1068 HC1069 — — —
2 7 — — — — — HC1070 HC1071 HC1073 HC1074
2½ 7 — — — — — HC1076 HC1077 HC1079 HC1080
3 7 — — — — — HC1086 HC1087 HC1089 HC1090
Note: *Must add prefix, see Note 1; suffix, see Note 2, below.
‡F5 and larger will not be color coded.
www.hubbell-wiring.comV-96 Wiring Device-Kellems
®
A
Thread Size
(N.P.S.)
C
Minimum
Thk.
B
Maximum
Diameter
A
C
B
A C
B
NPT Thread Locknuts
Zinc-Plated Steel
NPT
Hub
Size
A
Inside Diameter
B
Outside Dia.
C
Thickness Steel
Catalog NumberInches Inches (mm) Inches (mm)
½½"-14 1.14" (29.0) .09" (2.3) 00322001LPK50
¾¾"-14 1.43" (36.3) .11" (2.8) 00322002LPK50
11"-11½ 1.77" (45.0) .13" (3.3) 00322003LPK50
1¼ 1¼"-11½ 2.28" ( 5 7. 9 ) .13" (3.3) 00322004LPK50
1½ 1½"-11½ 2.60" (66.0) .13" (3.3) 00322005LPK50
Metal Clad Sealing O-Rings – Sizes ½ - 4
Zinc-Plated Steel with Neoprene Ring
NPT
Hub
Size
A
Inside Diameter
B
Outside Dia.
C
Thickness
Catalog NumberInches (mm) Inches (mm) Inches (mm)
½.80" (20.3) 1.08" (27.4) .16" (3.2) 20509001
¾1.00" (25.4) 1.34" (34.0) .16" (3.2) 20509002
11.25" (31.6) 1.63" (41.4) .16 " (3.2) 20509003
1¼ 1.61" (40.9) 2.00" (50.8) .16" (3.2) 20509004
1½ 1.84" (46.7) 2.36" (59.9) .16" (3.2) 20509005
22.31" (58.7) 2.83" (71.9) .16" (3.2) 20509006
Chrome Plated Steel with Neoprene Ring
2½ 2.91" (73.9) 3.44" (87.4) .24" ( 6.1) 20509007
3 3.52" (89.4) 4.08" (103.6) .24" (6.1) 20509008
Nylon PG Thread Locknuts
PG Thread
Size
A
Inches (mm)
B
Inches (mm)
C
Inches (mm) Catalog Number
PG7 .75" (19.1) .80" (20.3) .22" (5.6) LNP7BPK100
PG9 .86" (21.8) .91" (23.2) .22" (5.6) LNP9BPK100
PG11 .94" (23.9) 1.03" (26.2) .22" (5.6) LNP11BPK100
PG13.5 1.0 6" (26.9) 1.14" (29.0) .24" (6.1) LNP13BPK10 0
PG16 1.18" (30.0) 1.30" (33.0) .25" (6.1) LNP16BPK100
PG21 1.41" (35.8) 1.54" (3 9.1) .25" ( 6.1) LNP21BPK100
PG29 1.81" (46.0) 2.00" (50.8) .25" (6.1) LNP29BPK25
PG36 2.24" (56.9) 2.50" (63.5) .25" (6.1) LNP36BPK25
Nylon Metric Thread Locknuts
PG Thread
Size
A
Inches (mm)
B
Inches (mm)
C
Inches (mm) Catalog Number
M12 .75" (19.1) .82" (20.8) .22" (5.6) LNM12BPK100
M16 .87" (22.09) .98" (25.0) .22" (5.6) LNM16BPK100
M20 1.06" ( 27. 0 ) 1.18 " (30.0) .25" (6.4) LNM20BPK100
M25 1.38" (35.1) 1.54" (39.1) .28" ( 7.1) LNM25BPK100
M32 1.61" (40.9) 1.80" (45.7) .28" ( 7.1) LNM32BPK100
M40 1.97" (50.0) 2.18" (55.4) .28" ( 7.1) LNM40BPK100
Kellems® Wire Management Products
Technical Information
Locknuts and Sealing O-Rings
Dimensions shown are approximate and
are subject to change without notice.
V-97www.hubbell-wiring.com Wiring Device-Kellems
®
Hubbell Juniors®
Material Operating Temperature Range
Nylon (connectors and GOTCHA® rings) -40°F to +225°F (-40°C to +107°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
Due to the limiting factors of nylon and neoprene, any complete liquidtight Hubbell Junior will continuously perform in the range
of -30°F to +225°F (-34°C to +107°C).
Snap-In continuously performs -40°F to +225°F (-40°C to +107°C).
Flammability
Hubbell Juniors have a UL 94V-2 rating.
Certifications
Product Agency
Liquidtight and Liquidtight with Spiral UL Listed.
CSA Certified.
Snap-In UL Recognized.
CSA Certified.
Knockout Holes
Knockout Hole
Recommended
NPT Min. to Max.
Hub Size inches (mm)
¼ .54"-.57" (13.7-14.5 )
³⁄₈ .67"-.70" (17. 0 -17. 8 )
½ .86"-.91" (21.8 -23.1)
Kellems® Wire Management Products
Technical Information
Hubbell Juniors® Miniature Nylon Cord Connectors
Dimensions shown are approximate and
are subject to change without notice.
B
E
F
C
D
A
B
F
G
DE
AC
G
D
F
C
B
AChassis
Thickness
Max
E
Snap-In
Diameter
Range
Inches
(mm)
For Chassis
Thickness
(Max.)
Inches
(mm)
Required
Hole Size
A
Inches
(mm)
B
Inches
(mm)
Dimensional
Specifications
E
Inches
(mm)
F
Inches
(mm)
G
Inches
(mm)
C
Inches
(mm)
D
Inches
(mm)
.22"-.27"
(5.6-6.9)
.10"
(2.5)
.50"
(12.7)
.45"
(11.4)
.28"
(7.1)
.28"
(7.1)
.54"
(13.7)
.12"
(3.0)
1.84"
(44.2)
.28"-.32"
(7.1-8.1)
.10"
(2.5)
.50"
(12.7)
.47"
(11.9)
.28"
(7.1)
.33"
(8.4)
.59"
(15.0)
.12"
(3.0)
1.84"
(44.2)
.30"-.36"
(7.6-9.1)
.13"
(3.3)
.63"
(16.0)
.55"
(14.0)
.36"
(9.1)
.37"
(9.4)
.65"
(16.5)
.14"
(3.6)
2.18"
(55.4)
.32"-.43"
(8.1-10.9)
.13"
(3.3)
.75"
(19.0)
.66"
(16.8)
.45"
(11.4)
.44"
(11.2)
.75"
(19.1)
.14"
(3.6)
2.60"
(66.0)
Liquidtight
F
NPT
Inches
A
Dia.
Inches
(mm)
B
Ref.
Inches
(mm)
C
Inches
(mm)
D
Throat
Dia.
Inches
(mm)
E
Across
Corners
Inches
(mm)
Across
Flats
Inches
(mm)
¼-18 .65"
(16.5)
1.30"
(33.0)
.40"
(10.2)
.29"
(7.4)
.65"
(16.5)
.60"
(15.2)
³⁄₈-18 .81"
(20.6)
1.44"
(36.6)
.41"
(10.4)
.36"
(9.1)
.81"
(20.6)
.75"
(19.1)
½-14 1.00"
(25.4)
1.56"
(39.6)
.46"
(11.7)
.45"
(11.4)
.99"
(25.1)
.92"
(23.4)
Liquidtight with Spiral
G
NPT
Inches
A
Dia.
Inches
(mm)
B
Ref.
Inches
(mm)
C
Inches
(mm)
D
Throat
Dia.
Inches
(mm)
E
Inches
(mm)
F
Across
Corners
Inches
(mm)
Across
Flats
Inches
(mm)
¼-18 .65"
(16.5)
2.55"
(64.8)
.40"
(10.2)
.29"
(7.4)
.27"
(6.9)
.65"
(16.5)
.60"
(15.2)
³⁄₈-18 .81"
(20.6)
3.10"
(78.7)
.41"
(10.4)
.36"
(9.1)
.35"
(8.9)
.81"
(20.6)
.75"
(19.1)
½-14 1.00"
(25.4)
3.72"
(94.5)
.46"
(11.7)
.45"
(11.4)
.45"
(11.4)
.99"
(25.1)
.92"
(23.4)
www.hubbell-wiring.comV-98 Wiring Device-Kellems
®
Kellems® Wire Management Products
PolyTuff® I and PolyTuff® II Non-Metallic Liquidtight Conduit
Features and Benefits
Rigid PVC core bonded to
flexible PVC jacket
All non-metallic construction
ends metal fatigue and
separation problems
Cuts cleanly with a knife
or PVC cutter so there are
no jagged metal edges
UL Listed and
CSA Certified
PolyTuff® I Conduit, Gray or Black
PVC core with corrugated walls
bonded to PVC jacket
Handles twists, turns, bends,
switchbacks and straightaways
with ease
All non-metallic construction
ends fatigue and separation
problems
Can be cut with a knife
or PVC cutters
UL Recognized and
CSA Certified
PolyTuff® II Tubing
Trade Size (metric designator) Feet (m) Catalog Number
¼ (10) 100 (30.5) B2025
³⁄₈ (12) 100 (30.5) B2038
½ (16) 100 (30.5) B2050
¾ (21) 100 (30.5) B2075
1 (27) 100 (30.5) B2100
1¼ (35) 100 (30.5) B2125
1½ (41) 50 (15.2) B2150
2 (53) 50 (15.2) B2200
Note: See page V-100 for approved fittings.
See pages V-102 and V-103 for technical information and dimensional drawings.
IP66
SUITABILITY
PolyTuff® I Conduit
Trade Size (metric designator) Feet (m)
Gray
Catalog Number
Black
Catalog Number
³⁄₈ (12) 100 (30.5) G1038 G1038M1
½ (16) 100 (30.5) G1050 G1050M1
¾ (21) 100 (30.5) G1075 G1075M1
1 (27) 100 (30.5) G110 0 G1100M1
1¼ (35) 100 (30.5) G1125 G1125M1
1½ (41) 50 (15.2) G1150 G1150M1
2 (53) 50 (15.2) G1200 G1200M1
Note: See pages V-66 and V-67, V-100 and V-101 for approved fittings.
See pages V-102 and V-103 for technical information and dimensional drawings.
IP66
SUITABILITY
PolyTuff® II Tubing, Black
G1100
G1100M1
B2100
V-99www.hubbell-wiring.com Wiring Device-Kellems
®
Kellems® Wire Management Products
PolyTuff® Non-Metallic and Metallic Liquidtight Conduit Fittings
Features and Benefits
Non-integral ferrule provides
conduit seal and superior
pullout protection
Nylon compression nut has
a tapered dome to tighten
ferrule onto conduit
Neoprene O-ring provides
liquidtight seal at hub or enclosure
Nylon locknut fastens connector
securely to enclosure and provides
superior corrosion resistance
Nylon two-piece swivel body enables
fitting to twist from 0° to 90°
Hexagonal, screw-machined steel thru 1",
and malleable iron on larger sizes.
Nut compresses gland-ring onto conduit
Non-integral, reusable steel,
ferrule is easily installed, to
seal conduit
Tapered, machined threads fasten securely
and provide additional liquidtight sealing
Split, nylon, gland-ring compresses
conduit onto ferrule
Threaded one-piece
steel body
Locknut has hardened steel
tangs to grip securely
Nylon gasket provides
liquidtight seal at hub
Optional insulated and
non-insulated throat
www.hubbell-wiring.comV-100 Wiring Device-Kellems
®
PS05GYKIT
P0759NGY
P125NGY
P075NGYA
PS0509NGY
SwivelLok® Multi-Position
Straight with Male Non-Metallic Liquidtight Fittings
Trade Size
(metric designator)
Black
Catalog Number
Gray
Catalog Number
¼ (10)
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
F2025
P038NBKA
P050NBKA
P075NBKA
P100NBKA
—
P038NGYA
P050NGYA
P075NGYA
P10 0NGYA
1¼ (35)
1½ (41)
2 (53)
P125NBK
P150NBK
P200NBK
P125NGY
P150NGY
P200NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See pages V-104 and V-105 for technical information and dimensional drawings.
³⁄₈" Liquidtight conduit fitting have ½ NPT male threads.
SwivelLok® Multi-Position with Male Non-Metallic Liquidtight Fittings
Trade Size
(metric designator)
Black
Catalog Number
Gray
Catalog Number
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
PS0389NBK
PS0509NBK
PS0759NBK
PS1009NBK
PS0389NGY
PS0509NGY
PS0759NGY
PS1009NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See pages V-104 and V-105 for technical information and dimensional drawings.
³⁄₈" Liquidtight conduit fitting have ½ NPT male threads.
Fixed 90°Fittings for Non-Metallic Conduit
Trade Size
(metric designator)
Black
Catalog Number
Gray
Catalog Number
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
1¼ (35)
P0389NBK
P0509NBK
P0759NBK
P1009NBK
P1259NBK
P0389NGY
P0509NGY
P0759NGY
P1009NGY
P1259NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See pages V-104 and V-105 for technical information and dimensional drawings.
³⁄₈⁄⁄" Liquidtight conduit fitting have ½ NPT male threads.
SwivelLok® Flexible Conduit Kit
Trade Size
(metric designator) Fitting and Conduit Catalog Number
½ (16)
¾ (21)
2 PS0509NGY, 6' G1050
2 PS0759NGY, 6' G1075
PS05GYKIT
PS07GYKIT
Note: See pages V-104 and V-105 for technical information and dimensional drawings.
Kellems® Wire Management Products
PolyTuff® Non-Metallic Liquidtight Fittings
UL Listed to
Type 4, 4X, 12 and 13
V-101www.hubbell-wiring.com Wiring Device-Kellems
®
H050
Straight with Male
Hubbell Conduit Fitting
H0504
45° Angle with Male
Hubbell Conduit Fitting
H0509
90° Angle with Male
Hubbell Conduit Fitting
Straight Conduit Fitting
Trade Size
(metric designator) Insulated Non-Insulated
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
H0381
H0501
H0751
H1001
H038
H050
H075
H100
1¼ (35)
1½ (41)
2 (53)
2½ (63)
H1251
H1501
H2001
H2501
H125
H150
H200
H250
3 (78)
3½ (91)
4 (103)
H3001
H3501
H4001
H300
H350
H400
Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page V-106 for technical information.
45° Conduit Fitting
Trade Size
(metric designator) Insulated Non-Insulated
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
H03841
H05041
H07541
H10041
H0384
H0504
H0754
H1004
1¼ (35)
1½ (41)
2 (53)
H12541
H15041
H20041
H1254
H1504
H2004
Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page V-106 for technical information.
90° Conduit Fitting
Trade Size
(metric designator) Insulated Non-Insulated
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
H03891
H05091
H07591
H10091
H0389
H0509
H0759
H1009
1¼ (35)
1½ (41)
2 (53)
2½ (63)
3 (78)
4 (103)
H12591
H15091
H20091
H25091
H30091
H40091
H1259
H1509
H2009
H2509
H3009
H4009
Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page V-106 for technical information.
Kellems® Wire Management Products
Metallic Liquidtight Conduit Fittings
www.hubbell-wiring.comV-102 Wiring Device-Kellems
®
PolyTuff® I Conduit
Operating Temperature Range
Wet environment 0°F to +140°F (-18°C to +60°C).
Oil environment 0°F to +158°F (-18°C to +70°C).
Dry environment 0°F to +176°F (-18°C to +80°C).
Certifications
UL Listed UL Standard 1660. Sunlight resistant approved for outdoor use, direct burial.
CSA Certified Meets requirements of NEC.
Voltage Rating
Maximum 600V.
Material
Conduit Co-extruded rigid and flexible PVC.
PolyTuff® II Tubing
Operating Temperature Range
Operating environment 0°F to +140°F (-18°C to +60°C).
Certifications
UL Recognized
CSA Certified
Voltage Rating
Maximum Same as wire insulation rating.
Material
Tubing Co-extruded rigid and flexible PVC.
PolyTuff® I Conduit
Trade Size
(metric Conduit ID/OD Bend Radius
designator) Inches (mm) Inches (mm)
³⁄₈ (12) .49"/.70" (12 . 6 /17. 8 ) 2.00" (50.8)
½ (16) .63"/.83" (16 .1/21.1) 3.00" (76.2)
¾ (21) .83"/1.04" (21.1/26.4) 4.00" (101.6)
1 (27) 1.05"/1.30" (26.0/33.1) 5.00" ( 2 17. 0 )
1¼ (35) 1.40"/1.65" (35.4/41.8) 6.30" (158.8)
1½ (41) 1.59"/1.88" (40.3/47.8) 7. 5 0 " (190.5)
2 (53) 2.03"/2.36" (51.6/59.9) 10.00" (254.0)
PolyTuff® II Tubing
Trade Size
(metric Conduit ID/OD Bend Radius
designator) Inches (mm) Inches (mm)
¼ (10) . 36"/.57" (9.3/14.5) 1.50" (3 8.1)
³⁄₈ (12) .49"/.70" (12 . 6 /17. 8 ) 2.00" (50.8)
½ (16) .63"/.83" (16 .1/21.1) 2.00" (50.8)
¾ (21) .83"/1.04" (21.1/26.4) 3.00" (76.2)
1 (27) 1.05"/1.30" (26.0/33.1) 3.00" (76.2)
1¼ (35) 1.40"/1.65" (35.4/41.8) 5.00" (12 7.0 )
1½ (41) 1.59"/1.88" (40.3/47.8) 5.00" ( 127. 0 )
2 (53) 2.03"/2.36" (51.6/59.9) 5.00" (12 7.0 )
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Conduit and Tubing
V-103www.hubbell-wiring.com Wiring Device-Kellems
®
Acetate Solvents D D
Acetic Acid B C
Acetic Acid (Glacial) C D
Acetone D D
Acrylontrile A B
Alcohols (Aliphatic) C C
Aluminum Chloride A A
Aluminum Sulfate (Alums) A A
Ammonia (Anhydrous Liquids) D D
Ammonia (Aqueous) A A
Ammoniated Latex A C
Ammonium Chloride A A
Ammonium Hydroxide A A
Amyl Acetate D D
Aniline Oils D D
Aromatic Hydrocarbons D D
Asphalt D D
ASTM Fuel A C C
ASTM Fuel B D D
ASTM #1 Oil B C
ASTM #3 Oil C D
Barium Chloride A A
Barium Sulfide A A
Barium Hydroxide A A
Benzene (Benzol) D D
Benzine (Petroleum Ether) C C
Black Liquor A A
Bordeaux Mixture A A
Boric Acid A A
Butyl Acetate D D
Butyl Alcohol B C
Calcium Hydroxide A A
Calcium Hypochlorite A A
Carbolic Acid (Phenol) B C
Carbon Dioxide A A
Carbon Disulfide D D
Carbon Tetrachloride D D
Carbonic Acid A A
Casein A C
Caustic Soda A B
Chlorine Gas (wet) D D
Chlorine Gas (dry) D D
Chlorine (water solution) C D
Chlorobenzene D D
Chlorinated Hydrocarbons D D
Chromic Acid B C
Citric Acid A A
Coal Tar D D
Coconut Oil C D
Corn Oil A B
Cottonseed Oil C D
Creosote D D
Cresol C D
Crysylic Acid D D
Cyclohexane B C
DDT Weed Killer A C
Dibutyl Phthalate D D
Diesel Oils C D
Diethylene Glycol B C
Diethyl Ether A C
Di-isodecyl Phthalate D D
Dioctyl Phthalate D D
Dow General Weed Killer (Phenol) D D
Dow General Weed Killer (H2O) B C
Ethyl Alcohol C C
Ethylene Dichloride D D
Ethylene Glycol B C
Ferric Chloride A A
Ferric Sulfate A A
Ferrous Chloride A A
Ferrous Sulfate A A
Formaldehyde D D
Fuel Oil B C
Furfural C C
Gallic Acid A A
Gasoline (Hi Test) C D
Glycerine A A
Grease A C
Green Sulfate Liquor A A
Heptachlor in Petroleum Solvents A C
Heptane C D
Hexane C D
Hydrobromic Acid A A
Hydrochloric Acid 10% A A
Hydrochloric Acid 40% C C
Hydrofluoric Acid 70% D D
Hydrofluorosilicic Acid A A
Hydrofluorosilicic Acid 10% A A
Hydrogen Peroxide A B
Iso-Octane C C
Isopropyl Acetate D D
Isopropyl Acid B C
Jet Fuels (JP-3, and 5) C D
Kerosene C C
Ketones D D
Linseed Oil A A
Lubricating Oils A A
Magnesium Chloride A A
Magnesium Hydroxide A A
Magnesium Sulfate A A
Malathion 50 in Aromatics D D
Malic Acid A A
Methyl Acetate D D
Methyl Alcohol C C
Methyl Bromide D D
Methyl Ethyl Ketone D D
Methylene Chloride D D
Mineral Oil
Monochlorobenezene A A
Muriatic Acid (see Hydrochloric Acid)
Naphtha C D
Naphthalene D D
Nitric Acid 10% A B
Nitric Acid 35% A C
Nitric Acid 70% D D
Oleic Acid A C
Oleum D D
Oxalic Acid A A
Pentachlorophenol in Oil B C
Pentane C D
Perchloroethylene B C
Petroleum Ether C C
Phenol A A
Phosphoric Acid 10% A A
Pitch 50% A B
Potassium Hydroxide C D
Sodium Cyanide A A
Stoddard Solvent D D
Styrene D D
Sulfur Dioxide (liquid) D D
Sulfuric Acid 50% A B
Sulfuric Acid 98% D D
Sulfurous Acid B C
Tall Oil D D
Tannic Acid A A
Toluene D D
Trichlorethylene D D
Triethanol Amine C D
Tricresyl Phosphate (Skydrol) D D
Turpentine C D
Vinegar A B
Vinyl Chloride D D
Water A A
White Liquor A A
Xylene D D
Zinc Chloride A A
Zinc Sulfate A A
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Conduit and Tubing
PolyTuff® I and II Conduit/Tubing; PVC Chemical Resistance
Temp. Temp. Temp.
Chemical Conc.* 70°F 150°F Chemical Conc.* 70°F 150°F Chemical Conc.* 70°F 150°F
21°C 66°C 21°C 66°C 21°C 66°C
Note: *Conc. = Concentration.
(All ratings apply to concentrated or saturated solutions unless otherwise specified.)
Chemical resistance ratings are based upon information supplied by the raw material manufacturers.
Use as a general guide only – samples should be tested by user under actual conditions.
A-Excellent service
No harmful effect to reduce service life. Suitable for
continuous service.
B-Good service life.
Moderate to minor effect. Good for intermittent service.
Generally suitable for continuous service.
C-Fair or limited service.
Depends on operating conditions. Generally suitable for intermittent
service. Not recommended for continuous service.
D-Unsatisfactory service.
Not recommended.
Rating Code
www.hubbell-wiring.comV-104 Wiring Device-Kellems
®
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Fittings
PolyTuff® Fittings
Operating Temperature*
Nylon (Body, Nut, Gripping Ring and Locknut) –40°F to +225°F (–40°C to +107°C).
Neoprene (Sealing Ring) –30°F to +240°F (–34°C to +116°C).
Flammability
Fire Gas Toxicity Product Testing Nylon PolyTuff Fittings have a UL 94V-2 rating.
Certifications
UL Listed UL50 Type 4X, 12 and 13.
CSA Certified PolyTuff I Fittings, PolyTuff II Fittings.
Liquidtight Fittings
Operating Temperature**
Steel/Malleable Iron (Nut, Body, Ferrule) –60°F to +1000°F (–51°C to +538°C).
Nylon (Gland Ring) –40°F to +225°F (–40°C to +107°C).
Hazardous Locations - NEC Reference
Class I, Div. 2 - 501-10(A)(3)B
Class II, Div. 1 - 502-10(A)(2)
Class II, Div. 2 - 502-10(A)(3)
Class III, Div. 1 - 503-10(A)(2)
Class III, Div. 2 - 503-10(B)
Certifications
UL Listed to UL 514B
CSA Certified
Note: *Due to the limiting factors of nylon and neoprene, PolyTuff Fittings will continuously perform in the range –30°F to +225°F (–34°C to +107°C).
**Due to the limiting factors of nylon, metallic liquidtight flexible conduit fittings will continuously perform in the range of –40°F to +225°F (–40°C to +107°C).
V-105www.hubbell-wiring.com Wiring Device-Kellems
®
45° Position
D
A
G
90° Position
F
EB
C
Straight Position
A
Dia.
B
D
C
E
Sizes: 3/8", ½", ¾", 1"
A
C
E
B
D
Sizes: ¼", 1¼", 1½", 2"
A
Dia.
C
E
B
D
Straight with Male Non-Metallic Liquidtight Fittings
Trade
Size
(md**) A B C
D
Throat
Dia.
E
Across
Corners
Across
Flats
¼
(10)
.93"
(23.6)
1.45"
(36.8)
.39"
(9.9)
.32"
(8 .1)
.86" (Dia.)
(21.8)
³⁄₈
(12)
1.14"
(29.0)
1.63"
(41.4)
.57"
(14.5)
.42"
(10.7)
1.41"
(35.8)
1.30"
(33.0)
½
(16)
1.30"
(33.0)
2.14"
(54.4)
.57"
(14.5)
.55"
(14.0)
1.41"
(35.8)
1.30"
(33.0)
¾
(21)
1.53"
(38.9)
2.22"
(56.4)
.58"
(14.7)
.74"
(18.8)
1.85"
( 47.0 )
1.53"
(38.9)
1
(27)
1.80"
(45.7)
2.32"
(58.9)
.72"
(18.3)
.96"
(24.4)
1.94"
(49.3)
1.80"
(45.7)
1¼
(35)
2.20"
(55.9)
2.15"
(54.6)
.74"
(18.8)
1.30"
(33.0)
2.38"
(60.5)
2.18"
(55.4)
1½
(41)
2.49"
(63.2)
2.35"
(59.7)
.76"
(19.3)
1.46"
(37.1)
2.63"
(66.8)
2.43"
(61.7)
2
(53)
3.05"
( 7 7.4 )
2.51"
(63.6)
.79"
(20.1)
1.90"
(48.3)
3.13"
(79.5)
2.93"
(74.4)
90° with Male Non-Metallic Liquidtight Fittings
Trade
Size
(md**) A B C
D
Throat
Dia.
E
Across
Corners
Across
Flats
¼
(10)
.93"
(23.6)
1.88"
( 47. 8 )
.39"
(9.9)
.32"
(8 .1)
.86"(Dia.)
(21.8)
1¼
(35)
2.21"
(5 6.1)
3.57"
(90.7)
.74"
(18.9)
1.30"
(33.0)
2.38"
(60.5)
2.18"
(55.4)
SwivelLok® Multi-Position Liquidtight Fittings
Trade
Size
(md**) A B C D E F
G
Across
Corners
Across
Flats
³⁄₈
(12)
1.30"
(33.0)
3.27"
(8 3.1)
.57"
(14.5)
.55"
(14.0)
1.43"
(36.3)
2.00"
(50.8)
1.41"
(35.8)
1.30"
(33.0)
½
(16)
1.30"
(33.0)
3.27"
(8 3.1)
.57"
(14.5)
.55"
(14.0)
1.43"
(36.3)
2.00"
(50.8)
1.41"
(35.8)
1.30"
(33.0)
¾
(21)
1.53"
(38.9)
3.66"
(93.0)
.58"
(15.7)
.74"
(18.8)
1.59"
(40.4)
2.23"
(56.6)
1.65"
(41.9)
1.53"
(38.9)
1
(27)
1.80"
(45.7)
4.00"
(101.6)
.72"
(18.3)
.96"
(24.4)
1.84"
(46.7)
2.30"
(58.4)
1.94"
(49.3)
1.80"
(45.7)
Note: *A/C = Across Corners, A/F = Across Flats.
**md = metric designator.
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Fittings
www.hubbell-wiring.comV-106 Wiring Device-Kellems
®
A
E
Throa
t
Dia.
B
D
C
F
D
Throa
t
Dia.
E
C
A
B
Ref.
B
E
Throat
Dia.
D
C
A
F
Straight with Male Metallic Metal Fitting
Trade Size
(md**)
A
Ref. B
CD
Throat Dia.
E
A/C* A/F* A/C* A/F*
³⁄₈
(12)
1.43"
(36.3)
.59"
(15.0)
1.20"
(30.0)
1.06"
(26.9)
.61"
(15.5)
1.07"
( 27. 2 )
.93"
(23.6)
½
(16)
1.43"
(36.3)
.59"
(15.0)
1.34"
(34.0)
1.19"
(30.2)
.61"
(15.5)
1.22"
(31.0)
1.06"
(26.9)
¾
(21)
1.56"
(39.6)
.59"
(15.0)
1.55"
(39.0)
1.37"
(34.8)
.84"
(21.3)
1.43"
(36.3)
1.25"
(31.8)
1
(27)
1.68"
(42.7)
.66"
(16.8)
1.95"
(50.0)
1.69"
(42.9)
1.06"
(26.9)
1.73"
(43.9)
1.56"
(39.6)
1¼
(35)
2.03"
(51.6)
.63"
(16.8)
2.39"
(61.0)
2.06"
(52.3)
1.37"
(34.8)
2.36"
(59.9)
2.08"
(52.8)
1½
(41)
2.21"
(5 6.1)
.63"
(16.8)
2.72"
(69.0)
2.38"
(60.5)
1.53"
(38.9)
2.79"
(70.9)
2.48"
(63.0)
2
(53)
2.28"
( 5 7. 9 )
.69"
(17. 5 )
3.08"
(78.0)
2.87"
(72.9)
2.06"
(52.3)
3.32"
(84.3)
2.90"
(73.7)
2½
(63)
3.56"
(90.4)
1.06"
(26.9)
3.92"
(100.0)
3.62"
(91.9)
2.42"
(61.5)
3.85"
(97.8)
3.60"
(91.4)
3
(78)
3.81"
(96.8)
1.06"
(26.9)
4.70"
(119.0 )
4.31"
(109.5)
3.01"
(76.5)
4.65"
(118.1)
4.33"
(110.0 )
3½
(91)
3.81"
(96.8)
1.06"
(26.9)
5.29"
(134.0)
4.81"
(122.2)
3.49"
(88.6)
5.18"
(131.6)
4.82"
(122.4)
4
(103)
3.81"
(96.8)
1.06"
(26.9)
5.75"
(146.0)
5.31"
(134.9)
3.96"
(100.6)
5.75"
(14 6.1)
5.39"
(136.9)
45° with Male Metallic Metal Fitting
Trade Size
(md**)
A B C D E
Throat Dia.
F
A/C* A/F* A/C* A/F*
³⁄₈
(12)
1.19"
(30.2)
1.28"
(32.5)
.59"
(15.0)
1.20"
(30.5)
1.06"
(26.9)
.60"
(15.2)
1.16"
(29.5)
1.02"
(25.9)
½
(16)
1.19"
(30.2)
1.28"
(32.5)
.59"
(15.0)
1.34"
(34.0)
1.19"
(30.2)
.61"
(15.2)
1.21"
(30.7)
1.06"
(26.9)
¾
(21)
1.19"
(30.2)
1.43"
(36.3)
.59"
(15.0)
1.55"
(39.4)
1.45"
(36.8)
.84"
(21.3)
1.50"
(3 8.1)
1.32"
(33.5)
1
(27)
1.38"
(3 5.1)
1.53"
(38.9)
.66"
(16.8)
1.95"
(49.5)
1.69"
(42.9)
1.05"
(26.7)
1.82"
(46.2)
1.59"
(40.4)
1¼
(35)
1.42"
(3 6.1)
1.69"
(42.9)
.63"
(16.0)
2.39"
(60.7)
2.06"
(52.3)
1.37"
(34.8)
2.32"
(58.9)
2.03"
(5.16)
1½
(41)
1.66"
(42.2)
2.00"
(50.8)
.66"
(16.8)
2.72"
(6 9.1)
2.38"
(60.5)
1.60"
(40.6)
2.62"
(66.5)
2.29"
(58.2)
2
(53)
1.69"
(42.9)
2.25"
( 57. 2 )
.66"
(16.8)
3.08"
(78.2)
2.88"
(73.2)
2.05"
(52.1)
3.21"
(81.5)
2.80"
(71.1)
90° with Male Metallic Metal Fitting
Trade Size
(md**)
A B C D
Ref.
E
Throat Dia.
F
A/C* A/F* A/C* A/F*
³⁄₈
(12)
1.31"
(33.3)
.59"
(15.0)
1.20"
(30.5)
1.06"
(26.9)
1.44"
(36.6)
.60"
(15.2)
1.13"
(29.0)
.99"
(25.1)
½
(16)
1.31"
(33.3)
.59"
(15.0)
1.34"
(34.0)
1.12"
(28.4)
1.44"
(36.6)
.61"
(15.5)
1.12"
(28.0)
1.00"
(25.4)
¾
(21)
1.44"
(36.6)
.59"
(15.0)
1.55"
(39.4)
1.45"
(36.8)
1.63"
(41.4)
.83"
(21.1)
1.48"
(38.0)
1.29"
(32.8)
1
(27)
1.78"
(45.2)
.59"
(15.0)
1.95"
(49.5)
1.60"
(40.6)
2.19"
(55.6)
1.05"
(26.7)
1.80"
(46.0)
1.57"
(39.9)
1¼
(35)
1.97"
(50.0)
.63"
(16.0)
2.39"
(60.7)
2.06"
(52.3)
2.50"
(63.5)
1.36"
(34.5)
2.32"
(59.0)
2.02"
(51.3)
1½
(41)
2.19"
(55.6)
.63"
(16.0)
2.72"
(6 9.1)
2.38"
(60.5)
2.69"
(68.3)
1.61"
(40.9)
2.58"
(66.0)
2.25"
( 57. 2 )
2"
(53)
2.53"
(64.3)
.66"
(16.8)
3.08"
(78.2)
2.87"
(72.9)
3.25"
(82.6)
2.05"
(52.1)
3.14"
(80.0)
2.75"
(69.9)
2½
(63)
3.44"
(87. 4)
1.00"
(25.4)
3.92"
(99.6)
3.63"
(92.2)
4.25"
(108.0)
2.42"
(61.5)
3.78"
(96.0)
3.50"
(88.9)
3
(78)
3.75"
(95.3)
1.00"
(25.4)
4.70"
(119.4)
4.31"
(109.5)
4.87"
(123.7)
3.01"
(76.5)
4.64"
(118.0)
4.30"
(109.2)
4
(103)
4.25"
(108.0)
1.00"
(25.4)
5.75"
(14 6.1)
5.31"
(134.9)
5.63"
(143.0)
3.96"
(100.6)
5.76"
(146.0)
5.38"
(136.7)
Note: *A/C = Across Corners, A/F = Across Flats.
**md = metric designator.
Kellems® Wire Management Products
Technical Information
Metallic Liquidtight Fittings
