LM199,LM299,LM399 LM199/LM299/LM399 Precision Reference Literature Number: SNVS751C LM199/LM299/LM399 Precision Reference General Description The LM199 series are precision, temperature-stabilized monolithic zeners offering temperature coefficients a factor of ten better than high quality reference zeners. Constructed on a single monolithic chip is a temperature stabilizer circuit and an active reference zener. The active circuitry reduces the dynamic impedance of the zener to about 0.5 and allows the zener to operate over 0.5 mA to 10 mA current range with essentially no change in voltage or temperature coefficient. Further, a new subsurface zener structure gives low noise and excellent long term stability compared to ordinary monolithic zeners. The package is supplied with a thermal shield to minimize heater power and improve temperature regulation. The LM199 series references are exceptionally easy to use and free of the problems that are often experienced with ordinary zeners. There is virtually no hysteresis in reference voltage with temperature cycling. Also, the LM199 is free of voltage shifts due to stress on the leads. Finally, since the unit is temperature stabilized, warm up time is fast. The LM199 can be used in almost any application in place of ordinary zeners with improved performance. Some ideal applications are analog to digital converters, calibration standards, precision voltage or current sources or precision power supplies. Further in many cases the LM199 can replace references in existing equipment with a minimum of wiring changes. The LM199 series devices are packaged in a standard hermetic TO-46 package inside a thermal shield. The LM199 is rated for operation from -55C to +125C while the LM299 is rated for operation from -25C to +85C and the LM399 is rated from 0C to +70C. Features n n n n n n n n n Guaranteed 0.0001%/C temperature coefficient Low dynamic impedance -- 0.5 Initial tolerance on breakdown voltage -- 2% Sharp breakdown at 400 A Wide operating current -- 500 A to 10 mA Wide supply range for temperature stabilizer Guaranteed low noise Low power for stabilization -- 300 mW at 25C Proven reliability, low-stress packaging in TO-46 integrated-circuit hermetic package, for low hysteresis after thermal cycling. 33 million hours MTBF at TA = +25C (TJ = +86C) Connection Diagram Metal Can Package (TO-46) 00571714 Top View NS Package Number H04D Ordering Information Order Number Initial Tolerance Ambient Temperature LM199AH 2% 2% 2% 5% 5% LM199AH/883 LM299H LM399AH LM399H (c) 2005 National Semiconductor Corporation Package Marking Transport Method -50C to +125C LM199AH Box of 500 H04A -50C to +125C LM199AH/Q Tray of 20 H04A -25C to +85C LM299H Box of 500 H04A 0C to +70C LM399AH Box of 500 H04A 0C to +70C LM399H Box of 500 H04A DS005717 NSC Package www.national.com LM199/LM299/LM399 Precision Reference April 2005 LM199/LM299/LM399 Absolute Maximum Ratings (Note 1) Reference to Substrate Voltage V(RS) (Note 2) Specifications for Military/Aerospace products are not contained in this datasheet. Refer to the following Reliability Electrical Test Specifications documents: MNLM199A-X and SMD#5962-88561 . Operating Temperature Range -0.1V Temperature Stabilizer Voltage LM199 -55C to +125C LM299 -25C to +85C LM399 LM199/LM299/LM399 40V Reverse Breakdown Current 40V -0C to +70C Storage Temperature Range 20 mA -55C to +150C Soldering Information Forward Current TO-46 package (10 sec.) LM199/LM299/LM399 +300C 1 mA Electrical Characteristics (Notes 3, 6) Parameter Conditions Reverse Breakdown Voltage 0.5 mA IR 10 mA Reverse Breakdown Voltage 0.5 mA IR 10 mA LM299H LM399H Units Min Typ Max Min Typ Max 6.8 6.95 7.1 6.6 6.95 7.3 V 6 9 6 12 mV 0.5 1.5 Change with Current Reverse Dynamic Impedance IR = 1 mA Reverse Btreakdown Temperature Coefficient -25CTA85C LM299 0CTA+70C LM399 RMS Noise Long Term Stability 0.5 1 0.00003 0.0001 10 Hz f 10 kHz 7 20 Stabilized, 22CTA28C, 20 %/C 0.00003 0.0002 7 50 20 %/C V ppm 1000 Hours, IR=1 mA 0.1% Temperature Stabilizer TA=25C, Still Air, VS=30V 8.5 14 Supply Current TA =- 55C 22 28 Temperature Stabilizer 9 40 8.5 9 15 mA 40 V Supply Voltage Warm-Up Time to 0.05% VS = 30V, TA = 25C Initial Turn-on Current 9VS40, TA=+25C, (Note 4) 3 3 140 200 sec. 140 200 mA Electrical Characteristics (Notes 3, 6) Parameter Conditions Reverse Breakdown Voltage 0.5 mA IR 10 mA Reverse Breakdown Voltage 0.5 mA IR 10 mA LM199AH LM399AH Units Min Typ Max Min Typ Max 6.8 6.95 7.1 6.6 6.95 7.3 V 6 9 6 12 mV 0.5 1.5 Change with Current Reverse Dynamic Impedance IR = 1 mA Reverse Breakdown Temperature Coefficient -55CTA+85C +85CTA+125C 0CTA+70C LM199A 0.5 1 0.00002 0.00005 0.0005 0.0010 %/C LM399A RMS Noise 10 Hz f 10 kHz 7 Long Term Stability Stabilized, 22CTA28C, 20 %/C 20 0.00003 0.0001 %/C 7 50 V 20 ppm 1000 Hours, IR=1 mA 0.1% Temperature Stabilizer TA=25C, Still Air, VS=30V Supply Current TA =- 55C 8.5 22 Temperature Stabilizer 9 14 8.5 15 mA 40 V 28 40 9 Supply Voltage Warm-Up Time to 0.05% VS = 30V, TA = 25C Initial Turn-on Current 9VS40, TA=+25C, (Note 4) www.national.com 3 140 2 3 200 140 sec. 200 mA (Continued) Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Note 2: The substrate is electrically connected to the negative terminal of the temperature stabilizer. The voltage that can be applied to either terminal of the reference is 40V more positive or 0.1V more negative than the substrate. Note 3: These specifications apply for 30V applied to the temperature stabilizer and -55CTA+125C for the LM199; -25CTA+85C for the LM299 and 0CTA+70C for the LM399. Note 4: This initial current can be reduced by adding an appropriate resistor and capacitor to the heater circuit. See the performance characteristic graphs to determine values. Note 5: Do not wash the LM199 with its polysulfone thermal shield in TCE. Note 6: A military data sheet is available for the LM199AH/833 and LM199AH-SMD (SMD#5962-88561) upon request. Functional Block Diagram LM199/LM299/LM399 00571715 3 www.national.com LM199/LM299/LM399 Electrical Characteristics (Notes 3, 6) LM199/LM299/LM399 Typical Performance Characteristics Reverse Characteristics Reverse Voltage Change 00571720 00571719 Dynamic Impedance Zener Noise Voltage 00571721 00571722 Stabilization Time Heater Current 00571724 00571723 www.national.com 4 (Continued) Initial Heater Current Heater Current (To Limit This Surge, See Next Graph) 00571725 00571726 Heater Surge Limit Resistor vs Minimum Supply Voltage at Various Minimum Temperatures Low Frequency Noise Voltage 00571703 00571727 *Heater must be bypassed with a 2 F or larger tantalum capacitor if resistors are used. Response Time 00571707 5 www.national.com LM199/LM299/LM399 Typical Performance Characteristics LM199/LM299/LM399 Typical Applications Negative Heater Supply with Positive Reference Single Supply Operation 00571730 00571728 Buffered Reference With Single Sypply Split Supply Operation 00571731 00571729 Positive Current Source 00571732 www.national.com 6 LM199/LM299/LM399 Typical Applications (Continued) Standard Cell Replacement 00571733 Negative Current Source 00571734 Portable Calibrator* Square Wave Voltage Reference 00571735 00571736 *Warm-up time 10 seconds; intermittent operation does not degrade long term stability. 7 www.national.com LM199/LM299/LM399 Typical Applications (Continued) 14V Reference Precision Clamp* 00571737 00571738 *Clamp will sink 5 mA when input goes more positive than reference 0V to 20V Power Reference 00571739 Bipolar Output Reference 00571740 www.national.com 8 LM199/LM299/LM399 Schematic Diagrams Temperature Stabilizer 00571701 Reference 00571713 9 www.national.com LM199/LM299/LM399 Precision Reference Physical Dimensions inches (millimeters) unless otherwise noted NS Package H04D National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated