SMM0102 Vishay Draloric Metal Film, Cylindrical Resistors FEATURES * Stable metal film on high quality ceramic * Low TC and tight tolerances * Excellent stability * Pure tin termination on nickel barrier, plated on press fit steel caps * Compatible with lead (Pb)-free and lead containing soldering processes * Lead (Pb)-free and RoHS compliant STANDARD ELECTRICAL SPECIFICATIONS MODEL LIMITING ELEMENT POWER RATING1) P70 VOLTAGE2) DC or AC rms V W TEMPERATURE COEFFICIENT ppm/K TOLERANCE % RESISTANCE RANGE E-SERIES SMM0102 0.20 100 15 0.1 100R - 100K 24 - 96 SMM0102 0.20 100 25 0.1 100R - 100K 24 - 96 SMM0102 0.20 100 50 1.0 10R - 2M21 24 - 96 Zero-Ohm-Resistor : OMM0102 Rmax = 10 m Imax = 2 A Note 1. Permissible dissipation depends on the maximum temperature atthe solder point, the component placement density and the substrate material. 2. Rated voltage: * Further values and tolerances on request * Marking: According to IEC 60062; see also data sheet "surface mount resistor marking" (document number: 20020) PxR . TECHNICAL SPECIFICATIONS PARAMETER UNIT SMM0102 Rated Dissipation at 70 C W 0.2 Limiting Element Voltage, DC or AC rms V 100 Insulation Voltage (1 min), DC or AC peak V 150 Thermal Resistance3) K/W 250 Insulation Resistance 1010 Category Temperature Range C - 55 to + 125 10-9/h <2 g 7.8 Failure Rate Weight/1000 pcs Note 3. Based on measurements on test board acc. to EN 140400. www.vishay.com 22 For Technical questions contact: ff3bresistors@vishay.com Document Number: 20003 Revision: 16-Feb-06 SMM0102 Vishay Draloric Metal Film, Cylindrical Resistors DIMENSIONS DIMENSIONS [in millimeters] MODEL SMM0102 Dmax d* L Amax Amin 1.1 D - 0.05 2.2 - 0.15 0.45 0.35 * d measured in the middle of the resistor SOLDER PAD DIMENSIONS [in millimeters] REFLOW SOLDERING WAVE SOLDERING MODEL SMM0102 a b l a b l 0.5 1.3 1.3 0.6 1.3 1.3 PART NUMBER AND PRODUCT DESCRIPTION1) PART NUMBER2): SMM01020D5620BB3 PART NUMBER2): OMM01020000000B3 S M M 0 1 0 2 0 D 5 6 2 0 B B 3 0 0 O M M 0 1 0 2 0 0 0 0 0 0 0 B 3 0 0 MODEL/SIZE SMM0102 OMM0102 SPECIAL CHARACTER 0 = neutral TC E = 15 ppm/K D = 25 ppm/K C = 50 ppm/K 0 = Jumper VALUE 3 digit value 1 digit multiplier 0000 = Jumper Multiplier 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 4 = *104 TOLERANCE B = 0.1 % F=1% 0 = Jumper PACKING3) B1 B3 B0 M8 SPECIAL up to 2 digits 00 = standard PRODUCT DESCRIPTION: SMM0102 25 562R 0.1% B3 PRODUCT DESCRIPTION: OMM0102 0R0 B3 SMM0102 25 562R 0.1 % B3 OMM0102 - 0R0 - B3 MODEL TC RESISTANCE VALUE TOLERANCE PACKING3) SMM0102 OMM0102 15 ppm/K 25 ppm/K 50 ppm/K 100 = 100 2M21 = 2.21M 0R0 = jumper 0.1 % 1% B1 B3 B0 M8 Note 1. Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER. 2. The PART NUMBER is shown to facilitate the introduction of a unified part numbering system. Currently, this PART NUMBER is applicable in the Americas only. 3. Please refer to table PACKING, see below. Document Number: 20003 Revision: 16-Feb-06 For Technical questions contact: ff3bresistors@vishay.com www.vishay.com 23 SMM0102 Vishay Draloric Metal Film, Cylindrical Resistors PACKING BLISTER TAPE ON REEL ACC IEC 60286-3 BULK CASE ACC. IEC 60286-6 MODEL DIAMETER PIECES/REEL CODE 180 mm/7" 1000 B1* 180 mm/7" 3000 B3 330 mm/13" 10000 B0 PIECES/BULK CASE CODE 8000 M8 SMM0102 OMM0102 * For further information about packing see also data sheet "surface mount resistor packing" (document number: 20014) Rated Power in % * For TC 25 ppm/K and Tolerance 0.25 % only 120 100 80 60 40 20 0 - 55 Derating www.vishay.com 24 - 25 0 25 155 75 100 125 70 Ambient Temperature in C 50 For Technical questions contact: ff3bresistors@vishay.com Document Number: 20003 Revision: 16-Feb-06 SMM0102 Metal Film, Cylindrical Resistors Vishay Draloric PERFORMANCE REQUIREMENTS1) TEST CONDITIONS OF TEST Endurance Test at 70 C 1000 hours at 70 C, 1.5 hours "ON", 0.5 hours "OFF" 0.25 % IEC 60115-1, 4.25.1 8000 hours at 70 C, 1.5 hours "ON", 0.5 hours "OFF" 0.5 % 1000 hours at 125 C without load 0.5 % Short time overload for 2 seconds at 6.25 x rated power 0.1 % Endurance at UCT IEC 60115-1, 4.25.3 Overload Test IEC 60115-1, 4.13 Thermal Shock Rapid change between upper and lower category temperature, IEC 60115-1, 4.19 and IEC 60068-2-14 5 cycles Damp Heat Steady State 0.1 % 56 days at 40 C and 93 % relative humidity 0.5 % 10 seconds at 260 C solder bath temperature 0.1 % IEC 60115-1, 4.24 and IEC 60068-2-78 Resistance to Soldering Heat IEC 60115-1, 4.18 and IEC 60068-2-58 Note 1. For a resistance range from 10 to 221 k. APPLICABLE SPECIFICATIONS * EN 140401-803 * EN 140400 * EN 60115-1 Document Number: 20003 Revision: 16-Feb-06 For Technical questions contact: ff3bresistors@vishay.com www.vishay.com 25 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1