(P-TCB-E004) OUTLINE (Type TCB) Type TCB is a tantalum solid electrolytic capacitor with face-down terminal which uses conductive polymer as cathode layer. Their equivalent series resistance (ESR) is extremely lowered with characteristics of the polymer having high electric conductivity. This ensures higher permissible ripple current and excellent noise absorption performance on high-frequency circuits. APPLICATION Mobile phones, smart phones, digital cameras, high-performance portable equipments, personal computers, digital TV sets, DC/DC converters, regulators and peripherals FEATURES 1. Low ESR and Low impedance Using a conductive polymer as cathode layer makes low ESR and impedance possible. Type TCB makes high permissible ripple current and is suitable for noise bypass application. 2. Stable ESR over temperature. ESR is extremely stable from low temperature through high temperature. 3. Ultra Compact and Large capacitance The face-down terminal structure makes it possible to design land almost in same size as terminals. As result, components can be downsized, and mounting area can be reduced to 1/2 to 1/3 compared to the conventional structures. 4. Flame Retardancy Type TCB offers very safe characteristics which makes ignition and smoking harder by taking advantages of characteristics of conductive polymer if the capacitor be short-circuited. 5. Perfect Lead Free and RoHS Compliant. RATING Item Failure Rate Level Category Temperature Range Rated Voltage Derated Voltage Capacitance Capacitance Tolerances Rating 1% / 1000 h -55 to +105C (to be used at derated voltage when temperature exceeds 85C) 2.546.310 VDC 2.03.25.08.0 VDC (105C) 4.7100 F 20% (M) MARKING [10S,12S case] J Capacitance (2) GS [09M case] 1 Rated voltage ( ) Rated voltage (1) Polarity (Anode notion) Polarity (Anode notion) 1 Note( ) Rated voltage is described by alphabet, as shown below. Rated voltage codes Code e G J A Rated Voltage VDC 2.5 4 6.3 10 (2)Capacitance is described by alphabet or alphabet attached upper-bar, as shown below. Capacitance codes Code A E J N S W F 1 1.5 2.2 3.3 4.7 6.8 F A 10 E 15 J 22 N 33 S 47 W 68 Note(1) Rated voltage is described by alphabet, as shown below. Rated voltage codes Code e g j A Rated Voltage VDC 2.5 4 6.3 10 (2)Capacitance is described by alphabet and numeral, as shown below. Capacitance codes Code A7 E7 J7 N7 S7 10 15 22 33 47 Capacitance F W7 68 Capacitance Code Capacitance [10A,12A case] Rated voltage(1) Capacitance(2) Polarity (Anode notion) 1 A8 100 E8 150 J8 220 ORDERING INFORMATION TCB 1002 226 M R 10A 0150 TYPE RATED VOLTAGE CAPACITANCE CAPACITANCE TOLERANCE STYLE OF REELED PACKAGE CASE CODE ESR Rated Marking voltage Capacitance Marking Tolerance Capacitance Marking Anode Notation Reel Size Code Feed hole: - 180 Reel R Height of Case Code component EIA Code max. (mm) 2.5 2501 4.7 475 09M 0.9 1608 4 4001 6.8 685 10S 1.0 2012 6.3 6301 10 106 12S 1.2 2012 10 1002 15 156 10A 1.0 3216L 22 226 12A 1.2 3216L 33 336 47 476 68 686 100 107 20 Note : For a capacitor with special requirements from customers, a 2-digit specific numbers will be added between the case code and the ESR for our product management. STANDARD RATING March,2012 R.V.(VDC) Cap.(F) 2.5 4 6.3 10 4.7 09M(200,500) 09M(200,500) 09M(200,500) 09M(200,500) 6.8 09M(200,500) 09M(200,500) 09M(200,500) 09M(200,500) 10 09M(200,500) 09M(200,500) 09M(200,500) 15 09M(200,500) 09M(200,500) 22 12S(150) 47 12S(150,200) 68 12A(150) 100 12A(70,150) 12A(150,200) LOW PROFILE RATING R.V.(VDC) Cap.(F) 2.5 4 6.3 10 4.7 10S(300) 10 10A(70) 22 10S(150) 47 10S(200) 100 10A(200) 10A(60,150) The parenthesized values show ESR. (maximum values in m at 100 kHz) DIMENSIONS [Standard Rating] 09M Height (max.) 0.9 12S 2012 12A 3216L Case Code P1 P2 P1 (mm) EIA Code 1608 [Low Profile Rating] EIA Case Code Code 10S 2012 10A 3216L L 0.1 W 0.1 T 0.1 P1 0.1 P2 0.1 C 0.1 1.6 0.85 0.8 0.5 0.65 0.7 1.2 2.0 1.25 1.1 0.5 1.05 0.9 1.2 3.2 1.6 1.1 0.8 1.65 1.2 L 0.1 W 0.1 T 0.1 P1 0.1 P2 0.1 C 0.1 2.0 1.25 0.9 0.5 1.05 0.9 3.2 1.6 0.9 0.8 1.65 1.2 (mm) Height (max.) 1.0 1.0 2 b RECOMMENDED PAD DIMENSIONS a C Case Code a b c 09M 0.50 or more 0.65 0.65 10S,12S 0.50 or more 0.8 1.05 10A,12A 0.80 or more 1.1 1.65 In order to expect the self alignment effect, it is recommended that the land width is almost the same size as terminal of capacitor, and space between lands(c) nearly equal to the space between terminals for appropriate soldering. Adjust the mask opening so that the mask thickness is equivalent to 100 m. CATALOG NUMBERS AND RATING Max. permissible Ripple Current (2) (mArms) 20 85 105 -55 20 105 ESR (m) 100 kHz TCB 2501 475 M _1 09M 0500 2.5 4.7 20 09M 1.18 11.8 11.8 0.10 0.10 0.15 500 316 TCB 2501 475 M _1 09M 0200 4.7 09M 1.18 11.8 11.8 0.10 0.10 0.15 200 500 TCB 2501 685 M _1 09M 0500 6.8 09M 1.70 17.0 17.0 0.10 0.10 0.15 500 316 TCB 2501 685 M _1 09M 0200 6.8 09M 1.70 17.0 17.0 0.10 0.10 0.15 200 500 TCB 2501 106 M _1 09M 0500 10 09M 2.50 25.0 25.0 0.10 0.10 0.15 500 316 TCB 2501 106 M _1 09M 0200 10 09M 2.50 25.0 25.0 0.10 0.10 0.15 200 500 TCB 2501 156 M _1 09M 0500 15 09M 3.75 37.5 37.5 0.10 0.10 0.15 500 316 TCB 2501 156 M _1 09M 0200 15 09M 3.75 37.5 37.5 0.10 0.10 0.15 200 500 TCB 4001 475 M _1 09M 0500 4 4.7 20 09M 1.88 18.8 18.8 0.10 0.10 0.15 500 316 TCB 4001 475 M _1 09M 0200 4.7 09M 1.88 18.8 18.8 0.10 0.10 0.15 200 500 TCB 4001 685 M _ 09M 0500 6.8 09M 2.72 27.2 27.2 0.10 0.10 0.15 500 316 TCB 4001 685 M _1 09M 0200 6.8 09M 2.72 27.2 27.2 0.10 0.10 0.15 200 500 TCB 4001 106 M _1 09M 0500 10 09M 4.00 40.0 40.0 0.10 0.10 0.15 500 316 TCB 4001 106 M _1 09M 0200 10 09M 4.00 40.0 40.0 0.10 0.10 0.15 200 500 TCB 4001 156 M _1 09M 0500 15 09M 6.00 60.0 60.0 0.10 0.10 0.15 500 316 TCB 4001 156 M _1 09M 0200 15 09M 6.00 60.0 60.0 0.10 0.10 0.15 200 500 TCB 6301 475 M _1 09M 0500 6.3 4.7 20 09M 2.96 29.6 29.6 0.10 0.10 0.15 500 316 TCB 6301 475 M _1 09M 0200 4.7 09M 2.96 29.6 29.6 0.10 0.10 0.15 200 500 TCB 6301 685 M _1 09M 0500 6.8 09M 4.28 42.8 42.8 0.10 0.10 0.15 500 316 TCB 6301 685 M _1 09M 0200 6.8 09M 4.28 42.8 42.8 0.10 0.10 0.15 200 500 TCB 6301 106 M _1 09M 0500 10 09M 6.30 63.0 63.0 0.10 0.10 0.15 500 316 TCB 6301 106 M _1 09M 0200 10 09M 6.30 63.0 63.0 0.10 0.10 0.15 200 500 TCB 6301 106 M _1 10A 0070 10 10A 6.30 63.0 63.0 0.06 0.06 0.09 70 1055 TCB 6301 226 M _1 10S 0150 22 10S 13.8 138 138 0.06 0.06 0.09 150 658 TCB 6301 476 M _1 10S 0200 47 10S 29.6 296 296 0.08 0.08 0.12 200 570 TCB 6301 476 M _1 12S 0200 47 12S 29.6 296 296 0.08 0.08 0.12 200 570 TCB 6301 476 M _1 12S 0150 47 12S 29.6 296 296 0.08 0.08 0.12 150 658 TCB 6301 686 M _1 12A 0150 68 12A 42.8 428 428 0.08 0.08 0.12 150 721 TCB 6301 107 M _1 10A 0200 100 10A 63.0 630 630 0.10 0.10 0.15 200 624 TCB 6301 107 M _1 12A 0070 100 12A 63.0 630 630 0.08 0.08 0.12 70 1055 Catalog number (1) 1 TCB 6301 107 M _1 12A 0150 Rated Voltage (VDC) March,2012 Capacitance Tolerances (%) (F) Case Code Max. Dissipation Factor Lct. (A) 100 12A 63.0 630 630 0.08 0.08 0.12 150 721 TCB 1002 475 M _ 09M 0500 10 4.7 20 09M 4.70 47.0 47.0 0.10 0.10 0.15 500 316 TCB 1002 475 M _1 09M 0200 4.7 09M 4.70 47.0 47.0 0.10 0.10 0.15 200 500 TCB 1002 475 M _1 10S 0300 4.7 10S 4.70 47.0 47.0 0.10 0.10 0.15 300 465 TCB 1002 685 M _1 09M 0500 6.8 09M 6.80 68.0 68.0 0.10 0.10 0.15 500 316 TCB 1002 685 M _1 09M 0200 6.8 09M 6.80 68.0 68.0 0.10 0.10 0.15 200 500 TCB 1002 226 M _1 10A 0150 22 10A 22.0 220 220 0.06 0.06 0.09 150 721 TCB 1002 226 M _1 10A 0060 22 10A 22.0 220 220 0.06 0.06 0.09 60 1140 TCB 1002 226 M _1 12S 0150 22 12S 22.0 220 220 0.06 0.06 0.09 150 658 TCB 1002 476 M _1 12A 0150 47 12A 47.0 470 470 0.08 0.08 0.12 150 721 TCB 1002 476 M _1 12A 0250 47 12A 47.0 470 470 0.08 0.08 0.12 250 558 1 1 1 Notes : _ :No code for single item. `R' for taping specification. 2Reference value. 3 PERFORMANCE No Item 1 Leakage Current (A) Shall not exceed 0.1 CV Max. or the values shown in CATALOG NUMBERS AND RATING. 2 Capacitance (F) Shall be within specified tolerances. 3 Dissipation Factor Shall not exceed the values shown in CATALOG NUMBERS AND RATING. 4 Equivalent Series Resistance Shall not exceed the values shown in CATALOG NUMBERS AND RATING. 5 Characteristics at High and Low Temperature Step 1 Step 2 Step 3 Step 4 Step 5 6 Step 6 Surge Performance Test Method Dissipation Factor JIS C 5101-1, 4.9 Applied voltage : Rated voltage Duration : 5 min Measuring temperature : 202 JIS C 5101-1, 4.7 Measuring frequency : 120 Hz20% Measuring temperature : 202 JIS C 5101-1, 4.8 Test conditions shown in No.2 EIAJ RC-2378, 4.5.4 Measuring frequency : 100 kHz 10% Measuring temperature : 202 JIS C 5101-1, 4.29 Leakage Current Capacitance Shall not exceed the value in No.1. - Shall not exceed the value in No.1. Shall not exceed 10-times of the value in No.1. Shall not exceed 10-times of the value in No.1. Shall not exceed the value in No.1. Within specified tolerances Within - 200 % of value at Step 1 Within 5% of value at Step 1 - Shall not exceed the value in No.3. Shall not exceed the value in No.3. Shall not exceed the value in No.3. - 202 -553 202 852 Within + 500 % of value at Step 1 Shall not exceed 1.5-times of the value in No.3. Shall not exceed the value in No.3. 1052 Derated voltage at 105 202 JIS C 5101-1, 4.26 Test temperature : 85 and 105 Applied voltage : According to the following table Within 5% of value at Step 1 Leakage current : Shall not exceed 3-times of the value in No.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. Rated voltage (VDC) Surge voltage (VDC) 7 Shear Test There shall be no evidence of mechanical damage. 8 Substrate Bending Test 9 Vibration Capacitance : Initial value to remain steady during measurement. Visual Examination : There shall be no evidence of mechanical damage. Capacitance : Initial value to remain steady during measurement. Visual Examination : There shall be no evidence of mechanical damage. 10 Shock There shall be no intermittent contact of 0.5 ms or greater, short, or open. Nor shall there be any spark discharge, insulation breakdown, or evidence of mechanical damage. 11 Solderability 12 Resistance to Soldering Heat Solder shall be in close contact with terminal (pinholes, non-solderability and solder repelling are not allowed). (1) Note (1) : If any question arises relating to the judgment, make sure that the part dipped in solder, more than 3/4 of the terminal surface, is covered with new solder. Leakage Current : Shall not exceed 2-times of the value in No.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed 1.3-times of the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. 13 Component solvent resistance Leakage Current : Shall not exceed the value in No.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed the value in No.3. 14 Solvent resistance of marking Visual examination : After the test the marking shall be legible. 15 Rapid Change of Temperature 16 Damp Heat, Steady State 17 Endurance I 18 Endurance II Leakage Current : Shall not exceed 2-times of the value in No.1. For TCB 6.3V-100F 10A, Leakage Current is less than 3 times of value shown in 6.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed 1.5-times of the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. Leakage Current : Shall not exceed 2-times of the value in No.1. For TCB 6.3V-100F 10A, Leakage Current is less than 3 times of value shown in 6.1. Capacitance change : Within -20% to +40% of the value before test. Dissipation Factor : Shall not exceed 1.5-times of the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. Leakage Current : Shall not exceed 2-times of the value in No.1. For TCB 6.3V-100F 10A, Leakage Current is less than 4 times of value shown in 6.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed 1.5-times of the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. Leakage Current : Shall not exceed 2-times of the value in No.1. For TCB 6.3V-100F 10A, Leakage Current is less than 4 times of value shown in 6.1. Capacitance change : Within 20% of the value before test. Dissipation Factor : Shall not exceed 3-times of the value in No.3. Visual Examination : There shall be no evidence of mechanical damage. 4 2.5 4 6.3 85 3.3 5.2 8.2 10 13 105 2.6 4.2 6.5 10.4 Series protective resistance : 1000 Discharge resistance : 1000 Number of cycles : 1000 cycles JIS C 5101-1, 4.34 Force : 5 N Holding time : 101 sec JIS C 5101-1, 4.35 Bending : 1 mm JIS C 5101-1 4.17 Frequency range : 10-55 Hz Swing width : 1.5 mm Vibration direction : 3 directions with mutually right-angled Duration : 2 hours in each of these mutually erpendicular directions (total 6 hours) Mounting : Solder terminal to the printed board JIS C 5101-1 4.19 Peak acceleration : 490 m/s2 Duration : 11 ms Wave form : Half-sine JIS C 5101-1 4.15 Solder temperature : 2355 Dipping time : 20.5 sec Dipping depth : Terminal shall be dipped into melted solder EIAJ RC-2378, 4.6 IR reflow Preheating : 150 to 200 , 180 sec.(max.) Reflow : 217 ,90 sec.(max.) Peak : 260 5sec.(max.) Number of cycles : 2 JIS C 5101-1 4.31 Temperature : 235 Dipping time : 50.5 min. Conditioning : JIS C 0052 method 2 Solvent : 2-proparol (Isopropyl alcohol) JIS C 5101-1 4.32 10 Temperature : 235 Dipping time : 50.5 min. Conditioning : JIS C 0052 method 2 Solvent : 2-proparol (Isopropyl alcohol) JIS C 5101-1, 4.16 Step 1 : -553 , 303 min + 10 Step 2 : 25 - 5 , 3 min or less Step 3 : 1052 , 303 min + 10 Step 4 : 25 - 5 , 3 min or less Number of cycles : 5 JIS C 5101-1, 4.21 Temperature : 402 Moisture : 90 to 95% RH + 24 Duration : 500 0 hrs JIS C 5101-1, 4.23 Test temperature : 852 Applied voltage : Rated voltage + 48 Duration : 1000 0 hrs JIS C 5101-1, 4.23 Test temperature : 1052 Applied voltage : Derated voltage Duration : 1000 + 480 hrs FREQUENCY CHARACTERISTICS Type TCB 6.3VDC-47F 10S-case, Sample5pcs Impedance&ESR() 100 10 Impedance 0.1 ESR 0.01 0.1 1 10 100 requency(kHz) 1000 10000 Type TCB 6.3VDC-100F 12A-case, Sample5pcs 1000 Impedance&ESR() 100 10 Impedance 1 0.1 ESR 0.01 0.1 1 10 100 requency(kHz) 5 1000 10000 CHARACTERISTICS AT HIGH AND LOW TEMPERATURE TCB 6.3VDC-47F 10S-Case, Sample5pcs 50 Max. Mean 40 Capacitance Change() Min. 30 20 10 0 100 -10 -20 -60 -40 -20 0 20 40 60 80 100 120 Leakage Current () Dissipation factor Temperature() 10 0.20 0.15 0.10 0.05 0.000 -60 -40 -20 0 20 40 Temperature() 60 80 100 120 1 ESR() 0.20 0.1 0.15 0.10 0.05 0 0.00 -60 0.01 -40 -20 0 20 40 Temperature() 60 80 100 120 0 20 40 60 80 100 120 Temperature() 0 0 DAMP HEAT STEADY STATE 40 , 95%RH TCB 6.3VDC-47F 10S-case Snmple : 50pcs Capacitance hange (%) 40 30 Max. 20 Mean Min. 10 0 -10 -20 Dissipation factor 0.25 0.20 0.15 0.10 0.05 0.000 1 1.0 ESR( ) 0.8 0.6 0.4 0.2 Leakage current (mA) 0 100 10 1 0.1 0.01 INITIAL VALUE REFLOW 260 peak 100 Time (Hours) 6 1000 ENDURANCE 85 RATED VOLTAGE Dissipation factor Capacitance hange (%) TCB 6.3VDC-47F 10S-case Sample50pcs 20 15 10 5 0 -5 -10 -15 -20 0.25 Max. Mean Min. 0.20 0.15 0.10 0.05 0 0.00 1.01 ESR( ) 0.8 0.6 0.4 0.2 Leakage current (mA) 0 100 10 1 0.1 0.01 INITIAL VALUE REFLOW 260 peak 100 1000 10000 Time (Hours) ENDURANCE 105 DERATED VOLTAGE Capacitance hange (%) TCB 6.3VDC-47F 10S-case Sample50pcs 20 15 10 5 0 -5 -10 -15 -20 Max. Mean Min. Dissipation factor 0.25 0.20 0.15 0.10 0.05 0 0.00 1 1.0 ESR( ) 0.8 0.6 0.4 0.2 Leakage current (mA) 0 100 10 1 0.1 0.01 INITIAL VALUE REFLOW 260 peak 100 Time (Hours) 7 1000 10000 Application Notes for Tantalum Solid Electrolytic Capacitor with Conductive Polymer 1. Operating voltage 6. Soldering The capacitors shall be operated at the rated voltage or lower. Over rated voltage applied even for a short time may cause short failure. When designing the circuit, the equipment's required reliability must be considered and appropriate voltage derating must be performed. * Recommended operating voltage : 80% or less of the rated voltage * When the operating temperature exceeds 85 , derate the applied voltage. The voltage derating formula is shown below. 6.1 Preheating To obtain optimal reliability, lowering the heat shock during the soldering process is favorable. Capacitors should be pre-heated at 130-160 for approximately 60 seconds. 6.2 Soldering The body of the capacitor should not exceed 260 during soldering. Leakage current can be increased slightly due to the soldering heat. In this case, leakage current will be decreased gradually when leaving capacitors in the normal temperature and humidity adequately. (1) Reflow Soldering Reflow soldering is a process in which the capacitors are mounted on a printed circuit board with solder paste. Two methods of Reflow Soldering: Direct and Atmospheric Heat. * Direct Heat (Hot plate) * Atmospheric Heat a) Near and Far IR Ray b) Convection Oven Vapor Phase Soldering and Flow Soldering are not recommended. Recommended condition by IR Re-flow procedure is shown in picture-1. Pictuere-1 Derating voltage Vt at any temperature T between 85 and 105 shall be calculated by the follwing formula. Derated voltage Voltage (V) Vr Vd Vt = Vr- 0 -55 0 20 85 Vr-Vd 20 (T-85) Vr : Rated voltage Vd : Derating voltage at 105 105 Temperature Rated voltage (VDC) Derated voltage (VDC) 2.5 2.0 4 3.2 6.3 5.0 10 8.0 Temperature of Boards Surface Vr Vd 2. Application that contain AC Voltage Special attention to the following 3 items. (1) The sum of the DC bias voltage and the positive peak value of the AC voltage should not exceed the rated voltage. (2) Reverse voltage should not exceed the allowable values of the negative peak AC voltage. (3) Ripple voltage should not exceed the allowable values. The permissible ripple current and voltage at about 100 kHz or higher can be determined by the following formula from the permissible power loss for each case size (Pmax value) shown in Table 1 and the specified ESR value. However, when the expected operating temperature is higher than room temperature, determine the permissible values multiplying the Pmax value by the specified multiplier (Table 2). For the permissible values at different frequencies, consult our Sales Department. Number of cycles : 2 7. Solvent cleaning Cleaning by organic solvent may damage capacitor's appearance and performance. However, our capacitors are not effected even when soaked at 20-30 2-propanol for 5 minutes. When introducing new cleaning methods or changing the cleaning term, please consult us. E 2 ESR Z2 Permissible ripple voltage Emax= A2 Temperature Time T1= 150200 A1= 180sec.(max.) T2= 217 A2= 90sec.(max.) T3= 260 A3=5sec.(max.) Time 4. Permissible ripple current Imax= Cooling (2) Soldering Iron Soldering with a soldering iron cannot be recommended due to the lack of consistency in maintaining temperatures and process times. If this method should be necessary, the iron should never touch the capacitor's terminals, and the temperature of the soldering iron should never exceed 350 . The application of the iron should not exceed 3 seconds and 30 watt. (3) Please consult us for other methods. Special attention to the polar character. Reverse Voltage should not be applied. Permissible ripple current Reflow A3 T1 A1 3. Reverse voltage P=I 2xESR or P= Preheat T3 T2 8. Ultrasonic cleaning Ultrasonic cleaning under severe condition may break terminals. Also, from an electrical characteristics aspect, it is unfavorable. Therefore, please do not use ultrasonic cleaning if possible. If the Ultrasonic cleaning process will be used, please note the following. (1) The solvent should not be boiled. (Lower the ultrasonic wave output or use solvent with the high boiling point.) (2) The recommended wattage is less than 0.5 watts per cm2. (3) The cleaning time should be kept to a minimum. Also, samples must be swang in the solvent. Please consult us. P m ax (Arms) ESR P m ax x Z = Imaxx Z (Vrms) ESR 9. Storage I m a x: Permissible ripple current at regulated frequency (Arms : RMS value) E m a x: Permissible ripple voltage at regulated frequency (Vrms : RMS value) P m a x: Permissible power loss (W) E S R: Specified ESR value at regulated frequency () Z : Impedance at regulated frequency () Capacitors should be tightly sealed in moisture prevention bag and stored with supplied reel. Moisture Sensitivity Level Table 3 shows the moisture sensitivity level and the floor life of the dampproof wrapping products. Table 1 Permissible power loss for each case size Case Code PmaxW 09M 0.050 10S,12S 0.065 10A,12A 0.078 Note: Above values are measured at 0.8t glass epoxy board mounting in free air and may be changed depending on the kind of board, packing density, and air convection condition. Please consult us if calculated power loss value is different from above list of P max value. Table 3 MSL&Floor Life JEDEC MSL Floor Life 168hrs.(7days) Less than 30/60%RH Reference IPC/JEDEC J-STD-020C July 2004 3 10. Inapplicable circuits The capacitors may cause nonconformity if they are used on the following circuits. (1) High-impedance voltage holding circuits (2) Coupling circuits (3) Time constant circuits (4) Circuits significantly affected by leakage current Table 2 Pmax multiplier at each operating temperature Operating temperature() 20 55 85 105 Multiplier 1.0 0.9 0.8 0.4 If a short circuit occurs, the capacitors may generate heat or smoke depending on the short-circuit current. When designing a circuit, take the instructions stated herein into consideration, and take as much redundant measures as possible. These application notes are prepared based on the technical report RCR-2368B "Guideline of notabilia for fixed tantalum electrolytic capacitors with solid electrolyte for use in electronic equipment" issued by Japan Electronics and Information Technology Industries Association. For the details of the instructions (explanation, reasons and concrete examples), please refer to this guideline, or consult our Sales Department. 5. Non Polar Connection The capacitor cannot be used as a non-polar unit. R MATSUO MATSUO ELECTRIC CO., LTD. P leas e f eel f ree t o as k o ur S ales D ep art ment f o r mo re inf ormation o n Tant alum S o lid E lec t roly tic Cap ac it o r wit h Co nd uc t iv e Po lymer. Overseas Sales Dep. Head office URL 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0883 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0871 http://www.ncc-matsuo.co.jp/ Fax : 06-6332-0920 Fax : 06-6331-1386 Specifications on this catalog are subject to change without prior notice. Please inquire of our Sales Department to confirm specifications prior to use. 8