Semiconductor Components Industries, LLC, 2004
December, 2004 − Rev. 6 1Publication Order Number:
MBRS1100T3/D
MBRS1100T3, MBRS190T3
Preferred Devices
Schottky Power Rectifier
Surface Mount Power Package
Schottky Power Rectifiers employ the use of the Schottky Barrier
principle in a large area metal-to-silicon power diode. State-of-the-art
geometry features epitaxial construction with oxide passivation and
metal overlay contact. Ideally suited for low voltage, high frequency
rectification, or as free wheeling and polarity protection diodes, in
surface mount applications where compact size and weight are critical
to the system. These state-of-the-art devices have the following
features:
Features
•Pb−Free Packages are Available
•Small Compact Surface Mountable Package with J-Bend Leads
•Rectangular Package for Automated Handling
•Highly Stable Oxide Passivated Junction
•High Blocking Voltage − 100 Volts
•150°C Operating Junction Temperature
•Guardring for Stress Protection
Mechanical Characteristics
•Case: Epoxy, Molded
•Weight: 95 mg (approximately)
•Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
•Lead and Mounting Surface Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
•Shipped in 12 mm Tape and Reel, 2500 units per reel
•Cathode Polarity Band
MAXIMUM RATINGS
Rating Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage MBRS190T3
MBRS1100T3
VRRM
VRWM
VR90
100
V
Average Rectified Forward Current
TL = 120°C
TL = 100°C
IF(AV) 1.0
2.0
A
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions
Halfwave, Single Phase, 60 Hz)
IFSM 50 A
Operating Junction Temperature TJ−65 to +150 °C
Voltage Rate of Change dv/dt 10 V/ns
Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits
are exceeded, device functional operation is not implied, damage may occur
and reliability may be affected.
SMB
CASE 403A
PLASTIC
SCHOTTKY BARRIER
RECTIFIER
1.0 AMPERE
90, 100 VOLTS
Preferred devices are recommended choices for future use
and best overall value.
MARKING DIAGRAM
AYW
B1x
http://onsemi.com
B1 = Device Code
x = 9 or C
A = Assembly Location
Y = Year
W = Work Week
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
ORDERING INFORMATION
MBRS1100T3, MBRS190T3
http://onsemi.com
2
THERMAL CHARACTERISTICS
Rating Symbol Value Unit
Thermal Resistance − Junction−to−Lead (TL = 25°C) RJL 22 °C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 1) (iF = 1.0 A, TJ = 25°C) VF0.75 V
Maximum Instantaneous Reverse Current (Note 1)
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 100°C)
IR0.5
5.0
mA
1. Pulse Test: Pulse Width = 300 s, Duty Cycle ≤2.0%.
ORDERING INFORMATION
Device
Marking
Package
Shipping†
Device Marking Package Shipping
†
MBRS1100T3 B19 SMB 2500 Tape & Reel
MBRS1100T3G B19 SMB
(Pb−Free) 2500 Tape & Reel
MBRS190T3 B1C SMB 2500 Tape & Reel
MBRS190T3G B1C SMB
(Pb−Free) 2500 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MBRS1100T3, MBRS190T3
http://onsemi.com
3
TYPICAL ELECTRICAL CHARACTERISTICS
Figure 1. Typical Forward Voltage Figure 2. Typical Reverse Current*
Figure 3. Power Dissipation Figure 4. Current Derating, Lead
20
10
5
2
1
0.5
0.2
0.1
0.05
0.02 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
vF, INSTANTANEOUS VOLTAGE (VOLTS)
100°C
25°C
i , INSTANTANEOUS FORWARD CURRENT (AMPS)
F
1 K
400
200
100
40
20
10
4
2
1
0.4
0.2
0.1
0.04
0.01
0.02
0 102030405060708090100
TJ = 150°C
125°C
100°C
VR, REVERSE VOLTAGE (VOLTS)
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
00 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
TJ = 100°C
SQUARE
WAVE
DC
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
P , AVERAGE POWER DISSIPATION (WATTS)
F(AV)
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
00 20 40 60 80 100 120 140 160
RATED VR APPLIED
RJL = 22°C/W
TJ = 100°C
SQUARE
WAVE
DC
TL, LEAD TEMPERATURE (°C)
I , AVERAGE FORWARD CURRENT (AMPS)
F(AV)
TJ = 150°C
IR, REVERSE CURRENT ( A)µ
*The curves shown are typical for the highest voltage device in the voltage
grouping. Typical reverse current for lower voltage selections can be estimated
from these curves if VR is sufficient below rated VR.
25°C
TYPICAL ELECTRICAL CHARACTERISTICS
Figure 5. Typical Capacitance
280
260
240
220
200
180
160
140
120
100
80
60
40
20
00.1 0.2 0.5 1 2 5 10 20 50 100
VR, REVERSE VOLTAGE (VOLTS)
C, CAPACITANCE (pF)
NOTE: TYPICAL CAPACITANCE
NOTE: AT 0 V = 270 pF
MBRS1100T3, MBRS190T3
http://onsemi.com
4
PACKAGE DIMENSIONS
SMB
PLASTIC PACKAGE
CASE 403A−03
ISSUE D
A
S
DB
J
P
K
C
H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. D DIMENSION SHALL BE MEASURED WITHIN
DIMENSION P.
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.160 0.180 4.06 4.57
B0.130 0.150 3.30 3.81
C0.075 0.095 1.90 2.41
D0.077 0.083 1.96 2.11
H0.0020 0.0060 0.051 0.152
J0.006 0.012 0.15 0.30
K0.030 0.050 0.76 1.27
P0.020 REF 0.51 REF
S0.205 0.220 5.21 5.59
mm
inches
SCALE 8:1
2.743
0.108
2.159
0.085
2.261
0.089
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
MBRS1100T3/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
