o30mm Switches & Pilot Lights o30 o30 Series Switches & Pilot Lights (Selection Guide) Function HN Series Emergency Stop Switch XN Series Emergency Stop Switch Plastic Bezel Pushlock Pull/Turn Reset Category Flush Bezel Pushlock Pull/Turn Reset Padlockable Pushlock Turn Reset - Pushlock Turn Reset o60mm Mushroom Shape Model XN1E-BV4 XN1E-LV4 XN1E-TV4 XN1E-BV5 XN5E-BV4 XN5E-LV4 XN5E-TV4 XN4E-BL4 XN4E-LL4 XN4E-TL4 HN1E-BV4 HN1E-LV4 Page 7 7 8 9 14 Function Pushbutton Extended with Half Shroud Extended Momentary/Maintained Flush Category Extended with Full Shroud Shape Model ABN1 AON1 (Diecast) ABD1 AOD1 ABN2 AON2 (Diecast) ABD2 AOD2 ABN2G AON2G (Diecast) ABGD2 AOGD2 ABN2F AON2F (Diecast) ABFD2 AOFD2 Page 21 74 21 74 21 74 21 74 Function Pushbutton Mushroom with Full Shroud Mushroom Category Palm Mushroom Momentary/Maintained Jumbo Mushroom with Shallow Shroud Jumbo Mushroom with Deep Shroud Momentary Shape Model ABN3 AON3 (Diecast) ABD3 AOD3 ABN3G (Diecast) ABGD3 AOGD3 ABN4 (Diecast) ABD4 ABN4G (Diecast) ABGD4 ABN4F (Diecast) ABFD4 Page 22 75 22 75 22 75 22 75 22 75 Function Category Pushbutton Mushroom Pushlock Turn Reset Mushroom Push Turn Lock Mushroom Pushlock Key Reset Shape 2 Model AVN3 (Diecast) AVD3 AJN3 (Diecast) AJD3 ABN3K Page 23 76 23 76 23 o30 Series Switches & Pilot Lights (Selection Guide) o30 Function Pushbutton Category Pin Lock Mushroom Pull Mushroom Push-Pull Square Flush Momentary Shape Model (Diecast) ABD8P ATN23 (Diecast) AZD3 ATN21 ATN22 (Diecast) AYD31 UBQN1 Page 76 24 76 24 76 22 Function Pushbutton Twin Maintained Pushbutton Square Extended Momentary Square Twin Momentary Square Twin Maintained Flush Twin Maintained Mushroom Twin Maintained Model UBQN2 UWQN1 UWQN2 ABBN11 ABBN33 Page 22 25 25 25 25 Category Shape Function Pilot Light (LED) Category Dome Square Rectangular (Marking) Shape Model APN1 APNE1 (Diecast) APD1 APDE1 UPQN3B UPQN4 UPQNE4 Page 26 77 27 27 3 o30 o30 Series Switches & Pilot Lights (Selection Guide) Function Illuminated Pushbutton (LED) Extended with Half Shroud Extended Category Extended with Full Shroud Mushroom Mushroom Pushlock Turn Reset Momentary/Maintained Shape Model ALN2 ALNE2 AOLN2 AOLNE2 Page 29 (Diecast) ALD2 AOLD2 ALGN2 ALGNE2 AOLGN2 AOLGNE2 ALFN2 ALFNE2 AOLFN2 AOLFNE2 30 31 78 Function Illuminated Pushbutton (LED) Category Mushroom Push Turn Lock (Diecast) ALFD2 AOLFD2 79 ALN3 ALNE3 AOLN3 AOLNE3 (Diecast) ALD3 AOLD3 32 80 Shape Model AJLN3 Page 33 Function Selector Switch Category Knob Illuminated Selector Switch Lever Key Knob Shape 4 Model ASN ASTN (Diecast) ASD Page 34, 41 82 ASNL ASTNL 36, 42 (Diecast) ASDL ASNK ASTNK (Diecast) ASDK ASLN (Diecast) ASLD 83 38, 43 84 44 85 AVLN3 AVLNE3 (Diecast) AVLD3 AVLDE3 33 81 o30 Series Switches & Pilot Lights (Selection Guide) o30 Function Selector Pushbutton Category Ring Mono-Lever Switch Lever Standard Interlocking Shape Model ABN (Diecast) ASBD2 ABNL (Diecast) ASBD2L ARN ARNS ARNL Page 46 87 46 87 48 48 Enclosed Spring Return Enclosed Function Category Cam Switch Knob Key (ACSNO only) (ACSNK only) Model ACSNO ACSSO ACSNK ACSSK UCSQO UCSQM Page 51 51 51 51 Shape 5 o30 XN Series Emergency Stop Switches o30 mm, 4-contact Emergency Stop Switch. Padlockable and flush bezel are available. * Padlockable, flush bezel, o60mm jumbo mushroom, illuminated, LED push-on are available. * IDEC's original "Safe break action" and reverse energy structure ensure the highest level of safety. * Safety lock mechanism (IEC 60947-5-5, 6.2) * Direct opening action mechanism (IEC 60947-5-5, 5.2, IEC60947-5-1, Annex K) * Short depth behind the panel - only 47.7 mm for 4-contact, illuminated (flush bezel: 60.4 mm, padlockable: 61.4 mm) * Padlockable can be locked using padlocks when latched (main contact: OFF). The rugged aluminum diecast shroud allows for installing a maximum of 20 padlocks using a hasp (total weight: 1500g maximum). * Gold-plated silver contacts. * Red (Munsell 5R4/12) or bright red (Munsell 7.5R4.5/14) colors are available. Standards Specifications Applicable Standards Mark File No. or Organization UL508 CSA C22.2 No. 14 UL/c-UL File No. E68961 (padlockable only) IEC60947-5-5 UL991 NFPA79 UL Listing File No. E305148 GB14048.5 IEC60947-5-1, EN60947-5-1 IEC60947-5-5, EN60947-5-5 JIS C8201-5-1, UL508, UL991, NFPA79 CSA C22.2 No. 14, GB14048.5 Operating Temperature Non-illuminated: -25 to +60C (no freezing) Illuminated: -25 to +55C (no freezing) Storage Temperature -45 to +80C Operating Humidity 45 to 85% RH (no condensation) TUV SUD 4.0 mm EU Low Voltage Directive Minimum Operator Stroke Required for Direct Opening Action Maximum Operator Stroke 4.5 mm Contact Resistance 50 m maximum (initial value) Insulation Resistance 100 M minimum (500V DC megger) Overvoltage Category II Impulse Withstand Voltage 2.5 kV Pollution Degree 3 Operating Frequency 900 operations/hour Shock Resistance Operating extremes: 150 m/s2 Damage limits: 1000 m/s2 Vibration Resistance Operating extremes: 10 to 500 Hz, amplitude 0.35 mm, acceleration 50 m/s2 Damage limits: 10 to 500 Hz, amplitude 0.35 mm, acceleration 50 m/s2 Mechanical: 250,000 operations minimum Electrical: 100,000 operations minimum 250,000 operations minimum (24V AC/DC, 100 mA) CCC No. 2008010305290010 Contact Ratings NC main contacts (black)/NO monitor contacts (blue) Rated Insulation Voltage (Ui) 250V Rated Thermal Current (Ith) Rated Operating Voltage (Ue) Rated Operating Current Applicable Standards Minimum Force Required for 80N Direct Opening Action EN60947-5-5 Resistive Load (AC-12) AC 50/60 Hz Inductive Load (AC-15) Main Contacts Resistive Load (DC-12) DC Inductive Load (DC-13) Resistive Load (AC-12) AC 50/60 Hz Inductive Load (AC-14) Monitor Contacts Resistive Load (DC-12) DC Inductive Load (DC-13) Contact Material 5A 30V 125V 250V - 5A 3A - 3A 1.5A 2A 0.4A 0.2A Durability (at 900 operations/h, on-duration 40%) 1A 0.22A 0.1A Degree of Protection Operator: Terminal: - 1.2A 0.6A Short-circuit Protection 250V/10A fuse (Type aM, IEC60269-1/IEC60269-2) Conditional Short-circuit Current 1000A Terminal Style M3 screw terminal Recommended Tightening Torque for Terminal Screw 0.6 to 1.0 N*m Recommended Tightening Torque for Locking Ring 2.5 N*m Applicable Wire Size 0.75 to 1.25 mm2 (AWG18 to 16) Total Weight of a Hasp and Padlocks 1500g maximum (padlockable) Reinforced Insulation (IEC 60664-1) Between live part and metal bezel (flush bezel, padlockable) Weight 83g (XN1E-LV404Q4MR) 93g (XN1E-BV504MR) 89g (XN5E-LV404Q4MR) 120g (XN4E-LL404Q4MR) - 0.6A 0.3A 2A 0.4A 0.2A 1A 0.22A 0.1A Gold-plated Silver * Minimum applicable load: 5V AC/DC, 1 mA (reference value) (May vary depending on the operating conditions and load types.) * The rated operating currents are measured at resistive/inductive load types specified in IEC 60947-5-1. Illumination Ratings (LED) 6 Direct Opening Action Rated Voltage Operating Voltage Rated Current 24V AC/DC 24V AC/DC 10% 15 mA IP65 (IEC60529) IP20 (when XW9Z-VL2MF is installed) XN XN Series Emergency Stop Switches o30 Plastic Bezel Non-illuminated Pushlock Pull/Turn Reset (Solder Terminal) Shape o40mm Mushroom o60mm Jumbo Mushroom Part No. NC Main Contact NO Monitor Contact IP20 Fingersafe Terminal w/Terminal Cover 1NC -- XN1E-BV401MF XN1E-BV401M 2NC -- XN1E-BV402MF XN1E-BV402M 3NC -- XN1E-BV403MF XN1E-BV403M 4NC -- XN1E-BV404MF XN1E-BV404M 1NC 1NO XN1E-BV411MF XN1E-BV411M 2NC 1NO XN1E-BV412MF XN1E-BV412M 3NC 1NO XN1E-BV413MF XN1E-BV413M 2NC 2NO XN1E-BV422MF XN1E-BV422M 1NC -- XN1E-BV501MF XN1E-BV501M 2NC -- XN1E-BV502MF XN1E-BV502M 3NC -- XN1E-BV503MF XN1E-BV503M 4NC -- XN1E-BV504MF XN1E-BV504M 1NC 1NO XN1E-BV511MF XN1E-BV511M 2NC 1NO XN1E-BV512MF XN1E-BV512M 3NC 1NO XN1E-BV513MF XN1E-BV513M 2NC 2NO XN1E-BV522MF XN1E-BV522M Operator Color Code R: Red RH: Bright red * Specify a color code in place of in the Part No. * Only solid wires can be used on the IP20 fingersafe terminal switches. Illuminated Pushlock Pull/Turn Reset (Solder Terminal) Shape Illumination Rated Voltage o40mm Mushroom LED 24V AC/DC NC Main Contact NO Monitor Contact 1NC 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN1E-LV401Q4MFR XN1E-LV401Q4MR -- XN1E-LV402Q4MFR XN1E-LV402Q4MR 3NC -- XN1E-LV403Q4MFR XN1E-LV403Q4MR 4NC -- XN1E-LV404Q4MFR XN1E-LV404Q4MR 1NC 1NO XN1E-LV411Q4MFR XN1E-LV411Q4MR 2NC 1NO XN1E-LV412Q4MFR XN1E-LV412Q4MR 3NC 1NO XN1E-LV413Q4MFR XN1E-LV413Q4MR 2NC 2NO XN1E-LV422Q4MFR XN1E-LV422Q4MR Operator Color Red only * Only solid wires can be used on the IP20 fingersafe terminal switches. Illuminated Push-ON Pushlock Pull/Turn Reset (Solder Terminal) Shape Illumination Rated Voltage NC Main Contact NO Monitor Contact 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN1E-TV402Q4MFR XN1E-TV402Q4MR 3NC -- XN1E-TV403Q4MFR XN1E-TV403Q4MR 2NC 1NO XN1E-TV412Q4MFR XN1E-TV412Q4MR Operator Color o40mm Mushroom LED 24V AC/DC Red only * Push-ON is illuminated when the operator is latched, and turns off when reset. * Only solid wires can be used on the IP20 fingersafe terminal switches. 7 o30 XN Series Emergency Stop Switches Flush Bezel Non-illuminated Pushlock Pull/Turn Reset (Solder Terminal) Shape o40mm Mushroom Part No. NC Main Contact NO Monitor Contact IP20 Fingersafe Terminal w/Terminal Cover 1NC -- XN5E-BV401MF XN5E-BV401M 2NC -- XN5E-BV402MF XN5E-BV402M 3NC -- XN5E-BV403MF XN5E-BV403M 4NC -- XN5E-BV404MF XN5E-BV404M 1NC 1NO XN5E-BV411MF XN5E-BV411M 2NC 1NO XN5E-BV412MF XN5E-BV412M 3NC 1NO XN5E-BV413MF XN5E-BV413M 2NC 2NO XN5E-BV422MF XN5E-BV422M Operator Color Code R: Red RH: Bright red * Specify a color code in place of in the Part No. * Only solid wires can be used on the IP20 fingersafe terminal switches. Illuminated Pushlock Pull/Turn Reset (Solder Terminal) Shape Illumination Rated Voltage o40mm Mushroom LED 24V AC/DC NC Main Contact NO Monitor Contact 1NC 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN5E-LV401Q4MFR XN5E-LV401Q4MR -- XN5E-LV402Q4MFR XN5E-LV402Q4MR 3NC -- XN5E-LV403Q4MFR XN5E-LV403Q4MR 4NC -- XN5E-LV404Q4MFR XN5E-LV404Q4MR 1NC 1NO XN5E-LV411Q4MFR XN5E-LV411Q4MR 2NC 1NO XN5E-LV412Q4MFR XN5E-LV412Q4MR 3NC 1NO XN5E-LV413Q4MFR XN5E-LV413Q4MR 2NC 2NO XN5E-LV422Q4MFR XN5E-LV422Q4MR Operator Color Red only * Only solid wires can be used on the IP20 fingersafe terminal switches. Illuminated Push-ON Pushlock Pull/Turn Reset (Solder Terminal) Shape Illumination Rated Voltage NC Main Contact NO Monitor Contact 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN5E-TV402Q4MFR XN5E-TV402Q4MR 3NC -- XN5E-TV403Q4MFR XN5E-TV403Q4MR 2NC 1NO XN5E-TV412Q4MFR XN5E-TV412Q4MR Operator Color o40mm Mushroom LED 24V AC/DC * Push-ON is illuminated when the operator is latched, and turns off when reset. * Only solid wires can be used on the IP20 fingersafe terminal switches. 8 Red only XN XN Series Emergency Stop Switches o30 Padlockable Non-illuminated Pushlock Pull/Turn Reset (Padlockable) Shape o44mm Mushroom NC Main Contact NO Monitor Contact Part No. IP20 Fingersafe Terminal Operator Color w/Terminal Cover 1NC -- XN4E-BL401MFRH XN4E-BL401MRH 2NC -- XN4E-BL402MFRH XN4E-BL402MRH 3NC -- XN4E-BL403MFRH XN4E-BL403MRH 4NC -- XN4E-BL404MFRH XN4E-BL404MRH 1NC 1NO XN4E-BL411MFRH XN4E-BL411MRH 2NC 1NO XN4E-BL412MFRH XN4E-BL412MRH 3NC 1NO XN4E-BL413MFRH XN4E-BL413MRH 2NC 2NO XN4E-BL422MFRH XN4E-BL422MRH Bright red only * Only solid wires can be used on the IP20 fingersafe terminal switches. * Padlocks and hasps are not supplied with the emergency stop switches and must be ordered separately. See page 12. Illuminated Pushlock Pull/Turn Reset (Padlockable) Shape Illumination Rated Voltage o44mm Mushroom LED 24V AC/DC NC Main Contact NO Monitor Contact 1NC 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN4E-LL401Q4MFR XN4E-LL401Q4MR -- XN4E-LL402Q4MFR XN4E-LL402Q4MR 3NC -- XN4E-LL403Q4MFR XN4E-LL403Q4MR 4NC -- XN4E-LL404Q4MFR XN4E-LL404Q4MR 1NC 1NO XN4E-LL411Q4MFR XN4E-LL411Q4MR 2NC 1NO XN4E-LL412Q4MFR XN4E-LL412Q4MR 3NC 1NO XN4E-LL413Q4MFR XN4E-LL413Q4MR 2NC 2NO XN4E-LL422Q4MFR XN4E-LL422Q4MR Operator Color Red only * Only solid wires can be used on the IP20 fingersafe terminal switches. * Padlocks and hasps are not supplied with the emergency stop switches and must be ordered separately. See page 12. LED Push-ON Pushlock Pull/Turn Reset (Padlockable) Shape Illumination Rated Voltage NC Main Contact NO Monitor Contact 2NC Part No. IP20 Fingersafe Terminal w/Terminal Cover -- XN4E-TL402Q4MFR XN4E-TL402Q4MR 3NC -- XN4E-TL403Q4MFR XN4E-TL403Q4MR 2NC 1NO XN4E-TL412Q4MFR XN4E-TL412Q4MR Operator Color o44mm Mushroom LED 24V AC/DC Red only * Push-ON is illuminated when the operator is latched, and turns off when reset. * Only solid wires can be used on the IP20 fingersafe terminal switches. * Padlocks and hasps are not supplied with the emergency stop switches and must be ordered separately. See page 12. 9 o30 XN Series Emergency Stop Switches Dimensions .8 w/Terminal Cover +0.5 0 +0 .5 0 47.7 33 o3 0.5 47.7 Panel Cut-out 33 Locking Ring Locking Ring Rubber Gasket M3 Terminal Screws M3 Terminal Screws +0.2 0 x. +0 .5 0 Panel Cut-out Rubber Gasket o4 0 37 37 o4 0 o40 mm Mushroom Panel Thickness 1 to 5 Terminal Cover XW9Z-VL2M Panel Thickness 1 to 5 0 0 o6 .8 +0.2 0 . o3 0.5 +0 .5 0 R0 .8 w/Terminal Cover o3 47.7 33 47.7 Panel Cut-out Rubber Gasket M3 Terminal Screws Illuminated M3 Terminal Screws Push-ON o4 +0.2 0 x. 0.5 Locking Ring Locking Ring 4.8 ma +0 .5 0 20.1 20.1 33.0 18.5 4.8 ma x o60 mm Jumbo Mushroom 18.5 R0 IP20 Fingersafe +0.5 0 Illuminated/Push-ON 33 Panel Cut-out Rubber Gasket o4 0 37 0 37 Push-ON 33 o60 mm Jumbo Mushroom +0.5 33.0 0 33 o40 mm Mushroom o6 IP20 Cover XW9Z-VL2MF Illuminated 4.8 ma 20.1 33.0 18.5 0.5 R0 +0.2 0 . +0.5 0 o3 4.8 ax 33.0 .8m 18.5 R0 20.1 Plastic Bezel Non-illuminated IP20 Fingersafe IP20 Cover XW9Z-VL2MF Terminal Cover XW9Z-VL2M Panel Thickness 1 to 5 Panel Thickness 1 to 5 Flush Bezel o3 +0 .5 0 .8 w/Terminal Cover 60.4 21 Locking Ring Rubber Gasket 4.8 ma x Panel Cut-out 60.4 21 Locking Ring Rubber Gasket 0.5 +0 .5 0 Panel Cut-out M3 Terminal Screws o4 +0.2 0 . o3 20.1 20.1 M3 Terminal Screws R0 33.0 o41 18.5 0.5 +0.2 0 . +0.5 33.0 0 IP20 Fingersafe 4.8 ax o41 .8m 18.5 R0 +0.5 0 Non-Illuminated o4 0 37 37 0 Terminal Cover XW9Z-VL2M Panel Thickness 1 to 5 IP20 Cover XW9Z-VL2MF Panel Thickness 1 to 5 Illuminated/Push-ON 60.4 21 Locking Ring Rubber Gasket M3 Terminal Screws Panel Cut-out o4 0 4.8 ma o3 0.5 +0 .5 0 Push-ON 21 Rubber Gasket M3 Terminal Screws Panel Cut-out o4 0 37 Illuminated 60.4 Locking Ring +0.2 0 x. 20.1 20.1 Push-ON R0 .8 +0.5 33.0 0 +0 .5 0 37 Illuminated w/Terminal Cover 33.0 o41 0.5 +0.2 0 x. o41 o3 18.5 4.8 ma 18.5 R0 .8 +0.5 0 IP20 Fingersafe IP20 Cover XW9Z-VL2MF Panel Thickness 1 to 5 Terminal Cover XW9Z-VL2M Panel Thickness 1 to 5 All dimensions in mm. 10 XN XN Series Emergency Stop Switches o30 Dimensions R0 +0.2 0 .8 x. +0 .5 0 o3 w/Terminal Cover Panel Cut-out 43 61.4 +0 .5 0 Rubber Gasket Panel Cut-out 43 Locking Ring Rubber Gasket 4 o4 M3 Terminal Screws 37 4 o4 M3 Terminal Screws +0.2 0 x. 20.1 33.0 20.1 59.9 61.4 Locking Ring 0.5 4.8 ma +0.5 0 0.5 18.5 IP20 Fingersafe 4.8 ma 33.0 .8 18.5 R0 o3 +0.5 0 Padlockable Non-illuminated .8 o3 +0 .5 0 w/Terminal Cover 59.9 61.4 Panel Cut-out 43 Locking Ring Illuminated Push-ON Terminal Cover XW9Z-VL2M Panel Thickness 1 to 6 LED Unit Internal Circuit +0.5 0 X Plastic Bezel Y R X1 LED 70 mm minimum Flush Bezel * The values shown above are the minimum dimen sions for mounting with other o30 mm pushbuttons. For other switches & pilot lights of different sizes and styles, determine the values according to the dimensions, operation, and wiring convenience. * For padlockable, determine the values according to the size and number of padlocks and hasp. X Rubber Gasket M3 Terminal Screws Panel Thickness 1 to 6 Mounting Hole Layout Y Panel Cut-out 43 Locking Ring 37 IP20 Cover XW9Z-VL2MF o30.5 +0 .5 0 37 M3 Terminal Screws +0.2 0 x. 4 o4 Rubber Gasket 4 o4 Push-ON 0.5 4.8 ma 20.1 20.1 59.9 61.4 Illuminated R0 +0.2 0 x. 33.0 18.5 0.5 4.8 ma 33.0 .8 Panel Thickness 1 to 6 18.5 R0 o3 +0.5 0 Illuminated/Push-ON IP20 Fingersafe Terminal Cover XW9Z-VL2M Panel Thickness 1 to 6 +0.5 0 IP20 Cover XW9Z-VL2MF X2 LED chip Protection Diode Resistor Terminal Arrangement (Bottom View) Illuminated 1NC: Terminals on right 2NC:Terminals on right and left 3NC:Terminals on right, left, and top LED 3 X2 X1 1 22 12 Crimping Terminal 41 11 Left 3 X2 Right 4 Solid Wire o1.2 max. Spade Terminal 6.2 max. 3.0 max. Insulation Tube 4.7 to 5.9 Crimping Terminal Insulation Tube Only solid wire can be used for IP20. Right 21 X1 X2 4.7min. TOP Right 2 2 X1 X2 2NC: Terminals on right and left 3NC:Terminals on right, left, and top Left 1 Right 4 LED LED 1NC: Terminals on top 2NC: Terminals on right and left 6.0 max. 3.2 min. o6.0 max. TOP 3 1 LED * Contact 1-2: NC main contact (black) Ring Terminal 3-4: NO monitor contact (blue) * Contact Number (1-4) o3.2 min. Starting with the contact of TOP side, in a counterclockwise direction. Left 2 Right 4 1 4 2 X1 Left 3 1 X2 Right TOP 2 1 1 1 2 LED 1 1 1NC: Terminals on right 2NC:Terminals on right and left 3NC:Terminals on right, left, and top With 1NO monitor contact (blue) 2 2 2 X1 2 3 1NC: Terminals on top 2NC:Terminals on right and left TOP 1 TOP 2 1 1 4 Left With 2NO monitor contacts (blue) Applicable Crimping Terminal NC main contacts (black) only Left Right 3 Push-ON 1 1 1 Left 2 4 1 1 4 42 2 Right 1 Left 2 Right 1 Left 3 With 1NO monitor contact (blue) TOP TOP 2 2 1 2 1 NC main contacts (black) only 2 TOP 2 2 TOP 1 With 2NO monitor contacts (blue) 2 With 1NO monitor contact (blue) 2 NC main contacts (black) only 2 Non-illuminated 34 33 (Example: 1NO-3NC contact) 4.7 to 5.9 Wire 4.7 to 5.9 Wire * Be sure to install an insulating tube on the crimping terminal. All dimensions in mm. 11 o30 XN Series Emergency Stop Switches Accessories and Replacement Parts Name & Shape Material Part No. Package Quantity Ordering No. Terminal Cover PPE XW9Z-VL2M XW9Z-VL2MPN02 2 * Black * Used to change terminal cover to IP20 fingersafe terminal. * Only solid wires can be used. Once installed, IP20 terminal cover cannot be removed. IP20 Fingersafe Terminal Cover Polyamide XW9Z-VL2MF XW9Z-VL2MFPN02 Remarks * Black * Used for screw terminals. * Attached to IP20 protection cover units. 2 * Used to tighten the locking ring when installing the XN emergency stop switch onto a panel. Ring Wrench 8 o3 Brass XN9Z-T1 XN9Z-T1 1 90 * Used to tighten the locking ring when installing the XN emergency stop switch onto a panel. TWST-T1 1 20.5 TWST-T1 52 Steel Trivalent chromate plating 49.5 Ring Wrench 23.7 77 * The XN series emergency stop switches are supplied with either terminal cover or IP20 fingersafe terminal cover. * Padlocks and hasps are not supplied and must be ordered separately. Nameplates (for o30 Emergency Stop Switches) Description & Shape Legend Part No. (blank) Package Quantity Dimensions (mm) Polyamide Mounting panel thickness XN4E-L4: 1.0 to 4.5 mm XNE-V4: 1.0 to3.5 mm HNAV-0 o60 1 o3 0 EMERGENCY STOP HNAV-27 1.5 1.0 Plate color: Yellow (Munsell 2.5Y 8/10 or equivalent), Legend: Black Padlock and Hasp Padlocks and hasps of the following specifications can be used with padlockable emergency stop switches. Padlock Size A B 7 mm maximum C 19 mm minimum 39 mm minimum D 15 mm minimum (Note) Note: When the padlock is installed from the side of the bezel, dimension D requires a minimum of 6 mm. When the padlock is installed from the front of the button, dimension D requires a minimum of 15 mm. C B A Manufacturer D PANDUIT CORP. 12 Master Lock Part No. PSL-HD3 PSL-1A 420 421 Use only padlocks or hasps that satisfy the specifications shown on the left. The maximum total weight for padlocks and hasps is 1500g. Make sure that the total weight does not exceed 1500g, otherwise the XN emergency stop switch may be damaged. Make sure that locking and unlocking of the padlock and hasp do not interfere with other devices. Padlocks and hasps are available from the following manufacturers. Manufacturer URL PANDUIT CORP. http://www.panduit.com/ Master Lock(R) Company LLC http://www.masterlock.com/ XN XN Series Emergency Stop Switches o30 Operating Instructions Removing the Contact Block First unlock the operator button. Grab the yellow bayonet ring and pull back the bayonet ring until the latch pin clicks , then turn the contact block counter clockwise and pull out . Installing & Removing Terminal Covers Bayonet Ring (yellow) Turn counterclockwise Grab Pull Latch Grab Notes for removing the contact block 1. Do not attempt to remove the contact block while the operator is latched, otherwise the switch may be damaged. 2. When the contact block is removed, the monitor contact (NO contact) is closed. 3. While removing the contact block, do not use excessive force, otherwise the switch may be damaged. 4. An LED lamp is built into the contact block for illuminated pushbuttons. When removing the contact block, pull the contact block straight to prevent damage to the LED lamp. If excessive force is used, the LED lamp may be damaged and fail to light. Rubber Gasket Panel Mounting Operator without thread TOP Marking Remove the locking ring from the operator and check that the rubber gasket is in place. Anti-rotation Insert the operator from Locking Ring Projection panel front into the panel hole. Face the side without thread on the operator with TOP marking upward, and tighten the locking ring using ring wrench XN9Z-T1 or TWST-T1 to a torque of 2.5 N*m maximum. When using a nameplate When using a nameplate HNAV-, break the projection from the nameplate using pliers. Projection Installing the Contact Block First unlock the operator button. Align the small marking on the edge of the operator with the small marking on the yellow bayonet ring. Hold the contact block, not the bayonet ring. Press the contact block onto the operator and turn the contact block clockwise until the bayonet ring clicks. Marking Marking Turn clockwise Push TOP Marking To remove the terminal cover, pull out the two latches on the top side of the terminal cover. Do not exert excessive force to the latches, otherwise the latches may break. TOP Markings Press the terminal cover Projections Slots Place the projections on the contact block. IP20 Fingersafe Terminal Cover XW9Z-VL2MF To install the IP20 fingersafe terminal cover, align the TOP marking on the cover with the TOP marking on the contact block, and press the cover toward the contact block. Notes: 1. Once installed, the XW9Z-VL2MF cannot be removed. 2. With the XW9Z-VL2MF installed, crimping terminals cannot be used. Use solid wires. 3. The XW9Z-VL2MF cannot be installed after wiring. 4. Make sure that the XW9Z-VL2MF is securely installed. IP20 cannot be achieved when installed loosely, and electric shocks may occur. TOP Marking (Pull) Projections TOP Marking TOP Marking (Press) TOP Marking Notes for Operation When using the XN emergency stop switches in safetyrelated part of a control system, observe safety standards and regulations of the relevant country or region. Also be sure to perform a risk assessment before operation. Wiring Tighten the M3 terminal screws to a torque of 0.6 to 1.0 N*m. Contact Bounce When the button is reset by pulling or turning, the NC main contacts will bounce. When pressing the button, the NO monitor contacts will bounce. When designing a control circuit, take the contact bounce time into consideration (reference value: 20 ms). LED Illuminated Switches An LED lamp is built into the contact block and cannot be replaced. Handling Do not expose the switch to excessive shocks and vibra tions, for example by operating the switch with tools. Otherwise the switch may be deformed or damaged, causing malfunction or operation failure. Notes for installing the contact block 1. Do not attempt to install the contact block when the operator is latched, otherwise the switch may be damaged. 2. Make sure that the bayonet ring is in the locked position. 13 o30 HN Series Emergency Stop Switches Emergency Stop Switches (Unibody) Specifications Standards Specifications Applicable Standards Mark UL508 CSA C22.2 No. 14 File No. or Organization UL Listing File No. E55996 TUV SUD EN60947-5-5 EU Low Voltage Directive GB14048.5 CCC No. 2013010305610376 Contact Ratings Rated Insulation Voltage (Ui) 250V Rated Thermal Current (Ith) 10A Rated Operational Voltage (Ue) 24V 110V 220V AC Resistive Load (AC-12) 6A 3A 3A 50/60 Rated Op- Hz Inductive Load (AC-15) 6A 3A 3A erational Resistive Load (DC-12) 6A 2A 1A Current DC Inductive Load (DC-13) 1.5A 0.3A 0.15A Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load (reference value): 3V AC/DC, 5 mA (Applicable range may vary with operating condi tions and load types.) LED Lamp Ratings Operating Temperature -25 to +60C (no freezing) Illuminated units: -25 to +55C Storage Temperature -40 to +80C Operating Humidity 45 to 85% RH (no condensation) Operating Force 50N Minimum Force Required for Direct Opening Action Maximum Operator Stroke 5.5 mm 10 mm Contact Resistance 50 m maximum (initial value) Insulation Resistance 100 M minimum (500V DC megger) Dielectric Strength Between live and dead metal parts Contacts: 2,500V AC, 1 minute Illuminated parts: 1,000V AC, 1 minute Vibration Resistance Damage limits: 30 Hz, amplitude 1.5 mm Operating extremes: 5 to 55 Hz, amplitude 0.5 mm Shock Resistance Damage limits: 1,000 m/s2 Operating extremes: 100 m/s2 Operating Frequency 900 operations/h Life Mechanical: 250,000 operations minimum Electrical: 100,000 operations minimum Degree of Protection Terminal Style IP65 M3.5 screw Weight (approx.) 58g (HN1E-BV402R) 65g (HN1E-LV402Q4R) LED Lamp Rated Operating Voltage of Unit Part No. 24V AC/DC LSTD-2R Rated Voltage 24V AC/DC 10% Rated Current 10 mA Pushlock Turn Reset Switches (Unibody) Shape Contact Part No. 1NO-1NC Button Color HN1E-BV411R Red only 2NC HN1E-BV402R * When pressed, the button is held depressed. The button is released by turning clockwise. * Terminal cover HW-VL7 is supplied with the switch. Illuminated Pushlock Turn Reset Switches (Unibody) Shape Lamp Contact 1NO-1NC Part No. Lens Color HN1E-LV411Q0R Without Lamp Red only 2NC HN1E-LV402Q0R * When pressed, the button is held depressed. The button is released by turning clockwise. * Terminal cover HW-VL7 is supplied with the switch. Maintenance Parts 14 Name Part No. Ordering No. Package Quantity Terminal Cover for HW1E HW-VL7 HW-VL7PN10 10 HN HN Series Emergency Stop Switches o30 Dimensions HN1E-BV4 Panel Cut-Out M3.5 Terminal Screw Gasket R0 Panel Thickness 0.8 to 6 .8 m o3 0 .5 +0. ax. 0 4.8+0.2 33 0 5 0.5 Terminal Arrangement (Bottom View) TOP Marking Side Locking Ring o4 0 23.5 61 63 32 HN1E-LV4 M3.5 Terminal Screw Terminal Arrangement (Bottom View) TOP Marking Side Panel Thickness 0.8 to 6 Gasket M3.5 Terminal Screw Lamp Terminal X1 0.5 Locking Ring o4 0 LAMP X2 23.5 61 63 All dimensions in mm. 32 Accessory Part No. Package Quantity Ring Wrench TWST-T1 1 * Used for tightening the locking nut. * Tighten the locking nut to a torque of 2.0 to 2.5 N*m. 52 Metal (zincplated) Remarks 20.5 Material 49.5 Shape 23.7 77 * Used to tighten the locking ring when installing the XN emergency stop switch onto a panel. Ring Wrench 8 o3 Brass XN9Z-T1 1 90 Nameplates (for o30 Emergency Stop Switches) Shape Part No. HNAV-0 Legend Package Quantity (blank) 1 HNAV-27 EMERGENCY STOP Remarks Background: Yellow Legend: Black Applicable panel thickness: 0.8 to 4.5 mm Material: Polyamide Legend "EMERGENCY STOP" is indicated outside a o44mm circle. o60 o3 0 1.5 1.0 15 o30 Series Switches & Pilot Lights Heavy duty switches & pilot lights offer both variety and reliability Endures harsh environments * Degree of protection: IP65 * UL, CSA approved, and EN compliant. Applicable Standards Mark File No. or Organization UL 508 UL Listing File No. E68961 CSA C22.2 No.14 CSA File No. LR21451 EN60947-5-1 EU Low Voltage Directive GB14048.5 CCC No. 200501030514658 Specifications and Ratings Contact Ratings Contact Block Rated Insulation Voltage Rated Continuous Current Pushbuttons Illuminated Pushbuttons Selector Switches Illuminated Selector Switches Selector Pushbuttons BS/BST (o30 series) 600V 10A Contact Ratings by Utilization Category IEC 60947-5-1 AC-15 (A600) DC-13 (P600) Characteristics Contact Ratings by Utilization Category Operational Voltage Operational Current AC 50/60 Hz DC AC-12 AC-15 DC-12 DC-13 24V 10A 10A 10A 5A Control of resistive loads and solid state loads Control of electromagnetic loads (> 72 VA) Control of resistive loads and solid state loads Control of electromagnets 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types) For mono-levers and cam switches, see pages 47 and 50. BS (BST) Contact Block Contact Blocks Single-pole Contact Block M3.5 Terminal Screw Interlocking Groove Contact BS BST Push Rod Part No. 1NO 1NC 1EM (early make) 1LB (late break) BS010E BST010 Green BS001E BST001 Red BS010SE BST010S Black BS001SE BST001S White BST contact blocks are used for the following switches and are not interchangeable with BS contact blocks. (The BS housing is dark gray and the BST housing is light gray.) Inspection Window Push Rod Mounting Screw * Pushlock turn reset and push turn lock switches * LED illuminated pushbuttons * LED illuminated selector switches * All models of diecast zinc housing swiches & pilot lights * Durable nylon 66 housing has a high resistance against alkalis. * Silver contacts. Gold contact (gold-plated silver) also available. * Up to four blocks in two layers can be mounted onto each operator. 16 o30 o30 Series Switches & Pilot Lights o30 LED Illuminated Unit Specifications Unit Color Code Pilot Light Illuminated Pushbutton Illuminated Selector Switch A: G: PW: R: S: W: Y: amber green pure white red blue white yellow Input Operating Voltage Lamp Base LED Lamp Part No. Voltage 6V AC/DC 10% LSTD-6 12V AC/DC 10% LSTD-1 24V AC/DC 10% LSTD-2 Full Voltage 6V AC/DC 12V AC/DC 24V AC/DC BA9S/13 Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC (50/60 Hz) BA9S/13 LSTD-6 6V AC/DC 10% DC-DC Converter 110V DC BA9S/13 LSTD-6 6V AC/DC 10% Note: Use a pure white (PW) LED for yellow (Y) illumination. LED Lamp Ratings (LSTD) Part No. Lamp Base Rated Voltage Voltage Range AC Current Draw DC LSTD-6 BA9S/13 6V AC/DC 6V AC/DC 10% 8 mA A, R, W: 7 mA G, PW, S: 5.5 mA LSTD-1 LSTD-2 12V AC/DC 12V AC/DC 10% 11 mA 24V AC/DC 24V AC/DC 10% 11 mA 10 mA 10 mA Color Code Lamp Base Color Voltage Marking A (amber), G (green), PW (pure white), R (red), S (blue), W (white) Same as illumination color Die stamped on the base Life (reference value) Approx. 50,000 hours (The luminance is reduced to 50% the initial intensity when used on complete DC.) X1 LED Chip Protection Diode Internal Circuit Zener Diode X2 Resistor Note: Use a pure white (PW) LED for yellow (Y) illumination. 17 o30 o30 Series Switches & Pilot Lights Specifications Operating Temperature -25 to +50C (no freezing) Storage Temperature -40 to +80C (no freezing) Operating Humidity Contact Resistance 45 to 85% RH (no condensation) 50 m maximum (initial value) Insulation Resistance 100 M minimum (500V DC megger) Dielectric Strength Between live and dead metal parts: (Full voltage and pilot lights: Vibration Resistance Operating extremes: 5 to 55 Hz, amplitude 0.5 mm Shock Resistance Damage limits: 1,000 m/s2 Operating extremes: 100 m/s2 Mechanical Life (minimum operations) Pushbuttons Momentary: Maintained: Illuminated pushbuttons Momentary: Maintained: Selector switches: Key selector switches: Illuminated selector switches: Selector pushbuttons: Mono-lever switches: (Interlocking): Pushlock turn reset Mushroom push-pull switch Two contact blocks: Four contact blocks: 2,500V AC, 1 minute 2,000V AC, 1 minute) 5,000,000 500,000 2,500,000 500,000 500,000 500,000 500,000 250,000 500,000 250,000 500,000 500,000 200,000 1 Pushbuttons: 500,000 1 Illuminated pushbuttons: 500,000 2 Selector switches: 500,000 2 Key selector switches: 500,000 2 Illuminated selector switches: 500,000 2 Selector pushbuttons: 250,000 3 Mono-lever switches: 500,000 3 (Interlocking): 250,000 1 Switching frequency 1,800 operations/h, duty ratio 40% 4 2 Switching frequency 1,200 operations/h, duty ratio 40% 3 Switching frequency 900 operations/h, duty ratio 40% 4 Switching frequency 900 operations/h for square twin or twin maintained Electrical Life (minimum operations) Degree of Protection Part No. Unit IEC 60529 Pushbuttons, pilot lights, illuminated pushbuttons, selector switches, selector pushbuttons, mono-lever switches, and cam switches (ACSNO/ACSSO) A IP65 Illuminated selector switches, key pushbuttons, key reset pushbuttons, key cam IP54 switches, and key selector switches Square pushbuttons, square pilot lights, and cam switches (UC) U IP40 Note: (3S) of NEMA ICS 6-110 applies to the pilot lights with round lens. Mounting Hole Layout (Twin Maintained) R0.8 max. o3 4.8 +0 . 0 5 50 0.5 +0.2 0 33 +0.5 0 +0 . 0 5 33 +0.5 0 Round Unit: 42 Square Unit: 55 0.5 R0.8 max. 4.8 +0.2 0 o3 The minimum mounting centers are applicable to switches with one layer of contact blocks (two contact blocks). When two layers of contact blocks (four contact blocks) are mounted, determine the minimum mounting centers in consideration of convenience for wiring. * Mushroom with shroud: 50 mm minimum * Jumbo mushroom: 67 mm minimum * Jumbo mushroom with shroud: 76 mm minimum * Square twin: 55 mm minimum * Selector switch with lever: 50 mm minimum The 4.8 mm recess is for preventing rotation and is not neces sary when the nameplate or anti-rotation ring is not used. 50 Note: For mounting hole layout of pushbuttons, mono-lever switches, and cam switches, see each section. 18 o30 o30 Series Switches & Pilot Lights (Ordering Information) o30 Ordering Information Standard Units Terminal Cover * Specify an operator or Lens/LED Color Code in the Part No. * Black, green, and red buttons are included with flush pushbuttons. * Terminal covers, nameplates, and accessories are ordered separately. * When a terminal cover is required, order an applicable terminal cover referring to page 59. The Part No. development charts shown below can be used to specify switches and pilot lights other than those listed on the following pages. Gold-plated silver contacts are also available. o30 Series Pushbuttons ABN2 11 R - MAU Optional contact MAU: Gold-plated silver contact Button color code Contact configuration 10: 1NO 01: 1NC 11: 1NO-1NC 20: 2NO 02: 2NC 22: 2NO-2NC 40: 4NO 04: 4NC 13: 1NO-3NC 31: 3NO-1NC 30: 3NO 03: 3NC 12: 1NO-2NC 21: 2NO-1NC Note: * Mushroom pull ATN23 can have a maximum of two contact blocks. * Mushroom push-pull return ATN22 cannot have only NO or only NC contacts. * No other contact configurations are available for square twin UWQN1 than those specified in this catalog. o30 Series Illuminated Pushbuttons ALFN2 126 13 D N R - MAU Optional contact MAU: Gold-plated silver contact Lens/LED Color Code Contact configuration 11:2 1NO-1NC 20: 2NO 02:2 2NC 31: 3NO-1NC 22:2 2NO-2NC 13: 1NO-3NC 40:2 4NO 04: 4NC Operating voltage code Note: * Illuminated pushbuttons cannot have an odd number of contact blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and 3NC. o30 Series Pilot Lights APN1 116 D R Lens/LED Color Code Operating voltage code Note: * LED lamps cannot be used on 480V AC transformers. 19 o30 o30 Series Switches & Pilot Lights (Ordering Information) o30 Series Selector Switch o30 Series Illuminated Selector Switch ASN 2 L 11 - MAU ASLN 2 16 22 D N R - MAU Optional contact MAU: Gold-plated silver contact Contact configuration Operator (blank): Knob L: Lever Operator position code o30 Series Key Selector Switch ASN 2 K 11 D - MAU Optional contact MAU: Gold-plated silver contact Key removable position code 2-position * Maintained (blank): Removable in all positions B: Removable in left only C: Removable in right only * Spring return from right (blank): Removable in left only * Spring return from left (blank): Removable in right only 3-position * Maintained (blank): Removable in all positions B: Removable in left and center C: Removable in right and center D: Removable in center only E: Removable in right and left G: Removable in left only H: Removable in right only * Spring return from right (blank): Removable in left and center D: Removable in center only G: Removable in left only * Spring return from left (blank): Removable in right and center D: Removable in center only H: Removable in right only * Spring return two-way (blank): Removable in center only Contact configuration Operator position code Note: * The key cannot be removed in the return position. 20 Optional contact MAU: Gold-plated silver contact Lens/LED Color Code Contact configuration Operating voltage code Number of positions o30 o30 Series Pushbuttons o30 Flush / Extended / Extended w/Half Shroud / Extended w/Full Shroud Pushbuttons Package Quantity: 1 Flush AON1 Maintained (nameplate sold separately) AON110 1NC AON101 1NO-1NC AON111 2NO AON120 2NC AON102 Specify S, W, or Y when a blue, white, or yellow button is required. (nameplate sold separately) ABN210 1NC ABN201 91 (3 to 4 blocks) (nameplate sold separately) ABN220 2NC ABN202 1NO AON210 1NC AON201 (nameplate sold separately) 46 (1 or 2 blocks) Maintained (nameplate sold separately) 2NO AON220 2NC AON202 ABN2G10 1NC ABN2G01 1NO-1NC ABN2G11 2NO ABN2G20 2NC ABN2G02 1NO AON2G10 1NC AON2G01 1NO-1NC AON2G11 2NO AON2G20 2NC AON2G02 1NO ABN2F10 1NC ABN2F01 91 (3 to 4 blocks) M3.5 Terminal Screw Specify a button color code in place of in the Part No. B: G: R: S: W: Y: black green red blue white yellow 15.5 Panel Thickness 0.8 to 4 23 6 40 42 (1 or 2 blocks) 20.5 65 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 4 23 6 40 64 (1 or 2 blocks) 87 (3 or 4 blocks) M3.5 Terminal Screw 20.5 Panel Thickness 0.8 to 7.5 1NO-1NC ABN2F11 2NO ABN2F20 6 ABN2F02 1NO AON2F10 1NC AON2F01 23 46 (1 or 2 blocks) 40 17 69 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 1NO-1NC AON2F11 2NO AON2F20 2NC AON2F02 2NO-2NC AON2F22 o25 Maintained 40 68 (1 to 2 blocks) 9 2NO-2NC ABN2F22 Extended with Full Shroud AON2F 23 6 o25 o27 o35 1NO 2NC (nameplate sold separately) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw o25 o28.5 Momentary 15.5 69 (3 or 4 blocks) 2NO-2NC AON2G22 Extended with Full Shroud ABN2F 40 9 1NO-1NC AON211 2NO-2NC ABN2G22 Extended with Half Shroud AON2G 23 6 o25 o27 o35 Momentary Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 2NO-2NC AON222 Extended with Half Shroud ABN2G 9 o25 Maintained 40 68 (1 to 2 blocks) 1NO-1NC ABN211 2NO 36 23 6 2NO-2NC ABN222 Extended AON2 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw o25 Momentary 1NO 9 69 (3 or 4 blocks) 2NO-2NC AON122 Extended ABN2 (nameplate sold separately) 1NO 40 46 (1 or 2 blocks) 36 2NO-2NC ABN122 23 6 36 ABN102 36 2NC Black (B), green (G), and red (R) buttons are sup plied with each unit. 36 ABN120 36 2NO 36 1NO-1NC ABN111 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 23 36 ABN101 o35 ABN110 1NC o35 (nameplate sold separately) 1NO Dimensions (mm) Code o35 Momentary Part No. o35 Flush ABN1 Contact o35 Operation o28.5 o35 Shape Button Color 40 68 (1 or 2 blocks) 91 (3 or 4 blocks) 17 * Round bezel and shroud (metal): Chrome-plated * Other contact configurations and gold-plated silver contacts are also available. See page 19. 21 o30 o30 Series Pushbuttons Mushroom / Jumbo Mushroom / Square Flush / Square Extended Pushbuttons Package Quantity: 1 Maintained (nameplate sold separately) 1NO-1NC ABN311 2NO ABN320 2NC ABN302 46 (1 or 2 blocks) 2NO-2NC ABN322 69 (3 or 4 blocks) 1NO AON310 1NC AON301 1NO-1NC AON311 2NO AON320 2NC AON302 Palm Mushroom ABN4 Momentary 1NC ABN3G01 black green red blue white yellow 23 6 91 (3 or 4 blocks) 1NO-1NC ABN3G11 2NO ABN3G20 2NC ABN3G02 44 (1 or 2 blocks) 2NO-2NC ABN3G22 67 (3 or 4 blocks) 1NO ABN410 1NC ABN401 6 2NO ABN420 2NC ABN402 1NO ABN4G10 1NC ABN4G01 1NO-1NC ABN4G11 2NO ABN4G20 2NC ABN4G02 1NO ABN4F10 1NC ABN4F01 2NO 6 35 69 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: black G: green R: red 6 23 46 (1 or 2 blocks) 28 69 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 ABN4F02 69 (3 or 4 blocks) UBQN110 1NC UBQN101 M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 34 1NO 23 46 (1 or 2 blocks) 32.5 1NO-1NC UBQN111 UBQN120 UBQN102 1NO UBQN210 1NC UBQN201 6 B: G: R: Y: black green red yellow 23 47.5 (1 or 2 blocks) 40 14 44 70.5 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 34 2NO 1NO-1NC UBQN211 2NO UBQN220 2NC UBQN202 2NO-2NC UBQN222 * Specify a button color code in place of in the Part No. * Round/square bezel and shroud (metal): Chrome-plated * Other contact configurations and gold-plated silver contacts are also available. See page 19. 22 23 46 (1 or 2 blocks) ABN4F20 2NO-2NC UBQN122 Momentary Panel Thickness 0.8 to 7.5 1NO-1NC ABN4F11 2NC Square Extended UBQN2 23 M3.5 Terminal Screw 2NO-2NC ABN4F22 Momentary 23 1NO-1NC ABN411 2NC Square Flush UBQN1 Panel Thickness 0.8 to 6.5 o75 Momentary 21 M3.5 Terminal Screw 2NO-2NC ABN4G22 Jumbo Mushroom with Deep Shroud ABN4F 40 68 (1 or 2 blocks) o65 Momentary Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: G: R: S: W: Y: 2NO-2NC ABN422 Jumbo Mushroom with Shallow Shroud ABN4G 21 o48 ABN3G10 40 o74 Momentary 1NO 23 6 2NO-2NC AON322 Mushroom with Full Shroud ABN3G Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 36 ABN301 36 Mushroom AON3 ABN310 1NC 36 52.2 (nameplate sold separately) 1NO Dimensions (mm) Code 36 52.2 Momentary Part No. o40 Mushroom ABN3 Contact o40 Operation o75 Shape Button Color 6 23 47.5 (1 or 2 blocks) 70.5 (3 or 4 blocks) 20 40 44 o30 o30 Series Pushbuttons o30 Pushlock Turn Reset / Pushlock Key Reset / Push Turn Lock / Key ON/OFF Lock / Toggle Lever Pushbuttons Package Quantity: 1 AVN311N 2NO AVN320N 2NC AVN302N 2NO-2NC AVN322N 1NO ABN3K10 1NC ABN3K01 1NO-1NC ABN3K11 2NO ABN3K20 2NC ABN3K02 2NO-2NC ABN3K22 AJN310N 1NC AJN301N 1NO-1NC AJN311N 2NO AJN320N 2NC AJN302N 2NO-2NC AJN322N 5.5 23 53 (1 or 2 blocks) 40 24 76 (3 or 4 blocks) M3.5 Terminal Screw B: G: R: Y: black green red yellow FR Panel Thickness 0.8 to 7.5 EE 23 6 53 (1 or 2 blocks) 40 24 23.5 76 (3 or 4 blocks) M3.5 Terminal Screw B: G: R: Y: black green red yellow Panel Thickness 0.8 to 7.5 5.5 23 53 (1 or 2 blocks) L H K OC 1NO R: red Y: yellow Panel Thickness 0.8 to 7.5 36 1NO-1NC M3.5 Terminal Screw 36 AVN301N o40 AVN310N 1NC 36 Pushlock Push Turn Lock AJN3 1NO Dimensions (mm) Code PUS (nameplate sold separately) Part No. o40 Mushroom Pushlock Key Reset ABN3K Contact o40 Shape Mushroom Pushlock Turn Reset AVN3 Button Color 40 24 76 (3 or 4 blocks) * Specify a button color code in place of in the Part No. * Round bezel (metal): Chrome-plated * Cylinder (metal): Chrome-plated * Other contact configurations and gold-plated silver contacts are also available. See page 19. * Pushlock Turn Reset: Button is maintained when pressed and is reset when turned clockwise. Red buttons only. Note: o30 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use XN or HN series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Pushlock Key Reset: Button is maintained when pressed and is reset with a key. Key is removable from both depressed and reset posi tions. Two keys are supplied. Note: o30 pushlock key reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use HW series emergency stop switches with a HW9Z-A30 ring adapter (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Button is locked when turned clockwise in the depressed position and is reset when turned counterclockwise. 23 o30 o30 Series Pushbuttons Pull / Push-Pull / Pin Lock Pushbuttons Package Quantity: 1 2NO ATN2320 (nameplate sold separately) Mushroom Push-Pull ATN21 (nameplate sold separately) ATN2302 1NO-1NC ATN2111 2NO ATN2120 2NC ATN2102 2NO-2NC ATN2122 1NO-1NC ATN2211 2NO-2NC ATN2222 53 (1 or 2 blocks) M3.5 Terminal Screw B: G: R: Y: black green red yellow 6 stroke 32.5 (nameplate sold separately) 40 Panel Thickness 0.8 to 7.5 23 6 stroke 53 (1 or 2 blocks) 38.5 76 (3 or 4 blocks) 6 M3.5 Terminal Screw 6 40 Panel Thickness 0.8 to 7.5 38.4 Mushroom Push-Pull Return ATN22 2NC 23 6 36 ATN2311 Panel Thickness 0.8 to 7.5 36 1NO-1NC M3.5 Terminal Screw 23 3 stroke 53 (1 or 2 blocks), 76 (3 or 4 blocks) 3 stroke 36 ATN2310 o40 1NO Dimensions (mm) Code o40 Mushroom Pull ATN23 Part No. o40 Contact 38.4 Shape Button Color 40 35.5 * Specify a button color code in place of in the Part No. * Round bezel and shroud (metal): Chrome-plated * Square bezel (metal): Chrome-plated * Other contact configurations and gold-plated silver contacts are also available. See page 19. * Pull: Pulling the button operates the contacts, and releasing the button return the contacts. Suitable to prevent unintended operation when an object touches the pushbutton. Up to 2 contact blocks (1 layer) can be mounted on pull switches. * Push-Pull: 2-position pushbutton. Pushing or pulling operates the contacts. Button is maintained in both depressed and reset positions. Note: o30 push pull switches cannot be used as emergency stop switches. When emergency stop switches are required, use XN series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push-Pull Return: 3-position pushbutton. Pushing or pulling the button operates the contacts. Button is spring-returned to the center position. Contact Operation Pull Switch Contact Push-Pull Return Switch Push-Pull Switch Contact ATN21 Push Pull Contact 1NO 1NO-1NC 1NO-1NC 1NC 2NO 2NO-2NC 1NO-1NC 2NC 2NO 2NO-2NC 2NC 24 ATN23 Normal Pull Push ATN22 Normal Pull o30 o30 Series Pushbuttons o30 Square Twin / Twin Maintained Pushbuttons Package Quantity: 1 Shape Square Twin (Momentary) UWQN1 Contact Part No. ON OFF 1NO 1NO Button Color UWQN11010 Dimensions (mm) M3.5 Terminal Screw Panel Thickness 0.8 to 13 1NO 1NC UWQN11001 42 O N ON: Black OFF: Red OFF 6 23 36 53 47 (1 or 2 blocks) 15.5 70 (3 or 4 blocks) (nameplate sold separately) Square Twin (Maintained) UWQN2 2NO 2NC UWQN12002 ON OFF 1NO - UWQN21000 1NC - UWQN20100 Panel Thickness 0.8 to 13 M3.5 Terminal Screw 1NO-1NC - UWQN21100 42 ON ON: Black OFF: Red OFF 6 23 36 53 47 (1 block) Mushroom Twin Maintained (Without buttons) ABBN33 (nameplate sold separately) - UWQN20200 Top Bottom 1NO - ABBN1110 1NC - ABBN1101 1NO-1NC - ABBN1111 2NO - ABBN1120 2NC - ABBN1102 2NO-2NC - ABBN1122 Top Bottom 1NO - ABBN3310 1NC - ABBN3301 1NO-1NC - ABBN3311 2NO - ABBN3320 2NC - ABBN3302 2NO-2NC - ABBN3322 M3.5 Terminal Screw 15.5 9 Black (B), green (G), and red (R) buttons are supplied with each unit. 50 86 2NC 70 (2 blocks) 57 80 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 40 21 50 86 (nameplate sold separately) UWQN22000 o35 Flush Twin Maintained ABBN11 - o40 (nameplate sold separately) 2NO 57 80 Panel Thickness 0.8 to 7.5 40 * Round bezel (metal): Chrome-plated * Other contact configurations and gold-plated silver contacts are also available. See page 19. * Square Twin (Momentary): Two independent momentary switches are contained in one unit, each operated by ON or OFF button. With the o30 adapter removed from the sleeve, the unit can mount in a o25.5mm mounting hole for the o25 series. * Square Twin (Maintained): The contact operates when ON button is pressed and is maintained in the depressed position. The button is reset by pressing the OFF button. * Twin Maintained: The contact operates when the top button is pressed and is maintained in the depressed position. The button is reset by pressing the bottom button. Different combinations of flush, extended HW9Z-A30 buttons, and colors are available (ABN1B-, ABN2B-). See page 65. Mushroom buttons for the ABBN33 are ordered separately. Specify the color code (ABN3B-). See page 65. 25 o30 o30 Series Pilot Lights Dome Pilot Lights Package Quantity: 1 Shape Lamp Lamp Receptacle Part No. Dome APN1 APNE1 Without Lamp BA9S LED APN199 BA9S APN1DN Lens/LED Color Code C: DNA: DNY: G: O: R: S: W: A: G: PW: R: S: W: Y: clear amber yellow green orange red blue white amber green pure white red blue white yellow A: G: R: S: W: Y: amber green red blue white yellow Operating Voltage Code Specify an operating voltage code in place of in the Part No. Input Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full Voltage 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC 16D: 110V DC Transformer DC-DC Converter * * Specify a Lens/LED Color Code in place of in the Part No. * Use a pure white (PW) LED for yellow (Y) illumination. DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC). Dimensions Full Voltage Panel Thickness 0.8 to 7.5 21.5 23.5 36 o35 M3 Terminal Screw 40 Transformer DC-DC Converter Panel Thickness 0.8 to 7.5 58.5 26 23.5 36 o35 M3.5 Terminal Screw 40 All dimensions in mm. Applicable Lamp See pages 17 for lamps. o30 o30 Series Pilot Lights o30 Square / Rectangular (Marking) Pilot Lights Package Quantity: 1 Shape Lamp Lamp Receptacle Part No. Square UPQN3B Without Lamp BA9S UPQN3B99 LED BA9S UPQN3BD Rectangular (Marking) UPQN4 Without Lamp BA9S UPQN499 LED BA9S UPQN4D Lens/LED Color Code DA: DY: C: G: O: R: S: W: A: G: R: S: W: Y: DA: DY: G: O: R: S: W: A: G: R: S: W: Y: amber yellow clear green orange red blue white amber green red blue white yellow amber yellow green orange red blue white amber green red blue white yellow Applicable Lamp See pages 18 for lamps. Operating Voltage Code Specify an operating voltage code in place of in the Part No. Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC 16D: 110V DC Input Type Full Voltage Transformer DC-DC Converter * * Specify a Lens/LED Color Code in place of in the Part No. * Use a pure white (PW) LED for yellow (Y) illumination. * On the rectangular marking pilot light, a clear lens and a color marking plate are used for white illumination. Marking plate: 24 x 30 mm, 2 mm thick DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC). 27 o30 o30 Series Pilot Lights Dimensions Rectangular Full Voltage UPQN4 Square Full Voltage UPQN3B Panel Thickness 0.8 to 5.5 29.5 20 40 44 52.2 36 34 Panel Thickness 0.8 to 4.5 66 40 44 10.5 36 52.2 M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 25 60 10.5 Rectangular Transformer Rectangular DC-DC Converter UPQN4 Square Transformer Square DC-DC Converter UPQN3B M3.5 Terminal Screw 36 52.2 34 40 40 44 34 40 20 30 36 23 Panel Thickness 0.8 to 4.5 M3 Terminal Screw 36 52.2 34 M3 Terminal Screw 40 44 All dimensions in mm. Reflector 1. The lamp housing of the square LED illuminated pilot lights has a built-in reflector. 2. Make sure that the reflector does not fall off when removing the lens or marking plate. 3. When replacing the LED lamp of UPQNE4 (rectangular), use a lamp holder tool (OR-55). 4. To remove the reflector, insert a flat screwdriver inside the groove of the reflector and lightly push out. Panel Mounting 1. Tighten the square ring to the operator and position the ring correctly. 2. Lightly tighten the screw to secure the pilot light onto the panel. Screw Groove Tighten the screw lightly so that the panel does not bend. Recommended tightening torque: 0.15 N*m 28 o30 o30 Series Illuminated Pushbuttons o30 Round Extended Illuminated Pushbuttons Package Quantity: 1 Lamp Receptacle Shape Round Extended ALN2 AOLN2 ALNE2 AOLNE2 Operation Lamp Contact 1NO-1NC Momentary ALN29920DN 2NC ALN29902DN 1NO-1NC ALN211DN 2NO ALN220DN 2NC BA9S Maintained AOLN29911DN 2NO AOLN29920DN 2NC AOLN29902DN 1NO-1NC AOLN211DN 2NO AOLN220DN 2NC AOLN202DN LED Color Code and Operating Voltage Code Lens/LED Color Code Specify a Lens/LED Color Code in place of . amber green pure white red blue white yellow 16: 126: 26: 246: 386: Use a pure white (PW) LED for yellow (Y) illumination. 46: 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC See pages 17 for lamps. Input Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC ALN202DN 1NO-1NC Without Lamp Applicable Lamp ALN29911DN 2NO Without Lamp LED A: G: PW: R: S: W: Y: Part No. Full voltage Transformer Dimensions M3.5 Terminal Screws 5.5 23 63 (2 blocks) 86 (4 blocks) 9 23.5 Panel Thickness 0.8 to 7.5 o40 o35 o24 Panel Thickness 0.8 to 7.5 40 23 97.5 (2 blocks) 120.5 (4 blocks) 9 23.5 o40 M3.5 Terminal Screw o24 M3 Terminal Screw ALN2/AOLN2 BA9S/Transformer o35 ALN2/AOLN2 BA9S/Full Voltage 40 All dimensions in mm. 29 o30 o30 Series Illuminated Pushbuttons Round Extended with Half Shroud Illuminated Pushbuttons Package Quantity: 1 Shape Lamp Receptacle Round Extended ALGN2 AOLGN2 ALGNE2 AOLGNE2 Operation Lamp Contact Part No. 1NO-1NC Momentary ALGN29911DN 2NO ALGN29920DN 2NC ALGN29902DN 1NO-1NC ALGN211DN 2NO ALGN220DN Without Lamp LED 2NC BA9S Maintained ALGN202DN 1NO-1NC AOLGN29911DN 2NO AOLGN29920DN Without Lamp 2NC AOLGN29902DN 1NO-1NC AOLGN211DN 2NO AOLGN220DN 2NC AOLGN202DN LED Applicable Lamp See pages 17 for lamps. Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code A: G: PW: R: S: W: Y: Input Operating Voltage Code Specify a Lens/LED Color Code in place of . amber green pure white red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 126: 26: 246: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC Dimensions ALFN2/AOLFN2 BA9S/Full Voltage 5.5 23 61.5 (2 blocks) 84.5 (4 blocks) 30 23 96 (2 blocks) 119 (4 blocks) o40 o35 o40 o35 40 25 Panel Thickness 0.8 to 5.5 o29.5 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 o29.5 M3 Terminal Screw ALFN2/AOLFN2 BA9S/Transformer 40 25 All dimensions in mm. o30 o30 Series Illuminated Pushbuttons o30 Round Extended with Half Shroud Illuminated Pushbuttons Package Quantity: 1 Shape Lamp Receptacle Round Extended ALFN2 AOLFN2 ALFNE2 AOLFNE2 Operation Lamp Contact 1NO-1NC Without Lamp Momentary ALFN29920DN 2NC ALFN29902DN 1NO-1NC ALFN211DN 2NO ALFN220DN 2NC BA9S Maintained AOLFN29911DN 2NO AOLFN29920DN 2NC AOLFN29902DN 1NO-1NC AOLFN211DN 2NO AOLFN220DN 2NC AOLFN202DN LED Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Specify a Lens/LED Color Code in place of . amber green pure white red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. ALFN202DN 1NO-1NC Without Lamp See pages 17 for lamps. Input Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 126: 26: 246: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC Applicable Lamp ALFN29911DN 2NO LED A: G: PW: R: S: W: Y: Part No. Dimensions ALFN2/AOLFN2 BA9S/Full Voltage 5.5 23 61.5 (2 blocks) 84.5 (4 blocks) 23 96 (2 blocks) 119 (4 blocks) o40 o35 o40 o35 40 25 Panel Thickness 0.8 to 5.5 o29.5 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 o29.5 M3 Terminal Screw ALFN2/AOLFN2 BA9S/Transformer 40 25 All dimensions in mm. 31 o30 o30 Series Illuminated Pushbuttons Mushroom (o40) Illuminated Pushbuttons Package Quantity: 1 Shape Lamp Receptacle o40 Mushroom ALN3 AOLN3 ALNE3 AOLNE3 Operation Lamp Contact Part No. 1NO-1NC Without Lamp Momentary LED ALN39911DN 2NO ALN39920DN 2NC ALN39902DN 1NO-1NC ALN311DN 2NO ALN320DN 2NC BA9S Without Lamp Maintained LED ALN302DN 1NO-1NC AOLN39911DN 2NO AOLN39920DN 2NC AOLN39902DN 1NO-1NC AOLN311DN 2NO AOLN320DN 2NC AOLN302DN Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Specify a Lens/LED Color Code in place of . A: G: R: S: W: Y: Input Operating Voltage Code amber green red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 126: 26: 246: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC Dimensions ALN3/AOLN3 BA9S/Full Voltage ALN3/AOLN3 BA9S/Transformer 5.5 23 63 (2 blocks) 86 (4 blocks) 32 23.5 M3.5 Terminal Screws Panel Thickness 0.8 to 7.5 40 23 97.5 (2 blocks) 120.5 (4 blocks) 23.5 36 36 o40 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o40 M3 Terminal Screw Applicable Lamp 40 See pages 17 for lamps. o30 o30 Series Illuminated Pushbuttons o30 Pushlock Turn Reset/Push Turn Lock Illuminated Pushbuttons Package Quantity: 1 Shape Lamp Receptacle Operation Lamp o40 Mushroom Pushlock Turn Reset AVLN3 AVLNE3 Without Lamp Pushlock Turn Reset BA9S LED o40 Mushroom Push Turn Lock AJLN3 Without Lamp BA9S Contact 1NO-1NC AVLN39911DNR 2NO AVLN39920DNR 2NC AVLN39902DNR 1NO-1NC AVLN311DNR 2NO AVLN320DNR 2NC AVLN302DNR 1NO-1NC AJLN39911DN 2NO AJLN39920DN 2NC AJLN39902DN 1NO-1NC AJLN311DN 2NO AJLN320DN 2NC AJLN302DN Push Turn Lock LED Part No. Applicable Lamp See pages 17 for lamps. Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Operating Voltage Code Specify a Lens/LED Color Code in place of . A: G: R: W: Y: amber green red white yellow Input 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 126: 26: 246: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC * Pushlock Turn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only. Note: AVNL3 and AVNLE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use XN or HN series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Lens is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise. Dimensions AVLN3 BA9S/Full Voltage AVLN3 BA9S/Transformer M3.5 Terminal Screws Panel Thickness 0.8 to 7.5 23 23 23.5 97.5 (2 blocks) 120.5 (4 blocks) 23.5 AJLN3 BA9S/Transformer M3.5 Terminal Screws Panel Thickness 0.8 to 7.5 23 23 63 (2 blocks) 86 (4 blocks) 23.5 97.5 (2 blocks) 120.5 (4 blocks) K 5.5 H C LO o40 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 36 AJLN3 BA9S/Full Voltage PUS 63 (2 blocks) 86 (4 blocks) o40 5.5 o40 o40 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 40 23.5 All dimensions in mm. 33 o30 o30 Series Selector Switches ASN Selector Switches (Knob Operator) Package Quantity: 1 ASN 4 3 1 Contact Block Contact Configuration 1NO 1NO-1NC 90 2-position 2NO 2NO-2NC 1EM-1LB 1NO 1NO-1NC 2NO 2NO-2NC 1EM-1LB Mounting Contact Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 NO -- NO NC NO NO NO NC NO NC EM LB NO -- NO NC NO NO NO NC NO NC EM LB Contact Block Contact Configuration 1NO-1NC 2NO-2NC 45 3-position 2NO-2NC 2NC 4NC 1NO-1NC 2NO-2NC 2NO-2NC 2NC 4NC Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 * Knob: Black * Round bezel (metal): Chrome-plated * Units marked with differ in shape. See page 40 for dimensions. * When a terminal cover is required, order an applicable terminal cover referring to page 59. * Nameplates are ordered separately. 2 NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC Operator Position Maintained L L R Spring Return from Right R L Maintained L R L R R ASN310 ASN410 ASN311 ASN411 ASN320 ASN420 ASN322 ASN422 ASN37S (Note) ASN47S (Note) -- -- ASN3010 ASN4010 ASN3011 ASN4011 ASN3020 ASN4020 ASN3022 ASN4022 ASN307S (Note) ASN407S (Note) Operator Position Maintained C L C R L R Spring Return from Left L C ASN111 ASN211 ASN122 ASN222 ASN15S ASN25S ASN17S ASN27S ASN18S ASN28S R Maintained C L R Spring Return from Right L C R ASN1011 ASN2011 ASN1022 ASN2022 ASN105S ASN205S ASN107S ASN207S ASN108S ASN208S Note: The overlapping time is shorter for left to right than right to left. Take overlapping time into consideration. 34 Spring Return from Left o30 o30 Series Selector Switches o30 ASN-T Selector Switches (Knob Operator) [Twin Rod Type] Package Quantity: 1 4 ASN-T 3 * Knob: Black * Round bezel (metal): Chrome-plated * When a terminal cover is required, order an applicable terminal cover referring to page 31. * Nameplates are ordered separately. 2 1 Contact Block 45 3-position Contact Configuration 2NO 4NO 2NO 4NO Mounting Contact Position 1 2 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NO NO NO NO Operator Position Maintained C L C R L R Spring Return from Left L C ASN120-T ASN220-T ASN140-T ASN240-T R Maintained C L R Spring Return from Right L C R ASN2020-T ASN2040-T ASN-T are twin-rod units. 35 o30 o30 Series Selector Switches ASNL Selector Switches (Lever Operator) Package Quantity: 1 4 ASNL 3 * Lever: Black * Round bezel (metal): Chrome-plated * Units marked with differ in shape. See page 40 for dimensions. * When a terminal cover is required, order an applicable terminal cover referring to page 59. * Nameplates are ordered separately. 2 1 Contact Block Contact Configuration 1NO 1NO-1NC 90 2-position 2NO 2NO-2NC 1EM-1LB 1NO 1NO-1NC 2NO 2NO-2NC 1EM-1LB Mounting Contact Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 NO -- NO NC NO NO NO NC NO NC EM LB NO -- NO NC NO NO NO NC NO NC EM LB Contact Block Contact Configuration 1NO-1NC 2NO-2NC 45 3-position 2NO-2NC 2NC 4NC 1NO-1NC 2NO-2NC 2NO-2NC 2NC 4NC Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC Operator Position L Maintained L R R Spring Return from Right R L ASN3L10 ASN4L10 ASN3L11 ASN4L11 ASN3L20 ASN4L20 ASN3L22 ASN4L22 ASN3L7S (Note) ASN4L7S (Note) -- Maintained L R L R -- ASN30L10 ASN40L10 ASN30L11 ASN40L11 ASN30L20 ASN40L20 ASN30L22 ASN40L22 ASN30L7S (Note) ASN40L7S (Note) Operator Position Maintained C L C R L R Spring Return from Left L C ASN1L11 ASN2L11 ASN1L22 ASN2L22 ASN1L5S ASN2L5S ASN1L7S ASN2L7S ASN1L8S ASN2L8S R Maintained C L R Spring Return from Right L C R ASN10L11 ASN20L11 ASN10L22 ASN20L22 ASN10L5S ASN20L5S ASN10L7S ASN20L7S ASN10L8S ASN20L8S Note: The overlapping time is shorter for left to right than right to left. Take overlapping time into consideration. 36 Spring Return from Left o30 o30 Series Selector Switches o30 ASNL-T Selector Switches (Lever Operator) [Twin Rod Type] Package Quantity: 1 4 2 ASNL-T 3 * Lever: Black * Round bezel (metal): Chrome-plated * When a terminal cover is required, order an applicable terminal cover referring to page 59. * Nameplates are ordered separately. 1 Contact Block 45 3-position Contact Configuration 2NO 4NO 2NO 4NO Mounting Contact Position 1 2 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NO NO NO NO Operator Position Maintained C L C R L R Spring Return from Left L C ASN1L20-T ASN2L20-T ASN1L40-T ASN2L40-T R Maintained C L R Spring Return from Right L C R ASN20L20-T ASN20L40-T ASN-T are twin-rod units. 37 o30 o30 Series Selector Switches ASNK Key Selector Switches Package Quantity: 1 ASNK 4 * Cylinder: Chrome-plated * Round bezel (metal): Chrome-plated * On spring-returned types, the keys can be released only from the maintained position. On maintained types, the key can be released from every position. Key retained positions are also available. See page 20. * Key selector switch is supplied with two standard keys. Two different keys are available upon request. * When a terminal cover is required, order an applicable terminal cover referring to page 59. * Nameplates are ordered separately. 2 3 1 Contact Block Contact Configuration 1NO 1NO-1NC 90 2-position 2NO 2NO-2NC 1EM-1LB 1NO 1NO-1NC 2NO 2NO-2NC 1EM-1LB Mounting Contact Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 NO -- NO NC NO NO NO NC NO NC EM LB NO -- NO NC NO NO NO NC NO NC EM LB Contact Block Contact Configuration 1NO-1NC 2NO-2NC 45 3-position 1NO-1NC 1EM-1LB 1EM-1LB 2EM-2LB 1NO-1NC 2NO-2NC 1NO-1NC 1EM-1LB 1EM-1LB 2EM-2LB Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NC NO NC NO NC NO NC EM LB EM LB EM LB EM LB NO NC NO NC NO NC NO NC EM LB EM LB EM LB EM LB Operator Position L Maintained L R R Spring Return from Right L R ASN3K10 ASN4K10 ASN3K11 ASN4K11 ASN3K20 ASN4K20 ASN3K22 ASN4K22 ASN3K7S (Note) ASN4K7S (Note) -- Maintained L R R L -- ASN30K10 ASN40K10 ASN30K11 ASN40K11 ASN30K20 ASN40K20 ASN30K22 ASN40K22 ASN30K7S (Note) ASN40K7S (Note) Operator Position Maintained C L C R L R Spring Return from Left L C ASN1K11 ASN2K11 ASN1K22 ASN2K22 ASN1K5S ASN2K5S ASN1K7S ASN2K7S ASN1K8S ASN2K8S R Maintained C L R Spring Return from Right L C ASN10K11 ASN20K11 ASN10K22 ASN20K22 ASN10K5S ASN20K5S ASN10K7S ASN20K7S ASN10K8S ASN20K8S Note: The overlapping time is shorter for left to right than right to left. Take overlapping time into consideration. 38 Spring Return from Left R o30 o30 Series Selector Switches o30 ASNK-T Key Selector Switches [Twin Rod Type] Package Quantity: 1 * Cylinder: Chrome-plated * Round bezel (metal): Chrome-plated * On spring-returned types, the keys can be released only from the maintained position. On maintained types, the key can be released from every position. Key retained positions are also available. See page 20. * Key selector switch is supplied with two standard keys. Two different keys are available upon request. * When a terminal cover is required, order an applicable terminal cover referring to page 59. * Nameplates are ordered separately. ASNK-T 4 2 3 1 Contact Block Contact Configuration 1NO 1NO-1NC 90 2-position 2NO 2NO-2NC 1EM-1LB 1NO 1NO-1NC 2NO 2NO-2NC 1EM-1LB Mounting Contact Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 NO -- NO NC NO NO NO NC NO NC EM LB NO -- NO NC NO NO NO NC NO NC EM LB Contact Block Contact Configuration 2NO 4NO 45 3-position 2NO-2NC 2NC 4NC 2NO 4NO 2NO-2NC 2NC 4NC Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC Operator Position L L R -- Maintained R Spring Return from Right L R ASN3K10-T ASN4K10-T ASN3K11-T ASN4K11-T ASN3K20-T ASN4K20-T ASN3K22-T ASN4K22-T ASN3K7S-T ASN4K7S-T Maintained L R Spring Return from Left L R ASN40K10-T -- ASN40K11-T ASN40K20-T ASN40K22-T ASN40K7S-T Operator Position Maintained C L C R L R Spring Return from Left L C ASN1K20-T ASN2K20-T ASN1K40-T ASN2K40-T ASN1K5S-T ASN2K5S-T ASN1K7S-T ASN2K7S-T ASN1K8S-T ASN2K8S-T R Maintained C L R Spring Return from Right L C R ASN20K20-T ASN20K40-T ASN20K5S-T ASN20K7S-T ASN20K8S-T ASN-T are twin-rod units. 39 o30 o30 Series Selector Switches Dimensions Knob Operator Dimensions of knob operator marked with or "-T" in the Part No. 45 6 23 54 (1 or 2 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 45 45 6 40 23 58 (1 or 2 blocks) 22 77 (3 or 4 blocks) 36 36 o35 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 90 40 22 81 (3 or 4 blocks) Lever Operator Dimensions of lever operator marked with or "-T" in the Part No. Panel Thickness 0.8 to 7.5 45 45 23 58 (1 or 2 blocks) 27 25.0 6 40 36 36 o35 23 54 (1 or 2 blocks) 25.0 6 M3.5 Terminal Screw 45 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 90 40 26.5 81 (3 or 4 blocks) 77 (3 or 4 blocks) Key Selector Dimensions of key selector switches marked with "-T" in the Part No. M3.5 Terminal Screw 23 6 54 (1 or 2 blocks) 40 22 Panel Thickness 0.8 to 7.5 45 45 23 57 (1 or 2 blocks) 22 80 (3 or 4 blocks) 77 (3 or 4 blocks) 40 o35 45 36 24.5 6 90 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 16.5 40 38 All dimensions in mm. Contact Block Mounting Position and Contact Configuration Chart 4 Left Center Right 2 L 3 40 1 1 2 3 4 NO NO NC NC C R Operator position o30 o30 Series Selector Switches o30 ASTN Selector Switches (Knob Operator) 90 2-position No. of Positions Package Quantity: 1 ASTN * Knob operator: Black * Round bezel (metal): Chrome-plated Contact Configuration Contact Block Mounting Position Contact 1 2 1 2 3 4 NO NC NO NO NC NC 1NO-1NC 2NO-2NC Contact Configuration Contact Block NO NO NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC 2NO-2NC 2NO 4NO 1NO-1NC 2NO-2NC 1NO-1NC ASTN3222 ASTN4222 Maintained C L R R -- Spring Return from Left L -- -- -- -- -- -- Spring Return from Right Spring Return Two-way R L ASTN4211 C 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 4NO R Spring Return from Right ASTN3211 Operator Position L 2NO-2NC L R Contact 2NO-2NC 45 3-position L Mounting Position 2NO Maintained Operator Position C C L R -- L R C -- ASTN5120 R ASTN1122 ASTN2122 ASTN20122 ASTN5122 ASTN1222 ASTN2222 ASTN20222 ASTN5222 ASTN1340 -- -- -- ASTN1422 -- ASTN20422 -- ASTN1520 -- ASTN20520 -- ASTN1540 -- ASTN20540 -- ASTN1611 -- -- -- ASTN1622 -- -- -- -- -- -- ASTN5111 Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. Center Left 2 L 3 1 1 2 3 4 NO NO NC NC C Right R Operator Position M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 90 45 45 6 36 4 Dimensions o35 Contact Block Mounting Position and Contact Configuration Chart 23 58 (2 blocks) 81 (4 blocks) 40 27 41 o30 o30 Series Selector Switches ASTNL Selector Switches (Lever Operator) 90 2-position No. of Positions Package Quantity: 1 ASTNL Contact Configuration * Lever operator: Black * Round bezel (metal): Chrome-plated Contact Block Mounting Contact Position 1 2 1 2 3 4 1NO-1NC 2NO-2NC Contact Configuration Contact Block Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 2NO 2NO-2NC 2NO-2NC 45 3-position NO NC NO NO NC NC 4NO 2NO-2NC 2NO 4NO 1NO-1NC 2NO-2NC 1NO-1NC NO NO NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC Maintained Operator Position L L R R Spring Return from Right ASTN42L11 ASTN32L22 ASTN42L22 Maintained Spring Return from Left C L C R L R L -- -- -- -- -- Spring Return from Right Spring Return Two-way R L ASTN32L11 Operator Position -- C L R C -- -- ASTN11L22 ASTN21L22 ASTN201L22 ASTN51L22 ASTN12L22 ASTN22L22 ASTN202L22 ASTN52L22 ASTN13L40 -- ASTN14L22 -- ASTN204L22 -- ASTN15L20 -- ASTN205L20 -- ASTN15L40 -- ASTN205L40 -- ASTN16L11 -- -- -- ASTN16L22 -- -- -- -- -- -- ASTN51L11 -- C L R ASTN51L20 -- -- Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. Contact Block Mounting Position and Contact Configuration Chart Center Left 42 1 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 90 45 45 1 2 3 4 NO NO NC NC R Operator Position 6 23 58 (1 or 2 blocks) 81 (4 blocks) 29 36 C o35 2 L 3 Right 25.0 4 Dimensions 40 R o30 o30 Series Selector Switches o30 ASTNK Key Selector Switches 90 2-position No. of Positions Package Quantity: 1 ASTNK Contact Configuration * Cylinder: Chrome-plated * Round bezel (metal): Chrome-plated * On the spring-returned, the keys can be released only from the maintained position. * On the maintained, the key can be released from every position. Key retained positions are also available. See page 20. Contact Block Mounting Contact Position 1 2 1 2 3 4 1NO-1NC 2NO-2NC Contact Configuration Contact Block Mounting Contact Position 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 2NO 2NO-2NC 2NO-2NC 45 3-position NO NC NO NO NC NC 4NO 2NO-2NC 2NO 4NO 1NO-1NC 2NO-2NC 1NO-1NC NO NO NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC L L R Spring Return from Right Maintained Operator Position ASTN32K11 ASTN42K11 ASTN32K22 ASTN42K22 Spring Return from Left Maintained Operator Position C L C L R L R -- -- -- -- -- Spring Return from Right Spring Return Two-way R L R -- C C L R L R -- -- ASTN11K22 ASTN21K22 ASTN201K22 ASTN51K22 ASTN12K22 ASTN22K22 ASTN202K22 ASTN52K22 ASTN13K40 -- ASTN14K22 -- ASTN204K22 -- ASTN15K20 -- ASTN205K20 -- ASTN15K40 -- ASTN205K40 -- ASTN16K11 -- -- -- ASTN16K22 -- -- -- -- -- -- ASTN51K11 -- C R ASTN51K20 -- -- Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. Center Left 1 Panel Thickness 0.8 to 7.5 2 L 3 Right M3.5 Terminal Screw 1 2 3 4 NO NO NC NC C R Operator Position 45 45 o35 4 Dimensions 6 40 Contact Block Mounting Position and Contact Configuration Chart 23 57 (1 or 2 blocks) 80 (4 blocks) 16.5 40 38 43 o30 o30 Series Illuminated Selector Switches ASLN Illuminated Selector Switches 90 2-position ASLN (Base BA9S) Contact Configuration Package Quantity: 1 Contact Block Mounting Position Contact 1 NO 2 NC 1 NO 2 NO 1 2 3 4 NO NC NO NC L Spring Return from Right Maintained Operator Position Lamp L L R Spring Return from Left L R R R Without Lamp ASLN29911N ASLN219911N ASLN229911N LED ASLN211DN ASLN2111DN ASLN2211DN Without Lamp ASLN29920N ASLN219920N ASLN229920N LED ASLN220DN ASLN2120DN ASLN2220DN Without Lamp ASLN29922N ASLN219922N ASLN229922N LED ASLN222DN ASLN2122DN ASLN2222DN 1NO-1NC 2NO 2NO-2NC Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Operating Voltage Code A: G: R: S: W: Y: amber green red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. Input 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 136: 26: 256: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] Dimensions Contact Block Mounting Position and Contact Configuration Chart M3.5 Terminal Screws M3 Terminal Screw 3 44 1 R 5.5 40 23 63 (2 blocks) 9 A: 86 (4 blocks) Operator Position o40 L NO NC NO NC 45 o35 2 1 2 3 4 90 45 Right o25 4 Left Panel Thickness 0.8 to 7.5 (including nameplate) B: 97.5 (2 blocks), 120.5 (4 blocks) 28 A: Full voltage B: Transformer o30 o30 Series Illuminated Selector Switches o30 ASLN Illuminated Selector Switches 45 3-position Package Quantity: 1 Contact Contact Block ConfiguMounting Conration Maintained Operator Position Position tact L 1 NO 2 NO 1 NC 2 NC 1 2 3 4 1 2 3 4 1 2 3 4 NO NO NC NC NO NO NO NO NC NC NC NC C Lamp C L R Without Lamp Spring Return from Right L R C Spring Return from left R L C Spring Return Two-way L R C R ASLN39920N ASLN319920N ASLN329920N ASLN339920N ASLN320DN ASLN3120DN ASLN3220DN ASLN3320DN Without Lamp ASLN39902N ASLN319902N ASLN329902N ASLN339902N LED ASLN302DN ASLN3102DN ASLN3202DN ASLN3302DN Without Lamp ASLN39922N ASLN319922N ASLN329922N ASLN339922N LED ASLN322DN ASLN3122DN ASLN3222DN ASLN3322DN Without Lamp ASLN39940N ASLN319940N ASLN329940N ASLN339940N LED ASLN340DN ASLN3140DN ASLN3240DN ASLN3340DN Without Lamp ASLN39904N ASLN319904N ASLN329904N ASLN339904N LED ASLN304DN ASLN3104DN ASLN3204DN ASLN3304DN 2NO LED 2NC Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Operating Voltage Code A: G: R: S: W: Y: amber green red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. Input 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 136: 26: 256: 386: 46: Transformer 100/110V AC 120V AC 200/220V AC 240V AC 380V AC 400/440V AC Contact Block Mounting Position and Contact Configuration Chart 4 Dimensions Center Left 1 M3.5 Terminal Screws M3 Terminal Screw Panel Thickness 0.8 to 7.5 (including nameplate) 90 45 45 2 L 3 Right 1 2 3 4 NO NO NC NC C R Operator Position 5.5 o40 4NC o35 4NO o25 2NO-2NC 40 23 63 (2 blocks) 9 A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) 28 A: Full Voltage B: Transformer 45 o30 o30 Series Selector Pushbuttons ABN Ring Operator / ABNL Lever Operator Selector Pushbuttons Package Quantity: 1 Ring/Lever Contact Circuit CofiguraCode tion Shape Ring Operator Contact Block Pushbutton A 1NO-1NC I G 2NO Ring Operator (90 2-position) Panel Thickness 0.8 to 7.5 (including nameplate) 25 41 B 40 o28 o35 M3.5 Terminal Screw 6 23 D 40 Panel Thickness 0.8 to 7.5 (including nameplate) M3.5 Terminal Screw 23 6 23 25 41 40 o28 o35 C 40 ABNL I 2NO-2NC D Lever Operator (90 2-position) 26 41 40 o35 50 6 23 40 40 o35 26 41 50 23 F Panel Thickness 0.8 to 7.5 (including nameplate) M3.5 Terminal Screw 6 23 E Panel Thickness 0.8 to 7.5 (including nameplate) M3.5 Terminal Screw 40 H 1 NO 2 NC 1 NC 2 NO 1 NO 2 NC 1 NO 2 NO 3 NO 4 NO 1 NC NC 3 NO 4 NO 1 NC 2 NC 3 NO 4 NO 1 NC NO 1 NC 2 NC 3 NO 4 NO 1 NC Part No. ABN6111 ABN6L111 ABN6411 ABN6L411 ABN9111 ABN9L111 ABN7120 ABN6122 ABN6L122 ABN6222 ABN6L222 ABN6422 ABN6L422 ABN7122 ABN7L122 ABN7222 ABN7L222 ABN7322 ABN7L322 ABN9122 ABN9L122 2 4 NC NC Blocked Part No. Push NC NO Normal 1 3 Push 2 2 Button Color Code Mounting ConNormal Position tact ABN Lever Operator B: G: R: Y: black green red yellow 2 NC 3 NO 4 NO 1 NC 2 NC 3 NO 4 NO Blocked * Specify a button color code in place of in the Part No. * Ring/Lever (metal): Chrome-plated Notes 1. Circuit Codes A, B, C, and I: When the ring or lever operator is turned, the button is pushed in. 2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button. 3. Circuit Codes G and H: The pushbutton does not operate when the ring or lever operator is turned to the left position. 4. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure may be caused. Contact Block Mounting Position 80 2 50 4 Mounting Hole Layout 3 1 50 Ring Operator 80 Lever Operator 46 o30 o30 ARN/ARNS Series Mono-lever Switches Single lever offers up to four directions of control Mono-lever switches operate in four directions using a single lever. Switch contacts are actuated in the direction in which the lever is pushed, enabling quick and accurate control in any desired direction. Ideal for machine tools and industrial machines. The lever action can be maintained or springreturned in any combination. Also available with interlock mechanism to prevent inadvertent actuation. Applicable Standards Mark File No. or Organization UL 508 UL Listing File No. E68961 CSA C22.2 No.14 CSA File No. LR21451 GB14048.5 CCC No.2013010305661112 Specifications and Ratings Contact Ratings Contact Block Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 BR 600V 10A AC-15 (A600) DC-13 (P600) Characteristics Contact Ratings by Utilization Category Operational Voltage AC-12 AC Operational 50/60 Hz AC-15 Current DC-12 DC DC-13 Control of resistive loads and solid state loads Control of electromagnetic loads (> 72 VA) Control of resistive loads and solid state loads Control of electromagnets 24V 10A 10A 10A 4A 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Specifications Contact Configuration Operating Temperature Storage Temperature Operating Humidity Insulation Resistance Dielectric Strength Mechanical Life Electrical Life Lever Knob Weight (approx.) Double-break slow action Each contact block contains two independent contacts (2NO, 1NO-1NC, 2NC) Up to four contact blocks can be mounted -25 to +50C (no freezing) -35 to +80C (no freezing) 45 to 85% RH (no condensation) 100 M minimum (500V DC megger) Between live and dead parts: 2,500V AC, 1 minute 500,000 operations minimum (Interlocking: 250,000 operations minimum) Black 276g (ARN4-1111-20202020) BR Contact Block Control Mechanism The contact block is made of nylon resin. Each contact block contains two pairs of double-break silver contacts. There are three types as shown in the diagram below and up to four contact blocks can be mounted in any direction. A wide variety of circuits allows diverse combinations of control. When the operator lever is pushed to about 30 in each direction from the neutral position, the contact in that direction activates. The lever can operate in two, three, or four directions, and combinations of maintained or springreturn from any position are possible. 47 o30 ARN/ARNS Series Mono-lever Switches Mono-lever Switches ARN2-1010-B M3.5 Terminal Screw Panel Thickness 0.8 to 6 Spring return ARN2-0202-B Maintained 4-position (Up-Down-LeftRight) 6 Maintained 23 83 ARN4-1111-B Minimum horizontal/vertical mounting centers: 110 ARNS2-1010-B M3.5 Terminal Screw Panel Thickness 0.8 to 6 Maintained o42 Spring return ARNS2-2020-B ARNS2-0101-B 30 2-position (Left-Right) 51 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 Spring return ARN4-2222-B 2-position (Up-Down) 51 o22 ARN2-0101-B 30 Maintained o42 Spring return ARN2-2020-B 2-position (Left-Right) ARNS (Short Lever) Dimensions (mm) 30 Maintained 2-position (Up-Down) Part No. 51 Lever Action 30 Position o22 Operator ARN (Long Lever) Spring return ARNS2-0202-B 6 23 63 Spring return ARNS4-2222-B Maintained 2-position (Up-Down) Minimum horizontal/vertical mounting centers: 70 ARNL2-1010-B M3.5 Terminal Screw Panel Thickness 0.8 to 6 4-position (Up-Down-LeftRight) ARNL2-0101-B 30 Maintained 0 o22 3 Spring return ARNL2-2020-B 2-position (Left-Right) The operator lever is locked only in the center position. 51 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 o42 ARNL (Interlocking) ARNS4-1111-B 51 Maintained 4-position (Up-Down-LeftRight) Spring return ARNL2-0202-B 6 23 Maintained 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 83 ARNL4-1111-B 51 Minimum horizontal/vertical mounting centers: 110 Spring return ARNL4-2222-B Specify Contact Configuration from the table below in place of . Terminal covers are ordered separately. Panel Cut-Out o3 0.5 +0 0 .5 33 +0.5 0 Right R0.8 max. 4.8 +0.2 0 0 Up Mono-Lever with Terminal Cover 68 31 Lever Operator Position 31 68 Left Down Ordering Information Contact Blocks Model ARN ARNS ARNL 1: 2: 3: 4: 1 block 2 blocks 3 blocks 4 blocks Lever Action Right Down Left Contact Arrangement Order of Entry: UpRight DownLeft Order of Entry: UpRight DownLeft 1: Maintained 2: Spring return 0: Blocked 10: 01: 11: 20: 02: 00: 1NO 1NC 1NO-1NC 2NO 2NC Blocked Lever Knob Color 1 2 B: black * To calculate the number of contact blocks required, add the number of NO and NC contacts on each pair of adjoining positions (up + right, right + down, down + left, and left + up). The largest of the four sums is the number of contact blocks required. Up to four contact blocks can be mounted. 48 3 4 1 3 5 7 9 11 13 15 1 NO - - - NO - - - Lever Operation Mode 1: Maintained 2: Spring return 0: Blocked 0 1 2 - - - - NC - - - NO - - NO - - - - NC - - - NC - - NC Terminal No. Up No. of Terminal No. 4 - 1012 - 2 0 0 0 0 2 1 1 B Contact Block Position [Example] 64 Direction of Lever Operation When ordering, specify items to according to the following example. ARN 23 2 4 6 8 10 12 14 16 Contact Block Type BR-2E BR-1E BR-2E BR-3E : Contacts marked with do not operate. * Specify the same number of contacts for the contact blocks of opposing corner (up-down, right-left), except for the blocked direction. * When UL and CSA markings are required on the mono-lever switch, specify as shown below. [Example] ARN4-1012-20000211B- U o30 ARN/ARNS Series Accessories and Replacement Parts o30 Accessories and Maintenance Parts Shape Specification Part No. Ordering No. Package Quantity Description 70 70 o3 0 Nameplate .5 MLO 1 Chrome-plated brass (matte surface) MLO MLOPN10 10 ARN-VL2 ARN-VL2 1 Terminal covers are ordered separately. When ordering, specify the Part No. and the required quantity. Order 2 pieces for each contact block. BR-1E BR-1E 1 2NO contact BR-2E BR-2E 1 1NO-1NC contact BR-3E BR-3E 1 2NC contact Bellows ARN-BL ARN-BL 1 For ARN/ARNS (Locking ring not included) Bellows (Interlocking) ARNL-BL ARNL-BL 1 For ARNL (Locking ring not included) 1 Specify a color code in place of . B (black), G (green), R (red) For ARN/ARNS Terminal Cover Contact Block (BR) Knob ARNB- ARNB- 49 o30/o25 CS Series Cam Switches 71 standard circuits to choose from * Wide variety of heavy-duty oiltight cam switches * Operators available up to 12 positions * Contact blocks rated at 600V, 10A * Ideal for ammeter/voltmeter applications * UL listed and CSA approved Applicable Standards Mark File No. or Organization CCC No.2012010305525956 (ACSNO, ACSNK) No.2013010305604910 (ACSSO, ACSSK) No.2013010305600565 (UCSQO, UCSQM) GB14048.5 (except ACSSO and ACSSK) Specifications and Ratings Contact Ratings Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 600V 10A AC-15 (A600) DC-13 (P600) Characteristics Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V -- -- 8A 5A 110V 10A 5A 3A 1.2A Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Specifications Contact Configuration Operation Angle Operator Positions Operating Temperature Storage Temperature Operating Humidity Insulation Resistance Dielectric Strength Mechanical Life Electrical Life Degree of Protection Weight (approx.) Double-break slow action contacts Two contacts in one deck Up to 6 decks available (Spring-return: Up to 3 decks) Maintained Spring return 30, 45, 60, 90 45 2 to 12 2, 3, 4 -20 to +50C (no freezing) -40 to +80C (no freezing) 45 to +85% RH (no condensation) 100 M (500V DC megger) 2500V AC, 1 minute (between live and dead parts) 1 to 3 decks: 500,000 operations 4 to 6 decks: 200,000 operations 200,000 operations minimum ACSNO, ACSSO: IP65 (IEC 60529) ACSNK, ACSSK: IP54 (IEC 60529) UCS: IP40 (IEC 60529) 319g (ACSNO-663-S2B) CSB Contact Block The CSB contact block contains two poles of double-break contacts. The contacts are operated by a cam designed to perform a required contact operation. Up to six contact blocks can be mounted on a maintained-action operator base, and up to three contact blocks on a spring return operator base. 50 M3.5 Screw Terminal 220V 6A 3A 1A 0.45A 440V 2A 1A 0.4A 0.2A o30 CS Series Cam Switches o30/o25 Cam Switches Model o30 Series o25 Series ACSNO ACSSO Contact Block Decks Maintained: 1 to 6 decks Spring return: 1 to 3 decks Positions Maintained: 2 to 12 positions Spring return: 2 to 4 positions Spring Angle Handle Return Maintained: 30, 45, 60, 90 Spring return: 45 only Contact NameArrangement Spring return from right Spring return from left Spring return two-way Y2, S2, P2, F2, 25S2 (25S2 is for ACSSO only) (one speci fied handle supplied) Two standard keys are supplied. See page When the H2 55 to 57. key handle is required, specify H2. (Photo: ACSNO with Y2 handle) ACSNK ACSSK 58 H2 Handle Key (black) Maintained: 1 to 6 decks Spring return: 1 to 3 decks Maintained: 2 to 8 positions Spring return: 2 to 4 positions Maintained: 45, 90 Spring return: 45 only Spring return from right Spring return from left Spring return two-way Maintained: 1 to 6 decks Spring return: 1 to 3 decks Maintained: 2 to 12 positions Spring return: 2 to 4 positions Maintained: 30, 45, 60, 90 Spring return: 45 only Spring return from right Spring return from left Spring return two-way 24 plate See page 61. (ordered sepa rately) Standard Key (2 keys supplied) UCSQO (Enclosed) Y2, S2, F2, P2 (one speci fied handle supplied) (Photo: With Y2 handle) UCSQM (Enclosed) Indicator Left: Green Right: Red Left Type CQ See page 60. Spring return: 1 to 3 decks Right Spring return: 3 positions Spring return: 45 only C1007 C1008 C1009 C1010 C1018 C2006 C2007 C2021 See page 55 to 57. Spring return two-way Spring Return 2-way Type CQM See page 60. For handles and accessories, see page 52 and 53. Dimensions 2 12N+9 12N+9 33 +0.5 0 35 o25.5 +0.5 0 (ACSSO/ACSSK) 47 * Spring Return: 44 Maintained: 42 N: Number of Contact Blocks * Spring Return: 44 Maintained: 42 N: Number of Contact Blocks o5 9 12 47 47 30.7 30 52 9 12 R0.8 max. +0.2 4.8 0 Panel Thickness 0.8 to 6 M3.5 Terminal Screw 52 50 (S2 Handle) 52 2 47 Panel Cut-out ACSNK/ACSSK Panel Thickness 0.8 to 6 M3.5 Terminal Screw 52 ACSNO/ACSSO o30.5 +0.5 0 (ACSNO/ACSNK) * Minimum horizontal/vertical mounting centers With P2 handle: 125 With other handles: 70 UCSQO Panel Cut-out UCSQM Panel Thickness 7.0 max. 46.4 4-M4 Screw 4-o4.5 Panel Thickness 7.0 max. 4-M4 Screw 46.4 3 12N+9 7 All dimensions in mm. 48 25 Spring Return: 31 Maintained: 29 N: Number of Contact Blocks 70 M3.5 Terminal Screw 2 48 64 52 9 12 50 (P2 Handle) 2 M3.5 Terminal Screw 64 52 41 (Y2 Handle) o1 9 12 12N+9 31 7 N: Number of Contact Blocks 43 48 48 70 * Minimum horizontal/vertical mounting centers With P2 handle: 125 With other handles: 70 51 o30/o25 CS Series Cam Switches Ordering Information When ordering, specify items through as the designation example below. Contact Block Decks Model ACSNO ACSNK ACSSO ACSSK UCSQO UCSQM Positions Decks 1 deck 2 decks 3 decks 4 decks 5 decks 6 decks Angle Code 1 2 3 4 5 6 Spring return: 1 to 3 decks only Spring Return Handle Positions Code Angle Code 3 30 2 2 positions 4 45 3 3 positions 6 60 4 4 positions 9 90 5 5 positions 6 6 positions 7 7 positions 8 8 positions 9 9 positions 10 10 positions 11 11 positions 12 12 positions Spring return: ACSNK/ 2 to 4 positions only ACSSK: 45 and 90 only Spring return: 45 only Key irremovable position Circuit No. For ACSNK/ ACSSK, specify the code(s) of irremovable position(s) in numerical order. For standard contact configurations, use designation code on pages 55 to 57. For custom contact configurations, use the Custom Contact Configuration Specification Sheet on page 58. Return Code Spring return RO (Code) from left Y2, S2, P2, Spring return OR F2, H2, 25S2 from right (Color) Spring return RR B: Black two-way See table below. Spring return code 25S2 is for is required only for ACSSO only. spring return. Standard ACSNK/ ACSSK: no specification required Handle Designation Code Designation Example o30 S Handle Shape UCSQO - 2 3 4 RR - S2B - C2006 ACSNO - 2 3 4 RR - Y2B - MAU-C2006-ZT2 Code Applicable Cam Switch Color o25, o30 Y Handle 22 30 19 Y2 ACSNO ACSSO UCSQO UCSQM 20 1. When a special contact configuration is required, specify the contact configuration using the Custom Contact Configuration Specification Sheet on page 58. 2. A specified handle is attached. 3. Accessories such as nameplates and jumpers are sepa rately ordered. 4. The key of the key operated cam switch is removable at every position unless otherwise specified. The key is irremovable at return position. The return and irremovable positions must be specified in Part No. Positions at 180 from irremovable positions are also irremovable. Example: 4-positions, spring return from right, irremovable at positions 3 and 4 ACSNK-344OR-134-C3012 o25, o30 S Handle 20 30 30 S2 20 o25, o25 S Handle 20 25.6 30 25S2 ACSSO 20 B: black o25, o30 P Handle 30 50 P2 ACSNO ACSSO UCSQO UCSQM 40 o25, o30 F Handle o50 30 F2 40 Key Handle 18 40 ACSNK ACSSK H2 24 Spring Return Operation Available combinations of operator positions, angles, and return directions are listed in the table below. Positions 2-position From Left From Right 2 Return Direction 1 From Left 1 2 3 1 2 3 4-position From Left From Right Two-way 2 2 1 3-position From Right 1 3 1 2 3 2 4 24RO 24OR 34RO 34OR 34RR Applicable Cam Switches ACSNO, ACSSO, ACSNK, ACSSK, UCSQO Contact Block Decks 1 to 3 decks Note: Maintained do not require spring return code . Codes 52 44RO 3 4 3-position Two-way 2 1 3 1 44OR 34RR UCSQM o30 CS Series Accessories and Replacement Parts o30/o25 Accessories and Replacement Parts Shape Material Part No. Ordering No. Package Quantity Remarks Jumper CJ-1 CJ-1PN10 10 For connecting terminals of adjoining contact blocks CJ-2 CJ-2PN10 10 For connecting terminals of the same contact block Metal (copper) CJ-1 CJ-2 Rubber Boot Nitril rubber Terminal Cover Supplied with 2 selftapping screws for mounting CR-1 CR-1 1 For preventing ingress of dust into the contact blocks Not applicable for the UCSQO and UCSQM CS-VL2-13S CS-VL2-13S 1 For 1 to 3 decks of contact blocks CS-VL2-46S CS-VL2-46S 1 For 4 to 6 decks of contact blocks Plastic (PPE) o30 S Handle CS-VL2-13S CS-VL2-46S Shape o25, o30 Y Handle Material (Color) Part No. Ordering No. Package Quantity 22 30 19 20 o25, o30 S Handle 20 30 30 Polybutylene terephthalate (Black) CSH-YB CSH-YB 1 Polybutylene terephthalate (Black) CSH-SB CSH-SB 1 Phenol resin (Black) CSH-25SB CSH-25SB 1 Phenol resin (Black) CSH-PB CSH-PB 1 Bakelite (Black) CSH-FB CSH-FB 1 Phenol resin (Black) CSH-H2B CSH-H2B 1 Metal (brass nickel-plated) CSH-K301 CSH-K301PN02 2 Polyamide CS-HF2C CS-HF2CPN05 5 For Y, o30 S, and o25 S handles M3 x 12 CS-SCW-M3-12 CS-SCW-M3-12PN10 10 For P and F handles M3 x 25 CS-SCW-M3-25 CS-SCW-M3-25PN10 10 20 o25 S Handle 20 25.6 30 20 o25, o30 P Handle 30 50 40 o25, o30 F Handle 30 o50 40 Key Handle 18 40 24 Spare Keys Handle Shaft Handle Screw Handle Screw 53 o30/o25 CS Series Instructions Instructions Installing the Terminal Cover for the CS series Cam Switches Minimum Mounting Centers for Installing the Terminal Cover 70 mm min. (P2 handle: 125 mm) * Complete wiring before installing the terminal cover on the bottom plate of the contact block. * The terminal cover has six holes. Of the four round holes at four corners, use two diagonal pair of holes to install the terminal cover. Either pair can be used. * Insert the attached self-tapping screws into the pair of holes and tighten the screws to a torque of 0.8 to 1.0 N*m. * For 1 through 3 decks of contact blocks, use terminal cover CS-VL2-13S. * For 4 through 6 decks of contact blocks, use terminal cover CS-VL2-46S. * The CS-VL2-46S consists of the CS-VL2-13S and a terminal cover for the fourth through sixth decks. Combine the two parts together as shown. Note that once combined, the two parts cannot be separated. 100 mm min. (P2 handle: 125 mm) * Although the minimum mounting centers are 100 mm horizontally and 70 mm vertically, determine the mounting centers in consideration of convenience of wiring. For the P2 handle, the minimum mounting centers are 125 mm horizontally and vertically. Mounting Hole Bottom Plate Self-tapping Screw (attached) Insert the screws into a diagonal pair of holes. CS-VL2-13S Mounting Hole CS-VL2-13S For 4 through 6 decks of contact blocks (CS-VL2-46S) 52 64.6 (CS-VL2-13S) 66.1 (CS-VL2-46S) 33 (CS-VL2-13S) 34.5 (CS-VL2-46S) Terminal Cover Dimensions 9 47 91.4 (CS-VL2-13S) 94.4 (CS-VL2-46S) 2 7.5 12 12N+9 40.5 (N: Number of Contact Blocks) All dimensions in mm. 54 o30 CS Series Instructions o30/o25 Standard Contact Configurations Listing Order of the Table The 76 standard contact configurations are listed in the order of the circuit number. Same Circuits Shown in the following examples, circuits of Fig. 1 and Fig. 2 have the same functions. When ordering, examine the standard contact configurations. Your requirements may be satisfied simply by changing external wiring of the stan dard contact configurations. * The following table lists 76 standard contact configurations for easy designation of required cam switch operation. * When other contact configurations are required, specify the number of contact block decks, operator positions, angles, and contact operation using the Custom Contact Configuration Specification Sheet on page 58. No. of Decks: 2 Position: 3-position Angle: 45 Fig. 1 2 3 4 RR 1 C2006 7 5 3 1 8 6 4 2 7 5 3 1 Spring Return: 2-way Circuit No. Example 1 Fig. 2 2 Fig. 1 8 6 4 2 7 5 3 1 3 1 2 Example 2 Fig. 2 8 6 4 2 7 5 3 1 3 1 2 3 8 6 4 2 7 5 3 1 4 1 2 3 4 Terminal Numbers * The terminal numbers on the contact blocks correspond with the numbers shown in the chart as shown below. 8 6 4 2 Terminal No. 1 2 3 Operator Position The arrow shows the spring return direction. Symbol Contact Operation Terminal No. 7 5 3 1 Contacts closed. 8 6 4 2 1 Contacts remain closed between two operator positions. Overlapping Contacts Contacts of different decks are both closed at one point while the handle is turned to the next position. Residual Contacts When the handle is returned to the center, the con tacts remain closed. The contacts are opened when the handle is turned to the opposite direction. Operator Position 2 Terminal No. Standard Contact Configuration Chart 1 2 9C1001 1 2 9C1002 1 2 4 OR C1003 1 2 4 OR C1004 1 3 4C1005 3 4 3 4 3 4 3 4 3 1 2 1 2 1 2 1 2 1 1 2 1 1 3 4C1006 12 2 1 3 4 RR C1007 2 1 1 3 4 RR C1008 1 3 4 RR C1009 4 3 4 3 4 3 4 3 2 1 2 1 2 1 2 1 3 1 4 4C1011 12 3 12 3 12 3 1 2 9C1013 1 2 9C1014 1 2 4 OR C1015 4 3 4 3 4 3 4 3 2 1 2 1 2 1 2 1 3 4 1 2 4C1017 1 2 1 1 3 4 RR C1018 4 3 4 3 1 2 1 2 1 2 2 9C2001 2 1 2 3 2 1 2 2 9C2002 12 4 4 12 3 2 2 1 2 6C1019 3 1 2 4 1 3 4C1016 1 2 3 12 3 3 1 2 1 3 4 RR C1010 1 2 2 1 3 1 4 2 2 3 4C2003 2 3 4C2004 2 3 4C2005 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 1 2 1 2 3 1 2 3 2 1 2 3 55 o30/o25 CS Series Instructions 2 3 4 RR C2006 2 3 4 RR C2007 2 4 4C2008 7 8 7 8 7 8 5 6 5 6 5 6 3 4 3 4 3 4 1 2 1 2 1 2 1 12 3 12 3 2 2 9C2014 2 2 9C2015 7 8 5 6 3 4 1 2 1 2 7 8 5 6 3 4 1 2 2 2 3 4C2020 8 7 8 5 6 5 6 3 4 3 4 1 2 1 1 2 3 2 3 4C2017 8 7 8 5 6 5 6 3 4 3 4 1 2 1 2 2 3 1 2 3 4 RR C2021 2 3 2 4 4C2022 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 1 2 1 3 2 3 2 1 12 3 2 5 3C2027 3 3 4C3002 2 3 4 2 3 6C2028 7 8 7 8 5 6 5 6 3 4 3 4 1 2 1 2 1 3 2 9C3001 2 3 4 2 1 2 3 4 (O) (R) (S) (T) 4 7 2 1 2 4 9C2011 7 4 2 3 4C2016 1 2 3 4C2019 3 2 4 4C2009 1 5 3 5 4C3003 2 2 3 6C2029 7 8 5 6 3 4 2 1 1 2 3 (R) (S) (T) 3 3 6 4C3004 3 3 4C3005 11 12 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 1 2 3 4 9C3008 11 12 9 10 7 8 5 6 3 4 3 1 3 4 9C3009 2 1 2 1 2 3 4 (O) (RS) (ST) (TR) 3 4 1 5 3 2 9C3010 2 3 4 5 2 6 1 3 3 4C3011 2 3 3 4 4C3012 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 1 3 6 3C3013 2 2 3 4 1 3 3 6C3014 1 2 3 6 6C3015 2 2 3 1 3 5 3C3016 2 3 4 3 4 4C3017 11 12 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 3 4 5 1 6 2 3 1 3 3 6C3018 2 4 5 6 1 4 4 4C4001 2 3 4 4 8 4C4002 15 16 15 16 14 13 14 12 9 10 11 12 11 12 7 8 9 10 9 10 5 6 7 8 7 8 3 4 5 6 5 6 1 2 3 4 3 4 1 2 1 2 3 1 4 2 4C4004 4 2 9C4005 2 3 4 4 2 9C4006 15 16 15 16 15 16 13 14 13 14 13 14 11 12 11 12 11 12 9 10 9 10 9 10 7 8 7 8 7 8 5 6 5 6 5 6 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 2 1 2 1 2 3 4 5 6 7 8 4 4 9C4007 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 1 2 3 4 (O) (R) (S) (T) 2 3 4 4 4 9C4003 11 2 2 1 5 13 1 56 3 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 1 2 3 4 (O) (R) (S) (T) 4 3 4C4008 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 1 2 3 o30 CS Series Instructions o30/o25 4 5 4C4009 5 3 4C5001 6 4 4C6001 6 12 3C6002 23 24 23 24 19 20 21 22 21 22 15 16 17 18 19 20 19 20 13 14 15 16 17 18 17 18 11 12 13 14 15 16 15 16 9 10 11 12 13 14 13 14 7 8 9 10 11 12 11 12 5 6 7 8 9 10 9 10 3 4 5 6 7 8 7 8 1 2 3 4 5 6 5 6 1 2 3 4 3 4 1 2 1 1 2 3 4 5 1 2 3 1 6 4 9C6003 23 24 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 2 3 2 1 4 6 9 3C6004 2 3 4 5 6 7 8 6 6 6C6005 9 10 11 12 6 6 4C6006 23 24 23 24 23 24 21 22 21 22 21 22 19 20 19 20 19 20 17 18 17 18 17 18 15 16 15 16 15 16 13 14 13 14 13 14 11 12 11 12 11 12 9 10 9 10 9 10 7 8 7 8 7 8 5 6 5 6 5 6 3 4 3 4 3 4 1 2 1 2 (O) (R) (S) (T) 1 2 3 4 4 3 2 1 0 1 2 3 1 4 2 3 4 5 1 2 (RS) (ST) (RT) (RE) (SE) (TE) 1 2 3 4 5 6 6 Application Examples (Voltmeter and Ammeter Circuits) 1 2 6 C1019 (ammeter switching, 1CT circuit) 2 3 6 C2029 (ammeter switching, 2CT circuit) CS CS CT 2 4 9 C2011 (ammeter switching, 2CT circuit) 3 4 1 2 A CT 7 8 5 6 3 4 1 2 CS A R S T R S T A O R S T R S T CT 7 8 5 6 3 4 1 2 E E 2 4 4 C2022 (voltmeter switching, 3PT circuit) PT 3o-4W V 11 12 9 10 V R S T E 11 12 9 10 8 5 6 7 8 7 8 3 4 5 6 5 6 1 2 3 4 3 4 1 2 1 2 PT O R S T PT 3o-4W 4 4 9 C4003 (ammeter switching, 3CT circuit) CS CT CS O RS ST TR R S T 7 6 4 9 C6003 (ammeter switching, 3CT circuit) R S T 3 4 9 C3009 (voltmeter switching, 3PT circuit) CS CS R S T E E 3 4 9 C3008 (voltmeter switching, 2PT circuit) 4 4 9 C4007 (ammeter switching, 2CT circuit) CS CS A R S T O R S T A R S T O R S T 23 24 15 16 15 16 21 22 13 14 13 14 19 20 11 12 11 12 17 18 9 10 9 10 15 16 7 8 7 8 13 14 5 6 5 6 11 12 3 4 3 4 9 10 1 2 1 2 7 8 5 6 3 4 1 2 CT E V CT A E E 57 o30/o25 CS Series Instructions Custom Contact Configurations Specification Sheet * The preceding pages provide 68 standard contact configurations. When other contact configurations are required, specify the number of contact block decks, operator positions, angles, and contact operation using the Custom Contact Configuration Specification Sheet shown below. * For available number of contact blocks and operator positions, see the Ordering Information on page 52. 1. Specify operator positions Indicate the operator positions starting at the first position. When spring return operation is required, mark an arrow between two operator positions to indicate the spring return direction. 2. Specify contact operation at each operator position Indicate the required operation of all contacts at each operator position using the following symbols. Symbol Contacts closed. Contacts remain closed between two operator positions. Overlapping Contacts Contacts of different decks are both closed at one point while the handle is turned to the next position. Overlapping contacts are not available for handle angles of 30 and 45. Residual Contacts When the handle is returned to the center, the contacts remain closed. The contacts are opened when the handle is turned to the opposite direction. 7 Deck 2 5 * One deck of contact block contains two poles of contacts and four terminals. When the handle is made to turn 180 or more, special attention is needed. Since one cam operates the two poles of contacts on opposite positions, the same contact operation repeats on the other pole of contacts when the handle is turned 180. When different contact operation is needed for handle angles of 180 or more, use another deck of contact block. 3 Deck 1 1 Angle Positions Spring Return 1 2 3 4 Contact Operation 5 CS Series Cam Switch Custom Contact Configuration Specification Sheet Part No.: Quantity: Model Deck Decks Positions Terminal No. Angle Spring Return Handle Contact Configuration Chart Terminal No. 23 24 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 Deck 6 Deck 5 Deck 4 Deck 3 Deck 2 Deck 1 Angle Positions Spring Return 58 1 2 3 4 5 6 7 8 9 10 11 12 o30 o30 Series Accessories and Replacement Parts o30 Terminal Covers Terminal Cover o30 Series Switches & Pilot Lights N-VL2 N-VL3 N-VL4 APN-PVL APD-PVL 38.4H x 22W 38H x 30.4W 38.4H x 24W 38H x 46W 37H x 44W Pilot Light APN, APNE, UPQN, UPQNE Use of termi nal covers increases the depth by the dimensions below. X Terminal Cover +5.0 mm Full Voltage Pilot Light APD, APDE Pilot Light APN, APNE, APD, APDE, UPQN, UPQNE X Transformer DC-DC Converter X +5.2 mm +2.7 mm 1 contact block Terminal Cover CB Pushbutton ABN, ABD, AON, AOD, AVN, ABGD, AJN, ABFD, ATN, AOFD, UBQN, AVD, UOQN, AJD, UWQN, AZD, ABBN, AYD, ABBS (o25) Selector Switch ASN, ASD, ASTN Selector Pushbutton ABN, ASBD X 2 contact blocks CB CB X 2 pieces +0 mm 3 contact blocks CB CB CB X 2 pieces 4 contact blocks CB CB CB CB X 2 pieces Illuminated Pushbutton ALN, ALD, ALNE, ALDE, AOLN, AOLD, AOLNE, Full Voltage AOLDE, ALGN, ALGD, ALGNE, ALGDE, AOLGN, AOLGDE, ALFN, ALFD, ALFNE, ALFDE, AOLFN, AOLFD, AOLFNE, AOLFDE, AVLN, AVLD, AVLNE, AVLDE, AJLN, AJLD, AJLNE, AJLDE, ULQN, UOLQN Illuminated Selector Switch ASLN, ASLD Transformer DC-DC Converter X 2 pieces +4.5 mm X +1.5 mm Push-to-Check Pilot Light APN1P Ordering Terminal Covers * When ordering terminal covers, specify the Part No. and the quantity. Terminal Cover (N-VL2) Terminal Cover (N-VL2) 59 o30 o30 Series Accessories and Replacement Parts Nameplates Material With Legend 1 NA-0PN10 10 Applicable Unit 24.5 40 1 0.5 o3 NA- NA-PN10 10 NALO 1 NALOPN10 10 40 NALO 0. o3 Aluminium 1.2 mm thick Black o30 switches & pilot lights .5 NA- 47.5 30 Blank NA-0 Dimensions (mm) 5 R1 NALO Package Quantity NA-0 Aluminium 1.2 mm thick White letters on black background NA Ordering No. R1 7 Blank Part No. 5 Legend 7. Model 70 4 Blank Blank MLO MLO MLOPN10 With Legend (Legend Codes 31 and 53 only) CQ-0PN10 10 CQ- o43 Letters should not be engraved within this line * With adhesive tapes on the back 2-o3.5 1 o13 CQ-PN10 10 CQM-0 1 CQM-0PN10 10 20 64 * With adhesive tapes on the back CQM-0 12 5 CQM- 1 2-o3.5 o13 CQM- * Specify a legend code in place of in the Ordering No. 60 1 ARN/ARNS Mono-Lever UCSQO Cam Switch Aluminium 0.5 mm thick White letters on black background With Legend (Legend Code 31 only) CQ-0 CQ- Blank CQM 10 5 0. o3 CQ-0 Aluminium 0.5 mm thick White letters on black background CQ 1 29.3 MLO Brass (chrome-plated) 1.0 mm thick Matte CQM-PN10 10 40 64 UCSQM Cam Switch o30 o30 Series Accessories and Replacement Parts o30 Nameplates Model Legend Material Blank Part No. Ordering No. Package Quantity CQN-0 1 CQN-0PN10 10 Dimensions (mm) Applicable Unit * With adhesive tapes on the back CQN-0 CQN With Legend (Legend Codes 31, 35, and 53 only) Aluminium 0.5 mm thick White letters on black background .5 o30 1 CQN- CQN- Blank ACSNO, ACSNK Cam Switches o30 mm Selector Switches 64 CQN-PN10 10 CQS-0 1 CQS-0PN10 10 CQS- 1 CQS-PN10 10 * With adhesive tapes on the back CQS-0 5.5 With Legend (Legend Code 53 only) o2 CQS Aluminium 0.5 mm thick White letters on black background ACSSO, ACSSK Cam Switches o25 mm Selector Switches CQS- 64 * Specify a legend code in place of in the Ordering No. Legends Code 0 1 2 3 4 31 35 53 Legend (blank) ON OFF START STOP OFF-ON HAND-AUTO HAND-OFF-AUTO Shape and Engraving Area 36 2 10 2 5 36 2 18.5 18.5 2 Standard Large Type NA Type NALO Example Shape Standard Large Engraving Area Height Width Max. No. of Lines 5 10 36 36 1 2 No. of Letters on 1 Line 14 14 The above example is when the letter is 4 mm tall. 61 o30 o30 Series Accessories and Replacement Parts Accessories Shape Material Part No. Ordering No. Package Quantity Locking Ring Wrench Dimensions (mm) OR-12 OR-12 1 6 o2 29 o 90 o25 Series Lamp Holder Tool 4 o3 o46 o45 o37 Nitril rubber o3 0 o2 2 * Used to tighten the locking ring when installing the o30 or o25 switch onto a panel. o30 Series Nitril rubber OR-55 OR-55 o11.6 * Used to install and remove the LED lamps. See page 67. 1 14 OR-55 59 Contact Rubber Boot For momentary 1 layer of contact blocks (2 contact blocks) 18 OC-99 OC-99 42 1 52 Nitril rubber (black) * Rubber boot used to prevent oil and dirt from entering into the contact block. * Temperature range: -5 to +60C * Cannot be used for zinc diecast switches & pilot lights. 44 Silicone rubber For 2 layers (translucent) of contact blocks (4 contact blocks) OC-90 OC-90 1 OC-290 OC-290 1 * Applicable to AVN3 and AJN3. * Applicable to o30 diecast zinc pushbuttons and selector switches. 38.8 Contact Rubber Boot For 1 layer of contact blocks (2 contact blocks) Anti-rotation Ring 42.8 42.4 (65.4) * Used to prevent the operator from turning. Generally used when using no nameplates on selector switches and selector pushbuttons. Metal (diecast) (zinc-plated) 2.8 OGL-11 OGL-11PN10 0.8 10 .5 o30 o3 9 Nitril rubber (black) OB-13B OB-13BPN05 5 o40 5 * Used to plug unused o30mm mounting holes. * Gray also available. Ordering No.: OB-13PN05 10 Rubber Mounting Hole Plug 5 o30 o34 Plastic Mounting Hole Plug OBP-11 OBP-11 5 o36 1 24 Gasket M30 P1.5 Screw 4 Plastic (gray) Plug: ABS Gasket: Chloroprene rubber * Used to plug un o30mm mounti * Gray also availa Ordering Type N OB-13PN05 * Tightening torque: 1.2 N* m. * Degree of protection: IP65 Locking Ring Metal (diecast) (zinc-plated) OB-11 OB-11 1 o36 5 * Tightening torque: 1.2 N* m. * Degree of protection: IP65 Gasket P1.5 Screw 4 M30 24 Metallic Mounting Hole Plug Locking Ring 62 o30 o30 Series Accessories and Replacement Parts o30 Accessories Nitril rubber Button Clear Boot Part No. Package Quantity - - Black OC-11B OC-11B Green OC-11R OC-11R Red OC-11G OC-11G Yellow OC-11Y OC-11Y 1 For flush pushbuttons For extended pushbuttons OC-121 OC-121 1 OC-122 OC-122 1 EPDM rubber Dust-proof Rubber Cover for Jumbo Mushrooms Dimensions (mm) * Metallic bezels covered with a rubber boot to enhance waterproof characteristics. * Button is not included. Applicable to extended pushbuttons only. o28 o38 M30P1.5 * Used to cover and protect pushbuttons where units are subject to water splash. Not suitable for outdoor use or where the units are subject to oil splash. A 37 37 OC-121 OC-122 A B 16 16 * Used for ABN4G pushbuttons. Nitril rubber (black) OC-4GN OC-4GN 19 Color Ordering No. B Button Cover for Extended Pushbuttons Part No. 11 Material Panel Thickness 1.2 to 5.5 1 o80 Shape 32 Padlock Cover * Used to protect pushbuttons, illuminated push buttons, and selector switches (knob operator). 82.5 Panel Thickness 0.8 to 3.2 OL-KL1 1 70 30 OL-KL1 93 6.5 R6 Polyarylate (gasket: nitryl rubber) 24 o3 0 0. o5 2 Key Hole o8 29.5 Waterproof Rubber Gasket 0.5t 30 Metal Protector * Used to protect flush pushbuttons from inadvertent operation. * Can be easily attached using the locking ring. 42.5 OL-C OL-C 1 Locking Attachmentt 16 Mounting Centers 50 min. 25 5 Metal (zinc-plated brass) .5 o30 11.5 1.6 30 * Used to lock an extended pushbutton in the depressed position. * Can be easily attached using the locking ring. OL-H 1 Locking Plate o6 hole 9.5 OL-H 16.5 Metal (zinc-plated brass) Mounting Plate 63 o30 o30 Series Accessories and Replacement Parts Maintenance Parts Shape Specification Part No. Ordering No. Package Quantity Remarks 2 * Cannot be used with pin lock, selector pushbuttons, and monolever units. Specify a color code in place of . B (black), G (green), R (red), W (white), Y (yellow) * Cannot be used with pin lock, selector pushbuttons, and monolever units. Metallic Bezel Metal (zinc diecast: chromeplated) OG-11 OG-11PN02 Plastic Bezel Polycarbonate OGP-11 OGP-11PN02 2 OGP-13 OGP-13PN02 2 OGP-14 OGP-14PN02 2 OGP-1411 OGP-1411 1 Metal (zinc diecast) OL-11 OL-11PN05 5 Polycarbonate (clear) ABN1B-C ABN1B-CPN05 5 Polyacetal TN-0 TN-0PN10 10 Clear Plastic Bezel for Flush Pushbuttons Clear Plastic Bezel for Extended Pushbuttons Acrylic (clear) * Clear plastic bezel and full shroud. * OGP-1411 cannot be used with LED illumination units and diecast units. Clear Plastic Bezel for Illuminated Pushbuttons Metal Bezel for Illuminated Pushbuttons Clear Button Cover Marking Plate 64 * Used on flush and extended pushbuttons to indicate a mark or a symbol engraved on the marking plate. The clear button cover holds the marking plate. The o30 series marking chip can only be used on the ABN1 and AON1. * Specify a color code in place of . B (black), G (green), R (red), W (white), Y (yellow) o30 o30 Series Accessories and Replacement Parts o30 Maintenance Parts Shape Description Contact Block (BS: Dark gray) Material BS010E BS010E-MAU BS010E-MAU BS001E BS001E BS001E-MAU BS001E-MAU EM contact (early make) BS010SE BS010SE LB contact (late break) BS001SE NC contact BS010SE-MAU BS010SE-MAU 1 * Push rod color: Green * -MAU has gold contacts 1 * Push rod color: Red * -MAU has gold contacts 1 * Push rod color: Black * -MAU has gold contacts 1 * Push rod color: White * -MAU has gold contacts 1 * Push rod color: Green 1 * Push rod color: Red BST010 BST010-MAU BST001 BST001 BST001-MAU BST001-MAU EM contact (early make) BST010S BST010S 1 * Push rod color: Black LB contact (late break) BST001S BST001S 1 * Push rod color: White APN106LN- APN106LN-PN05 5 A (amber), C (clear), G (green), R (red), S (blue), W (white), Y (yellow) * Use the white (W) lens for pure white (PW) illumination UPQN406L- UPQN406L-PN05 APN(E)1 Used for UPQNE4 U(O)LQNB AS resin 5 UPQN406LD- UPQN406LD-PN05 Used for ULQN06L- ULQN06L-PN05 UPQN06LD- UPQN06LD-PN05 ALN2L- * -MAU has gold contacts Applicable Units: * Pushlock Turn Reset * Push Turn Lock * LED Illuminated Pushbutton * LED Illuminated Selector Switch C (clear), G (green), R (red), S (blue) * Use the clear (C) lens for white illumination. A (amber), Y (yellow) * Use the amber (A) lens for orange illumination. C (clear), G (green), R (red), S (blue) 5 A (amber), W (white), Y (yellow) * Use the amber (A) lens for orange illumination. ALN2L-PN05 5 C (clear), G (green), R (red), S (blue) ALN2LD- ALN2LD-PN05 5 A (amber), W (white), Y (yellow) * Use the white (W) lens for pure white (PW) illumination Flush ABN1B- ABN1B-PN05 5 Extended ABN2B- ABN2B-PN05 5 ABN3B- ABN3B-PN02 2 ABN1BN- ABN1BN-PN05 5 UPQN3B U(O)LQN Lens Color BST010 Used for Package Quantity BST010-MAU NO contact BS001SE BS001SE-MAU BS001SE-MAU NC contact Lens Ordering No. BS010E NO contact Contact Block (BST: Light gray) Part No. Used for ALN, AOLN (LED) AS resin Button Mushroom Button Flush Button Polyacetal Extended ABN2BN- ABN2BN-PN05 5 Mushroom ABN3BN- ABN3BN-PN02 2 ABN4B- 1 ABN4GB- 1 UBQN1B- UBQN1B-PN02 2 UBQN2B- UBQN2B-PN02 2 Mushroom (ABN4) Mushroom (ABN4G/ ABN4F) Square Flush (UBQN1) Square Extended (UBQN2) ABN4B- Ureaformaldehyde resin ABN4GB- G (green), R (red), Y (yellow) Above colors are used for o30 switches & pilot lights (dark colored operator units). For black, use black buttons from light colored operator units. B (black), G (green), R (red), S (blue), Y (yellow), W (white) Above colors are used for o30 diecast zinc switches & pilot lights (light colored operator units). B (black), G (green), R (red), Y (yellow) Polyacetal Note: Specify a button color code or Lens/LED Color Code in place of or in the Ordering No. 65 o30 o30 Series Accessories and Replacement Parts Maintenance Parts Shape Button Lens Lens Lens Description Material Part No. Ordering No. Package Quantity Remarks For o40 pushlock turn reset pushbuttons (for AVN3) AS resin AVN3B- AVN3B- 1 R (red), Y (yellow) For o40 pushlock turn reset pushbuttons (for AVLN3, AVLNE3) AS resin AVLN3L-R AVLN3L-RPN02 2 Red only For o40 pushlock turn reset pushbuttons (for AJN3) AS resin AJN3B- AJN3B- 1 B (black), G (green), R (red), Y (yellow) For o40 pushlock turn reset pushbuttons (for AJLN3) AS resin AJLN3L- AJLN3L- 1 -G (green), -R (red), L-Y (yellow), L-A (amber), L-W (white) For UPQN4 Acrylic UPQN406N-W UPQN406N-WPN05 5 OW-12 OW-12PN10 10 OW-11 OW-11PN10 10 Half shroud ABN2G ABN2G 1 Full shroud ABN2F ABN2F 1 ABN3G ABN3G 1 ABN4G ABN4G 1 ABN4F ABN4F 1 ALN2GL ALN2GL 1 * For LED illuminated pushbuttons (BA9S base) ALN2FL ALN2FL 1 * For LED illuminated push buttons (BA9S base) ASLNH ASLNH-* Marking Plate Rubber Washer (3.0mm thick) Synthetic soft vinyl Rubber Washer (1.5mm thick) Shroud (for pushbuttons) (for pushbuttons) Full shroud (for mushroom pushbuttons) Shallow shroud (for jumbo mush rooms) Deep shroud Metal (zinc diecast) (for jumbo mush rooms) Half shroud (for illuminated pushbuttons) Full shroud (for illuminated pushbuttons) Selector Knob Knob for Illuminated selector switch 66 AS resin G (green), R (red), S (blue) 1 ASLNHD ASLNHD-* A (amber), W (white), Y (yellow) o30 o30 Series Accessories and Replacement Parts o30 Maintenance Parts Shape Spare Key Description ASN3K/4K,ABN5 ASNK Spare Key Transformer ASNK-T ASNK Material Metal (nickel plated brass) 100/110V AC (for LED lamps) Part No. Package Quantity Ordering No. ASN-T1SK-24401 ASN-T1SK-24401PN02 2 ASN-SK-24401 ASN-SK-24401PN02 TW-SK-0 TW-SK-0PN02 2 TWR-016N TWR-016N 1 Remarks * Applicable to ABN3K, ABN4K, ABN5 Mounting screws are not included. 200/220V AC (for LED lamps) Pin/Chain For ABN8P pinloock Metal TWR-026N TWR-026N 1 ABN8P-PIN ABN8P-PIN 1 Pin, chain, and plate for ABN8P LED Lamps Dimensions Operating Voltage 6V AC/DC 10% Base BA9S/13 20.8 12V AC/DC 10% 24V AC/DC 10% Current Draw AC DC 7 mA (A, R, W) 8 mA 5.5 mA (G, PW, S) 11 mA 10 mA Part No. Ordering No. LSTD-6 LSTD-6 LSTD-6PN10 LSTD-1 LSTD-1 LSTD-1PN10 11 mA 10 mA LSTD-2 LSTD-2 LSTD-2PN10 Illumination Color Code A: amber G: green PW: pure white R: red S: blue W: white Use a pure white (PW) LED lamp for yellow (Y) illumination. Package Quantity Base 1 10 1 BA9S/13 10 1 10 67 o30 o30 Series Accessories and Replacement Parts Transformer DIN Rail Mount For 6V Primary Voltage Secondary Voltage Part No. 100/110V AC 200/220V AC For 24V LED TWR516 TWR526 5.5V 400/440V AC TWR546 100/110V AC TWR512 200/220V AC Applicable Load 23V TWR522 400/440V AC One full voltage pilot light or illuminated switch containing LSTD-6 One full voltage pilot light or illuminated switch containing LSTD-2) TWR542 Dimensions Shock Resistance Dielectric Strength Terminal Screw Applicable Wire Weight (approx.) 100 M minimum (500V DC megger) -30 to +60C (no freezing) -40 to +80C (no freezing) 35 to 85% RH (no condensation) Damage Limits: 30 Hz, amplitude 1.5 mm Operating extremes: 5 to 55 Hz, amplitude 0.5 mm Damage limits, Operating Extremes: 1,000 m/s2 2,500V AC, 1 minute M3.5 2 mm2 maximum, 2 wires maximum 87g 22 30 2 JAPAN PRI. Secondary Side Primary Side 1 600V M3.5 Terminal Screw 40 48 2-o3.3 Mounting Hole 52 Terminal Cover 40 41 45.5 Vibration Resistance TWR56 TWR52 100/110V AC, 200/220V AC, 400/440V AC (50/60Hz) 2.4 VA 3 Part No. Operating Voltage Current Draw Rated Insulation Voltage Insulation Resistance Operating Temperature Storage Temperature Operating Humidity SEC. 4 Specifications BAA1000 Accessories DIN Rail Part No. BAA1000 BAP1000 Ordering No. BAA1000PN10 BAP1000PN10 Length 1000 mm 1000 mm Weight (approx.) 200g 320g Material Aluminum Steel Package Quantity 10 10 End Clip BNL6 Ordering No. BNL6PN10 Applicable DIN Rail BAA1000 BAP1000 Weight (approx.) Material Package Quantity 15g Steel (Zinc-plated) 10 Dimensions (24) Part No. 45 68 9 o30 o30 Series Instructions o30 Safety Precautions * Turn off the power to the o30 series switches & pilot lights before starting installation, removal, wiring, maintenance, and inspection of the products. Failure to turn power off may cause electrical shocks or fire hazard. * To avoid a burn on your hand, use the lamp holder tool when replacing lamps. * For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a tightening torque of 1.0 to 1.3 N*m. Failure to tighten terminal screws may cause overheat and fire. Instructions Panel Mounting for Square Pushbuttons and Pilot Lights 1. Tighten the square ring to the operator and position the ring correctly. 2. Lightly tighten the screw to secure the pilot light onto the panel. Recommended tightening torque: 0.15 N*m Panel Thickness and Rubber Washer Adjust the thickness of the rubber washers according to the panel thickness. Also, make sure to include the nameplate thickness when using a nameplate. Applicable Models Applicable Models * Extended Illuminated Pushbuttons with Half Shroud (LED) * Extended Pushbuttons with Half Shroud (Diecast) * Extended Illuminated Pushbuttons with Half Shroud (Diecast) * Extended Pushbuttons with Half Shroud Panel Rubber Washer Thickness 1.5mm 3.0mm (mm) Supplied 1 piece 1 piece 0.8 1 piece 1 piece 0.8 to 2.3 - 1 piece 2.3 to 4.0 1 piece - Panel Thickness (mm) Tightening Torque for Terminal Screws Tighten the terminal screws to a torque of 1.0 to 1.3 N*m. Supplied 0.8 to 1.8 1.8 to 3.5 Rubber Washer 1.5mm 3.0mm 1 piece 1 piece - 1 piece 1 piece - Applicable Models Replacement of Lamps Lamps can be replaced by using the lamp holder tool (OR55) from the front of the panel. How to Remove To remove, slip the lamp holder tool onto the lamp head lightly. Then push slightly, and turn the lamp holder tool counterclockwise. How to Install To install, insert the lamp head into the lamp holder tool. Place the pins on the lamp base to the grooves in the lamp socket. Inset the lamp and turn it clockwise. * Extended Illuminated Pushbuttons with Full Shroud (LED) * Extended Illuminated Pushbuttons with Full Shroud (Diecast) * Mushroom Pushbuttons with Full Shroud Panel Thickness (mm) Supplied 0.8 to 2.0 2.0 to 3.5 3.5 to 5.0 5.0 to 6.0 (6.5) Rubber Washer 1.5mm 3.0mm 2 pieces 1 piece 1 piece 1 piece 1 piece 1 piece - 1 piece 1 piece - The number in brackets is for mush room pushbuttons with full shroud. Applicable Models * Toggle Lever * Knob Push Turn Lock Illuminated Pushbuttons OR-55 Installing the Anti-rotation Ring Anti-rotation rings are used on selector switches or pushbuttons which rotate and used when using no nameplates. Insert a 1.5mm thick rubber washer between the panel and the anti-rotation ring as shown on the right. Panel OGL11 Panel Thickness Rubber Washer (mm) 1.5mm 3.0mm Supplied 1 piece 1 piece 0.8 to 2.0 1 piece 1 piece 2.0 to 3.5 - 1 piece 3.5 to 5.5 (5.0) 1 piece - The number in brackets is for knob push turn lock illuminated pushbut tons. Applicable Models * Extended Pushbuttons with Full Shroud Panel Rubber Washer Thickness 1.5mm 3.0mm (mm) Supplied 0.8 to 1.5 1.5 to 3.0 3.0 to 4.5 4.5 to 6.0 6.0 to 7.5 3 pieces 3 pieces 2 pieces 1 piece - 1 piece 1 piece 1 piece 1 piece 1 piece 1 piece - Applicable Models * Extended Pushbuttons with Full Shroud (Diecast) Panel Rubber Washer Thickness 1.5mm 3.0mm (mm) Supplied 0.8 to 2.5 2.5 to 4.0 4.0 to 5.5 5.5 to 6.0 2 pieces 2 pieces 1 pieces - 1 piece 1 piece 1 piece 1 piece 1 piece - Applicable Models * Other Models (Excluding Square) Panel Rubber Washer Thickness 1.5mm 3.0mm (mm) Supplied 2 pieces 1 piece 0.8 to 3.5 2 pieces 1 piece 3.5 to 5.0 1 piece 1 piece 5.0 to 6.5 - 1 piece 6.5 to 7.5 1 piece - Rubber Washer 69 o30 o30 Series Instructions Installation of LED Illuminated Units 1. Note the polarity for wiring when connecting to DC-DC converter unit. 2. Transformer units are recommended for use in areas subjected to noise. 3. Notes for Pure White LED Lamps * Do not use the pure white LED outdoors, otherwise it will lead to the degradation of brightness and color. Do not remove or apply shock to the cap on the pure white LED lamp, otherwise it may break or damage the cap. * For the pure white LED, use a white lens. The illumination color will be dull if a different color is used. Notes on LED Illuminated Units [Protection Example 1] For AC circuit Terminal No. X1 X2 Polarity Positive Negative LED lamps consist of semiconductors. If the applied voltage exceeds the rated voltage, LED elements may deteriorate due to overheat, resulting in significant decrease in luminance, hue change, or failure of lighting. Also, if an extraneous noise, transient voltage, or transient current is applied to the circuit, similar effects may occur. When using LED lamps, observe the following instructions. Rated Voltage The LED lamps are rated at 6V, 12V, or 24V AC/DC, and can be used within 10% the rated voltage of either AC or DC. DC Power 1. Switching power supply Regulated voltage from switching power supply is best suited. Make sure to use within the rated voltage of the LED lamp. 2. Rechargeable battery Note that the battery voltage may exceed the rated volt age of the LED lamp while the battery is being charged and immediately after the charging is complete. Be sure to use the LED lamp on a voltage of 10% the rated voltage. 3. Full-wave rectification Since the LED lamp is AC/DC compatible, a diode bridge for rectification is not necessary. If the LED lamp is used on a full-wave rectification current through a diode bridge, the rectifier diodes will reduce the voltage, resulting in lower luminance. 4. Single-phase half-wave rectification This is not suitable for the power source of LED lamps. Use constant-voltage DC power. Noise LED elements deteriorate due to extraneous noise, result ing in significant decrease in luminance, hue change, or failure of lighting. When such effects are anticipated, take a protection measure shown below, such as RC elements or a surge absorber. 70 LED with transformer C C LED with transformer LED Relay Ry coil or solenoid R LED R (Reference values) R: 120 C: 0.1 F [Protection Example 2] For DC circuit + (Reference values of the diode) Forward current: More than the Ry coil current Reverse withstand voltage: Ry coil current 10 Relay Ry coil or solenoid LED Diode - Countermeasures against Dim Lighting 1. Leakage currents through the transistors or a contact protection circuit may cause the LED lamp to illuminate dimly even when the output is off. 2. When the LED lamp is illuminated by a transistor output, take the following measure. [Circuit Example] Connect shunt resistor R in parallel with the LED lamp. R LED Io Io: Leakage current when the output is off R: Shunt resistor o30 o30 Series Diecast Zinc Switches & Pilot Lights Heavy duty switches for tough industrial usage * Degree of protection: IP65 (IEC 60529) * UL, CSA approved, and EN compliant Applicable Standards Mark File No. or Organization UL 508 UL Listing File No. E68961 CSA C22.2 No.14 CSA File No. LR21451 EN60947-5-1 EU Low Voltage Directive GB14048.5 CCC No. 200501030514650 Specifications and Ratings Contact Ratings Weight (Examples) Contact Block Pushbuttons Rated Insulation Voltage Illuminated Pushbuttons Selector Switches Rated Continuous Current Illuminated Selector Switches Contact Ratings by Utilization Category Selector Pushbuttons IEC 60947-5-1 BST (o30 series) 600V Weight (approx.) 10A AC-15 (A600) DC-13 (P600) 135g (ABD 122N) 71g (APD122DN) 116g (ALD22211DN) 125g (ASD222N) 168g (ASD2K22N) 147g (ASLD22222DN) 116g (ASBD211N-A03) Characteristics Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V 10A 10A 10A 5A 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types) BST Contact Block (Light Gray) Interlocking Groove M3.5 Terminal Screw Contact Blocks Single-pole Contact Block Contact 1NO Inspection Window Push Rod Mounting Screw 1NC 1EM (early make) 1LB (late break) Part BST BST010 BST001 BST010S BST001S No. Push Rod Green Red Black White Note: BST contact blocks are not interchangeable with dark gray BS contact blocks used for o30 switches & pilot lights. Specifications, ratings, and mounting hole layouts are the same as o30 switches & pilot lights. See "o30 Series Switches & Pilot Lights" on page 16. 71 o30 o30 Series Diecast Zinc Switches & Pilot Lights Ordering Information Standard Units Terminal Cover * Specify an operator or Lens/LED Color Code in the Part No. * Black, green, and red colored buttons are included with flush pushbuttons. * Terminal covers, nameplates, and accessories are ordered separately. * When a terminal cover is required, order an applicable terminal cover referring to page 59. The Part No. development charts shown below can be used to specify switches & pilot lights other than those listed on the following pages. o30 Series Diecast Zinc Pushbuttons ABD2 11 N R Button color code Contact Configuration 10: 1NO 01: 1NC 11: 1NO-1NC 20: 2NO 02: 2NO 22: 2NO-2NC 40: 4NO 04: 4NO 13: 1NO-3NC 31: 3NO-1NC 30: 3NO 03: 3NC 12: 1NO-2NC 21: 2NO-1NC Note: * Mushroom pull AZD3 can have a maximum of two contact blocks. * Mushroom push pull AYD31 can have a maximum of two contact blocks. o30 Series Diecast Zinc Pilot Lights APDE 1 99 D N R Lens/LED Color Code Operating voltage code Lamp receptacle: (blank): BA9S (LSTD-6 LED) 72 o30 Series Diecast Zinc Illuminated Pushbuttons ALDE 2 16 11 D N R Lens/LED Color Code Contact configuration 11: 1NO-1NC 20: 2NO 02: 2NC 31: 3NO-1NC 22: 2NO-2NC 13: 1NO-3NC 40: 4NO 04: 4NC Operating voltage code Lamp receptacle (blank): BA9S (LSTD-6 LED) Note: * Illuminated pushbuttons cannot have an odd number of contact blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and 3NC. o30 o30 Series Diecast Zinc Switches & Pilot Lights o30 o30 Series Diecast Zinc Selector Switch ASD 2 L 11 N Contact configuration Operator (blank): Knob L: Lever Number of positions o30 Series Diecast Zinc Illuminated Selector Switch ASLD 2 16 22 D N R Lens/LED Color Code Contact configuration Operating voltage code Number of positions o30 Series Diecast Zinc Key Selector Switch ASD 2 K 20 N B Key removable position code 2-position * Maintained (blank): Removable in all positions B: Removable in left only C: Removable in right only * Spring return from right (blank): Removable in left only * Spring return from left (blank): Removable in right only 3-position * Maintained (blank): Removable in all positions B: Removable in left and center C: Removable in right and center D: Removable in center only E: Removable in right and left G: Removable in left only H: Removable in right only * Spring return from right (blank): Removable in left and center D: Removable in center only G: Removable in left only * Spring return from left (blank): Removable in right and center D: Removable in center only H: Removable in right only * Spring return two-way (blank): Removable in center only Contact configuraion Number of positions Note: * The key cannot be removed in the return position. 73 o30 o30 Diecast Zinc Series Pushbuttons Flush / Extended / Extended with Half Shroud / Extended with Full Shroud Flush ABD1 Momentary Contact Part No. 1NO ABD110N 1NC ABD101N 1NO-1NC ABD111N 2NO ABD120N 2NC ABD102N 2NO-2NC ABD122N Flush AOD1 1NO 1NC Maintained AOD110N AOD101N 1NO-1NC AOD111N 2NO AOD120N 2NC AOD102N Button Color Dimensions (mm) Code Black (B), green (G), and red (R) buttons are supplied with each unit. Specify S, Y, or W when a blue, yellow, or white button is required. Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 36 Operation o35 Shape 23 40 68 (1 to 2 blocks) 91 (3 to 4 blocks) 9 2NO-2NC AOD122N ABD210N 1NC ABD201N 1NO-1NC ABD211N ABD220N 2NC ABD202N Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 2NO-2NC ABD222N Extended AOD2 Maintained 1NO AOD210N 1NC AOD201N 5.5 AOD220N 2NC AOD202N 23 53 (1 or 2 blocks) 40 9 14.5 76 (3 or 4 blocks) 1NO-1NC AOD211N 2NO o40 2NO o25 Momentary 1NO o35 Extended ABD2 2NO-2NC AOD222N ABGD210N 1NC ABGD201N 1NO-1NC ABGD211N 2NO ABGD220N 2NC ABGD202N 2NO-2NC ABGD222N Extended with Half Shroud AOGD2 Maintained 1NO AOGD210N 1NC AOGD201N 1NO-1NC AOGD211N 2NO AOGD220N 2NC AOGD202N Specify a button color code in place of in the Part No. B: G: R: S: W: Y: black green red blue white yellow M3.5 Terminal Screw Panel Thickness 0.8 to 3.5 5.5 23 49.5 (1 or 2 blocks) o40 Momentary 1NO o25 o27 o35 Extended with Half Shroud ABGD2 40 20.5 72.5 (3 or 4 blocks) 2NO-2NC AOGD222N ABFD210N 1NC ABFD201N 1NO-1NC ABFD211N 2NC ABFD202N M3.5 Terminal Screw Panel Thickness 0.8 to 6 2NO-2NC ABFD222N Extended with Full Shroud AOFD2 1NO 1NC Maintained AOFD210N AOFD201N 1NO-1NC AOFD211N 2NO AOFD220N 2NC AOFD202N 2NO-2NC AOFD222N * Round bezel and shroud (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block * Other contact configurations are also available. See page 72. 74 5.5 23 51.5 (1 or 2 blocks) 74.5 (3 or 4 blocks) o40 ABFD220N o35 2NO o25 Momentary 1NO o28.5 Extended with Full Shroud ABFD2 40 17 o30 o30 Diecast Zinc Series Pushbuttons o30 Mushroom / Jumbo Mushroom Pushbuttons Operation Mushroom ABD3 Momentary Contact Part No. 1NO ABD310N 1NC ABD301N Button Color Dimensions (mm) Code 1NO-1NC ABD311N 2NO ABD320N 2NC ABD302N Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw AOD310N 1NC AOD301N AOD320N 2NC AOD302N 2NO-2NC AOD322N Mushroom with Full Shroud ABGD3 Momentary 1NO ABGD310N 1NC ABGD301N 76 (3 or 4 blocks) B: G: R: W: Y: Maintained 22 black green red white yellow 1NO-1NC ABGD311N 2NO ABGD320N 2NC ABGD302N M3.5 Terminal Screw 2NO-2NC ABGD322N Mushroom with Full Shroud AOGD3 40 53 (1 or 2 blocks) 1NO-1NC AOD311N 2NO 23 5.5 1NO AOGD310N 1NC AOGD301N Panel Thickness 0.8 to 6.5 o48 Maintained 1NO o40 2NO-2NC ABD322N Mushroom AOD3 o40 Shape 5.5 23 52 (1 or 2 blocks) 23 75 (3 or 4 blocks) 1NO-1NC AOGD311N 2NO AOGD320N 2NC AOGD302N 2NO-2NC AOGD322N Momentary ABD410N 1NC ABD401N M3.5 Terminal Screw 1NO-1NC ABD411N 2NO ABD420N 2NC ABD402N 5.5 Momentary 1NO ABGD410N 1NC ABGD401N 1NO-1NC ABGD411N 2NO ABGD420N 2NC ABGD402N 23 53 (1 or 2 blocks) 29 76 (3 or 4 blocks) 2NO-2NC ABD422N Jumbo Mushroom with Shallow Shroud ABGD4 Panel Thickness 0.8 to 7.5 o65 1NO M3.5 Terminal Screw B: DG: DR: G: R: Y: black dark green dark red green red yellow Panel Thickness 0.8 to 7.5 o65 o75 Jumbo Mushroom ABD4 5.5 23 53 (1 or 2 blocks) 29 76 (3 or 4 blocks) 2NO-2NC ABGD422N Momentary 1NO ABFD410N 1NC ABFD401N M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o75 Jumbo Mushroom with Deep Shroud ABFD4 1NO-1NC ABFD411N 2NO ABFD420N 2NC ABFD402N 5.5 23 53 (1 or 2 blocks) 32.5 76 (3 or 4 blocks) 2NO-2NC ABFD422N * Specify a button color code in place of in the Part No. * Round bezel and shroud (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block * Other contact configurations are also available. See page 72. 75 o30 o30 Diecast Zinc Series Pushbuttons Pushlock Turn Reset / Push Turn Lock / Pull / Push-Pull / Pin Lock Pushbuttons AVD322N 1NO AJD310N 1NC AJD301N 1NO-1NC AJD311N 2NO AJD320N 2NC AJD302N 2NO-2NC AJD322N 1NO AZD310N 1NO-1NC AZD311N 2NO AZD320N 2NC AZD302N 1NO-1NC AYD3111N 2NO AYD3120N 2NC AYD3102N 1NO ABD8P10N 1NC ABD8P01N 1NO-1NC ABD8P11N 2NO ABD8P20N 2NC ABD8P02N 2NO-2NC 40 53 (1 or 2 blocks) 24 76 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: black G: green R: red Y: yellow 23 5.5 L H 40 53 (1 or 2 blocks) 24 76 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: black G: green R: red S: blue Y: yellow 23 5.5 40 53 (1 or 2 blocks) 30.5 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 5.5 23 53 (1 or 2 blocks) ABD8P22N * Specify a button color code in place of in the Part No. * Round bezel (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block. * Other contact configurations are also available. See page 72. * Pushlock Turn Reset: Button is maintained when pressed and is reset when turned clockwise. Red buttons only. Note: AVD3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use XN or HN series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Button is locked when turned clockwise in the depressed position and is reset when turned counterclockwise. * Pull: Pulling the button operates the contacts. Up to 2 contact blocks (1 layer) can be mounted on pull switches. * Push-Pull: Button is maintained in both depressed and reset positions. Up to 2 contact blocks (1 layer) can be mounted on AYD31 push-pull switches. Note: AYD31 push-pull switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Pin Lock: Button can be locked in either depressed or reset position by inserting the pin. Pad lock with a o5mm pin can also be used to lock the button. 23 5.5 36 2NO-2NC 36 AVD302N 36 2NC R: red Y: yellow PUS AVD320N o40 AVD311N 2NO o40 1NO-1NC Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw o40 Pin Lock ABD8P AVD301N 52 Mushroom Push-Pull AYD31 AVD310N 1NC Dimensions (mm) Code K OC Mushroom Pull AZD3 1NO Button Color o40 Mushroom Push Turn Lock AJD3 Part No. o28 Mushroom Pushlock Turn Reset AVD3 Contact o35 Shape 40 28.5 49 76 (3 or 4 blocks) Contact Operation Pull Switch (Spring Return) Contact AZD3 Normal Pull 1NO 1NC 1NO-1NC 2NO 2NC Push-Pull Switch (Maintained) Contact AYD31 Push Pull 1NO-1NC 2NO 2NC Note: Pull and push-pull switches can have a maximum of two contact blocks. 76 o30 o30 Diecast Zinc Series Pilot Lights o30 APD1 / APDE1 Dome Pilot Lights Shape Lamp Receptacle Lamp Part No. Lens/LED Color Code Applicable Lamp Dome APD1 APDE1 Without Lamp BA9S APD199N A: G: S: DNY: amber green blue yellow C: clear R: red W: white See page 17 for lamps. LED BA9S APD1DN A: PW: S: Y: amber G: green pure white R: red blue W: white yellow Operating Voltage Code Specify an operating voltage code in place of in the Part No. Input Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC Full Voltage Transformer * Specify a lens/LED color code in place of in the Part No. * Use a pure white (PW) LED for yellow (Y) illumination.. Dimensions Full Voltage 9 29.5 o40 o25 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 40 21 Transformer M3.5 Terminal Screw 9 64.5 o40 o35 o25 Panel Thickness 0.8 to 7.5 40 21 All dimensions in mm. 77 o30 o30 Diecast Zinc Series Illuminated Pushbuttons ALD2 / AOLD2 Round Extended Illuminated Pushbuttons Round Extended ALD2 AOLD2 Lamp Contact 1NO-1NC ALD29911N 2NO ALD29920N 2NC ALD29902N 1NO-1NC ALD211DN 2NO Screws ALD2 20DN 2NC ALD202DN 1NO-1NC AOLD29911N 23 2NO AOLD29920N 119.5 (4 blocks) 2NC AOLD29902N 1NO-1NC AOLD211DN 2NO AOLD220DN 2NC AOLD202DN Without Lamp Momentary LED BA9S Without Lamp Maintained Applicable Lamp Part No. LED M3.5 Terminal 96.5 (2 blocks) Panel Thickness 0.8 to 7.5 See page 17 for lamps. o35 Operation o24.6 Lamp Receptacle Shape 18.5 Color Code and Operating Voltage Code Specify a code in place of and in the Part No. Lens/LED Color Code Operating Voltage Code Without Lamp LED A: amber C: clear G: green R: red S: blue W: white DNY: yellow A: G: PW: R: S: W: Y: 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC amber green pure white red blue white yellow Input Full Voltage Transformer * Use a pure white (PW) LED for yellow (Y) illumination.. Dimensions ALD2/AOLD2 Full Voltage ALD2/AOLD2 BA9S/Transformer M3.5 Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 23 24 o40 o24 40 40 9 9 63 (2 blocks) 86 (4 blocks) o35 o40 o35 o24 5.5 Panel Thickness 0.8 to 7.5 M3 Terminal Screw M3 Terminal Screw 97.5 (2 blocks) 120.5 (4 blocks) 24 All dimensions in mm. 78 o30 o30 Diecast Zinc Series Illuminated Pushbuttons o30 ALFD2 / AOLFD2 Round Extended with Full Shroud Illuminated Pushbuttons Round Extended with Full Shroud ALFD2 AOLFD2 Lamp Contact Without Lamp Momentary LED BA9S Without Lamp Maintained LED Applicable Lamp Part No. 1NO-1NC ALFD29911N 2NO ALFD29920N 2NC ALFD29902N 1NO-1NC ALFD211DN 2NO ALFD220DN 2NC Screws02DN 0.8 to 7.5 ALFD2 See page 17 M3.5 Terminal Panel Thickness 1NO-1NC AOLFD29911N 2NO 23 AOLFD29920N 2NC 119.5 (4 blocks) AOLFD29902N for lamps. o35 Operation o24.6 Lamp Receptacle Shape 18.5 96.5 (2 blocks) 1NO-1NC AOLFD211DN 2NO AOLFD220DN 2NC AOLFD202DN Color Code and Operating Voltage Code Specify a code in place of and in the Part No. Lens/LED Color Code Operating Voltage Code Without Lamp LED A: amber C: clear G: green R: red S: blue W: white DNY: yellow A: G: PW: R: S: W: Y: amber green pure white red blue white yellow 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC Input Full Voltage Transformer * Use a pure white (PW) LED for yellow (Y) illumination. Dimensions ALFD2/AOLFD2 Transformer 23 62 (2 blocks) 84 (4 blocks) M3 Terminal Screw Panel Thickness 0.8 to 6 40 40 25 o40 o40 o35 o30 5.5 M3.5 Terminal Screw Panel Thickness 0.8 to 6 o35 M3 Terminal Screw M3.5 Terminal Screw o30 ALFD2/AOLFD2 Full Voltage 96.5 (2 blocks) 119.5 (4 blocks) 25 All dimensions in mm. 79 o30 o30 Diecast Zinc Series Illuminated Pushbuttons ALD3 / AOLD3 Mushroom (o40) Illuminated Pushbuttons Lamp Receptacle Shape Operation o40 Mushroom ALD3 AOLD3 Lamp Contact Without Lamp Momentary LED BA9S Without Lamp Maintained LED 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Applicable Lamp Part No. ALD39911DN ALD39920DN ALD39902DN ALD311DN ALD320DN ALD302DN AOLD39911DN AOLD39920DN AOLD39902DN AOLD311DN AOLD320DN AOLD302DN See page 17 for lamps. Color Code and Operating Voltage Code Specify a code in place of and in the Part No. Lens/LED Color Code Operating Voltage Code A: G: R: W: Y: amber green red white yellow Use a pure white (PW) LED for yellow (Y) illumination.. 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC Input Full Voltage Transformer Dimensions 5.5 23 5.5 63 (2 blocks) 86 (4 blocks) 40 24 M3.5 TerminalPanel Screw Thickness 0.8 to 7.5 Panel Thickness 0.8 to 7.5 M3 Terminal Screw 40 40 97.5 (2 blocks) 120.5 (4 blocks) 97.5 (224 blocks) 120.5 (4 blocks) 36 o40 M3 Terminal Screw 36 o40 23 2463 (2 blocks) 86 (4 blocks) M3.5 Terminal Screw 36 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 Panel Thickness 0.8 to 7.5 M3 Terminal Screw o40 M3 Terminal Screw 36 M3.5 Terminal Screw ALD3/AOLD3 Transformer o40 ALD3/AOLD3 Full Voltage 40 24 All dimensions in mm. 80 o30 o30 Diecast Zinc Series Illuminated Pushbuttons o30 AVLD3/ AVLDE3 Mushroom Pushlock Turn Reset Illuminated Pushbuttons Mushroom Pushlock Turn Reset AVLD3 AVLDE3 Without Lamp Contact Part No. 1NO-1NC AVLD39911NR 2NO AVLD39920NR 2NC AVLD39902NR 1NO-1NC AVLD311DNR Applicable Lamp M3.5 Terminal Screws BA9S Panel Thickness 0.8 to 7.5 See page 17 for lamps. o35 Lamp o24.6 Lamp Receptacle Shape 23 LED 2NO AVLD320DNR96.5 (2 blocks) 2NC AVLD302DNR 18.5 119.5 (4 blocks) Color Code and Operating Voltage Code Specify a code in place of and in the Part No. Note: When ordering 6V, 12V, 24V AC/DC units, specify Input Operating Voltage Code 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC 16: 100/110V AC 126: 120V AC 26: 200/220V AC 246: 240V AC 386: 380V AC 46: 400/440V AC "E " before the operating voltage code. Example: AVLDE311NR Full Voltage Transformer * Color code: R (red) * Pushlock Turn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only. Note: AVLD3 and AVLDE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use XN or HN series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). Dimensions AVLD3 BA9S/Full Voltage AVLD3 BA9S/Transformer Panel Thickness 0.8 to 7.5 5.5 23 63 (2 blocks) 86 (4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 5.5 23 97.5 (2 blocks) 120.5 (4 blocks) 36 36 40 24 o40 M3 Terminal Screw o40 M3.5 Terminal Screw M3 Terminal Screw 40 24 All dimensions in mm. 81 o30 o30 Diecast Zinc Series Selector Switches No. of Positions ASD Selector Switches (Knob Operator) ASD 90 2-position Contact Configuration 1NO 1NO-1NC 2NO 2NO-2NC Contact Configuration 45 3-position 2NO 4NO 2NO-2NC 2NC 4NC Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 Contact L NO L R Contact Block L R Spring Return from Left L R R ASD210N ASD2110N ASD2210N ASD211N ASD2111N ASD2211N ASD220N ASD2120N ASD2220N ASD222N ASD2122N ASD2222N Dummy NO NC NO NO NO NC NO NC Spring Return from Right Maintained Operator Position -- Mounting Position Contact L 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC C Spring Return from Right Maintained Operator Position L R C L R C Spring Return from Left R L C Spring Return Two-way R L C ASD320N ASD3120N ASD3220N ASD3320N ASD340N ASD3140N ASD3240N ASD3340N ASD322N ASD3122N ASD3222N ASD3322N ASD302N ASD3102N ASD3202N ASD3302N ASD304N ASD3104N ASD3204N ASD3304N R * Knob: Black * Round bezel (metal): Chrome-plated * Selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] Contact Block Mounting Position and Contact Configuration Chart Dimensions 1 Panel Thickness 0.8 to 7.5 90 M3.5 Terminal Screw 1 2 3 4 NO NO NC NC C R 45 45 Operator Position o35 L 3 Right o40 Center Left 4 2 5.5 23 53 (1 or 2 blocks) 40 21 76 (4 blocks) All dimensions in mm. 82 o30 o30 Diecast Zinc Series Selector Switches o30 No. of Positions ASDL Selector Switches (Lever Operator) ASDL 90 2-position Contact Configuration 1NO 1NO-1NC 2NO 2NO-2NC Contact Configuration 45 3-position 2NO 4NO 2NO-2NC 2NC 4NC Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 Contact L NO L R Contact Block L R L R Spring Return from Left R ASD2L10N ASD21L10N ASD22L10N ASD2L11N ASD21L11N ASD22L11N ASD2L20N ASD21L20N ASD22L20N ASD2L22N ASD21L22N ASD22L22N Dummy NO NC NO NO NO NC NO NC Spring Return from Right Maintained Operator Position -- Spring Return from Right Maintained Operator Position C Mounting Position Contact L 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC C L R L R C Spring Return from Left R L C Spring Return Two-way R L C ASD3L20N ASD31L20N ASD32L20N ASD33L20N ASD3L40N ASD31L40N ASD32L40N ASD33L40N ASD3L22N ASD31L22N ASD32L22N ASD33L22N ASD3L02N ASD31L02N ASD32L02N ASD33L02N ASD3L04N ASD31L04N ASD32L04N ASD33L04N R * Lever: Black * Round bezel (metal): Chrome-plated * Selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] Dimensions Center Left 4 2 1 Panel Thickness 0.8 to 7.5 90 M3.5 Terminal Screw 1 2 3 4 NO NO NC NC C R 45 45 Operator Position o35 L 3 Right o40 Contact Block Mounting Position and Contact Configuration Chart 5.5 23 53 (1 or 2 blocks) 40 21.5 76 (4 blocks) All dimensions in mm. 83 o30 o30 Diecast Zinc Series Selector Switches ASDK Key Selector Switches No. of Positions ASDK 90 2-position Contact Configuration Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 1NO 1NO-1NC 2NO 2NO-2NC Contact Configuration L NO NO NC NO NO NO NC NO NC R ASD22K10N ASD2K11N ASD21K11N ASD22K11N ASD2K20N ASD21K20N ASD22K20N ASD2K22N ASD21K22N ASD22K22N -- Maintained Operator Position C 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC 4NC L R ASD21K10N L 2NC L Spring Return from Left ASD2K10N Contact 2NO-2NC R Spring Return from Right Mounting Position 4NO L R Dummy Contact Block 2NO 45 3-position Contact Maintained Operator Position C L R R Spring Return from Right L C Spring Return from Left R C L Spring Return Two-way R L C ASD3K20N ASD31K20N ASD32K20N ASD33K20N ASD3K40N ASD31K40N ASD32K40N ASD33K40N ASD3K22N ASD31K22N ASD32K22N ASD33K22N ASD3K02N ASD31K02N ASD32K02N ASD33K02N ASD3K04N ASD31K04N ASD32K04N ASD33K04N R * Cylinder: Black * Round bezel (metal): Chrome-plated * On the spring-returned, the keys can be released only from the maintained positions. On the maintained, the key can be released from every position. Key retained positions are also available. See page 73. * Key selector switches are supplied with two standard keys. * Key selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] Center Left 2 L 3 1 1 2 3 4 NO NO NC NC C Right R Panel Thickness 0.8 to 7.5 45 Operator Position 45 5.5 23 9 53 (1 or 2 blocks) 16.5 76 (4 blocks) 84 90 M3.5 Terminal Screw o35 4 Dimensions o40 Contact Block Mounting Position and Contact Configuration Chart 40 38 All dimensions in mm. o30 o30 Diecast Zinc Series Illuminated Selector Switches o30 ASLD Illuminated Selector Switches 90 2-position ASLD (Base BA9S) Contact Configuration Contact Block Mounting Position Contact 1 NO 2 NC 1 NO 2 NO 1 2 3 4 NO NC NO NC Maintained Operator Position L Lamp L Spring Return from Right L R Spring Return from Left L R R R Without Lamp ASLD29911N ASLD219911N ASLD229911N LED ASLD211DN ASLD2111DN ASLD2211DN Without Lamp ASLD29920N ASLD219920N ASLD229920N LED ASLD220DN ASLD2120DN ASLD2220DN Without Lamp ASLD29922N ASLD219922N ASLD229922N LED ASLD222DN ASLD2122DN ASLD2222DN 1NO-1NC 2NO 2NO-2NC Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Operating Voltage Code A: G: R: S: W: Y: amber green red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. Input 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 100/110V AC 136: 120V AC 26: 200/220V AC 256: 240V AC 386: 380V AC 46: 400/440V AC Transformer * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] Contact Block Mounting Position and Contact Configuration Chart Dimensions 3 1 L 1 2 3 4 NO NC NO NC R 90 Operator Position 45 45 (including nameplate) o40 M3 Terminal Screw 2 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screws o25 4 Right o35 Left 5.5 40 23 63 (2 blocks) A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) A: Full voltage B: Transformer 9 28 All dimensions in mm. 85 o30 o30 Diecast Zinc Series Illuminated Selector Switches ASLD Illuminated Selector Switches 45 3-position Contact Configuration Contact Block Maintained Spring Return from CRight Spring Return fromC left Spring Return Two-way Without Lamp ASLD39920N ASLD319920N ASLD329920N ASLD339920N LED ASLD3120DN ASLD3220DN ASLD3320DN Operator Position Lamp L C R L L R R L C R Mounting Position Contact L 1 NO 2 NO 1 NC Without Lamp ASLD39902N ASLD319902N ASLD329902N ASLD339902N 2 NC LED ASLD3102DN ASLD3202DN ASLD3302DN 1 2 3 4 1 2 3 4 1 2 3 4 NO NO NC NC NO NO NO NO NC NC NC NC Without Lamp ASLD39922N ASLD319922N ASLD329922N ASLD339922N LED ASLD3122DN ASLD3222DN ASLD3322DN Without Lamp ASLD39940N ASLD319940N ASLD329940N ASLD339940N LED ASLD3140DN ASLD3240DN ASLD3340DN Without Lamp ASLD39904N ASLD319904N ASLD329904N ASLD339904N LED ASLD3104DN ASLD3204DN ASLD3304DN C R 2NO ASLD320DN 2NC ASLD322DN ASLD340DN ASLD304DN Color Code and Operating Voltage Code Specify a code in place of or in the Part No. Lens/LED Color Code Operating Voltage Code A: G: R: S: W: Y: amber green red blue white yellow Use a pure white (PW) LED for yellow (Y) illumination. Input Type 66: 6V AC/DC 11: 12V AC/DC 22: 24V AC/DC Full voltage 16: 100/110V AC 136: 120V AC 26: 200/220V AC 256: 240V AC 386: 380V AC 46: 400/440V AC Transformer Contact Block Mounting Position and Contact Configuration Chart 4 Dimensions Center Left 1 M3.5 Terminal Screws M3 Terminal Screw 2 L 3 Right 1 2 3 4 NO NO NC NC C R Panel Thickness 0.8 to 7.5 (including nameplate) Operator Position 90 45 45 o40 4NC o35 4NO o25 2NO2NC ASLD302DN 5.5 40 23 63 (2 blocks) A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) 9 28 A: Full voltage B: Transformer All dimensions in mm. 86 o30 o30 Diecast Zinc Series Selector Pushbuttons o30 ASBD2 Ring Operator / ASBD2L Lever Operator Selector Pushbuttons Ring/Lever Contact Configuration Shape Ring Operator Contact Block Circuit Code Color Pushbutton Ring Operator (90 2-Position) ASBD2 A03 1NO-1NC G03 A08 C10 D10 Lever Operator (90 2-Position) ASBD2L 2NO-2NC E10 F10 G10 Lever Operator Mounting Position Contact 1 2 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 NO NC NO NC NO NC NO NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC Normal Push Normal Part No. Push Blocked Part No. ASBD211N-A03 ASBD2L11N-A03 ASBD211N-G03 ASBD2L11N-G03 ASBD222N-A08 ASBD2L22N-A08 ASBD222N-C10 ASBD2L22N-C10 B: black G: green ASBD222N-D10 ASBD2L22N-D10 R: red Y: yellow ASBD222N-E10 ASBD2L22N-E10 ASBD222N-F10 ASBD2L22N-F10 Blocked ASBD222N-G10 ASBD2L22N-G10 * Specify a button color code in place of in the Part No. * Ring/Lever (Metal): Chrome-plated Notes: 1. Circuit Code G: The pushbutton does not operate when the ring or lever operator is turned to the right position. 2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button. 3. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure may be caused. 4. When installing the lever operator, make sure that the lever is not in the horizontal position. Otherwise, shock resistance may be degraded. Contact Block Mounting Position 1 M3.5 Terminal Screw Dimensions 5.5 23 23 53 (1 or 2 blocks) 26.5 76 (3 or 4 blocks) 53 (2 blocks) 76 (4 blocks) 5.5 R50 o40 o35 M3.5 Terminal Screw 37 20 37 Lever Operator (90 2-position) ASBD2L Panel Thickness 0.8 to 7.5 (including nameplate) o28 Ring Operator (90 2-position) ASBD2 Panel Thickness 0.8 to 7.5 (including nameplate) o34 3 2 50 4 40 25 M3 Setscrew (The actual screw is located on the opposite side) 87 o30 o30 Diecast Zinc Series Accessories and Replacement Parts Accessories (For Diecast Zinc Series Only) Shape Material Part No. For other accessories, see pages 59 to 68. Ordering No. Package Quantity Description Metal Bezel OG-81 OG-81PN02 2 OG-82 OG-82 1 Chrome-plated Flush (Octagonal) Extended (Octagonal) * Cannot be used with half-shrouds. Spare Key Metal TW-SK-0 TW-SK-0PN02 2 * For key selector switches Maintenance Parts (For Diecast Zinc Series Only) Shape Specification Button Flush Extended Mushroom Polyacetal Jumbo Mushroom Dummy Block Polyamide Selector Operator Lever Knob Color Insert Polyacetal Part No. Ordering No. Package Quantity Description Specify a color code in place of . B (black), G (green), R (red), S (blue), W (white), Y (yellow) * Above colors are used for o30 diecast zinc switches & pilot lights (light colored operator units). ABN1BN- ABN1BN-PN05 5 ABN2BN- ABN2BN-PN05 5 ABN3BN- ABN3BN-PN02 2 ABN4BN- ABN4BN- 1 Specify a color code in place of . B (black), G (green), R (red), S (blue), Y (yellow) 10 * Used for 1NO or 1NC contact blocks. * Snaps on to the operator unit. 2 Specify a color code in place of . B (blue), G (green), R (red) 5 Specify a color code in place of . B (black), G (green), R (red), S (blue), W (white), Y (yellow) BST-D BST-DPN10 ASNHT- ASNHL- ASNHT-PN02 TW-HC1 TW-HC1PN05 ASNHL-PN02 Safety Precautions * Turn off the power to the o30 diecast zinc switches & pilot lights before starting installation, removal, wiring, maintenance, and starting installation, removing, wiring, maintenance, and inspection of the products. Failure to turn power off may cause electrical shocks or fire hazard. * To avoid a burn on your hand, use the lamp holder tool when replacing lamps. * For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a tightening torque of 1.0 to 1.3 N*m. Failure to tighten terminal screws may cause overheat and fire. Instructions Tightening Torque for Terminal Screws Tighten the M3.5 terminal screws to a torque of 1.0 to 1.3 N*m. Replacement of Lamps Lamps can be replaced by using the lamp holder tool (OR-55) from the front of the panel. * How to remove To remove, slip the lamp holder tool onto the lamp head lightly. Then push slightly, and turn the lamp holder tool counterclockwise. * How to install To install, insert the lamp head into the lamp holder tool. Place the pins on the lamp base to the grooves in the lamp socket. Inset the lamp and turn it clockwise. Installation of LED Illuminated Units * When using full voltage LED illuminated units, provide protection against electrical noise, if necessary. See page 70 for notes on LED illuminated units. OR-55 www.idec.com Head Office 6-64, Nishi-Miyahara-2-Chome, Yodogawa-ku, Osaka 532-0004, Japan USA Germany Singapore Thailand Australia Taiwan IDEC Corporation IDEC Electrotechnik GmbH IDEC Izumi Asia Pte. Ltd. IDEC Asia (Thailand) Co., Ltd IDEC Australia Pty. Ltd. IDEC Taiwan Corporation Tel: +1-408-747-0550 Tel: +49-40-25 30 54 - 0 Tel: +65-6746-1155 Tel: +66-2-392-9765 Tel: +61-3-8523-5900 Tel: +886-2-2698-3929 opencontact@idec.com service@eu.idec.com info@sg.idec.com sales@th.idec.com sales@au.idec.com service@tw.idec.com Specifications and other descriptions in this brochure are subject to change without notice. 2017 IDEC Corporation, All Rights Reserved. EP1429-13 JUNE 2017 Hong Kong China/Shanghai China/Shenzhen China/Beijing Japan IDEC Izumi (H.K.) Co., Ltd. IDEC (Shanghai) Corporation IDEC (Shenzhen) Corporation IDEC (Beijing) Corporation IDEC Corporation Tel: +852-2803-8989 Tel: +86-21-6135-1515 Tel: +86-755-8356-2977 Tel: +86-10-6581-6131 Tel: +81-6-6398-2527 info@hk.idec.com idec@cn.idec.com idec@cn.idec.com idec@cn.idec.com marketing@idec.co.jp