MC68HC908GR60A MC68HC908GR48A MC68HC908GR32A Data Sheet M68HC08 Microcontrollers MC68HC908GR60A Rev. 5 04/2007 freescale.com MC68HC908GR60A MC68HC908GR48A MC68HC908GR32A Data Sheet To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://freescale.com/ FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. This product incorporates SuperFlash(R) technology licensed from SST. (c) Freescale Semiconductor, Inc., 2004, 2006, 2007. All rights reserved. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 3 Revision History The following revision history table summarizes changes contained in this document. For your convenience, the page number designators have been linked to the appropriate location. Revision History Date Revision Level April, 2004 N/A July, 2004 1 June, 2005 March, 2006 July, 2006 April, 2007 2 3 4 5 Page Number(s) Description Initial release N/A 9.7.3 Keyboard Interrupt Polarity Register -- Corrected description of KBIP7-KBIP0. 119 Table 13-6. ESCI LIN Control Bits -- Corrected Functionality definitions 174 13.9.1 ESCI Arbiter Control Register -- Corrected definition for ACLK bit. 179 13.9.3 Bit Time Measurement -- Corrected description of ACLK bit. 180 10.5 Clock Generator Module (CGM) -- Updated description to remove erroneous information. 122 Added 1.5.15 Unused Pin Termination 28 12.1 Introduction -- Replaced note 131 Table 13-6. ESCI LIN Control Bits -- Corrected functionality column. 174 The following sections were updated to show that a break interrupt inhibits input captures: 17.6 TIM1 During Break Interrupts 18.6 TIM2 During Break Interrupts 19.2.1.2 TIM During Break Interrupts 233 251 264 Figure 19-10. Normal Monitor Mode Circuit and Figure 19-11. Forced Monitor Mode -- Changed capacitor values 269 20.5 5.0-Vdc Electrical Characteristics -- Updated minimum value for low-voltage inhibit, trip rising voltage (VTRIPR). 279 20.9.1 CGM Component Specifications -- Updated values for feedback bias resistor 284 Figure 2-2. Control, Status, and Data Registers -- Replaced TBMCLKSEL with TMBCLKSEL to be compatible with development tool nomenclature 33 90 Chapter 5 Configuration Register (CONFIG) -- Replaced COPCLK with CGMXCLK 89 91 10.6.2 Stop Mode -- Replaced COPCLK with CGMXCLK 122 Figure 13-3. ESCI Module Block Diagram -- Changed BUS_CLK to Bus Clock and deleted reference to 4x BUSCLK 154 13.4.2 Transmitter -- Changed ESCIBDSRC to SCIBDSRC 156 13.9.1 ESCI Arbiter Control Register and 13.9.3 Bit Time Measurement -- Replaced one quarter with one half in the definition for ACLK = 1 179 180 Chapter 16 Timebase Module (TBM) -- Replaced TBMCLKSEL with TMBCLKSEL to be compatible with development tool nomenclature 222 223 20.5 5.0-Vdc Electrical Characteristics and 20.6 3.3-Vdc Electrical Characteristics -- Updated tables 279 281 20.9 Clock Generation Module (CGM) Characteristics -- Updated section to include the following: 20.9.1 CGM Operating Conditions 20.9.2 CGM Component Information 20.9.3 CGM Acquisition/Lock Time Information 284 284 285 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 4 Freescale Semiconductor List of Chapters Chapter 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Chapter 2 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Chapter 3 Analog-to-Digital Converter (ADC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Chapter 4 Clock Generator Module (CGM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Chapter 5 Configuration Register (CONFIG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Chapter 6 Computer Operating Properly (COP) Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Chapter 7 Central Processor Unit (CPU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Chapter 8 External Interrupt (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Chapter 9 Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Chapter 10 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Chapter 11 Low-Voltage Inhibit (LVI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Chapter 12 Input/Output (I/O) Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Chapter 13 Enhanced Serial Communications Interface (ESCI) Module . . . . . . . . . . . . . 151 Chapter 14 System Integration Module (SIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Chapter 15 Serial Peripheral Interface (SPI) Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Chapter 16 Timebase Module (TBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Chapter 17 Timer Interface Module (TIM1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Chapter 18 Timer Interface Module (TIM2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .241 Chapter 19 Development Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Chapter 20 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Chapter 21 Ordering Information and Mechanical Specifications . . . . . . . . . . . . . . . . . . 295 Appendix A MC68HC908GR48A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 Appendix B MC68HC908GR32A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 5 List of Chapters MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 6 Freescale Semiconductor Table of Contents Chapter 1 General Description 1.1 1.2 1.2.1 1.2.2 1.3 1.4 1.5 1.5.1 1.5.2 1.5.3 1.5.4 1.5.5 1.5.6 1.5.7 1.5.8 1.5.9 1.5.10 1.5.11 1.5.12 1.5.13 1.5.14 1.5.15 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features of the CPU08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply Pins (VDD and VSS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oscillator Pins (OSC1 and OSC2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Reset Pin (RST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Interrupt Pin (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Power Supply Pins (VDDA and VSSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL). . . . . . . . . . . . . . . . Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8) . . . . . . . . . . . . . . . . Port B I/O Pins (PTB7/AD7-PTB0/AD0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port C I/O Pins (PTC6-PTC0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port D I/O Pins (PTD7/T2CH1-PTD0/SS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD) . . . . . . . . . . . . . . . . . . . . . . . . . Port F I/O Pins (PTF7/T2CH5-PTF0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port G I/O Pins (PTG7/AD23-PTBG0/AD16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unused Pin Termination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 19 19 21 21 23 25 25 26 26 26 26 26 26 27 27 27 27 27 27 28 28 Chapter 2 Memory 2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Input/Output (I/O) Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Random-Access Memory (RAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 FLASH-1 Memory (FLASH-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.2 FLASH-1 Control and Block Protect Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.2.1 FLASH-1 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.2.2 FLASH-1 Block Protect Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.3 FLASH-1 Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.4 FLASH-1 Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.5 FLASH-1 Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 29 29 29 41 41 41 42 42 43 44 45 46 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 7 Table of Contents 2.6.6 FLASH-1 Program Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 FLASH-2 Memory (FLASH-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.2 FLASH-2 Control and Block Protect Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.2.1 FLASH-2 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.2.2 FLASH-2 Block Protect Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.3 FLASH-2 Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.4 FLASH-2 Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.5 FLASH-2 Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.6 FLASH-2 Program Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 48 48 48 50 50 50 50 51 52 53 54 55 56 56 56 Chapter 3 Analog-to-Digital Converter (ADC) 3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.1 ADC Port I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.2 Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.3 Conversion Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.4 Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.5 Accuracy and Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.6 Result Justification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Monotonicity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.1 ADC Analog Power Pin (VDDAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2 ADC Analog Ground Pin (VSSAD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.3 ADC Voltage Reference High Pin (VREFH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.4 ADC Voltage Reference Low Pin (VREFL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.5 ADC Voltage In (VADIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.1 ADC Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.2 ADC Data Register High and Data Register Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.2.1 Left Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.2.2 Right Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.2.3 Left Justified Signed Data Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.2.4 Eight Bit Truncation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8.3 ADC Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 59 59 59 61 62 62 62 62 63 63 63 63 64 64 64 64 64 65 65 65 65 67 67 68 68 69 69 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 8 Freescale Semiconductor Chapter 4 Clock Generator Module (CGM) 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.3.8 4.3.9 4.4 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 4.4.6 4.4.7 4.4.8 4.4.9 4.4.10 4.5 4.5.1 4.5.2 4.5.3 4.5.4 4.5.5 4.6 4.7 4.7.1 4.7.2 4.7.3 4.8 4.8.1 4.8.2 4.8.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Oscillator Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Phase-Locked Loop Circuit (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acquisition and Tracking Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual and Automatic PLL Bandwidth Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programming the PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Programming Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Base Clock Selector Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Amplifier Input Pin (OSC1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Amplifier Output Pin (OSC2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Analog Power Pin (VDDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oscillator Enable Signal (SIMOSCEN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oscillator Enable in Stop Mode Bit (OSCENINSTOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Output Frequency Signal (CGMXCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Base Clock Output (CGMOUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM CPU Interrupt (CGMINT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Bandwidth Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Multiplier Select Register High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Multiplier Select Register Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL VCO Range Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM During Break Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acquisition/Lock Time Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acquisition/Lock Time Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parametric Influences on Reaction Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Choosing a Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 71 71 73 73 73 74 74 75 77 77 78 78 79 79 79 79 79 79 79 79 80 80 80 81 82 83 84 84 85 85 85 86 86 86 86 86 87 Chapter 5 Configuration Register (CONFIG) 5.1 5.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 9 Table of Contents Chapter 6 Computer Operating Properly (COP) Module 6.1 6.2 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.4 6.5 6.6 6.7 6.7.1 6.7.2 6.8 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-On Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPD (COP Disable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPRS (COP Rate Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COP Module During Break Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 93 94 94 94 94 94 94 95 95 95 95 95 95 95 95 96 Chapter 7 Central Processor Unit (CPU) 7.1 7.2 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.4 7.5 7.5.1 7.5.2 7.6 7.7 7.8 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Condition Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Chapter 8 External Interrupt (IRQ) 8.1 8.2 8.3 8.4 8.5 8.6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IRQ Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IRQ Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 109 109 111 111 112 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 10 Freescale Semiconductor Chapter 9 Keyboard Interrupt Module (KBI) 9.1 9.2 9.3 9.4 9.5 9.5.1 9.5.2 9.6 9.7 9.7.1 9.7.2 9.7.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Module During Break Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Interrupt Enable Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Interrupt Polarity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 113 113 116 117 117 117 117 117 118 119 119 Chapter 10 Low-Power Modes 10.1 10.1.1 10.1.2 10.2 10.2.1 10.2.2 10.3 10.3.1 10.3.2 10.4 10.4.1 10.4.2 10.5 10.5.1 10.5.2 10.6 10.6.1 10.6.2 10.7 10.7.1 10.7.2 10.8 10.8.1 10.8.2 10.9 10.9.1 10.9.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Analog-to-Digital Converter (ADC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Break Module (BRK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Central Processor Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Generator Module (CGM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Computer Operating Properly Module (COP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Interrupt Module (IRQ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low-Voltage Inhibit Module (LVI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 121 121 121 121 121 121 121 121 122 122 122 122 122 122 122 122 122 123 123 123 123 123 123 123 123 123 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 11 Table of Contents 10.10 Enhanced Serial Communications Interface Module (ESCI) . . . . . . . . . . . . . . . . . . . . . . . . . . 10.10.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.10.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.11 Serial Peripheral Interface Module (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.11.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.11.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.12 Timer Interface Module (TIM1 and TIM2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.12.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.12.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.13 Timebase Module (TBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.13.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.13.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.14 Exiting Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.15 Exiting Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 123 123 124 124 124 124 124 124 124 124 124 125 126 Chapter 11 Low-Voltage Inhibit (LVI) 11.1 11.2 11.3 11.3.1 11.3.2 11.3.3 11.3.4 11.4 11.5 11.6 11.6.1 11.6.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Polled LVI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Forced Reset Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage Hysteresis Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LVI Trip Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LVI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 127 127 128 128 129 129 129 129 130 130 130 Chapter 12 Input/Output (I/O) Ports 12.1 12.2 12.3 12.3.1 12.3.2 12.3.3 12.4 12.4.1 12.4.2 12.5 12.5.1 12.5.2 12.5.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unused Pin Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port A Input Pullup Enable Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port C Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 131 135 135 136 137 138 138 138 140 140 140 142 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 12 Freescale Semiconductor 12.6 12.6.1 12.6.2 12.6.3 12.7 12.7.1 12.7.2 12.8 12.8.1 12.8.2 12.9 12.9.1 12.9.2 Port D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port D Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port E Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port F Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port G. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port G Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Direction Register G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 142 143 145 145 145 146 147 147 148 149 149 150 Chapter 13 Enhanced Serial Communications Interface (ESCI) Module 13.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.1 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.1 Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.2 Character Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.3 Break Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.4 Idle Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.5 Inversion of Transmitted Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.6 Transmitter Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.1 Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.2 Character Reception. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.3 Data Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.4 Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.5 Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.6 Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.7 Receiver Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.8 Error Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 ESCI During Break Module Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7.1 PTE0/TxD (Transmit Data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7.2 PTE1/RxD (Receive Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8 I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.1 ESCI Control Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.2 ESCI Control Register 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 151 153 153 153 156 156 156 157 158 158 158 158 159 160 160 161 161 163 164 164 164 164 164 165 165 165 165 165 166 167 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 13 Table of Contents 13.8.3 ESCI Control Register 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.4 ESCI Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.5 ESCI Status Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.6 ESCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.7 ESCI Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8.8 ESCI Prescaler Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9 ESCI Arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.1 ESCI Arbiter Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.2 ESCI Arbiter Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.3 Bit Time Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.4 Arbitration Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 170 173 173 174 175 177 179 180 180 180 Chapter 14 System Integration Module (SIM) 14.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2 SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2.1 Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2.2 Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2.3 Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3 Reset and System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.1 External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2 Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.1 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.2 Computer Operating Properly (COP) Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.3 Illegal Opcode Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.4 Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.5 Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.6 Monitor Mode Entry Module Reset (MODRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 SIM Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4.1 SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4.2 SIM Counter During Stop Mode Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4.3 SIM Counter and Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5 Exception Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.1 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.1.1 Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.1.2 SWI Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.1.3 Interrupt Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.2 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.3 Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5.4 Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.6.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7 SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.1 Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.2 SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.3 Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 186 186 186 186 187 187 187 188 188 189 189 189 189 190 190 190 190 190 190 191 193 193 196 196 196 196 197 198 199 199 199 200 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 14 Freescale Semiconductor Chapter 15 Serial Peripheral Interface (SPI) Module 15.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4.1 Clock Phase and Polarity Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4.2 Transmission Format When CPHA = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4.3 Transmission Format When CPHA = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4.4 Transmission Initiation Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 Queuing Transmission Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6.1 Overflow Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6.2 Mode Fault Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.8 Resetting the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.9 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.9.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.9.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.10 SPI During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11.1 MISO (Master In/Slave Out). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11.2 MOSI (Master Out/Slave In). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11.3 SPSCK (Serial Clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11.4 SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12 I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.1 SPI Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.2 SPI Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.3 SPI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 201 201 204 204 205 205 205 206 207 209 210 210 212 213 214 214 214 215 215 215 215 215 216 216 217 217 218 220 Chapter 16 Timebase Module (TBM) 16.1 16.2 16.3 16.4 16.5 16.6 16.6.1 16.6.2 16.7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBM Interrupt Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timebase Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 221 221 221 222 223 223 223 224 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 15 Table of Contents Chapter 17 Timer Interface Module (TIM1) 17.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.1 TIM1 Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3 Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3.1 Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3.2 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4.1 Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4.2 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4.3 PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.5 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.6 TIM1 During Break Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.7 Input/Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8 Input/Output Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.1 TIM1 Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.2 TIM1 Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.3 TIM1 Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.4 TIM1 Channel Status and Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.5 TIM1 Channel Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 225 225 228 228 229 229 229 230 230 231 231 232 232 233 233 233 233 235 236 236 239 Chapter 18 Timer Interface Module (TIM2) 18.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.1 TIM2 Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3 Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3.1 Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3.2 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4.1 Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4.2 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4.3 PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.6 TIM2 During Break Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 241 241 245 246 246 246 247 248 248 249 250 251 251 251 251 251 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 16 Freescale Semiconductor 18.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.7.1 TIM2 Clock Pin (T2CH0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0) . . . . . . . . . . . . . . . . . . . . . . 18.8 I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.1 TIM2 Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.2 TIM2 Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.3 TIM2 Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.4 TIM2 Channel Status and Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.5 TIM2 Channel Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 252 252 252 252 254 254 255 258 Chapter 19 Development Support 19.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2 Break Module (BRK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1.1 Flag Protection During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1.2 TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1.3 COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2 Break Module Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.1 Break Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.2 Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.3 Break Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.4 Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.3 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 Monitor Module (MON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.1 Normal Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.2 Forced Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.3 Monitor Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.4 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.5 Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.6 Baud Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.1.7 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3.2 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 261 261 264 264 264 264 265 265 266 266 266 267 267 271 271 271 272 272 272 272 276 Chapter 20 Electrical Specifications 20.1 20.2 20.3 20.4 20.5 20.6 20.7 20.8 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0-Vdc Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3-Vdc Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0-Volt Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3-Volt Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 277 278 278 279 281 283 283 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 17 Table of Contents 20.9 20.9.1 20.9.2 20.9.3 20.10 20.11 20.12 20.13 20.14 20.15 Clock Generation Module (CGM) Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Component Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGM Acquisition/Lock Time Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Interface Module Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 284 284 285 286 287 288 289 292 293 Chapter 21 Ordering Information and Mechanical Specifications 21.1 21.2 21.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 Appendix A MC68HC908GR48A A.1 A.2 A.3 A.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 305 305 308 Appendix B MC68HC908GR32A B.1 B.2 B.3 B.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 309 309 312 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 18 Freescale Semiconductor Chapter 1 General Description 1.1 Introduction The MC68HC908GR60A, MC68HC908GR48A, and MC68HC908GR32A are members of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. The information contained in this document pertains to all three devices with the exceptions noted in Appendix A MC68HC908GR48A and Appendix B MC68HC908GR32A. 1.2 Features For convenience, features have been organized to reflect: * Standard features * Features of the CPU08 1.2.1 Standard Features Features of the MC68HC908GR60A include: * High-performance M68HC08 architecture optimized for C-compilers * Fully upward-compatible object code with M6805, M146805, and M68HC05 Families * 8-MHz internal bus frequency * Clock generation module supporting 1-MHz to 8-MHz crystals * FLASH program memory security(1) * On-chip programming firmware for use with host personal computer which does not require high voltage for entry * In-system programming (ISP) * System protection features: - Optional computer operating properly (COP) reset - Low-voltage detection with optional reset and selectable trip points for 3.3-V and 5.0-V operation - Illegal opcode detection with reset - Illegal address detection with reset * Low-power design; fully static with stop and wait modes * Standard low-power modes of operation: - Wait mode - Stop mode 1. No security feature is absolutely secure. However, Freescale's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 19 General Description * * * * * * * * * * * * * * * * * * * * Master reset pin and power-on reset (POR) On-chip FLASH memory: - MC68HC908GR60A -- 60 Kbytes - MC68HC908GR48A -- 48 Kbytes - MC68HC908GR32A -- 32 Kbytes Random-access memory (RAM): - MC68HC908GR60A -- 2048 bytes - MC68HC908GR48A -- 1536 bytes - MC68HC908GR32A -- 1536 bytes Serial peripheral interface (SPI) module Enhanced serial communications interface (ESCI) module One 16-bit, 2-channel timer interface module (TIM1) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel One 16-bit, 6-channel timer interface module (TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel Timebase module with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external crystal 24-channel, 10-bit successive approximation analog-to-digital converter (ADC) 8-bit keyboard wakeup port with software selectable rising or falling edge detect, as well as high or low level detection Up to 53 general-purpose input/output (I/O) pins, including: - 40 shared-function I/O pins, depending on package choice - Up to 13 dedicated I/O pins, depending on package choice Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis. During output mode, pullups are disengaged. Internal pullups on IRQ and RST to reduce customer system cost High current 10-mA sink/source capability on all port pins Higher current 20-mA sink/source capability on PTC0-PTC4 and PTF0-PTF3 User selectable clockout feature with divide by 1, 2, and 4 of the bus or crystal frequency User selection of having the oscillator enabled or disabled during stop mode BREAK module (BRK) to allow single breakpoint setting during in-circuit debugging Available packages: - 32-pin low-profile quad flat pack (LQFP) - 48-pin low-profile quad flat pack (LQFP) - 64-pin quad flat pack (QFP) Specific features in 32-pin LQFP are: - Port A is only 4 bits: PTA0-PTA3; shared with ADC and KBI modules - Port B is only 6 bits: PTB0-PTB5; shared with ADC module - Port C is only 2 bits: PTC0-PTC1 - Port D is only 7 bits: PTD0-PTD6; shared with SPI, TIM1 and TIM2 modules - Port E is only 2 bits: PTE0-PTE1; shared with ESCI module MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 20 Freescale Semiconductor MCU Block Diagram * * Specific features in 48-pin LQFP are: - Port A is 8 bits: PTA0-PTA7; shared with ADC and KBI modules - Port B is 8 bits: PTB0-PTB7; shared with ADC module - Port C is only 7 bits: PTC0-PTC6 - Port D is 8 bits: PTD0-PTD7; shared with SPI, TIM1, and TIM2 modules - Port E is only 6 bits: PTE0-PTE5; shared with ESCI module Specific features in 64-pin QFP are: - Port A is 8 bits: PTA0-PTA7; shared with ADC and KBI modules - Port B is 8 bits: PTB0-PTB7; shared with ADC module - Port C is only 7 bits: PTC0-PTC6 - Port D is 8 bits: PTD0-PTD7; shared with SPI, TIM1, andTIM2 modules - Port E is only 6 bits: PTE0-PTE5; shared with ESCI module - Port F is 8 bits: PTF0-PTF7; shared with TIM2 module - Port G is 8 bits; PTG0-PTG7; shared with ADC module 1.2.2 Features of the CPU08 Features of the CPU08 include: * Enhanced HC05 programming model * Extensive loop control functions * 16 addressing modes (eight more than the HC05) * 16-bit index register and stack pointer * Memory-to-memory data transfers * Fast 8 x 8 multiply instruction * Fast 16/8 divide instruction * Binary-coded decimal (BCD) instructions * Optimization for controller applications * Efficient C language support 1.3 MCU Block Diagram Figure 1-1 shows the structure of the MC68HC908GR60A. Refer to Appendix A MC68HC908GR48A and Appendix B MC68HC908GR32A. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 21 General Description INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 1-1. MC68HC908GR60A Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 22 Freescale Semiconductor Pin Assignments 1.4 Pin Assignments CGMXFC VSSA VDDA PTC1 PTC0 PTA3/KBD3/AD11 30 29 28 27 26 25 1 OSC2 RST 31 32 OSC1 Figure 1-2, Figure 1-3, and Figure 1-4 illustrate the pin assignments for the 32-pin LQFP, 48-pin LQFP, and 64-pin QFP respectively. 24 PTA2/KBD2/AD10 PTD1/MISO 6 19 PTB5/AD5 PTD2/MOSI 7 18 PTB4/AD4 PTD3/SPSCK 8 17 PTB3/AD3 16 VDDAD/VREFH PTB2/AD2 20 15 5 PTB1/AD1 PTD0/SS/MCLK 14 VSSAD/VREFL PTB0/AD0 21 13 4 PTD6/T2CH0 IRQ 12 PTA0/KBD0/AD8 PTD5/T1CH1 22 11 3 PTD4/T1CH0 PTE1/RxD 10 PTA1/KBD1/AD9 VDD 23 9 2 VSS PTE0/TxD Figure 1-2. 32-Pin LQFP Pin Assignments MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 23 37 PTA3/KBD3/AD11 PTA4/KBD4/AD12 PTA7/KBD7/AD15 41 38 PTC0 42 PTA5/KBD5/AD13 PTC1 43 39 VDDA 44 PTA6/KBD6/AD14 VSSA 45 40 CGMXFC RST 1 46 OSC2 47 48 OSC1 General Description 36 PTA2/KBD2/AD10 PTE5 7 30 VDDAD/VREFH IRQ 8 29 PTB7/AD7 PTD0/SS/MCLK 9 28 PTB6/AD6 PTD1/MISO 10 27 PTB5/AD5 PTD2/MOSI 11 26 PTB4/AD4 25 PTB3/AD3 PTB2/AD2 24 VSS 13 PTD3/SPSCK 12 23 VSSAD/VREFL PTB1/AD1 31 22 6 PTB0/AD0 PTE4 21 PTC5 PTC4 32 20 5 PTC3 PTE3 19 PTC6 PTC2 33 18 4 PTD7/T2CH1 PTE2 17 PTA0/KBD0/AD8 PTD6/T2CH0 34 16 3 PTD5/T1CH1 PTE1/RxD 15 PTA1/KBD1/AD9 PTD4/T1CH0 35 14 2 VDD PTE0/TxD Figure 1-3. 48-Pin LQFP Pin Assignments MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 24 Freescale Semiconductor CGMXFC VSSA VDDA PTC1 PTC0 PTG7/AD23 PTG6/AD22 PTG5/AD21 PTG4/AD20 PTA7/KBD7/AD15 PTA6/KBD6/AD14 PTA5/KBD5/AD13 PTA4/KBD4/AD12 63 62 61 60 59 58 57 56 55 54 53 52 51 50 64 RST PTA3/KBD3/AD11 OSC2 OSC1 Pin Functions 49 48 PTA2/KBD2/AD10 1 PTE0/TxD 2 47 PTA1/KBD1/AD9 PTE1/RxD 3 46 PTA0/KBD0/AD8 PTE2 4 45 PTC6 PTE3 5 44 PTC5 PTE4 6 43 PTG3/AD19 PTE5 7 42 PTG2/AD18 PTF0 8 41 PTG1/AD17 PTF1 9 40 PTG0/AD16 PTF2 10 39 VSSAD/VREFL PTF3 11 38 VDDAD/VREFH IRQ 12 37 PTB7/AD7 PTD0/SS/MCLK 13 36 PTB6/AD6 PTD1/MISO 14 35 PTB5/AD5 PTD2/MOSI 15 34 PTB4/AD4 PTD3/SPSCK 16 33 PTB3/AD3 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4 PTC3 PTC2 PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTD7/T2CH1 PTD6/T2CH0 PTD5/T1CH1 PTD4/T1CH0 32 VDD VSS 17 Figure 1-4. 64-Pin QFP Pin Assignments 1.5 Pin Functions Descriptions of the pin functions are provided here. 1.5.1 Power Supply Pins (VDD and VSS) VDD and VSS are the power supply and ground pins. The MCU operates from a single power supply. Fast signal transitions on MCU pins place high, short-duration current demands on the power supply. To prevent noise problems, take special care to provide power supply bypassing at the MCU as Figure 1-5 shows. Place the C1 bypass capacitor as close to the MCU as possible. Use a high-frequency-response ceramic capacitor for C1. C2 is an optional bulk current bypass capacitor for use in applications that require the port pins to source high current levels. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 25 General Description MCU VSS VDD C1 0.1 F + C2 VDD Note: Component values shown represent typical applications. Figure 1-5. Power Supply Bypassing 1.5.2 Oscillator Pins (OSC1 and OSC2) OSC1 and OSC2 are the connections for an external crystal, resonator, or clock circuit. See Chapter 4 Clock Generator Module (CGM). 1.5.3 External Reset Pin (RST) A low on the RST pin forces the MCU to a known startup state. RST is bidirectional, allowing a reset of the entire system. It is driven low when any internal reset source is asserted. This pin contains an internal pullup resistor. See Chapter 14 System Integration Module (SIM). 1.5.4 External Interrupt Pin (IRQ) IRQ is an asynchronous external interrupt pin. This pin contains an internal pullup resistor. See Chapter 8 External Interrupt (IRQ). 1.5.5 CGM Power Supply Pins (VDDA and VSSA) VDDA and VSSA are the power supply pins for the analog portion of the clock generator module (CGM). Decoupling of these pins should be as per the digital supply. See Chapter 4 Clock Generator Module (CGM). 1.5.6 External Filter Capacitor Pin (CGMXFC) CGMXFC is an external filter capacitor connection for the CGM. See Chapter 4 Clock Generator Module (CGM). 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL) VDDAD and VSSAD are the power supply pins to the analog-to-digital converter (ADC). VREFH and VREFL are the reference voltage pins for the ADC. VREFH is the high reference supply for the ADC, and by default the VDDAD/VREFH pin should be externally filtered and connected to the same voltage potential as VDD. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 26 Freescale Semiconductor Pin Functions VREFL is the low reference supply for the ADC, and by default the VSSAD/VREFL pin should be connected to the same voltage potential as VSS. See Chapter 3 Analog-to-Digital Converter (ADC). 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8) PTA7-PTA0 are general-purpose, bidirectional I/O port pins. Any or all of the port A pins can be programmed to serve as keyboard interrupt pins or used as analog-to-digital inputs. PTA7-PTA4 are only available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 12 Input/Output (I/O) Ports, Chapter 9 Keyboard Interrupt Module (KBI), and Chapter 3 Analog-to-Digital Converter (ADC). These port pins also have selectable pullups when configured for input mode. The pullups are disengaged when configured for output mode. The pullups are selectable on an individual port bit basis. 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0) PTB7-PTB0 are general-purpose, bidirectional I/O port pins that can also be used for analog-to-digital converter (ADC) inputs. PTB7-PTB6 are only available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 12 Input/Output (I/O) Ports and Chapter 3 Analog-to-Digital Converter (ADC). 1.5.10 Port C I/O Pins (PTC6-PTC0) PTC6 and PTC5 are general-purpose, bidirectional I/O port pins. PTC4-PTC0 are general-purpose, bidirectional I/O port pins that contain higher current sink/source capability. PTC6-PTC2 are only available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 12 Input/Output (I/O) Ports. These port pins also have selectable pullups when configured for input mode. The pullups are disengaged when configured for output mode. The pullups are selectable on an individual port bit basis. 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS) PTD7-PTD0 are special-function, bidirectional I/O port pins. PTD3-PTD0 can be programmed to be serial peripheral interface (SPI) pins, while PTD7-PTD4 can be individually programmed to be timer interface module (TIM1 and TIM2) pins. PTD0 can be used to output a clock, MCLK. PTD7 is only available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 17 Timer Interface Module (TIM1), Chapter 18 Timer Interface Module (TIM2), Chapter 15 Serial Peripheral Interface (SPI) Module, Chapter 12 Input/Output (I/O) Ports, and Chapter 5 Configuration Register (CONFIG). These port pins also have selectable pullups when configured for input mode. The pullups are disengaged when configured for output mode. The pullups are selectable on an individual port bit basis. 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD) PTE5-PTE0 are general-purpose, bidirectional I/O port pins. PTE1 and PTE0 can also be programmed to be enhanced serial communications interface (ESCI) pins. PTE5-PTE2 are only available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 13 Enhanced Serial Communications Interface (ESCI) Module and Chapter 12 Input/Output (I/O) Ports. 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0) PTF7-PTF4 are special-function, bidirectional I/O port pins that can be individually programmed to be timer interface module (TIM2) pins. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 27 General Description PTF3-PTF0 are general-purpose, bidirectional I/O port pins that contain higher current sink/source capability. PTF7-PTF0 are only available on the 64-pin QFP package. See Chapter 17 Timer Interface Module (TIM1), Chapter 18 Timer Interface Module (TIM2), and Chapter 12 Input/Output (I/O) Ports. 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16) PTG7-PTG0 are general-purpose, bidirectional I/O port pins that can also be used for analog-to-digital converter (ADC) inputs. PTG7-PTG0 are only available on the 64-pin QFP package. See Chapter 12 Input/Output (I/O) Ports and Chapter 3 Analog-to-Digital Converter (ADC). 1.5.15 Unused Pin Termination Input pins and I/O port pins that are not used in the application must be terminated. This prevents excess current caused by floating inputs, and enhances immunity during noise or transient events. Termination methods include: 1. Configuring unused pins as outputs and driving high or low; 2. Configuring unused pins as inputs and enabling internal pull-ups; 3. Configuring unused pins as inputs and using external pull-up or pull-down resistors. Never connect unused pins directly to VDD or VSS. Since some general-purpose I/O pins are not available on all packages, these pins must be terminated as well. Either method 1 or 2 above are appropriate. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 28 Freescale Semiconductor Chapter 2 Memory 2.1 Introduction The CPU08 can address 64 Kbytes of memory space. The memory map, shown in Figure 2-1, includes: * 62,078 bytes of user FLASH memory * 2048 bytes of random-access memory (RAM) * 52 bytes of user-defined vectors 2.2 Unimplemented Memory Locations Accessing an unimplemented location can cause an illegal address reset. In the memory map (Figure 2-1) and in register figures in this document, unimplemented locations are shaded. 2.3 Reserved Memory Locations Accessing a reserved location can have unpredictable effects on microcontroller (MCU) operation. In the Figure 2-1 and in register figures in this document, reserved locations are marked with the word Reserved or with the letter R. 2.4 Input/Output (I/O) Section Most of the control, status, and data registers are in the zero page area of $0000-$003F, or at $0440-$0461. Additional I/O registers have these addresses: * $FE00; SIM break status register, BSR * $FE01; SIM reset status register, SRSR * $FE02; reserved * $FE03; SIM break flag control register, BFCR * $FE04; interrupt status register 1, INT1 * $FE05; interrupt status register 2, INT2 * $FE06; interrupt status register 3, INT3 * $FE07; interrupt status register 4, INT4 * $FE08; FLASH-2 control register, FL2CR * $FE09; break address register high, BRKH * $FE0A; break address register low, BRKL * $FE0B; break status and control register, BRKSCR * $FE0C; LVI status register, LVISR * $FE0D; FLASH-2 test control register, FLTCR2 * $FE0E; FLASH-1 test control register, FLTCR1 * $FF80; FLASH-1 block protect register, FL1BPR * $FF81; FLASH-2 block protect register, FL2BPR * $FF88; FLASH-1 control register, FL1CR Data registers are shown in Figure 2-2. Table 2-1 is a list of vector locations. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 29 Memory $0000 $003F I/O REGISTERS 64 BYTES $0040 $043F RAM-1 1024 BYTES $0440 $0461 I/O REGISTERS 34 BYTES $0462 $04FF FLASH-2 158 BYTES $0500 $057F RESERVED 128 BYTES $FE00 SIM BREAK STATUS REGISTER (BSR) $FE01 SIM RESET STATUS REGISTER (SRSR) $FE02 RESERVED $FE03 SIM BREAK FLAG CONTROL REGISTER (BFCR) $FE04 INTERRUPT STATUS REGISTER 1 (INT1) $FE05 INTERRUPT STATUS REGISTER 2 (INT2) $FE06 INTERRUPT STATUS REGISTER 3 (INT3) $FE07 INTERRUPT STATUS REGISTER 4 (INT4) $FE08 FLASH-2 CONTROL REGISTER (FL2CR) $FE09 BREAK ADDRESS REGISTER HIGH (BRKH) $FE0A BREAK ADDRESS REGISTER LOW (BRKL) $FE0B BREAK STATUS AND CONTROL REGISTER (BRKSCR) $FE0C LVI STATUS REGISTER (LVISR) $FE0D FLASH-2 TEST CONTROL REGISTER (FLTCR2) $FE0E FLASH-1 TEST CONTROL REGISTER (FLTCR1) $FE0F UNIMPLEMENTED $FE10 $FE1F UNIMPLEMENTED 16 BYTES RESERVED FOR COMPATIBILITY WITH MONITOR CODE FOR A-FAMILY PART $FE20 $FF7F MONITOR ROM 352 BYTES $FF80 FLASH-1 BLOCK PROTECT REGISTER (FL1BPR) $FF81 FLASH-2 BLOCK PROTECT REGISTER (FL2BPR) $FF82 $FF87 RESERVED 6 BYTES $FF88 FLASH-1 CONTROL REGISTER (FL1CR) $0580 $097F RAM-2 1024 BYTES $0980 $1B7F FLASH-2 4608 BYTES $1B80 $1DFF RESERVED 640 BYTES $1E00 $1E0F MONITOR ROM 16 BYTES $1E10 $1E1F RESERVED 16 BYTES $1E20 $7FFF FLASH-2 25,056 BYTES $FF89 $FFCB RESERVED 67 BYTES $8000 $FDFF FLASH-1 32,256 BYTES $FFCC $FFFF(1) FLASH-1 VECTORS 52 BYTES 1. $FFF6-$FFFD used for eight security bytes Figure 2-1. MC68HC908GR60A Memory Map MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 30 Freescale Semiconductor Input/Output (I/O) Section Addr. $0000 Register Name Port A Data Register Read: (PTA) Write: See page 135. Reset: $0001 Port B Data Register Read: (PTB) Write: See page 138. Reset: $0002 Port C Data Register Read: (PTC) Write: See page 140. Reset: $0003 $0004 Port D Data Register Read: (PTD) Write: See page 142. Reset: Data Direction Register A Read: (DDRA) Write: See page 136. Reset: $0005 Data Direction Register B Read: (DDRB) Write: See page 138. Reset: $0006 Data Direction Register C Read: (DDRC) Write: See page 140. Reset: $0007 $0008 Data Direction Register D Read: (DDRD) Write: See page 143. Reset: Port E Data Register Read: (PTE) Write: See page 145. Reset: $0009 ESCI Prescaler Register Read: (SCPSC) Write: See page 175. Reset: $000A ESCI Arbiter Control Read: Register (SCIACTL) Write: See page 179. Reset: $000B ESCI Arbiter Data Read: Register (SCIADAT) Write: See page 180. Reset: Bit 7 6 5 4 3 2 1 Bit 0 PTA7 PTA6 PTA5 PTA4 PTA3 PTA2 PTA1 PTA0 PTB2 PTB1 PTB0 PTC2 PTC1 PTC0 PTD2 PTD1 PTD0 Unaffected by reset PTB7 PTB6 PTB5 PTB4 PTB3 Unaffected by reset 1 PTC6 PTC5 PTC4 PTC3 Unaffected by reset PTD7 PTD6 PTD5 PTD4 PTD3 Unaffected by reset DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 0 0 PTE5 PTE4 PTE3 PTE2 PTE1 PTE0 PSSB2 PSSB1 PSSB0 0 Unaffected by reset PDS2 0 AM1 PDS1 PDS0 PSSB4 0 0 0 ALOST AM0 ACLK PSSB3 0 0 0 0 AFIN ARUN AROVFL ARD8 0 0 0 0 0 0 0 0 ARD7 ARD6 ARD5 ARD4 ARD3 ARD2 ARD1 ARD0 0 0 0 0 0 0 0 0 = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 31 Memory Addr. $000C $000D $000E $000F $0010 $0011 $0012 Register Name Data Direction Register E Read: (DDRE) Write: See page 146. Reset: Port C Input Pullup Enable Read: Register (PTCPUE) Write: See page 142. Reset: SPI Control Register Read: (SPCR) Write: See page 217. Reset: SPI Status and Control Read: Register (SPSCR) Write: See page 218. Reset: SPI Data Register Read: (SPDR) Write: See page 220. Reset: $0014 ESCI Control Register 2 Read: (SCC2) Write: See page 168. Reset: $0017 0 5 4 3 2 1 Bit 0 DDRE5 DDRE4 DDRE3 DDRE2 DDRE1 DDRE0 0 0 0 0 0 0 0 0 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0 0 0 0 0 0 0 0 PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0 0 0 0 0 0 0 0 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0 0 0 0 0 0 0 0 SPRIE R SPMSTR CPOL CPHA SPWOM SPE SPTIE 0 0 1 0 1 0 0 0 OVRF MODF SPTE MODFEN SPR1 SPR0 0 0 Port D Input Pullup Enable Read: PTDPUE7 Register (PTDPUE) Write: See page 145. Reset: 0 $0013 $0016 6 0 Port A Input Pullup Enable Read: PTAPUE7 Register (PTAPUE) Write: See page 137. Reset: 0 ESCI Control Register 1 Read: (SCC1) Write: See page 166. Reset: $0015 Bit 7 SPRF ERRIE 0 0 0 0 1 0 0 0 R7 R6 R5 R4 R3 R2 R1 R0 T7 T6 T5 T4 T3 T2 T1 T0 Unaffected by reset LOOPS ENSCI TXINV M WAKE ILTY PEN PTY 0 0 0 0 0 0 0 0 SCTIE TCIE SCRIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 T8 R R ORIE NEIE FEIE PEIE ESCI Control Register 3 Read: (SCC3) Write: See page 169. Reset: R8 U 0 0 0 0 0 0 0 ESCI Status Register 1 Read: (SCS1) Write: See page 170. Reset: SCTE TC SCRF IDLE OR NF FE PE 1 1 0 0 0 0 0 0 ESCI Status Register 2 Read: (SCS2) Write: See page 173. Reset: 0 0 0 0 0 0 BKF RPF 0 0 0 0 0 0 0 0 = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 32 Freescale Semiconductor Input/Output (I/O) Section Addr. $0018 $0019 Register Name ESCI Data Register Read: (SCDR) Write: See page 173. Reset: ESCI Baud Rate Register Read: (SCBR) Write: See page 174. Reset: Keyboard Status and Control Read: $001A Register (INTKBSCR) Write: See page 118. Reset: $001B Keyboard Interrupt Enable Read: Register (INTKBIER) Write: See page 119. Reset: $001C Timebase Module Control Read: Register (TBCR) Write: See page 224. Reset: $001D $001E $001F IRQ Status and Control Read: Register (INTSCR) Write: See page 112. Reset: Configuration Register 2 Read: (CONFIG2)(1) Write: See page 90. Reset: Configuration Register 1 Read: (CONFIG1)(1) Write: See page 91. Reset: Bit 7 6 5 4 3 2 1 Bit 0 R7 R6 R5 R4 R3 R2 R1 R0 T7 T6 T5 T4 T3 T2 T1 T0 Unaffected by reset LINT LINR SCP1 SCP0 R SCR2 SCR1 SCR0 0 0 0 0 0 0 0 0 0 0 0 0 KEYF 0 IMASKK MODEK ACKK 0 0 0 0 0 0 0 0 KBIE7 KBIE6 KBIE5 KBIE4 KBIE3 KBIE2 KBIE1 KBIE0 0 0 0 0 0 0 0 0 TBIE TBON R 0 0 0 IMASK MODE 0 0 TBIF 0 TBR2 TBR1 TBR0 0 0 0 0 0 0 0 0 0 IRQF TACK 0 ACK 0 0 0 0 0 MCLKSEL MCLK1 MCLK0 R 0 0 0 0 0 0 0 1 COPRS LVISTOP LVIRSTD LVIPWRD LVI5OR3 SSREC STOP COPD 0 0 0 0 0 0 0 0 0 0 TMBCLK- OSCENINSCIBDSRC SEL STOP 1. One-time writable register after each reset, except LVI5OR3 bit. LVI5OR3 bit is only reset via POR (power-on reset). $0020 $0021 $0022 $0023 TIM1 Status and Control Read: Register (T1SC) Write: See page 234. Reset: TOF 0 TOIE TSTOP 0 0 1 0 TIM1 Counter Read: Register High (T1CNTH) Write: See page 235. Reset: Bit 15 14 13 0 0 TIM1 Counter Read: Register Low (T1CNTL) Write: See page 235. Reset: Bit 7 TIM1 Counter Modulo Read: Register High (T1MODH) Write: See page 236. Reset: 0 PS2 PS1 PS0 0 0 0 0 12 11 10 9 Bit 8 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 1 1 1 1 1 1 1 0 1 = Unimplemented TRST R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 33 Memory Addr. $0024 $0025 $0026 Register Name TIM1 Counter Modulo Read: Register Low (T1MODL) Write: See page 236. Reset: TIM1 Channel 0 Status and Read: Control Register (T1SC0) Write: See page 237. Reset: TIM1 Channel 0 Read: Register High (T1CH0H) Write: See page 240. Reset: $0027 TIM1 Channel 0 Read: Register Low (T1CH0L) Write: See page 240. Reset: $0028 TIM1 Channel 1 Status and Read: Control Register (T1SC1) Write: See page 237. Reset: $0029 $002A TIM1 Channel 1 Read: Register High (T1CH1H) Write: See page 240. Reset: TIM1 Channel 1 Read: Register Low (T1CH1L) Write: See page 240. Reset: Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 1 1 1 1 1 1 1 1 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 CH0F 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH1F 0 0 CH1IE MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 PS2 PS1 PS0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset TOF $002B TIM2 Status and Control Read: Register (T2SC) Write: See page 237. Reset: 0 0 1 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 $002C TIM2 Counter Read: Register High (T2CNTH) Write: See page 235. Reset: 0 0 0 0 0 0 0 0 TIM2 Counter Read: Register Low (T2CNTL) Write: See page 235. Reset: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 1 1 1 1 1 1 1 $002D $002E $002F TIM2 Counter Modulo Read: Register High (T2MODH) Write: See page 236. Reset: TIM2 Counter Modulo Read: Register Low (T2MODL) Write: See page 236. Reset: 0 1 TOIE TSTOP = Unimplemented 0 0 TRST R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 34 Freescale Semiconductor Input/Output (I/O) Section Addr. $0030 $0031 $0032 Register Name Bit 7 TIM2 Channel 0 Status and Read: Control Register (T2SC0) Write: See page 237. Reset: TIM2 Channel 0 Read: Register High (T2CH0H) Write: See page 240. Reset: TIM2 Channel 0 Read: Register Low (T2CH0L) Write: See page 240. Reset: $0033 TIM2 Channel 1 Status and Read: Control Register (T2SC1) Write: See page 237. Reset: $0034 TIM2 Channel 1 Read: Register High (T2CH1H) Write: See page 240. Reset: $0035 $0036 TIM2 Channel 1 Read: Register Low (T2CH1L) Write: See page 240. Reset: PLL Control Register Read: (PCTL) Write: See page 81. Reset: $0037 PLL Bandwidth Control Read: Register (PBWC) Write: See page 82. Reset: $0038 PLL Multiplier Select High Read: Register (PMSH) Write: See page 83. Reset: $0039 $003A PLL Multiplier Select Low Read: Register (PMSL) Write: See page 84. Reset: PLL VCO Select Range Read: Register (PMRS) Write: See page 84. Reset: Read: $003B 6 5 4 3 2 1 Bit 0 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 CH0F 0 Indeterminate after reset Bit 7 6 5 4 Indeterminate after reset CH1F 0 0 CH1IE MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset PLLIE 0 AUTO PLLF PLLON BCS R R VPR1 VPR0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 MUL11 MUL10 MUL9 MUL8 0 LOCK ACQ R 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MUL7 MUL6 MUL5 MUL4 MUL3 MUL2 MUL1 MUL0 0 1 0 0 U U U U VRS7 VRS6 VRS5 VRS4 VRS3 VRS2 VRS1 VRS0 0 1 0 0 0 0 0 0 0 0 0 0 R R R R 0 0 0 0 1 Reserved Write: Reset: 3 0 = Unimplemented 0 R = Reserved 0 U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 35 Memory Addr. $003C $003D $003E Register Name 6 5 4 3 2 1 Bit 0 AIEN ADCO ADCH4 ADCH3 ADCH2 ADCH1 ADCH0 0 0 0 1 1 1 1 1 ADC Data High Register Read: (ADRH) Write: See page 67. Reset: 0 0 0 0 0 0 AD9 AD8 ADC Data Low Register Read: (ADRL) Write: See page 67. Reset: AD7 AD2 AD1 AD0 COCO $003F ADC Clock Register Read: (ADCLK) Write: See page 69. Reset: $0440 Port F Data Register Read: (PTF) Write: See page 147. Reset: $0441 $0444 Port G Data Register Read: (PTG) Write: See page 149. Reset: Data Direction Register F Read: (DDRF) Write: See page 148. Reset: $0445 Data Direction Register G Read: (DDRG) Write: See page 150. Reset: $0448 Keyboard Interrupt Read: Polarity Register Write: (INTKBIPR) See page 119. Reset: $0456 $0457 $0458 Bit 7 ADC Status and Control Read: Register (ADSCR) Write: See page 65. Reset: TIM2 Channel 2 Status and Read: Control Register (T2SC2) Write: See page 255. Reset: TIM2 Channel 2 Read: Register High (T2CH2H) Write: See page 258. Reset: TIM2 Channel 2 Read: Register Low (T2CH2L) Write: See page 258. Reset: R Unaffected by reset AD6 AD5 AD4 A3 Unaffected by reset 0 ADIV2 ADIV1 ADIV0 ADICLK MODE1 MODE0 R 0 0 0 0 0 1 0 0 PTF7 PTF6 PTF5 PTF4 PTAF3 PTF2 PTF1 PTF0 PTG2 PTG1 PTG0 Unaffected by reset PTG7 PTG6 PTG5 PTG4 PTG3 Unaffected by reset DDRF7 DDRF6 DDRF5 DDRF4 DDRF3 DDRF2 DDRF1 DDRF0 0 0 0 0 0 0 0 0 DDRG7 DDRG6 DDRG5 DDRG4 DDRG3 DDRG2 DDRG1 DDRG0 0 0 0 0 0 0 0 0 KBIP7 KBIP6 KBIP5 KBIP4 KBIP3 KBIP2 KBIP1 KBIP0 0 0 0 0 0 0 0 0 CH2IE MS2B MS2A ELS2B ELS2A TOV2 CH2MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 CH2F 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 36 Freescale Semiconductor Input/Output (I/O) Section Addr. $0459 $045A $045B Register Name Bit 7 TIM2 Channel 3 Status and Read: Control Register (T2SC3) Write: See page 255. Reset: TIM2 Channel 3 Read: Register High (T2CH3H) Write: See page 258. Reset: TIM2 Channel 3 Read: Register Low (T2CH3L) Write: See page 258. Reset: $045C TIM2 Channel 4 Status and Read: Control Register (T2SC4) Write: See page 255. Reset: $045D TIM2 Channel 4 Read: Register High (T2CH4H) Write: See page 258. Reset: $045E $045F TIM2 Channel 4 Read: Register Low (T2CH4L) Write: See page 258. Reset: TIM2 Channel 5 Status and Read: Control Register (T2SC5) Write: See page 255. Reset: $0460 TIM2 Channel 5 Read: Register High (T2CH5H) Write: See page 258. Reset: $0461 TIM2 Channel 5 Read: Register Low (T2CH5L) Write: See page 258. Reset: $FE00 Break Status Register Read: (BSR) Write: See page 199. Reset: CH3F 0 6 5 0 CH3IE 4 3 2 1 Bit 0 MS3A ELS3B ELS3A TOV3 CH3MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH4F CH4IE MS4B MS4A ELS4B ELS4A TOV4 CH4MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH5F 0 0 CH5IE MS5A ELS5B ELS5A TOV 5 CH5MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset SBSW R R R R R R 0 0 0 0 0 0 0 0 POR PIN COP ILOP ILAD MODRST LVI 0 1 0 0 0 0 0 0 0 R R R R R R R R 0 0 0 0 0 0 0 0 NOTE 1 R 1. Writing a 0 clears SBSW. $FE01 SIM Reset Status Register Read: (SRSR) Write: See page 199. POR: Read: $FE02 Reserved Write: Reset: = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 7 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 37 Memory Addr. Bit 7 6 5 4 3 2 1 Bit 0 BCFE R R R R R R R 0 0 0 0 0 0 0 0 Interrupt Status Register 1 Read: (INT1) Write: See page 195. Reset: IF6 IF5 IF4 IF3 IF2 IF1 0 0 R R R R R R R R 0 0 0 0 0 0 0 0 Interrupt Status Register 2 Read: (INT2) Write: See page 195. Reset: IF14 IF13 IF12 IF11 IF10 IF9 IF8 IF7 R R R R R R R R 0 0 0 0 0 0 0 0 IF22 IF21 IF20 IF19 IF18 IF17 IF16 IF15 $FE06 Interrupt Status Register 3 Read: (INT3) Write: See page 195. Reset: R R R R R R R R 0 0 0 0 0 0 0 0 0 0 0 0 0 0 IF24 IF23 $FE07 Interrupt Status Register 4 Read: (INT4) Write: See page 196. Reset: R R R R R R R R 0 0 0 0 0 0 0 0 0 0 0 0 HVEN MASS ERASE PGM 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $FE03 $FE04 $FE05 $FE08 Register Name Break Flag Control Register Read: (BFCR) Write: See page 200. Reset: FLASH-2 Control Register Read: (FL2CR) Write: See page 50. Reset: Break Address Register High Read: $FE09 (BRKH) Write: See page 265. Reset: Break Address Register Low Read: $FE0A (BRKL) Write: See page 265. Reset: $FE0B $FE0C $FE0D $FE0E Break Status and Control Read: Register (BRKSCR) Write: See page 265. Reset: LVI Status Register Read: (LVISR) Write: See page 129. Reset: Read: FLASH-2 Test Control Write: Register (FLTCR2) Reset: Read: FLASH-1 Test Control Write: Register (FLTCR1) Reset: BRKE BRKA 0 0 0 0 0 0 0 0 LVIOUT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R R R R R R R R 0 0 0 0 0 0 0 0 R R R R R R R R 0 0 0 0 0 0 0 0 = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 8 of 9) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 38 Freescale Semiconductor Input/Output (I/O) Section Addr. Register Name $FF80 FLASH-1 Block Protect Read: Register (FL1BPR)(1) Write: See page 43. Reset: $FF81 FLASH-2 Block Protect Read: Register (FL2BPR)(1) Write: See page 51. Reset: Bit 7 6 5 4 3 2 1 Bit 0 BPR7 BPR6 BPR5 BPR4 BPR3 BPR2 BPR1 BPR0 BPR2 BPR1 BPR0 HVEN MASS ERASE PGM 0 0 0 0 Unaffected by reset BPR7 BPR6 BPR5 BPR4 BPR3 Unaffected by reset 1. Non-volatile FLASH register $FF88 $FFFF FLASH-1 Control Register Read: (FL1CR) Write: See page 42. Reset: 0 0 0 0 0 0 0 0 COP Control Register Read: (COPCTL) Write: See page 95. Reset: Low byte of reset vector Writing clears COP counter (any value) Unaffected by reset = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 9 of 9) . Table 2-1. Vector Addresses Vector Priority Lowest Vector Address Vector $FFCC TIM2 Channel 5 Vector (High) $FFCD TIM2 Channel 5 Vector (Low) $FFCE TIM2 Channel 4 Vector (High) $FFCF TIM2 Channel 4 Vector (Low) $FFD0 TIM2 Channel 3 Vector (High) $FFD1 TIM2 Channel 3 Vector (Low) $FFD2 TIM2 Channel 2 Vector (High) $FFD3 TIM2 Channel 2 Vector (Low) $FFD4 $FFDB Reserved $FFDC Timebase Vector (High) $FFDD Timebase Vector (Low) $FFDE ADC Conversion Complete Vector (High) $FFDF ADC Conversion Complete Vector (Low) IF24 IF23 IF22 IF21 IF20 IF17 IF16 IF15 Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 39 Memory Table 2-1. Vector Addresses (Continued) Vector Priority Vector Address Vector $FFE0 Keyboard Vector (High) $FFE1 Keyboard Vector (Low) $FFE2 ESCI Transmit Vector (High) $FFE3 ESCI Transmit Vector (Low) $FFE4 ESCI Receive Vector (High) $FFE5 ESCI Receive Vector (Low) $FFE6 ESCI Error Vector (High) $FFE7 ESCI Error Vector (Low) $FFE8 SPI Transmit Vector (High) $FFE9 SPI Transmit Vector (Low) $FFEA SPI Receive Vector (High) $FFEB SPI Receive Vector (Low) $FFEC TIM2 Overflow Vector (High) $FFED TIM2 Overflow Vector (Low) $FFEE TIM2 Channel 1 Vector (High) $FFEF TIM2 Channel 1 Vector (Low) $FFF0 TIM2 Channel 0 Vector (High) $FFF1 TIM2 Channel 0 Vector (Low) $FFF2 TIM1 Overflow Vector (High) $FFF3 TIM1 Overflow Vector (Low) $FFF4 TIM1 Channel 1 Vector (High) $FFF5 TIM1 Channel 1 Vector (Low) $FFF6 TIM1 Channel 0 Vector (High) $FFF7 TIM1 Channel 0 Vector (Low) $FFF8 PLL Vector (High) $FFF9 PLL Vector (Low) $FFFA IRQ Vector (High) $FFFB IRQ Vector (Low) $FFFC SWI Vector (High) $FFFD SWI Vector (Low) $FFFE Reset Vector (High) $FFFF Reset Vector (Low) IF14 IF13 IF12 IF11 IF10 IF9 IF8 IF7 IF6 IF5 IF4 IF3 IF2 IF1 -- Highest -- MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 40 Freescale Semiconductor Random-Access Memory (RAM) 2.5 Random-Access Memory (RAM) The RAM locations are broken into two non-continuous memory blocks. The RAM addresses locations are $0040-$043F and $0580-$097F. The location of the stack RAM is programmable. The 16-bit stack pointer allows the stack to be anywhere in the 64-Kbyte memory space. NOTE For correct operation, the stack pointer must point only to RAM locations. Within page zero are 192 bytes of RAM. Because the location of the stack RAM is programmable, all page zero RAM locations can be used for I/O control and user data or code. When the stack pointer is moved from its reset location at $00FF out of page zero, direct addressing mode instructions can efficiently access all page zero RAM locations. Page zero RAM, therefore, provides ideal locations for frequently accessed global variables. Before processing an interrupt, the CPU uses five bytes of the stack to save the contents of the CPU registers. NOTE For M6805 compatibility, the H register is not stacked. During a subroutine call, the CPU uses two bytes of the stack to store the return address. The stack pointer decrements during pushes and increments during pulls. NOTE Be careful when using nested subroutines. The CPU may overwrite data in the RAM during a subroutine or during the interrupt stacking operation. 2.6 FLASH-1 Memory (FLASH-1) This subsection describes the operation of the embedded FLASH-1 memory. This memory can be read, programmed, and erased from a single external supply. The program and erase operations are enabled through the use of an internal charge pump. 2.6.1 Functional Description The FLASH-1 memory is an array of 32,256 bytes with two bytes of block protection (one byte for protecting areas within FLASH-1 array and one byte for protecting areas within FLASH-2 array) and an additional 52 bytes of user vectors. An erased bit reads as a 1 and a programmed bit reads as a 0. Memory in the FLASH-1 array is organized into rows within pages. There are two rows of memory per page with 64 bytes per row. The minimum erase block size is a single page,128 bytes. Programming is performed on a per-row basis, 64 bytes at a time. Program and erase operations are facilitated through control bits in the FLASH-1 control register (FL1CR). Details for these operations appear later in this subsection. The FLASH-1 memory map consists of: * $8000-$FDFF: user memory (32,256 bytes) * $FF80: FLASH-1 block protect register (FL1BPR) * $FF81: FLASH-2 block protect register (FL2BPR) * $FF88: FLASH-1 control register (FL1CR) * $FFCC-$FFFF: these locations are reserved for user-defined interrupt and reset vectors (see Table 2-1 for details) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 41 Memory Programming tools are available from Freescale Semiconductor. Contact your local representative for more information. NOTE A security feature prevents viewing of the FLASH contents.(1) 2.6.2 FLASH-1 Control and Block Protect Registers The FLASH-1 array has two registers that control its operation, the FLASH-1 control register (FL1CR) and the FLASH-1 block protect register (FL1BPR). 2.6.2.1 FLASH-1 Control Register The FLASH-1 control register (FL1CR) controls FLASH program and erase operations. Address: Read: $FE08 Bit 7 6 5 4 0 0 0 0 0 0 0 0 Write: Reset: 3 2 1 Bit 0 HVEN MASS ERASE PGM 0 0 0 0 = Unimplemented Figure 2-3. FLASH-1 Control Register (FL1CR) HVEN -- High-Voltage Enable Bit This read/write bit enables the charge pump to drive high voltages for program and erase operations in the array. HVEN can only be set if either PGM = 1 or ERASE = 1 and the proper sequence for program or erase is followed. 1 = High voltage enabled to array and charge pump on 0 = High voltage disabled to array and charge pump off MASS -- Mass Erase Control Bit Setting this read/write bit configures the FLASH-1 array for mass erase operation. 1 = MASS erase operation selected 0 = MASS erase operation unselected ERASE -- Erase Control Bit This read/write bit configures the memory for erase operation. ERASE is interlocked with the PGM bit such that both bits cannot be equal to 1 or set to 1 at the same time. 1 = Erase operation selected 0 = Erase operation unselected PGM -- Program Control Bit This read/write bit configures the memory for program operation. PGM is interlocked with the ERASE bit such that both bits cannot be equal to 1 or set to 1 at the same time. 1 = Program operation selected 0 = Program operation unselected 1. No security feature is absolutely secure. However, Freescale's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 42 Freescale Semiconductor FLASH-1 Memory (FLASH-1) 2.6.2.2 FLASH-1 Block Protect Register The FLASH-1 block protect register (FL1BPR) is implemented as a byte within the FLASH-1 memory; therefore, it can only be written during a FLASH programming sequence. The value in this register determines the starting location of the protected range within the FLASH-1 memory. Address: $FF80 Read: Write: Bit 7 6 5 4 3 2 1 Bit 0 BPR7 BPR6 BPR5 BPR4 BPR3 BPR2 BPR1 BPR0 Unaffected by reset Figure 2-4. FLASH-1 Block Protect Register (FL1BPR) FL1BPR[7:0] -- Block Protect Register Bits 7 to 0 These eight bits represent bits [14:7] of a 16-bit memory address. Bit 15 is a 1 and bits [6:0] are 0s. The resultant 16-bit address is used for specifying the start address of the FLASH-1 memory for block protection. FLASH-1 is protected from this start address to the end of FLASH-1 memory at $FFFF. With this mechanism, the protect start address can be $XX00 and $XX80 (128 byte page boundaries) within the FLASH-1 array. 16-BIT MEMORY ADDRESS START ADDRESS OF FLASH BLOCK PROTECT 1 FLBPR VALUE 0 0 0 0 0 0 0 Figure 2-5. FLASH-1 Block Protect Start Address Table 2-2. FLASH-1 Protected Ranges FL1BPR[7:0] Protected Range $FF No protection $FE $FF00-$FFFF $FD $0B $FE80-$FFFF $8580-$FFFF $0A $8500-$FFFF $09 $8480-$FFFF $08 $04 $8400-$FFFF $8200-$FFFF $03 $8180-$FFFF $02 $8100-$FFFF $01 $8080-$FFFF $00 $8000-$FFFF MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 43 Memory Decreasing the value in FL1BPR by one increases the protected range by one page (128 bytes). However, programming the block protect register with $FE protects a range twice that size, 256 bytes, in the corresponding array. $FE means that locations $FF00-$FFFF are protected in FLASH-1. The FLASH memory does not exist at some locations. The block protection range configuration is unaffected if FLASH memory does not exist in that range. Refer to Figure 2-1 and make sure that the desired locations are protected. 2.6.3 FLASH-1 Block Protection Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target application, provision is made for protecting blocks of memory from unintentional erase or program operations due to system malfunction. This protection is done by using the FLASH-1 block protection register (FL1BPR). FL1BPR determines the range of the FLASH-1 memory which is to be protected. The range of the protected area starts from a location defined by FL1BPR and ends at the bottom of the FLASH-1 memory ($FFFF). When the memory is protected, the HVEN bit can not be set in either ERASE or PROGRAM operations. NOTE In performing a program or erase operation, the FLASH-1 block protect register must be read after setting the PGM or ERASE bit and before asserting the HVEN bit. When the FLASH-1 block protect register is programmed with all 0's, the entire memory is protected from being programmed and erased. When all the bits are erased (all 1's), the entire memory is accessible for program and erase. When bits within FL1BPR are programmed (0), they lock a block of memory address ranges as shown in Figure 2-4. If FL1BPR is programmed with any value other than $FF, the protected block of FLASH memory can not be erased or programmed. NOTE The vector locations and the FLASH block protect registers are located in the same page. FL1BPR and FL2BPR are not protected with special hardware or software. Therefore, if this page is not protected by FL1BPR and the vector locations are erased by either a page or a mass erase operation, then both FL1BPR and FL2BPR will also get erased. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 44 Freescale Semiconductor FLASH-1 Memory (FLASH-1) 2.6.4 FLASH-1 Mass Erase Operation Use this step-by-step procedure to erase the entire FLASH-1 memory: 1. Set both the ERASE bit and the MASS bit in the FLASH-1 control register (FL1CR). 2. Read the FLASH-1 block protect register (FL1BPR). NOTE Mass erase is disabled whenever any block is protected (FL1BPR does not equal $FF). 3. 4. 5. 6. 7. 8. 9. 10. Write to any FLASH-1 address within the FLASH-1 array with any data. Wait for a time, tNVS (minimum 10 s). Set the HVEN bit. Wait for a time, tMERASE (minimum 4 ms). Clear the ERASE and MASS bits. Wait for a time, tNVHL (minimum 100 s). Clear the HVEN bit. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 45 Memory 2.6.5 FLASH-1 Page Erase Operation Use this step-by-step procedure to erase a page (128 bytes) of FLASH-1 memory: 1. Set the ERASE bit and clear the MASS bit in the FLASH-1 control register (FL1CR). 2. Read the FLASH-1 block protect register (FL1BPR). 3. Write any data to any FLASH-1 address within the address range of the page (128 byte block) to be erased. 4. Wait for time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for time, tERASE (minimum 1 ms or 4 ms). 7. Clear the ERASE bit. 8. Wait for time, tNVH (minimum 5 s). 9. Clear the HVEN bit. 10. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. In applications that require more than 1000 program/erase cycles, use the 4 ms page erase specification to get improved long-term reliability. Any application can use this 4 ms page erase specification. However, in applications where a FLASH location will be erased and reprogrammed less than 1000 times, and speed is important, use the 1 ms page erase specification to get a shorter cycle time. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 46 Freescale Semiconductor FLASH-1 Memory (FLASH-1) 2.6.6 FLASH-1 Program Operation Programming of the FLASH-1 memory is done on a row basis. A row consists of 64 consecutive bytes with address ranges as follows: * $XX00 to $XX3F * $XX40 to $XX7F * $XX80 to $XXBF * $XXC0 to $XXFF During the programming cycle, make sure that all addresses being written to fit within one of the ranges specified above. Attempts to program addresses in different row ranges in one programming cycle will fail. Use this step-by-step procedure to program a row of FLASH-1 memory. NOTE Only bytes which are currently $FF may be programmed. 1. Set the PGM bit in the FLASH-1 control register (FL1CR). This configures the memory for program operation and enables the latching of address and data programming. 2. Read the FLASH-1 block protect register (FL1BPR). 3. Write to any FLASH-1 address within the row address range desired with any data. 4. Wait for time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for time, tPGS (minimum 5 s). 7. Write data byte to the FLASH-1 address to be programmed. 8. Wait for time, tPROG (minimum 30 s). 9. Repeat steps 7 and 8 until all the bytes within the row are programmed. 10. Clear the PGM bit. 11. Wait for time, tNVH (minimum 5 s) 12. Clear the HVEN bit. 13. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. The FLASH programming algorithm flowchart is shown in Figure 2-6. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. D. Do not exceed tPROG maximum or tHV maximum. tHV is defined as the cumulative high voltage programming time to the same row before next erase. tHV must satisfy this condition: tNVS+ tNVH + tPGS + (tPROG X 64) tHV maximum MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 47 Memory E. The time between each FLASH address change (step 7 to step 7), or the time between the last FLASH address programmed to clearing the PGM bit (step 7 to step 10) must not exceed the maximum programming time, tPROG maximum. F. Be cautious when programming the FLASH-1 array to ensure that non-FLASH locations are not used as the address that is written to when selecting either the desired row address range in step 3 of the algorithm or the byte to be programmed in step 7 of the algorithm. 2.6.7 Low-Power Modes The WAIT and STOP instructions will place the MCU in low power-consumption standby modes. 2.6.7.1 Wait Mode Putting the MCU into wait mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly; however, no memory activity will take place since the CPU is inactive. The WAIT instruction should not be executed while performing a program or erase operation on the FLASH. Wait mode will suspend any FLASH program/erase operations and leave the memory in a standby mode. 2.6.7.2 Stop Mode Putting the MCU into stop mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly; however, no memory activity will take place since the CPU is inactive. The STOP instruction should not be executed while performing a program or erase operation on the FLASH. Stop mode will suspend any FLASH program/erase operations and leave the memory in a standby mode. NOTE Standby mode is the power saving mode of the FLASH module, in which all internal control signals to the FLASH are inactive and the current consumption of the FLASH is minimum. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 48 Freescale Semiconductor FLASH-1 Memory (FLASH-1) Algorithm for programming a row (64 bytes) of FLASH memory 1 SET PGM BIT 2 READ THE FLASH BLOCK PROTECT REGISTER 3 WRITE ANY DATA TO ANY FLASH ADDRESS WITHIN THE ROW ADDRESS RANGE DESIRED 4 WAIT FOR A TIME, tNVS 5 SET HVEN BIT 6 WAIT FOR A TIME, tPGS 7 8 WRITE DATA TO THE FLASH ADDRESS TO BE PROGRAMMED WAIT FOR A TIME, tPROG COMPLETED PROGRAMMING THIS ROW? YES NO NOTES: The time between each FLASH address change (step 7 to step 7) or the time between the last FLASH address programmed to clearing PGM bit (step 7 to step10) must not exceed the maximum programming time, tPROG, maximum. This row program algorithm assumes the row/s to be programmed are initially erased. 10 CLEAR PGM BIT 11 WAIT FOR A TIME, tNVH 12 CLEAR HVEN BIT 13 WAIT FOR A TIME, tRCV END OF PROGRAMMING Figure 2-6. FLASH-1 Programming Algorithm Flowchart MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 49 Memory 2.7 FLASH-2 Memory (FLASH-2) This subsection describes the operation of the embedded FLASH-2 memory. This memory can be read, programmed, and erased from a single external supply. The program and erase operations are enabled through the use of an internal charge pump. 2.7.1 Functional Description The FLASH-2 memory is a non-continuous array consisting of a total of 29,822 bytes. An erased bit reads as a 1 and a programmed bit reads as a 0. Memory in the FLASH-2 array is organized into rows within pages. There are two rows of memory per page with 64 bytes per row. The minimum erase block size is a single page,128 bytes. Programming is performed on a per-row basis, 64 bytes at a time. Program and erase operations are facilitated through control bits in the FLASH-2 control register (FL2CR). Details for these operations appear later in this subsection. The FLASH-2 memory map consists of: * $0462-$04FF: user memory (158 bytes) * $0980-$1B7F: user memory (4608 bytes) * $1E20-$7FFF: user memory (25056 bytes) * $FF81: FLASH-2 block protect register (FL2BPR) NOTE FL2BPR physically resides within FLASH-1 memory addressing space * $FE08: FLASH-2 control register (FL2CR) Programming tools are available from Freescale Semiconductor. Contact your local representative for more information. NOTE A security feature prevents viewing of the FLASH contents.(1) 2.7.2 FLASH-2 Control and Block Protect Registers The FLASH-2 array has two registers that control its operation, the FLASH-2 control register (FL2CR) and the FLASH-2 block protect register (FL2BPR). 2.7.2.1 FLASH-2 Control Register The FLASH-2 control register (FL2CR) controls FLASH-2 program and erase operations. Address: Read: $FE08 Bit 7 6 5 4 0 0 0 0 0 0 0 0 Write: Reset: 3 2 1 Bit 0 HVEN MASS ERASE PGM 0 0 0 0 = Unimplemented Figure 2-7. FLASH-2 Control Register (FL2CR) 1. No security feature is absolutely secure. However, Freescale's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 50 Freescale Semiconductor FLASH-2 Memory (FLASH-2) HVEN -- High-Voltage Enable Bit This read/write bit enables the charge pump to drive high voltages for program and erase operations in the array. HVEN can only be set if either PGM = 1 or ERASE = 1 and the proper sequence for program or erase is followed. 1 = High voltage enabled to array and charge pump on 0 = High voltage disabled to array and charge pump off MASS -- Mass Erase Control Bit Setting this read/write bit configures the FLASH-2 array for mass or page erase operation. 1 = Mass erase operation selected 0 = Page erase operation selected ERASE -- Erase Control Bit This read/write bit configures the memory for erase operation. ERASE is interlocked with the PGM bit such that both bits cannot be set at the same time. 1 = Erase operation selected 0 = Erase operation unselected PGM -- Program Control Bit This read/write bit configures the memory for program operation. PGM is interlocked with the ERASE bit such that both bits cannot be equal to 1 or set to 1 at the same time. 1 = Program operation selected 0 = Program operation unselected 2.7.2.2 FLASH-2 Block Protect Register The FLASH-2 block protect register (FL2BPR) is implemented as a byte within the FLASH-1 memory; therefore, can only be written during a FLASH-1 programming sequence. The value in this register determines the starting location of the protected range within the FLASH-2 memory. Address: Read: Write: Reset: $FF81 Bit 7 6 5 4 3 2 1 Bit 0 BPR7 BPR6 BPR5 BPR4 BPR3 BPR2 BPR1 BPR0 Unaffected by reset Figure 2-8. FLASH-2 Block Protect Register (FL2BPR) NOTE The FLASH-2 block protect register (FL2BPR) controls the block protection for the FLASH-2 array. However, FL2BPR is implemented within the FLASH-1 memory array and therefore, the FLASH-1 control register (FL1CR) must be used to program/erase FL2BPR. FL2BPR[7:0] -- Block Protect Register Bits 7 to 0 These eight bits represent bits [14:7] of a 16-bit memory address. Bit 15 is a 0 and bits [6:0] are 0s. The resultant 16-bit address is used for specifying the start address of the FLASH-2 memory for block protection. FLASH-2 is protected from this start address to the end of FLASH-2 memory at $7FFF. With this mechanism, the protect start address can be $XX00 and $XX80 (128 byte page boundaries) within the FLASH-2 array. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 51 Memory 16-BIT MEMORY ADDRESS START ADDRESS OF FLASH BLOCK PROTECT 0 FLBPR VALUE 0 0 0 0 0 0 0 Figure 2-9. FLASH-2 Block Protect Start Address Table 2-3. FLASH-2 Protected Ranges FL2BPR[7:0] Protected Range $FF No Protection $FE $7F00-$7FFF $FD $0B $7E80-$7FFF $0580-$7FFF $0A $0500-$7FFF $09 $0480-$7FFF $08 $04 $0462-$7FFF $0462-$7FFF $03 $0462-$7FFF $02 $0462-$7FFF $01 $0462-$7FFF $00 $0462-$7FFF Decreasing the value in FL2BPR by one increases the protected range by one page (128 bytes). However, programming the block protect register with $FE protects a range twice that size, 256 bytes, in the corresponding array. $FE means that locations $7F00-$7FFF are protected in FLASH-2. The FLASH memory does not exist at some locations. The block protection range configuration is unaffected if FLASH memory does not exist in that range. Refer to Figure 2-1 and make sure that the desired locations are protected. 2.7.3 FLASH-2 Block Protection Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target application, provision is made for protecting blocks of memory from unintentional erase or program operations due to system malfunction. This protection is done by using the FLASH-2 block protection register (FL2BPR). FL2BPR determines the range of the FLASH-2 memory which is to be protected. The range of the protected area starts from a location defined by FL2BPR and ends at the bottom of the FLASH-2 memory ($7FFF). When the memory is protected, the HVEN bit can not be set in either ERASE or PROGRAM operations. NOTE In performing a program or erase operation, the FLASH-2 block protect register must be read after setting the PGM or ERASE bit and before asserting the HVEN bit. When the FLASH-2 block protect register is programmed with all 0's, the entire memory is protected from being programmed and erased. When all the bits are erased (all 1's), the entire memory is accessible for program and erase. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 52 Freescale Semiconductor FLASH-2 Memory (FLASH-2) When bits within FL2BPR are programmed (0), they lock a block of memory address ranges as shown in 2.7.2.2 FLASH-2 Block Protect Register. If FL2BPR is programmed with any value other than $FF, the protected block of FLASH memory can not be erased or programmed. NOTE The vector locations and the FLASH block protect registers are located in the same page. FL1BPR and FL2BPR are not protected with special hardware or software. Therefore, if this page is not protected by FL1BPR and the vector locations are erased by either a page or a mass erase operation, both FL1BPR and FL2BPR will also get erased. 2.7.4 FLASH-2 Mass Erase Operation Use this step-by-step procedure to erase the entire FLASH-2 memory: 1. Set both the ERASE bit and the MASS bit in the FLASH-2 control register (FL2CR). 2. Read the FLASH-2 block protect register (FL2BPR). NOTE Mass erase is disabled whenever any block is protected (FL2BPR does not equal $FF). 3. 4. 5. 6. 7. 8. 9. 10. Write to any FLASH-2 address within the FLASH-2 array with any data. Wait for a time, tNVS (minimum 10 s). Set the HVEN bit. Wait for a time, tMERASE (minimum 4 ms). Clear the ERASE and MASS bits. Wait for a time, tNVHL (minimum 100 s). Clear the HVEN bit. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 53 Memory 2.7.5 FLASH-2 Page Erase Operation Use this step-by-step procedure to erase a page (128 bytes) of FLASH-2 memory: 1. Set the ERASE bit and clear the MASS bit in the FLASH-2 control register (FL2CR). 2. Read the FLASH-2 block protect register (FL2BPR). 3. Write any data to any FLASH-2 address within the address range of the page (128 byte block) to be erased. 4. Wait for time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for time, tERASE (minimum 1 ms or 4 ms). 7. Clear the ERASE bit. 8. Wait for time, tNVH (minimum 5 s). 9. Clear the HVEN bit. 10. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. In applications that require more than 1000 program/erase cycles, use the 4 ms page erase specification to get improved long-term reliability. Any application can use this 4 ms page erase specification. However, in applications where a FLASH location will be erased and reprogrammed less than 1000 times, and speed is important, use the 1 ms page erase specification to get a shorter cycle time. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 54 Freescale Semiconductor FLASH-2 Memory (FLASH-2) 2.7.6 FLASH-2 Program Operation Programming of the FLASH memory is done on a row basis. A row consists of 64 consecutive bytes with address ranges as follows: * $XX00 to $XX3F * $XX40 to $XX7F * $XX80 to $XXBF * $XXC0 to $XXFF During the programming cycle, make sure that all addresses being written to fit within one of the ranges specified above. Attempts to program addresses in different row ranges in one programming cycle will fail. NOTE Only bytes which are currently $FF may be programmed. Use this step-by-step procedure to program a row of FLASH-2 memory: 1. Set the PGM bit in the FLASH-2 control register (FL2CR). This configures the memory for program operation and enables the latching of address and data programming. 2. Read the FLASH-2 block protect register (FL2BPR). 3. Write to any FLASH-2 address within the row address range desired with any data. 4. Wait for time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for time, tPGS (minimum 5 s). 7. Write data byte to the FLASH-2 address to be programmed. 8. Wait for time, t PROG (minimum 30 s). 9. Repeat step 7 and 8 until all the bytes within the row are programmed. 10. Clear the PGM bit. 11. Wait for time, tNVH (minimum 5 s). 12. Clear the HVEN bit. 13. Wait for a time, tRCV, (typically 1 s) after which the memory can be accessed in normal read mode. The FLASH programming algorithm flowchart is shown in Figure 2-10. NOTE A. Programming and erasing of FLASH locations can not be performed by code being executed from the same FLASH array. B. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. However, care must be taken to ensure that these operations do not access any address within the FLASH array memory space such as the COP control register (COPCTL) at $FFFF. C. It is highly recommended that interrupts be disabled during program/erase operations. D. Do not exceed t PROG maximum or tHV maximum. tHV is defined as the cumulative high voltage programming time to the same row before next erase. tHV must satisfy this condition: tNVS+ tNVH + tPGS + (tPROG X 64) tHV maximum MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 55 Memory E. The time between each FLASH address change (step 7 to step 7), or the time between the last FLASH address programmed to clearing the PGM bit (step 7 to step 10) must not exceed the maximum programming time, tPROG maximum. F. Be cautious when programming the FLASH-2 array to ensure that non-FLASH locations are not used as the address that is written to when selecting either the desired row address range in step 3 of the algorithm or the byte to be programmed in step 7 of the algorithm. 2.7.7 Low-Power Modes The WAIT and STOP instructions will place the MCU in low power-consumption standby modes. 2.7.7.1 Wait Mode Putting the MCU into wait mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly; however, no memory activity will take place since the CPU is inactive. The WAIT instruction should not be executed while performing a program or erase operation on the FLASH. Wait mode will suspend any FLASH program/erase operations and leave the memory in a standby mode. 2.7.7.2 Stop Mode Putting the MCU into stop mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly; however, no memory activity will take place since the CPU is inactive. The STOP instruction should not be executed while performing a program or erase operation on the FLASH. Stop mode will suspend any FLASH program/erase operations and leave the memory in a standby mode. NOTE Standby mode is the power saving mode of the FLASH module, in which all internal control signals to the FLASH are inactive and the current consumption of the FLASH is minimum. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 56 Freescale Semiconductor FLASH-2 Memory (FLASH-2) Algorithm for programming a row (64 bytes) of FLASH memory 1 SET PGM BIT 2 READ THE FLASH BLOCK PROTECT REGISTER 3 WRITE ANY DATA TO ANY FLASH ADDRESS WITHIN THE ROW ADDRESS RANGE DESIRED 4 WAIT FOR A TIME, tNVS 5 SET HVEN BIT 6 WAIT FOR A TIME, tPGS 7 8 WRITE DATA TO THE FLASH ADDRESS TO BE PROGRAMMED WAIT FOR A TIME, tPROG COMPLETED PROGRAMMING THIS ROW? YES NO NOTES: The time between each FLASH address change (step 7 to step 7) or the time between the last FLASH address programmed to clearing PGM bit (step 7 to step10) must not exceed the maximum programming time, tPROG, maximum. This row program algorithm assumes the row/s to be programmed are initially erased. 10 CLEAR PGM BIT 11 WAIT FOR A TIME, tNVH 12 CLEAR HVEN BIT 13 WAIT FOR A TIME, tRCV END OF PROGRAMMING Figure 2-10. FLASH-2 Programming Algorithm Flowchart MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 57 Memory MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 58 Freescale Semiconductor Chapter 3 Analog-to-Digital Converter (ADC) 3.1 Introduction This section describes the 10-bit analog-to-digital converter (ADC). 3.2 Features Features of the ADC module include: * 24 channels with multiplexed input * Linear successive approximation with monotonicity * 10-bit resolution * Single or continuous conversion * Conversion complete flag or conversion complete interrupt * Selectable ADC clock * Left or right justified result * Left justified sign data mode 3.3 Functional Description The ADC provides 24 pins for sampling external sources at pins PTG7/AD23-PTG0/AD16, PTA7/KBD7/AD15-PTA0/KBD0/AD8, and PTB7/AD7-PTB0/AD0. An analog multiplexer allows the single ADC converter to select one of 24 ADC channels as ADC voltage in (VADIN). VADIN is converted by the successive approximation register-based analog-to-digital converter. When the conversion is completed, ADC places the result in the ADC data register and sets a flag or generates an interrupt. See Figure 3-2. 3.3.1 ADC Port I/O Pins PTG7/AD23-PTG0/AD16, PTA7/KBD7/AD15-PTA0/KBD0/AD8, and PTB7/AD7-PTB0/AD0 are general-purpose I/O (input/output) pins that share with the ADC channels. The channel select bits define which ADC channel/port pin will be used as the input signal. The ADC overrides the port I/O logic by forcing that pin as input to the ADC. The remaining ADC channels/port pins are controlled by the port I/O logic and can be used as general-purpose I/O. Writes to the port register or data direction register (DDR) will not have any affect on the port pin that is selected by the ADC. A read of a port pin in use by the ADC will return a 0. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 59 Analog-to-Digital Converter (ADC) INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE VSSAD/VREFL SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH COMPUTER OPERATING PROPERLY MODULE PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG IRQ(1) PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE RST(1) 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 3-1. Block Diagram Highlighting ADC Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 60 Freescale Semiconductor Functional Description INTERNAL DATA BUS READ DDRx WRITE DDRx DISABLE DDRx RESET WRITE PTx PTx PTx ADC CHANNEL x READ PTx DISABLE ADC DATA REGISTER INTERRUPT LOGIC AIEN CONVERSION COMPLETE ADC ADC VOLTAGE IN (VADIN) CHANNEL SELECT ADCH4-ADCH0 ADC CLOCK COCO CGMXCLK BUS CLOCK CLOCK GENERATOR ADIV2-ADIV0 ADICLK Figure 3-2. ADC Block Diagram 3.3.2 Voltage Conversion When the input voltage to the ADC equals VREFH, the ADC converts the signal to $3FF (full scale). If the input voltage equals VREFL, the ADC converts it to $000. Input voltages between VREFH and VREFL are a straight-line linear conversion. NOTE The ADC input voltage must always be greater than VSSAD and less than VDDAD. Connect the VDDAD pin to the same voltage potential as the VDD pin, and connect the VSSAD pin to the same voltage potential as the VSS pin. The VDDAD pin should be routed carefully for maximum noise immunity. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 61 Analog-to-Digital Converter (ADC) 3.3.3 Conversion Time Conversion starts after a write to the ADC status and control register (ADSCR). One conversion will take between 16 and 17 ADC clock cycles. The ADIVx and ADICLK bits should be set to provide a 1-MHz ADC clock frequency. Conversion time = 16 to 17 ADC cycles ADC frequency Number of bus cycles = conversion time x bus frequency 3.3.4 Conversion In continuous conversion mode, the ADC data register will be filled with new data after each conversion. Data from the previous conversion will be overwritten whether that data has been read or not. Conversions will continue until the ADCO bit is cleared. The COCO bit is set after each conversion and will stay set until the next read of the ADC data register. In single conversion mode, conversion begins with a write to the ADSCR. Only one conversion occurs between writes to the ADSCR. When a conversion is in process and the ADSCR is written, the current conversion data should be discarded to prevent an incorrect reading. 3.3.5 Accuracy and Precision The conversion process is monotonic and has no missing codes. 3.3.6 Result Justification The conversion result may be formatted in four different ways: 1. Left justified 2. Right justified 3. Left Justified sign data mode 4. 8-bit truncation mode All four of these modes are controlled using MODE0 and MODE1 bits located in the ADC clock register (ADCLK). Left justification will place the eight most significant bits (MSB) in the corresponding ADC data register high, ADRH. This may be useful if the result is to be treated as an 8-bit result where the two least significant bits (LSB), located in the ADC data register low, ADRL, can be ignored. However, ADRL must be read after ADRH or else the interlocking will prevent all new conversions from being stored. Right justification will place only the two MSBs in the corresponding ADC data register high, ADRH, and the eight LSBs in ADC data register low, ADRL. This mode of operation typically is used when a 10-bit unsigned result is desired. Left justified sign data mode is similar to left justified mode with one exception. The MSB of the 10-bit result, AD9 located in ADRH, is complemented. This mode of operation is useful when a result, represented as a signed magnitude from mid-scale, is needed. Finally, 8-bit truncation mode will place the eight MSBs in the ADC data register low, ADRL. The two LSBs are dropped. This mode of operation is used when compatibility with 8-bit ADC designs are required. No interlocking between ADRH and ADRL is present. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 62 Freescale Semiconductor Monotonicity NOTE Quantization error is affected when only the most significant eight bits are used as a result. See Figure 3-3. 8-BIT 10-BIT RESULT RESULT IDEAL 8-BIT CHARACTERISTIC WITH QUANTIZATION = 1/2 10-BIT TRUNCATED TO 8-BIT RESULT 003 00B 00A 009 002 IDEAL 10-BIT CHARACTERISTIC WITH QUANTIZATION = 1/2 008 007 006 005 001 004 WHEN TRUNCATION IS USED, ERROR FROM IDEAL 8-BIT = 3/8 LSB DUE TO NON-IDEAL QUANTIZATION. 003 002 001 000 000 1/2 2 1/2 1 1/2 1/2 4 1/2 3 1/2 6 1/2 5 1/2 1 1/2 8 1/2 7 1/2 9 1/2 2 1/2 INPUT VOLTAGE REPRESENTED AS 10-BIT INPUT VOLTAGE REPRESENTED AS 8-BIT Figure 3-3. Bit Truncation Mode Error 3.4 Monotonicity The conversion process is monotonic and has no missing codes. 3.5 Interrupts When the AIEN bit is set, the ADC module is capable of generating CPU interrupts after each ADC conversion. A CPU interrupt is generated if the COCO bit is a 0. The COCO bit is not used as a conversion complete flag when interrupts are enabled. 3.6 Low-Power Modes The WAIT and STOP instruction can put the MCU in low power- consumption standby modes. 3.6.1 Wait Mode The ADC continues normal operation during wait mode. Any enabled CPU interrupt request from the ADC can bring the MCU out of wait mode. If the ADC is not required to bring the MCU out of wait mode, power MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 63 Analog-to-Digital Converter (ADC) down the ADC by setting ADCH4-ADCH0 bits in the ADC status and control register before executing the WAIT instruction. 3.6.2 Stop Mode The ADC module is inactive after the execution of a STOP instruction. Any pending conversion is aborted. ADC conversions resume when the MCU exits stop mode after an external interrupt. Allow one conversion cycle to stabilize the analog circuitry. 3.7 I/O Signals The ADC module has eight pins shared with port A and the KBI module: PTA7/KBD7/AD15-PTA0/KBD0/AD8 The ADC module has eight pins shared with port B: PTB7/AD7-PTB0/AD0 The ADC module has eight pins shared with port G: PTG7/AD23-PTG0/AD16 3.7.1 ADC Analog Power Pin (VDDAD) The ADC analog portion uses VDDAD as its power pin. Connect the VDDAD pin to the same voltage potential as VDD. External filtering may be necessary to ensure clean VDDAD for good results. NOTE For maximum noise immunity, route VDDAD carefully and place bypass capacitors as close as possible to the package. VDDAD and VREFH are bonded internally. 3.7.2 ADC Analog Ground Pin (VSSAD) The ADC analog portion uses VSSAD as its ground pin. Connect the VSSAD pin to the same voltage potential as VSS. NOTE Route VSSAD cleanly to avoid any offset errors. VSSAD and VREFL are bonded internally. 3.7.3 ADC Voltage Reference High Pin (VREFH) The ADC analog portion uses VREFH as its upper voltage reference pin. By default, connect the VREFH pin to the same voltage potential as VDD. External filtering is often necessary to ensure a clean VREFH for good results. Any noise present on this pin will be reflected and possibly magnified in A/D conversion values. NOTE For maximum noise immunity, route VREFH carefully and place bypass capacitors as close as possible to the package. Routing VREFH close and parallel to VREFL may improve common mode noise rejection. VDDAD and VREFH are bonded internally. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 64 Freescale Semiconductor I/O Registers 3.7.4 ADC Voltage Reference Low Pin (VREFL) The ADC analog portion uses VREFL as its lower voltage reference pin. By default, connect the VREFL pin to the same voltage potential as VSS. External filtering is often necessary to ensure a clean VREFL for good results. Any noise present on this pin will be reflected and possibly magnified in A/D conversion values. NOTE For maximum noise immunity, route VREFL carefully and, if not connected to VSS, place bypass capacitors as close as possible to the package. Routing VREFH close and parallel to VREFL may improve common mode noise rejection. VSSAD and VREFL are bonded internally. 3.7.5 ADC Voltage In (VADIN) VADIN is the input voltage signal from one of the 24 ADC channels to the ADC module. 3.8 I/O Registers These I/O registers control and monitor ADC operation: * ADC status and control register (ADSCR) * ADC data register (ADRH and ADRL) * ADC clock register (ADCLK) 3.8.1 ADC Status and Control Register Function of the ADC status and control register (ADSCR) is described here. Address: $003C Bit 7 6 5 4 3 2 1 Bit 0 AIEN ADCO ADCH4 ADCH3 ADCH2 ADCH1 ADCH0 0 0 0 1 1 1 1 1 R = Reserved Read: COCO Write: R Reset: Figure 3-4. ADC Status and Control Register (ADSCR) COCO -- Conversions Complete Bit In non-interrupt mode (AIEN = 0), COCO is a read-only bit that is set at the end of each conversion. COCO will stay set until cleared by a read of the ADC data register. Reset clears this bit. In interrupt mode (AIEN = 1), COCO is a read-only bit that is not set at the end of a conversion. It always reads as a 0. 1 = Conversion completed (AIEN = 0) 0 = Conversion not completed (AIEN = 0) or CPU interrupt enabled (AIEN = 1) NOTE The write function of the COCO bit is reserved. When writing to the ADSCR register, always have a 0 in the COCO bit position. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 65 Analog-to-Digital Converter (ADC) AIEN -- ADC Interrupt Enable Bit When this bit is set, an interrupt is generated at the end of an ADC conversion. The interrupt signal is cleared when the data register is read or the status/control register is written. Reset clears the AIEN bit. 1 = ADC interrupt enabled 0 = ADC interrupt disabled ADCO -- ADC Continuous Conversion Bit When set, the ADC will convert samples continuously and update the ADR register at the end of each conversion. Only one conversion is completed between writes to the ADSCR when this bit is cleared. Reset clears the ADCO bit. 1 = Continuous ADC conversion 0 = One ADC conversion ADCH4-ADCH0 -- ADC Channel Select Bits ADCH4-ADCH0 form a 5-bit field which is used to select one of 32 ADC channels. Only 24 channels, AD23-AD0, are available on this MCU. The channels are detailed in Table 3-1. Care should be taken when using a port pin as both an analog and digital input simultaneously to prevent switching noise from corrupting the analog signal. See Table 3-1. The ADC subsystem is turned off when the channel select bits are all set to 1. This feature allows for reduced power consumption for the MCU when the ADC is not being used. NOTE Recovery from the disabled state requires one conversion cycle to stabilize. The voltage levels supplied from internal reference nodes, as specified in Table 3-1, are used to verify the operation of the ADC converter both in production test and for user applications. Table 3-1. Mux Channel Select(1) ADCH4 ADCH3 ADCH2 ADCH1 ADCH0 Input Select 0 0 0 0 0 PTB0/AD0 0 0 0 0 1 PTB1/AD1 0 0 0 1 0 PTB2/AD2 0 0 0 1 1 PTB3/AD3 0 0 1 0 0 PTB4/AD4 0 0 1 0 1 PTB5/AD5 0 0 1 1 0 PTB6/AD6 0 0 1 1 1 PTB7/AD7 0 1 0 0 0 PTA0/KBD0/AD8 0 1 0 0 1 PTA1/KBD1/AD9 0 1 0 1 0 PTA2/KBD2/AD10 0 1 0 1 1 PTA3/KBD3/AD11 0 1 1 0 0 PTA4/KBD4/AD12 0 1 1 0 1 PTA5/KBD5/AD13 0 1 1 1 0 PTA6/KBD6/AD14 0 1 1 1 1 PTA7/KBD7/AD15 Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 66 Freescale Semiconductor I/O Registers Table 3-1. Mux Channel Select(1) (Continued) ADCH4 ADCH3 ADCH2 ADCH1 ADCH0 Input Select 1 0 0 0 0 PTG0/AD16 1 0 0 0 1 PTG1/AD17 1 0 0 1 0 PTG2/AD18 1 0 0 1 1 PTG3/AD19 1 0 1 0 0 PTG4/AD20 1 0 1 0 1 PTG5/AD21 1 0 1 1 0 PTG6/AD22 1 0 1 1 1 PTG7/AD23 1 1 1 1 0 1 0 0 0 0 Unused 1 1 1 0 1 VREFH 1 1 1 1 0 VREFL 1 1 1 1 1 ADC power off 1. If any unused channels are selected, the resulting ADC conversion will be unknown or reserved. 3.8.2 ADC Data Register High and Data Register Low 3.8.2.1 Left Justified Mode In left justified mode, the ADRH register holds the eight MSBs of the 10-bit result. The ADRL register holds the two LSBs of the 10-bit result. All other bits read as 0. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. All subsequent results will be lost until the ADRH and ADRL reads are completed. Address: Read: $003D ADRH Bit 7 6 5 4 3 2 1 Bit 0 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 Write: Reset: Address: Read: Unaffected by reset $003E AD1 ADRL AD0 0 0 0 0 0 0 Write: Reset: Unaffected by reset = Unimplemented Figure 3-5. ADC Data Register High (ADRH) and Low (ADRL) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 67 Analog-to-Digital Converter (ADC) 3.8.2.2 Right Justified Mode In right justified mode, the ADRH register holds the two MSBs of the 10-bit result. All other bits read as 0. The ADRL register holds the eight LSBs of the 10-bit result. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. All subsequent results will be lost until the ADRH and ADRL reads are completed. Address: Read: $003D ADRH Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 AD9 AD8 Write: Reset: Address: Read: Unaffected by reset $003E AD7 ADRL AD6 AD5 AD4 AD3 AD2 AD1 AD0 Write: Reset: Unaffected by reset = Unimplemented Figure 3-6. ADC Data Register High (ADRH) and Low (ADRL) 3.8.2.3 Left Justified Signed Data Mode In left justified signed data mode, the ADRH register holds the eight MSBs of the 10-bit result. The only difference from left justified mode is that the AD9 is complemented. The ADRL register holds the two LSBs of the 10-bit result. All other bits read as 0. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. All subsequent results will be lost until the ADRH and ADRL reads are completed. Address: Read: $003D Bit 7 6 5 4 3 2 1 Bit 0 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 0 0 0 Write: Reset: Address: Read: Unaffected by reset $003E AD1 AD0 0 0 0 Write: Reset: Unaffected by reset = Unimplemented Figure 3-7. ADC Data Register High (ADRH) and Low (ADRL) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 68 Freescale Semiconductor I/O Registers 3.8.2.4 Eight Bit Truncation Mode In 8-bit truncation mode, the ADRL register holds the eight MSBs of the 10-bit result. The ADRH register is unused and reads as 0. The ADRL register is updated each time an ADC single channel conversion completes. In 8-bit mode, the ADRL register contains no interlocking with ADRH. Address: Read: $003D ADRH Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Write: Reset: Address: Read: Unaffected by reset $003E ADRL AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 Write: Reset: Unaffected by reset = Unimplemented Figure 3-8. ADC Data Register High (ADRH) and Low (ADRL) 3.8.3 ADC Clock Register The ADC clock register (ADCLK) selects the clock frequency for the ADC. Address: Read: Write: Reset: $003F Bit 7 6 5 4 3 2 1 ADIV2 ADIV1 ADIV0 ADICLK MODE1 MODE0 R 0 0 0 0 0 1 0 R = Reserved = Unimplemented Bit 0 0 0 Figure 3-9. ADC Clock Register (ADCLK) ADIV2-ADIV0 -- ADC Clock Prescaler Bits ADIV2-ADIV0 form a 3-bit field which selects the divide ratio used by the ADC to generate the internal ADC clock. Table 3-2 shows the available clock configurations. The ADC clock should be set to approximately 1 MHz. Table 3-2. ADC Clock Divide Ratio ADIV2 ADIV1 ADIV0 ADC Clock Rate 0 0 0 ADC input clock / 1 0 0 1 ADC input clock / 2 0 1 0 ADC input clock / 4 0 1 1 ADC input clock / 8 1 X(1) X(1) ADC input clock / 16 1. X = Don't care MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 69 Analog-to-Digital Converter (ADC) ADICLK -- ADC Input Clock Select Bit ADICLK selects either the bus clock or the oscillator output clock (CGMXCLK) as the input clock source to generate the internal ADC clock. Reset selects CGMXCLK as the ADC clock source. 1 = Internal bus clock 0 = Oscillator output clock (CGMXCLK) The ADC requires a clock rate of approximately 1 MHz for correct operation. If the selected clock source is not fast enough, the ADC will generate incorrect conversions. See 20.10 5.0-Volt ADC Characteristics. fADIC = fCGMXCLK or bus frequency 1 MHz ADIV[2:0] MODE1 and MODE0 -- Modes of Result Justification Bits MODE1 and MODE0 select among four modes of operation. The manner in which the ADC conversion results will be placed in the ADC data registers is controlled by these modes of operation. Reset returns right-justified mode. 00 = 8-bit truncation mode 01 = Right justified mode 10 = Left justified mode 11 = Left justified signed data mode MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 70 Freescale Semiconductor Chapter 4 Clock Generator Module (CGM) 4.1 Introduction This section describes the clock generator module. The CGM generates the crystal clock signal, CGMXCLK, which operates at the frequency of the crystal. The CGM also generates the base clock signal, CGMOUT, which is based on either the crystal clock divided by two or the phase-locked loop (PLL) clock, CGMVCLK, divided by two. In user mode, CGMOUT is the clock from which the SIM derives the system clocks, including the bus clock, which is at a frequency of CGMOUT/2. The PLL is a fully functional frequency generator designed for use with crystals or ceramic resonators. The PLL can generate a maximum bus frequency of 8 MHz using a 1-8MHz crystal or external clock source. 4.2 Features Features of the CGM include: * Phase-locked loop with output frequency in integer multiples of an integer dividend of the crystal reference * High-frequency crystal operation with low-power operation and high-output frequency resolution * Programmable hardware voltage-controlled oscillator (VCO) for low-jitter operation * Automatic bandwidth control mode for low-jitter operation * Automatic frequency lock detector * CPU interrupt on entry or exit from locked condition * Configuration register bit to allow oscillator operation during stop mode 4.3 Functional Description The CGM consists of three major submodules: * Crystal oscillator circuit -- The crystal oscillator circuit generates the constant crystal frequency clock, CGMXCLK. * Phase-locked loop (PLL) -- The PLL generates the programmable VCO frequency clock, CGMVCLK. * Base clock selector circuit -- This software-controlled circuit selects either CGMXCLK divided by two or the VCO clock, CGMVCLK, divided by two as the base clock, CGMOUT. The SIM derives the system clocks from either CGMOUT or CGMXCLK. Figure 4-1 shows the structure of the CGM. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 71 Clock Generator Module (CGM) OSCILLATOR (OSC) OSC2 CGMXCLK (TO: SIM, TBM, ADC) OSC1 SIMOSCEN (FROM SIM) OSCENINSTOP (FROM CONFIG) PHASE-LOCKED LOOP (PLL) CGMRCLK CLOCK SELECT CIRCUIT BCS VDDA CGMXFC /2 A CGMOUT B S* (TO SIM) SIMDIV2 (FROM SIM) *WHEN S = 1, VSSA CGMOUT = B VPR1-VPR0 VRS7-VRS0 PHASE DETECTOR VOLTAGE CONTROLLED OSCILLATOR LOOP FILTER CGMVCLK PLL ANALOG LOCK DETECTOR LOCK AUTOMATIC MODE CONTROL AUTO ACQ CGMINT INTERRUPT CONTROL PLLIE (TO SIM) PLLF MUL11-MUL0 CGMVDV FREQUENCY DIVIDER Figure 4-1. CGM Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 72 Freescale Semiconductor Functional Description 4.3.1 Crystal Oscillator Circuit The crystal oscillator circuit consists of an inverting amplifier and an external crystal. The OSC1 pin is the input to the amplifier and the OSC2 pin is the output. The SIMOSCEN signal from the system integration module (SIM) or the OSCENINSTOP bit in the CONFIG register enable the crystal oscillator circuit. The CGMXCLK signal is the output of the crystal oscillator circuit and runs at a rate equal to the crystal frequency. CGMXCLK is then buffered to produce CGMRCLK, the PLL reference clock. CGMXCLK can be used by other modules which require precise timing for operation. The duty cycle of CGMXCLK is not guaranteed to be 50% and depends on external factors, including the crystal and related external components. An externally generated clock also can feed the OSC1 pin of the crystal oscillator circuit. Connect the external clock to the OSC1 pin and let the OSC2 pin float. 4.3.2 Phase-Locked Loop Circuit (PLL) The PLL is a frequency generator that can operate in either acquisition mode or tracking mode, depending on the accuracy of the output frequency. The PLL can change between acquisition and tracking modes either automatically or manually. 4.3.3 PLL Circuits The PLL consists of these circuits: * Voltage-controlled oscillator (VCO) * Modulo VCO frequency divider * Phase detector * Loop filter * Lock detector The operating range of the VCO is programmable for a wide range of frequencies and for maximum immunity to external noise, including supply and CGMXFC noise. The VCO frequency is bound to a range from roughly one-half to twice the center-of-range frequency, fVRS. Modulating the voltage on the CGMXFC pin changes the frequency within this range. By design, fVRS is equal to the nominal center-of-range frequency, fNOM, (71.4 kHz) times a linear factor, L, and a power-of-two factor, E, or (L x 2E)fNOM. CGMRCLK is the PLL reference clock, a buffered version of CGMXCLK. CGMRCLK runs at a frequency, fRCLK. The VCO's output clock, CGMVCLK, running at a frequency, fVCLK, is fed back through a programmable modulo divider. The modulo divider reduces the VCO clock by a factor, N. The dividers output is the VCO feedback clock, CGMVDV, running at a frequency, fVDV = fVCLK/(N). (For more information, see 4.3.6 Programming the PLL.) The phase detector then compares the VCO feedback clock, CGMVDV, with the final reference clock, CGMRDV. A correction pulse is generated based on the phase difference between the two signals. The loop filter then slightly alters the DC voltage on the external capacitor connected to CGMXFC based on the width and direction of the correction pulse. The filter can make fast or slow corrections depending on its mode, described in 4.3.4 Acquisition and Tracking Modes. The value of the external capacitor and the reference frequency determines the speed of the corrections and the stability of the PLL. The lock detector compares the frequencies of the VCO feedback clock, CGMVDV, and the reference clock, CGMRCLK. Therefore, the speed of the lock detector is directly proportional to the reference frequency, fRCLK. The circuit determines the mode of the PLL and the lock condition based on this comparison. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 73 Clock Generator Module (CGM) 4.3.4 Acquisition and Tracking Modes The PLL filter is manually or automatically configurable into one of two operating modes: * Acquisition mode -- In acquisition mode, the filter can make large frequency corrections to the VCO. This mode is used at PLL start up or when the PLL has suffered a severe noise hit and the VCO frequency is far off the desired frequency. When in acquisition mode, the ACQ bit is clear in the PLL bandwidth control register. (See 4.5.2 PLL Bandwidth Control Register.) * Tracking mode -- In tracking mode, the filter makes only small corrections to the frequency of the VCO. PLL jitter is much lower in tracking mode, but the response to noise is also slower. The PLL enters tracking mode when the VCO frequency is nearly correct, such as when the PLL is selected as the base clock source. (See 4.3.8 Base Clock Selector Circuit.) The PLL is automatically in tracking mode when not in acquisition mode or when the ACQ bit is set. 4.3.5 Manual and Automatic PLL Bandwidth Modes The PLL can change the bandwidth or operational mode of the loop filter manually or automatically. Automatic mode is recommended for most users. In automatic bandwidth control mode (AUTO = 1), the lock detector automatically switches between acquisition and tracking modes. Automatic bandwidth control mode also is used to determine when the VCO clock, CGMVCLK, is safe to use as the source for the base clock, CGMOUT. (See 4.5.2 PLL Bandwidth Control Register.) If PLL interrupts are enabled, the software can wait for a PLL interrupt request and then check the LOCK bit. If interrupts are disabled, software can poll the LOCK bit continuously (for example, during PLL start up) or at periodic intervals. In either case, when the LOCK bit is set, the VCO clock is safe to use as the source for the base clock. (See 4.3.8 Base Clock Selector Circuit.) If the VCO is selected as the source for the base clock and the LOCK bit is clear, the PLL has suffered a severe noise hit and the software must take appropriate action, depending on the application. (See 4.6 Interrupts for information and precautions on using interrupts.) The following conditions apply when the PLL is in automatic bandwidth control mode: * The ACQ bit (See 4.5.2 PLL Bandwidth Control Register.) is a read-only indicator of the mode of the filter. (See 4.3.4 Acquisition and Tracking Modes.) * The ACQ bit is set when the VCO frequency is within a certain tolerance and is cleared when the VCO frequency is out of a certain tolerance. (See 4.8 Acquisition/Lock Time Specifications for more information.) * The LOCK bit is a read-only indicator of the locked state of the PLL. * The LOCK bit is set when the VCO frequency is within a certain tolerance and is cleared when the VCO frequency is out of a certain tolerance. (See 4.8 Acquisition/Lock Time Specifications for more information.) * CPU interrupts can occur if enabled (PLLIE = 1) when the PLL's lock condition changes, toggling the LOCK bit. (See 4.5.1 PLL Control Register.) The PLL also may operate in manual mode (AUTO = 0). Manual mode is used by systems that do not require an indicator of the lock condition for proper operation. Such systems typically operate well below fBUSMAX. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 74 Freescale Semiconductor Functional Description The following conditions apply when in manual mode: * ACQ is a writable control bit that controls the mode of the filter. Before turning on the PLL in manual mode, the ACQ bit must be clear. * Before entering tracking mode (ACQ = 1), software must wait a given time, tACQ (See 4.8 Acquisition/Lock Time Specifications.), after turning on the PLL by setting PLLON in the PLL control register (PCTL). * Software must wait a given time, tAL, after entering tracking mode before selecting the PLL as the clock source to CGMOUT (BCS = 1). * The LOCK bit is disabled. * CPU interrupts from the CGM are disabled. 4.3.6 Programming the PLL Use the following procedure to program the PLL. For reference, the variables used and their meaning are shown in Table 4-1. Table 4-1. Variable Definitions Variable Definition fBUSDES Desired bus clock frequency fVCLKDES Desired VCO clock frequency fRCLK Chosen reference crystal frequency fVCLK Calculated VCO clock frequency fBUS Calculated bus clock frequency fNOM Nominal VCO center frequency fVRS Programmed VCO center frequency NOTE The round function in the following equations means that the real number should be rounded to the nearest integer number. 1. Choose the desired bus frequency, fBUSDES. 2. Calculate the desired VCO frequency (four times the desired bus frequency). fVCLKDES = 4 x fBUSDES 3. Choose a practical PLL (crystal) reference frequency, fRCLK. Typically, the reference crystal is 1-8 MHz. Frequency errors to the PLL are corrected at a rate of fRCLK. For stability and lock time reduction, this rate must be as fast as possible. The VCO frequency must be an integer multiple of this rate. The relationship between the VCO frequency, fVCLK, and the reference frequency, fRCLK, is: fVCLK = (N) (fRCLK) N, the range multiplier, must be an integer. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 75 Clock Generator Module (CGM) In cases where desired bus frequency has some tolerance, choose fRCLK to a value determined either by other module requirements (such as modules which are clocked by CGMXCLK), cost requirements, or ideally, as high as the specified range allows. See Chapter 20 Electrical Specifications. After choosing N, the actual bus frequency can be determined using equation in 2 above. 4. Select a VCO frequency multiplier, N. f VCLKDES N = round -------------------------- f RCLK 5. Calculate and verify the adequacy of the VCO and bus frequencies fVCLK and fBUS. f VCLK = ( N ) x f RCLK f BUS = ( f VCLK ) 4 6. Select the VCO's power-of-two range multiplier E, according to Table 4-2. Table 4-2. Power-of-Two Range Selectors Frequency Range E 0 < fVCLK 8 MHz 0 8 MHz< fVCLK 16 MHz 1 16 MHz< fVCLK 32 MHz 2(1) 1. Do not program E to a value of 3. 7. Select a VCO linear range multiplier, L, where fNOM = 71.4 kHz fVCLK L = Round 2E x fNOM 8. Calculate and verify the adequacy of the VCO programmed center-of-range frequency, fVRS. The center-of-range frequency is the midpoint between the minimum and maximum frequencies attainable by the PLL. fVRS = (L x 2E) fNOM 9. For proper operation, E f NOM x 2 f VRS - f VCLK --------------------------2 10. Verify the choice of N, E, and L by comparing fVCLK to fVRS and fVCLKDES. For proper operation, fVCLK must be within the application's tolerance of fVCLKDES, and fVRS must be as close as possible to fVCLK. NOTE Exceeding the recommended maximum bus frequency or VCO frequency can crash the MCU. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 76 Freescale Semiconductor Functional Description 11. Program the PLL registers accordingly: a. In the VPR bits of the PLL control register (PCTL), program the binary equivalent of E. b. In the PLL multiplier select register low (PMSL) and the PLL multiplier select register high (PMSH), program the binary equivalent of N. If using a 1-8 MHz reference, the PMSL register must be reprogrammed from the reset value before enabling the PLL. c. In the PLL VCO range select register (PMRS), program the binary coded equivalent of L. Table 4-3 provides numeric examples (register values are in hexadecimal notation): Table 4-3. Numeric Example fBUS fRCLK N E L 500 kHz 1 MHz 002 0 1B 1.25 MHz 1 MHz 005 0 45 2.0 MHz 1 MHz 008 0 70 2.5 MHz 1 MHz 00A 1 45 3.0 MHz 1 MHz 00C 1 53 4.0 MHz 1 MHz 010 1 70 5.0 MHz 1 MHz 014 2 46 7.0 MHz 1 MHz 01C 2 62 8.0 MHz 1 MHz 020 2 70 4.3.7 Special Programming Exceptions The programming method described in 4.3.6 Programming the PLL does not account for two possible exceptions. A value of 0 for N or L is meaningless when used in the equations given. To account for these exceptions: * A 0 value for N is interpreted exactly the same as a value of 1. * A 0 value for L disables the PLL and prevents its selection as the source for the base clock. See 4.3.8 Base Clock Selector Circuit. 4.3.8 Base Clock Selector Circuit This circuit is used to select either the crystal clock, CGMXCLK, or the VCO clock, CGMVCLK, as the source of the base clock, CGMOUT. The two input clocks go through a transition control circuit that waits up to three CGMXCLK cycles and three CGMVCLK cycles to change from one clock source to the other. During this time, CGMOUT is held in stasis. The output of the transition control circuit is then divided by two to correct the duty cycle. Therefore, the bus clock frequency, which is one-half of the base clock frequency, is one-fourth the frequency of the selected clock (CGMXCLK or CGMVCLK). The BCS bit in the PLL control register (PCTL) selects which clock drives CGMOUT. The VCO clock cannot be selected as the base clock source if the PLL is not turned on. The PLL cannot be turned off if the VCO clock is selected. The PLL cannot be turned on or off simultaneously with the selection or deselection of the VCO clock. The VCO clock also cannot be selected as the base clock source if the factor L is programmed to a 0. This value would set up a condition inconsistent with the operation of the PLL, so that the PLL would be disabled and the crystal clock would be forced as the source of the base clock. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 77 Clock Generator Module (CGM) 4.3.9 CGM External Connections In its typical configuration, the CGM requires external components. Five of these are for the crystal oscillator and two or four are for the PLL. The crystal oscillator is normally connected in a Pierce oscillator configuration, as shown in Figure 4-2. Figure 4-2 shows only the logical representation of the internal components and may not represent actual circuitry. The oscillator configuration uses five components: * Crystal, X1 * Fixed capacitor, C1 * Tuning capacitor, C2 (can also be a fixed capacitor) * Feedback resistor, RB * Series resistor, RS The series resistor (RS) is included in the diagram to follow strict Pierce oscillator guidelines. Refer to the crystal manufacturer's data for more information regarding values for C1 and C2. Figure 4-2 also shows the external components for the PLL: * Bypass capacitor, CBYP * Filter network Routing should be done with great care to minimize signal cross talk and noise. SIMOSCEN OSCENINSTOP (FROM CONFIG) CGMXCLK OSC1 CGMXFC OSC2 VSSA VDDA VDD RB RS RF1 CF2 CBYP CF1 X1 C1 C2 Note: Filter network in box can be replaced with a single capacitor, but will degrade stability. Figure 4-2. CGM External Connections 4.4 I/O Signals The following paragraphs describe the CGM I/O signals. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 78 Freescale Semiconductor I/O Signals 4.4.1 Crystal Amplifier Input Pin (OSC1) The OSC1 pin is an input to the crystal oscillator amplifier. 4.4.2 Crystal Amplifier Output Pin (OSC2) The OSC2 pin is the output of the crystal oscillator inverting amplifier. 4.4.3 External Filter Capacitor Pin (CGMXFC) The CGMXFC pin is required by the loop filter to filter out phase corrections. An external filter network is connected to this pin. (See Figure 4-2.) NOTE To prevent noise problems, the filter network should be placed as close to the CGMXFC pin as possible, with minimum routing distances and no routing of other signals across the network. 4.4.4 PLL Analog Power Pin (VDDA) VDDA is a power pin used by the analog portions of the PLL. Connect the VDDA pin to the same voltage potential as the VDD pin. NOTE Route VDDA carefully for maximum noise immunity and place bypass capacitors as close as possible to the package. 4.4.5 PLL Analog Ground Pin (VSSA) VSSA is a ground pin used by the analog portions of the PLL. Connect the VSSA pin to the same voltage potential as the VSS pin. NOTE Route VSSA carefully for maximum noise immunity and place bypass capacitors as close as possible to the package. 4.4.6 Oscillator Enable Signal (SIMOSCEN) The SIMOSCEN signal comes from the system integration module (SIM) and enables the oscillator and PLL. 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP) OSCENINSTOP is a bit in the CONFIG2 register that enables the oscillator to continue operating during stop mode. If this bit is set, the oscillator continues running during stop mode. If this bit is not set (default), the oscillator is controlled by the SIMOSCEN signal which will disable the oscillator during stop mode. 4.4.8 Crystal Output Frequency Signal (CGMXCLK) CGMXCLK is the crystal oscillator output signal. It runs at the full speed of the crystal (fXCLK) and comes directly from the crystal oscillator circuit. Figure 4-2 shows only the logical relation of CGMXCLK to OSC1 and OSC2 and may not represent the actual circuitry. The duty cycle of CGMXCLK is unknown and may depend on the crystal and other external factors. Also, the frequency and amplitude of CGMXCLK can be unstable at start up. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 79 Clock Generator Module (CGM) 4.4.9 CGM Base Clock Output (CGMOUT) CGMOUT is the clock output of the CGM. This signal goes to the SIM, which generates the MCU clocks. CGMOUT is a 50 percent duty cycle clock running at twice the bus frequency. CGMOUT is software programmable to be either the oscillator output, CGMXCLK, divided by two or the VCO clock, CGMVCLK, divided by two. 4.4.10 CGM CPU Interrupt (CGMINT) CGMINT is the interrupt signal generated by the PLL lock detector. 4.5 CGM Registers These registers control and monitor operation of the CGM: * PLL control register (PCTL) -- see 4.5.1 PLL Control Register * PLL bandwidth control register (PBWC) -- see 4.5.2 PLL Bandwidth Control Register * PLL multiplier select register high (PMSH) -- see 4.5.3 PLL Multiplier Select Register High * PLL multiplier select register low (PMSL) -- see 4.5.4 PLL Multiplier Select Register Low * PLL VCO range select register (PMRS) -- see 4.5.5 PLL VCO Range Select Register Figure 4-3 is a summary of the CGM registers. Addr. $0036 $0037 $0038 $0039 $003A $003B Register Name Bit 7 PLL Control Register Read: (PCTL) Write: See page 81. Reset: PLL Bandwidth Control Read: Register (PBWC) Write: See page 82. Reset: PLL Multiplier Select High Read: Register (PMSH) Write: See page 83. Reset: PLL Multiplier Select Low Read: Register (PMSL) Write: See page 84. Reset: PLL VCO Select Range Read: Register (PMRS) Write: See page 84. Reset: Read: Reserved Register Write: Reset: PLLIE 0 AUTO 6 PLLF 0 LOCK 5 4 3 2 1 Bit 0 PLLON BCS R R VPR1 VPR0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 MUL11 MUL10 MUL9 MUL8 ACQ R 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MUL7 MUL6 MUL5 MUL4 MUL3 MUL2 MUL1 MUL0 0 1 0 0 0 0 0 0 VRS7 VRS6 VRS5 VRS4 VRS3 VRS2 VRS1 VRS0 0 0 1 0 0 0 0 0 0 0 0 0 R R R R 0 0 = Unimplemented 0 R 0 = Reserved 0 0 1 0 NOTES: 1. When AUTO = 0, PLLIE is forced clear and is read-only. 2. When AUTO = 0, PLLF and LOCK read as clear. 3. When AUTO = 1, ACQ is read-only. 4. When PLLON = 0 or VRS7:VRS0 = $0, BCS is forced clear and is read-only. 5. When PLLON = 1, the PLL programming register is read-only. 6. When BCS = 1, PLLON is forced set and is read-only. Figure 4-3. CGM I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 80 Freescale Semiconductor CGM Registers 4.5.1 PLL Control Register The PLL control register (PCTL) contains the interrupt enable and flag bits, the on/off switch, the base clock selector bit, and the VCO power-of-two range selector bits. Address: $0036 Bit 7 Read: Write: Reset: PLLIE 0 6 PLLF 5 4 3 2 1 Bit 0 PLLON BCS R R VPR1 VPR0 1 0 0 0 0 0 R = Reserved 0 = Unimplemented Figure 4-4. PLL Control Register (PCTL) PLLIE -- PLL Interrupt Enable Bit This read/write bit enables the PLL to generate an interrupt request when the LOCK bit toggles, setting the PLL flag, PLLF. When the AUTO bit in the PLL bandwidth control register (PBWC) is clear, PLLIE cannot be written and reads as 0. Reset clears the PLLIE bit. 1 = PLL interrupts enabled 0 = PLL interrupts disabled PLLF -- PLL Interrupt Flag Bit This read-only bit is set whenever the LOCK bit toggles. PLLF generates an interrupt request if the PLLIE bit also is set. PLLF always reads as 0 when the AUTO bit in the PLL bandwidth control register (PBWC) is clear. Clear the PLLF bit by reading the PLL control register. Reset clears the PLLF bit. 1 = Change in lock condition 0 = No change in lock condition NOTE Do not inadvertently clear the PLLF bit. Any read or read-modify-write operation on the PLL control register clears the PLLF bit. PLLON -- PLL On Bit This read/write bit activates the PLL and enables the VCO clock, CGMVCLK. PLLON cannot be cleared if the VCO clock is driving the base clock, CGMOUT (BCS = 1). (See 4.3.8 Base Clock Selector Circuit.) Reset sets this bit so that the loop can stabilize as the MCU is powering up. 1 = PLL on 0 = PLL off BCS -- Base Clock Select Bit This read/write bit selects either the crystal oscillator output, CGMXCLK, or the VCO clock, CGMVCLK, as the source of the CGM output, CGMOUT. CGMOUT frequency is one-half the frequency of the selected clock. BCS cannot be set while the PLLON bit is clear. After toggling BCS, it may take up to three CGMXCLK and three CGMVCLK cycles to complete the transition from one source clock to the other. During the transition, CGMOUT is held in stasis. (See 4.3.8 Base Clock Selector Circuit.) Reset clears the BCS bit. 1 = CGMVCLK divided by two drives CGMOUT 0 = CGMXCLK divided by two drives CGMOUT NOTE PLLON and BCS have built-in protection that prevents the base clock selector circuit from selecting the VCO clock as the source of the base clock MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 81 Clock Generator Module (CGM) if the PLL is off. Therefore, PLLON cannot be cleared when BCS is set, and BCS cannot be set when PLLON is clear. If the PLL is off (PLLON = 0), selecting CGMVCLK requires two writes to the PLL control register. (See 4.3.8 Base Clock Selector Circuit.). VPR1 and VPR0 -- VCO Power-of-Two Range Select Bits These read/write bits control the VCO's hardware power-of-two range multiplier E that, in conjunction with L controls the hardware center-of-range frequency, fVRS. VPR1:VPR0 cannot be written when the PLLON bit is set. Reset clears these bits. (See 4.3.3 PLL Circuits, 4.3.6 Programming the PLL, and 4.5.5 PLL VCO Range Select Register.) Table 4-4. VPR1 and VPR0 Programming VPR1 and VPR0 E VCO Power-of-Two Range Multiplier 00 0 1 01 1 2 10 2(1) 4 1. Do not program E to a value of 3. NOTE Verify that the value of the VPR1 and VPR0 bits in the PCTL register are appropriate for the given reference and VCO clock frequencies before enabling the PLL. See 4.3.6 Programming the PLL for detailed instructions on selecting the proper value for these control bits. 4.5.2 PLL Bandwidth Control Register The PLL bandwidth control register (PBWC): * Selects automatic or manual (software-controlled) bandwidth control mode * Indicates when the PLL is locked * In automatic bandwidth control mode, indicates when the PLL is in acquisition or tracking mode * In manual operation, forces the PLL into acquisition or tracking mode Address: $0037 Bit 7 Read: Write: Reset: AUTO 0 6 LOCK 5 ACQ 0 = Unimplemented 0 4 3 2 1 0 0 0 0 0 0 0 0 R = Reserved Bit 0 R 0 Figure 4-5. PLL Bandwidth Control Register (PBWC) AUTO -- Automatic Bandwidth Control Bit This read/write bit selects automatic or manual bandwidth control. When initializing the PLL for manual operation (AUTO = 0), clear the ACQ bit before turning on the PLL. Reset clears the AUTO bit. 1 = Automatic bandwidth control 0 = Manual bandwidth control MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 82 Freescale Semiconductor CGM Registers LOCK -- Lock Indicator Bit When the AUTO bit is set, LOCK is a read-only bit that becomes set when the VCO clock, CGMVCLK, is locked (running at the programmed frequency). When the AUTO bit is clear, LOCK reads as 0 and has no meaning. The write one function of this bit is reserved for test, so this bit must always be written as a 0. Reset clears the LOCK bit. 1 = VCO frequency correct or locked 0 = VCO frequency incorrect or unlocked ACQ -- Acquisition Mode Bit When the AUTO bit is set, ACQ is a read-only bit that indicates whether the PLL is in acquisition mode or tracking mode. When the AUTO bit is clear, ACQ is a read/write bit that controls whether the PLL is in acquisition or tracking mode. In automatic bandwidth control mode (AUTO = 1), the last-written value from manual operation is stored in a temporary location and is recovered when manual operation resumes. Reset clears this bit, enabling acquisition mode. 1 = Tracking mode 0 = Acquisition mode 4.5.3 PLL Multiplier Select Register High The PLL multiplier select register high (PMSH) contains the programming information for the high byte of the modulo feedback divider. Address: Read: $0038 Bit 7 6 5 4 0 0 0 0 0 0 0 0 Write: Reset: 3 2 1 Bit 0 MUL11 MUL10 MUL9 MUL8 0 0 0 0 = Unimplemented Figure 4-6. PLL Multiplier Select Register High (PMSH) MUL11-MUL8 -- Multiplier Select Bits These read/write bits control the high byte of the modulo feedback divider that selects the VCO frequency multiplier N. (See 4.3.3 PLL Circuits and 4.3.6 Programming the PLL.) A value of $0000 in the multiplier select registers configures the modulo feedback divider the same as a value of $0001. Reset initializes the registers to $0040 for a default multiply value of 64. NOTE The multiplier select bits have built-in protection such that they cannot be written when the PLL is on (PLLON = 1). PMSH[7:4] -- Unimplemented Bits These bits have no function and always read as 0s. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 83 Clock Generator Module (CGM) 4.5.4 PLL Multiplier Select Register Low The PLL multiplier select register low (PMSL) contains the programming information for the low byte of the modulo feedback divider. Address: Read: Write: Reset: $0038 Bit 7 6 5 4 3 2 1 Bit 0 MUL7 MUL6 MUL5 MUL4 MUL3 MUL2 MUL1 MUL0 0 1 0 0 0 0 0 0 Figure 4-7. PLL Multiplier Select Register Low (PMSL) NOTE For applications using 1-8 MHz reference frequencies this register must be reprogrammed before enabling the PLL. The reset value of this register will cause applications using 1-8 MHz reference frequencies to become unstable if the PLL is enabled without programming an appropriate value. The programmed value must not allow the VCO clock to exceed 32 MHz. See 4.3.6 Programming the PLL for detailed instructions on choosing the proper value for PMSL. MUL7-MUL0 -- Multiplier Select Bits These read/write bits control the low byte of the modulo feedback divider that selects the VCO frequency multiplier, N. (See 4.3.3 PLL Circuits and 4.3.6 Programming the PLL.) MUL7-MUL0 cannot be written when the PLLON bit in the PCTL is set. A value of $0000 in the multiplier select registers configures the modulo feedback divider the same as a value of $0001. Reset initializes the register to $40 for a default multiply value of 64. NOTE The multiplier select bits have built-in protection such that they cannot be written when the PLL is on (PLLON = 1). 4.5.5 PLL VCO Range Select Register The PLL VCO range select register (PMRS) contains the programming information required for the hardware configuration of the VCO. Address: Read: Write: Reset: $003A Bit 7 6 5 4 3 2 1 Bit 0 VRS7 VRS6 VRS5 VRS4 VRS3 VRS2 VRS1 VRS0 0 1 0 0 0 0 0 0 Figure 4-8. PLL VCO Range Select Register (PMRS) NOTE Verify that the value of the PMRS register is appropriate for the given reference and VCO clock frequencies before enabling the PLL. See 4.3.6 Programming the PLL for detailed instructions on selecting the proper value for these control bits. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 84 Freescale Semiconductor Interrupts VRS7-VRS0 -- VCO Range Select Bits These read/write bits control the hardware center-of-range linear multiplier L which, in conjunction with E (See 4.3.3 PLL Circuits, 4.3.6 Programming the PLL, and 4.5.1 PLL Control Register.), controls the hardware center-of-range frequency, fVRS. VRS7-VRS0 cannot be written when the PLLON bit in the PCTL is set. (See 4.3.7 Special Programming Exceptions.) A value of $00 in the VCO range select register disables the PLL and clears the BCS bit in the PLL control register (PCTL). (See 4.3.8 Base Clock Selector Circuit and 4.3.7 Special Programming Exceptions.). Reset initializes the register to $40 for a default range multiply value of 64. NOTE The VCO range select bits have built-in protection such that they cannot be written when the PLL is on (PLLON = 1) and such that the VCO clock cannot be selected as the source of the base clock (BCS = 1) if the VCO range select bits are all clear. The PLL VCO range select register must be programmed correctly. Incorrect programming can result in failure of the PLL to achieve lock. 4.6 Interrupts When the AUTO bit is set in the PLL bandwidth control register (PBWC), the PLL can generate a CPU interrupt request every time the LOCK bit changes state. The PLLIE bit in the PLL control register (PCTL) enables CPU interrupts from the PLL. PLLF, the interrupt flag in the PCTL, becomes set whether interrupts are enabled or not. When the AUTO bit is clear, CPU interrupts from the PLL are disabled and PLLF reads as 0. Software should read the LOCK bit after a PLL interrupt request to see if the request was due to an entry into lock or an exit from lock. When the PLL enters lock, the VCO clock, CGMVCLK, divided by two can be selected as the CGMOUT source by setting BCS in the PCTL. When the PLL exits lock, the VCO clock frequency is corrupt, and appropriate precautions should be taken. If the application is not frequency sensitive, interrupts should be disabled to prevent PLL interrupt service routines from impeding software performance or from exceeding stack limitations. NOTE Software can select the CGMVCLK divided by two as the CGMOUT source even if the PLL is not locked (LOCK = 0). Therefore, software should make sure the PLL is locked before setting the BCS bit. 4.7 Special Modes The WAIT instruction puts the MCU in low power-consumption standby modes. 4.7.1 Wait Mode The WAIT instruction does not affect the CGM. Before entering wait mode, software can disengage and turn off the PLL by clearing the BCS and PLLON bits in the PLL control register (PCTL) to save power. Less power-sensitive applications can disengage the PLL without turning it off, so that the PLL clock is immediately available at WAIT exit. This would be the case also when the PLL is to wake the MCU from wait mode, such as when the PLL is first enabled and waiting for LOCK or LOCK is lost. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 85 Clock Generator Module (CGM) 4.7.2 Stop Mode If the OSCENINSTOP bit in the CONFIG2 register is cleared (default), then the STOP instruction disables the CGM (oscillator and phase locked loop) and holds low all CGM outputs (CGMXCLK, CGMOUT, and CGMINT). If the OSCENINSTOP bit in the CONFIG2 register is set, then the phase locked loop is shut off but the oscillator will continue to operate in stop mode. 4.7.3 CGM During Break Interrupts The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear status bits during the break state. (See 14.7.3 Break Flag Control Register.) To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect the PLLF bit during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write the PLL control register during the break state without affecting the PLLF bit. 4.8 Acquisition/Lock Time Specifications The acquisition and lock times of the PLL are, in many applications, the most critical PLL design parameters. Proper design and use of the PLL ensures the highest stability and lowest acquisition/lock times. 4.8.1 Acquisition/Lock Time Definitions Typical control systems refer to the acquisition time or lock time as the reaction time, within specified tolerances, of the system to a step input. In a PLL, the step input occurs when the PLL is turned on or when it suffers a noise hit. The tolerance is usually specified as a percent of the step input or when the output settles to the desired value plus or minus a percent of the frequency change. Therefore, the reaction time is constant in this definition, regardless of the size of the step input. For example, consider a system with a 5 percent acquisition time tolerance. If a command instructs the system to change from 0 Hz to 1 MHz, the acquisition time is the time taken for the frequency to reach 1 MHz 50 kHz. Fifty kHz = 5% of the 1-MHz step input. If the system is operating at 1 MHz and suffers a -100-kHz noise hit, the acquisition time is the time taken to return from 900 kHz to 1 MHz 5 kHz. Five kHz = 5% of the 100-kHz step input. Other systems refer to acquisition and lock times as the time the system takes to reduce the error between the actual output and the desired output to within specified tolerances. Therefore, the acquisition or lock time varies according to the original error in the output. Minor errors may not even be registered. Typical PLL applications prefer to use this definition because the system requires the output frequency to be within a certain tolerance of the desired frequency regardless of the size of the initial error. 4.8.2 Parametric Influences on Reaction Time Acquisition and lock times are designed to be as short as possible while still providing the highest possible stability. These reaction times are not constant, however. Many factors directly and indirectly affect the acquisition time. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 86 Freescale Semiconductor Acquisition/Lock Time Specifications The most critical parameter which affects the reaction times of the PLL is the reference frequency, fRCLK. This frequency is the input to the phase detector and controls how often the PLL makes corrections. For stability, the corrections must be small compared to the desired frequency, so several corrections are required to reduce the frequency error. Therefore, the slower the reference the longer it takes to make these corrections. This parameter is under user control via the choice of crystal frequency fXCLK. (See 4.3.3 PLL Circuits and 4.3.6 Programming the PLL.) Another critical parameter is the external filter network. The PLL modifies the voltage on the VCO by adding or subtracting charge from capacitors in this network. Therefore, the rate at which the voltage changes for a given frequency error (thus change in charge) is proportional to the capacitance. The size of the capacitor also is related to the stability of the PLL. If the capacitor is too small, the PLL cannot make small enough adjustments to the voltage and the system cannot lock. If the capacitor is too large, the PLL may not be able to adjust the voltage in a reasonable time. (See 4.8.3 Choosing a Filter.) Also important is the operating voltage potential applied to VDDA. The power supply potential alters the characteristics of the PLL. A fixed value is best. Variable supplies, such as batteries, are acceptable if they vary within a known range at very slow speeds. Noise on the power supply is not acceptable, because it causes small frequency errors which continually change the acquisition time of the PLL. Temperature and processing also can affect acquisition time because the electrical characteristics of the PLL change. The part operates as specified as long as these influences stay within the specified limits. External factors, however, can cause drastic changes in the operation of the PLL. These factors include noise injected into the PLL through the filter capacitor, filter capacitor leakage, stray impedances on the circuit board, and even humidity or circuit board contamination. 4.8.3 Choosing a Filter As described in 4.8.2 Parametric Influences on Reaction Time, the external filter network is critical to the stability and reaction time of the PLL. The PLL is also dependent on reference frequency and supply voltage. Figure 4-9 shows two types of filter circuits. In low-cost applications, where stability and reaction time of the PLL are not critical, the three component filter network shown in Figure 4-9 (B) can be replaced by a single capacitor, CF, as shown in shown in Figure 4-9 (A). Refer to Table 4-5 for recommended filter components at various reference frequencies. For reference frequencies between the values listed in the table, extrapolate to the nearest common capacitor value. In general, a slightly larger capacitor provides more stability at the expense of increased lock time. CGMXFC CGMXFC RF1 CF2 CF CF1 VSSA VSSA (A) (B) Figure 4-9. PLL Filter MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 87 Clock Generator Module (CGM) Table 4-5. Example Filter Component Values fRCLK CF1 CF2 RF1 CF 1 MHz 8.2 nF 820 pF 2k 18 nF 2 MHz 4.7 nF 470 pF 2k 6.8 nF 3 MHz 3.3 nF 330 pF 2k 5.6 nF 4 MHz 2.2 nF 220 pF 2k 4.7 nF 5 MHz 1.8 nF 180 pF 2k 3.9 nF 6 MHz 1.5 nF 150 pF 2k 3.3 nF 7 MHz 1.2 nF 120 pF 2k 2.7 nF 8 MHz 1 nF 100 pF 2k 2.2 nF MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 88 Freescale Semiconductor Chapter 5 Configuration Register (CONFIG) 5.1 Introduction This section describes the configuration registers, CONFIG1 and CONFIG2. The configuration registers enable or disable these options: * Stop mode recovery time (32 CGMXCLK cycles or 4096 CGMXCLK cycles) * COP timeout period (262,128 or 8176 CGMXCLK cycles) * STOP instruction * Computer operating properly module (COP) * Low-voltage inhibit (LVI) module control and voltage trip point selection * Enable/disable the oscillator (OSC) during stop mode * Enable/disable an extra divide by 128 prescaler in timebase module * Selectable clockout (MCLK) feature with divide by 1, 2, and 4 of the bus or crystal frequency * Timebase clock select 5.2 Functional Description The configuration registers are used in the initialization of various options. The configuration registers can be written once after each reset. All of the configuration register bits are cleared during reset. Since the various options affect the operation of the microcontroller unit (MCU), it is recommended that these registers be written immediately after reset. The configuration registers are located at $001E and $001F and may be read at anytime. NOTE On a FLASH device, the options except LVI5OR3 are one-time writable by the user after each reset. This bit is one-time writable by the user only after each POR (power-on reset). The CONFIG registers are not in the FLASH memory but are special registers containing one-time writable latches after each reset. Upon a reset, the CONFIG registers default to predetermined settings as shown in Figure 5-1 and Figure 5-2. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 89 Configuration Register (CONFIG) Address: $001E Bit 7 Read: 0 Write: Reset: 6 5 4 3 MCLKSEL MCLK1 MCLK0 R 0 0 0 0 R = Reserved 0 = Unimplemented 2 1 Bit 0 TMBCLKSEL OSCENINSTOP SCIBDSRC 0 0 1 Figure 5-1. Configuration Register 2 (CONFIG2) MCLKSEL -- MCLK Source Select Bit 1 = Crystal frequency 0 = Bus frequency MCLK1 and MCLK0 -- MCLK Output Select Bits Setting the MCLK1 and MCLK0 bits enables the PTD0/SS pin to be used as a MCLK output clock. Once configured for MCLK, the PTD data direction register for PTD0 is used to enable and disable the MCLK output. See Table 5-1 for MCLK options. Table 5-1. MCLK Output Select MCLK1 MCLK0 MCLK Frequency 0 0 MCLK not enabled 0 1 Clock 1 0 Clock divided by 2 1 1 Clock divided by 4 TMBCLKSEL-- Timebase Clock Select Bit TMBCLKSEL enables an extra divide-by-128 prescaler in the timebase module. Setting this bit enables the extra prescaler and clearing this bit disables it. See Chapter 16 Timebase Module (TBM) for a more detailed description of the external clock operation. 1 = Enables extra divide-by-128 prescaler in timebase module 0 = Disables extra divide-by-128 prescaler in timebase module OSCENINSTOP -- Oscillator Enable In Stop Mode Bit OSCENINSTOP, when set, will enable the oscillator to continue to generate clocks in stop mode. See Chapter 4 Clock Generator Module (CGM). This function is used to keep the timebase running while the rest of the MCU stops. See Chapter 16 Timebase Module (TBM). When clear, the oscillator will cease to generate clocks while in stop mode. The default state for this option is clear, disabling the oscillator in stop mode. 1 = Oscillator enabled during stop mode 0 = Oscillator disabled during stop mode (default) SCIBDSRC -- SCI Baud Rate Clock Source Bit SCIBDSRC controls the clock source used for the serial communications interface (SCI). The setting of this bit affects the frequency at which the SCI operates.See Chapter 13 Enhanced Serial Communications Interface (ESCI) Module. 1 = Internal data bus clock used as clock source for SCI (default) 0 = External oscillator used as clock source for SCI MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 90 Freescale Semiconductor Functional Description Address: Read: Write: Reset: $001F Bit 7 6 5 4 3 2 1 Bit 0 COPRS LVISTOP LVIRSTD LVIPWRD LVI5OR3 SSREC STOP COPD 0 0 0 0 See note 0 0 0 Note: LVI5OR3 is only reset via POR (power-on reset). Figure 5-2. Configuration Register 1 (CONFIG1) COPRS -- COP Rate Select Bit COPRS selects the COP timeout period. Reset clears COPRS. See Chapter 6 Computer Operating Properly (COP) Module 1 = COP timeout period = 8176 CGMXCLK cycles 0 = COP timeout period = 262,128 CGMXCLK cycles LVISTOP -- LVI Enable in Stop Mode Bit When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to operate during stop mode. Reset clears LVISTOP. 1 = LVI enabled during stop mode 0 = LVI disabled during stop mode LVIRSTD -- LVI Reset Disable Bit LVIRSTD disables the reset signal from the LVI module. See Chapter 11 Low-Voltage Inhibit (LVI). 1 = LVI module resets disabled 0 = LVI module resets enabled LVIPWRD -- LVI Power Disable Bit LVIPWRD disables the LVI module. See Chapter 11 Low-Voltage Inhibit (LVI). 1 = LVI module power disabled 0 = LVI module power enabled LVI5OR3 -- LVI 5-V or 3-V Operating Mode Bit LVI5OR3 selects the voltage operating mode of the LVI module (see Chapter 11 Low-Voltage Inhibit (LVI)). The voltage mode selected for the LVI should match the operating VDD (see Chapter 20 Electrical Specifications) for the LVI's voltage trip points for each of the modes. 1 = LVI operates in 5-V mode 0 = LVI operates in 3-V mode NOTE The LVI5OR3 bit is cleared by a power-on reset (POR) only. Other resets will leave this bit unaffected. SSREC -- Short Stop Recovery Bit SSREC enables the CPU to exit stop mode with a delay of 32 CGMXCLK cycles instead of a 4096-CGMXCLK cycle delay. 1 = Stop mode recovery after 32 CGMXCLK cycles 0 = Stop mode recovery after 4096 CGMXCLK cycles NOTE Exiting stop mode by any reset will result in the long stop recovery. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 91 Configuration Register (CONFIG) The short stop recovery delay can be enabled when using a crystal or resonator and the OSCENINSTOP bit is set. The short stop recovery delay can be enabled when an external oscillator is used, regardless of the OSCENINSTOP setting. The short stop recovery delay must be disabled when the OSCENINSTOP bit is clear and a crystal or resonator is used. STOP -- STOP Instruction Enable Bit STOP enables the STOP instruction. 1 = STOP instruction enabled 0 = STOP instruction treated as illegal opcode COPD -- COP Disable Bit COPD disables the COP module. See Chapter 6 Computer Operating Properly (COP) Module. 1 = COP module disabled 0 = COP module enabled MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 92 Freescale Semiconductor Chapter 6 Computer Operating Properly (COP) Module 6.1 Introduction The computer operating properly (COP) module contains a free-running counter that generates a reset if allowed to overflow. The COP module helps software recover from runaway code. Prevent a COP reset by clearing the COP counter periodically. The COP module can be disabled through the COPD bit in the CONFIG register. 6.2 Functional Description Figure 6-1 shows the structure of the COP module. INTERNAL RESET SOURCES RESET STATUS REGISTER COP TIMEOUT CLEAR STAGES 5-12 STOP INSTRUCTION RESET CIRCUIT 12-BIT SIM COUNTER CLEAR ALL STAGES CGMXCLK COPCTL WRITE COP CLOCK COP MODULE COPEN (FROM SIM) COP DISABLE (FROM CONFIG) RESET COPCTL WRITE 6-BIT COP COUNTER CLEAR COP COUNTER COP RATE SEL (FROM CONFIG) Figure 6-1. COP Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 93 Computer Operating Properly (COP) Module The COP counter is a free-running 6-bit counter preceded by the 12-bit SIM counter. If not cleared by software, the COP counter overflows and generates an asynchronous reset after 262,128 or 8176 CGMXCLK cycles, depending on the state of the COP rate select bit, COPRS, in the configuration register. With a 262,128 CGMXCLK cycle overflow option, a 4.9152-MHz crystal gives a COP timeout period of 53.3 ms. Writing any value to location $FFFF before an overflow occurs prevents a COP reset by clearing the COP counter and stages 12-5 of the SIM counter. NOTE Service the COP immediately after reset and before entering or after exiting stop mode to guarantee the maximum time before the first COP counter overflow. A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the COP bit in the reset status register (RSR). In monitor mode, the COP is disabled if the RST pin or the IRQ is held at VTST. During the break state, VTST on the RST pin disables the COP. NOTE Place COP clearing instructions in the main program and not in an interrupt subroutine. Such an interrupt subroutine could keep the COP from generating a reset even while the main program is not working properly. 6.3 I/O Signals The following paragraphs describe the signals shown in Figure 6-1. 6.3.1 CGMXCLK CGMXCLK is the crystal oscillator output signal. CGMXCLK frequency is equal to the crystal frequency. 6.3.2 STOP Instruction The STOP instruction clears the SIM counter. 6.3.3 COPCTL Write Writing any value to the COP control register (COPCTL) clears the COP counter and clears stages 12-5 of the SIM counter. Reading the COP control register returns the low byte of the reset vector. See 6.4 COP Control Register. 6.3.4 Power-On Reset The power-on reset (POR) circuit clears the SIM counter 4096 CGMXCLK cycles after power-up. 6.3.5 Internal Reset An internal reset clears the SIM counter and the COP counter. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 94 Freescale Semiconductor COP Control Register 6.3.6 COPD (COP Disable) The COPD signal reflects the state of the COP disable bit (COPD) in the configuration register. See Chapter 5 Configuration Register (CONFIG). 6.3.7 COPRS (COP Rate Select) The COPRS signal reflects the state of the COP rate select bit (COPRS) in the configuration register. See Chapter 5 Configuration Register (CONFIG). 6.4 COP Control Register The COP control register (COPCTL) is located at address $FFFF and overlaps the reset vector. Writing any value to $FFFF clears the COP counter and starts a new timeout period. Reading location $FFFF returns the low byte of the reset vector. Address: $FFFF Bit 7 6 5 4 3 Read: Low byte of reset vector Write: Clear COP counter Reset: Unaffected by reset 2 1 Bit 0 Figure 6-2. COP Control Register (COPCTL) 6.5 Interrupts The COP does not generate central processor unit (CPU) interrupt requests. 6.6 Monitor Mode When monitor mode is entered with VTST on the IRQ pin, the COP is disabled as long as VTST remains on the IRQ pin or the RST pin. When monitor mode is entered by having blank reset vectors and not having VTST on the IRQ pin, the COP is automatically disabled until a POR occurs. 6.7 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low power-consumption standby modes. 6.7.1 Wait Mode The COP remains active during wait mode. If COP is enabled, a reset will occur at COP timeout. 6.7.2 Stop Mode Stop mode turns off the CGMXCLK input to the COP and clears the SIM counter. Service the COP immediately before entering or after exiting stop mode to ensure a full COP timeout period after entering or exiting stop mode. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 95 Computer Operating Properly (COP) Module To prevent inadvertently turning off the COP with a STOP instruction, a configuration option is available that disables the STOP instruction. When the STOP bit in the configuration register has the STOP instruction disabled, execution of a STOP instruction results in an illegal opcode reset. 6.8 COP Module During Break Mode The COP is disabled during a break interrupt when VTST is present on the RST pin. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 96 Freescale Semiconductor Chapter 7 Central Processor Unit (CPU) 7.1 Introduction The M68HC08 CPU (central processor unit) is an enhanced and fully object-code-compatible version of the M68HC05 CPU. The CPU08 Reference Manual (document order number CPU08RM/AD) contains a description of the CPU instruction set, addressing modes, and architecture. 7.2 Features Features of the CPU include: * Object code fully upward-compatible with M68HC05 Family * 16-bit stack pointer with stack manipulation instructions * 16-bit index register with x-register manipulation instructions * 8-MHz CPU internal bus frequency * 64-Kbyte program/data memory space * 16 addressing modes * Memory-to-memory data moves without using accumulator * Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions * Enhanced binary-coded decimal (BCD) data handling * Modular architecture with expandable internal bus definition for extension of addressing range beyond 64 Kbytes * Low-power stop and wait modes 7.3 CPU Registers Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory map. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 97 Central Processor Unit (CPU) 0 7 ACCUMULATOR (A) 0 15 H X INDEX REGISTER (H:X) 15 0 STACK POINTER (SP) 15 0 PROGRAM COUNTER (PC) 7 0 V 1 1 H I N Z C CONDITION CODE REGISTER (CCR) CARRY/BORROW FLAG ZERO FLAG NEGATIVE FLAG INTERRUPT MASK HALF-CARRY FLAG TWO'S COMPLEMENT OVERFLOW FLAG Figure 7-1. CPU Registers 7.3.1 Accumulator The accumulator is a general-purpose 8-bit register. The CPU uses the accumulator to hold operands and the results of arithmetic/logic operations. Bit 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Unaffected by reset Figure 7-2. Accumulator (A) 7.3.2 Index Register The 16-bit index register allows indexed addressing of a 64-Kbyte memory space. H is the upper byte of the index register, and X is the lower byte. H:X is the concatenated 16-bit index register. In the indexed addressing modes, the CPU uses the contents of the index register to determine the conditional address of the operand. The index register can serve also as a temporary data storage location. Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 X X X X X X X X Read: Write: Reset: X = Indeterminate Figure 7-3. Index Register (H:X) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 98 Freescale Semiconductor CPU Registers 7.3.3 Stack Pointer The stack pointer is a 16-bit register that contains the address of the next location on the stack. During a reset, the stack pointer is preset to $00FF. The reset stack pointer (RSP) instruction sets the least significant byte to $FF and does not affect the most significant byte. The stack pointer decrements as data is pushed onto the stack and increments as data is pulled from the stack. In the stack pointer 8-bit offset and 16-bit offset addressing modes, the stack pointer can function as an index register to access data on the stack. The CPU uses the contents of the stack pointer to determine the conditional address of the operand. Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Read: Write: Reset: Figure 7-4. Stack Pointer (SP) NOTE The location of the stack is arbitrary and may be relocated anywhere in random-access memory (RAM). Moving the SP out of page 0 ($0000 to $00FF) frees direct address (page 0) space. For correct operation, the stack pointer must point only to RAM locations. 7.3.4 Program Counter The program counter is a 16-bit register that contains the address of the next instruction or operand to be fetched. Normally, the program counter automatically increments to the next sequential memory location every time an instruction or operand is fetched. Jump, branch, and interrupt operations load the program counter with an address other than that of the next sequential location. During reset, the program counter is loaded with the reset vector address located at $FFFE and $FFFF. The vector address is the address of the first instruction to be executed after exiting the reset state. Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Bit 0 Read: Write: Reset: Loaded with vector from $FFFE and $FFFF Figure 7-5. Program Counter (PC) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 99 Central Processor Unit (CPU) 7.3.5 Condition Code Register The 8-bit condition code register contains the interrupt mask and five flags that indicate the results of the instruction just executed. Bits 6 and 5 are set permanently to 1. The following paragraphs describe the functions of the condition code register. Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 V 1 1 H I N Z C X 1 1 X 1 X X X X = Indeterminate Figure 7-6. Condition Code Register (CCR) V -- Overflow Flag The CPU sets the overflow flag when a two's complement overflow occurs. The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag. 1 = Overflow 0 = No overflow H -- Half-Carry Flag The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C flags to determine the appropriate correction factor. 1 = Carry between bits 3 and 4 0 = No carry between bits 3 and 4 I -- Interrupt Mask When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set automatically after the CPU registers are saved on the stack, but before the interrupt vector is fetched. 1 = Interrupts disabled 0 = Interrupts enabled NOTE To maintain M6805 Family compatibility, the upper byte of the index register (H) is not stacked automatically. If the interrupt service routine modifies H, then the user must stack and unstack H using the PSHH and PULH instructions. After the I bit is cleared, the highest-priority interrupt request is serviced first. A return-from-interrupt (RTI) instruction pulls the CPU registers from the stack and restores the interrupt mask from the stack. After any reset, the interrupt mask is set and can be cleared only by the clear interrupt mask software instruction (CLI). N -- Negative Flag The CPU sets the negative flag when an arithmetic operation, logic operation, or data manipulation produces a negative result, setting bit 7 of the result. 1 = Negative result 0 = Non-negative result MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 100 Freescale Semiconductor Arithmetic/Logic Unit (ALU) Z -- Zero Flag The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation produces a result of $00. 1 = Zero result 0 = Non-zero result C -- Carry/Borrow Flag The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit 7 of the accumulator or when a subtraction operation requires a borrow. Some instructions -- such as bit test and branch, shift, and rotate -- also clear or set the carry/borrow flag. 1 = Carry out of bit 7 0 = No carry out of bit 7 7.4 Arithmetic/Logic Unit (ALU) The ALU performs the arithmetic and logic operations defined by the instruction set. Refer to the CPU08 Reference Manual (document order number CPU08RM/AD) for a description of the instructions and addressing modes and more detail about the architecture of the CPU. 7.5 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 7.5.1 Wait Mode The WAIT instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling interrupts. After exit from wait mode by interrupt, the I bit remains clear. After exit by reset, the I bit is set. * Disables the CPU clock 7.5.2 Stop Mode The STOP instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling external interrupts. After exit from stop mode by external interrupt, the I bit remains clear. After exit by reset, the I bit is set. * Disables the CPU clock After exiting stop mode, the CPU clock begins running after the oscillator stabilization delay. 7.6 CPU During Break Interrupts If a break module is present on the MCU, the CPU starts a break interrupt by: * Loading the instruction register with the SWI instruction * Loading the program counter with $FFFC:$FFFD or with $FEFC:$FEFD in monitor mode The break interrupt begins after completion of the CPU instruction in progress. If the break address register match occurs on the last cycle of a CPU instruction, the break interrupt begins immediately. A return-from-interrupt instruction (RTI) in the break routine ends the break interrupt and returns the MCU to normal operation if the break interrupt has been deasserted. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 101 Central Processor Unit (CPU) 7.7 Instruction Set Summary Table 7-1 provides a summary of the M68HC08 instruction set. ADC #opr ADC opr ADC opr ADC opr,X ADC opr,X ADC ,X ADC opr,SP ADC opr,SP ADD #opr ADD opr ADD opr ADD opr,X ADD opr,X ADD ,X ADD opr,SP ADD opr,SP V H I N Z C A (A) + (M) + (C) Add with Carry A (A) + (M) Add without Carry IMM DIR EXT IX2 - IX1 IX SP1 SP2 A9 B9 C9 D9 E9 F9 9EE9 9ED9 ii dd hh ll ee ff ff IMM DIR EXT - IX2 IX1 IX SP1 SP2 AB BB CB DB EB FB 9EEB 9EDB ii dd hh ll ee ff ff ff ee ff Cycles Effect on CCR Description Operand Operation Opcode Source Form Address Mode Table 7-1. Instruction Set Summary (Sheet 1 of 6) 2 3 4 4 3 2 4 5 ff ee ff 2 3 4 4 3 2 4 5 AIS #opr Add Immediate Value (Signed) to SP SP (SP) + (16 M) - - - - - - IMM A7 ii 2 AIX #opr Add Immediate Value (Signed) to H:X H:X (H:X) + (16 M) - - - - - - IMM AF ii 2 A (A) & (M) IMM DIR EXT IX2 0 - - - IX1 IX SP1 SP2 A4 B4 C4 D4 E4 F4 9EE4 9ED4 ii dd hh ll ee ff ff 2 3 4 4 3 2 4 5 0 DIR INH INH - - IX1 IX SP1 38 dd 48 58 68 ff 78 9E68 ff 4 1 1 4 3 5 C DIR INH - - INH IX1 IX SP1 37 dd 47 57 67 ff 77 9E67 ff 4 1 1 4 3 5 AND #opr AND opr AND opr AND opr,X AND opr,X AND ,X AND opr,SP AND opr,SP ASL opr ASLA ASLX ASL opr,X ASL ,X ASL opr,SP Logical AND Arithmetic Shift Left (Same as LSL) C b7 ASR opr ASRA ASRX ASR opr,X ASR opr,X ASR opr,SP Arithmetic Shift Right BCC rel Branch if Carry Bit Clear b0 b7 BCLR n, opr Clear Bit n in M b0 PC (PC) + 2 + rel ? (C) = 0 Mn 0 ff ee ff - - - - - - REL 24 rr 3 DIR (b0) DIR (b1) DIR (b2) - - - - - - DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 11 13 15 17 19 1B 1D 1F dd dd dd dd dd dd dd dd 4 4 4 4 4 4 4 4 BCS rel Branch if Carry Bit Set (Same as BLO) PC (PC) + 2 + rel ? (C) = 1 - - - - - - REL 25 rr 3 BEQ rel Branch if Equal PC (PC) + 2 + rel ? (Z) = 1 - - - - - - REL 27 rr 3 BGE opr Branch if Greater Than or Equal To (Signed Operands) PC (PC) + 2 + rel ? (N V) = 0 - - - - - - REL 90 rr 3 BGT opr Branch if Greater Than (Signed Operands) PC (PC) + 2 + rel ? (Z) | (N V) = 0 - - - - - - REL 92 rr 3 BHCC rel Branch if Half Carry Bit Clear PC (PC) + 2 + rel ? (H) = 0 - - - - - - REL 28 rr BHCS rel Branch if Half Carry Bit Set PC (PC) + 2 + rel ? (H) = 1 - - - - - - REL 29 rr BHI rel Branch if Higher PC (PC) + 2 + rel ? (C) | (Z) = 0 - - - - - - REL 22 rr 3 3 3 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 102 Freescale Semiconductor Instruction Set Summary Effect on CCR V H I N Z C BHS rel Branch if Higher or Same (Same as BCC) BIH rel BIL rel PC (PC) + 2 + rel ? (C) = 0 - - - - - - REL Branch if IRQ Pin High PC (PC) + 2 + rel ? IRQ = 1 Branch if IRQ Pin Low PC (PC) + 2 + rel ? IRQ = 0 (A) & (M) BIT #opr BIT opr BIT opr BIT opr,X BIT opr,X BIT ,X BIT opr,SP BIT opr,SP Bit Test BLE opr Branch if Less Than or Equal To (Signed Operands) Cycles Description Operand Operation Opcode Source Form Address Mode Table 7-1. Instruction Set Summary (Sheet 2 of 6) 24 rr 3 - - - - - - REL 2F rr 3 - - - - - - REL 2E rr 3 IMM DIR EXT 0 - - - IX2 IX1 IX SP1 SP2 A5 B5 C5 D5 E5 F5 9EE5 9ED5 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 rr 3 PC (PC) + 2 + rel ? (Z) | (N V) = 1 - - - - - - REL 93 BLO rel Branch if Lower (Same as BCS) PC (PC) + 2 + rel ? (C) = 1 - - - - - - REL 25 rr 3 BLS rel Branch if Lower or Same PC (PC) + 2 + rel ? (C) | (Z) = 1 - - - - - - REL 23 rr 3 BLT opr Branch if Less Than (Signed Operands) PC (PC) + 2 + rel ? (N V) =1 - - - - - - REL 91 rr 3 BMC rel Branch if Interrupt Mask Clear PC (PC) + 2 + rel ? (I) = 0 - - - - - - REL 2C rr 3 BMI rel Branch if Minus PC (PC) + 2 + rel ? (N) = 1 - - - - - - REL 2B rr 3 BMS rel Branch if Interrupt Mask Set PC (PC) + 2 + rel ? (I) = 1 - - - - - - REL 2D rr 3 3 BNE rel Branch if Not Equal PC (PC) + 2 + rel ? (Z) = 0 - - - - - - REL 26 rr BPL rel Branch if Plus PC (PC) + 2 + rel ? (N) = 0 - - - - - - REL 2A rr 3 BRA rel Branch Always PC (PC) + 2 + rel - - - - - - REL 20 rr 3 DIR (b0) DIR (b1) DIR (b2) DIR (b3) - - - - - DIR (b4) DIR (b5) DIR (b6) DIR (b7) 01 03 05 07 09 0B 0D 0F dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr 5 5 5 5 5 5 5 5 BRCLR n,opr,rel Branch if Bit n in M Clear BRN rel Branch Never BRSET n,opr,rel Branch if Bit n in M Set BSET n,opr Set Bit n in M BSR rel Branch to Subroutine CBEQ opr,rel CBEQA #opr,rel CBEQX #opr,rel Compare and Branch if Equal CBEQ opr,X+,rel CBEQ X+,rel CBEQ opr,SP,rel PC (PC) + 3 + rel ? (Mn) = 0 PC (PC) + 2 - - - - - - REL 21 rr 3 PC (PC) + 3 + rel ? (Mn) = 1 DIR (b0) DIR (b1) DIR (b2) DIR (b3) - - - - - DIR (b4) DIR (b5) DIR (b6) DIR (b7) 00 02 04 06 08 0A 0C 0E dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr 5 5 5 5 5 5 5 5 Mn 1 DIR (b0) DIR (b1) DIR (b2) - - - - - - DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 10 12 14 16 18 1A 1C 1E dd dd dd dd dd dd dd dd 4 4 4 4 4 4 4 4 PC (PC) + 2; push (PCL) SP (SP) - 1; push (PCH) SP (SP) - 1 PC (PC) + rel - - - - - - REL AD rr 4 PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 3 + rel ? (X) - (M) = $00 PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 2 + rel ? (A) - (M) = $00 PC (PC) + 4 + rel ? (A) - (M) = $00 DIR IMM - - - - - - IMM IX1+ IX+ SP1 31 41 51 61 71 9E61 dd rr ii rr ii rr ff rr rr ff rr 5 4 4 5 4 6 CLC Clear Carry Bit C0 - - - - - 0 INH 98 1 CLI Clear Interrupt Mask I0 - - 0 - - - INH 9A 2 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 103 Central Processor Unit (CPU) CLR opr CLRA CLRX CLRH CLR opr,X CLR ,X CLR opr,SP CMP #opr CMP opr CMP opr CMP opr,X CMP opr,X CMP ,X CMP opr,SP CMP opr,SP Clear Compare A with M Complement (One's Complement) CPHX #opr CPHX opr Compare H:X with M CPX #opr CPX opr CPX opr CPX ,X CPX opr,X CPX opr,X CPX opr,SP CPX opr,SP Compare X with M DAA Decimal Adjust A DBNZ opr,rel DBNZA rel DBNZX rel Decrement and Branch if Not Zero DBNZ opr,X,rel DBNZ X,rel DBNZ opr,SP,rel DEC opr DECA DECX DEC opr,X DEC ,X DEC opr,SP Decrement DIV Divide INC opr INCA INCX INC opr,X INC ,X INC opr,SP Exclusive OR M with A Increment M $00 A $00 X $00 H $00 M $00 M $00 M $00 DIR INH INH 0 - - 0 1 - INH IX1 IX SP1 3F dd 4F 5F 8C 6F ff 7F 9E6F ff (A) - (M) IMM DIR EXT IX2 - - IX1 IX SP1 SP2 A1 B1 C1 D1 E1 F1 9EE1 9ED1 DIR INH INH 0 - - 1 IX1 IX SP1 33 dd 43 53 63 ff 73 9E63 ff M (M) = $FF - (M) A (A) = $FF - (M) X (X) = $FF - (M) M (M) = $FF - (M) M (M) = $FF - (M) M (M) = $FF - (M) (H:X) - (M:M + 1) (X) - (M) (A)10 ff ee ff 2 3 4 4 3 2 4 5 4 1 1 4 3 5 ii ii+1 dd 3 4 IMM DIR EXT IX2 - - IX1 IX SP1 SP2 A3 B3 C3 D3 E3 F3 9EE3 9ED3 ii dd hh ll ee ff ff 2 3 4 4 3 2 4 5 U - - INH 72 A (A) - 1 or M (M) - 1 or X (X) - 1 PC (PC) + 3 + rel ? (result) 0 DIR PC (PC) + 2 + rel ? (result) 0 INH PC (PC) + 2 + rel ? (result) 0 - - - - - - INH PC (PC) + 3 + rel ? (result) 0 IX1 PC (PC) + 2 + rel ? (result) 0 IX PC (PC) + 4 + rel ? (result) 0 SP1 3B 4B 5B 6B 7B 9E6B ff ee ff 2 dd rr rr rr ff rr rr ff rr M (M) - 1 A (A) - 1 X (X) - 1 M (M) - 1 M (M) - 1 M (M) - 1 DIR INH INH - - - IX1 IX SP1 A (H:A)/(X) H Remainder - - - - INH 52 A (A M) IMM DIR EXT 0 - - - IX2 IX1 IX SP1 SP2 A8 B8 C8 D8 E8 F8 9EE8 9ED8 DIR INH - - - INH IX1 IX SP1 3C dd 4C 5C 6C ff 7C 9E6C ff M (M) + 1 A (A) + 1 X (X) + 1 M (M) + 1 M (M) + 1 M (M) + 1 3 1 1 1 3 2 4 65 75 - - IMM DIR ii dd hh ll ee ff ff Cycles Effect on CCR V H I N Z C COM opr COMA COMX COM opr,X COM ,X COM opr,SP EOR #opr EOR opr EOR opr EOR opr,X EOR opr,X EOR ,X EOR opr,SP EOR opr,SP Description Operand Operation Opcode Source Form Address Mode Table 7-1. Instruction Set Summary (Sheet 3 of 6) 3A dd 4A 5A 6A ff 7A 9E6A ff 5 3 3 5 4 6 4 1 1 4 3 5 7 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 4 1 1 4 3 5 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 104 Freescale Semiconductor Instruction Set Summary JSR opr JSR opr JSR opr,X JSR opr,X JSR ,X Jump to Subroutine LDHX #opr LDHX opr Load H:X from M 2 3 4 3 2 PC (PC) + n (n = 1, 2, or 3) Push (PCL); SP (SP) - 1 Push (PCH); SP (SP) - 1 PC Unconditional Address DIR EXT - - - - - - IX2 IX1 IX BD CD DD ED FD dd hh ll ee ff ff 4 5 6 5 4 A (M) IMM DIR EXT IX2 0 - - - IX1 IX SP1 SP2 A6 B6 C6 D6 E6 F6 9EE6 9ED6 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 ii jj dd 3 4 ii dd hh ll ee ff ff 2 3 4 4 3 2 4 5 H:X (M:M + 1) Logical Shift Left (Same as ASL) Logical Shift Right MOV opr,opr MOV opr,X+ MOV #opr,opr MOV X+,opr Move MUL Unsigned multiply C b7 45 55 AE BE CE DE EE FE 9EEE 9EDE 0 DIR INH INH - - IX1 IX SP1 38 dd 48 58 68 ff 78 9E68 ff 4 1 1 4 3 5 C DIR INH - - 0 INH IX1 IX SP1 34 dd 44 54 64 ff 74 9E64 ff 4 1 1 4 3 5 b0 0 IMM DIR IMM DIR EXT IX2 0 - - - IX1 IX SP1 SP2 X (M) b7 Negate (Two's Complement) 0 - - - b0 H:X (H:X) + 1 (IX+D, DIX+) DD DIX+ 0 - - - IMD IX+D X:A (X) x (A) - 0 - - - 0 INH M -(M) = $00 - (M) A -(A) = $00 - (A) X -(X) = $00 - (X) M -(M) = $00 - (M) M -(M) = $00 - (M) DIR INH INH - - IX1 IX SP1 (M)Destination (M)Source 4E 5E 6E 7E dd dd dd ii dd dd 42 No Operation None - - - - - - INH 9D NSA Nibble Swap A A (A[3:0]:A[7:4]) - - - - - - INH 62 A (A) | (M) IMM DIR EXT IX2 0 - - - IX1 IX SP1 SP2 AA BA CA DA EA FA 9EEA 9EDA Inclusive OR A and M ff ee ff 5 4 4 4 5 30 dd 40 50 60 ff 70 9E60 ff NOP ORA #opr ORA opr ORA opr ORA opr,X ORA opr,X ORA ,X ORA opr,SP ORA opr,SP Cycles dd hh ll ee ff ff Load X from M LSR opr LSRA LSRX LSR opr,X LSR ,X LSR opr,SP NEG opr NEGA NEGX NEG opr,X NEG ,X NEG opr,SP BC CC DC EC FC Jump Load A from M LSL opr LSLA LSLX LSL opr,X LSL ,X LSL opr,SP PC Jump Address DIR EXT - - - - - - IX2 IX1 IX Effect on CCR Description V H I N Z C LDA #opr LDA opr LDA opr LDA opr,X LDA opr,X LDA ,X LDA opr,SP LDA opr,SP LDX #opr LDX opr LDX opr LDX opr,X LDX opr,X LDX ,X LDX opr,SP LDX opr,SP Operand JMP opr JMP opr JMP opr,X JMP opr,X JMP ,X Operation Address Mode Source Form Opcode Table 7-1. Instruction Set Summary (Sheet 4 of 6) 4 1 1 4 3 5 1 3 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 PSHA Push A onto Stack Push (A); SP (SP) - 1 - - - - - - INH 87 2 PSHH Push H onto Stack Push (H); SP (SP) - 1 - - - - - - INH 8B 2 PSHX Push X onto Stack Push (X); SP (SP) - 1 - - - - - - INH 89 2 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 105 Central Processor Unit (CPU) V H I N Z C Cycles Effect on CCR Description Operand Operation Opcode Source Form Address Mode Table 7-1. Instruction Set Summary (Sheet 5 of 6) PULA Pull A from Stack SP (SP + 1); Pull (A) - - - - - - INH 86 2 PULH Pull H from Stack SP (SP + 1); Pull (H) - - - - - - INH 8A 2 PULX Pull X from Stack SP (SP + 1); Pull (X) - - - - - - INH C DIR INH INH - - IX1 IX SP1 39 dd 49 59 69 ff 79 9E69 ff 4 1 1 4 3 5 DIR INH - - INH IX1 IX SP1 36 dd 46 56 66 ff 76 9E66 ff 4 1 1 4 3 5 ROL opr ROLA ROLX ROL opr,X ROL ,X ROL opr,SP Rotate Left through Carry b7 b0 88 2 ROR opr RORA RORX ROR opr,X ROR ,X ROR opr,SP Rotate Right through Carry RSP Reset Stack Pointer SP $FF - - - - - - INH 9C 1 RTI Return from Interrupt SP (SP) + 1; Pull (CCR) SP (SP) + 1; Pull (A) SP (SP) + 1; Pull (X) SP (SP) + 1; Pull (PCH) SP (SP) + 1; Pull (PCL) INH 80 7 RTS Return from Subroutine SP SP + 1; Pull (PCH) SP SP + 1; Pull (PCL) - - - - - - INH 81 4 A (A) - (M) - (C) IMM DIR EXT - - IX2 IX1 IX SP1 SP2 A2 B2 C2 D2 E2 F2 9EE2 9ED2 SBC #opr SBC opr SBC opr SBC opr,X SBC opr,X SBC ,X SBC opr,SP SBC opr,SP C b7 Subtract with Carry b0 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 SEC Set Carry Bit C1 - - - - - 1 INH 99 1 SEI Set Interrupt Mask I1 - - 1 - - - INH 9B 2 M (A) DIR EXT IX2 0 - - - IX1 IX SP1 SP2 B7 C7 D7 E7 F7 9EE7 9ED7 (M:M + 1) (H:X) 0 - - - DIR 35 I 0; Stop Processing - - 0 - - - INH 8E M (X) DIR EXT IX2 0 - - - IX1 IX SP1 SP2 BF CF DF EF FF 9EEF 9EDF dd hh ll ee ff ff IMM DIR EXT - - IX2 IX1 IX SP1 SP2 A0 B0 C0 D0 E0 F0 9EE0 9ED0 ii dd hh ll ee ff ff STA opr STA opr STA opr,X STA opr,X STA ,X STA opr,SP STA opr,SP Store A in M STHX opr Store H:X in M STOP Enable Interrupts, Stop Processing, Refer to MCU Documentation STX opr STX opr STX opr,X STX opr,X STX ,X STX opr,SP STX opr,SP SUB #opr SUB opr SUB opr SUB opr,X SUB opr,X SUB ,X SUB opr,SP SUB opr,SP Store X in M Subtract A (A) - (M) dd hh ll ee ff ff ff ee ff 3 4 4 3 2 4 5 dd 4 1 ff ee ff ff ee ff 3 4 4 3 2 4 5 2 3 4 4 3 2 4 5 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 106 Freescale Semiconductor Opcode Map SWI Software Interrupt PC (PC) + 1; Push (PCL) SP (SP) - 1; Push (PCH) SP (SP) - 1; Push (X) SP (SP) - 1; Push (A) SP (SP) - 1; Push (CCR) SP (SP) - 1; I 1 PCH Interrupt Vector High Byte PCL Interrupt Vector Low Byte - - 1 - - - INH 83 9 CCR (A) INH 84 2 X (A) - - - - - - INH 97 1 A (CCR) - - - - - - INH 85 (A) - $00 or (X) - $00 or (M) - $00 DIR INH INH 0 - - - IX1 IX SP1 H:X (SP) + 1 - - - - - - INH 95 2 A (X) - - - - - - INH 9F 1 (SP) (H:X) - 1 - - - - - - INH 94 2 I bit 0; Inhibit CPU clocking until interrupted - - 0 - - - INH 8F 1 TAP Transfer A to CCR Transfer A to X TPA Transfer CCR to A Test for Negative or Zero TSX Transfer SP to H:X TXA Transfer X to A TXS Transfer H:X to SP WAIT A C CCR dd dd rr DD DIR DIX+ ee ff EXT ff H H hh ll I ii IMD IMM INH IX IX+ IX+D IX1 IX1+ IX2 M N Cycles V H I N Z C TAX TST opr TSTA TSTX TST opr,X TST ,X TST opr,SP Effect on CCR Description Operand Operation Opcode Source Form Address Mode Table 7-1. Instruction Set Summary (Sheet 6 of 6) Enable Interrupts; Wait for Interrupt Accumulator Carry/borrow bit Condition code register Direct address of operand Direct address of operand and relative offset of branch instruction Direct to direct addressing mode Direct addressing mode Direct to indexed with post increment addressing mode High and low bytes of offset in indexed, 16-bit offset addressing Extended addressing mode Offset byte in indexed, 8-bit offset addressing Half-carry bit Index register high byte High and low bytes of operand address in extended addressing Interrupt mask Immediate operand byte Immediate source to direct destination addressing mode Immediate addressing mode Inherent addressing mode Indexed, no offset addressing mode Indexed, no offset, post increment addressing mode Indexed with post increment to direct addressing mode Indexed, 8-bit offset addressing mode Indexed, 8-bit offset, post increment addressing mode Indexed, 16-bit offset addressing mode Memory location Negative bit n opr PC PCH PCL REL rel rr SP1 SP2 SP U V X Z & | () -( ) # ? : -- 3D dd 4D 5D 6D ff 7D 9E6D ff 1 3 1 1 3 2 4 Any bit Operand (one or two bytes) Program counter Program counter high byte Program counter low byte Relative addressing mode Relative program counter offset byte Relative program counter offset byte Stack pointer, 8-bit offset addressing mode Stack pointer 16-bit offset addressing mode Stack pointer Undefined Overflow bit Index register low byte Zero bit Logical AND Logical OR Logical EXCLUSIVE OR Contents of Negation (two's complement) Immediate value Sign extend Loaded with If Concatenated with Set or cleared Not affected 7.8 Opcode Map See Table 7-2. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 107 MSB Branch REL DIR INH 3 4 0 1 2 5 BRSET0 3 DIR 5 BRCLR0 3 DIR 5 BRSET1 3 DIR 5 BRCLR1 3 DIR 5 BRSET2 3 DIR 5 BRCLR2 3 DIR 5 BRSET3 3 DIR 5 BRCLR3 3 DIR 5 BRSET4 3 DIR 5 BRCLR4 3 DIR 5 BRSET5 3 DIR 5 BRCLR5 3 DIR 5 BRSET6 3 DIR 5 BRCLR6 3 DIR 5 BRSET7 3 DIR 5 BRCLR7 3 DIR 4 BSET0 2 DIR 4 BCLR0 2 DIR 4 BSET1 2 DIR 4 BCLR1 2 DIR 4 BSET2 2 DIR 4 BCLR2 2 DIR 4 BSET3 2 DIR 4 BCLR3 2 DIR 4 BSET4 2 DIR 4 BCLR4 2 DIR 4 BSET5 2 DIR 4 BCLR5 2 DIR 4 BSET6 2 DIR 4 BCLR6 2 DIR 4 BSET7 2 DIR 4 BCLR7 2 DIR 3 BRA 2 REL 3 BRN 2 REL 3 BHI 2 REL 3 BLS 2 REL 3 BCC 2 REL 3 BCS 2 REL 3 BNE 2 REL 3 BEQ 2 REL 3 BHCC 2 REL 3 BHCS 2 REL 3 BPL 2 REL 3 BMI 2 REL 3 BMC 2 REL 3 BMS 2 REL 3 BIL 2 REL 3 BIH 2 REL Read-Modify-Write INH IX1 5 6 1 NEGX 1 INH 4 CBEQX 3 IMM 7 DIV 1 INH 1 COMX 1 INH 1 LSRX 1 INH 4 LDHX 2 DIR 1 RORX 1 INH 1 ASRX 1 INH 1 LSLX 1 INH 1 ROLX 1 INH 1 DECX 1 INH 3 DBNZX 2 INH 1 INCX 1 INH 1 TSTX 1 INH 4 MOV 2 DIX+ 1 CLRX 1 INH 4 NEG 2 IX1 5 CBEQ 3 IX1+ 3 NSA 1 INH 4 COM 2 IX1 4 LSR 2 IX1 3 CPHX 3 IMM 4 ROR 2 IX1 4 ASR 2 IX1 4 LSL 2 IX1 4 ROL 2 IX1 4 DEC 2 IX1 5 DBNZ 3 IX1 4 INC 2 IX1 3 TST 2 IX1 4 MOV 3 IMD 3 CLR 2 IX1 SP1 IX 9E6 7 Control INH INH 8 9 Register/Memory IX2 SP2 IMM DIR EXT A B C D 9ED 4 SUB 3 EXT 4 CMP 3 EXT 4 SBC 3 EXT 4 CPX 3 EXT 4 AND 3 EXT 4 BIT 3 EXT 4 LDA 3 EXT 4 STA 3 EXT 4 EOR 3 EXT 4 ADC 3 EXT 4 ORA 3 EXT 4 ADD 3 EXT 3 JMP 3 EXT 5 JSR 3 EXT 4 LDX 3 EXT 4 STX 3 EXT 4 SUB 3 IX2 4 CMP 3 IX2 4 SBC 3 IX2 4 CPX 3 IX2 4 AND 3 IX2 4 BIT 3 IX2 4 LDA 3 IX2 4 STA 3 IX2 4 EOR 3 IX2 4 ADC 3 IX2 4 ORA 3 IX2 4 ADD 3 IX2 4 JMP 3 IX2 6 JSR 3 IX2 4 LDX 3 IX2 4 STX 3 IX2 5 SUB 4 SP2 5 CMP 4 SP2 5 SBC 4 SP2 5 CPX 4 SP2 5 AND 4 SP2 5 BIT 4 SP2 5 LDA 4 SP2 5 STA 4 SP2 5 EOR 4 SP2 5 ADC 4 SP2 5 ORA 4 SP2 5 ADD 4 SP2 IX1 SP1 IX E 9EE F LSB 0 Freescale Semiconductor MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 1 2 3 4 5 6 7 8 9 A B C D E F 4 1 NEG NEGA 2 DIR 1 INH 5 4 CBEQ CBEQA 3 DIR 3 IMM 5 MUL 1 INH 4 1 COM COMA 2 DIR 1 INH 4 1 LSR LSRA 2 DIR 1 INH 4 3 STHX LDHX 2 DIR 3 IMM 4 1 ROR RORA 2 DIR 1 INH 4 1 ASR ASRA 2 DIR 1 INH 4 1 LSL LSLA 2 DIR 1 INH 4 1 ROL ROLA 2 DIR 1 INH 4 1 DEC DECA 2 DIR 1 INH 5 3 DBNZ DBNZA 3 DIR 2 INH 4 1 INC INCA 2 DIR 1 INH 3 1 TST TSTA 2 DIR 1 INH 5 MOV 3 DD 3 1 CLR CLRA 2 DIR 1 INH INH Inherent REL Relative IMM Immediate IX Indexed, No Offset DIR Direct IX1 Indexed, 8-Bit Offset EXT Extended IX2 Indexed, 16-Bit Offset DD Direct-Direct IMD Immediate-Direct IX+D Indexed-Direct DIX+ Direct-Indexed *Pre-byte for stack pointer indexed instructions 5 3 NEG NEG 3 SP1 1 IX 6 4 CBEQ CBEQ 4 SP1 2 IX+ 2 DAA 1 INH 5 3 COM COM 3 SP1 1 IX 5 3 LSR LSR 3 SP1 1 IX 4 CPHX 2 DIR 5 3 ROR ROR 3 SP1 1 IX 5 3 ASR ASR 3 SP1 1 IX 5 3 LSL LSL 3 SP1 1 IX 5 3 ROL ROL 3 SP1 1 IX 5 3 DEC DEC 3 SP1 1 IX 6 4 DBNZ DBNZ 4 SP1 2 IX 5 3 INC INC 3 SP1 1 IX 4 2 TST TST 3 SP1 1 IX 4 MOV 2 IX+D 4 2 CLR CLR 3 SP1 1 IX SP1 Stack Pointer, 8-Bit Offset SP2 Stack Pointer, 16-Bit Offset IX+ Indexed, No Offset with Post Increment IX1+ Indexed, 1-Byte Offset with Post Increment 7 3 RTI BGE 1 INH 2 REL 4 3 RTS BLT 1 INH 2 REL 3 BGT 2 REL 9 3 SWI BLE 1 INH 2 REL 2 2 TAP TXS 1 INH 1 INH 1 2 TPA TSX 1 INH 1 INH 2 PULA 1 INH 2 1 PSHA TAX 1 INH 1 INH 2 1 PULX CLC 1 INH 1 INH 2 1 PSHX SEC 1 INH 1 INH 2 2 PULH CLI 1 INH 1 INH 2 2 PSHH SEI 1 INH 1 INH 1 1 CLRH RSP 1 INH 1 INH 1 NOP 1 INH 1 STOP * 1 INH 1 1 WAIT TXA 1 INH 1 INH 2 SUB 2 IMM 2 CMP 2 IMM 2 SBC 2 IMM 2 CPX 2 IMM 2 AND 2 IMM 2 BIT 2 IMM 2 LDA 2 IMM 2 AIS 2 IMM 2 EOR 2 IMM 2 ADC 2 IMM 2 ORA 2 IMM 2 ADD 2 IMM 3 SUB 2 DIR 3 CMP 2 DIR 3 SBC 2 DIR 3 CPX 2 DIR 3 AND 2 DIR 3 BIT 2 DIR 3 LDA 2 DIR 3 STA 2 DIR 3 EOR 2 DIR 3 ADC 2 DIR 3 ORA 2 DIR 3 ADD 2 DIR 2 JMP 2 DIR 4 4 BSR JSR 2 REL 2 DIR 2 3 LDX LDX 2 IMM 2 DIR 2 3 AIX STX 2 IMM 2 DIR MSB 0 3 SUB 2 IX1 3 CMP 2 IX1 3 SBC 2 IX1 3 CPX 2 IX1 3 AND 2 IX1 3 BIT 2 IX1 3 LDA 2 IX1 3 STA 2 IX1 3 EOR 2 IX1 3 ADC 2 IX1 3 ORA 2 IX1 3 ADD 2 IX1 3 JMP 2 IX1 5 JSR 2 IX1 5 3 LDX LDX 4 SP2 2 IX1 5 3 STX STX 4 SP2 2 IX1 4 SUB 3 SP1 4 CMP 3 SP1 4 SBC 3 SP1 4 CPX 3 SP1 4 AND 3 SP1 4 BIT 3 SP1 4 LDA 3 SP1 4 STA 3 SP1 4 EOR 3 SP1 4 ADC 3 SP1 4 ORA 3 SP1 4 ADD 3 SP1 2 SUB 1 IX 2 CMP 1 IX 2 SBC 1 IX 2 CPX 1 IX 2 AND 1 IX 2 BIT 1 IX 2 LDA 1 IX 2 STA 1 IX 2 EOR 1 IX 2 ADC 1 IX 2 ORA 1 IX 2 ADD 1 IX 2 JMP 1 IX 4 JSR 1 IX 4 2 LDX LDX 3 SP1 1 IX 4 2 STX STX 3 SP1 1 IX High Byte of Opcode in Hexadecimal LSB Low Byte of Opcode in Hexadecimal 0 5 Cycles BRSET0 Opcode Mnemonic 3 DIR Number of Bytes / Addressing Mode Central Processor Unit (CPU) 108 Table 7-2. Opcode Map Bit Manipulation DIR DIR Chapter 8 External Interrupt (IRQ) 8.1 Introduction The IRQ (external interrupt) module provides a maskable interrupt input. 8.2 Features * * * * * * * Features of the IRQ module include: A dedicated external interrupt pin (IRQ) IRQ interrupt control bits Hysteresis buffer Programmable edge-only or edge and level interrupt sensitivity Automatic interrupt acknowledge Internal pullup resistor 8.3 Functional Description A low applied to the external interrupt pin can latch a central processor unit (CPU) interrupt request. Figure 8-1 shows the structure of the IRQ module. Interrupt signals on the IRQ pin are latched into the IRQ latch. An interrupt latch remains set until one of the following actions occurs: * Vector fetch -- A vector fetch automatically generates an interrupt acknowledge signal that clears the latch that caused the vector fetch. * Software clear -- Software can clear an interrupt latch by writing to the appropriate acknowledge bit in the interrupt status and control register (INTSCR). Writing a 1 to the ACK bit clears the IRQ latch. * Reset -- A reset automatically clears the interrupt latch. The external interrupt pin is falling-edge triggered out of reset and is software-configurable to be either falling-edge or falling-edge and low-level triggered. The MODE bit in the INTSCR controls the triggering sensitivity of the IRQ pin. When an interrupt pin is edge-triggered only (MODE = 0), the interrupt remains set until a vector fetch, software clear, or reset occurs. When an interrupt pin is both falling-edge and low-level triggered (MODE = 1), the interrupt remains set until both of these events occur: * Vector fetch or software clear * Return of the interrupt pin to a high level MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 109 External Interrupt (IRQ) RESET ACK TO CPU FOR BIL/BIH INSTRUCTIONS INTERNAL ADDRESS BUS VECTOR FETCH DECODER VDD INTERNAL PULLUP DEVICE VDD IRQF D CLR Q IRQ INTERRUPT REQUEST SYNCHRONIZER CK IRQ IMASK MODE TO MODE SELECT LOGIC HIGH VOLTAGE DETECT Figure 8-1. IRQ Module Block Diagram The vector fetch or software clear may occur before or after the interrupt pin returns to a high level. As long as the pin is low, the interrupt request remains pending. A reset will clear the latch and the MODE control bit, thereby clearing the interrupt even if the pin stays low. When set, the IMASK bit in the INTSCR masks all external interrupt requests. A latched interrupt request is not presented to the interrupt priority logic unless the IMASK bit is clear. NOTE The interrupt mask (I) in the condition code register (CCR) masks all interrupt requests, including external interrupt requests. Addr. Register Name $001D IRQ Status and Control Read: Register (INTSCR) Write: See page 112. Reset: Bit 7 6 5 4 3 2 0 0 0 0 IRQF 0 ACK 0 0 0 0 0 0 1 Bit 0 IMASK MODE 0 0 = Unimplemented Figure 8-2. IRQ I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 110 Freescale Semiconductor IRQ Pin 8.4 IRQ Pin A falling edge on the IRQ pin can latch an interrupt request into the IRQ latch. A vector fetch, software clear, or reset clears the IRQ latch. If the MODE bit is set, the IRQ pin is both falling-edge-sensitive and low-level-sensitive. With MODE set, both of the following actions must occur to clear IRQ: * Vector fetch or software clear -- A vector fetch generates an interrupt acknowledge signal to clear the latch. Software may generate the interrupt acknowledge signal by writing a 1 to the ACK bit in the interrupt status and control register (INTSCR). The ACK bit is useful in applications that poll the IRQ pin and require software to clear the IRQ latch. Writing to the ACK bit prior to leaving an interrupt service routine can also prevent spurious interrupts due to noise. Setting ACK does not affect subsequent transitions on the IRQ pin. A falling edge that occurs after writing to the ACK bit latches another interrupt request. If the IRQ mask bit, IMASK, is clear, the CPU loads the program counter with the vector address at locations $FFFA and $FFFB. * Return of the IRQ pin to a high level -- As long as the IRQ pin is low, IRQ remains active. The vector fetch or software clear and the return of the IRQ pin to a high level may occur in any order. The interrupt request remains pending as long as the IRQ pin is low. A reset will clear the latch and the MODE control bit, thereby clearing the interrupt even if the pin stays low. If the MODE bit is clear, the IRQ pin is falling-edge-sensitive only. With MODE clear, a vector fetch or software clear immediately clears the IRQ latch. The IRQF bit in the INTSCR register can be used to check for pending interrupts. The IRQF bit is not affected by the IMASK bit, which makes it useful in applications where polling is preferred. Use the BIH or BIL instruction to read the logic level on the IRQ pin. NOTE When using the level-sensitive interrupt trigger, avoid false interrupts by masking interrupt requests in the interrupt routine. 8.5 IRQ Module During Break Interrupts The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear the latch during the break state. See Chapter 19 Development Support. To allow software to clear the IRQ latch during a break interrupt, write a 1 to the BCFE bit. If a latch is cleared during the break state, it remains cleared when the MCU exits the break state. To protect CPU interrupt flags during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), writing to the ACK bit in the IRQ status and control register during the break state has no effect on the IRQ interrupt flags. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 111 External Interrupt (IRQ) 8.6 IRQ Status and Control Register The IRQ status and control register (INTSCR) controls and monitors operation of the IRQ module. The INTSCR: * Shows the state of the IRQ flag * Clears the IRQ latch * Masks IRQ interrupt request * Controls triggering sensitivity of the IRQ interrupt pin Address: Read: $001D Bit 7 6 5 4 3 2 0 0 0 0 IRQF 0 Write: Reset: ACK 0 0 0 0 0 0 1 Bit 0 IMASK MODE 0 0 = Unimplemented Figure 8-3. IRQ Status and Control Register (INTSCR) IRQF -- IRQ Flag Bit This read-only status bit is high when the IRQ interrupt is pending. 1 = IRQ interrupt pending 0 = IRQ interrupt not pending ACK -- IRQ Interrupt Request Acknowledge Bit Writing a 1 to this write-only bit clears the IRQ latch. ACK always reads as 0. Reset clears ACK. IMASK -- IRQ Interrupt Mask Bit Writing a 1 to this read/write bit disables IRQ interrupt requests. Reset clears IMASK. 1 = IRQ interrupt requests disabled 0 = IRQ interrupt requests enabled MODE -- IRQ Edge/Level Select Bit This read/write bit controls the triggering sensitivity of the IRQ pin. Reset clears MODE. 1 = IRQ interrupt requests on falling edges and low levels 0 = IRQ interrupt requests on falling edges only MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 112 Freescale Semiconductor Chapter 9 Keyboard Interrupt Module (KBI) 9.1 Introduction The keyboard interrupt module (KBI) provides eight independently maskable external interrupts which are accessible via PTA0-PTA7. When a port pin is enabled for keyboard interrupt function, an internal pullup/pulldown device is also enabled on the pin. 9.2 Features Features include: * Eight keyboard interrupt pins with separate keyboard interrupt enable bits and one keyboard interrupt mask * Hysteresis buffers * Programmable edge-only or edge- and level- interrupt sensitivity * Edge detect programmable for rising or falling edges * Level detect programmable for high or low levels * Exit from low-power modes * Pullup/pulldown device automatically configured based on polarity of edge/level selection 9.3 Functional Description Writing to the KBIE7-KBIE0 bits in the keyboard interrupt enable register independently enables or disables each port A pin as a keyboard interrupt pin. Enabling a keyboard interrupt pin also enables its internal pullup/pulldown device. On falling edge or low level selection a pullup device is configured. On rising edge or high level selection a pulldown device is configured. * A falling edge is detected when an enabled keyboard input signal is seen as a 1 (the deasserted level) during one bus cycle and then a 0 (the asserted level) during the next cycle. * A rising edge is detected when the input signal is seen as a 0 during one bus cycle and then a 1 during the next cycle. A keyboard interrupt is latched when one or more keyboard pins are asserted. The MODEK bit in the keyboard status and control register controls the triggering mode of the keyboard interrupt. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 113 Keyboard Interrupt Module (KBI) INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 9-1. Block Diagram Highlighting KBI Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 114 Freescale Semiconductor Functional Description The KBIP7-KBIP0 bits determine the polarity of the keyboard pin detection. These bits along with the MODEK bit determine whether a logic level (0 or 1) and/or a falling (or rising) edge is being detected. * If the keyboard interrupt is edge-sensitive only, a falling (or rising) edge on a keyboard pin does not latch an interrupt request if another keyboard pin is already asserted. To prevent losing an interrupt request on one pin because another pin is still asserted, software can disable the latter pin while it is asserted. * If the keyboard interrupt is edge and level sensitive, an interrupt request is present as long as any keyboard interrupt pin is asserted and the pin is keyboard interrupt enabled. INTERNAL BUS VECTOR FETCH DECODER ACKK RESET 1 KBD0 0S VDD KBIE0 TO PULLUP/ PULLDOWN ENABLE KBIP0 KEYF D CLR Q SYNCHRONIZER CK 1 KBD7 KBIP7 0 IMASKK S KEYBOARD INTERRUPT REQUEST KBIE7 MODEK TO PULLUP/ PULLDOWN ENABLE Figure 9-2. Keyboard Module Block Diagram Addr. Register Name Bit 7 6 5 4 3 2 Keyboard Status and Control Read: $001A Register (INTKBSCR) Write: See page 118. Reset: 0 0 0 0 KEYF 0 $001B $0448 Keyboard Interrupt Enable Read: Register (INTKBIER) Write: See page 119. Reset: Keyboard Interrupt Polarity Read: Register (INTKBIPR) Write: See page 119. Reset: ACKK 1 Bit 0 IMASKK MODEK 0 0 0 0 0 0 0 0 KBIE7 KBIE6 KBIE5 KBIE4 KBIE3 KBIE2 KBIE1 KBIE0 0 0 0 0 0 0 0 0 KBIP7 KBIP6 KBIP5 KBIP4 KBIP3 KBIP2 KBIP1 KBIP0 0 0 0 0 0 0 0 0 = Unimplemented Figure 9-3. I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 115 Keyboard Interrupt Module (KBI) If the MODEK bit is set and depending on the KBIPx bit, the keyboard interrupt pins are both falling (or rising) edge and low (or high) level sensitive, and both of the following actions must occur to clear a keyboard interrupt request: * Vector fetch or software clear -- A vector fetch generates an interrupt acknowledge signal to clear the interrupt request. Software may generate the interrupt acknowledge signal by writing a 1 to the ACKK bit in the keyboard status and control register (INTKBSCR). The ACKK bit is useful in applications that poll the keyboard interrupt pins and require software to clear the keyboard interrupt request. Writing to the ACKK bit prior to leaving an interrupt service routine can also prevent spurious interrupts due to noise. Setting ACKK does not affect subsequent transitions on the keyboard interrupt pins. A falling (or rising) edge that occurs after writing to the ACKK bit latches another interrupt request. If the keyboard interrupt mask bit, IMASKK, is clear, the CPU loads the program counter with the vector address at locations $FFE0 and $FFE1. * Return of all enabled keyboard interrupt pins to 1 (or 0) -- As long as any enabled keyboard interrupt pin is 0 (or 1), the keyboard interrupt remains set. The vector fetch or software clear and the return of all enabled keyboard interrupt pins to 1 (or 0) may occur in any order. If the MODEK bit is clear and depending on the KBIPx bit, the keyboard interrupt pin is falling (or rising) edge sensitive only. With MODEK clear, a vector fetch or software clear immediately clears the keyboard interrupt request. Reset clears the keyboard interrupt request and the MODEK bit, clearing the interrupt request even if a keyboard interrupt pin stays at 0 (or 1). The keyboard flag bit (KEYF) in the keyboard status and control register can be used to see if a pending interrupt exists. The KEYF bit is not affected by the keyboard interrupt mask bit (IMASKK) which makes it useful in applications where polling is preferred. To determine the logic level on a keyboard interrupt pin, use the data direction register to configure the pin as an input and read the data register. NOTE Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding keyboard interrupt pin to be an input, overriding the data direction register. However, the data direction register bit must be a 0 for software to read the pin. 9.4 Keyboard Initialization When a keyboard interrupt pin is enabled, it takes time for the internal pullup/pulldown device to reach a 1 (or 0). Therefore, a false interrupt can occur as soon as the pin is enabled. To prevent a false interrupt on keyboard initialization: 1. Mask keyboard interrupts by setting the IMASKK bit in the keyboard status and control register. 2. Enable the KBI pins and polarity by setting the appropriate KBIEx bits in the keyboard interrupt enable register and the KBIPx bits in the keyboard interrupt polarity register. 3. Write to the ACKK bit in the keyboard status and control register to clear any false interrupts. 4. Clear the IMASKK bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 116 Freescale Semiconductor Low-Power Modes An interrupt signal on an edge-triggered pin can be acknowledged immediately after enabling the pin. An interrupt signal on an edge- and level-triggered interrupt pin must be acknowledged after a delay that depends on the external load. Another way to avoid a false interrupt: 1. Configure the keyboard pins as outputs by setting the appropriate DDRA bits in data direction register A. 2. Write 1s (or 0s) to the appropriate port A data register bits. 3. Enable the KBI pins and polarity by setting the appropriate KBIEx bits in the keyboard interrupt enable register and the KBIPx bits in the keyboard interrupt polarity register. 9.5 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low power-consumption standby modes. 9.5.1 Wait Mode The keyboard module remains active in wait mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of wait mode. 9.5.2 Stop Mode The keyboard module remains active in stop mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of stop mode. 9.6 Keyboard Module During Break Interrupts The system integration module (SIM) controls whether the keyboard interrupt latch can be cleared during the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status bits during the break state. To allow software to clear the keyboard interrupt latch during a break interrupt, write a 1 to the BCFE bit. If a latch is cleared during the break state, it remains cleared when the MCU exits the break state. To protect the latch during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), writing to the keyboard acknowledge bit (ACKK) in the keyboard status and control register during the break state has no effect. See 9.7.1 Keyboard Status and Control Register. 9.7 I/O Registers These registers control and monitor operation of the keyboard module: * Keyboard status and control register (INTKBSCR) * Keyboard interrupt enable register (INTKBIER) * Keyboard interrupt polarity register (INTKBIPR) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 117 Keyboard Interrupt Module (KBI) 9.7.1 Keyboard Status and Control Register The keyboard status and control register: * Flags keyboard interrupt requests * Acknowledges keyboard interrupt requests * Masks keyboard interrupt requests * Controls keyboard interrupt triggering sensitivity Address: $001A Read: Bit 7 6 5 4 3 2 0 0 0 0 KEYF 0 Write: Reset: ACKK 0 0 0 0 0 0 1 Bit 0 IMASKK MODEK 0 0 = Unimplemented Figure 9-4. Keyboard Status and Control Register (INTKBSCR) Bits 7-4 -- Not used These read-only bits always read as 0s. KEYF -- Keyboard Flag Bit This read-only bit is set when a keyboard interrupt is pending. Reset clears the KEYF bit. 1 = Keyboard interrupt pending 0 = No keyboard interrupt pending ACKK -- Keyboard Acknowledge Bit Writing a 1 to this write-only bit clears the keyboard interrupt request. ACKK always reads as 0. Reset clears ACKK. IMASKK -- Keyboard Interrupt Mask Bit Writing a 1 to this read/write bit prevents the output of the keyboard interrupt mask from generating interrupt requests. Reset clears the IMASKK bit. 1 = Keyboard interrupt requests masked 0 = Keyboard interrupt requests not masked MODEK -- Keyboard Triggering Sensitivity Bit This read/write bit controls the triggering sensitivity of the keyboard interrupt pins. Reset clears MODEK. 1 = Keyboard interrupt requests on edge and level detect 0 = Keyboard interrupt requests on edges only MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 118 Freescale Semiconductor I/O Registers 9.7.2 Keyboard Interrupt Enable Register The keyboard interrupt enable register enables or disables each port A pin to operate as a keyboard interrupt pin. Address: $001B Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 KBIE7 KBIE6 KBIE5 KBIE4 KBIE3 KBIE2 KBIE1 KBIE0 0 0 0 0 0 0 0 0 Figure 9-5. Keyboard Interrupt Enable Register (INTKBIER) KBIE7-KBIE0 -- Keyboard Interrupt Enable Bits Each of these read/write bits enables the corresponding keyboard interrupt pin to latch interrupt requests. Reset clears the keyboard interrupt enable register. 1 = PTAx pin enabled as keyboard interrupt pin 0 = PTAx pin not enabled as keyboard interrupt pin 9.7.3 Keyboard Interrupt Polarity Register The KBIP7-KBIP0 bits determine the polarity of the keyboard pin detection. These bits along with the MODEK bit determine whether a logic level (0 or 1) and/or a falling (or rising) edge is being detected. The KBIPx bits also select the pullup resistor (KBIPx = 0) or pulldown resistor (KBIPx = 1) for each enabled keyboard interrupt pin. Address: $0448 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 KBIP7 KBIP6 KBIP5 KBIP4 KBIP3 KBIP2 KBIP1 KBIP0 0 0 0 0 0 0 0 0 Figure 9-6. Keyboard Interrupt Polarity Register (INTKBIPR) KBIP7-KBIP0 -- Keyboard Interrupt Polarity Bits Each of these read/write bits enables the polarity of the keyboard interrupt pin. Reset clears the keyboard interrupt polarity register. 1 = Keyboard polarity is rising edge and/or high level 0 = Keyboard polarity is falling edge and/or low level MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 119 Keyboard Interrupt Module (KBI) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 120 Freescale Semiconductor Chapter 10 Low-Power Modes 10.1 Introduction The microcontroller (MCU) may enter two low-power modes: wait mode and stop mode. They are common to all HC08 MCUs and are entered through instruction execution. This section describes how each module acts in the low-power modes. 10.1.1 Wait Mode The WAIT instruction puts the MCU in a low-power standby mode in which the central processor unit (CPU) clock is disabled but the bus clock continues to run. Power consumption can be further reduced by disabling the low-voltage inhibit (LVI) module through bits in the CONFIG1 register. See Chapter 5 Configuration Register (CONFIG). 10.1.2 Stop Mode Stop mode is entered when a STOP instruction is executed. The CPU clock is disabled and the bus clock is disabled if the OSCENINSTOP bit in the CONFIG2 register is a 0. See Chapter 5 Configuration Register (CONFIG). 10.2 Analog-to-Digital Converter (ADC) 10.2.1 Wait Mode The analog-to-digital converter (ADC) continues normal operation during wait mode. Any enabled CPU interrupt request from the ADC can bring the MCU out of wait mode. If the ADC is not required to bring the MCU out of wait mode, power down the ADC by setting ADCH4-ADCH0 bits in the ADC status and control register before executing the WAIT instruction. 10.2.2 Stop Mode The ADC module is inactive after the execution of a STOP instruction. Any pending conversion is aborted. ADC conversions resume when the MCU exits stop mode after an external interrupt. Allow one conversion cycle to stabilize the analog circuitry. 10.3 Break Module (BRK) 10.3.1 Wait Mode The break (BRK) module is active in wait mode. In the break routine, the user can subtract one from the return address on the stack if the SBSW bit in the break status register is set. 10.3.2 Stop Mode The break module is inactive in stop mode. The STOP instruction does not affect break module register states. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 121 Low-Power Modes 10.4 Central Processor Unit (CPU) 10.4.1 Wait Mode The WAIT instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling interrupts. After exit from wait mode by interrupt, the I bit remains clear. After exit by reset, the I bit is set. * Disables the CPU clock 10.4.2 Stop Mode The STOP instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling external interrupts. After exit from stop mode by external interrupt, the I bit remains clear. After exit by reset, the I bit is set. * Disables the CPU clock After exiting stop mode, the CPU clock begins running after the oscillator stabilization delay. 10.5 Clock Generator Module (CGM) 10.5.1 Wait Mode The clock generator module (CGM) remains active in wait mode. Before entering wait mode, software can disengage and turn off the PLL by clearing the BCS and PLLON bits in the PLL control register (PCTL). Less power-sensitive applications can disengage the PLL without turning it off. Applications that require the PLL to wake the MCU from wait mode also can deselect the PLL output without turning off the PLL. 10.5.2 Stop Mode If the OSCENINSTOP bit in the CONFIG2 register is cleared (default), then the STOP instruction disables the CGM (oscillator and phase-locked loop) and holds low all CGM outputs (CGMXCLK, CGMOUT, and CGMINT). If the OSCENINSTOP bit in the CONFIG2 register is set, then the phase locked loop is shut off, but the oscillator will continue to operate in stop mode. 10.6 Computer Operating Properly Module (COP) 10.6.1 Wait Mode The COP remains active during wait mode. If COP is enabled, a reset will occur at COP timeout. 10.6.2 Stop Mode Stop mode turns off the CGMXCLK input to the COP and clears the SIM counter. Service the COP immediately before entering or after exiting stop mode to ensure a full COP timeout period after entering or exiting stop mode. The STOP bit in the CONFIG1 register enables the STOP instruction. To prevent inadvertently turning off the COP with a STOP instruction, disable the STOP instruction by clearing the STOP bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 122 Freescale Semiconductor External Interrupt Module (IRQ) 10.7 External Interrupt Module (IRQ) 10.7.1 Wait Mode The external interrupt (IRQ) module remains active in wait mode. Clearing the IMASK bit in the IRQ status and control register enables IRQ CPU interrupt requests to bring the MCU out of wait mode. 10.7.2 Stop Mode The IRQ module remains active in stop mode. Clearing the IMASK bit in the IRQ status and control register enables IRQ CPU interrupt requests to bring the MCU out of stop mode. 10.8 Keyboard Interrupt Module (KBI) 10.8.1 Wait Mode The keyboard interrupt (KBI) module remains active in wait mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of wait mode. 10.8.2 Stop Mode The keyboard module remains active in stop mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of stop mode. 10.9 Low-Voltage Inhibit Module (LVI) 10.9.1 Wait Mode If enabled, the low-voltage inhibit (LVI) module remains active in wait mode. If enabled to generate resets, the LVI module can generate a reset and bring the MCU out of wait mode. 10.9.2 Stop Mode If enabled, the LVI module remains active in stop mode. If enabled to generate resets, the LVI module can generate a reset and bring the MCU out of stop mode. 10.10 Enhanced Serial Communications Interface Module (ESCI) 10.10.1 Wait Mode The enhanced serial communications interface (ESCI), or SCI module for short, module remains active in wait mode. Any enabled CPU interrupt request from the SCI module can bring the MCU out of wait mode. If SCI module functions are not required during wait mode, reduce power consumption by disabling the module before executing the WAIT instruction. 10.10.2 Stop Mode The SCI module is inactive in stop mode. The STOP instruction does not affect SCI register states. SCI module operation resumes after the MCU exits stop mode. Because the internal clock is inactive during stop mode, entering stop mode during an SCI transmission or reception results in invalid data. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 123 Low-Power Modes 10.11 Serial Peripheral Interface Module (SPI) 10.11.1 Wait Mode The serial peripheral interface (SPI) module remains active in wait mode. Any enabled CPU interrupt request from the SPI module can bring the MCU out of wait mode. If SPI module functions are not required during wait mode, reduce power consumption by disabling the SPI module before executing the WAIT instruction. 10.11.2 Stop Mode The SPI module is inactive in stop mode. The STOP instruction does not affect SPI register states. SPI operation resumes after an external interrupt. If stop mode is exited by reset, any transfer in progress is aborted, and the SPI is reset. 10.12 Timer Interface Module (TIM1 and TIM2) 10.12.1 Wait Mode The timer interface modules (TIM) remain active in wait mode. Any enabled CPU interrupt request from the TIM can bring the MCU out of wait mode. If TIM functions are not required during wait mode, reduce power consumption by stopping the TIM before executing the WAIT instruction. 10.12.2 Stop Mode The TIM is inactive in stop mode. The STOP instruction does not affect register states or the state of the TIM counter. TIM operation resumes when the MCU exits stop mode after an external interrupt. 10.13 Timebase Module (TBM) 10.13.1 Wait Mode The timebase module (TBM) remains active after execution of the WAIT instruction. In wait mode, the timebase register is not accessible by the CPU. If the timebase functions are not required during wait mode, reduce the power consumption by stopping the timebase before enabling the WAIT instruction. 10.13.2 Stop Mode The timebase module may remain active after execution of the STOP instruction if the oscillator has been enabled to operate during stop mode through the OSCENINSTOP bit in the CONFIG2 register. The timebase module can be used in this mode to generate a periodic wakeup from stop mode. If the oscillator has not been enabled to operate in stop mode, the timebase module will not be active during stop mode. In stop mode, the timebase register is not accessible by the CPU. If the timebase functions are not required during stop mode, reduce the power consumption by stopping the timebase before enabling the STOP instruction. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 124 Freescale Semiconductor Exiting Wait Mode 10.14 Exiting Wait Mode These events restart the CPU clock and load the program counter with the reset vector or with an interrupt vector: * External reset -- A low on the RST pin resets the MCU and loads the program counter with the contents of locations $FFFE and $FFFF. * External interrupt -- A high-to-low transition on an external interrupt pin (IRQ pin) loads the program counter with the contents of locations: $FFFA and $FFFB; IRQ pin. * Break interrupt -- In emulation mode, a break interrupt loads the program counter with the contents of $FFFC and $FFFD. * Computer operating properly (COP) module reset -- A timeout of the COP counter resets the MCU and loads the program counter with the contents of $FFFE and $FFFF. * Low-voltage inhibit (LVI) module reset -- A power supply voltage below the VTRIPF voltage resets the MCU and loads the program counter with the contents of locations $FFFE and $FFFF. * Clock generator module (CGM) interrupt -- A CPU interrupt request from the CGM loads the program counter with the contents of $FFF8 and $FFF9. * Keyboard interrupt (KBI) module -- A CPU interrupt request from the KBI module loads the program counter with the contents of $FFE0 and $FFE1. * Timer 1 interface (TIM1) module interrupt -- A CPU interrupt request from the TIM1 loads the program counter with the contents of: - $FFF2 and $FFF3; TIM1 overflow - $FFF4 and $FFF5; TIM1 channel 1 - $FFF6 and $FFF7; TIM1 channel 0 * Timer 2 interface module (TIM2) interrupt -- A CPU interrupt request from the TIM2 loads the program counter with the contents of: - $FFEC and $FFED; TIM2 overflow - $FFEE and $FFEF; TIM2 channel 1 - $FFF0 and $FFF1; TIM2 channel 0 - $FFCC and $FFCD; TIM2 channel 5 - $FFCE and $FFCF; TIM2 channel 4 - $FFD0 and $FFD1; TIM2 channel 3 - $FFD2 and $FFD3; TIM2 channel 2 * Serial peripheral interface (SPI) module interrupt -- A CPU interrupt request from the SPI loads the program counter with the contents of: - $FFE8 and $FFE9; SPI transmitter - $FFEA and $FFEB; SPI receiver * Serial communications interface (SCI) module interrupt -- A CPU interrupt request from the SCI loads the program counter with the contents of: - $FFE2 and $FFE3; SCI transmitter - $FFE4 and $FFE5; SCI receiver - $FFE6 and $FFE7; SCI receiver error * Analog-to-digital converter (ADC) module interrupt -- A CPU interrupt request from the ADC loads the program counter with the contents of: $FFDE and $FFDF; ADC conversion complete. * Timebase module (TBM) interrupt -- A CPU interrupt request from the TBM loads the program counter with the contents of: $FFDC and $FFDD; TBM interrupt. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 125 Low-Power Modes 10.15 Exiting Stop Mode These events restart the system clocks and load the program counter with the reset vector or with an interrupt vector: * External reset -- A low on the RST pin resets the MCU and loads the program counter with the contents of locations $FFFE and $FFFF. * External interrupt -- A high-to-low transition on an external interrupt pin loads the program counter with the contents of locations: - $FFFA and $FFFB; IRQ pin - $FFE0 and $FFE1; keyboard interrupt pins (low-to-high transition when KBIPx bits are set) * Low-voltage inhibit (LVI) reset -- A power supply voltage below the VTRIPF voltage resets the MCU and loads the program counter with the contents of locations $FFFE and $FFFF. * Break interrupt -- In emulation mode, a break interrupt loads the program counter with the contents of locations $FFFC and $FFFD. * Timebase module (TBM) interrupt -- A TBM interrupt loads the program counter with the contents of locations $FFDC and $FFDD when the timebase counter has rolled over. This allows the TBM to generate a periodic wakeup from stop mode. Upon exit from stop mode, the system clocks begin running after an oscillator stabilization delay. A 12-bit stop recovery counter inhibits the system clocks for 4096 CGMXCLK cycles after the reset or external interrupt. The short stop recovery bit, SSREC, in the CONFIG1 register controls the oscillator stabilization delay during stop recovery. Setting SSREC reduces stop recovery time from 4096 CGMXCLK cycles to 32 CGMXCLK cycles. NOTE Use the full stop recovery time (SSREC = 0) in applications that use an external crystal unless the OSCENINSTOP bit is set. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 126 Freescale Semiconductor Chapter 11 Low-Voltage Inhibit (LVI) 11.1 Introduction This section describes the low-voltage inhibit (LVI) module, which monitors the voltage on the VDD pin and can force a reset when the VDD voltage falls below the LVI trip falling voltage, VTRIPF. 11.2 Features Features of the LVI module include: * Programmable LVI reset * Selectable LVI trip voltage * Programmable stop mode operation 11.3 Functional Description Figure 11-1 shows the structure of the LVI module. The LVI is enabled out of reset. The LVI module contains a bandgap reference circuit and comparator. Clearing the LVI power disable bit, LVIPWRD, enables the LVI to monitor VDD voltage. Clearing the LVI reset disable bit, LVIRSTD, enables the LVI module to generate a reset when VDD falls below a voltage, VTRIPF. Setting the LVI enable in stop mode bit, LVISTOP, enables the LVI to operate in stop mode. Setting the LVI 5-V or 3-V trip point bit, LVI5OR3, enables the trip point voltage, VTRIPF, to be configured for 5-V operation. Clearing the LVI5OR3 bit enables the trip point voltage, VTRIPF, to be configured for 3-V operation. The actual trip points are shown in Chapter 20 Electrical Specifications. NOTE After a power-on reset (POR) the LVI's default mode of operation is 3 V. If a 5-V system is used, the user must set the LVI5OR3 bit to raise the trip point to 5-V operation. Note that this must be done after every power-on reset since the default will revert back to 3-V mode after each power-on reset. If the VDD supply is below the 5-V mode trip voltage but above the 3-V mode trip voltage when POR is released, the part will operate because VTRIPF defaults to 3-V mode after a POR. So, in a 5-V system care must be taken to ensure that VDD is above the 5-V mode trip voltage after POR is released. If the user requires 5-V mode and sets the LVI5OR3 bit after a power-on reset while the VDD supply is not above the VTRIPR for 5-V mode, the microcontroller unit (MCU) will immediately go into reset. The LVI in this case will hold the part in reset until either VDD goes above the rising 5-V trip point, VTRIPR, which will release reset or VDD decreases to approximately 0 V which will re-trigger the power-on reset and reset the trip point to 3-V operation. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 127 Low-Voltage Inhibit (LVI) LVISTOP, LVIPWRD, LVI5OR3, and LVIRSTD are in the configuration register (CONFIG1). See Figure 5-2. Configuration Register 1 (CONFIG1) for details of the LVI's configuration bits. Once an LVI reset occurs, the MCU remains in reset until VDD rises above a voltage, VTRIPR, which causes the MCU to exit reset. See 14.3.2.5 Low-Voltage Inhibit (LVI) Reset for details of the interaction between the SIM and the LVI. The output of the comparator controls the state of the LVIOUT flag in the LVI status register (LVISR). An LVI reset also drives the RST pin low to provide low-voltage protection to external peripheral devices. VDD STOP INSTRUCTION LVISTOP FROM CONFIG1 FROM CONFIG1 LVIRSTD LVIPWRD FROM CONFIG LOW VDD DETECTOR VDD > LVITrip = 0 LVI RESET VDD LVITrip = 1 LVIOUT LVI5OR3 FROM CONFIG1 Figure 11-1. LVI Module Block Diagram Addr. $FE0C Register Name LVI Status Register Read: (LVISR) Write: See page 129. Reset: Bit 7 6 5 4 3 2 1 Bit 0 LVIOUT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 = Unimplemented Figure 11-2. LVI I/O Register Summary 11.3.1 Polled LVI Operation In applications that can operate at VDD levels below the VTRIPF level, software can monitor VDD by polling the LVIOUT bit. In the configuration register, the LVIPWRD bit must be 0 to enable the LVI module, and the LVIRSTD bit must be 1 to disable LVI resets. 11.3.2 Forced Reset Operation In applications that require VDD to remain above the VTRIPF level, enabling LVI resets allows the LVI module to reset the MCU when VDD falls below the VTRIPF level. In the configuration register, the LVIPWRD and LVIRSTD bits must be cleared to enable the LVI module and to enable LVI resets. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 128 Freescale Semiconductor LVI Status Register 11.3.3 Voltage Hysteresis Protection Once the LVI has triggered (by having VDD fall below VTRIPF), the LVI will maintain a reset condition until VDD rises above the rising trip point voltage, VTRIPR. This prevents a condition in which the MCU is continually entering and exiting reset if VDD is approximately equal to VTRIPF. VTRIPR is greater than VTRIPF by the hysteresis voltage, VHYS. 11.3.4 LVI Trip Selection The LVI5OR3 bit in the configuration register selects whether the LVI is configured for 5-V or 3-V protection. NOTE The microcontroller is guaranteed to operate at a minimum supply voltage. The trip point (VTRIPF [5 V] or VTRIPF [3 V]) may be lower than this. See Chapter 20 Electrical Specifications for the actual trip point voltages. 11.4 LVI Status Register The LVI status register (LVISR) indicates if the VDD voltage was detected below the VTRIPF level. Address: Read: $FE0C Bit 7 6 5 4 3 2 1 Bit 0 LVIOUT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 11-3. LVI Status Register (LVISR) LVIOUT -- LVI Output Bit This read-only flag becomes set when the VDD voltage falls below the VTRIPF trip voltage (see Table 11-1). Reset clears the LVIOUT bit. Table 11-1. LVIOUT Bit Indication VDD LVIOUT VDD > VTRIPR 0 VDD < VTRIPF 1 VTRIPF < VDD < VTRIPR Previous value 11.5 LVI Interrupts The LVI module does not generate interrupt requests. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 129 Low-Voltage Inhibit (LVI) 11.6 Low-Power Modes The STOP and WAIT instructions put the MCU in low power-consumption standby modes. 11.6.1 Wait Mode If enabled, the LVI module remains active in wait mode. If enabled to generate resets, the LVI module can generate a reset and bring the MCU out of wait mode. 11.6.2 Stop Mode If enabled in stop mode (LVISTOP bit in the configuration register is set), the LVI module remains active in stop mode. If enabled to generate resets, the LVI module can generate a reset and bring the MCU out of stop mode. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 130 Freescale Semiconductor Chapter 12 Input/Output (I/O) Ports 12.1 Introduction Bidirectional input-output (I/O) pins form seven parallel ports. All I/O pins are programmable as inputs or outputs. All individual bits within port A, port C, port D and port F are software configurable with pullup devices if configured as input port bits. The pullup devices are automatically and dynamically disabled when a port bit is switched to output mode. 12.2 Unused Pin Termination Input pins and I/O port pins that are not used in the application must be terminated. This prevents excess current caused by floating inputs, and enhances immunity during noise or transient events. Termination methods include: 1. Configuring unused pins as outputs and driving high or low; 2. Configuring unused pins as inputs and enabling internal pull-ups; 3. Configuring unused pins as inputs and using external pull-up or pull-down resistors. Never connect unused pins directly to VDD or VSS. Since some general-purpose I/O pins are not available on all packages, these pins must be terminated as well. Either method 1 or 2 above are appropriate. Addr. $0000 $0001 $0002 Register Name Read: Port A Data Register (PTA) Write: See page 135. Reset: Read: Port B Data Register (PTB) Write: See page 138. Reset: Read: Port C Data Register (PTC) Write: See page 140. Reset: Bit 7 6 5 4 3 2 1 Bit 0 PTA7 PTA6 PTA5 PTA4 PTA3 PTA2 PTA1 PTA0 PTB2 PTB1 PTB0 PTC2 PTC1 PTC0 Unaffected by reset PTB7 PTB6 PTB5 PTB4 PTB3 Unaffected by reset 1 PTC6 PTC5 PTC4 PTC3 Unaffected by reset = Unimplemented Figure 12-1. I/O Port Register Summary (Sheet 1 of 3) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 131 Input/Output (I/O) Ports Addr. $0003 $0004 $0005 $0006 $0007 $0008 $000C $000D $000E $000F Register Name Read: Port D Data Register (PTD) Write: See page 142. Reset: Read: Data Direction Register A (DDRA) Write: See page 136. Reset: Bit 7 6 5 4 3 2 1 Bit 0 PTD7 PTD6 PTD5 PTD4 PTD3 PTD2 PTD1 PTD0 Unaffected by reset DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 Read: Port E Data Register (PTE) Write: See page 145. Reset: 0 0 PTE5 PTE4 PTE3 PTE2 PTE1 PTE0 Read: Data Direction Register E (DDRE) Write: See page 146. Reset: 0 0 0 Read: Data Direction Register B (DDRB) Write: See page 138. Reset: Read: Data Direction Register C (DDRC) Write: See page 140. Reset: Read: Data Direction Register D (DDRD) Write: See page 143. Reset: 0 Unaffected by reset Read: Port A Input Pullup Enable PTAPUE7 Register (PTAPUE) Write: See page 137. Reset: 0 Read: Port C Input Pullup Enable Register (PTCPUE) Write: See page 142. Reset: 0 0 Read: Port D Input Pullup Enable PTDPUE7 Register (PTDPUE) Write: See page 145. Reset: 0 DDRE5 DDRE4 DDRE3 DDRE2 DDRE1 DDRE0 0 0 0 0 0 0 0 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0 0 0 0 0 0 0 0 PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0 0 0 0 0 0 0 0 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0 0 0 0 0 0 0 0 = Unimplemented Figure 12-1. I/O Port Register Summary (Sheet 2 of 3) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 132 Freescale Semiconductor Unused Pin Termination Addr. Register Name Port F Data Register Read: (PTF) Write: See page 147. Reset: $0440 Port G Data Register Read: (PTG) Write: See page 149. Reset: $0441 Data Direction Register F Read: (DDRF) Write: See page 148. Reset: $0444 Data Direction Register G Read: (DDRG) Write: See page 150. Reset: $0445 Bit 7 6 5 4 3 2 1 Bit 0 PTF7 PTF6 PTF5 PTF4 PTAF3 PTF2 PTF1 PTF0 PTG2 PTG1 PTG0 Unaffected by reset PTG7 PTG6 PTG5 PTG4 PTG3 Unaffected by reset DDRF7 DDRF6 DDRF5 DDRF4 DDRF3 DDRF2 DDRF1 DDRF0 0 0 0 0 0 0 0 0 DDRG7 DDRG6 DDRG5 DDRG4 DDRG3 DDRG2 DDRG1 DDRG0 0 0 0 0 0 0 0 0 = Unimplemented Figure 12-1. I/O Port Register Summary (Sheet 3 of 3) Table 12-1. Port Control Register Bits Summary Port A B Bit DDR Module Control 0 DDRA0 KBIE0 PTA0/KBD0/AD8 1 DDRA1 KBIE1 PTA1/KBD1/AD9 2 DDRA2 KBIE2 PTA2/KBD2/AD10 3 DDRA3 4 DDRA4 5 DDRA5 KBIE5 PTA5/KBD5/AD13 6 DDRA6 KBIE6 PTA6/KBD6/AD14 7 DDRA7 KBIE7 PTA7/KBD7/AD15 0 DDRB0 PTB0/AD0 1 DDRB1 PTB1/AD1 2 DDRB2 PTB2/AD2 3 DDRB3 4 DDRB4 5 DDRB5 PTB5/AD5 6 DDRB6 PTB6/AD6 7 DDRB7 PTB7/AD7 KBD ADC KBIE3 KBIE4 ADCH4-ADCH0 Module Control ADC[15:8] -- ADCH4-ADCH0 Pin PTA3/KBD3/AD11 PTA4/KBD4/AD12 PTB3/AD3 -- PTB4/AD4 Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 133 Input/Output (I/O) Ports Table 12-1. Port Control Register Bits Summary (Continued) Port C D E F G Bit DDR Module Control Module Control 0 DDRC0 PTC0 1 DDRC1 PTC1 2 DDRC2 PTC2 3 DDRC3 4 DDRC4 PTC4 5 DDRC5 PTC5 6 DDRC6 PTC6 0 DDRD0 PTD0/SS/MCLK 1 DDRD1 2 DDRD2 3 DDRD3 4 DDRD4 5 DDRD5 6 DDRD6 7 DDRD7 0 DDRE0 1 DDRE1 2 DDRE2 3 DDRE3 4 DDRE4 PTE4 5 DDRE5 PTE5 0 DDRF0 PTF0 1 DDRF1 PTF1 2 DDRF2 PTF2 3 DDRF3 4 DDRF4 5 DDRF5 6 DDRF6 7 DDRF7 0 DDRG0 PTG0/AD16 1 DDRG1 PTG1/AD17 2 DDRG2 PTG2/AD18 3 DDRG3 4 DDRG4 5 DDRG5 PTG5/AD21 6 DDRG6 PTG6/AD22 7 DDRG7 PTG7/AD23 -- SPI TIM1 TIM2 SCI ELS0B:ELS0A PTC3 PTD1/MISO PTD2/MOSI -- -- PTD3/SPSCK PTD4/T1CH0 ELS1B:ELS1A PTD5/T1CH1 ELS0B:ELS0A PTD6/T2CH0 ELS1B:ELS1A PTD7/T2CH1 PTE0/TxD ENSCI ELS2B:ELS2A ADC -- SPE PTE1/RxD -- TIM2 Pin -- PTE2 -- -- PTE3 PTF3 PTF4/T2CH2 ELS3B:ELS3A PTF5/T2CH3 ELS4B:ELS4A PTF6/T2CH4 ELS5B:ELS5A PTF7/T2CH5 ADCH[23:16] -- PTG3/AD19 -- PTG4/AD20 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 134 Freescale Semiconductor Port A 12.3 Port A Port A is an 8-bit special-function port that shares all eight of its pins with the keyboard interrupt (KBI) module and the ADC module. Port A also has software configurable pullup devices if configured as an input port. 12.3.1 Port A Data Register The port A data register (PTA) contains a data latch for each of the eight port A pins. Address: $0000 Bit 7 6 5 4 3 2 1 Bit 0 PTA7 PTA6 PTA5 PTA4 PTA3 PTA2 PTA1 PTA0 Alternate Function: KBD7 KBD6 KBD5 KBD4 KBD3 KBD2 KBD1 KBD0 Alternate Function: AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 Read: Write: Reset: Unaffected by reset Figure 12-2. Port A Data Register (PTA) PTA7-PTA0 -- Port A Data Bits These read/write bits are software programmable. Data direction of each port A pin is under the control of the corresponding bit in data direction register A. Reset has no effect on port A data. KBD7-KBD0 -- Keyboard Inputs The keyboard interrupt enable bits, KBIE7-KBIE0, in the keyboard interrupt control register (KBICR) enable the port A pins as external interrupt pins. See Chapter 9 Keyboard Interrupt Module (KBI) AD15-AD8 -- Analog-to-Digital Input Bits AD15-AD8 are pins used for the input channels to the analog-to-digital converter module. The channel select bits in the ADC status and control register define which port A pin will be used as an ADC input and overrides any control from the port I/O logic by forcing that pin as the input to the analog circuitry. NOTE Care must be taken when reading port A while applying analog voltages to AD15-AD8 pins. If the appropriate ADC channel is not enabled, excessive current drain may occur if analog voltages are applied to the PTAx/KBDx/ADx pin, while PTA is read as a digital input during the CPU read cycle. Those ports not selected as analog input channels are considered digital I/O ports. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 135 Input/Output (I/O) Ports 12.3.2 Data Direction Register A Data direction register A (DDRA) determines whether each port A pin is an input or an output. Writing a 1 to a DDRA bit enables the output buffer for the corresponding port A pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0004 Bit 7 6 5 4 3 2 1 Bit 0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 Figure 12-3. Data Direction Register A (DDRA) DDRA7-DDRA0 -- Data Direction Register A Bits These read/write bits control port A data direction. Reset clears DDRA7-DDRA0, configuring all port A pins as inputs. 1 = Corresponding port A pin configured as output 0 = Corresponding port A pin configured as input NOTE Avoid glitches on port A pins by writing to the port A data register before changing data direction register A bits from 0 to 1. Figure 12-4 shows the port A I/O logic. When bit DDRAx is a 1, reading address $0000 reads the PTAx data latch. When bit DDRAx is a 0, reading address $0000 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-2 summarizes the operation of the port A pins. VDD PTAPUEx READ DDRA ($0004) INTERNAL DATA BUS WRITE DDRA ($0004) RESET WRITE PTA ($0000) DDRAx PTAx INTERNAL PULLUP DEVICE PTAx READ PTA ($0000) Figure 12-4. Port A I/O Circuit MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 136 Freescale Semiconductor Port A Table 12-2. Port A Pin Functions PTAPUE Bit DDRA Bit PTA Bit I/O Pin Mode Accesses to DDRA Accesses to PTA Read/Write Read Write 1 0 X(1) Input, VDD(2) DDRA7-DDRA0 Pin PTA7-PTA0(3) 0 0 X Input, Hi-Z(4) DDRA7-DDRA0 Pin PTA7-PTA0(3) X 1 X Output DDRA7-DDRA0 PTA7-PTA0 PTA7-PTA0 1. X = Don't care 2. I/O pin pulled up to VDD by internal pullup device 3. Writing affects data register, but does not affect input. 4. Hi-Z = High impedance 12.3.3 Port A Input Pullup Enable Register The port A input pullup enable register (PTAPUE) contains a software configurable pullup device for each of the eight port A pins. Each bit is individually configurable and requires that the data direction register, DDRA, bit be configured as an input. Each pullup is automatically and dynamically disabled when a port bit's DDRA is configured for output mode. NOTE Pullup or pulldown resistors are automatically selected for keyboard interrupt pins depending on the bit settings in the keyboard interrupt polarity register (INTKBIPR) see 9.7.3 Keyboard Interrupt Polarity Register. Address: $000D Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 PTAPUE7 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0 0 0 0 0 0 0 0 0 Figure 12-5. Port A Input Pullup Enable Register (PTAPUE) PTAPUE7-PTAPUE0 -- Port A Input Pullup Enable Bits These writable bits are software programmable to enable pullup devices on an input port bit. 1 = Corresponding port A pin configured to have internal pullup 0 = Corresponding port A pin has internal pullup disconnected MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 137 Input/Output (I/O) Ports 12.4 Port B Port B is an 8-bit special-function port that shares all eight of its pins with the analog-to-digital converter (ADC) module. 12.4.1 Port B Data Register The port B data register (PTB) contains a data latch for each of the eight port pins. Address: $0001 Read: Write: Bit 7 6 5 4 3 2 1 Bit 0 PTB7 PTB6 PTB5 PTB4 PTB3 PTB2 PTB1 PTB0 AD7 AD6 AD5 AD2 AD1 AD0 Reset: Unaffected by reset Alternate Function: AD4 AD3 Figure 12-6. Port B Data Register (PTB) PTB7-PTB0 -- Port B Data Bits These read/write bits are software-programmable. Data direction of each port B pin is under the control of the corresponding bit in data direction register B. Reset has no effect on port B data. AD7-AD0 -- Analog-to-Digital Input Bits AD7-AD0 are pins used for the input channels to the analog-to-digital converter module. The channel select bits in the ADC status and control register define which port B pin will be used as an ADC input and overrides any control from the port I/O logic by forcing that pin as the input to the analog circuitry. NOTE Care must be taken when reading port B while applying analog voltages to AD7-AD0 pins. If the appropriate ADC channel is not enabled, excessive current drain may occur if analog voltages are applied to the PTBx/ADx pin, while PTB is read as a digital input during the CPU read cycle. Those ports not selected as analog input channels are considered digital I/O ports. 12.4.2 Data Direction Register B Data direction register B (DDRB) determines whether each port B pin is an input or an output. Writing a 1 to a DDRB bit enables the output buffer for the corresponding port B pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0005 Bit 7 6 5 4 3 2 1 Bit 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 Figure 12-7. Data Direction Register B (DDRB) DDRB7-DDRB0 -- Data Direction Register B Bits These read/write bits control port B data direction. Reset clears DDRB7-DDRB0, configuring all port B pins as inputs. 1 = Corresponding port B pin configured as output 0 = Corresponding port B pin configured as input MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 138 Freescale Semiconductor Port B NOTE Avoid glitches on port B pins by writing to the port B data register before changing data direction register B bits from 0 to 1. Figure 12-8 shows the port B I/O logic. When bit DDRBx is a 1, reading address $0001 reads the PTBx data latch. When bit DDRBx is a 0, reading address $0001 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-3 summarizes the operation of the port B pins. READ DDRB ($0005) INTERNAL DATA BUS WRITE DDRB ($0005) DDRBx RESET WRITE PTB ($0001) PTBx PTBx READ PTB ($0001) Figure 12-8. Port B I/O Circuit Table 12-3. Port B Pin Functions DDRB Bit PTB Bit I/O Pin Mode Accesses to DDRB Read/Write Read Accesses to PTB Write 0 X(1) Input, Hi-Z(2) DDRB7-DDRB0 Pin PTB7-PTB0(3) 1 X Output DDRB7-DDRB0 PTB7-PTB0 PTB7-PTB0 1. X = Don't care 2. Hi-Z = High impedance 3. Writing affects data register, but does not affect input. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 139 Input/Output (I/O) Ports 12.5 Port C Port C is a 7-bit, general-purpose bidirectional I/O port. Port C also has software configurable pullup devices if configured as an input port. 12.5.1 Port C Data Register The port C data register (PTC) contains a data latch for each of the seven port C pins. NOTE Bit 6 through bit 2 of PTC are not available in the 32-pin LQFP package. Address: $0002 Bit 7 Read: 1 Write: 6 5 4 3 2 1 Bit 0 PTC6 PTC5 PTC4 PTC3 PTC2 PTC1 PTC0 Reset: Unaffected by reset = Unimplemented Figure 12-9. Port C Data Register (PTC) PTC6-PTC0 -- Port C Data Bits These read/write bits are software-programmable. Data direction of each port C pin is under the control of the corresponding bit in data direction register C. Reset has no effect on port C data. 12.5.2 Data Direction Register C Data direction register C (DDRC) determines whether each port C pin is an input or an output. Writing a 1 to a DDRC bit enables the output buffer for the corresponding port C pin; a 0 disables the output buffer. Address: $0006 Bit 7 Read: 0 Write: Reset: 0 6 5 4 3 2 1 Bit 0 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 = Unimplemented Figure 12-10. Data Direction Register C (DDRC) DDRC6-DDRC0 -- Data Direction Register C Bits These read/write bits control port C data direction. Reset clears DDRC6-DDRC0, configuring all port C pins as inputs. 1 = Corresponding port C pin configured as output 0 = Corresponding port C pin configured as input NOTE Avoid glitches on port C pins by writing to the port C data register before changing data direction register C bits from 0 to 1. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 140 Freescale Semiconductor Port C Figure 12-11 shows the port C I/O logic. When bit DDRCx is a 1, reading address $0002 reads the PTCx data latch. When bit DDRCx is a 0, reading address $0002 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-4 summarizes the operation of the port C pins. VDD PTCPUEx READ DDRC ($0006) INTERNAL PULLUP DEVICE INTERNAL DATA BUS WRITE DDRC ($0006) RESET WRITE PTC ($0002) DDRCx PTCx PTCx READ PTC ($0002) Figure 12-11. Port C I/O Circuit Table 12-4. Port C Pin Functions PTCPUE Bit DDRC Bit PTC Bit I/O Pin Mode Accesses to DDRC Read/Write Read Accesses to PTC Write 1 0 X(1) Input, VDD(2) DDRC6-DDRC0 Pin PTC6-PTC0(3) 0 0 X Input, Hi-Z(4) DDRC6-DDRC0 Pin PTC6-PTC0(3) X 1 X Output DDRC6-DDRC0 PTC6-PTC0 PTC6-PTC0 1. X = Don't care 2. I/O pin pulled up to VDD by internal pullup device. 3. Writing affects data register, but does not affect input. 4. Hi-Z = High impedance MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 141 Input/Output (I/O) Ports 12.5.3 Port C Input Pullup Enable Register The port C input pullup enable register (PTCPUE) contains a software configurable pullup device for each of the seven port C pins. Each bit is individually configurable and requires that the data direction register, DDRC, bit be configured as an input. Each pullup is automatically and dynamically disabled when a port bit's DDRC is configured for output mode. Address: $000E Bit 7 Read: 0 Write: Reset: 6 5 4 3 2 1 Bit 0 PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0 0 0 0 0 0 0 0 0 = Unimplemented Figure 12-12. Port C Input Pullup Enable Register (PTCPUE) PTCPUE6-PTCPUE0 -- Port C Input Pullup Enable Bits These writable bits are software programmable to enable pullup devices on an input port bit. 1 = Corresponding port C pin configured to have internal pullup 0 = Corresponding port C pin internal pullup disconnected 12.6 Port D Port D is an 8-bit special-function port that shares four of its pins with the serial peripheral interface (SPI) module and four of its pins with two timer interface (TIM1 and TIM2) modules. Port D also has software configurable pullup devices if configured as an input port. PTD0 is shared with the MCLK output. 12.6.1 Port D Data Register The port D data register (PTD) contains a data latch for each of the eight port D pins. Address: Read: Write: $0003 Bit 7 6 5 4 3 2 1 Bit 0 PTD7 PTD6 PTD5 PTD4 PTD3 PTD2 PTD1 PTD0 T2CH1 T2CH0 T1CH1 T1CH0 MOSI MISO SS Reset: Alternate Function: Unaffected by reset SPSCK MCLK Figure 12-13. Port D Data Register (PTD) PTD7-PTD0 -- Port D Data Bits These read/write bits are software-programmable. Data direction of each port D pin is under the control of the corresponding bit in data direction register D. Reset has no effect on port D data. T2CH1 and T2CH0 -- Timer 2 Channel I/O Bits The PTD5/T2CH1-PTD4/T2CH0 pins are the TIM2 input capture/output compare pins. The edge/level select bits, ELSxB:ELSxA, determine whether the PTD7/T2CH1-PTD6/T2CH0 pins are timer channel I/O pins or general-purpose I/O pins. See Chapter 17 Timer Interface Module (TIM1) and Chapter 18 Timer Interface Module (TIM2). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 142 Freescale Semiconductor Port D T1CH1 and T1CH0 -- Timer 1 Channel I/O Bits The PTD7/T1CH1-PTD6/T1CH0 pins are the TIM1 input capture/output compare pins. The edge/level select bits, ELSxB and ELSxA, determine whether the PTD7/T1CH1-PTD6/T1CH0 pins are timer channel I/O pins or general-purpose I/O pins. See Chapter 17 Timer Interface Module (TIM1) and Chapter 18 Timer Interface Module (TIM2). SPSCK -- SPI Serial Clock The PTD3/SPSCK pin is the serial clock input of the SPI module. When the SPE bit is clear, the PTD3/SPSCK pin is available for general-purpose I/O. MOSI -- Master Out/Slave In The PTD2/MOSI pin is the master out/slave in terminal of the SPI module. When the SPE bit is clear, the PTD2/MOSI pin is available for general-purpose I/O. MISO -- Master In/Slave Out The PTD1/MISO pin is the master in/slave out terminal of the SPI module. When the SPI enable bit, SPE, is clear, the SPI module is disabled, and the PTD1/MISO pin is available for general-purpose I/O. SS -- Slave Select The PTD0/SS pin is the slave select input of the SPI module. When the SPE bit is clear, or when the SPI master bit, SPMSTR, is set, the PTD0/SS pin is available for general-purpose I/O. When the SPI is enabled, the DDRD0 bit in data direction register D (DDRD) has no effect on the PTD0/SS pin. Data direction register D (DDRD) does not affect the data direction of port D pins that are being used by the SPI module. However, the DDRD bits always determine whether reading port D returns the states of the latches or the states of the pins. See Table 12-5. 12.6.2 Data Direction Register D Data direction register D (DDRD) determines whether each port D pin is an input or an output. Writing a 1 to a DDRD bit enables the output buffer for the corresponding port D pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0007 Bit 7 6 5 4 3 2 1 Bit 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 Figure 12-14. Data Direction Register D (DDRD) DDRD7-DDRD0 -- Data Direction Register D Bits These read/write bits control port D data direction. Reset clears DDRD7-DDRD0, configuring all port D pins as inputs. 1 = Corresponding port D pin configured as output 0 = Corresponding port D pin configured as input NOTE Avoid glitches on port D pins by writing to the port D data register before changing data direction register D bits from 0 to 1. Figure 12-15 shows the port D I/O logic. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 143 Input/Output (I/O) Ports When bit DDRDx is a 1, reading address $0003 reads the PTDx data latch. When bit DDRDx is a 0, reading address $0003 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-5 summarizes the operation of the port D pins. VDD PTDPUEx READ DDRD ($0007) INTERNAL PULLUP DEVICE WRITE DDRD ($0007) DDRDx INTERNAL DATA BUS RESET WRITE PTD ($0003) PTDx PTDx READ PTD ($0003) Figure 12-15. Port D I/O Circuit Table 12-5. Port D Pin Functions PTDPUE Bit DDRD Bit PTD Bit Accesses to DDRD I/O Pin Mode Accesses to PTD Read/Write Read Write (2) DDRD7-DDRD0 Pin PTD7-PTD0(3) 1 0 X(1) 0 0 X Input, Hi-Z(4) DDRD7-DDRD0 Pin PTD7-PTD0(3) X 1 X Output DDRD7-DDRD0 PTD7-PTD0 PTD7-PTD0 Input, VDD 1. X = Don't care 2. I/O pin pulled up to VDD by internal pullup device. 3. Writing affects data register, but does not affect input. 4. Hi-Z = High imp[edance MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 144 Freescale Semiconductor Port E 12.6.3 Port D Input Pullup Enable Register The port D input pullup enable register (PTDPUE) contains a software configurable pullup device for each of the eight port D pins. Each bit is individually configurable and requires that the data direction register, DDRD, bit be configured as an input. Each pullup is automatically and dynamically disabled when a port bit's DDRD is configured for output mode. Address: $000F Read: Write: Bit 7 6 5 4 3 2 1 Bit 0 PTDPUE7 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0 0 0 0 0 0 0 0 0 Reset: Figure 12-16. Port D Input Pullup Enable Register (PTDPUE) PTDPUE7-PTDPUE0 -- Port D Input Pullup Enable Bits These writable bits are software programmable to enable pullup devices on an input port bit. 1 = Corresponding port D pin configured to have internal pullup 0 = Corresponding port D pin has internal pullup disconnected 12.7 Port E Port E is a 6-bit special-function port that shares two of its pins with the enhanced serial communications interface (ESCI) module. 12.7.1 Port E Data Register The port E data register contains a data latch for each of the six port E pins. Address: Read: Write: $0008 Bit 7 6 0 0 5 4 3 2 1 Bit 0 PTE5 PTE4 PTE3 PTE2 PTE1 PTE0 RxD TxD Reset: Unaffected by reset Alternate Function: = Unimplemented Figure 12-17. Port E Data Register (PTE) PTE5-PTE0 -- Port E Data Bits These read/write bits are software-programmable. Data direction of each port E pin is under the control of the corresponding bit in data direction register E. Reset has no effect on port E data. NOTE Data direction register E (DDRE) does not affect the data direction of port E pins that are being used by the ESCI module. However, the DDRE bits always determine whether reading port E returns the states of the latches or the states of the pins. See Table 12-6. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 145 Input/Output (I/O) Ports RxD -- SCI Receive Data Input The PTE1/RxD pin is the receive data input for the ESCI module. When the enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the PTE1/RxD pin is available for general-purpose I/O. See Chapter 13 Enhanced Serial Communications Interface (ESCI) Module. TxD -- SCI Transmit Data Output The PTE0/TxD pin is the transmit data output for the ESCI module. When the enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the PTE0/TxD pin is available for general-purpose I/O. See Chapter 13 Enhanced Serial Communications Interface (ESCI) Module. 12.7.2 Data Direction Register E Data direction register E (DDRE) determines whether each port E pin is an input or an output. Writing a 1 to a DDRE bit enables the output buffer for the corresponding port E pin; a 0 disables the output buffer. Address: Read: $000C Bit 7 6 0 0 0 0 Write: Reset: 5 4 3 2 1 Bit 0 DDRE5 DDRE4 DDRE3 DDRE2 DDRE1 DDRE0 0 0 0 0 0 0 = Unimplemented Figure 12-18. Data Direction Register E (DDRE) DDRE5-DDRE0 -- Data Direction Register E Bits These read/write bits control port E data direction. Reset clears DDRE5-DDRE0, configuring all port E pins as inputs. 1 = Corresponding port E pin configured as output 0 = Corresponding port E pin configured as input NOTE Avoid glitches on port E pins by writing to the port E data register before changing data direction register E bits from 0 to 1. Figure 12-19 shows the port E I/O logic. When bit DDREx is a 1, reading address $0008 reads the PTEx data latch. When bit DDREx is a 0, reading address $0008 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-6 summarizes the operation of the port E pins. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 146 Freescale Semiconductor Port F READ DDRE ($000C) INTERNAL DATA BUS WRITE DDRE ($000C) DDREx RESET WRITE PTE ($0008) PTEx PTEx READ PTE ($0008) Figure 12-19. Port E I/O Circuit Table 12-6. Port E Pin Functions DDRE Bit PTE Bit I/O Pin Mode Accesses to DDRE Read/Write Read Accesses to PTE Write 0 X(1) Input, Hi-Z(2) DDRE5-DDRE0 Pin PTE5-PTE0(3) 1 X Output DDRE5-DDRE0 PTE5-PTE0 PTE5-PTE0 1. X = Don't care 2. Hi-Z = High impedance 3. Writing affects data register, but does not affect input. 12.8 Port F Port F is an 8-bit special-function port that shares four of its pins with the timer interface (TIM2) module. 12.8.1 Port F Data Register The port F data register (PTF) contains a data latch for each of the eight port F pins. Address: Read: Write: $0440 Bit 7 6 5 4 3 2 1 Bit 0 PTF7 PTF6 PTF5 PTF4 PTF3 PTF2 PTF1 PTF0 T2CH5 T2CH4 T2CH3 T2CH2 Reset: Alternate Function: Unaffected by reset = Unimplemented Figure 12-20. Port F Data Register (PTF) PTF7-PTF0 -- Port F Data Bits These read/write bits are software-programmable. Data direction of each port F pin is under the control of the corresponding bit in data direction register F. Reset has no effect on port F data. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 147 Input/Output (I/O) Ports T2CH5-T2CH2 -- Timer 2 Channel I/O Bits The PTF7/T2CH5-PTF4/T2CH2 pins are the TIM2 input capture/output compare pins. The edge/level select bits, ELSxB:ELSxA, determine whether the PTF7/T2CH5-PTF4/T2CH2 pins are timer channel I/O pins or general-purpose I/O pins. See Chapter 17 Timer Interface Module (TIM1) and Chapter 18 Timer Interface Module (TIM2). 12.8.2 Data Direction Register F Data direction register F (DDRF) determines whether each port F pin is an input or an output. Writing a 1 to a DDRF bit enables the output buffer for the corresponding port F pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0444 Bit 7 6 5 4 3 2 1 Bit 0 DDRF7 DDRF6 DDRF5 DDRF4 DDRF3 DDRF2 DDRF1 DDRF0 0 0 0 0 0 0 0 0 Figure 12-21. Data Direction Register F (DDRF) DDRF7-DDRF0 -- Data Direction Register F Bits These read/write bits control port F data direction. Reset clears DDRF7-DDRF0, configuring all port F pins as inputs. 1 = Corresponding port F pin configured as output 0 = Corresponding port F pin configured as input NOTE Avoid glitches on port F pins by writing to the port F data register before changing data direction register F bits from 0 to 1. Figure 12-22 shows the port F I/O logic. READ DDRF ($0444) WRITE DDRF ($0444) INTERNAL DATA BUS RESET WRITE PTF ($0440) DDRFx PTFx PTFx READ PTD ($0440) Figure 12-22. Port F I/O Circuit When bit DDRFx is a 1, reading address $0440 reads the PTFx data latch. When bit DDRFx is a 0, reading address $0440 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-7 summarizes the operation of the port F pins. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 148 Freescale Semiconductor Port G Table 12-7. Port F Pin Functions DDRF Bit PTF Bit I/O Pin Mode Accesses to DDRF Accesses to PTF Read/Write Read WritE 0 X(1) Input, Hi-Z(2) DDRF7-DDRF0 Pin PTF7-PTF0(3) 1 X Output DDRF7-DDRF0 PTF7-PTF0 PTF7-PTF0 1. X = Don't care 2. Hi-Z = High impedance 3. Writing affects data register, but does not affect input. 12.9 Port G Port G is an 8-bit special-function port that shares all eight of its pins with the analog-to-digital converter (ADC) module. 12.9.1 Port G Data Register The port G data register (PTG) contains a data latch for each of the eight port pins. Address: Read: Write: $0441 Bit 7 6 5 4 3 2 1 Bit 0 PTG7 PTG6 PTG5 PTG4 PTG3 PTG2 PTG1 PTG0 AD18 AD17 AD16 Reset: Alternate Function: Unaffected by reset AD23 AD22 AD21 AD20 AD19 Figure 12-23. Port G Data Register (PTG) PTG7-PTG0 -- Port G Data Bits These read/write bits are software-programmable. Data direction of each port G pin is under the control of the corresponding bit in data direction register G. Reset has no effect on port G data. AD23-AD16 -- Analog-to-Digital Input Bits AD23-AD16 are pins used for the input channels to the analog-to-digital converter module. The channel select bits in the ADC status and control register define which port G pin will be used as an ADC input and overrides any control from the port I/O logic by forcing that pin as the input to the analog circuitry. NOTE Care must be taken when reading port G while applying analog voltages to AD23-AD16 pins. If the appropriate ADC channel is not enabled, excessive current drain may occur if analog voltages are applied to the PTGx/ADx pin, while PTG is read as a digital input during the CPU read cycle. Those ports not selected as analog input channels are considered digital I/O ports. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 149 Input/Output (I/O) Ports 12.9.2 Data Direction Register G Data direction register G (DDRG) determines whether each port G pin is an input or an output. Writing a 1 to a DDRG bit enables the output buffer for the corresponding port G pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0445 Bit 7 6 5 4 3 2 1 Bit 0 DDRG7 DDRG6 DDRG5 DDRG4 DDRG3 DDRG2 DDRG1 DDRG0 0 0 0 0 0 0 0 0 Figure 12-24. Data Direction Register G (DDRG) DDRG7-DDRG0 -- Data Direction Register G Bits These read/write bits control port G data direction. Reset clears DDRG7-DDRG0], configuring all port G pins as inputs. 1 = Corresponding port G pin configured as output 0 = Corresponding port G pin configured as input NOTE Avoid glitches on port G pins by writing to the port G data register before changing data direction register G bits from 0 to 1. Figure 12-25 shows the port G I/O logic. READ DDRG ($0445) INTERNAL DATA BUS WRITE DDRG ($0445) DDRGx RESET WRITE PTG ($0441) PTGx PTGx READ PTG ($0441) Figure 12-25. Port G I/O Circuit When bit DDRGx is a 1, reading address $0441 reads the PTGx data latch. When bit DDRGx is a 0, reading address $0441 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-8 summarizes the operation of the port G pins. Table 12-8. Port G Pin Functions DDRG Bit 0 1 PTG Bit (1) X X I/O Pin Mode Input, Hi-Z(2) Output Accesses to DDRG Accesses to PTG Read/Write Read Write DDRG7-DDRG0 Pin PTG7-PTG0(3) DDRG7-DDRG0 PTG7-PTG0 PTG7-PTG0 1. X = Don't care 2. Hi-Z = High impedance 3. Writing affects data register, but does not affect input. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 150 Freescale Semiconductor Chapter 13 Enhanced Serial Communications Interface (ESCI) Module 13.1 Introduction The enhanced serial communications interface (ESCI) module allows asynchronous communications with peripheral devices and other microcontroller units (MCU). 13.2 Features Features include: * Full-duplex operation * Standard mark/space non-return-to-zero (NRZ) format * Programmable baud rates * Programmable 8-bit or 9-bit character length * Separately enabled transmitter and receiver * Separate receiver and transmitter central processor unit (CPU) interrupt requests * Programmable transmitter output polarity * Two receiver wakeup methods: - Idle line wakeup - Address mark wakeup * Interrupt-driven operation with eight interrupt flags: - Transmitter empty - Transmission complete - Receiver full - Idle receiver input - Receiver overrun - Noise error - Framing error - Parity error * Receiver framing error detection * Hardware parity checking * 1/16 bit-time noise detection MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 151 Enhanced Serial Communications Interface (ESCI) Module INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTE5-PTE2 PTE1/RxD PTE0/TxD PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) DDRF CGMXFC CLOCK GENERATOR MODULE PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 13-1. Block Diagram Highlighting ESCI Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 152 Freescale Semiconductor Pin Name Conventions 13.3 Pin Name Conventions The generic names of the ESCI input/output (I/O) pins are: * RxD (receive data) * TxD (transmit data) ESCI I/O lines are implemented by sharing parallel I/O port pins. The full name of an ESCI input or output reflects the name of the shared port pin. Table 13-1 shows the full names and the generic names of the ESCI I/O pins. The generic pin names appear in the text of this section. Table 13-1. Pin Name Conventions Generic Pin Names Full Pin Names RxD TxD PTE1/RxD PTE0/TxD 13.4 Functional Description Figure 13-3 shows the structure of the ESCI module. The ESCI allows full-duplex, asynchronous, NRZ serial communication between the MCU and remote devices, including other MCUs. The transmitter and receiver of the ESCI operate independently, although they use the same baud rate generator. During normal operation, the CPU monitors the status of the ESCI, writes the data to be transmitted, and processes received data. The baud rate clock source for the ESCI can be selected via the configuration bit, SCIBDSRC, of the CONFIG2 register ($001E) For reference, a summary of the ESCI module input/output registers is provided in Figure 13-4. 13.4.1 Data Format The SCI uses the standard non-return-to-zero mark/space data format illustrated in Figure 13-2. START BIT START BIT 8-BIT DATA FORMAT (BIT M IN SCC1 CLEAR) BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 PARITY OR DATA BIT BIT 7 PARITY OR DATA BIT 9-BIT DATA FORMAT (BIT M IN SCC1 SET) BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 STOP BIT BIT 6 BIT 7 BIT 8 NEXT START BIT NEXT START BIT STOP BIT Figure 13-2. SCI Data Formats MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 153 Enhanced Serial Communications Interface (ESCI) Module INTERNAL BUS SCI_TxD SCTIE BUS CLOCK R8 TCIE SL T8 SCRIE ILIE TE ACLK BIT IN SCIACTL SCTE RE TxD TRANSMIT SHIFT REGISTER TXINV LINR RxD ARBITER RxD ERROR INTERRUPT CONTROL RECEIVE SHIFT REGISTER ESCI DATA REGISTER RECEIVER INTERRUPT CONTROL TRANSMITTER INTERRUPT CONTROL ESCI DATA REGISTER SBK SCRF OR ORIE IDLE NF NEIE FE FEIE PE SCI_CLK TC RWU PEIE LOOPS LOOPS WAKEUP CONTROL BUS CLOCK CGMXCLK RECEIVE CONTROL ENSCI ENHANCED PRESCALER SCIBDSRC FROM CONFIG2 TRANSMIT CONTROL FLAG CONTROL BKF M RPF WAKE LINT ILTY /4 SL ENSCI PRESCALER BAUD RATE GENERATOR / 16 PEN PTY DATA SELECTION CONTROL SL = 1 -> SCI_CLK = BUSCLK SL = 0 -> SCI_CLK = CGMXCLK Figure 13-3. ESCI Module Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 154 Freescale Semiconductor Functional Description Addr. $0009 $000A $000B $0013 $0014 $0015 $0016 $0017 $0018 $0019 Register Name Read: ESCI Prescaler Register (SCPSC) Write: See page 175. Reset: Read: ESCI Arbiter Control Register (SCIACTL) Write: See page 179. Reset: Read: ESCI Arbiter Data Register (SCIADAT) Write: See page 180. Reset: Read: ESCI Control Register 1 (SCC1) Write: See page 166. Reset: Read: ESCI Control Register 2 (SCC2) Write: See page 168. Reset: Bit 7 6 5 4 3 2 1 Bit 0 PDS2 PDS1 PDS0 PSSB4 PSSB3 PSSB2 PSSB1 PSSB0 0 0 0 0 0 0 0 0 AM0 ACLK AFIN ARUN AROVFL ARD8 AM1 ALOST 0 0 0 0 0 0 0 0 ARD7 ARD6 ARD5 ARD4 ARD3 ARD2 ARD1 ARD0 0 0 0 0 0 0 0 0 LOOPS ENSCI TXINV M WAKE ILTY PEN PTY 0 0 0 0 0 0 0 0 SCTIE TCIE SCRIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 T8 R R ORIE NEIE FEIE PEIE Read: ESCI Control Register 3 (SCC3) Write: See page 169. Reset: R8 U 0 0 0 0 0 0 0 Read: ESCI Status Register 1 (SCS1) Write: See page 170. Reset: SCTE TC SCRF IDLE OR NF FE PE 1 1 0 0 0 0 0 0 Read: ESCI Status Register 2 (SCS2) Write: See page 173. Reset: 0 0 0 0 0 0 BKF RPF 0 0 0 0 0 0 0 0 R7 R6 R5 R4 R3 R2 R1 R0 T7 T6 T5 T4 T3 T2 T1 T0 Read: ESCI Data Register (SCDR) Write: See page 173. Reset: Read: ESCI Baud Rate Register (SCBR) Write: See page 174. Reset: Unaffected by reset LINT LINR SCP1 SCP0 R SCR2 SCR1 SCR0 0 0 0 0 0 0 0 0 R = Reserved = Unimplemented Figure 13-4. ESCI I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 155 Enhanced Serial Communications Interface (ESCI) Module 13.4.2 Transmitter Figure 13-5 shows the structure of the SCI transmitter and the registers are summarized in Figure 13-4. The baud rate clock source for the ESCI can be selected via the configuration bit, SCIBDSRC. INTERNAL BUS PRESCALER BAUD DIVIDER / 16 ESCI DATA REGISTER SCP1 11-BIT TRANSMIT SHIFT REGISTER STOP SCP0 SCR2 H SCR1 8 7 6 5 4 3 2 START /4 1 0 L SCI_TxD TXINV PTY PARITY GENERATION PSSB4 PSSB3 T8 PSSB2 BREAK (ALL ZEROS) PDS0 PREAMBLE (ALL ONES) PEN SHIFT ENABLE PDS1 LOAD FROM SCDR M PDS2 CGMXCLK OR BUS CLOCK MSB PRESCALER SCR0 TRANSMITTER CONTROL LOGIC PSSB1 PSSB0 TRANSMITTER CPU INTERRUPT REQUEST SCTE SCTE SCTIE TC TCIE SBK LOOPS SCTIE ENSCI TC TE TCIE LINT Figure 13-5. ESCI Transmitter 13.4.2.1 Character Length The transmitter can accommodate either 8-bit or 9-bit data. The state of the M bit in ESCI control register 1 (SCC1) determines character length. When transmitting 9-bit data, bit T8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). 13.4.2.2 Character Transmission During an ESCI transmission, the transmit shift register shifts a character out to the TxD pin. The ESCI data register (SCDR) is the write-only buffer between the internal data bus and the transmit shift register. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 156 Freescale Semiconductor Functional Description To initiate an ESCI transmission: 1. Enable the ESCI by writing a 1 to the enable ESCI bit (ENSCI) in ESCI control register 1 (SCC1). 2. Enable the transmitter by writing a 1 to the transmitter enable bit (TE) in ESCI control register 2 (SCC2). 3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status register 1 (SCS1) and then writing to the SCDR. For 9-bit data, also write the T8 bit in SCC3. 4. Repeat step 3 for each subsequent transmission. At the start of a transmission, transmitter control logic automatically loads the transmit shift register with a preamble of 1s. After the preamble shifts out, control logic transfers the SCDR data into the transmit shift register. A 0 start bit automatically goes into the least significant bit (LSB) position of the transmit shift register. A 1 stop bit goes into the most significant bit (MSB) position. The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR transfers a byte to the transmit shift register. The SCTE bit indicates that the SCDR can accept new data from the internal data bus. If the ESCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a transmitter CPU interrupt request. When the transmit shift register is not transmitting a character, the TxD pin goes to the idle condition, high. If at any time software clears the ENSCI bit in ESCI control register 1 (SCC1), the transmitter and receiver relinquish control of the port E pins. 13.4.2.3 Break Characters Writing a 1 to the send break bit, SBK, in SCC2 loads the transmit shift register with a break character. For TXINV = 0 (output not inverted), a transmitted break character contains all 0s and has no start, stop, or parity bit. Break character length depends on the M bit in SCC1 and the LINR bits in SCBR. As long as SBK is at 1, transmitter logic continuously loads break characters into the transmit shift register. After software clears the SBK bit, the shift register finishes transmitting the last break character and then transmits at least one 1. The automatic 1 at the end of a break character guarantees the recognition of the start bit of the next character. When LINR is cleared in SCBR, the ESCI recognizes a break character when a start bit is followed by eight or nine 0 data bits and a 0 where the stop bit should be, resulting in a total of 10 or 11 consecutive 0 data bits. When LINR is set in SCBR, the ESCI recognizes a break character when a start bit is followed by 9 or 10 0 data bits and a 0 where the stop bit should be, resulting in a total of 11 or 12 consecutive 0 data bits. Receiving a break character has these effects on ESCI registers: * Sets the framing error bit (FE) in SCS1 * Sets the ESCI receiver full bit (SCRF) in SCS1 * Clears the ESCI data register (SCDR) * Clears the R8 bit in SCC3 * Sets the break flag bit (BKF) in SCS2 * May set the overrun (OR), noise flag (NF), parity error (PE), or reception in progress flag (RPF) bits MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 157 Enhanced Serial Communications Interface (ESCI) Module 13.4.2.4 Idle Characters For TXINV = 0 (output not inverted), a transmitted idle character contains all 1s and has no start, stop, or parity bit. Idle character length depends on the M bit in SCC1. The preamble is a synchronizing idle character that begins every transmission. If the TE bit is cleared during a transmission, the TxD pin becomes idle after completion of the transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle character to be sent after the character currently being transmitted. NOTE When a break sequence is followed immediately by an idle character, this SCI design exhibits a condition in which the break character length is reduced by one half bit time. In this instance, the break sequence will consist of a valid start bit, eight or nine data bits (as defined by the M bit in SCC1) of 0 and one half data bit length of 0 in the stop bit position followed immediately by the idle character. To ensure a break character of the proper length is transmitted, always queue up a byte of data to be transmitted while the final break sequence is in progress. When queueing an idle character, return the TE bit to 1 before the stop bit of the current character shifts out to the TxD pin. Setting TE after the stop bit appears on TxD causes data previously written to the SCDR to be lost. A good time to toggle the TE bit for a queued idle character is when the SCTE bit becomes set and just before writing the next byte to the SCDR. 13.4.2.5 Inversion of Transmitted Output The transmit inversion bit (TXINV) in ESCI control register 1 (SCC1) reverses the polarity of transmitted data. All transmitted values including idle, break, start, and stop bits, are inverted when TXINV is at 1. See 13.8.1 ESCI Control Register 1. 13.4.2.6 Transmitter Interrupts These conditions can generate CPU interrupt requests from the ESCI transmitter: * ESCI transmitter empty (SCTE) -- The SCTE bit in SCS1 indicates that the SCDR has transferred a character to the transmit shift register. SCTE can generate a transmitter CPU interrupt request. Setting the ESCI transmit interrupt enable bit, SCTIE, in SCC2 enables the SCTE bit to generate transmitter CPU interrupt requests. * Transmission complete (TC) -- The TC bit in SCS1 indicates that the transmit shift register and the SCDR are empty and that no break or idle character has been generated. The transmission complete interrupt enable bit, TCIE, in SCC2 enables the TC bit to generate transmitter CPU interrupt requests. 13.4.3 Receiver Figure 13-6 shows the structure of the ESCI receiver. The receiver I/O registers are summarized in Figure 13-4. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 158 Freescale Semiconductor Functional Description INTERNAL BUS SCP1 SCR1 SCP0 SCR0 DATA RECOVERY PDS2 ALL ZEROS RPF PDS1 PDS0 PSSB4 PSSB3 PSSB2 11-BIT RECEIVE SHIFT REGISTER STOP / 16 RxD BKF CGMXCLK OR BUS CLOCK BAUD DIVIDER H ALL ONES PRESCALER PRESCALER /4 ESCI DATA REGISTER 8 7 6 M WAKE ILTY PSSB1 PEN PSSB0 PTY PARITY CHECKING SCRF SCRIE OR ORIE NF NEIE ERROR CPU INTERRUPT REQUEST 5 4 3 2 SCRF WAKEUP LOGIC IDLE ILIE CPU INTERRUPT REQUEST START SCR2 1 0 L MSB LINR FE FEIE PE PEIE RWU IDLE R8 ILIE SCRIE OR ORIE NF NEIE FE FEIE PE PEIE Figure 13-6. ESCI Receiver Block Diagram 13.4.3.1 Character Length The receiver can accommodate either 8-bit or 9-bit data. The state of the M bit in ESCI control register 1 (SCC1) determines character length. When receiving 9-bit data, bit R8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). When receiving 8-bit data, bit R8 is a copy of the eighth bit (bit 7). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 159 Enhanced Serial Communications Interface (ESCI) Module 13.4.3.2 Character Reception During an ESCI reception, the receive shift register shifts characters in from the RxD pin. The ESCI data register (SCDR) is the read-only buffer between the internal data bus and the receive shift register. After a complete character shifts into the receive shift register, the data portion of the character transfers to the SCDR. The ESCI receiver full bit, SCRF, in ESCI status register 1 (SCS1) becomes set, indicating that the received byte can be read. If the ESCI receive interrupt enable bit, SCRIE, in SCC2 is also set, the SCRF bit generates a receiver CPU interrupt request. 13.4.3.3 Data Sampling The receiver samples the RxD pin at the RT clock rate. The RT clock is an internal signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch, the RT clock is resynchronized at these times (see Figure 13-7): * After every start bit * After the receiver detects a data bit change from 1 to 0 (after the majority of data bit samples at RT8, RT9, and RT10 returns a valid 1 and the majority of the next RT8, RT9, and RT10 samples returns a valid 0) To locate the start bit, data recovery logic does an asynchronous search for a 0 preceded by three 1s. When the falling edge of a possible start bit occurs, the RT clock begins to count to 16. SAMPLES LSB START BIT RxD START BIT QUALIFICATION START BIT DATA VERIFICATION SAMPLING RT CLOCK STATE RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT2 RT3 RT4 RT5 RT6 RT7 RT8 RT9 RT10 RT11 RT12 RT13 RT14 RT15 RT16 RT1 RT2 RT3 RT4 RT CLOCK RT CLOCK RESET Figure 13-7. Receiver Data Sampling To verify the start bit and to detect noise, data recovery logic takes samples at RT3, RT5, and RT7. Table 13-2 summarizes the results of the start bit verification samples. Table 13-2. Start Bit Verification RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag 000 Yes 0 001 Yes 1 010 Yes 1 011 No 0 100 Yes 1 101 No 0 110 No 0 111 No 0 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 160 Freescale Semiconductor Functional Description If start bit verification is not successful, the RT clock is reset and a new search for a start bit begins. To determine the value of a data bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 13-3 summarizes the results of the data bit samples. Table 13-3. Data Bit Recovery RT8, RT9, and RT10 Samples Data Bit Determination Noise Flag 000 0 0 001 0 1 010 0 1 011 1 1 100 0 1 101 1 1 110 1 1 111 1 0 NOTE The RT8, RT9, and RT10 samples do not affect start bit verification. If any or all of the RT8, RT9, and RT10 start bit samples are 1s following a successful start bit verification, the noise flag (NF) is set and the receiver assumes that the bit is a start bit. To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 13-4 summarizes the results of the stop bit samples. Table 13-4. Stop Bit Recovery RT8, RT9, and RT10 Samples Framing Error Flag Noise Flag 000 1 0 001 1 1 010 1 1 011 0 1 100 1 1 101 0 1 110 0 1 111 0 0 13.4.3.4 Framing Errors If the data recovery logic does not detect a 1 where the stop bit should be in an incoming character, it sets the framing error bit, FE, in SCS1. A break character also sets the FE bit because a break character has no stop bit. The FE bit is set at the same time that the SCRF bit is set. 13.4.3.5 Baud Rate Tolerance A transmitting device may be operating at a baud rate below or above the receiver baud rate. Accumulated bit time misalignment can cause one of the three stop bit data samples to fall outside the MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 161 Enhanced Serial Communications Interface (ESCI) Module actual stop bit. Then a noise error occurs. If more than one of the samples is outside the stop bit, a framing error occurs. In most applications, the baud rate tolerance is much more than the degree of misalignment that is likely to occur. As the receiver samples an incoming character, it resynchronizes the RT clock on any valid falling edge within the character. Resynchronization within characters corrects misalignments between transmitter bit times and receiver bit times. Slow Data Tolerance Figure 13-8 shows how much a slow received character can be misaligned without causing a noise error or a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and RT10. MSB STOP RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RECEIVER RT CLOCK DATA SAMPLES Figure 13-8. Slow Data For an 8-bit character, data sampling of the stop bit takes the receiver 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned character shown in Figure 13-8, the receiver counts 154 RT cycles at the point when the count of the transmitting device is 9 bit times x 16 RT cycles + 3 RT cycles = 147 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a slow 8-bit character with no errors is: 154 - 147 -------------------------- x 100 = 4.54% 154 For a 9-bit character, data sampling of the stop bit takes the receiver 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned character shown in Figure 13-8, the receiver counts 170 RT cycles at the point when the count of the transmitting device is 10 bit times x 16 RT cycles + 3 RT cycles = 163 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a slow 9-bit character with no errors is: 170 - 163 -------------------------- x 100 = 4.12% 170 Fast Data Tolerance Figure 13-9 shows how much a fast received character can be misaligned without causing a noise error or a framing error. The fast stop bit ends at RT10 instead of RT16 but is still there for the stop bit data samples at RT8, RT9, and RT10. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 162 Freescale Semiconductor Functional Description STOP IDLE OR NEXT CHARACTER RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RECEIVER RT CLOCK DATA SAMPLES Figure 13-9. Fast Data For an 8-bit character, data sampling of the stop bit takes the receiver 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned character shown in Figure 13-9, the receiver counts 154 RT cycles at the point when the count of the transmitting device is 10 bit times x 16 RT cycles = 160 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 8-bit character with no errors is 154 - 160 -------------------------- x 100 = 3.90%. 154 For a 9-bit character, data sampling of the stop bit takes the receiver 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned character shown in Figure 13-9, the receiver counts 170 RT cycles at the point when the count of the transmitting device is 11 bit times x 16 RT cycles = 176 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 9-bit character with no errors is: 170 - 176 -------------------------- x 100 = 3.53%. 170 13.4.3.6 Receiver Wakeup So that the MCU can ignore transmissions intended only for other receivers in multiple-receiver systems, the receiver can be put into a standby state. Setting the receiver wakeup bit, RWU, in SCC2 puts the receiver into a standby state during which receiver interrupts are disabled. Depending on the state of the WAKE bit in SCC1, either of two conditions on the RxD pin can bring the receiver out of the standby state: 1. Address mark -- An address mark is a 1 in the MSB position of a received character. When the WAKE bit is set, an address mark wakes the receiver from the standby state by clearing the RWU bit. The address mark also sets the ESCI receiver full bit, SCRF. Software can then compare the character containing the address mark to the user-defined address of the receiver. If they are the same, the receiver remains awake and processes the characters that follow. If they are not the same, software can set the RWU bit and put the receiver back into the standby state. 2. Idle input line condition -- When the WAKE bit is clear, an idle character on the RxD pin wakes the receiver from the standby state by clearing the RWU bit. The idle character that wakes the receiver does not set the receiver idle bit, IDLE, or the ESCI receiver full bit, SCRF. The idle line type bit, ILTY, determines whether the receiver begins counting 1s as idle character bits after the start bit or after the stop bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 163 Enhanced Serial Communications Interface (ESCI) Module NOTE With the WAKE bit clear, setting the RWU bit after the RxD pin has been idle will cause the receiver to wake up. 13.4.3.7 Receiver Interrupts These sources can generate CPU interrupt requests from the ESCI receiver: * ESCI receiver full (SCRF) -- The SCRF bit in SCS1 indicates that the receive shift register has transferred a character to the SCDR. SCRF can generate a receiver CPU interrupt request. Setting the ESCI receive interrupt enable bit, SCRIE, in SCC2 enables the SCRF bit to generate receiver CPU interrupts. * Idle input (IDLE) -- The IDLE bit in SCS1 indicates that 10 or 11 consecutive 1s shifted in from the RxD pin. The idle line interrupt enable bit, ILIE, in SCC2 enables the IDLE bit to generate CPU interrupt requests. 13.4.3.8 Error Interrupts These receiver error flags in SCS1 can generate CPU interrupt requests: * Receiver overrun (OR) -- The OR bit indicates that the receive shift register shifted in a new character before the previous character was read from the SCDR. The previous character remains in the SCDR, and the new character is lost. The overrun interrupt enable bit, ORIE, in SCC3 enables OR to generate ESCI error CPU interrupt requests. * Noise flag (NF) -- The NF bit is set when the ESCI detects noise on incoming data or break characters, including start, data, and stop bits. The noise error interrupt enable bit, NEIE, in SCC3 enables NF to generate ESCI error CPU interrupt requests. * Framing error (FE) -- The FE bit in SCS1 is set when a 0 occurs where the receiver expects a stop bit. The framing error interrupt enable bit, FEIE, in SCC3 enables FE to generate ESCI error CPU interrupt requests. * Parity error (PE) -- The PE bit in SCS1 is set when the ESCI detects a parity error in incoming data. The parity error interrupt enable bit, PEIE, in SCC3 enables PE to generate ESCI error CPU interrupt requests. 13.5 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 13.5.1 Wait Mode The ESCI module remains active in wait mode. Any enabled CPU interrupt request from the ESCI module can bring the MCU out of wait mode. If ESCI module functions are not required during wait mode, reduce power consumption by disabling the module before executing the WAIT instruction. 13.5.2 Stop Mode The ESCI module is inactive in stop mode. The STOP instruction does not affect ESCI register states. ESCI module operation resumes after the MCU exits stop mode. Because the internal clock is inactive during stop mode, entering stop mode during an ESCI transmission or reception results in invalid data. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 164 Freescale Semiconductor ESCI During Break Module Interrupts 13.6 ESCI During Break Module Interrupts The BCFE bit in the break flag control register (SBFCR) enables software to clear status bits during the break state. See 19.2 Break Module (BRK). To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a two-step read/write clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. 13.7 I/O Signals Port E shares two of its pins with the ESCI module. The two ESCI I/O pins are: * PTE0/TxD -- transmit data * PTE1/RxD -- receive data 13.7.1 PTE0/TxD (Transmit Data) The PTE0/TxD pin is the serial data output from the ESCI transmitter. The ESCI shares the PTE0/TxD pin with port E. When the ESCI is enabled, the PTE0/TxD pin is an output regardless of the state of the DDRE0 bit in data direction register E (DDRE). 13.7.2 PTE1/RxD (Receive Data) The PTE1/RxD pin is the serial data input to the ESCI receiver. The ESCI shares the PTE1/RxD pin with port E. When the ESCI is enabled, the PTE1/RxD pin is an input regardless of the state of the DDRE1 bit in data direction register E (DDRE). 13.8 I/O Registers These I/O registers control and monitor ESCI operation: * ESCI control register 1, SCC1 * ESCI control register 2, SCC2 * ESCI control register 3, SCC3 * ESCI status register 1, SCS1 * ESCI status register 2, SCS2 * ESCI data register, SCDR * ESCI baud rate register, SCBR * ESCI prescaler register, SCPSC * ESCI arbiter control register, SCIACTL * ESCI arbiter data register, SCIADAT MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 165 Enhanced Serial Communications Interface (ESCI) Module 13.8.1 ESCI Control Register 1 ESCI control register 1 (SCC1): * Enables loop mode operation * Enables the ESCI * Controls output polarity * Controls character length * Controls ESCI wakeup method * Controls idle character detection * Enables parity function * Controls parity type Address: $0013 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 LOOPS ENSCI TXINV M WAKE ILTY PEN PTY 0 0 0 0 0 0 0 0 Figure 13-10. ESCI Control Register 1 (SCC1) LOOPS -- Loop Mode Select Bit This read/write bit enables loop mode operation. In loop mode the RxD pin is disconnected from the ESCI, and the transmitter output goes into the receiver input. Both the transmitter and the receiver must be enabled to use loop mode. Reset clears the LOOPS bit. 1 = Loop mode enabled 0 = Normal operation enabled ENSCI -- Enable ESCI Bit This read/write bit enables the ESCI and the ESCI baud rate generator. Clearing ENSCI sets the SCTE and TC bits in ESCI status register 1 and disables transmitter interrupts. Reset clears the ENSCI bit. 1 = ESCI enabled 0 = ESCI disabled TXINV -- Transmit Inversion Bit This read/write bit reverses the polarity of transmitted data. Reset clears the TXINV bit. 1 = Transmitter output inverted 0 = Transmitter output not inverted NOTE Setting the TXINV bit inverts all transmitted values including idle, break, start, and stop bits. M -- Mode (Character Length) Bit This read/write bit determines whether ESCI characters are eight or nine bits long (See Table 13-5).The ninth bit can serve as a receiver wakeup signal or as a parity bit. Reset clears the M bit. 1 = 9-bit ESCI characters 0 = 8-bit ESCI characters MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 166 Freescale Semiconductor I/O Registers Table 13-5. Character Format Selection Control Bits Character Format M PEN:PTY Start Bits Data Bits Parity Stop Bits Character Length 0 0 X 1 8 None 1 10 bits 1 0 X 1 9 None 1 11 bits 0 1 0 1 7 Even 1 10 bits 0 1 1 1 7 Odd 1 10 bits 1 1 0 1 8 Even 1 11 bits 1 1 1 1 8 Odd 1 11 bits WAKE -- Wakeup Condition Bit This read/write bit determines which condition wakes up the ESCI: a 1 (address mark) in the MSB position of a received character or an idle condition on the RxD pin. Reset clears the WAKE bit. 1 = Address mark wakeup 0 = Idle line wakeup ILTY -- Idle Line Type Bit This read/write bit determines when the ESCI starts counting 1s as idle character bits. The counting begins either after the start bit or after the stop bit. If the count begins after the start bit, then a string of 1s preceding the stop bit may cause false recognition of an idle character. Beginning the count after the stop bit avoids false idle character recognition, but requires properly synchronized transmissions. Reset clears the ILTY bit. 1 = Idle character bit count begins after stop bit 0 = Idle character bit count begins after start bit PEN -- Parity Enable Bit This read/write bit enables the ESCI parity function (see Table 13-5). When enabled, the parity function inserts a parity bit in the MSB position (see Table 13-3). Reset clears the PEN: bit. 1 = Parity function enabled 0 = Parity function disabled PTY -- Parity Bit This read/write bit determines whether the ESCI generates and checks for odd parity or even parity (see Table 13-5). Reset clears the PTY bit. 1 = Odd parity 0 = Even parity NOTE Changing the PTY bit in the middle of a transmission or reception can generate a parity error. 13.8.2 ESCI Control Register 2 ESCI control register 2 (SCC2): * Enables these CPU interrupt requests: - SCTE bit to generate transmitter CPU interrupt requests - TC bit to generate transmitter CPU interrupt requests - SCRF bit to generate receiver CPU interrupt requests - IDLE bit to generate receiver CPU interrupt requests MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 167 Enhanced Serial Communications Interface (ESCI) Module * * * * Enables the transmitter Enables the receiver Enables ESCI wakeup Transmits ESCI break characters Address: $0014 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 SCTIE TCIE SCRIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 Figure 13-11. ESCI Control Register 2 (SCC2) SCTIE -- ESCI Transmit Interrupt Enable Bit This read/write bit enables the SCTE bit to generate ESCI transmitter CPU interrupt requests. Setting the SCTIE bit in SCC2 enables the SCTE bit to generate CPU interrupt requests. Reset clears the SCTIE bit. 1 = SCTE enabled to generate CPU interrupt 0 = SCTE not enabled to generate CPU interrupt TCIE -- Transmission Complete Interrupt Enable Bit This read/write bit enables the TC bit to generate ESCI transmitter CPU interrupt requests. Reset clears the TCIE bit. 1 = TC enabled to generate CPU interrupt requests 0 = TC not enabled to generate CPU interrupt requests SCRIE -- ESCI Receive Interrupt Enable Bit This read/write bit enables the SCRF bit to generate ESCI receiver CPU interrupt requests. Setting the SCRIE bit in SCC2 enables the SCRF bit to generate CPU interrupt requests. Reset clears the SCRIE bit. 1 = SCRF enabled to generate CPU interrupt 0 = SCRF not enabled to generate CPU interrupt ILIE -- Idle Line Interrupt Enable Bit This read/write bit enables the IDLE bit to generate ESCI receiver CPU interrupt requests. Reset clears the ILIE bit. 1 = IDLE enabled to generate CPU interrupt requests 0 = IDLE not enabled to generate CPU interrupt requests TE -- Transmitter Enable Bit Setting this read/write bit begins the transmission by sending a preamble of 10 or 11 1s from the transmit shift register to the TxD pin. If software clears the TE bit, the transmitter completes any transmission in progress before the TxD returns to the idle condition (high). Clearing and then setting TE during a transmission queues an idle character to be sent after the character currently being transmitted. Reset clears the TE bit. 1 = Transmitter enabled 0 = Transmitter disabled NOTE Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is clear. ENSCI is in ESCI control register 1. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 168 Freescale Semiconductor I/O Registers RE -- Receiver Enable Bit Setting this read/write bit enables the receiver. Clearing the RE bit disables the receiver but does not affect receiver interrupt flag bits. Reset clears the RE bit. 1 = Receiver enabled 0 = Receiver disabled NOTE Writing to the RE bit is not allowed when the enable ESCI bit (ENSCI) is clear. ENSCI is in ESCI control register 1. RWU -- Receiver Wakeup Bit This read/write bit puts the receiver in a standby state during which receiver interrupts are disabled. The WAKE bit in SCC1 determines whether an idle input or an address mark brings the receiver out of the standby state and clears the RWU bit. Reset clears the RWU bit. 1 = Standby state 0 = Normal operation SBK -- Send Break Bit Setting and then clearing this read/write bit transmits a break character followed by a 1. The 1 after the break character guarantees recognition of a valid start bit. If SBK remains set, the transmitter continuously transmits break characters with no 1s between them. Reset clears the SBK bit. 1 = Transmit break characters 0 = No break characters being transmitted NOTE Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling SBK before the preamble begins causes the ESCI to send a break character instead of a preamble. 13.8.3 ESCI Control Register 3 ESCI control register 3 (SCC3): * Stores the ninth ESCI data bit received and the ninth ESCI data bit to be transmitted. * Enables these interrupts: - Receiver overrun - Noise error - Framing error - Parity error Address: $0015 Bit 7 Read: R8 Write: Reset: U 6 5 4 3 2 1 Bit 0 T8 R R ORIE NEIE FEIE PEIE 0 0 0 0 0 = Unimplemented 0 0 R = Reserved U = Unaffected Figure 13-12. ESCI Control Register 3 (SCC3) R8 -- Received Bit 8 When the ESCI is receiving 9-bit characters, R8 is the read-only ninth bit (bit 8) of the received character. R8 is received at the same time that the SCDR receives the other 8 bits. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 169 Enhanced Serial Communications Interface (ESCI) Module When the ESCI is receiving 8-bit characters, R8 is a copy of the eighth bit (bit 7). Reset has no effect on the R8 bit. T8 -- Transmitted Bit 8 When the ESCI is transmitting 9-bit characters, T8 is the read/write ninth bit (bit 8) of the transmitted character. T8 is loaded into the transmit shift register at the same time that the SCDR is loaded into the transmit shift register. Reset clears the T8 bit. ORIE -- Receiver Overrun Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the receiver overrun bit, OR. Reset clears ORIE. 1 = ESCI error CPU interrupt requests from OR bit enabled 0 = ESCI error CPU interrupt requests from OR bit disabled NEIE -- Receiver Noise Error Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the noise error bit, NE. Reset clears NEIE. 1 = ESCI error CPU interrupt requests from NE bit enabled 0 = ESCI error CPU interrupt requests from NE bit disabled FEIE -- Receiver Framing Error Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the framing error bit, FE. Reset clears FEIE. 1 = ESCI error CPU interrupt requests from FE bit enabled 0 = ESCI error CPU interrupt requests from FE bit disabled PEIE -- Receiver Parity Error Interrupt Enable Bit This read/write bit enables ESCI receiver CPU interrupt requests generated by the parity error bit, PE. Reset clears PEIE. 1 = ESCI error CPU interrupt requests from PE bit enabled 0 = ESCI error CPU interrupt requests from PE bit disabled 13.8.4 ESCI Status Register 1 ESCI status register 1 (SCS1) contains flags to signal these conditions: * Transfer of SCDR data to transmit shift register complete * Transmission complete * Transfer of receive shift register data to SCDR complete * Receiver input idle * Receiver overrun * Noisy data * Framing error * Parity error Address: Read: $0016 Bit 7 6 5 4 3 2 1 Bit 0 SCTE TC SCRF IDLE OR NF FE PE 1 0 0 0 0 0 0 Write: Reset: 1 = Unimplemented Figure 13-13. ESCI Status Register 1 (SCS1) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 170 Freescale Semiconductor I/O Registers SCTE -- ESCI Transmitter Empty Bit This clearable, read-only bit is set when the SCDR transfers a character to the transmit shift register. SCTE can generate an ESCI transmitter CPU interrupt request. When the SCTIE bit in SCC2 is set, SCTE generates an ESCI transmitter CPU interrupt request. In normal operation, clear the SCTE bit by reading SCS1 with SCTE set and then writing to SCDR. Reset sets the SCTE bit. 1 = SCDR data transferred to transmit shift register 0 = SCDR data not transferred to transmit shift register TC -- Transmission Complete Bit This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being transmitted. TC generates an ESCI transmitter CPU interrupt request if the TCIE bit in SCC2 is also set. TC is cleared automatically when data, preamble, or break is queued and ready to be sent. There may be up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the transmission actually starting. Reset sets the TC bit. 1 = No transmission in progress 0 = Transmission in progress SCRF -- ESCI Receiver Full Bit This clearable, read-only bit is set when the data in the receive shift register transfers to the ESCI data register. SCRF can generate an ESCI receiver CPU interrupt request. When the SCRIE bit in SCC2 is set the SCRF generates a CPU interrupt request. In normal operation, clear the SCRF bit by reading SCS1 with SCRF set and then reading the SCDR. Reset clears SCRF. 1 = Received data available in SCDR 0 = Data not available in SCDR IDLE -- Receiver Idle Bit This clearable, read-only bit is set when 10 or 11 consecutive 1s appear on the receiver input. IDLE generates an ESCI receiver CPU interrupt request if the ILIE bit in SCC2 is also set. Clear the IDLE bit by reading SCS1 with IDLE set and then reading the SCDR. After the receiver is enabled, it must receive a valid character that sets the SCRF bit before an idle condition can set the IDLE bit. Also, after the IDLE bit has been cleared, a valid character must again set the SCRF bit before an idle condition can set the IDLE bit. Reset clears the IDLE bit. 1 = Receiver input idle 0 = Receiver input active (or idle since the IDLE bit was cleared) OR -- Receiver Overrun Bit This clearable, read-only bit is set when software fails to read the SCDR before the receive shift register receives the next character. The OR bit generates an ESCI error CPU interrupt request if the ORIE bit in SCC3 is also set. The data in the shift register is lost, but the data already in the SCDR is not affected. Clear the OR bit by reading SCS1 with OR set and then reading the SCDR. Reset clears the OR bit. 1 = Receive shift register full and SCRF = 1 0 = No receiver overrun Software latency may allow an overrun to occur between reads of SCS1 and SCDR in the flag-clearing sequence. Figure 13-14 shows the normal flag-clearing sequence and an example of an overrun caused by a delayed flag-clearing sequence. The delayed read of SCDR does not clear the OR bit because OR was not set when SCS1 was read. Byte 2 caused the overrun and is lost. The next flag-clearing sequence reads byte 3 in the SCDR instead of byte 2. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 171 Enhanced Serial Communications Interface (ESCI) Module BYTE 1 BYTE 2 BYTE 3 SCRF = 0 SCRF = 1 SCRF = 0 SCRF = 1 SCRF = 0 SCRF = 1 NORMAL FLAG CLEARING SEQUENCE BYTE 4 READ SCS1 SCRF = 1 OR = 0 READ SCS1 SCRF = 1 OR = 0 READ SCS1 SCRF = 1 OR = 0 READ SCDR BYTE 1 READ SCDR BYTE 2 READ SCDR BYTE 3 BYTE 1 BYTE 2 BYTE 3 SCRF = 0 OR = 0 SCRF = 1 OR = 1 SCRF = 0 OR = 1 SCRF = 1 SCRF = 1 OR = 1 DELAYED FLAG CLEARING SEQUENCE BYTE 4 READ SCS1 SCRF = 1 OR = 0 READ SCS1 SCRF = 1 OR = 1 READ SCDR BYTE 1 READ SCDR BYTE 3 Figure 13-14. Flag Clearing Sequence In applications that are subject to software latency or in which it is important to know which byte is lost due to an overrun, the flag-clearing routine can check the OR bit in a second read of SCS1 after reading the data register. NF -- Receiver Noise Flag Bit This clearable, read-only bit is set when the ESCI detects noise on the RxD pin. NF generates an NF CPU interrupt request if the NEIE bit in SCC3 is also set. Clear the NF bit by reading SCS1 and then reading the SCDR. Reset clears the NF bit. 1 = Noise detected 0 = No noise detected FE -- Receiver Framing Error Bit This clearable, read-only bit is set when a 0 is accepted as the stop bit. FE generates an ESCI error CPU interrupt request if the FEIE bit in SCC3 also is set. Clear the FE bit by reading SCS1 with FE set and then reading the SCDR. Reset clears the FE bit. 1 = Framing error detected 0 = No framing error detected PE -- Receiver Parity Error Bit This clearable, read-only bit is set when the ESCI detects a parity error in incoming data. PE generates a PE CPU interrupt request if the PEIE bit in SCC3 is also set. Clear the PE bit by reading SCS1 with PE set and then reading the SCDR. Reset clears the PE bit. 1 = Parity error detected 0 = No parity error detected MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 172 Freescale Semiconductor I/O Registers 13.8.5 ESCI Status Register 2 ESCI status register 2 (SCS2) contains flags to signal these conditions: * Break character detected * Incoming data Address: Read: $0017 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 BKF RPF 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 13-15. ESCI Status Register 2 (SCS2) BKF -- Break Flag Bit This clearable, read-only bit is set when the ESCI detects a break character on the RxD pin. In SCS1, the FE and SCRF bits are also set. In 9-bit character transmissions, the R8 bit in SCC3 is cleared. BKF does not generate a CPU interrupt request. Clear BKF by reading SCS2 with BKF set and then reading the SCDR. Once cleared, BKF can become set again only after 1s again appear on the RxD pin followed by another break character. Reset clears the BKF bit. 1 = Break character detected 0 = No break character detected RPF -- Reception in Progress Flag Bit This read-only bit is set when the receiver detects a 0 during the RT1 time period of the start bit search. RPF does not generate an interrupt request. RPF is reset after the receiver detects false start bits (usually from noise or a baud rate mismatch), or when the receiver detects an idle character. Polling RPF before disabling the ESCI module or entering stop mode can show whether a reception is in progress. 1 = Reception in progress 0 = No reception in progress 13.8.6 ESCI Data Register The ESCI data register (SCDR) is the buffer between the internal data bus and the receive and transmit shift registers. Reset has no effect on data in the ESCI data register. Address: $0018 Bit 7 6 5 4 3 2 1 Bit 0 Read: R7 R6 R5 R4 R3 R2 R1 R0 Write: T7 T6 T5 T4 T3 T2 T1 T0 Reset: Unaffected by reset Figure 13-16. ESCI Data Register (SCDR) R7/T7:R0/T0 -- Receive/Transmit Data Bits Reading address $0018 accesses the read-only received data bits, R7:R0. Writing to address $0018 writes the data to be transmitted, T7:T0. Reset has no effect on the ESCI data register. NOTE Do not use read-modify-write instructions on the ESCI data register. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 173 Enhanced Serial Communications Interface (ESCI) Module 13.8.7 ESCI Baud Rate Register The ESCI baud rate register (SCBR) together with the ESCI prescaler register selects the baud rate for both the receiver and the transmitter. NOTE There are two prescalers available to adjust the baud rate. One in the ESCI baud rate register and one in the ESCI prescaler register. Address: Read: Write: Reset: $0019 Bit 7 6 5 4 3 2 1 Bit 0 LINT LINR SCP1 SCP0 R SCR2 SCR1 SCR0 0 0 0 0 0 0 0 0 R = Reserved Figure 13-17. ESCI Baud Rate Register (SCBR) LINT -- LIN Transmit Enable This read/write bit selects the enhanced ESCI features for the local interconnect network (LIN) protocol as shown in Table 13-6. Reset clears LINT. LINR -- LIN Receiver Bits This read/write bit selects the enhanced ESCI features for the local interconnect network (LIN) protocol as shown in Table 13-6. Reset clears LINR. Table 13-6. ESCI LIN Control Bits LINT LINR M Functionality 0 0 X Normal ESCI functionality 0 1 0 11-bit break detect enabled for LIN receiver 0 1 1 12-bit break detect enabled for LIN receiver 1 0 0 13-bit generation enabled for LIN transmitter 1 0 1 14-bit generation enabled for LIN transmitter 1 1 0 11-bit break detect/13-bit generation enabled for LIN 1 1 1 12-bit break detect/14-bit generation enabled for LIN In LIN (version 1.2) systems, the master node transmits a break character which will appear as 11.05-14.95 dominant bits to the slave node. A data character of 0x00 sent from the master might appear as 7.65-10.35 dominant bit times. This is due to the oscillator tolerance requirement that the slave node must be within 15% of the master node's oscillator. Since a slave node cannot know if it is running faster or slower than the master node (prior to synchronization), the LINR bit allows the slave node to differentiate between a 0x00 character of 10.35 bits and a break character of 11.05 bits. The break symbol length must be verified in software in any case, but the LINR bit serves as a filter, preventing false detections of break characters that are really 0x00 data characters. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 174 Freescale Semiconductor I/O Registers SCP1 and SCP0 -- ESCI Baud Rate Register Prescaler Bits These read/write bits select the baud rate register prescaler divisor as shown in Table 13-7. Reset clears SCP1 and SCP0. Table 13-7. ESCI Baud Rate Prescaling SCP[1:0] Baud Rate Register Prescaler Divisor (BPD) 0 0 1 0 1 3 1 0 4 1 1 13 SCR2-SCR0 -- ESCI Baud Rate Select Bits These read/write bits select the ESCI baud rate divisor as shown in Table 13-8. Reset clears SCR2-SCR0. Table 13-8. ESCI Baud Rate Selection SCR[2:1:0] Baud Rate Divisor (BD) 0 0 0 1 0 0 1 2 0 1 0 4 0 1 1 8 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 13.8.8 ESCI Prescaler Register The ESCI prescaler register (SCPSC) together with the ESCI baud rate register selects the baud rate for both the receiver and the transmitter. NOTE There are two prescalers available to adjust the baud rate. One in the ESCI baud rate register and one in the ESCI prescaler register. ; Address: Read: Write: Reset: $0009 Bit 7 6 5 4 3 2 1 Bit 0 PDS2 PDS1 PDS0 PSSB4 PSSB3 PSSB2 PSSB1 PSSB0 0 0 0 0 0 0 0 0 Figure 13-18. ESCI Prescaler Register (SCPSC) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 175 Enhanced Serial Communications Interface (ESCI) Module PDS2-PDS0 -- Prescaler Divisor Select Bits These read/write bits select the prescaler divisor as shown in Table 13-9. Reset clears PDS2-PDS0. NOTE The setting of `000' will bypass this prescaler. It is not recommended to bypass the prescaler while ENSCI is set, because the switching is not glitch free. Table 13-9. ESCI Prescaler Division Ratio PDS[2:1:0] Prescaler Divisor (PD) 0 0 0 Bypass this prescaler 0 0 1 2 0 1 0 3 0 1 1 4 1 0 0 5 1 0 1 6 1 1 0 7 1 1 1 8 PSSB4-PSSB0 -- Clock Insertion Select Bits These read/write bits select the number of clocks inserted in each 32 output cycle frame to achieve more timing resolution on the average prescaler frequency as shown in Table 13-10. Reset clears PSSB4-PSSB0. Table 13-10. ESCI Prescaler Divisor Fine Adjust PSSB[4:3:2:1:0] Prescaler Divisor Fine Adjust (PDFA) 0 0 0 0 0 0/32 = 0 0 0 0 0 1 1/32 = 0.03125 0 0 0 1 0 2/32 = 0.0625 0 0 0 1 1 3/32 = 0.09375 0 0 1 0 0 4/32 = 0.125 0 0 1 0 1 5/32 = 0.15625 0 0 1 1 0 6/32 = 0.1875 0 0 1 1 1 7/32 = 0.21875 0 1 0 0 0 8/32 = 0.25 0 1 0 0 1 9/32 = 0.28125 0 1 0 1 0 10/32 = 0.3125 0 1 0 1 1 11/32 = 0.34375 0 1 1 0 0 12/32 = 0.375 0 1 1 0 1 13/32 = 0.40625 0 1 1 1 0 14/32 = 0.4375 0 1 1 1 1 15/32 = 0.46875 Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 176 Freescale Semiconductor ESCI Arbiter Table 13-10. ESCI Prescaler Divisor Fine Adjust (Continued) PSSB[4:3:2:1:0] Prescaler Divisor Fine Adjust (PDFA) 1 0 0 0 0 16/32 = 0.5 1 0 0 0 1 17/32 = 0.53125 1 0 0 1 0 18/32 = 0.5625 1 0 0 1 1 19/32 = 0.59375 1 0 1 0 0 20/32 = 0.625 1 0 1 0 1 21/32 = 0.65625 1 0 1 1 0 22/32 = 0.6875 1 0 1 1 1 23/32 = 0.71875 1 1 0 0 0 24/32 = 0.75 1 1 0 0 1 25/32 = 0.78125 1 1 0 1 0 26/32 = 0.8125 1 1 0 1 1 27/32 = 0.84375 1 1 1 0 0 28/32 = 0.875 1 1 1 0 1 29/32 = 0.90625 1 1 1 1 0 30/32 = 0.9375 1 1 1 1 1 31/32 = 0.96875 Use the following formula to calculate the ESCI baud rate: Baud rate = Frequency of the SCI clock source 64 x BPD x BD x (PD + PDFA) where: Frequency of the SCI clock source = fBus or CGMXCLK (selected by SCIBDSRC in the CONFIG2 register) BPD = Baud rate register prescaler divisor BD = Baud rate divisor PD = Prescaler divisor PDFA = Prescaler divisor fine adjust Table 13-11 shows the ESCI baud rates that can be generated with a 4.9152-MHz bus frequency. 13.9 ESCI Arbiter The ESCI module comprises an arbiter module designed to support software for communication tasks as bus arbitration, baud rate recovery and break time detection. The arbiter module consists of an 9-bit counter with 1-bit overflow and control logic. The CPU can control operation mode via the ESCI arbiter control register (SCIACTL). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 177 Enhanced Serial Communications Interface (ESCI) Module Table 13-11. ESCI Baud Rate Selection Examples PDS[2:1:0] PSSB[4:3:2:1:0] SCP[1:0] Prescaler Divisor (BPD) SCR[2:1:0] Baud Rate Divisor (BD) 0 0 0 X X X X X 0 0 1 0 0 0 1 76,800 1 1 1 0 0 0 0 0 0 0 1 0 0 0 1 9600 1 1 1 0 0 0 0 1 0 0 1 0 0 0 1 9562.65 1 1 1 0 0 0 1 0 0 0 1 0 0 0 1 9525.58 1 1 1 1 1 1 1 1 0 0 1 0 0 0 1 8563.07 0 0 0 X X X X X 0 0 1 0 0 1 2 38,400 0 0 0 X X X X X 0 0 1 0 1 0 4 19,200 0 0 0 X X X X X 0 0 1 0 1 1 8 9600 0 0 0 X X X X X 0 0 1 1 0 0 16 4800 0 0 0 X X X X X 0 0 1 1 0 1 32 2400 0 0 0 X X X X X 0 0 1 1 1 0 64 1200 0 0 0 X X X X X 0 0 1 1 1 1 128 600 0 0 0 X X X X X 0 1 3 0 0 0 1 25,600 0 0 0 X X X X X 0 1 3 0 0 1 2 12,800 0 0 0 X X X X X 0 1 3 0 1 0 4 6400 0 0 0 X X X X X 0 1 3 0 1 1 8 3200 0 0 0 X X X X X 0 1 3 1 0 0 16 1600 0 0 0 X X X X X 0 1 3 1 0 1 32 800 0 0 0 X X X X X 0 1 3 1 1 0 64 400 0 0 0 X X X X X 0 1 3 1 1 1 128 200 0 0 0 X X X X X 1 0 4 0 0 0 1 19,200 0 0 0 X X X X X 1 0 4 0 0 1 2 9600 0 0 0 X X X X X 1 0 4 0 1 0 4 4800 0 0 0 X X X X X 1 0 4 0 1 1 8 2400 0 0 0 X X X X X 1 0 4 1 0 0 16 1200 0 0 0 X X X X X 1 0 4 1 0 1 32 600 0 0 0 X X X X X 1 0 4 1 1 0 64 300 0 0 0 X X X X X 1 0 4 1 1 1 128 150 0 0 0 X X X X X 1 1 13 0 0 0 1 5908 0 0 0 X X X X X 1 1 13 0 0 1 2 2954 0 0 0 X X X X X 1 1 13 0 1 0 4 1477 0 0 0 X X X X X 1 1 13 0 1 1 8 739 0 0 0 X X X X X 1 1 13 1 0 0 16 369 0 0 0 X X X X X 1 1 13 1 0 1 32 185 0 0 0 X X X X X 1 1 13 1 1 0 64 92 0 0 0 X X X X X 1 1 13 1 1 1 128 46 Baud Rate (fBus= 4.9152 MHz) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 178 Freescale Semiconductor ESCI Arbiter 13.9.1 ESCI Arbiter Control Register Address: $000A Bit 7 Read: Write: Reset: AM1 0 6 ALOST 0 5 4 AM0 ACLK 0 0 3 2 1 Bit 0 AFIN ARUN AROVFL ARD8 0 0 0 0 = Unimplemented Figure 13-19. ESCI Arbiter Control Register (SCIACTL) AM1 and AM0 -- Arbiter Mode Select Bits These read/write bits select the mode of the arbiter module as shown in Table 13-12. Reset clears AM1 and AM0. Table 13-12. ESCI Arbiter Selectable Modes AM[1:0] ESCI Arbiter Mode 0 0 Idle / counter reset 0 1 Bit time measurement 1 0 Bus arbitration 1 1 Reserved / do not use ALOST -- Arbitration Lost Flag This read-only bit indicates loss of arbitration. Clear ALOST by writing a 0 to AM1. Reset clears ALOST. ACLK -- Arbiter Counter Clock Select Bit This read/write bit selects the arbiter counter clock source. Reset clears ACLK. 1 = Arbiter counter is clocked with one half of the ESCI input clock generated by the ESCI prescaler 0 = Arbiter counter is clocked with the bus clock divided by four NOTE For ACLK = 1, the arbiter input clock is driven from the ESCI prescaler. The prescaler can be clocked by either the bus clock or CGMXCLK depending on the state of the SCIBDSRC bit in CONFIG2. AFIN-- Arbiter Bit Time Measurement Finish Flag This read-only bit indicates bit time measurement has finished. Clear AFIN by writing any value to SCIACTL. Reset clears AFIN. 1 = Bit time measurement has finished 0 = Bit time measurement not yet finished ARUN-- Arbiter Counter Running Flag This read-only bit indicates the arbiter counter is running. Reset clears ARUN. 1 = Arbiter counter running 0 = Arbiter counter stopped MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 179 Enhanced Serial Communications Interface (ESCI) Module AROVFL-- Arbiter Counter Overflow Bit This read-only bit indicates an arbiter counter overflow. Clear AROVFL by writing any value to SCIACTL. Writing 0s to AM1 and AM0 resets the counter keeps it in this idle state. Reset clears AROVFL. 1 = Arbiter counter overflow has occurred 0 = No arbiter counter overflow has occurred ARD8-- Arbiter Counter MSB This read-only bit is the MSB of the 9-bit arbiter counter. Clear ARD8 by writing any value to SCIACTL. Reset clears ARD8. 13.9.2 ESCI Arbiter Data Register Address: $000B Read: Bit 7 6 5 4 3 2 1 Bit 0 ARD7 ARD6 ARD5 ARD4 ARD3 ARD2 ARD1 ARD0 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 13-20. ESCI Arbiter Data Register (SCIADAT) ARD7-ARD0 -- Arbiter Least Significant Counter Bits These read-only bits are the eight LSBs of the 9-bit arbiter counter. Clear ARD7-ARD0 by writing any value to SCIACTL. Writing 0s to AM1 and AM0 permanently resets the counter and keeps it in this idle state. Reset clears ARD7-ARD0. 13.9.3 Bit Time Measurement Two bit time measurement modes, described here, are available according to the state of ACLK. 1. ACLK = 0 -- The counter is clocked with the bus clock divided by four. The counter is started when a falling edge on the RxD pin is detected. The counter will be stopped on the next falling edge. ARUN is set while the counter is running, AFIN is set on the second falling edge on RxD (for instance, the counter is stopped). This mode is used to recover the received baud rate. See Figure 13-21. 2. ACLK = 1 -- The counter is clocked with one half of the ESCI input clock generated by the ESCI prescaler. The counter is started when a 0 is detected on RxD (see Figure 13-22). A 0 on RxD on enabling the bit time measurement with ACLK = 1 leads to immediate start of the counter (see Figure 13-23). The counter will be stopped on the next rising edge of RxD. This mode is used to measure the length of a received break. 13.9.4 Arbitration Mode If AM[1:0] is set to 10, the arbiter module operates in arbitration mode. On every rising edge of SCI_TxD (output of the ESCI module, internal chip signal), the counter is started. When the counter reaches $38 (ACLK = 0) or $08 (ACLK = 1), RxD is statically sensed. If in this case, RxD is sensed low (for example, another bus is driving the bus dominant) ALOST is set. As long as ALOST is set, the TxD pin is forced to 1, resulting in a seized transmission. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 180 Freescale Semiconductor ESCI Arbiter If SCI_TxD senses 0 without having sensed a 0 before on RxD, the counter will be reset, arbitration operation will be restarted after the next rising edge of SCI_TxD. MEASURED TIME CPU READS RESULT OUT OF SCIADAT COUNTER STOPS, AFIN = 1 COUNTER STARTS, ARUN = 1 CPU WRITES SCIACTL WITH $20 RXD Figure 13-21. Bit Time Measurement with ACLK = 0 MEASURED TIME CPU READS RESULT OUT OF SCIADAT CPU WRITES SCIACTL WITH $30 COUNTER STARTS, ARUN = 1 COUNTER STOPS, AFIN = 1 RXD Figure 13-22. Bit Time Measurement with ACLK = 1, Scenario A MEASURED TIME CPU READS RESULT OUT OF SCIADAT COUNTER STOPS, AFIN = 1 COUNTER STARTS, ARUN = 1 CPU WRITES SCIACTL WITH $30 RXD Figure 13-23. Bit Time Measurement with ACLK = 1, Scenario B MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 181 Enhanced Serial Communications Interface (ESCI) Module MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 182 Freescale Semiconductor Chapter 14 System Integration Module (SIM) 14.1 Introduction This section describes the system integration module (SIM). Together with the central processor unit (CPU), the SIM controls all microcontroller unit (MCU) activities. A block diagram of the SIM is shown in Figure 14-1. Table 14-1 is a summary of the SIM input/output (I/O) registers. The SIM is a system state controller that coordinates CPU and exception timing. The SIM is responsible for: * Bus clock generation and control for CPU and peripherals: - Stop/wait/reset/break entry and recovery - Internal clock control * Master reset control, including power-on reset (POR) and computer operating properly (COP) timeout * Interrupt arbitration Table 14-1 shows the internal signal names used in this section. Table 14-1. Signal Name Conventions Signal Name Description CGMXCLK Buffered version of OSC1 from clock generator module (CGM) CGMVCLK PLL output CGMOUT PLL-based or OSC1-based clock output from CGM module (Bus clock = CGMOUT divided by two) IAB IDB PORRST Internal address bus Internal data bus Signal from the power-on reset module to the SIM IRST Internal reset signal R/W Read/write signal MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 183 System Integration Module (SIM) MODULE STOP MODULE WAIT CPU STOP (FROM CPU) CPU WAIT (FROM CPU) STOP/WAIT CONTROL SIMOSCEN (TO CGM) SIM COUNTER CGMXCLK (FROM CGM) CGMOUT (FROM CGM) /2 CLOCK CONTROL VDD CLOCK GENERATORS INTERNAL PULLUP DEVICE RESET PIN LOGIC INTERNAL CLOCKS FORCED MONITOR MODE ENTRY LVI (FROM LVI MODULE) POR CONTROL MASTER RESET CONTROL RESET PIN CONTROL SIM RESET STATUS REGISTER ILLEGAL OPCODE (FROM CPU) ILLEGAL ADDRESS (FROM ADDRESS MAP DECODERS) COP (FROM COP MODULE) RESET INTERRUPT CONTROL AND PRIORITY DECODE INTERRUPT SOURCES CPU INTERFACE Figure 14-1. SIM Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 184 Freescale Semiconductor Introduction 7 Addr. Register Name $FE00 Read: Break Status Register (BSR) Write: See page 199. Reset: Bit 7 6 5 4 3 2 1 R R R R R R 0 0 0 0 0 0 0 0 SBSW Note(1) Bit 0 R 1. Writing a 0 clears SBSW. $FE01 $FE03 $FE04 $FE05 $FE06 $FE07 Read: SIM Reset Status Register (SRSR) Write: See page 199. POR: Read: Break Flag Control Register (BFCR) Write: See page 200. Reset: POR PIN COP ILOP ILAD MODRST LVI 0 1 0 0 0 0 0 0 0 BCFE R R R R R R R 0 Read: Interrupt Status Register 1 (INT1) Write: See page 195. Reset: IF6 IF5 IF4 IF3 IF2 IF1 0 0 R R R R R R R R 0 0 0 0 0 0 0 0 Read: Interrupt Status Register 2 (INT2) Write: See page 195. Reset: IF14 IF13 IF12 IF11 IF10 IF9 IF8 IF7 R R R R R R R R 0 0 0 0 0 0 0 0 Read: Interrupt Status Register 3 (INT3) Write: See page 195. Reset: IF22 IF32 IF20 IF19 IF18 IF17 IF16 IF15 R R R R R R R R 0 0 0 0 0 0 0 0 Read: Interrupt Status Register 4 (INT4) Write: See page 196. Reset: 0 0 0 0 0 0 IF24 IF23 R R R R R R R R 0 0 0 0 0 0 0 0 R = Reserved = Unimplemented Figure 14-2. SIM I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 185 System Integration Module (SIM) 14.2 SIM Bus Clock Control and Generation The bus clock generator provides system clock signals for the CPU and peripherals on the MCU. The system clocks are generated from an incoming clock, CGMOUT, as shown in Figure 14-3. This clock originates from either an external oscillator or from the on-chip PLL. 14.2.1 Bus Timing In user mode, the internal bus frequency is either the crystal oscillator output (CGMXCLK) divided by four or the PLL output (CGMVCLK) divided by four. 14.2.2 Clock Startup from POR or LVI Reset When the power-on reset module or the low-voltage inhibit module generates a reset, the clocks to the CPU and peripherals are inactive and held in an inactive phase until after the 4096 CGMXCLK cycle POR timeout has completed. The RST pin is driven low by the SIM during this entire period. The bus clocks start upon completion of the timeout. 14.2.3 Clocks in Stop Mode and Wait Mode Upon exit from stop mode by an interrupt or reset, the SIM allows CGMXCLK to clock the SIM counter. The CPU and peripheral clocks do not become active until after the stop delay timeout. This timeout is selectable as 4096 or 32 CGMXCLK cycles. See 14.6.2 Stop Mode. OSC2 OSCILLATOR (OSC) CGMXCLK OSC1 TO TBM,TIM1,TIM2, ADC, SIM OSCENINSTOP FROM CONFIG SIMOSCEN SIM COUNTER CGMRCLK /2 PHASE-LOCKED LOOP (PLL) IT12 TO REST OF CHIP BUS CLOCK GENERATORS IT23 TO REST OF CHIP Figure 14-3. System Clock Signals In wait mode, the CPU clocks are inactive. The SIM also produces two sets of clocks for other modules. Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 186 Freescale Semiconductor Reset and System Initialization 14.3 Reset and System Initialization The MCU has these reset sources: * Power-on reset module (POR) * External reset pin (RST) * Computer operating properly module (COP) * Low-voltage inhibit module (LVI) * Illegal opcode * Illegal address * Forced monitor mode entry reset (MODRST) All of these resets produce the vector $FFFE:$FFFF ($FEFE:$FEFF in monitor mode) and assert the internal reset signal (IRST). IRST causes all registers to be returned to their default values and all modules to be returned to their reset states. An internal reset clears the SIM counter (see 14.4 SIM Counter), but an external reset does not. Each of the resets sets a corresponding bit in the SIM reset status register (SRSR). See 14.7 SIM Registers. A reset immediately stops the operation of the instruction being executed. Reset initializes certain control and status bits. Reset selects CGMXCLK divided by four as the bus clock. 14.3.1 External Pin Reset The RST pin circuit includes an internal pullup device. Pulling the asynchronous RST pin low halts all processing. The PIN bit of the SIM reset status register (SRSR) is set as long as RST is held low for at least the minimum tRL time and no other reset sources are present. Figure 14-4 shows the relative timing. CGMOUT RST IAB VECT H PC VECT L Figure 14-4. External Reset Timing 14.3.2 Active Resets from Internal Sources All internal reset sources actively pull the RST pin low for 32 CGMXCLK cycles to allow resetting of external peripherals. The internal reset continues to be asserted for an additional 32 cycles at which point the reset vector will be fetched. See Figure 14-5. An internal reset can be caused by an illegal address, illegal opcode, COP timeout, LVI, or POR. See Figure 14-6. NOTE For LVI or POR resets, the SIM cycles through 4096 CGMXCLK cycles during which the SIM forces the RST pin low. The internal reset signal then follows the sequence from the falling edge of RST shown in Figure 14-5. The COP reset is asynchronous to the bus clock. The active reset feature allows the part to issue a reset to peripherals and other chips within a system built around the MCU. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 187 System Integration Module (SIM) RST PULLED LOW BY MCU RST 32 CYCLES 32 CYCLES CGMXCLK IAB VECTOR HIGH Figure 14-5. Internal Reset Timing ILLEGAL ADDRESS RST ILLEGAL OPCODE RST COPRST LVI POR MODRST INTERNAL RESET Figure 14-6. Sources of Internal Reset Table 14-2. Reset Recovery Reset Recovery Type Actual Number of Cycles POR/LVI 4163 (4096 + 64 + 3) All others 67 (64 + 3) 14.3.2.1 Power-On Reset When power is first applied to the MCU, the power-on reset module (POR) generates a pulse to indicate that power-on has occurred. The external reset pin (RST) is held low while the SIM counter counts out 4096 + 32 CGMXCLK cycles. Thirty-two CGMXCLK cycles later, the CPU and memories are released from reset to allow the reset vector sequence to occur. At power-on, these events occur: * A POR pulse is generated. * The internal reset signal is asserted. * The SIM enables CGMOUT. * Internal clocks to the CPU and modules are held inactive for 4096 CGMXCLK cycles to allow stabilization of the oscillator. * The RST pin is driven low during the oscillator stabilization time. * The POR bit of the SIM reset status register (SRSR) is set. 14.3.2.2 Computer Operating Properly (COP) Reset An input to the SIM is reserved for the COP reset signal. The overflow of the COP counter causes an internal reset and sets the COP bit in the SIM reset status register (SRSR) if the COPD bit in the CONFIG1 register is cleared. The SIM actively pulls down the RST pin for all internal reset sources. The COP module is disabled if the RST pin or the IRQ pin is held at VTST while the MCU is in monitor mode. During a break state, VTST on the RST pin disables the COP module. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 188 Freescale Semiconductor Reset and System Initialization OSC1 PORRST 4096 CYCLES 32 CYCLES 32 CYCLES CGMXCLK CGMOUT RST $FFFE IAB $FFFF Figure 14-7. POR Recovery 14.3.2.3 Illegal Opcode Reset The SIM decodes signals from the CPU to detect illegal instructions. An illegal instruction sets the ILOP bit in the SIM reset status register (SRSR) and causes a reset. If the stop enable bit, STOP, in the CONFIG1 register is 0, the SIM treats the STOP instruction as an illegal opcode and causes an illegal opcode reset. The SIM actively pulls down the RST pin for all internal reset sources. 14.3.2.4 Illegal Address Reset An opcode fetch from an unmapped address generates an illegal address reset. The SIM verifies that the CPU is fetching an opcode prior to asserting the ILAD bit in the SIM reset status register (SRSR) and resetting the MCU. A data fetch from an unmapped address does not generate a reset. The SIM actively pulls down the RST pin for all internal reset sources. 14.3.2.5 Low-Voltage Inhibit (LVI) Reset The low-voltage inhibit module (LVI) asserts its output to the SIM when the VDD voltage falls to the VTRIPF voltage. The LVI bit in the SIM reset status register (SRSR) is set, and the external reset pin (RST) is asserted if the LVIPWRD and LVIRSTD bits in the CONFIG1 register are 0. The RST pin will be held low while the SIM counter counts out 4096 + 32 CGMXCLK cycles after VDD rises above VTRIPR. Thirty-two CGMXCLK cycles later, the CPU is released from reset to allow the reset vector sequence to occur. The SIM actively pulls down the RST pin for all internal reset sources. 14.3.2.6 Monitor Mode Entry Module Reset (MODRST) The monitor mode entry module reset (MODRST) asserts its output to the SIM when monitor mode is entered in the condition where the reset vectors are erased ($FF) (see 19.3.1.1 Normal Monitor Mode). When MODRST gets asserted, an internal reset occurs. The SIM actively pulls down the RST pin for all internal reset sources. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 189 System Integration Module (SIM) 14.4 SIM Counter The SIM counter is used by the power-on reset module (POR) and in stop mode recovery to allow the oscillator time to stabilize before enabling the internal bus clocks. The SIM counter also serves as a prescaler for the computer operating properly (COP) module. The SIM counter overflow supplies the clock for the COP module. The SIM counter is 12 bits long. 14.4.1 SIM Counter During Power-On Reset The power-on reset module (POR) detects power applied to the MCU. At power-on, the POR circuit asserts the signal PORRST. Once the SIM is initialized, it enables the clock generation module (CGM) to drive the bus clock state machine. 14.4.2 SIM Counter During Stop Mode Recovery The SIM counter also is used for stop mode recovery. The STOP instruction clears the SIM counter. After an interrupt, break, or reset, the SIM senses the state of the short stop recovery bit, SSREC, in the CONFIG1 register. If the SSREC bit is a 1, then the stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles down to 32 CGMXCLK cycles. This is ideal for applications using crystals with the OSCENINSTOP bit set. External crystal applications should use the full stop recovery time, SSREC cleared, with the OSCENINSTOP bit cleared. See Chapter 5 Configuration Register (CONFIG). 14.4.3 SIM Counter and Reset States External reset has no effect on the SIM counter. See 14.6.2 Stop Mode for details. The SIM counter is free-running after all reset states. See 14.3.2 Active Resets from Internal Sources for counter control and internal reset recovery sequences. 14.5 Exception Control Normal, sequential program execution can be changed in three different ways: * Interrupts: - Maskable hardware CPU interrupts - Non-maskable software interrupt instruction (SWI) * Reset * Break interrupts 14.5.1 Interrupts At the beginning of an interrupt, the CPU saves the CPU register contents on the stack and sets the interrupt mask (I bit) to prevent additional interrupts. At the end of an interrupt, the RTI instruction recovers the CPU register contents from the stack so that normal processing can resume. Figure 14-8 shows interrupt entry timing. Figure 14-9 shows interrupt recovery timing. Interrupts are latched, and arbitration is performed in the SIM at the start of interrupt processing. The arbitration result is a constant that the CPU uses to determine which vector to fetch. Once an interrupt is latched by the SIM, no other interrupt can take precedence, regardless of priority, until the latched interrupt is serviced (or the I bit is cleared). See Figure 14-10. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 190 Freescale Semiconductor Exception Control 14.5.1.1 Hardware Interrupts A hardware interrupt does not stop the current instruction. Processing of a hardware interrupt begins after completion of the current instruction. When the current instruction is complete, the SIM checks all pending hardware interrupts. If interrupts are not masked (I bit clear in the condition code register) and if the corresponding interrupt enable bit is set, the SIM proceeds with interrupt processing; otherwise, the next instruction is fetched and executed. MODULE INTERRUPT I BIT IAB DUMMY IDB SP DUMMY SP - 1 SP - 2 PC - 1[7:0] PC - 1[15:8] SP - 3 X SP - 4 A VECT H CCR VECT L V DATA H START ADDR V DATA L OPCODE R/W Figure 14-8. Interrupt Entry Timing MODULE INTERRUPT I BIT IAB SP - 4 IDB SP - 3 CCR SP - 2 A SP - 1 X SP PC PC + 1 PC - 1 [7:0] PC - 1 [15:8] OPCODE OPERAND R/W Figure 14-9. Interrupt Recovery Timing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 191 System Integration Module (SIM) FROM RESET BREAK INTERRUPT ? NO YES YES BITSET? SET? IIBIT NO IRQ INTERRUPT ? NO YES CGM INTERRUPT ? NO YES OTHER INTERRUPTS ? YES NO STACK CPU REGISTERS SET I BIT LOAD PC WITH INTERRUPT VECTOR FETCH NEXT INSTRUCTION SWI INSTRUCTION ? YES NO RTI INSTRUCTION ? YES UNSTACK CPU REGISTERS NO EXECUTE INSTRUCTION Figure 14-10. Interrupt Processing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 192 Freescale Semiconductor Exception Control If more than one interrupt is pending at the end of an instruction execution, the highest priority interrupt is serviced first. Figure 14-11 demonstrates what happens when two interrupts are pending. If an interrupt is pending upon exit from the original interrupt service routine, the pending interrupt is serviced before the LDA instruction is executed. CLI LDA #$FF INT1 BACKGROUND ROUTINE PSHH INT1 INTERRUPT SERVICE ROUTINE PULH RTI INT2 PSHH INT2 INTERRUPT SERVICE ROUTINE PULH RTI Figure 14-11. Interrupt Recognition Example The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions. However, in the case of the INT1 RTI prefetch, this is a redundant operation. NOTE To maintain compatibility with the M6805 Family, the H register is not pushed on the stack during interrupt entry. If the interrupt service routine modifies the H register or uses the indexed addressing mode, software should save the H register and then restore it prior to exiting the routine. 14.5.1.2 SWI Instruction The SWI instruction is a non-maskable instruction that causes an interrupt regardless of the state of the interrupt mask (I bit) in the condition code register. NOTE A software interrupt pushes PC onto the stack. A software interrupt does not push PC - 1, as a hardware interrupt does. 14.5.1.3 Interrupt Status Registers The flags in the interrupt status registers identify maskable interrupt sources. Table 14-3 summarizes the interrupt sources, hardware flag bits, hardware interrupt mask bits, interrupt status register flags, interrupt priority, and exception vectors. The interrupt status registers can be useful for debugging. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 193 System Integration Module (SIM) Table 14-3. Interrupt Sources Flag Mask(1) INT Register Flag Priority(2) Vector Address Reset None None None 0 $FFFE-$FFFF SWI instruction None None None 0 $FFFC-$FFFD IRQ pin IRQF IMASK1 IF1 1 $FFFA-$FFFB CGM change in lock PLLF PLLIE IF2 2 $FFF8-$FFF9 TIM1 channel 0 CH0F CH0IE IF3 3 $FFF6-$FFF7 TIM1 channel 1 CH1F CH1IE IF4 4 $FFF4-$FFF5 TOF TOIE IF5 5 $FFF2-$FFF3 TIM2 channel 0 CH0F CH0IE IF6 6 $FFF0-$FFF1 TIM2 channel 1 CH1F CH1IE IF7 7 $FFEE-$FFEF TOF TOIE IF8 8 $FFEC-$FFED SPI receiver full SPRF SPRIE SPI overflow OVRF ERRIE IF9 9 $FFEA-$FFEB SPI mode fault MODF ERRIE SPI transmitter empty SPTE SPTIE IF10 10 $FFE8-$FFE9 SCI receiver overrun OR ORIE SCI noise flag NF NEIE IF11 11 $FFE6-$FFE7 SCI framing error FE FEIE SCI parity error PE PEIE SCI receiver full SCRF SCRIE IF12 12 $FFE4-$FFE5 SCI input idle IDLE ILIE SCI transmitter empty SCTE SCTIE IF13 13 $FFE2-$FFE3 TC TCIE Keyboard pin KEYF IMASKK IF14 14 $FFE0-$FFE1 ADC conversion complete COCO AIEN IF15 15 $FFDE-$FFDF Timebase TBIF TBIE IF16 16 $FFDC-$FFDD TIM2 channel 2 CH2F CH2IE IF21 21 $FFD2-FFD3 TIM2 channel 3 CH3F CH3IE IF22 22 $FFD0-FFD1 TIM2 channel 4 CH4F CH4IE IF23 23 $FFCE-FFCF TIM2 channel 5 CH5F CH5IE IF24 24 $FFCC-FFCD Source TIM1 overflow TIM2 overflow SCI transmission complete 1. The I bit in the condition code register is a global mask for all interrupt sources except the SWI instruction. 2. 0 = highest priority MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 194 Freescale Semiconductor Exception Control Interrupt Status Register 1 Address: $FE04 Bit 7 6 5 4 3 2 1 Bit 0 Read: IF6 IF5 IF4 IF3 IF2 IF1 0 0 Write: R R R R R R R R Reset: 0 0 0 0 0 0 0 0 R = Reserved Figure 14-12. Interrupt Status Register 1 (INT1) IF6-IF1 -- Interrupt Flags 1-6 These flags indicate the presence of interrupt requests from the sources shown in Table 14-3. 1 = Interrupt request present 0 = No interrupt request present Bit 0 and Bit 1 -- Always read 0 Interrupt Status Register 2 Address: $FE05 Bit 7 6 5 4 3 2 1 Bit 0 Read: IF14 IF13 IF12 IF11 IF10 IF9 IF8 IF7 Write: R R R R R R R R 0 0 0 0 0 0 0 0 R = Reserved Reset: Figure 14-13. Interrupt Status Register 2 (INT2) IF14-IF7 -- Interrupt Flags 14-7 These flags indicate the presence of interrupt requests from the sources shown in Table 14-3. 1 = Interrupt request present 0 = No interrupt request present Interrupt Status Register 3 Address: $FE06 Bit 7 6 5 4 3 2 1 Bit 0 Read: IF22 IF21 IF20 IF19 IF18 IF17 IF16 IF15 Write: R R R R R R R R Reset: 0 0 0 0 0 0 0 0 R = Reserved Figure 14-14. Interrupt Status Register 3 (INT3) IF22-IF15 -- Interrupt Flags 22-15 These flags indicate the presence of an interrupt request from the source shown in Table 14-3. 1 = Interrupt request present 0 = No interrupt request present MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 195 System Integration Module (SIM) Interrupt Status Register 4 Address: $FE07 Bit 7 6 5 4 3 2 1 Bit 0 Read: 0 0 0 0 0 0 IF24 IF23 Write: R R R R R R R R Reset: 0 0 0 0 0 0 0 0 R = Reserved Figure 14-15. Interrupt Status Register 4 (INT4) Bits 7-2 -- Always read 0 IF24-IF23 -- Interrupt Flags 24-23 These flags indicate the presence of an interrupt request from the source shown in Table 14-3. 1 = Interrupt request present 0 = No interrupt request present 14.5.2 Reset All reset sources always have equal and highest priority and cannot be arbitrated. 14.5.3 Break Interrupts The break module can stop normal program flow at a software-programmable break point by asserting its break interrupt output (see Chapter 17 Timer Interface Module (TIM1) and Chapter 18 Timer Interface Module (TIM2)). The SIM puts the CPU into the break state by forcing it to the SWI vector location. Refer to the break interrupt subsection of each module to see how each module is affected by the break state. 14.5.4 Status Flag Protection in Break Mode The SIM controls whether status flags contained in other modules can be cleared during break mode. The user can select whether flags are protected from being cleared by properly initializing the break clear flag enable bit (BCFE) in the SIM break flag control register (BFCR). Protecting flags in break mode ensures that set flags will not be cleared while in break mode. This protection allows registers to be freely read and written during break mode without losing status flag information. Setting the BCFE bit enables the clearing mechanisms. Once cleared in break mode, a flag remains cleared even when break mode is exited. Status flags with a 2-step clearing mechanism -- for example, a read of one register followed by the read or write of another -- are protected, even when the first step is accomplished prior to entering break mode. Upon leaving break mode, execution of the second step will clear the flag as normal. 14.6 Low-Power Modes Executing the WAIT or STOP instruction puts the MCU in a low power-consumption mode for standby situations. The SIM holds the CPU in a non-clocked state. The operation of each of these modes is described in the following subsections. Both STOP and WAIT clear the interrupt mask (I) in the condition code register, allowing interrupts to occur. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 196 Freescale Semiconductor Low-Power Modes 14.6.1 Wait Mode In wait mode, the CPU clocks are inactive while the peripheral clocks continue to run. Figure 14-16 shows the timing for wait mode entry. A module that is active during wait mode can wakeup the CPU with an interrupt if the interrupt is enabled. Stacking for the interrupt begins one cycle after the WAIT instruction during which the interrupt occurred. In wait mode, the CPU clocks are inactive. Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode. Wait mode also can be exited by a reset or break. A break interrupt during wait mode sets the SIM break stop/wait bit, SBSW, in the SIM break status register (BSR). If the COP disable bit, COPD, in the CONFIG1 register is 0, then the computer operating properly module (COP) is enabled and remains active in wait mode. IAB WAIT ADDR IDB WAIT ADDR + 1 PREVIOUS DATA SAME SAME NEXT OPCODE SAME SAME R/W Note: Previous data can be operand data or the WAIT opcode, depending on the last instruction. Figure 14-16. Wait Mode Entry Timing Figure 14-17 and Figure 14-18 show the timing for WAIT recovery. IAB $6E0B $A6 IDB $A6 $6E0C $A6 $01 $00FF $0B $00FE $00FD $00FC $6E EXITSTOPWAIT Note: EXITSTOPWAIT = RST pin, CPU interrupt, or break interrupt Figure 14-17. Wait Recovery from Interrupt or Break 32 CYCLES IAB IDB $6E0B $A6 $A6 32 CYCLES RSTVCTH RST VCTL $A6 RST CGMXCLK Figure 14-18. Wait Recovery from Internal Reset MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 197 System Integration Module (SIM) 14.6.2 Stop Mode In stop mode, the SIM counter is reset and the system clocks are disabled. An interrupt request from a module can cause an exit from stop mode. Stacking for interrupts begins after the selected stop recovery time has elapsed. Reset also causes an exit from stop mode. The SIM disables the clock generator module outputs (CGMOUT and CGMXCLK) in stop mode, stopping the CPU and peripherals. Stop recovery time is selectable using the SSREC bit in CONFIG1. If SSREC is set, stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles down to 32. This is ideal for applications using canned oscillators that do not require long startup times from stop mode. NOTE External crystal applications should use the full stop recovery time by clearing the SSREC bit unless OSCENINSTOP bit is set in CONFIG2. The SIM counter is held in reset from the execution of the STOP instruction until the beginning of stop recovery. It is then used to time the recovery period. Figure 14-19 shows stop mode entry timing. Figure 14-20 shows stop mode recovery time from interrupt. NOTE To minimize stop current, all pins configured as inputs should be driven to a 1 or 0. CPUSTOP IAB IDB STOP ADDR STOP ADDR + 1 PREVIOUS DATA SAME SAME NEXT OPCODE SAME SAME R/W Note: Previous data can be operand data or the STOP opcode, depending on the last instruction. Figure 14-19. Stop Mode Entry Timing STOP RECOVERY PERIOD CGMXCLK INT/BREAK IAB STOP +1 STOP + 2 STOP + 2 SP SP - 1 SP - 2 SP - 3 Figure 14-20. Stop Mode Recovery from Interrupt MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 198 Freescale Semiconductor SIM Registers 14.7 SIM Registers The SIM has three memory-mapped registers. Table 14-4 shows the mapping of these registers. Table 14-4. SIM Registers Address Register Access Mode $FE00 BSR User $FE01 SRSR User $FE03 BFCR User 14.7.1 Break Status Register The break status register (BSR) contains a flag to indicate that a break caused an exit from wait mode. This register is only used in emulation mode. Address: Read: Write: Reset: $FE00 Bit 7 6 5 4 3 2 R R R R R R 0 0 0 0 0 0 R = Reserved 1 SBSW Note(1) 0 Bit 0 R 0 1. Writing a 0 clears SBSW. Figure 14-21. Break Status Register (BSR) SBSW -- SIM Break Stop/Wait SBSW can be read within the break state SWI routine. The user can modify the return address on the stack by subtracting one from it. 1 = Wait mode was exited by break interrupt. 0 = Wait mode was not exited by break interrupt. 14.7.2 SIM Reset Status Register This register contains six flags that show the source of the last reset provided all previous reset status bits have been cleared. Clear the SIM reset status register by reading it. A power-on reset sets the POR bit and clears all other bits in the register. The register is initialized on power up with the POR bit set and all other bits cleared. During a POR or any other internal reset, the RST pin is pulled low. After the pin is released, it will be sampled 32 CGMXCLK cycles later. If the pin is not above VIH at this time, then the PIN bit may be set, in addition to whatever other bits are set. Address: Read: $FE01 Bit 7 6 5 4 3 2 1 Bit 0 POR PIN COP ILOP ILAD MODRST LVI 0 1 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 14-22. SIM Reset Status Register (SRSR) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 199 System Integration Module (SIM) POR -- Power-On Reset Bit 1 = Last reset caused by POR circuit 0 = Read of SRSR PIN -- External Reset Bit 1 = Last reset caused by external reset pin (RST) 0 = POR or read of SRSR COP -- Computer Operating Properly Reset Bit 1 = Last reset caused by COP counter 0 = POR or read of SRSR ILOP -- Illegal Opcode Reset Bit 1 = Last reset caused by an illegal opcode 0 = POR or read of SRSR ILAD -- Illegal Address Reset Bit (opcode fetches only) 1 = Last reset caused by an opcode fetch from an illegal address 0 = POR or read of SRSR MODRST -- Monitor Mode Entry Module Reset Bit 1 = Last reset caused by monitor mode entry when vector locations $FFFE and $FFFF are $FF after POR while IRQ = VDD 0 = POR or read of SRSR LVI -- Low-Voltage Inhibit Reset Bit 1 = Last reset caused by the LVI circuit 0 = POR or read of SRSR 14.7.3 Break Flag Control Register The break flag control register contains a bit that enables software to clear status bits while the MCU is in a break state. Address: Read: Write: Reset: $FE03 Bit 7 6 5 4 3 2 1 Bit 0 BCFE R R R R R R R 0 R = Reserved Figure 14-23. Break Flag Control Register (BFCR) BCFE -- Break Clear Flag Enable Bit This read/write bit enables software to clear status bits by accessing status registers while the MCU is in a break state. To clear status bits during the break state, the BCFE bit must be set. 1 = Status bits clearable during break 0 = Status bits not clearable during break MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 200 Freescale Semiconductor Chapter 15 Serial Peripheral Interface (SPI) Module 15.1 Introduction This section describes the serial peripheral interface (SPI) module, which allows full-duplex, synchronous, serial communications with peripheral devices. The text that follows describes the SPI. The SPI I/O pin names are SS (slave select), SPSCK (SPI serial clock), MOSI (master out slave in), and MISO (master in/slave out). The SPI shares four I/O pins with four parallel I/O ports. 15.2 Features Features of the SPI module include: * Full-duplex operation * Master and slave modes * Double-buffered operation with separate transmit and receive registers * Four master mode frequencies (maximum = bus frequency / 2) * Maximum slave mode frequency = bus frequency * Serial clock with programmable polarity and phase * Two separately enabled interrupts: - SPRF (SPI receiver full) - SPTE (SPI transmitter empty) * Mode fault error flag with CPU interrupt capability * Overflow error flag with CPU interrupt capability * Programmable wired-OR mode * I/O (input/output) port bit(s) software configurable with pullup device(s) if configured as input port bit(s) 15.3 Functional Description The SPI module allows full-duplex, synchronous, serial communication between the MCU and peripheral devices, including other MCUs. Software can poll the SPI status flags or SPI operation can be interrupt driven. If a port bit is configured for input, then an internal pullup device may be enabled for that port bit. The following paragraphs describe the operation of the SPI module. Refer to Figure 15-3 for a summary of the SPI I/O registers. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 201 Serial Peripheral Interface (SPI) Module INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 15-1. Block Diagram Highlighting SPI Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 202 Freescale Semiconductor Functional Description INTERNAL BUS TRANSMIT DATA REGISTER SHIFT REGISTER BUSCLK 7 6 5 4 3 2 1 MISO 0 /2 MOSI /8 CLOCK DIVIDER RECEIVE DATA REGISTER / 32 PIN CONTROL LOGIC / 128 SPMSTR SPE CLOCK SELECT SPR1 SPSCK M CLOCK LOGIC S SS SPR0 SPMSTR CPHA MODFEN TRANSMITTER CPU INTERRUPT REQUEST CPOL SPWOM ERRIE SPI CONTROL SPTIE RECEIVER/ERROR CPU INTERRUPT REQUEST SPRIE SPE SPRF SPTE OVRF MODF Figure 15-2. SPI Module Block Diagram Addr. Register Name $0010 SPI Control Register Read: (SPCR) Write: See page 217. Reset: $0011 SPI Status and Control Read: Register (SPSCR) Write: See page 218. Reset: $0012 SPI Data Register Read: (SPDR) Write: See page 220. Reset: Bit 7 6 5 4 3 2 1 Bit 0 SPRIE R SPMSTR CPOL CPHA SPWOM SPE SPTIE 0 0 0 0 0 MODFEN SPR1 SPR0 SPRF ERRIE 1 0 1 OVRF MODF SPTE 0 0 0 0 1 0 0 0 R7 R6 R5 R4 R3 R2 R1 R0 T7 T6 T5 T4 T3 T2 T1 T0 R = Reserved Unaffected by reset = Unimplemented Figure 15-3. SPI I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 203 Serial Peripheral Interface (SPI) Module 15.3.1 Master Mode The SPI operates in master mode when the SPI master bit, SPMSTR, is set. NOTE In a multi-SPI system, configure the SPI modules as master or slave before enabling them. Enable the master SPI before enabling the slave SPI. Disable the slave SPI before disabling the master SPI. See 15.12.1 SPI Control Register. Only a master SPI module can initiate transmissions. Software begins the transmission from a master SPI module by writing to the transmit data register. If the shift register is empty, the byte immediately transfers to the shift register, setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the MOSI pin under the control of the serial clock. See Figure 15-4. MASTER MCU SHIFT REGISTER SLAVE MCU MISO MISO MOSI MOSI SPSCK BAUD RATE GENERATOR SS SHIFT REGISTER SPSCK VDD SS Figure 15-4. Full-Duplex Master-Slave Connections The SPR1 and SPR0 bits control the baud rate generator and determine the speed of the shift register. (See 15.12.2 SPI Status and Control Register.) Through the SPSCK pin, the baud rate generator of the master also controls the shift register of the slave peripheral. As the byte shifts out on the MOSI pin of the master, another byte shifts in from the slave on the master's MISO pin. The transmission ends when the receiver full bit, SPRF, becomes set. At the same time that SPRF becomes set, the byte from the slave transfers to the receive data register. In normal operation, SPRF signals the end of a transmission. Software clears SPRF by reading the SPI status and control register with SPRF set and then reading the SPI data register. Writing to the SPI data register (SPDR) clears SPTE. 15.3.2 Slave Mode The SPI operates in slave mode when SPMSTR is clear. In slave mode, the SPSCK pin is the input for the serial clock from the master MCU. Before a data transmission occurs, the SS pin of the slave SPI must be low. SS must remain low until the transmission is complete. See 15.6.2 Mode Fault Error. In a slave SPI module, data enters the shift register under the control of the serial clock from the master SPI module. After a byte enters the shift register of a slave SPI, it transfers to the receive data register, and the SPRF bit is set. To prevent an overflow condition, slave software then must read the receive data register before another full byte enters the shift register. The maximum frequency of the SPSCK for an SPI configured as a slave is the bus clock speed (which is twice as fast as the fastest master SPSCK clock that can be generated). The frequency of the SPSCK for MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 204 Freescale Semiconductor Transmission Formats an SPI configured as a slave does not have to correspond to any SPI baud rate. The baud rate only controls the speed of the SPSCK generated by an SPI configured as a master. Therefore, the frequency of the SPSCK for an SPI configured as a slave can be any frequency less than or equal to the bus speed. When the master SPI starts a transmission, the data in the slave shift register begins shifting out on the MISO pin. The slave can load its shift register with a new byte for the next transmission by writing to its transmit data register. The slave must write to its transmit data register at least one bus cycle before the master starts the next transmission. Otherwise, the byte already in the slave shift register shifts out on the MISO pin. Data written to the slave shift register during a transmission remains in a buffer until the end of the transmission. When the clock phase bit (CPHA) is set, the first edge of SPSCK starts a transmission. When CPHA is clear, the falling edge of SS starts a transmission. See 15.4 Transmission Formats. NOTE SPSCK must be in the proper idle state before the slave is enabled to prevent SPSCK from appearing as a clock edge. 15.4 Transmission Formats During an SPI transmission, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). A serial clock synchronizes shifting and sampling on the two serial data lines. A slave select line allows selection of an individual slave SPI device; slave devices that are not selected do not interfere with SPI bus activities. On a master SPI device, the slave select line can optionally be used to indicate multiple-master bus contention. 15.4.1 Clock Phase and Polarity Controls Software can select any of four combinations of serial clock (SPSCK) phase and polarity using two bits in the SPI control register (SPCR). The clock polarity is specified by the CPOL control bit, which selects an active high or low clock and has no significant effect on the transmission format. The clock phase (CPHA) control bit selects one of two fundamentally different transmission formats. The clock phase and polarity should be identical for the master SPI device and the communicating slave device. In some cases, the phase and polarity are changed between transmissions to allow a master device to communicate with peripheral slaves having different requirements. NOTE Before writing to the CPOL bit or the CPHA bit, disable the SPI by clearing the SPI enable bit (SPE). 15.4.2 Transmission Format When CPHA = 0 Figure 15-5 shows an SPI transmission in which CPHA = 0. The figure should not be used as a replacement for data sheet parametric information. Two waveforms are shown for SPSCK: one for CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing diagram since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave in (MOSI) pins are directly connected between the master and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The slave SPI drives its MISO output only when its slave select input (SS) is low, so that only the selected slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS pin of the master must be high or must be reconfigured as MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 205 Serial Peripheral Interface (SPI) Module general-purpose I/O not affecting the SPI. (See 15.6.2 Mode Fault Error.) When CPHA = 0, the first SPSCK edge is the MSB capture strobe. Therefore, the slave must begin driving its data before the first SPSCK edge, and a falling edge on the SS pin is used to start the slave data transmission. The slave's SS pin must be toggled back to high and then low again between each byte transmitted as shown in Figure 15-6. When CPHA = 0 for a slave, the falling edge of SS indicates the beginning of the transmission. This causes the SPI to leave its idle state and begin driving the MISO pin with the MSB of its data. Once the transmission begins, no new data is allowed into the shift register from the transmit data register. Therefore, the SPI data register of the slave must be loaded with transmit data before the falling edge of SS. Any data written after the falling edge is stored in the transmit data register and transferred to the shift register after the current transmission. SPSCK CYCLE # FOR REFERENCE 1 2 3 4 5 6 7 8 MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB SPSCK; CPOL = 0 SPSCK; CPOL =1 MOSI FROM MASTER MISO FROM SLAVE MSB SS; TO SLAVE CAPTURE STROBE Figure 15-5. Transmission Format (CPHA = 0) MISO/MOSI BYTE 1 BYTE 2 BYTE 3 MASTER SS SLAVE SS CPHA = 0 SLAVE SS CPHA = 1 Figure 15-6. CPHA/SS Timing 15.4.3 Transmission Format When CPHA = 1 Figure 15-7 shows an SPI transmission in which CPHA = 1. The figure should not be used as a replacement for data sheet parametric information. Two waveforms are shown for SPSCK: one for CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing diagram since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave in (MOSI) pins are directly connected between the master and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The slave SPI drives its MISO output only when its slave select input (SS) is low, so that only the selected slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS pin of the master must be high or must be reconfigured as general-purpose I/O not affecting the SPI. (See 15.6.2 Mode Fault Error.) When CPHA = 1, the master begins driving its MOSI pin on the first SPSCK MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 206 Freescale Semiconductor Transmission Formats edge. Therefore, the slave uses the first SPSCK edge as a start transmission signal. The SS pin can remain low between transmissions. This format may be preferable in systems having only one master and only one slave driving the MISO data line. SPSCK CYCLE # FOR REFERENCE 1 2 3 4 5 6 7 8 MOSI FROM MASTER MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB MISO FROM SLAVE MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 SPSCK; CPOL = 0 SPSCK; CPOL =1 LSB SS; TO SLAVE CAPTURE STROBE Figure 15-7. Transmission Format (CPHA = 1) When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning of the transmission. This causes the SPI to leave its idle state and begin driving the MISO pin with the MSB of its data. Once the transmission begins, no new data is allowed into the shift register from the transmit data register. Therefore, the SPI data register of the slave must be loaded with transmit data before the first edge of SPSCK. Any data written after the first edge is stored in the transmit data register and transferred to the shift register after the current transmission. 15.4.4 Transmission Initiation Latency When the SPI is configured as a master (SPMSTR = 1), writing to the SPDR starts a transmission. CPHA has no effect on the delay to the start of the transmission, but it does affect the initial state of the SPSCK signal. When CPHA = 0, the SPSCK signal remains inactive for the first half of the first SPSCK cycle. When CPHA = 1, the first SPSCK cycle begins with an edge on the SPSCK line from its inactive to its active level. The SPI clock rate (selected by SPR1:SPR0) affects the delay from the write to SPDR and the start of the SPI transmission. (See Figure 15-8.) The internal SPI clock in the master is a free-running derivative of the internal MCU clock. To conserve power, it is enabled only when both the SPE and SPMSTR bits are set. Since the SPI clock is free-running, it is uncertain where the write to the SPDR occurs relative to the slower SPSCK. This uncertainty causes the variation in the initiation delay shown in Figure 15-8. This delay is no longer than a single SPI bit time. That is, the maximum delay is two MCU bus cycles for DIV2, eight MCU bus cycles for DIV8, 32 MCU bus cycles for DIV32, and 128 MCU bus cycles for DIV128. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 207 Serial Peripheral Interface (SPI) Module WRITE TO SPDR INITIATION DELAY BUS CLOCK MOSI MSB BIT 5 BIT 6 SPSCK CPHA = 1 SPSCK CPHA = 0 SPSCK CYCLE NUMBER 1 3 2 INITIATION DELAY FROM WRITE SPDR TO TRANSFER BEGIN WRITE TO SPDR BUS CLOCK EARLIEST BUS CLOCK WRITE TO SPDR EARLIEST BUS CLOCK WRITE TO SPDR EARLIEST BUS CLOCK WRITE TO SPDR EARLIEST LATEST SPSCK = BUS CLOCK / 2; 2 POSSIBLE START POINTS SPSCK = BUS CLOCK / 8; 8 POSSIBLE START POINTS LATEST SPSCK = BUS CLOCK / 32; 32 POSSIBLE START POINTS LATEST SPSCK = BUS CLOCK / 128; 128 POSSIBLE START POINTS LATEST Figure 15-8. Transmission Start Delay (Master) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 208 Freescale Semiconductor Queuing Transmission Data 15.5 Queuing Transmission Data The double-buffered transmit data register allows a data byte to be queued and transmitted. For an SPI configured as a master, a queued data byte is transmitted immediately after the previous transmission has completed. The SPI transmitter empty flag (SPTE) indicates when the transmit data buffer is ready to accept new data. Write to the transmit data register only when SPTE is high. Figure 15-9 shows the timing associated with doing back-to-back transmissions with the SPI (SPSCK has CPHA: CPOL = 1:0). WRITE TO SPDR SPTE 1 3 2 8 5 10 SPSCK CPHA:CPOL = 1:0 MOSI MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT 6 5 4 6 5 4 3 2 1 6 5 4 3 2 1 BYTE 1 BYTE 2 BYTE 3 4 SPRF 9 6 READ SPSCR 11 7 READ SPDR 12 1 CPU WRITES BYTE 1 TO SPDR, CLEARING SPTE BIT. 7 CPU READS SPDR, CLEARING SPRF BIT. 2 BYTE 1 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. 8 CPU WRITES BYTE 3 TO SPDR, QUEUEING BYTE 3 AND CLEARING SPTE BIT. 9 SECOND INCOMING BYTE TRANSFERS FROM SHIFT REGISTER TO RECEIVE DATA REGISTER, SETTING SPRF BIT. 10 BYTE 3 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. 11 CPU READS SPSCR WITH SPRF BIT SET. 3 CPU WRITES BYTE 2 TO SPDR, QUEUEING BYTE 2 AND CLEARING SPTE BIT. FIRST INCOMING BYTE TRANSFERS FROM SHIFT REGISTER TO RECEIVE DATA REGISTER, SETTING SPRF BIT. 5 BYTE 2 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. 6 CPU READS SPSCR WITH SPRF BIT SET. 4 12 CPU READS SPDR, CLEARING SPRF BIT. Figure 15-9. SPRF/SPTE CPU Interrupt Timing The transmit data buffer allows back-to-back transmissions without the slave precisely timing its writes between transmissions as in a system with a single data buffer. Also, if no new data is written to the data buffer, the last value contained in the shift register is the next data word to be transmitted. For an idle master or idle slave that has no data loaded into its transmit buffer, the SPTE is set again no more than two bus cycles after the transmit buffer empties into the shift register. This allows the user to queue up a 16-bit value to send. For an already active slave, the load of the shift register cannot occur until the transmission is completed. This implies that a back-to-back write to the transmit data register is not possible. SPTE indicates when the next write can occur. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 209 Serial Peripheral Interface (SPI) Module 15.6 Error Conditions The following flags signal SPI error conditions: * Overflow (OVRF) -- Failing to read the SPI data register before the next full byte enters the shift register sets the OVRF bit. The new byte does not transfer to the receive data register, and the unread byte still can be read. OVRF is in the SPI status and control register. * Mode fault error (MODF) -- The MODF bit indicates that the voltage on the slave select pin (SS) is inconsistent with the mode of the SPI. MODF is in the SPI status and control register. 15.6.1 Overflow Error The overflow flag (OVRF) becomes set if the receive data register still has unread data from a previous transmission when the capture strobe of bit 1 of the next transmission occurs. The bit 1 capture strobe occurs in the middle of SPSCK cycle 7 (see Figure 15-5 and Figure 15-7.) If an overflow occurs, all data received after the overflow and before the OVRF bit is cleared does not transfer to the receive data register and does not set the SPI receiver full bit (SPRF). The unread data that transferred to the receive data register before the overflow occurred can still be read. Therefore, an overflow error always indicates the loss of data. Clear the overflow flag by reading the SPI status and control register and then reading the SPI data register. OVRF generates a receiver/error CPU interrupt request if the error interrupt enable bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same CPU interrupt vector (see Figure 15-12.) It is not possible to enable MODF or OVRF individually to generate a receiver/error CPU interrupt request. However, leaving MODFEN low prevents MODF from being set. If the CPU SPRF interrupt is enabled and the OVRF interrupt is not, watch for an overflow condition. Figure 15-10 shows how it is possible to miss an overflow. The first part of Figure 15-10 shows how it is possible to read the SPSCR and SPDR to clear the SPRF without problems. However, as illustrated by the second transmission example, the OVRF bit can be set in between the time that SPSCR and SPDR are read. In this case, an overflow can be missed easily. Since no more SPRF interrupts can be generated until this OVRF is serviced, it is not obvious that bytes are being lost as more transmissions are completed. To prevent this, either enable the OVRF interrupt or do another read of the SPSCR following the read of the SPDR. This ensures that the OVRF was not set before the SPRF was cleared and that future transmissions can set the SPRF bit. Figure 15-11 illustrates this process. Generally, to avoid this second SPSCR read, enable the OVRF to the CPU by setting the ERRIE bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 210 Freescale Semiconductor Error Conditions BYTE 1 BYTE 2 BYTE 3 BYTE 4 1 4 6 8 SPRF OVRF READ SPSCR 2 5 READ SPDR 3 7 1 BYTE 1 SETS SPRF BIT. 2 CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. CPU READS BYTE 1 IN SPDR, CLEARING SPRF BIT. BYTE 2 SETS SPRF BIT. 3 4 5 CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. 6 BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST. 7 CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT, BUT NOT OVRF BIT. 8 BYTE 4 FAILS TO SET SPRF BIT BECAUSE OVRF BIT IS NOT CLEARED. BYTE 4 IS LOST. Figure 15-10. Missed Read of Overflow Condition BYTE 1 SPI RECEIVE COMPLETE BYTE 2 5 1 BYTE 3 7 BYTE 4 11 SPRF OVRF READ SPSCR 2 READ SPDR 4 3 1 BYTE 1 SETS SPRF BIT. 2 CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. CPU READS BYTE 1 IN SPDR, CLEARING SPRF BIT. 3 6 9 8 12 10 14 13 8 CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT. 9 CPU READS SPSCR AGAIN TO CHECK OVRF BIT. 10 CPU READS BYTE 2 SPDR, CLEARING OVRF BIT. 4 CPU READS SPSCR AGAIN TO CHECK OVRF BIT. 5 BYTE 2 SETS SPRF BIT. 12 CPU READS SPSCR. 6 CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. 13 CPU READS BYTE 4 IN SPDR, CLEARING SPRF BIT. 7 BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST. 14 CPU READS SPSCR AGAIN TO CHECK OVRF BIT. 11 BYTE 4 SETS SPRF BIT. Figure 15-11. Clearing SPRF When OVRF Interrupt Is Not Enabled MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 211 Serial Peripheral Interface (SPI) Module 15.6.2 Mode Fault Error Setting SPMSTR selects master mode and configures the SPSCK and MOSI pins as outputs and the MISO pin as an input. Clearing SPMSTR selects slave mode and configures the SPSCK and MOSI pins as inputs and the MISO pin as an output. The mode fault bit, MODF, becomes set any time the state of the slave select pin, SS, is inconsistent with the mode selected by SPMSTR. To prevent SPI pin contention and damage to the MCU, a mode fault error occurs if: * The SS pin of a slave SPI goes high during a transmission * The SS pin of a master SPI goes low at any time For the MODF flag to be set, the mode fault error enable bit (MODFEN) must be set. Clearing the MODFEN bit does not clear the MODF flag but does prevent MODF from being set again after MODF is cleared. MODF generates a receiver/error CPU interrupt request if the error interrupt enable bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same CPU interrupt vector. (See Figure 15-12.) It is not possible to enable MODF or OVRF individually to generate a receiver/error CPU interrupt request. However, leaving MODFEN low prevents MODF from being set. In a master SPI with the mode fault enable bit (MODFEN) set, the mode fault flag (MODF) is set if SS goes low. A mode fault in a master SPI causes the following events to occur: * If ERRIE = 1, the SPI generates an SPI receiver/error CPU interrupt request. * The SPE bit is cleared. * The SPTE bit is set. * The SPI state counter is cleared. * The data direction register of the shared I/O port regains control of port drivers. NOTE To prevent bus contention with another master SPI after a mode fault error, clear all SPI bits of the data direction register of the shared I/O port before enabling the SPI. When configured as a slave (SPMSTR = 0), the MODF flag is set if SS goes high during a transmission. When CPHA = 0, a transmission begins when SS goes low and ends once the incoming SPSCK goes back to its idle level following the shift of the eighth data bit. When CPHA = 1, the transmission begins when the SPSCK leaves its idle level and SS is already low. The transmission continues until the SPSCK returns to its idle level following the shift of the last data bit. See 15.4 Transmission Formats. NOTE Setting the MODF flag does not clear the SPMSTR bit. SPMSTR has no function when SPE = 0. Reading SPMSTR when MODF = 1 shows the difference between a MODF occurring when the SPI is a master and when it is a slave. NOTE When CPHA = 0, a MODF occurs if a slave is selected (SS is low) and later unselected (SS is high) even if no SPSCK is sent to that slave. This happens because SS low indicates the start of the transmission (MISO driven out with the value of MSB) for CPHA = 0. When CPHA = 1, a slave can be selected and then later unselected with no transmission occurring. Therefore, MODF does not occur since a transmission was never begun. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 212 Freescale Semiconductor Interrupts In a slave SPI (MSTR = 0), MODF generates an SPI receiver/error CPU interrupt request if the ERRIE bit is set. The MODF bit does not clear the SPE bit or reset the SPI in any way. Software can abort the SPI transmission by clearing the SPE bit of the slave. NOTE A high on the SS pin of a slave SPI puts the MISO pin in a high impedance state. Also, the slave SPI ignores all incoming SPSCK clocks, even if it was already in the middle of a transmission. To clear the MODF flag, read the SPSCR with the MODF bit set and then write to the SPCR register. This entire clearing mechanism must occur with no MODF condition existing or else the flag is not cleared. 15.7 Interrupts Four SPI status flags can be enabled to generate CPU interrupt requests. See Table 15-1. Table 15-1. SPI Interrupts Flag Request SPTE Transmitter empty SPI transmitter CPU interrupt request (SPTIE = 1, SPE = 1) SPRF Receiver full SPI receiver CPU interrupt request (SPRIE = 1) OVRF Overflow SPI receiver/error interrupt request (ERRIE = 1) MODF Mode fault SPI receiver/error interrupt request (ERRIE = 1) Reading the SPI status and control register with SPRF set and then reading the receive data register clears SPRF. The clearing mechanism for the SPTE flag is always just a write to the transmit data register. The SPI transmitter interrupt enable bit (SPTIE) enables the SPTE flag to generate transmitter CPU interrupt requests, provided that the SPI is enabled (SPE = 1). The SPI receiver interrupt enable bit (SPRIE) enables SPRF to generate receiver CPU interrupt requests, regardless of the state of SPE. See Figure 15-12. SPTE SPTIE SPE SPI TRANSMITTER CPU INTERRUPT REQUEST SPRIE SPRF SPI RECEIVER/ERROR ERRIE CPU INTERRUPT REQUEST MODF OVRF Figure 15-12. SPI Interrupt Request Generation MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 213 Serial Peripheral Interface (SPI) Module The error interrupt enable bit (ERRIE) enables both the MODF and OVRF bits to generate a receiver/error CPU interrupt request. The mode fault enable bit (MODFEN) can prevent the MODF flag from being set so that only the OVRF bit is enabled by the ERRIE bit to generate receiver/error CPU interrupt requests. The following sources in the SPI status and control register can generate CPU interrupt requests: * SPI receiver full bit (SPRF) -- SPRF becomes set every time a byte transfers from the shift register to the receive data register. If the SPI receiver interrupt enable bit, SPRIE, is also set, SPRF generates an SPI receiver/error CPU interrupt request. * SPI transmitter empty (SPTE) -- SPTE becomes set every time a byte transfers from the transmit data register to the shift register. If the SPI transmit interrupt enable bit, SPTIE, is also set, SPTE generates an SPTE CPU interrupt request. 15.8 Resetting the SPI Any system reset completely resets the SPI. Partial resets occur whenever the SPI enable bit (SPE) is 0. Whenever SPE is 0, the following occurs: * The SPTE flag is set. * Any transmission currently in progress is aborted. * The shift register is cleared. * The SPI state counter is cleared, making it ready for a new complete transmission. * All the SPI port logic is defaulted back to being general-purpose I/O. These items are reset only by a system reset: * All control bits in the SPCR register * All control bits in the SPSCR register (MODFEN, ERRIE, SPR1, and SPR0) * The status flags SPRF, OVRF, and MODF By not resetting the control bits when SPE is low, the user can clear SPE between transmissions without having to set all control bits again when SPE is set back high for the next transmission. By not resetting the SPRF, OVRF, and MODF flags, the user can still service these interrupts after the SPI has been disabled. The user can disable the SPI by writing 0 to the SPE bit. The SPI can also be disabled by a mode fault occurring in an SPI that was configured as a master with the MODFEN bit set. 15.9 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 15.9.1 Wait Mode The SPI module remains active after the execution of a WAIT instruction. In wait mode the SPI module registers are not accessible by the CPU. Any enabled CPU interrupt request from the SPI module can bring the MCU out of wait mode. If SPI module functions are not required during wait mode, reduce power consumption by disabling the SPI module before executing the WAIT instruction. To exit wait mode when an overflow condition occurs, enable the OVRF bit to generate CPU interrupt requests by setting the error interrupt enable bit (ERRIE). See 15.7 Interrupts. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 214 Freescale Semiconductor SPI During Break Interrupts 15.9.2 Stop Mode The SPI module is inactive after the execution of a STOP instruction. The STOP instruction does not affect register conditions. SPI operation resumes after an external interrupt. If stop mode is exited by reset, any transfer in progress is aborted, and the SPI is reset. 15.10 SPI During Break Interrupts The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. BCFE in the SIM break flag control register (SBFCR) enables software to clear status bits during the break state. See Chapter 14 System Integration Module (SIM). To allow software to clear status bits during a break interrupt, write a 1 to BCFE. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to BCFE. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a 2-step read/write clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is 0. After the break, doing the second step clears the status bit. Since the SPTE bit cannot be cleared during a break with BCFE cleared, a write to the transmit data register in break mode does not initiate a transmission nor is this data transferred into the shift register. Therefore, a write to the SPDR in break mode with BCFE cleared has no effect. 15.11 I/O Signals The SPI module has four I/O pins: * MISO -- Master input/slave output * MOSI -- Master output/slave input * SPSCK -- Serial clock * SS -- Slave select 15.11.1 MISO (Master In/Slave Out) MISO is one of the two SPI module pins that transmits serial data. In full duplex operation, the MISO pin of the master SPI module is connected to the MISO pin of the slave SPI module. The master SPI simultaneously receives data on its MISO pin and transmits data from its MOSI pin. Slave output data on the MISO pin is enabled only when the SPI is configured as a slave. The SPI is configured as a slave when its SPMSTR bit is 0 and its SS pin is low. To support a multiple-slave system, a high on the SS pin puts the MISO pin in a high-impedance state. When enabled, the SPI controls data direction of the MISO pin regardless of the state of the data direction register of the shared I/O port. 15.11.2 MOSI (Master Out/Slave In) MOSI is one of the two SPI module pins that transmits serial data. In full-duplex operation, the MOSI pin of the master SPI module is connected to the MOSI pin of the slave SPI module. The master SPI simultaneously transmits data from its MOSI pin and receives data on its MISO pin. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 215 Serial Peripheral Interface (SPI) Module When enabled, the SPI controls data direction of the MOSI pin regardless of the state of the data direction register of the shared I/O port. 15.11.3 SPSCK (Serial Clock) The serial clock synchronizes data transmission between master and slave devices. In a master MCU, the SPSCK pin is the clock output. In a slave MCU, the SPSCK pin is the clock input. In full-duplex operation, the master and slave MCUs exchange a byte of data in eight serial clock cycles. When enabled, the SPI controls data direction of the SPSCK pin regardless of the state of the data direction register of the shared I/O port. 15.11.4 SS (Slave Select) The SS pin has various functions depending on the current state of the SPI. For an SPI configured as a slave, the SS is used to select a slave. For CPHA = 0, the SS is used to define the start of a transmission. (See 15.4 Transmission Formats.) Since it is used to indicate the start of a transmission, SS must be toggled high and low between each byte transmitted for the CPHA = 0 format. However, it can remain low between transmissions for the CPHA = 1 format. See Figure 15-13. When an SPI is configured as a slave, the SS pin is always configured as an input. It cannot be used as a general-purpose I/O regardless of the state of the MODFEN control bit. However, the MODFEN bit can still prevent the state of SS from creating a MODF error. See 15.12.2 SPI Status and Control Register. MISO/MOSI BYTE 1 BYTE 2 BYTE 3 MASTER SS SLAVE SS CPHA = 0 SLAVE SS CPHA = 1 Figure 15-13. CPHA/SS Timing NOTE A high on the SS pin of a slave SPI puts the MISO pin in a high-impedance state. The slave SPI ignores all incoming SPSCK clocks, even if it was already in the middle of a transmission. When an SPI is configured as a master, the SS input can be used in conjunction with the MODF flag to prevent multiple masters from driving MOSI and SPSCK. (See 15.6.2 Mode Fault Error.) For the state of the SS pin to set the MODF flag, the MODFEN bit in the SPSCK register must be set. If MODFEN is 0 for an SPI master, the SS pin can be used as a general-purpose I/O under the control of the data direction register of the shared I/O port. When MODFEN is 1, SS is an input-only pin to the SPI regardless of the state of the data direction register of the shared I/O port. The CPU can always read the state of the SS pin by configuring the appropriate pin as an input and reading the port data register. See Table 15-2. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 216 Freescale Semiconductor I/O Registers Table 15-2. SPI Configuration SPE SPMSTR MODFEN SPI Configuration Function of SS Pin 0 X(1)) X Not enabled General-purpose I/O; SS ignored by SPI 1 0 X Slave Input-only to SPI 1 1 0 Master without MODF General-purpose I/O; SS ignored by SPI 1 1 1 Master with MODF Input-only to SPI 1. X = Don't care 15.12 I/O Registers Three registers control and monitor SPI operation: * SPI control register (SPCR) * SPI status and control register (SPSCR) * SPI data register (SPDR) 15.12.1 SPI Control Register The SPI control register: * Enables SPI module interrupt requests * Configures the SPI module as master or slave * Selects serial clock polarity and phase * Configures the SPSCK, MOSI, and MISO pins as open-drain outputs * Enables the SPI module Address: $0010 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 SPRIE R SPMSTR CPOL CPHA SPWOM SPE SPTIE 0 0 1 0 1 0 0 0 R = Reserved Figure 15-14. SPI Control Register (SPCR) SPRIE -- SPI Receiver Interrupt Enable Bit This read/write bit enables CPU interrupt requests generated by the SPRF bit. The SPRF bit is set when a byte transfers from the shift register to the receive data register. Reset clears the SPRIE bit. 1 = SPRF CPU interrupt requests enabled 0 = SPRF CPU interrupt requests disabled SPMSTR -- SPI Master Bit This read/write bit selects master mode operation or slave mode operation. Reset sets the SPMSTR bit. 1 = Master mode 0 = Slave mode MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 217 Serial Peripheral Interface (SPI) Module CPOL -- Clock Polarity Bit This read/write bit determines the logic state of the SPSCK pin between transmissions. (See Figure 15-5 and Figure 15-7.) To transmit data between SPI modules, the SPI modules must have identical CPOL values. Reset clears the CPOL bit. CPHA -- Clock Phase Bit This read/write bit controls the timing relationship between the serial clock and SPI data. (See Figure 15-5 and Figure 15-7.) To transmit data between SPI modules, the SPI modules must have identical CPHA values. When CPHA = 0, the SS pin of the slave SPI module must be high between bytes. (See Figure 15-13.) Reset sets the CPHA bit. SPWOM -- SPI Wired-OR Mode Bit This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins become open-drain outputs. 1 = Wired-OR SPSCK, MOSI, and MISO pins 0 = Normal push-pull SPSCK, MOSI, and MISO pins SPE -- SPI Enable This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI. (See 15.8 Resetting the SPI.) Reset clears the SPE bit. 1 = SPI module enabled 0 = SPI module disabled SPTIE-- SPI Transmit Interrupt Enable This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte transfers from the transmit data register to the shift register. Reset clears the SPTIE bit. 1 = SPTE CPU interrupt requests enabled 0 = SPTE CPU interrupt requests disabled 15.12.2 SPI Status and Control Register The SPI status and control register contains flags to signal these conditions: * Receive data register full * Failure to clear SPRF bit before next byte is received (overflow error) * Inconsistent logic level on SS pin (mode fault error) * Transmit data register empty The SPI status and control register also contains bits that perform these functions: * Enable error interrupts * Enable mode fault error detection * Select master SPI baud rate Address: $0011 Bit 7 Read: SPRF Write: Reset: 0 6 ERRIE 0 5 4 3 OVRF MODF SPTE 0 0 1 2 1 Bit 0 MODFEN SPR1 SPR0 0 0 0 = Unimplemented Figure 15-15. SPI Status and Control Register (SPSCR) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 218 Freescale Semiconductor I/O Registers SPRF -- SPI Receiver Full Bit This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data register. SPRF generates a CPU interrupt request if the SPRIE bit in the SPI control register is set also. During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status and control register with SPRF set and then reading the SPI data register. Reset clears the SPRF bit. 1 = Receive data register full 0 = Receive data register not full ERRIE -- Error Interrupt Enable Bit This read/write bit enables the MODF and OVRF bits to generate CPU interrupt requests. Reset clears the ERRIE bit. 1 = MODF and OVRF can generate CPU interrupt requests 0 = MODF and OVRF cannot generate CPU interrupt requests OVRF -- Overflow Bit This clearable, read-only flag is set if software does not read the byte in the receive data register before the next full byte enters the shift register. In an overflow condition, the byte already in the receive data register is unaffected, and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI status and control register with OVRF set and then reading the receive data register. Reset clears the OVRF bit. 1 = Overflow 0 = No overflow MODF -- Mode Fault Bit This clearable, read-only flag is set in a slave SPI if the SS pin goes high during a transmission with MODFEN set. In a master SPI, the MODF flag is set if the SS pin goes low at any time with the MODFEN bit set. Clear MODF by reading the SPI status and control register (SPSCR) with MODF set and then writing to the SPI control register (SPCR). Reset clears the MODF bit. 1 = SS pin at inappropriate logic level 0 = SS pin at appropriate logic level SPTE -- SPI Transmitter Empty Bit This clearable, read-only flag is set each time the transmit data register transfers a byte into the shift register. SPTE generates an SPTE CPU interrupt request if SPTIE in the SPI control register is set also. NOTE Do not write to the SPI data register unless SPTE is high. During an SPTE CPU interrupt, the CPU clears SPTE by writing to the transmit data register. Reset sets the SPTE bit. 1 = Transmit data register empty 0 = Transmit data register not empty MODFEN -- Mode Fault Enable Bit This read/write bit, when set, allows the MODF flag to be set. If the MODF flag is set, clearing MODFEN does not clear the MODF flag. If the SPI is enabled as a master and the MODFEN bit is 0, then the SS pin is available as a general-purpose I/O. If the MODFEN bit is 1, then the SS pin is not available as a general-purpose I/O. When the SPI is enabled as a slave, the SS pin is not available as a general-purpose I/O regardless of the value of MODFEN. See 15.11.4 SS (Slave Select). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 219 Serial Peripheral Interface (SPI) Module If the MODFEN bit is 0, the level of the SS pin does not affect the operation of an enabled SPI configured as a master. For an enabled SPI configured as a slave, having MODFEN low only prevents the MODF flag from being set. It does not affect any other part of SPI operation. See 15.6.2 Mode Fault Error. SPR1 and SPR0 -- SPI Baud Rate Select Bits In master mode, these read/write bits select one of four baud rates as shown in Table 15-3. SPR1 and SPR0 have no effect in slave mode. Reset clears SPR1 and SPR0. Table 15-3. SPI Master Baud Rate Selection SPR1 and SPR0 Baud Rate Divisor (BD) 00 2 01 8 10 32 11 128 Use this formula to calculate the SPI baud rate: Baud rate = BUSCLK BD 15.12.3 SPI Data Register The SPI data register consists of the read-only receive data register and the write-only transmit data register. Writing to the SPI data register writes data into the transmit data register. Reading the SPI data register reads data from the receive data register. The transmit data and receive data registers are separate registers that can contain different values. See Figure 15-2. Address: $0012 Bit 7 6 5 4 3 2 1 Bit 0 Read: R7 R6 R5 R4 R3 R2 R1 R0 Write: T7 T6 T5 T4 T3 T2 T1 T0 Reset: Unaffected by reset Figure 15-16. SPI Data Register (SPDR) R7-R0/T7-T0 -- Receive/Transmit Data Bits NOTE Do not use read-modify-write instructions on the SPI data register since the register read is not the same as the register written. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 220 Freescale Semiconductor Chapter 16 Timebase Module (TBM) 16.1 Introduction This section describes the timebase module (TBM). The TBM will generate periodic interrupts at user selectable rates using a counter clocked by the external clock source. This TBM version uses 15 divider stages, eight of which are user selectable. A configuration option bit to select an additional 128 divide of the external clock source can be selected. See Chapter 5 Configuration Register (CONFIG) 16.2 Features Features of the TBM module include: * External clock or an additional divide-by-128 selected by configuration option bit as clock source * Software configurable periodic interrupts with divide-by: 8, 16, 32, 64, 128, 2048, 8192, and 32768 taps of the selected clock source * Configurable for operation during stop mode to allow periodic wakeup from stop 16.3 Functional Description This module can generate a periodic interrupt by dividing the clock source supplied from the clock generator module, CGMXCLK. The counter is initialized to all 0s when TBON bit is cleared. The counter, shown in Figure 16-1, starts counting when the TBON bit is set. When the counter overflows at the tap selected by TBR2-TBR0, the TBIF bit gets set. If the TBIE bit is set, an interrupt request is sent to the CPU. The TBIF flag is cleared by writing a 1 to the TACK bit. The first time the TBIF flag is set after enabling the timebase module, the interrupt is generated at approximately half of the overflow period. Subsequent events occur at the exact period. The timebase module may remain active after execution of the STOP instruction if the crystal oscillator has been enabled to operate during stop mode through the OSCENINSTOP bit in the configuration register. The timebase module can be used in this mode to generate a periodic wakeup from stop mode. 16.4 Interrupts The timebase module can periodically interrupt the CPU with a rate defined by the selected TBMCLK and the select bits TBR2-TBR0. When the timebase counter chain rolls over, the TBIF flag is set. If the TBIE bit is set, enabling the timebase interrupt, the counter chain overflow will generate a CPU interrupt request. NOTE Interrupts must be acknowledged by writing a 1 to the TACK bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 221 Timebase Module (TBM) TMBCLKSEL FROM CONFIG2 CGMXCLK FROM CGM MODULE TBMCLK 0 1 DIVIDE BY 128 PRESCALER TBON /2 /2 /2 /2 /2 /2 /2 /2 /2 /2 /2 /2 TACK /2 TBR0 /2 TBR1 /2 TBR2 TBMINT TBIF 000 TBIE R 001 010 100 SEL 011 101 110 111 Figure 16-1. Timebase Block Diagram 16.5 TBM Interrupt Rate The interrupt rate is determined by the equation: tTBMRATE = Divider fCGMXCLK where: fCGMXCLK = Frequency supplied from the clock generator (CGM) module Divider = Divider value as determined by TBR2-TBR0 settings and TMBCLKSEL, see Table 16-1 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 222 Freescale Semiconductor Low-Power Modes Table 16-1. Timebase Divider Selection Divider TBR2 TBR1 TBR0 0 0 0 0 0 TMBCLKSEL 0 1 0 32,768 4,194,304 1 8192 1,048,576 1 0 2048 262144 0 1 1 128 16,384 1 0 0 64 8192 1 0 1 32 4096 1 1 0 16 2048 1 1 1 8 1024 As an example, a 4.9152 MHz crystal, with the TMBCLKSEL set for divide-by-128 and the TBR2-TBR0 set to {011}, the divider is 16,384 and the interrupt rate calculates to: 16,384 4.9152 x 106 = 3.33 ms NOTE Do not change TBR2-TBR0 bits while the timebase is enabled (TBON = 1). 16.6 Low-Power Modes The WAIT and STOP instructions put the MCU in low power- consumption standby modes. 16.6.1 Wait Mode The timebase module remains active after execution of the WAIT instruction. In wait mode the timebase register is not accessible by the CPU. If the timebase functions are not required during wait mode, reduce the power consumption by stopping the timebase before executing the WAIT instruction. 16.6.2 Stop Mode The timebase module may remain active after execution of the STOP instruction if the oscillator has been enabled to operate during stop mode through the OSCENINSTOP bit in the configuration register. The timebase module can be used in this mode to generate a periodic wakeup from stop mode. If the oscillator has not been enabled to operate in stop mode, the timebase module will not be active during stop mode. In stop mode, the timebase register is not accessible by the CPU. If the timebase functions are not required during stop mode, reduce power consumption by disabling the timebase module before executing the STOP instruction. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 223 Timebase Module (TBM) 16.7 Timebase Control Register The timebase has one register, the timebase control register (TBCR), which is used to enable the timebase interrupts and set the rate. Address: $001C Bit 7 Read: TBIF Write: Reset: 0 6 5 4 TBR2 TBR1 TBR0 0 0 0 = Unimplemented 3 2 1 Bit 0 TBIE TBON R 0 0 0 0 R = Reserved 0 TACK Figure 16-2. Timebase Control Register (TBCR) TBIF -- Timebase Interrupt Flag This read-only flag bit is set when the timebase counter has rolled over. 1 = Timebase interrupt pending 0 = Timebase interrupt not pending TBR2-TBR0 -- Timebase Divider Selection Bits These read/write bits select the tap in the counter to be used for timebase interrupts as shown in Table 16-1. NOTE Do not change TBR2-TBR0 bits while the timebase is enabled (TBON = 1). TACK-- Timebase Acknowledge Bit The TACK bit is a write-only bit and always reads as 0. Writing a 1 to this bit clears TBIF, the timebase interrupt flag bit. Writing a 0 to this bit has no effect. 1 = Clear timebase interrupt flag 0 = No effect TBIE -- Timebase Interrupt Enabled Bit This read/write bit enables the timebase interrupt when the TBIF bit becomes set. Reset clears the TBIE bit. 1 = Timebase interrupt is enabled. 0 = Timebase interrupt is disabled. TBON -- Timebase Enabled Bit This read/write bit enables the timebase. Timebase may be turned off to reduce power consumption when its function is not necessary. The counter can be initialized by clearing and then setting this bit. Reset clears the TBON bit. 1 = Timebase is enabled. 0 = Timebase is disabled and the counter initialized to 0s. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 224 Freescale Semiconductor Chapter 17 Timer Interface Module (TIM1) 17.1 Introduction This section describes the timer interface module (TIM1). TIM1 is a two-channel timer that provides a timing reference with input capture, output compare, and pulse-width-modulation functions. Figure 17-2 is a block diagram of the TIM1. 17.2 Features Features of the TIM1 include the following: * Two input capture/output compare channels - Rising-edge, falling-edge, or any-edge input capture trigger - Set, clear, or toggle output compare action * Buffered and unbuffered pulse width modulation (PWM) signal generation * Programmable TIM1 clock input with 7-frequency internal bus clock prescaler selection * Free-running or modulo up-count operation * Toggle any channel pin on overflow * TIM1 counter stop and reset bits 17.3 Functional Description Figure 17-2 shows the structure of the TIM1. The central component of the TIM1 is the 16-bit TIM1 counter that can operate as a free-running counter or a modulo up-counter. The TIM1 counter provides the timing reference for the input capture and output compare functions. The TIM1 counter modulo registers, T1MODH:T1MODL, control the modulo value of the TIM1 counter. Software can read the TIM1 counter value at any time without affecting the counting sequence. The two TIM1 channels are programmable independently as input capture or output compare channels. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 225 Timer Interface Module (TIM1) INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 17-1. Block Diagram Highlighting TIM1 Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 226 Freescale Semiconductor Functional Description PRESCALER SELECT INTERNAL BUS CLOCK PRESCALER TSTOP PS2 TRST PS1 PS0 16-BIT COUNTER TOF INTERRUPT LOGIC TOIE 16-BIT COMPARATOR T1MODH:T1MODL TOV0 CHANNEL 0 ELS0B ELS0A PORT LOGIC CH0MAX 16-BIT COMPARATOR T1CH0H:T1CH0L PTD4/T1CH0 CH0F INTERRUPT LOGIC 16-BIT LATCH CH0IE MS0A MS0B INTERNAL BUS TOV1 CHANNEL 1 ELS1B ELS1A PORT LOGIC CH1MAX 16-BIT COMPARATOR T1CH1H:T1CH1L PTD5/T1CH1 CH1F INTERRUPT LOGIC 16-BIT LATCH CH1IE MS1A Figure 17-2. TIM1 Block Diagram Addr. Register Name $0020 TIM1 Status and Control Register (T1SC) See page 234. $0021 $0022 TIM1 Counter Register High (T1CNTH) See page 235. TIM1 Counter Register Low (T1CNTL) See page 235. Bit 7 Read: TOF Write: 0 6 5 TOIE TSTOP 4 3 0 0 TRST 2 1 Bit 0 PS2 PS1 PS0 Reset: 0 0 1 0 0 0 0 0 Read: Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: 0 0 0 0 0 0 0 0 Read: Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Write: Write: Reset: = Unimplemented Figure 17-3. TIM1 I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 227 Timer Interface Module (TIM1) Addr. $0023 $0024 $0025 $0026 $0027 $0028 $0029 $002A Register Name TIM1 Counter Modulo Register High (T1MODH) See page 236. TIM1 Counter Modulo Register Low (T1MODL) See page 236. TIM1 Channel 0 Status and Control Register (T1SC0) See page 237. TIM1 Channel 0 Register High (T1CH0H) See page 240. TIM1 Channel 0 Register Low (T1CH0L) See page 240. TIM1 Channel 1 Status and Control Register (T1SC1) See page 237. TIM1 Channel 1 Register High (T1CH1H) See page 240. TIM1 Channel 1 Register Low (T1CH1L) See page 240. Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 1 1 1 1 1 1 1 1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset: 1 1 1 1 1 1 1 1 Read: CH0F Write: 0 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX Reset: 0 0 0 0 0 0 0 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 2 Bit 1 Bit 0 Read: Write: Reset: Read: Write: Read: Write: Reset: Read: Write: Indeterminate after reset Bit 7 Bit 6 Bit 5 Reset: CH1F Write: 0 Reset: 0 0 Bit 15 Bit 14 Write: CH1IE 0 MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 0 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 2 Bit 1 Bit 0 Reset: Read: Write: Bit 3 Indeterminate after reset Read: Read: Bit 4 Indeterminate after reset Bit 7 Bit 6 Bit 5 Reset: Bit 4 Bit 3 Indeterminate after reset = Unimplemented Figure 17-3. TIM1 I/O Register Summary (Continued) 17.3.1 TIM1 Counter Prescaler The TIM1 clock source is one of the seven prescaler outputs. The prescaler generates seven clock rates from the internal bus clock. The prescaler select bits, PS[2:0], in the TIM1 status and control register (T1SC) select the TIM1 clock source. 17.3.2 Input Capture With the input capture function, the TIM1 can capture the time at which an external event occurs. When an active edge occurs on the pin of an input capture channel, the TIM1 latches the contents of the TIM1 counter into the TIM1 channel registers, T1CHxH:T1CHxL. The polarity of the active edge is programmable. Input captures can generate TIM1 central processor unit (CPU) interrupt requests. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 228 Freescale Semiconductor Functional Description 17.3.3 Output Compare With the output compare function, the TIM1 can generate a periodic pulse with a programmable polarity, duration, and frequency. When the counter reaches the value in the registers of an output compare channel, the TIM1 can set, clear, or toggle the channel pin. Output compares can generate TIM1 CPU interrupt requests. 17.3.3.1 Unbuffered Output Compare Any output compare channel can generate unbuffered output compare pulses as described in 17.3.3 Output Compare. The pulses are unbuffered because changing the output compare value requires writing the new value over the old value currently in the TIM1 channel registers. An unsynchronized write to the TIM1 channel registers to change an output compare value could cause incorrect operation for up to two counter overflow periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that counter overflow period. Also, using a TIM1 overflow interrupt routine to write a new, smaller output compare value may cause the compare to be missed. The TIM1 may pass the new value before it is written. Use the following methods to synchronize unbuffered changes in the output compare value on channel x: * When changing to a smaller value, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current output compare pulse. The interrupt routine has until the end of the counter overflow period to write the new value. * When changing to a larger output compare value, enable TIM1 overflow interrupts and write the new value in the TIM1 overflow interrupt routine. The TIM1 overflow interrupt occurs at the end of the current counter overflow period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same counter overflow period. 17.3.3.2 Buffered Output Compare Channels 0 and 1 can be linked to form a buffered output compare channel whose output appears on the T1CH0 pin. The TIM1 channel registers of the linked pair alternately control the output. Setting the MS0B bit in TIM1 channel 0 status and control register (TSC0) links channel 0 and channel 1. The output compare value in the TIM1 channel 0 registers initially controls the output on the T1CH0 pin. Writing to the TIM1 channel 1 registers enables the TIM1 channel 1 registers to synchronously control the output after the TIM1 overflows. At each subsequent overflow, the TIM1 channel registers (0 or 1) that control the output are the ones written to last. T1SC0 controls and monitors the buffered output compare function, and TIM1 channel 1 status and control register (T1SC1) is unused. While the MS0B bit is set, the channel 1 pin, T1CH1, is available as a general-purpose I/O pin. NOTE In buffered output compare operation, do not write new output compare values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered output compares. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 229 Timer Interface Module (TIM1) 17.3.4 Pulse Width Modulation (PWM) By using the toggle-on-overflow feature with an output compare channel, the TIM1 can generate a PWM signal. The value in the TIM1 counter modulo registers determines the period of the PWM signal. The channel pin toggles when the counter reaches the value in the TIM1 counter modulo registers. The time between overflows is the period of the PWM signal. As Figure 17-4 shows, the output compare value in the TIM1 channel registers determines the pulse width of the PWM signal. The time between overflow and output compare is the pulse width. Program the TIM1 to clear the channel pin on output compare if the polarity of the PWM pulse is 1 (ELSxA = 0). Program the TIM1 to set the pin if the polarity of the PWM pulse is 0 (ELSxA = 1). The value in the TIM1 counter modulo registers and the selected prescaler output determines the frequency of the PWM output. The frequency of an 8-bit PWM signal is variable in 256 increments. Writing $00FF (255) to the TIM1 counter modulo registers produces a PWM period of 256 times the internal bus clock period if the prescaler select value is 000. See 17.8.1 TIM1 Status and Control Register. The value in the TIM1 channel registers determines the pulse width of the PWM output. The pulse width of an 8-bit PWM signal is variable in 256 increments. Writing $0080 (128) to the TIM1 channel registers produces a duty cycle of 128/256 or 50%. OVERFLOW OVERFLOW OVERFLOW PERIOD POLARITY = 1 (ELSxA = 0) TCHx PULSE WIDTH POLARITY = 0 (ELSxA = 1) TCHx OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 17-4. PWM Period and Pulse Width 17.3.4.1 Unbuffered PWM Signal Generation Any output compare channel can generate unbuffered PWM pulses as described in 17.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because changing the pulse width requires writing the new pulse width value over the old value currently in the TIM1 channel registers. An unsynchronized write to the TIM1 channel registers to change a pulse width value could cause incorrect operation for up to two PWM periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that PWM period. Also, using a TIM1 overflow interrupt routine to write a new, smaller pulse width value may cause the compare to be missed. The TIM1 may pass the new value before it is written to the timer channel (T1CHxH:T1CHxL) registers. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 230 Freescale Semiconductor Functional Description Use the following methods to synchronize unbuffered changes in the PWM pulse width on channel x: * When changing to a shorter pulse width, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current pulse. The interrupt routine has until the end of the PWM period to write the new value. * When changing to a longer pulse width, enable TIM1 overflow interrupts and write the new value in the TIM1 overflow interrupt routine. The TIM1 overflow interrupt occurs at the end of the current PWM period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same PWM period. NOTE In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare also can cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 17.3.4.2 Buffered PWM Signal Generation Channels 0 and 1 can be linked to form a buffered PWM channel whose output appears on the T1CH0 pin. The TIM1 channel registers of the linked pair alternately control the pulse width of the output. Setting the MS0B bit in TIM1 channel 0 status and control register (T1SC0) links channel 0 and channel 1. The TIM1 channel 0 registers initially control the pulse width on the T1CH0 pin. Writing to the TIM1 channel 1 registers enables the TIM1 channel 1 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIM1 channel registers (0 or 1) that control the pulse width are the ones written to last. T1SC0 controls and monitors the buffered PWM function, and TIM1 channel 1 status and control register (T1SC1) is unused. While the MS0B bit is set, the channel 1 pin, T1CH1, is available as a general-purpose I/O pin. NOTE In buffered PWM signal generation, do not write new pulse width values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered PWM signals. 17.3.4.3 PWM Initialization To ensure correct operation when generating unbuffered or buffered PWM signals, use the following initialization procedure: 1. In the TIM1 status and control register (T1SC): a. Stop the TIM1 counter by setting the TIM1 stop bit, TSTOP. b. Reset the TIM1 counter and prescaler by setting the TIM1 reset bit, TRST. 2. In the TIM1 counter modulo registers (T1MODH:T1MODL), write the value for the required PWM period. 3. In the TIM1 channel x registers (T1CHxH:T1CHxL), write the value for the required pulse width. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 231 Timer Interface Module (TIM1) 4. In TIM1 channel x status and control register (T1SCx): a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for buffered output compare or PWM signals) to the mode select bits, MSxB:MSxA. See Table 17-2. b. Write 1 to the toggle-on-overflow bit, TOVx. c. Write 1:0 (polarity 1 -- to clear output on compare) or 1:1 (polarity 0 -- to set output on compare) to the edge/level select bits, ELSxB:ELSxA. The output action on compare must force the output to the complement of the pulse width level. See Table 17-2. NOTE In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare can also cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 5. In the TIM1 status control register (T1SC), clear the TIM1 stop bit, TSTOP. Setting MS0B links channels 0 and 1 and configures them for buffered PWM operation. The TIM1 channel 0 registers (TCH0H:TCH0L) initially control the buffered PWM output. TIM1 status control register 0 (TSCR0) controls and monitors the PWM signal from the linked channels. MS0B takes priority over MS0A. Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM1 overflows. Subsequent output compares try to force the output to a state it is already in and have no effect. The result is a 0% duty cycle output. Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit generates a 100% duty cycle output. See 17.8.4 TIM1 Channel Status and Control Registers. 17.4 Interrupts The following TIM1 sources can generate interrupt requests: * TIM1 overflow flag (TOF) -- The TOF bit is set when the TIM1 counter reaches the modulo value programmed in the TIM1 counter modulo registers. The TIM1 overflow interrupt enable bit, TOIE, enables TIM1 overflow CPU interrupt requests. TOF and TOIE are in the TIM1 status and control register. * TIM1 channel flags (CH1F:CH0F) -- The CHxF bit is set when an input capture or output compare occurs on channel x. Channel x TIM CPU interrupt requests are controlled by the channel x interrupt enable bit, CHxIE. Channel x TIM CPU interrupt requests are enabled when CHxIE =1. CHxF and CHxIE are in the TIM1 channel x status and control register. 17.5 Wait Mode The WAIT instruction puts the MCU in low power-consumption standby mode. The TIM1 remains active after the execution of a WAIT instruction. In wait mode the TIM1 registers are not accessible by the CPU. Any enabled CPU interrupt request from the TIM1 can bring the MCU out of wait mode. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 232 Freescale Semiconductor TIM1 During Break Interrupts If TIM1 functions are not required during wait mode, reduce power consumption by stopping the TIM1 before executing the WAIT instruction. 17.6 TIM1 During Break Interrupts A break interrupt stops the TIM1 counter and inhibits input captures. The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status bits during the break state. See Figure 14-21. Break Status Register (BSR). To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a two-step read/write clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. 17.7 Input/Output Signals Port D shares two of its pins with the TIM1. The two TIM1 channel I/O pins are PTD4/T1CH0 and PTD5/T1CH1. Each channel I/O pin is programmable independently as an input capture pin or an output compare pin. PTD4/T1CH0 can be configured as a buffered output compare or buffered PWM pin. 17.8 Input/Output Registers The following I/O registers control and monitor operation of the TIM: * TIM1 status and control register (T1SC) * TIM1 counter registers (T1CNTH:T1CNTL) * TIM1 counter modulo registers (T1MODH:T1MODL) * TIM1 channel status and control registers (T1SC0 and T1SC1) * TIM1 channel registers (T1CH0H:T1CH0L and T1CH1H:T1CH1L) 17.8.1 TIM1 Status and Control Register The TIM1 status and control register (T1SC) does the following: * Enables TIM1 overflow interrupts * Flags TIM1 overflows * Stops the TIM1 counter * Resets the TIM1 counter * Prescales the TIM1 counter clock MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 233 Timer Interface Module (TIM1) Address: $0020 Bit 7 Read: TOF Write: 0 Reset: 0 6 5 TOIE TSTOP 0 1 4 3 0 0 TRST 0 0 2 1 Bit 0 PS2 PS1 PS0 0 0 0 = Unimplemented Figure 17-5. TIM1 Status and Control Register (T1SC) TOF -- TIM1 Overflow Flag Bit This read/write flag is set when the TIM1 counter reaches the modulo value programmed in the TIM1 counter modulo registers. Clear TOF by reading the TIM1 status and control register when TOF is set and then writing a 0 to TOF. If another TIM1 overflow occurs before the clearing sequence is complete, then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF has no effect. 1 = TIM1 counter has reached modulo value 0 = TIM1 counter has not reached modulo value TOIE -- TIM1 Overflow Interrupt Enable Bit This read/write bit enables TIM1 overflow interrupts when the TOF bit becomes set. Reset clears the TOIE bit. 1 = TIM1 overflow interrupts enabled 0 = TIM1 overflow interrupts disabled TSTOP -- TIM1 Stop Bit This read/write bit stops the TIM1 counter. Counting resumes when TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIM1 counter until software clears the TSTOP bit. 1 = TIM1 counter stopped 0 = TIM1 counter active NOTE Do not set the TSTOP bit before entering wait mode if the TIM1 is required to exit wait mode. Also, when the TSTOP bit is set and the timer is configured for input capture operation, input captures are inhibited until the TSTOP bit is cleared. TRST -- TIM1 Reset Bit Setting this write-only bit resets the TIM1 counter and the TIM1 prescaler. Setting TRST has no effect on any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIM1 counter is reset and always reads as 0. Reset clears the TRST bit. 1 = Prescaler and TIM1 counter cleared 0 = No effect NOTE Setting the TSTOP and TRST bits simultaneously stops the TIM1 counter at a value of $0000. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 234 Freescale Semiconductor Input/Output Registers PS[2:0] -- Prescaler Select Bits These read/write bits select one of the seven prescaler outputs as the input to the TIM1 counter as Table 17-1 shows. Reset clears the PS[2:0] bits. Table 17-1. Prescaler Selection PS2 PS1 PS0 TIM1 Clock Source 0 0 0 Internal bus clock / 1 0 0 1 Internal bus clock / 2 0 1 0 Internal bus clock / 4 0 1 1 Internal bus clock / 8 1 0 0 Internal bus clock / 16 1 0 1 Internal bus clock / 32 1 1 0 Internal bus clock / 64 1 1 1 Not available 17.8.2 TIM1 Counter Registers The two read-only TIM1 counter registers contain the high and low bytes of the value in the TIM1 counter. Reading the high byte (T1CNTH) latches the contents of the low byte (T1CNTL) into a buffer. Subsequent reads of T1CNTH do not affect the latched T1CNTL value until T1CNTL is read. Reset clears the TIM1 counter registers. Setting the TIM1 reset bit (TRST) also clears the TIM1 counter registers. NOTE If you read T1CNTH during a break interrupt, be sure to unlatch T1CNTL by reading T1CNTL before exiting the break interrupt. Otherwise, T1CNTL retains the value latched during the break. Address: $0021 Read: T1CNTH Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Write: Reset: Address: $0022 Read: T1CNTL Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 17-6. TIM1 Counter Registers (T1CNTH:T1CNTL) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 235 Timer Interface Module (TIM1) 17.8.3 TIM1 Counter Modulo Registers The read/write TIM1 modulo registers contain the modulo value for the TIM1 counter. When the TIM1 counter reaches the modulo value, the overflow flag (TOF) becomes set, and the TIM1 counter resumes counting from $0000 at the next timer clock. Writing to the high byte (T1MODH) inhibits the TOF bit and overflow interrupts until the low byte (T1MODL) is written. Reset sets the TIM1 counter modulo registers. Address: $0023 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 Bit15 Bit14 Bit13 Bit12 Bit11 Bit10 Bit9 Bit8 1 1 1 1 1 1 1 1 Address: $0024 Read: Write: Reset: T1MODH T1MODL Bit 7 6 5 4 3 2 1 Bit 0 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 1 1 1 1 1 1 1 1 Figure 17-7. TIM1 Counter Modulo Registers (T1MODH:T1MODL) NOTE Reset the TIM1 counter before writing to the TIM1 counter modulo registers. 17.8.4 TIM1 Channel Status and Control Registers Each of the TIM1 channel status and control registers does the following: * Flags input captures and output compares * Enables input capture and output compare interrupts * Selects input capture, output compare, or PWM operation * Selects high, low, or toggling output on output compare * Selects rising edge, falling edge, or any edge as the active input capture trigger * Selects output toggling on TIM1 overflow * Selects 0% and 100% PWM duty cycle * Selects buffered or unbuffered output compare/PWM operation MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 236 Freescale Semiconductor Input/Output Registers Address: $0025 Bit 7 T1SC0 6 5 4 3 2 1 Bit 0 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX 0 0 0 0 0 0 5 4 3 2 1 Bit 0 MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 Read: CH0F Write: 0 Reset: 0 0 Address: $0028 T1SC1 Bit 7 Read: CH1F Write: 0 Reset: 0 6 CH1IE 0 0 0 = Unimplemented Figure 17-8. TIM1 Channel Status and Control Registers (T1SC0:T1SC1) CHxF -- Channel x Flag Bit When channel x is an input capture channel, this read/write bit is set when an active edge occurs on the channel x pin. When channel x is an output compare channel, CHxF is set when the value in the TIM1 counter registers matches the value in the TIM1 channel x registers. Clear CHxF by reading the TIM1 channel x status and control register with CHxF set and then writing a 0 to CHxF. If another interrupt request occurs before the clearing sequence is complete, then writing 0 to CHxF has no effect. Therefore, an interrupt request cannot be lost due to inadvertent clearing of CHxF. Reset clears the CHxF bit. Writing a 1 to CHxF has no effect. 1 = Input capture or output compare on channel x 0 = No input capture or output compare on channel x CHxIE -- Channel x Interrupt Enable Bit This read/write bit enables TIM1 CPU interrupt service requests on channel x. Reset clears the CHxIE bit. 1 = Channel x CPU interrupt requests enabled 0 = Channel x CPU interrupt requests disabled MSxB -- Mode Select Bit B This read/write bit selects buffered output compare/PWM operation. MSxB exists only in the TIM1 channel 0 status and control register. Setting MS0B disables the channel 1 status and control register and reverts T1CH1 to general-purpose I/O. Reset clears the MSxB bit. 1 = Buffered output compare/PWM operation enabled 0 = Buffered output compare/PWM operation disabled MSxA -- Mode Select Bit A When ELSxB:A 00, this read/write bit selects either input capture operation or unbuffered output compare/PWM operation. See Table 17-2. 1 = Unbuffered output compare/PWM operation 0 = Input capture operation MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 237 Timer Interface Module (TIM1) When ELSxB:A = 00, this read/write bit selects the initial output level of the TCHx pin (see Table 17-2). Reset clears the MSxA bit. 1 = Initial output level low 0 = Initial output level high NOTE Before changing a channel function by writing to the MSxB or MSxA bit, set the TSTOP and TRST bits in the TIM1 status and control register (T1SC). ELSxB and ELSxA -- Edge/Level Select Bits When channel x is an input capture channel, these read/write bits control the active edge-sensing logic on channel x. When channel x is an output compare channel, ELSxB and ELSxA control the channel x output behavior when an output compare occurs. When ELSxB and ELSxA are both clear, channel x is not connected to an I/O port, and pin TCHx is available as a general-purpose I/O pin. Table 17-2 shows how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits. Table 17-2. Mode, Edge, and Level Selection MSxB MSxA ELSxB ELSxA Mode X 0 0 0 X 1 0 0 Pin under port control; initial output level low 0 0 0 1 Capture on rising edge only 0 0 1 0 0 0 1 1 Capture on rising or falling edge 0 1 0 0 Software compare only 0 1 0 1 0 1 1 0 0 1 1 1 1 X 0 1 1 X 1 0 1 X 1 1 Output preset Input capture Output compare or PWM Configuration Pin under port control; initial output level high Capture on falling edge only Toggle output on compare Clear output on compare Set output on compare Buffered output compare or buffered PWM Toggle output on compare Clear output on compare Set output on compare NOTE After initially enabling a TIM1 channel register for input capture operation and selecting the edge sensitivity, clear CHxF to ignore any erroneous edge detection flags. TOVx -- Toggle-On-Overflow Bit When channel x is an output compare channel, this read/write bit controls the behavior of the channel x output when the TIM1 counter overflows. When channel x is an input capture channel, TOVx has no effect. Reset clears the TOVx bit. 1 = Channel x pin toggles on TIM1 counter overflow. 0 = Channel x pin does not toggle on TIM1 counter overflow. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 238 Freescale Semiconductor Input/Output Registers NOTE When TOVx is set, a TIM1 counter overflow takes precedence over a channel x output compare if both occur at the same time. CHxMAX -- Channel x Maximum Duty Cycle Bit When the TOVx bit is at 1, setting the CHxMAX bit forces the duty cycle of buffered and unbuffered PWM signals to 100%. As Figure 17-9 shows, the CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays at the 100% duty cycle level until the cycle after CHxMAX is cleared. NOTE The 100% PWM duty cycle is defined as a continuous high level if the PWM polarity is 1 and a continuous low level if the PWM polarity is 0. Conversely, a 0% PWM duty cycle is defined as a continuous low level if the PWM polarity is 1 and a continuous high level if the PWM polarity is 0. OVERFLOW OVERFLOW OVERFLOW OVERFLOW OVERFLOW PERIOD TCHx OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE CHxMAX Figure 17-9. CHxMAX Latency 17.8.5 TIM1 Channel Registers These read/write registers contain the captured TIM1 counter value of the input capture function or the output compare value of the output compare function. The state of the TIM1 channel registers after reset is unknown. In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the TIM1 channel x registers (T1CHxH) inhibits input captures until the low byte (T1CHxL) is read. In output compare mode (MSxB:MSxA 0:0), writing to the high byte of the TIM1 channel x registers (T1CHxH) inhibits output compares until the low byte (T1CHxL) is written. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 239 Timer Interface Module (TIM1) Address: $0026 Read: Write: T1CH0H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $0027 Read: Write: T1CH0L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset: Indeterminate after reset Address: $0029 Read: Write: T1CH1H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $02A Read: Write: Reset: T1CH1L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Indeterminate after reset Figure 17-10. TIM1 Channel Registers (T1CH0H/L:T1CH1H/L) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 240 Freescale Semiconductor Chapter 18 Timer Interface Module (TIM2) 18.1 Introduction This section describes the timer interface module (TIM2). The TIM2 is a 6-channel timer that provides a timing reference with input capture, output compare, and pulse-width-modulation functions. Figure 18-2 is a block diagram of the TIM2. 18.2 Features Features of the TIM2 include: * Six input capture/output compare channels: - Rising-edge, falling-edge, or any-edge input capture trigger - Set, clear, or toggle output compare action * Buffered and unbuffered pulse width modulation (PWM) signal generation * Programmable TIM2 clock input - 7-frequency internal bus clock prescaler selection - External TIM2 clock input (4-MHz maximum frequency) * Free-running or modulo up-count operation * Toggle any channel pin on overflow * TIM2 counter stop and reset bits 18.3 Functional Description Figure 18-2 shows the TIM2 structure. The central component of the TIM2 is the 16-bit TIM2 counter that can operate as a free-running counter or a modulo up-counter. The TIM2 counter provides the timing reference for the input capture and output compare functions. The TIM2 counter modulo registers, T2MODH:T2MODL, control the modulo value of the TIM2 counter. Software can read the TIM2 counter value at any time without affecting the counting sequence. The six TIM2 channels are programmable independently as input capture or output compare channels. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 241 Timer Interface Module (TIM2) INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 18-1. Block Diagram Highlighting TIM2 Block and Pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 242 Freescale Semiconductor Functional Description TCLK PTD6/T2CH0 INTERNAL BUS CLOCK PRESCALER SELECT PRESCALER TSTOP PS2 TRST PS1 PS0 16-BIT COUNTER TOF TOIE INTERRUPT LOGIC 16-BIT COMPARATOR T2MODH:T2MODL CHANNEL 0 ELS0B ELS0A TOV0 CH0MAX 16-BIT COMPARATOR T2CH0H:T2CH0L CH0F 16-BIT LATCH MS0A CHANNEL 1 ELS1B ELS1A TOV1 CH1MAX 16-BIT COMPARATOR T2CH1H:T2CH1L CH0IE MS0B CH1F 16-BIT LATCH CH1IE MS1A CHANNEL 2 ELS2B ELS2A TOV2 CH2MAX 16-BIT COMPARATOR T2CH2H:T2CH2L CH2F 16-BIT LATCH MS2A CHANNEL 3 ELS3B ELS3A TOV3 CH3MAX 16-BIT COMPARATOR T2CH3H:T2CH3L CH2IE MS2B CH3F 16-BIT LATCH CH3IE MS3A CHANNEL 4 ELS4B ELS4A TOV4 CH4MAX 16-BIT COMPARATOR T2CH4H:T2CH4L CH4F 16-BIT LATCH MS4A CHANNEL 5 ELS5B ELS5A TOV5 CH5MAX 16-BIT COMPARATOR T2CH5H:T2CH5L CH4IE MS4B CH5F 16-BIT LATCH MS5A CH5IE PTD6 LOGIC T2CH0 INTERRUPT LOGIC PTD7 LOGIC T2CH1 INTERRUPT LOGIC PTF4 LOGIC T2CH2 INTERRUPT LOGIC PTF5 LOGIG T2CH3 INTERRUPT LOGIC PTF6 LOGIC T2CH4 INTERRUPT LOGIC PTF7 LOGIC T2CH5 INTERRUPT LOGIC Figure 18-2. TIM2 Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 243 Timer Interface Module (TIM2) Addr. Register Name Bit 7 TOF $002B TIM2 Status and Control Read: Register (T2SC) Write: See page 252. Reset: $002C $002D 1 Bit 0 PS2 PS1 PS0 1 0 0 0 0 0 TIM2 Counter Register High Read: (T2CNTH) Write: See page 254. Reset: Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 TIM2 Counter Register Low Read: (T2CNTL) Write: See page 254. Reset: Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 Bit 0 1 1 1 1 1 1 1 1 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 TIM2 Channel 0 Status and Read: Control Register (T2SC0) Write: See page 255. Reset: TIM2 Channel 0 Register High Read: (T2CH0H) Write: See page 258. Reset: $0032 TIM2 Channel 0 Register Low Read: (T2CH0L) Write: See page 258. Reset: $0033 TIM2 Channel 1 Status and Read: Control Register (T2SC1) Write: See page 255. Reset: $0456 2 0 $002F $0035 3 0 0 TIM2 Modulo Register Low Read: (T2MODL) Write: See page 254. Reset: $0034 4 0 TSTOP $002E $0031 5 TOIE TIM2 Modulo Register High Read: (T2MODH) Write: See page 254. Reset: $0030 6 TIM2 Channel 1 Register High Read: (T2CH1H) Write: See page 258. Reset: TIM2 Channel 1 Register Low Read: (T2CH1L) Write: See page 258. Reset: TIM2 Channel 2 Status and Read: Control Register (T2SC2) Write: See page 255. Reset: 0 CH0F 0 TRST Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH1F 0 CH1IE 0 MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH2F 0 0 CH2IE MS2B MS2A ELS2B ELS2A TOV2 CH2MAX 0 0 0 0 0 0 0 = Unimplemented Figure 18-3. TIM2 I/O Register Summary (Sheet 1 of 2) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 244 Freescale Semiconductor Functional Description Addr. $0457 $0458 $0459 Register Name TIM2 Channel 2 Register High Read: (T2CH2H) Write: See page 258. Reset: TIM2 Channel 2 Register Low Read: (T2CH2L) Write: See page 258. Reset: TIM2 Channel 3 Status and Read: Control Register (T2SC3) Write: See page 255. Reset: $045A TIM2 Channel 3 Register High Read: (T2CH3H) Write: See page 258. Reset: $045B TIM2 Channel 3 Register Low Read: (T2CH3L) Write: See page 258. Reset: $045C $045D TIM2 Channel 4 Status and Read: Control Register (T2SC4) Write: See page 255. Reset: TIM2 Channel 4 Register High Read: (T2CH4H) Write: See page 258. Reset: $045E TIM2 Channel 4 Register Low Read: (T2CH4L) Write: See page 258. Reset: $045F TIM2 Channel 5 Status and Read: Control Register (T2SC5) Write: See page 255. Reset: $0460 $0461 TIM2 Channel 5 Register High Read: (T2CH5H) Write: See page 258. Reset: TIM2 Channel 5 Register Low Read: (T2CH5L) Write: See page 258. Reset: Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH3F 0 CH3IE 0 MS3A ELS3B ELS3A TOV3 CH3MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH4F CH4IE MS4B MS4A ELS4B ELS4A TOV4 CH4MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset CH5F 0 CH5IE 0 MS5A ELS5B ELS5A TOV5 CH5MAX 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 2 1 Bit 0 Indeterminate after reset Bit 7 6 5 4 3 Indeterminate after reset = Unimplemented Figure 18-3. TIM2 I/O Register Summary (Sheet 2 of 2) 18.3.1 TIM2 Counter Prescaler The TIM2 clock source can be one of the seven prescaler outputs or the TIM2 clock pin, T2CH0. The prescaler generates seven clock rates from the internal bus clock. The prescaler select bits, PS[2:0], in the TIM2 status and control register select the TIM2 clock source. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 245 Timer Interface Module (TIM2) 18.3.2 Input Capture An input capture function has three basic parts: edge select logic, an input capture latch, and a 16-bit counter. Two 8-bit registers, which make up the 16-bit input capture register, are used to latch the value of the free-running counter after the corresponding input capture edge detector senses a defined transition. The polarity of the active edge is programmable. The level transition which triggers the counter transfer is defined by the corresponding input edge bits (ELSxB and ELSxA in T2SC0 through T2SC5 control registers with x referring to the active channel number). When an active edge occurs on the pin of an input capture channel, the TIM2 latches the contents of the TIM2 counter into the TIM2 channel registers, T2CHxH:T2CHxL. Input captures can generate TIM2 CPU interrupt requests. Software can determine that an input capture event has occurred by enabling input capture interrupts or by polling the status flag bit. The free-running counter contents are transferred to the TIM2 channel registers (T2CHxH:T2CHxL) (see 18.8.5 TIM2 Channel Registers) on each proper signal transition regardless of whether the TIM2 channel flag (CH0F-CH5F in T2SC0-T2SC5 registers) is set or clear. When the status flag is set, a CPU interrupt is generated if enabled. The value of the count latched or "captured" is the time of the event. Because this value is stored in the input capture register when the actual event occurs, user software can respond to this event at a later time and determine the actual time of the event. However, this must be done prior to another input capture on the same pin; otherwise, the previous time value will be lost. By recording the times for successive edges on an incoming signal, software can determine the period and/or pulse width of the signal. To measure a period, two successive edges of the same polarity are captured. To measure a pulse width, two alternate polarity edges are captured. Software should track the overflows at the 16-bit module counter to extend its range. Another use for the input capture function is to establish a time reference. In this case, an input capture function is used in conjunction with an output compare function. For example, to activate an output signal a specified number of clock cycles after detecting an input event (edge), use the input capture function to record the time at which the edge occurred. A number corresponding to the desired delay is added to this captured value and stored to an output compare register (see 18.8.5 TIM2 Channel Registers). Because both input captures and output compares are referenced to the same 16-bit modulo counter, the delay can be controlled to the resolution of the counter independent of software latencies. Reset does not affect the contents of the input capture channel (T2CHxH:T2CHxL) registers. 18.3.3 Output Compare With the output compare function, the TIM2 can generate a periodic pulse with a programmable polarity, duration, and frequency. When the counter reaches the value in the registers of an output compare channel, the TIM2 can set, clear, or toggle the channel pin. Output compares can generate TIM2 CPU interrupt requests. 18.3.3.1 Unbuffered Output Compare Any output compare channel can generate unbuffered output compare pulses as described in 18.3.3 Output Compare. The pulses are unbuffered because changing the output compare value requires writing the new value over the old value currently in the TIM2 channel registers. An unsynchronized write to the TIM2 channel registers to change an output compare value could cause incorrect operation for up to two counter overflow periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that counter overflow period. Also, using a TIM2 overflow interrupt routine to write a new, smaller output MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 246 Freescale Semiconductor Functional Description compare value may cause the compare to be missed. The TIM2 may pass the new value before it is written. Use the following methods to synchronize unbuffered changes in the output compare value on channel x: * When changing to a smaller value, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current output compare pulse. The interrupt routine has until the end of the counter overflow period to write the new value. * When changing to a larger output compare value, enable TIM2 overflow interrupts and write the new value in the TIM2 overflow interrupt routine. The TIM2 overflow interrupt occurs at the end of the current counter overflow period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same counter overflow period. 18.3.3.2 Buffered Output Compare Channels 0 and 1 can be linked to form a buffered output compare channel whose output appears on the T2CH0 pin. The TIM2 channel registers of the linked pair alternately control the output. Setting the MS0B bit in TIM2 channel 0 status and control register (T2SC0) links channel 0 and channel 1. The output compare value in the TIM2 channel 0 registers initially controls the output on the T2CH0 pin. Writing to the TIM2 channel 1 registers enables the TIM2 channel 1 registers to synchronously control the output after the TIM2 overflows. At each subsequent overflow, the TIM2 channel registers (0 or 1) that control the output are the ones written to last. T2SC0 controls and monitors the buffered output compare function, and TIM2 channel 1 status and control register (T2SC1) is unused. While the MS0B bit is set, the channel 1 pin, T2CH1, is available as a general-purpose I/O pin. Channels 2 and 3 can be linked to form a buffered output compare channel whose output appears on the T2CH2 pin. The TIM2 channel registers of the linked pair alternately control the output. Setting the MS2B bit in TIM2 channel 2 status and control register (T2SC2) links channel 2 and channel 3. The output compare value in the TIM2 channel 2 registers initially controls the output on the T2CH2 pin. Writing to the TIM2 channel 3 registers enables the TIM2 channel 3 registers to synchronously control the output after the TIM2 overflows. At each subsequent overflow, the TIM2 channel registers (2 or 3) that control the output are the ones written to last. T2SC2 controls and monitors the buffered output compare function, and TIM2 channel 3 status and control register (T2SC3) is unused. While the MS2B bit is set, the channel 3 pin, T2CH3, is available as a general-purpose I/O pin. Channels 4 and 5 can be linked to form a buffered output compare channel whose output appears on the T2CH4 pin. The TIM2 channel registers of the linked pair alternately control the output. Setting the MS4B bit in TIM2 channel 4 status and control register (T2SC4) links channel 4 and channel 5. The output compare value in the TIM2 channel 4 registers initially controls the output on the T2CH4 pin. Writing to the TIM2 channel 5 registers enables the TIM2 channel 5 registers to synchronously control the output after the TIM2 overflows. At each subsequent overflow, the TIM2 channel registers (4 or 5) that control the output are the ones written to last. T2SC4 controls and monitors the buffered output compare function, and TIM2 channel 5 status and control register (T2SC5) is unused. While the MS4B bit is set, the channel 5 pin, T2CH5, is available as a general-purpose I/O pin. NOTE In buffered output compare operation, do not write new output compare values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 247 Timer Interface Module (TIM2) channel. Writing to the active channel registers is the same as generating unbuffered output compares. 18.3.4 Pulse Width Modulation (PWM) By using the toggle-on-overflow feature with an output compare channel, the TIM2 can generate a PWM signal. The value in the TIM2 counter modulo registers determines the period of the PWM signal. The channel pin toggles when the counter reaches the value in the TIM2 counter modulo registers. The time between overflows is the period of the PWM signal. As Figure 18-4 shows, the output compare value in the TIM2 channel registers determines the pulse width of the PWM signal. The time between overflow and output compare is the pulse width. Program the TIM2 to clear the channel pin on output compare if the polarity of the PWM pulse is 1 (ELSxA = 0). Program the TIM2 to set the pin if the polarity of the PWM pulse is 0 (ELSxA = 1). OVERFLOW OVERFLOW OVERFLOW PERIOD POLARITY = 1 (ELSxA = 0) TCHx PULSE WIDTH POLARITY = 0 (ELSxA = 1) TCHx OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 18-4. PWM Period and Pulse Width The value in the TIM2 counter modulo registers and the selected prescaler output determines the frequency of the PWM output. The frequency of an 8-bit PWM signal is variable in 256 increments. Writing $00FF (255) to the TIM2 counter modulo registers produces a PWM period of 256 times the internal bus clock period if the prescaler select value is 000 (see 18.8.1 TIM2 Status and Control Register). The value in the TIM2 channel registers determines the pulse width of the PWM output. The pulse width of an 8-bit PWM signal is variable in 256 increments. Writing $0080 (128) to the TIM2 channel registers produces a duty cycle of 128/256 or 50%. 18.3.4.1 Unbuffered PWM Signal Generation Any output compare channel can generate unbuffered PWM pulses as described in 18.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because changing the pulse width requires writing the new pulse width value over the value currently in the TIM2 channel registers. An unsynchronized write to the TIM2 channel registers to change a pulse width value could cause incorrect operation for up to two PWM periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that PWM period. Also, using a TIM2 overflow interrupt routine to write a new, smaller pulse width value may cause the compare to be missed. The TIM2 may pass the new value before it is written to the timer channel (T2CHxH:T2CHxL) registers. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 248 Freescale Semiconductor Functional Description Use the following methods to synchronize unbuffered changes in the PWM pulse width on channel x: * When changing to a shorter pulse width, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current pulse. The interrupt routine has until the end of the PWM period to write the new value. * When changing to a longer pulse width, enable TIM2 overflow interrupts and write the new value in the TIM2 overflow interrupt routine. The TIM2 overflow interrupt occurs at the end of the current PWM period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same PWM period. NOTE In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare also can cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 18.3.4.2 Buffered PWM Signal Generation Channels 0 and 1 can be linked to form a buffered PWM channel whose output appears on the T2CH0 pin. The TIM2 channel registers of the linked pair alternately control the pulse width of the output. Setting the MS0B bit in TIM2 channel 0 status and control register (T2SC0) links channel 0 and channel 1. The TIM2 channel 0 registers initially control the pulse width on the T2CH0 pin. Writing to the TIM2 channel 1 registers enables the TIM2 channel 1 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIM2 channel registers (0 or 1) that control the pulse width are the ones written to last. T2SC0 controls and monitors the buffered PWM function, and TIM2 channel 1 status and control register (T2SC1) is unused. While the MS0B bit is set, the channel 1 pin, T2CH1, is available as a general-purpose I/O pin. Channels 2 and 3 can be linked to form a buffered PWM channel whose output appears on the T2CH2 pin. The TIM2 channel registers of the linked pair alternately control the pulse width of the output. Setting the MS2B bit in TIM2 channel 2 status and control register (T2SC2) links channel 2 and channel 3. The TIM2 channel 2 registers initially control the pulse width on the T2CH2 pin. Writing to the TIM2 channel 3 registers enables the TIM2 channel 3 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIM2 channel registers (2 or 3) that control the pulse width are the ones written to last. T2SC2 controls and monitors the buffered PWM function, and TIM2 channel 3 status and control register (T2SC3) is unused. While the MS2B bit is set, the channel 3 pin, T2CH3, is available as a general-purpose I/O pin. Channels 4 and 5 can be linked to form a buffered PWM channel whose output appears on the T2CH4 pin. The TIM2 channel registers of the linked pair alternately control the pulse width of the output. Setting the MS4B bit in TIM2 channel 4 status and control register (T2SC4) links channel 4 and channel 5. The TIM2 channel 4 registers initially control the pulse width on the T2CH4 pin. Writing to the TIM2 channel 5 registers enables the TIM2 channel 5 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIM2 channel registers (4 or 5) that control the pulse width are the ones written to last. T2SC4 controls and monitors the buffered PWM function, and TIM2 channel 5 status and control register (T2SC5) is unused. While the MS4B bit is set, the channel 5 pin, T2CH5, is available as a general-purpose I/O pin. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 249 Timer Interface Module (TIM2) NOTE In buffered PWM signal generation, do not write pulse width values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered PWM signals. 18.3.4.3 PWM Initialization To ensure correct operation when generating unbuffered or buffered PWM signals, use the following initialization procedure: 1. In the TIM2 status and control register (T2SC): a. Stop the TIM2 counter by setting the TIM2 stop bit, TSTOP. b. Reset the TIM2 counter and prescaler by setting the TIM2 reset bit, TRST. 2. In the TIM2 counter modulo registers (T2MODH:T2MODL), write the value for the required PWM period. 3. In the TIM2 channel x registers (T2CHxH:T2CHxL), write the value for the required pulse width. 4. In TIM2 channel x status and control register (T2SCx): a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for buffered output compare or PWM signals) to the mode select bits, MSxB:MSxA. (See Table 18-2.) b. Write 1 to the toggle-on-overflow bit, TOVx. c. Write 1:0 (polarity 1 -- to clear output on compare) or 1:1 (polarity 0 -- to set output on compare) to the edge/level select bits, ELSxB:ELSxA. The output action on compare must force the output to the complement of the pulse width level. (See Table 18-2.) NOTE In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare can also cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 5. In the TIM2 status control register (T2SC), clear the TIM2 stop bit, TSTOP. Setting MS0B links channels 0 and 1 and configures them for buffered PWM operation. The TIM2 channel 0 registers (T2CH0H:T2CH0L) initially control the buffered PWM output. TIM2 status control register 0 (T2SC0) controls and monitors the PWM signal from the linked channels. MS0B takes priority over MS0A. Setting MS2B links channels 2 and 3 and configures them for buffered PWM operation. The TIM2 channel 2 registers (T2CH2H:T2CH2L) initially control the buffered PWM output. TIM2 status control register 2 (T2SC2) controls and monitors the PWM signal from the linked channels. MS2B takes priority over MS2A. Setting MS4B links channels 4 and 5 and configures them for buffered PWM operation. The TIM2 channel 4 registers (T2CH4H:T2CH4L) initially control the buffered PWM output. TIM2 status control register 4 (T2SC4) controls and monitors the PWM signal from the linked channels. MS4B takes priority over MS4A. Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM2 overflows. Subsequent output compares try to force the output to a state it is already in and have no effect. The result is a 0% duty cycle output. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 250 Freescale Semiconductor Interrupts Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit generates a 100% duty cycle output. (See 18.8.4 TIM2 Channel Status and Control Registers.) 18.4 Interrupts The following TIM2 sources can generate interrupt requests: * TIM2 overflow flag (TOF) -- The TOF bit is set when the TIM2 counter reaches the modulo value programmed in the TIM2 counter modulo registers. The TIM2 overflow interrupt enable bit, TOIE, enables TIM2 overflow interrupt requests. TOF and TOIE are in the TIM2 status and control register. * TIM2 channel flags (CH5F:CH0F) -- The CHxF bit is set when an input capture or output compare occurs on channel x. Channel x TIM2 CPU interrupt requests are controlled by the channel x interrupt enable bit, CHxIE. 18.5 Low-Power Modes The WAIT and STOP instructions put the MCU in low-power standby modes. 18.5.1 Wait Mode The TIM2 remains active after the execution of a WAIT instruction. In wait mode, the TIM2 registers are not accessible by the CPU. Any enabled CPU interrupt request from the TIM2 can bring the MCU out of wait mode. If TIM2 functions are not required during wait mode, reduce power consumption by stopping the TIM2 before executing the WAIT instruction. 18.5.2 Stop Mode The TIM2 is inactive after the execution of a STOP instruction. The STOP instruction does not affect register conditions or the state of the TIM2 counter. TIM2 operation resumes when the MCU exits stop mode. 18.6 TIM2 During Break Interrupts A break interrupt stops the TIM2 counter and inhibits input captures. The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear status bits during the break state. (See 14.7.3 Break Flag Control Register.) To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a 2-step read/write clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 251 Timer Interface Module (TIM2) 18.7 I/O Signals Port D shares two of its pins with the TIM2. Port F shares four of its pins with the TIM2. PTD6/T2CH0 is an external clock input to the TIM2 prescaler. The six TIM2 channel I/O pins are PTD6/T2CH0, PTD7/T2CH1, PTF4/T2CH2, PTF5/T2CH3, PTF6/T2CH4, and PTF7/T2CH5. 18.7.1 TIM2 Clock Pin (T2CH0) T2CH0 is an external clock input that can be the clock source for the TIM2 counter instead of the prescaled internal bus clock. Select the T2CH0 input by writing 1s to the three prescaler select bits, PS[2:0]. (See 18.8.1 TIM2 Status and Control Register.) The minimum TCLK pulse width is specified in 20.14 Timer Interface Module Characteristics. The maximum TCLK frequency is the least: 4 MHz or bus frequency / 2. When the PTD6/T2CH0 pin is the TIM2 clock input, it is an input regardless of the state of the DDRD6 bit in data direction register D. 18.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0) Each channel I/O pin is programmable independently as an input capture pin or an output compare pin. T2CH0, T2CH2, and T2CH4 can be configured as buffered output compare or buffered PWM pins. 18.8 I/O Registers These I/O registers control and monitor TIM2 operation: * TIM2 status and control register (T2SC) * TIM2 counter registers (T2CNTH:T2CNTL) * TIM2 counter modulo registers (T2MODH:T2MODL) * TIM2 channel status and control registers (T2SC0, T2SC1, T2SC2, T2SC3, T2SC4, and T2SC5) * TIM2 channel registers (T2CH0H:T2CH0L, T2CH1H:T2CH1L, T2CH2H:T2CH2L, T2CH3H:T2CH3L, T2CH4H:T2CH4L, and T2CH5H:T2CH5L) 18.8.1 TIM2 Status and Control Register The TIM2 status and control register: * Enables TIM2 overflow interrupts * Flags TIM2 overflows * Stops the TIM2 counter * Resets the TIM2 counter * Prescales the TIM2 counter clock Address: $002B Bit 7 Read: TOF Write: 0 Reset: 0 6 5 TOIE TSTOP 0 1 4 3 0 0 TRST 0 0 2 1 Bit 0 PS2 PS1 PS0 0 0 0 = Unimplemented Figure 18-5. TIM2 Status and Control Register (T2SC) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 252 Freescale Semiconductor I/O Registers TOF -- TIM2 Overflow Flag Bit This read/write flag is set when the TIM2 counter resets reaches the modulo value programmed in the TIM2 counter modulo registers. Clear TOF by reading the TIM2 status and control register when TOF is set and then writing a 0 to TOF. If another TIM2 overflow occurs before the clearing sequence is complete, then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF has no effect. 1 = TIM2 counter has reached modulo value 0 = TIM2 counter has not reached modulo value TOIE -- TIM2 Overflow Interrupt Enable Bit This read/write bit enables TIM2 overflow interrupts when the TOF bit becomes set. Reset clears the TOIE bit. 1 = TIM2 overflow interrupts enabled 0 = TIM2 overflow interrupts disabled TSTOP -- TIM2 Stop Bit This read/write bit stops the TIM2 counter. Counting resumes when TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIM2 counter until software clears the TSTOP bit. 1 = TIM2 counter stopped 0 = TIM2 counter active NOTE Do not set the TSTOP bit before entering wait mode if the TIM2 is required to exit wait mode. Also when the TSTOP bit is set and the timer is configured for input capture operation, input captures are inhibited until the TSTOP bit is cleared. TRST -- TIM2 Reset Bit Setting this write-only bit resets the TIM2 counter and the TIM2 prescaler. Setting TRST has no effect on any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIM2 counter is reset and always reads as 0. Reset clears the TRST bit. 1 = Prescaler and TIM2 counter cleared 0 = No effect NOTE Setting the TSTOP and TRST bits simultaneously stops the TIM2 counter at a value of $0000. PS[2:0] -- Prescaler Select Bits These read/write bits select either the T2CH0 pin or one of the seven prescaler outputs as the input to the TIM2 counter as Table 18-1 shows. Reset clears the PS[2:0] bits. Table 18-1. Prescaler Selection PS[2:0] TIM2 Clock Source 000 Internal bus clock /1 001 Internal bus clock / 2 010 Internal bus clock / 4 011 Internal bus clock / 8 100 Internal bus clock / 16 101 Internal bus clock / 32 110 Internal bus clock / 64 111 T2CH0 MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 253 Timer Interface Module (TIM2) 18.8.2 TIM2 Counter Registers The two read-only TIM2 counter registers contain the high and low bytes of the value in the TIM2 counter. Reading the high byte (T2CNTH) latches the contents of the low byte (T2CNTL) into a buffer. Subsequent reads of T2CNTH do not affect the latched T2CNTL value until T2CNTL is read. Reset clears the TIM2 counter registers. Setting the TIM2 reset bit (TRST) also clears the TIM2 counter registers. NOTE If T2CNTH is read during a break interrupt, be sure to unlatch T2CNTL by reading T2CNTL before exiting the break interrupt. Otherwise, T2CNTL retains the value latched during the break. Address: $002C Read: T2CNTH Bit 7 6 5 4 3 2 1 Bit 0 BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 0 0 0 0 0 0 0 0 Write: Reset: Address: $002D Read: T2CNTL Bit 7 6 5 4 3 2 1 Bit 0 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 0 0 0 0 0 0 0 0 Write: Reset: = Unimplemented Figure 18-6. TIM2 Counter Registers (T2CNTH and T2CNTL) 18.8.3 TIM2 Counter Modulo Registers The read/write TIM2 modulo registers contain the modulo value for the TIM2 counter. When the TIM2 counter reaches the modulo value, the overflow flag (TOF) becomes set, and the TIM2 counter resumes counting from $0000 at the next timer clock. Writing to the high byte (T2MODH) inhibits the TOF bit and overflow interrupts until the low byte (T2MODL) is written. Reset sets the TIM2 counter modulo registers. Address: $002E Read: Write: Reset: 6 5 4 3 2 1 Bit 0 BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 1 1 1 1 1 1 1 1 Address: $002F Read: Write: Reset: T2MODH Bit 7 T2MODL Bit 7 6 5 4 3 2 1 Bit 0 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 1 1 1 1 1 1 1 1 Figure 18-7. TIM2 Counter Modulo Registers (T2MODH and T2MODL) NOTE Reset the TIM2 counter before writing to the TIM2 counter modulo registers. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 254 Freescale Semiconductor I/O Registers 18.8.4 TIM2 Channel Status and Control Registers Each of the TIM2 channel status and control registers: * Flags input captures and output compares * Enables input capture and output compare interrupts * Selects input capture, output compare, or PWM operation * Selects high, low, or toggling output on output compare * Selects rising edge, falling edge, or any edge as the active input capture trigger * Selects output toggling on TIM2 overflow * Selects 0% and 100% PWM duty cycle * Selects buffered or unbuffered output compare/PWM operation Address: $0030 Bit 7 T2SC0 6 Read: CH0F Write: 0 Reset: 5 4 3 2 1 Bit 0 CH0IE MS0B MS0A ELS0B ELS0A TOV0 CH0MAX 0 0 0 0 0 0 0 0 Address: $0033 T2SC1 5 4 3 2 1 Bit 0 MS1A ELS1B ELS1A TOV1 CH1MAX 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 CH2IE MS2B MS2A ELS2B ELS2A TOV2 CH2MAX 0 0 0 0 0 0 5 4 3 2 1 Bit 0 MS3A ELS3B ELS3A TOV3 CH3MAX 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 CH4IE MS4B MS4A ELS4B ELS4A TOV4 CH4MAX 0 0 0 0 0 0 5 4 3 2 1 Bit 0 MS5A ELS5B ELS5A TOV5 CH5MAX 0 0 0 0 0 Bit 7 6 Read: CH1F Write: 0 Reset: 0 0 Address: $0456 T2SC2 Bit 7 CH1IE Read: CH2F Write: 0 Reset: 0 0 Address: $0459 T2SC3 Bit 7 6 Read: CH3F Write: 0 Reset: 0 0 Address: $045C T2SC4 Bit 7 CH4F Write: 0 Reset: 0 0 Address: $045F T2SC5 Bit 7 CH5F Write: 0 Reset: 0 0 CH3IE Read: Read: 0 6 CH5IE 0 0 0 = Unimplemented Figure 18-8. TIM2 Channel Status and Control Registers (T2SC0:T2SC5) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 255 Timer Interface Module (TIM2) CHxF -- Channel x Flag Bit When channel x is an input capture channel, this read/write bit is set when an active edge occurs on the channel x pin. When channel x is an output compare channel, CHxF is set when the value in the TIM2 counter registers matches the value in the TIM2 channel x registers. When CHxIE = 1, clear CHxF by reading TIM2 channel x status and control register with CHxF set, and then writing a 0 to CHxF. If another interrupt request occurs before the clearing sequence is complete, then writing 0 to CHxF has no effect. Therefore, an interrupt request cannot be lost due to inadvertent clearing of CHxF. Reset clears the CHxF bit. Writing a 1 to CHxF has no effect. 1 = Input capture or output compare on channel x 0 = No input capture or output compare on channel x CHxIE -- Channel x Interrupt Enable Bit This read/write bit enables TIM2 CPU interrupts on channel x. Reset clears the CHxIE bit. 1 = Channel x CPU interrupt requests enabled 0 = Channel x CPU interrupt requests disabled MSxB -- Mode Select Bit B This read/write bit selects buffered output compare/PWM operation. MSxB exists only in the TIM2 channel 0, TIM2 channel 2, and TIM2 channel 4 status and control registers. Setting MS0B disables the channel 1 status and control register and reverts T2CH1 pin to general-purpose I/O. Setting MS2B disables the channel 3 status and control register and reverts T2CH3 pin to general-purpose I/O. Setting MS4B disables the channel 5 status and control register and reverts T2CH5 pin to general-purpose I/O. Reset clears the MSxB bit. 1 = Buffered output compare/PWM operation enabled 0 = Buffered output compare/PWM operation disabled MSxA -- Mode Select Bit A When ELSxB:ELSxA 00, this read/write bit selects either input capture operation or unbuffered output compare/PWM operation. (See Table 18-2.) 1 = Unbuffered output compare/PWM operation 0 = Input capture operation When ELSxB:ELSxA = 00, this read/write bit selects the initial output level of the T2CHx pin once PWM, input capture, or output compare operation is enabled. (See Table 18-2.) Reset clears the MSxA bit. 1 = Initial output level low 0 = Initial output level high NOTE Before changing a channel function by writing to the MSxB or MSxA bit, set the TSTOP and TRST bits in the TIM2 status and control register (T2SC). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 256 Freescale Semiconductor I/O Registers Table 18-2. Mode, Edge, and Level Selection MSxB MSxA ELSxB ELSxA X 0 0 0 Mode Output preset Configuration Pin under port control; initial output level high X 1 0 0 Pin under port control; initial output level low 0 0 0 1 Capture on rising edge only 0 0 1 0 0 0 1 1 Capture on rising or falling edge 0 1 0 0 Software compare only 0 1 0 1 0 1 1 0 0 1 1 1 1 X 0 1 1 X 1 0 1 X 1 1 Input capture Output compare or PWM Capture on falling edge only Toggle output on compare Clear output on compare Set output on compare Buffered output compare or buffered PWM Toggle output on compare Clear output on compare Set output on compare ELSxB and ELSxA -- Edge/Level Select Bits When channel x is an input capture channel, these read/write bits control the active edge-sensing logic on channel x. When channel x is an output compare channel, ELSxB and ELSxA control the channel x output behavior when an output compare occurs. When ELSxB and ELSxA are both clear, channel x is not connected to port D or port F, and pin PTDx/T2CHx or pin PTFx/T2CHx is available as a general- purpose I/O pin. Table 18-2 shows how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits. NOTE After initially enabling a TIM2 channel register for input capture operation and selecting the edge sensitivity, clear CHxF to ignore any erroneous edge detection flags. TOVx -- Toggle-On-Overflow Bit When channel x is an output compare channel, this read/write bit controls the behavior of the channel x output when the TIM2 counter overflows. When channel x is an input capture channel, TOVx has no effect. Reset clears the TOVx bit. 1 = Channel x pin toggles on TIM2 counter overflow. 0 = Channel x pin does not toggle on TIM2 counter overflow. NOTE When TOVx is set, a TIM2 counter overflow takes precedence over a channel x output compare if both occur at the same time. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 257 Timer Interface Module (TIM2) CHxMAX -- Channel x Maximum Duty Cycle Bit When the TOVx bit is at a 1 and clear output on compare is selected, setting the CHxMAX bit forces the duty cycle of buffered and unbuffered PWM signals to 100%. As Figure 18-9 shows, the CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays at 100% duty cycle level until the cycle after CHxMAX is cleared. NOTE The 100% PWM duty cycle is defined as a continuous high level if the PWM polarity is 1 and a continuous low level if the PWM polarity is 0. Conversely, a 0% PWM duty cycle is defined as a continuous low level if the PWM polarity is 1 and a continuous high level if the PWM polarity is 0. OVERFLOW OVERFLOW OVERFLOW OVERFLOW OVERFLOW PERIOD PTDx/T2CHx OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE CHxMAX Figure 18-9. CHxMAX Latency 18.8.5 TIM2 Channel Registers These read/write registers contain the captured TIM2 counter value of the input capture function or the output compare value of the output compare function. The state of the TIM2 channel registers after reset is unknown. In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the TIM2 channel x registers (T2CHxH) inhibits input captures until the low byte (T2CHxL) is read. In output compare mode (MSxB:MSxA 0:0), writing to the high byte of the TIM2 channel x registers (T2CHxH) inhibits output compares until the low byte (T2CHxL) is written. Address: $0031 Read: Write: T2CH0H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $0032 Read: Write: Reset: T2CH0L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Indeterminate after reset Figure 18-10. TIM2 Channel Registers (T2CH0H/L:T2CH5H/L) (Sheet 1 of 3) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 258 Freescale Semiconductor I/O Registers Address: $0034 Read: Write: T2CH1H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $0035 Read: Write: T2CH1L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset: Indeterminate after reset Address: $0457 Read: Write: T2CH2H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $0458 Read: Write: T2CH2L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset: Indeterminate after reset Address: $045A Read: Write: T2CH3H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $045B Read: Write: T2CH3L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset: Indeterminate after reset Address: $045D Read: Write: T2CH4H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $045E Read: Write: Reset: T2CH4L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Indeterminate after reset Figure 18-10. TIM2 Channel Registers (T2CH0H/L:T2CH5H/L) (Sheet 2 of 3) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 259 Timer Interface Module (TIM2) Address: $0460 Read: Write: T2CH5H Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Reset: Indeterminate after reset Address: $0461 Read: Write: Reset: T2CH5L Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Indeterminate after reset Figure 18-10. TIM2 Channel Registers (T2CH0H/L:T2CH5H/L) (Sheet 3 of 3) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 260 Freescale Semiconductor Chapter 19 Development Support 19.1 Introduction This section describes the break module, the monitor module (MON), and the monitor mode entry methods. 19.2 Break Module (BRK) The break module can generate a break interrupt that stops normal program flow at a defined address to enter a background program. Features of the break module include: * Accessible input/output (I/O) registers during the break Interrupt * Central processor unit (CPU) generated break interrupts * Software-generated break interrupts * Computer operating properly (COP) disabling during break interrupts 19.2.1 Functional Description When the internal address bus matches the value written in the break address registers, the break module issues a breakpoint signal (BKPT) to the system integration module (SIM). The SIM then causes the CPU to load the instruction register with a software interrupt instruction (SWI). The program counter vectors to $FFFC and $FFFD ($FEFC and $FEFD in monitor mode). The following events can cause a break interrupt to occur: * A CPU generated address (the address in the program counter) matches the contents of the break address registers. * Software writes a 1 to the BRKA bit in the break status and control register. When a CPU generated address matches the contents of the break address registers, the break interrupt is generated. A return-from-interrupt instruction (RTI) in the break routine ends the break interrupt and returns the microcontroller unit (MCU) to normal operation. Figure 19-2 shows the structure of the break module. Figure 19-3 provides a summary of the I/O registers. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 261 Development Support INTERNAL BUS MONITOR ROM 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 2048 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 62,078 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure 19-1. Block Diagram Highlighting BRK and MON Blocks MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 262 Freescale Semiconductor Break Module (BRK) ADDRESS BUS[15:8] BREAK ADDRESS REGISTER HIGH 8-BIT COMPARATOR ADDRESS BUS[15:0] BKPT (TO SIM) CONTROL 8-BIT COMPARATOR BREAK ADDRESS REGISTER LOW ADDRESS BUS[7:0] Figure 19-2. Break Module Block Diagram Addr. Register Name $FE00 Read: Break Status Register (BSR) Write: See page 266. Reset: $FE03 $FE09 $FE0A $FE0B Read: Break Flag Control Register (BFCR) Write: See page 266. Reset: Read: Break Address High Register (BRKH) Write: See page 265. Reset: Read: Break Address Low Register (BRKL) Write: See page 265. Reset: Read: Break Status and Control Register (BRKSCR) Write: See page 265. Reset: 1. Writing a 0 clears SBSW. Bit 7 6 5 4 3 2 R R R R R R 1 SBSW Note(1) Bit 0 R 0 BCFE R R R R R R R Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 BRKE BRKA 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R = Reserved 0 = Unimplemented Figure 19-3. Break I/O Register Summary MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 263 Development Support When the internal address bus matches the value written in the break address registers or when software writes a 1 to the BRKA bit in the break status and control register, the CPU starts a break interrupt by: * Loading the instruction register with the SWI instruction * Loading the program counter with $FFFC and $FFFD ($FEFC and $FEFD in monitor mode) The break interrupt timing is: * When a break address is placed at the address of the instruction opcode, the instruction is not executed until after completion of the break interrupt routine. * When a break address is placed at an address of an instruction operand, the instruction is executed before the break interrupt. * When software writes a 1 to the BRKA bit, the break interrupt occurs just before the next instruction is executed. By updating a break address and clearing the BRKA bit in a break interrupt routine, a break interrupt can be generated continuously. CAUTION A break address should be placed at the address of the instruction opcode. When software does not change the break address and clears the BRKA bit in the first break interrupt routine, the next break interrupt will not be generated after exiting the interrupt routine even when the internal address bus matches the value written in the break address registers. 19.2.1.1 Flag Protection During Break Interrupts The system integration module (SIM) controls whether or not module status bits can be cleared during the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status bits during the break state. See 14.7.3 Break Flag Control Register and the Break Interrupts subsection for each module. 19.2.1.2 TIM During Break Interrupts A break interrupt stops the timer counter and inhibits input captures. 19.2.1.3 COP During Break Interrupts The COP is disabled during a break interrupt when VTST is present on the RST pin. 19.2.2 Break Module Registers These registers control and monitor operation of the break module: * Break status and control register (BRKSCR) * Break address register high (BRKH) * Break address register low (BRKL) * Break status register (BSR) * Break flag control register (BFCR) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 264 Freescale Semiconductor Break Module (BRK) 19.2.2.1 Break Status and Control Register The break status and control register (BRKSCR) contains break module enable and status bits. Address: $FE0B Read: Write: Reset: Bit 7 6 BRKE BRKA 0 0 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 = Unimplemented Figure 19-4. Break Status and Control Register (BRKSCR) BRKE -- Break Enable Bit This read/write bit enables breaks on break address register matches. Clear BRKE by writing a 0 to bit 7. Reset clears the BRKE bit. 1 = Breaks enabled on 16-bit address match 0 = Breaks disabled BRKA -- Break Active Bit This read/write status and control bit is set when a break address match occurs. Writing a 1 to BRKA generates a break interrupt. Clear BRKA by writing a 0 to it before exiting the break routine. Reset clears the BRKA bit. 1 = Break address match 0 = No break address match 19.2.2.2 Break Address Registers The break address registers (BRKH and BRKL) contain the high and low bytes of the desired breakpoint address. Reset clears the break address registers. Address: $FE09 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 19-5. Break Address Register High (BRKH) Address: $FE0A Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 19-6. Break Address Register Low (BRKL) MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 265 Development Support 19.2.2.3 Break Status Register The break status register (BSR) contains a flag to indicate that a break caused an exit from wait mode. This register is only used in emulation mode. Address: $FE00 Bit 7 Read: Write: R 6 R 5 R 4 R 3 R 2 R 1 SBSW Note(1) Reset: Bit 0 R 0 R = Reserved 1. Writing a 0 clears SBSW. Figure 19-7. Break Status Register (BSR) SBSW -- SIM Break Stop/Wait SBSW can be read within the break state SWI routine. The user can modify the return address on the stack by subtracting one from it. 1 = Wait mode was exited by break interrupt 0 = Wait mode was not exited by break interrupt 19.2.2.4 Break Flag Control Register The break control register (BFCR) contains a bit that enables software to clear status bits while the MCU is in a break state. Address: $FE03 Read: Write: Reset: Bit 7 6 5 4 3 2 1 Bit 0 BCFE R R R R R R R 0 = Reserved R Figure 19-8. Break Flag Control Register (BFCR) BCFE -- Break Clear Flag Enable Bit This read/write bit enables software to clear status bits by accessing status registers while the MCU is in a break state. To clear status bits during the break state, the BCFE bit must be set. 1 = Status bits clearable during break 0 = Status bits not clearable during break 19.2.3 Low-Power Modes The WAIT and STOP instructions put the MCU in low power- consumption standby modes. If enabled, the break module will remain enabled in wait and stop modes. However, since the internal address bus does not increment in these modes, a break interrupt will never be triggered. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 266 Freescale Semiconductor Monitor Module (MON) 19.3 Monitor Module (MON) The monitor module allows debugging and programming of the microcontroller unit (MCU) through a single-wire interface with a host computer. Monitor mode entry can be achieved without use of the higher test voltage, VTST, as long as vector addresses $FFFE and $FFFF are blank, thus reducing the hardware requirements for in-circuit programming. Features of the monitor module include: * Normal user-mode pin functionality * One pin dedicated to serial communication between MCU and host computer * Standard non-return-to-zero (NRZ) communication with host computer * Standard communication baud rate (7200 @ 2-MHz bus frequency) * Execution of code in random-access memory (RAM) or FLASH * FLASH memory security feature(1) * FLASH memory programming interface * Monitor mode entry without high voltage, VTST, if reset vector is blank ($FFFE and $FFFF contain $FF) * Normal monitor mode entry if VTST is applied to IRQ 19.3.1 Functional Description Figure 19-9 shows a simplified diagram of the monitor mode. The monitor module receives and executes commands from a host computer. Figure 19-10 and Figure 19-11 show example circuits used to enter monitor mode and communicate with a host computer via a standard RS-232 interface. Simple monitor commands can access any memory address. In monitor mode, the MCU can execute code downloaded into RAM by a host computer while most MCU pins retain normal operating mode functions. All communication between the host computer and the MCU is through the PTA0 pin. A level-shifting and multiplexing interface is required between PTA0 and the host computer. PTA0 is used in a wired-OR configuration and requires a pullup resistor. Table 19-1 shows the pin conditions for entering monitor mode. As specified in the table, monitor mode may be entered after a power-on reset (POR) and will allow communication at 7200 baud provided one of the following sets of conditions is met: * If $FFFE and $FFFF does not contain $FF (programmed state): - The external clock is 4.0 MHz (7200 baud) - PTB4 = low - IRQ = VTST * If $FFFE and $FFFF do not contain $FF (programmed state): - The external clock is 8.0 MHz (7200 baud) - PTB4 = high - IRQ = VTST * If $FFFE and $FFFF contain $FF (erased state): - The external clock is 8.0 MHz (7200 baud) - IRQ = VDD (this can be implemented through the internal IRQ pullup) or VSS 1. No security feature is absolutely secure. However, Freescale's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 267 Development Support POR RESET NO CONDITIONS FROM Table 19-1 PTA0 = 1, PTA1 = 0, RESET VECTOR BLANK? IRQ = VTST? YES PTA0 = 1, PTA1 = 0, PTB0 = 1, AND PTB1 = 0? NO NO YES YES FORCED MONITOR MODE NORMAL USER MODE NORMAL MONITOR MODE INVALID USER MODE HOST SENDS 8 SECURITY BYTES IS RESET POR? YES NO YES ARE ALL SECURITY BYTES CORRECT? ENABLE FLASH NO DISABLE FLASH MONITOR MODE ENTRY DEBUGGING AND FLASH PROGRAMMING (IF FLASH IS ENABLED) EXECUTE MONITOR CODE YES DOES RESET OCCUR? NO Figure 19-9. Simplified Monitor Mode Entry Flowchart MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 268 Freescale Semiconductor Monitor Module (MON) MC68HC908GR60A N.C. VDD RST 27 pF 1 1 F + 3 4 1 F + VDD VCC 16 C1+ C1- GND 15 C2+ V+ 2 + DB9 3 7 10 8 9 0.1 F VDD OSC1 8 MHz + 10 k 1 F PTB4 1 k VDD + 2 1 F VDDAD 10 M 27 pF V- 6 5 C2- VDDA OSC2 MAX232 1 F PTB0 IRQ 10 k 10 k 9.1 V PTB1 10 k PTA1 10 k 74HC125 5 6 74HC125 3 2 VDD VSSAD PTA0 VSSA VSS 4 1 5 Figure 19-10. Normal Monitor Mode Circuit MC68HC908GR60A N.C. RST 27 pF 1 1 F + 3 4 1 F + VDD VCC C1+ + C1- GND 15 C2+ V+ 2 1 F VDD + DB9 3 + 9 8 N.C. IRQ N.C. PTB0 N.C. PTB1 N.C. 74HC125 5 6 74HC125 3 2 PTA1 10 k PTA0 4 1 5 PTB4 10 k 1 F 10 7 0.1 F OSC1 8 MHz V- 6 5 C2- 2 1 F VDDAD 10 M 27 pF 16 VDD VDDA OSC2 MAX232 VDD VSSAD VSSA VSS Figure 19-11. Forced Monitor Mode MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 269 Development Support Table 19-1. Monitor Mode Signal Requirements and Options Mode IRQ RST Reset Vector Serial Communication Mode Selection Communication Speed Divider PLL PTA0 PTA1 PTB0 PTB1 PTB4 COP External Bus Clock Frequency Baud Rate VTST VDD or VTST X 1 0 1 0 0 OFF Disabled 4.0 MHz 2.0 MHz 7200 VTST VDD or VTST X 1 0 1 0 1 OFF Disabled 8.0 MHz 2.0 MHz 7200 Forced Monitor VDD or VSS VDD $FF (blank) 1 0 X X X OFF Disabled 8.0 MHz 2.0 MHz 7200 User VDD or VSS VDD or VTST X X X X X X Enabled X X X COM [8] SSEL [10] DIV4 [16] -- -- OSC1 [13] -- -- Normal Monitor MON08 VTST RST Function [4] [6] [Pin No.] Not $FF -- MOD0 MOD1 [12] [14] 1. PTA0 must have a pullup resistor to VDD in monitor mode. 2. Communication speed in the table is an example to obtain a baud rate of 7200. Baud rate using external oscillator is bus frequency / 278. 3. External clock is a 4.0 MHz or 8.0 MHz crystal on OSC1 and OSC2 or a canned oscillator on OSC1. 4. X = don't care 5. MON08 pin refers to P&E Microcomputer Systems' MON08-Cyclone 2 by 8-pin connector. NC 1 2 GND NC 3 4 RST NC 5 6 IRQ NC 7 8 PTA0 NC 9 10 PTA1 NC 11 12 PTB0 OSC1 13 14 PTB1 VDD 15 16 PTB4 Enter monitor mode with pin configuration shown in Table 19-1 by pulling RST low and then high. The rising edge of RST latches monitor mode. Once monitor mode is latched, the levels on the port pins except PTA0 can change. Once out of reset, the MCU waits for the host to send eight security bytes (see 19.3.2 Security). After the security bytes, the MCU sends a break signal (10 consecutive 0s) to the host, indicating that it is ready to receive a command. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 270 Freescale Semiconductor Monitor Module (MON) 19.3.1.1 Normal Monitor Mode If VTST is applied to IRQ and PTB4 is low upon monitor mode entry, the bus frequency is a divide-by-two of the input clock. If PTB4 is high with VTST applied to IRQ upon monitor mode entry, the bus frequency will be a divide-by-four of the input clock. Holding the PTB4 pin low when entering monitor mode causes a bypass of a divide-by-two stage at the oscillator only if VTST is applied to IRQ. In this event, the CGMOUT frequency is equal to the CGMXCLK frequency, and the OSC1 input directly generates internal bus clocks. In this case, the OSC1 signal must have a 50% duty cycle at maximum bus frequency. When monitor mode was entered with VTST on IRQ, the computer operating properly (COP) is disabled as long as VTST is applied to either IRQ or RST. This condition states that as long as VTST is maintained on the IRQ pin after entering monitor mode, or if VTST is applied to RST after the initial reset to get into monitor mode (when VTST was applied to IRQ), then the COP will be disabled. In the latter situation, after VTST is applied to the RST pin, VTST can be removed from the IRQ pin in the interest of freeing the IRQ for normal functionality in monitor mode. 19.3.1.2 Forced Monitor Mode If entering monitor mode without high voltage on IRQ, then all port B pin requirements and conditions, including the PTB4 frequency divisor selection, are not in effect. This is to reduce circuit requirements when performing in-circuit programming. NOTE If the reset vector is blank and monitor mode is entered, the chip will see an additional reset cycle after the initial power-on reset (POR). Once the reset vector has been programmed, the traditional method of applying a voltage, VTST, to IRQ must be used to enter monitor mode. An external oscillator of 8 MHz is required for a baud rate of 7200, as the internal bus frequency is automatically set to the external frequency divided by four. When the forced monitor mode is entered the COP is always disabled regardless of the state of IRQ or RST. 19.3.1.3 Monitor Vectors In monitor mode, the MCU uses different vectors for reset, SWI (software interrupt), and break interrupt than those for user mode. The alternate vectors are in the $FE page instead of the $FF page and allow code execution from the internal monitor firmware instead of user code. Table 19-2 summarizes the differences between user mode and monitor mode. Table 19-2. Mode Differences Functions Modes Reset Vector High Reset Vector Low Break Vector High Break Vector Low SWI Vector High SWI Vector Low User $FFFE $FFFF $FFFC $FFFD $FFFC $FFFD Monitor $FEFE $FEFF $FEFC $FEFD $FEFC $FEFD MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 271 Development Support 19.3.1.4 Data Format Communication with the monitor ROM is in standard non-return-to-zero (NRZ) mark/space data format. Transmit and receive baud rates must be identical. START BIT BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 STOP BIT NEXT START BIT Figure 19-12. Monitor Data Format 19.3.1.5 Break Signal A start bit (0) followed by nine 0 bits is a break signal. When the monitor receives a break signal, it drives the PTA0 pin high for the duration of approximately two bits and then echoes back the break signal. MISSING STOP BIT 0 1 2 3 4 5 6 APPROXIMATELY 2 BITS DELAY BEFORE ZERO ECHO 7 0 1 2 3 4 5 6 7 Figure 19-13. Break Transaction 19.3.1.6 Baud Rate The communication baud rate is controlled by the crystal frequency or external clock and the state of the PTB4 pin (when IRQ is set to VTST) upon entry into monitor mode. If monitor mode was entered with VDD on IRQ and the reset vector blank, then the baud rate is independent of PTB4. Table 19-1 also lists external frequencies required to achieve a standard baud rate of 7200 bps. The effective baud rate is the bus frequency divided by 278. If using a crystal as the clock source, be aware of the upper frequency limit that the internal clock module can handle. See 20.7 5.0-Volt Control Timing or 20.8 3.3-Volt Control Timing for this limit. 19.3.1.7 Commands The monitor ROM firmware uses these commands: * READ (read memory) * WRITE (write memory) * IREAD (indexed read) * IWRITE (indexed write) * READSP (read stack pointer) * RUN (run user program) The monitor ROM firmware echoes each received byte back to the PTA0 pin for error checking. An 11-bit delay at the end of each command allows the host to send a break character to cancel the command. A delay of two bit times occurs before each echo and before READ, IREAD, or READSP data is returned. The data returned by a read command appears after the echo of the last byte of the command. NOTE Wait one bit time after each echo before sending the next byte. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 272 Freescale Semiconductor Monitor Module (MON) FROM HOST 4 ADDRESS HIGH READ READ 4 1 ADDRESS HIGH ADDRESS LOW 1 ADDRESS LOW 4 DATA 1 3, 2 4 ECHO RETURN Notes: 1 = Echo delay, approximately 2 bit times 2 = Data return delay, approximately 2 bit times 3 = Cancel command delay, 11 bit times 4 = Wait 1 bit time before sending next byte. Figure 19-14. Read Transaction FROM HOST 3 ADDRESS HIGH WRITE WRITE 3 1 ADDRESS HIGH 1 ADDRESS LOW 3 ADDRESS LOW 1 DATA DATA 3 1 2, 3 ECHO Notes: 1 = Echo delay, approximately 2 bit times 2 = Cancel command delay, 11 bit times 3 = Wait 1 bit time before sending next byte. Figure 19-15. Write Transaction A brief description of each monitor mode command is given in Table 19-3 through Table 19-8. Table 19-3. READ (Read Memory) Command Description Read byte from memory Operand 2-byte address in high-byte:low-byte order Data Returned Returns contents of specified address Opcode $4A Command Sequence SENT TO MONITOR READ ECHO READ ADDRESS HIGH ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA RETURN MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 273 Development Support Table 19-4. WRITE (Write Memory) Command Description Operand Data Returned Opcode Write byte to memory 2-byte address in high-byte:low-byte order; low byte followed by data byte None $49 Command Sequence FROM HOST WRITE ADDRESS HIGH WRITE ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA DATA ECHO Table 19-5. IREAD (Indexed Read) Command Description Operand Data Returned Opcode Read next 2 bytes in memory from last address accessed None Returns contents of next two addresses $1A Command Sequence FROM HOST IREAD IREAD DATA ECHO DATA RETURN Table 19-6. IWRITE (Indexed Write) Command Description Operand Data Returned Opcode Write to last address accessed + 1 Single data byte None $19 Command Sequence FROM HOST IWRITE IWRITE DATA DATA ECHO A sequence of IREAD or IWRITE commands can access a block of memory sequentially over the full 64-Kbyte memory map. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 274 Freescale Semiconductor Monitor Module (MON) Table 19-7. READSP (Read Stack Pointer) Command Description Operand Data Returned Opcode Reads stack pointer None Returns incremented stack pointer value (SP + 1) in high-byte:low-byte order $0C Command Sequence FROM HOST READSP SP HIGH READSP SP LOW ECHO RETURN Table 19-8. RUN (Run User Program) Command Description Operand Data Returned Opcode Executes PULH and RTI instructions None None $28 Command Sequence FROM HOST RUN RUN ECHO The MCU executes the SWI and PSHH instructions when it enters monitor mode. The RUN command tells the MCU to execute the PULH and RTI instructions. Before sending the RUN command, the host can modify the stacked CPU registers to prepare to run the host program. The READSP command returns the incremented stack pointer value, SP + 1. The high and low bytes of the program counter are at addresses SP + 5 and SP + 6. SP HIGH BYTE OF INDEX REGISTER SP + 1 CONDITION CODE REGISTER SP + 2 ACCUMULATOR SP + 3 LOW BYTE OF INDEX REGISTER SP + 4 HIGH BYTE OF PROGRAM COUNTER SP + 5 LOW BYTE OF PROGRAM COUNTER SP + 6 SP + 7 Figure 19-16. Stack Pointer at Monitor Mode Entry MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 275 Development Support 19.3.2 Security A security feature discourages unauthorized reading of FLASH locations while in monitor mode. The host can bypass the security feature at monitor mode entry by sending eight security bytes that match the bytes at locations $FFF6-$FFFD. Locations $FFF6-$FFFD contain user-defined data. NOTE Do not leave locations $FFF6-$FFFD blank. For security reasons, program locations $FFF6-$FFFD even if they are not used for vectors. During monitor mode entry, the MCU waits after the power-on reset for the host to send the eight security bytes on pin PTA0. If the received bytes match those at locations $FFF6-$FFFD, the host bypasses the security feature and can read all FLASH locations and execute code from FLASH. Security remains bypassed until a power-on reset occurs. If the reset was not a power-on reset, security remains bypassed and security code entry is not required. See Figure 19-17. Upon power-on reset, if the received bytes of the security code do not match the data at locations $FFF6-$FFFD, the host fails to bypass the security feature. The MCU remains in monitor mode, but reading a FLASH location returns an invalid value and trying to execute code from FLASH causes an illegal address reset. After receiving the eight security bytes from the host, the MCU transmits a break character, signifying that it is ready to receive a command. NOTE The MCU does not transmit a break character until after the host sends the eight security bytes. VDD 4096 + 32 CGMXCLK CYCLES COMMAND BYTE 8 BYTE 2 FROM HOST BYTE 1 RST PA0 4 BREAK 2 1 COMMAND ECHO 1 BYTE 8 ECHO Notes: 1 = Echo delay, approximately 2 bit times 2 = Data return delay, approximately 2 bit times 4 = Wait 1 bit time before sending next byte 5 = Wait until the monitor ROM runs 1 BYTE 2 ECHO FROM MCU 4 1 BYTE 1 ECHO 5 Figure 19-17. Monitor Mode Entry Timing To determine whether the security code entered is correct, check to see if bit 6 of RAM address $40 is set. If it is, then the correct security code has been entered and FLASH can be accessed. If the security sequence fails, the device should be reset by a power-on reset and brought up in monitor mode to attempt another entry. After failing the security sequence, the FLASH module can also be mass erased by executing an erase routine that was downloaded into internal RAM. The mass erase operation clears the security code locations so that all eight security bytes become $FF (blank). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 276 Freescale Semiconductor Chapter 20 Electrical Specifications 20.1 Introduction This section contains electrical and timing specifications. 20.2 Absolute Maximum Ratings Maximum ratings are the extreme limits to which the MCU can be exposed without permanently damaging it. NOTE This device is not guaranteed to operate properly at the maximum ratings. Refer to 20.5 5.0-Vdc Electrical Characteristics for guaranteed operating conditions. Characteristic(1) Symbol Value Unit Supply voltage VDD -0.3 to + 6.0 V Input voltage VIn VSS - 0.3 to VDD + 0.3 V I 15 mA IPTC0-PTC4 25 mA Maximum current into VDD Imvdd 150 mA Maximum current out of VSS Imvss 150 mA Storage temperature Tstg -55 to +150 C Maximum current per pin excluding those specified below Maximum current for pins PTC0-PTC4 1. Voltages referenced to VSS NOTE This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum-rated voltages to this high-impedance circuit. For proper operation, it is recommended that VIn and VOut be constrained to the range VSS (VIn or VOut) VDD. Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level (for example, either VSS or VDD). MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 277 Electrical Specifications 20.3 Functional Operating Range Characteristic Operating temperature range Operating voltage range Symbol Value Unit TA -40 to +125 C VDD 5.0 10% 3.3 10% V 20.4 Thermal Characteristics Characteristic Symbol Value Unit Thermal resistance 32-pin LQFP 48-pin LQFP 64-pin QFP JA 95 95 54 C/W I/O pin power dissipation PI/O User determined W Power dissipation(1) PD PD = (IDD x VDD) + PI/O = K/(TJ + 273 C) W Constant(2) K Average junction temperature TJ PD x (TA + 273 C) + PD2 x JA W/C TA + (PD x JA) C 1. Power dissipation is a function of temperature. 2. K is a constant unique to the device. K can be determined for a known TA and measured PD. With this value of K, PD and TJ can be determined for any value of TA. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 278 Freescale Semiconductor 5.0-Vdc Electrical Characteristics 20.5 5.0-Vdc Electrical Characteristics Characteristic(1) Symbol Min Typ(2) Max Unit VOH VOH VOH IOH1 VDD - 0.8 VDD - 1.5 VDD - 1.5 -- -- -- -- -- -- -- -- 50 V V V mA IOH2 -- -- 50 mA IOHT -- -- 100 mA VOL VOL VOL IOL1 -- -- -- -- -- -- -- -- 0.4 1.5 1.5 50 V V V mA IOL2 -- -- 50 mA IOLT -- -- 100 mA Input high voltage All ports, IRQ, RST, OSC1 VIH 0.7 x VDD -- VDD V Input low voltage All ports, IRQ, RST, OSC1 VIL VSS -- 0.2 x VDD V -- -- -- -- -- -- 20 6 0.6 1 1.25 250 30 12 10 1.25 1.6 350 mA mA A mA mA A 0 0 -- -- 2 -0.2 mA 0 0 -- -- 25 -5 0 -- 1 Output high voltage (ILoad = -2.0 mA) all I/O pins (ILoad = -10.0 mA) all I/O pins (ILoad = -20.0 mA) pins PTC0-PTC4, PTF0-PTF3 only Maximum combined IOH for port PTA7-PTA3, port PTC0-PTC1, port E, port PTD0-PTD3, port PTF0-PTF3, port PTG4-PTG7 Maximum combined IOH for port PTA2-PTA0, port B, port PTC2-PTC6, port PTD4-PTD7, port PTF4-PTF7, port PTG0-PTG3 Maximum total IOH for all port pins Output low voltage (ILoad = 1.6 mA) all I/O pins (ILoad = 10 mA) all I/O pins (ILoad = 20 mA) pins PTC0-PTC4, PTF0-PTF3 only Maximum combined IOH for port PTA7-PTA3, port PTC0-PTC1, port E, port PTD0-PTD3, port PTF0-PTF3, port PTG4-PTG7 Maximum combined IOH for port PTA2-PTA0, port B, port PTC2-PTC6, port PTD4-PTD7, port PTF4-PTF7, port PTG0-PTG3 Maximum total IOL for all port pins VDD supply current Run(3) Wait(4) Stop(5) Stop with TBM enabled(6) Stop with LVI and TBM enabled(6) Stop with LVI IDD DC injection current(7) (8) (9) (10) Single pin limit Vin > VDD Vin < VSS Total MCU limit, includes sum of all stressed pins Vin > VDD Vin < VSS IIC I/O ports Hi-Z leakage current(11) IIL A Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 279 Electrical Specifications Characteristic(1) Symbol Min Typ(2) Max Unit Pullup/pulldown resistors (as input only) Ports PTA7/KBD7-PTA0/KBD0, PTC6-PTC0/CANTX, PTD7/T2CH1-PTD0/SS RPU 20 45 65 k Capacitance Ports (as input or output) COut CIn -- -- -- -- 12 8 pF Monitor mode entry voltage VTST VDD + 2.5 -- VDD + 4.0 V Low-voltage inhibit, trip falling voltage VTRIPF 3.90 4.25 4.50 V Low-voltage inhibit, trip rising voltage VTRIPR 4.0 4.35 4.60 V Low-voltage inhibit reset/recover hysteresis (VTRIPF + VHYS = VTRIPR) VHYS -- 100 -- mV POR rearm voltage(12) VPOR 0 -- 100 mV POR reset voltage(13) VPORRST 0 700 800 mV RPOR 0.035 -- -- V/ms POR rise time ramp rate(14) 1. VDD = 5.0 Vdc 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted 2. Typical values reflect average measurements at midpoint of voltage range, 25C only. 3. Run (operating) IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects run IDD. Measured with all modules enabled. 4. Wait IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait IDD. Measured with CGM and LVI enabled. 5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. Typical values at midpoint of voltage range, 25C only. 6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 8 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs. 7. This parameter is characterized and not tested on each device. 8. All functional non-supply pins are internally clamped to VSS and VDD. 9. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 10. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall power consumption). 11. Pullups and pulldowns are disabled. Port B leakage is specified in 20.10 5.0-Volt ADC Characteristics. 12. Maximum is highest voltage that POR is guaranteed. 13. Maximum is highest voltage that POR is possible. 14. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum VDD is reached. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 280 Freescale Semiconductor 3.3-Vdc Electrical Characteristics 20.6 3.3-Vdc Electrical Characteristics Characteristic(1) Symbol Min Typ(2) Max Unit VOH VOH VOH IOH1 VDD - 0.3 VDD - 1.0 VDD - 1.0 -- -- -- -- -- -- -- -- 30 V V V mA IOH2 -- -- 30 mA IOHT -- -- 60 mA VOL VOL VOL IOL1 -- -- -- -- -- -- -- -- 0.3 1.0 0.8 30 V V V mA IOL2 -- -- 30 mA IOLT -- -- 60 mA Input high voltage All ports, IRQ, RST, OSC1 VIH 0.7 x VDD -- VDD V Input low voltage All ports, IRQ, RST, OSC1 VIL VSS -- 0.3 x VDD V -- -- -- -- -- -- 8 3 0.5 500 700 200 12 6 6 700 900 300 mA mA A A A A 0 0 -- -- 2 -0.2 mA 0 0 -- -- 25 -5 0 -- 1 Output high voltage (ILoad = -0.6 mA) all I/O pins (ILoad = -4.0 mA) all I/O pins (ILoad = -10.0 mA) pins PTC0-PTC4, PTF0-PTF3 only Maximum combined IOH for port PTA7-PTA3, port PTC0-PTC1, port E, port PTD0-PTD3, port PTF0-PTF3, port PTG4-PTG7 Maximum combined IOH for port PTA2-PTA0, port B, port PTC2-PTC6, port PTD4-PTD7 port PTF4-PTF7, port PTG0-PTG3 Maximum total IOH for all port pins Output low voltage (ILoad = 0.5 mA) all I/O pins (ILoad = 5 mA) all I/O pins (ILoad = 10 mA) pins PTC0-PTC4, PTF0-PTF3 only Maximum combined IOH for port PTA7-PTA3, port PTC0-PTC1, port E, port PTD0-PTD3 port PTF0-PTF3, port PTG4-PTG7 Maximum combined IOH for port PTA2-PTA0, port B, port PTC2-PTC6, port PTD4-PTD7 port PTF4-PTF7, port PTG0-PTG3 Maximum total IOL for all port pins VDD supply current Run(3) Wait(4) Stop(5) Stop with TBM enabled(6) Stop with LVI and TBM enabled(6) Stop with LVI IDD DC injection current(7) (8) (9) (10) Single pin limit Vin > VDD Vin < VSS Total MCU limit, includes sum of all stressed pins Vin > VDD Vin < VSS IIC I/O ports Hi-Z leakage current(11) IIL A Continued on next page MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 281 Electrical Specifications Characteristic(1) Symbol Min Typ(2) Max Unit Pullup/pulldown resistors (as input only) Ports PTA7/KBD7-PTA0/KBD0, PTC6-PTC0, PTD7/T2CH1-PTD0/SS RPU 20 45 65 k Capacitance Ports (as input or output) COut CIn -- -- -- -- 12 8 pF Monitor mode entry voltage VTST VDD + 2.5 -- VDD + 4.0 V Low-voltage inhibit, trip falling voltage VTRIPF 2.35 2.6 2.8 V Low-voltage inhibit, trip rising voltage VTRIPR 2.4 2.66 2.9 V Low-voltage inhibit reset/recover hysteresis (VTRIPF + VHYS = VTRIPR) VHYS -- 100 -- mV POR rearm voltage(12) VPOR 0 -- 100 mV POR reset voltage(13) VPORRST 0 700 800 mV RPOR 0.02 -- -- V/ms POR rise time ramp rate(14) 1. VDD = 3.3 Vdc 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted 2. Typical values reflect average measurements at midpoint of voltage range, 25C only. 3. Run (operating) IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects run IDD. Measured with all modules enabled. 4. Wait IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait IDD. Measured with CGM and LVI enabled. 5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. Typical values at midpoint of voltage range, 25C only. 6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 4 MHz). All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs. 7. This parameter is characterized and not tested on each device. 8. All functional non-supply pins are internally clamped to VSS and VDD. 9. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 10. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall power consumption). 11. Pullups and pulldowns are disabled. 12. Maximum is highest voltage that POR is guaranteed. 13. Maximum is highest voltage that POR is possible. 14. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum VDD is reached. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 282 Freescale Semiconductor 5.0-Volt Control Timing 20.7 5.0-Volt Control Timing Characteristic(1) Symbol Min Max Unit fOSC 1 dc 8 32 MHz Internal operating frequency fOP (fBus) -- 8 MHz Internal clock period (1/fOP) tCYC 125 -- ns RESET input pulse width low tRL 100 -- ns IRQ interrupt pulse width low (edge-triggered) tILIH 100 -- ns tILIL Note 3 -- tCYC Frequency of operation Crystal option External clock option(2) (3) IRQ interrupt pulse period 1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted. 2. No more than 10% duty cycle deviation from 50%. 3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC. 20.8 3.3-Volt Control Timing Characteristic(1) Symbol Min Max Unit fOSC 1 dc 8 16 MHz Internal operating frequency fOP (fBus) -- 4 MHz Internal clock period (1/fOP) tCYC 250 -- ns RESET input pulse width low tRL 200 -- ns IRQ interrupt pulse width low (edge-triggered) tILIH 200 -- ns IRQ interrupt pulse period(3) tILIL Note 3 -- tCYC Frequency of operation Crystal option External clock option(2) 1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted. 2. No more than 10% duty cycle deviation from 50%. 3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC. tRL RST tILIL tILIH IRQ Figure 20-1. RST and IRQ Timing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 283 Electrical Specifications 20.9 Clock Generation Module (CGM) Characteristics 20.9.1 CGM Operating Conditions Characteristic Symbol Min Typ Max Unit Operating voltage VDDA VSSA VDD - 0.3 VSS - 0.3 -- -- VDD + 0.3 VSS + 0.3 V Crystal reference frequency fRCLK 1 -- 8 MHz Input clock frequency (PLL off)(1) fXCLK -- -- 32 MHz Range nominal multiplier fNOM -- 71.42 -- kHz VCO center-of-range frequency(2) fVRS 71.42k -- 40M Hz VCO operating frequency(3) fVCLK 71.42k -- 32M Hz 1. External square wave applied to OSC1. Voltage levels must be rail-to-rail and duty cycle must be 50%. 2. Range of frequencies that VCO can produce to generate input clock to frequency divider during acquisition and tracking modes. 3. Allowed VCO operating range. 20.9.2 CGM Component Information Characteristic Symbol Min Typ Max Unit fXCLK 1 -- 8 MHz Crystal load capacitance(1) CL -- 20 -- pF Crystal fixed capacitance(2) C1 -- (2 x CL) - 5 47 pF Crystal tuning capacitance(3) C2 -- (2 x CL) - 5 47 pF Feedback bias resistor RB -- 1 10 M Series damping resistor RS 0 0 -- k Cbyp -- 0.1 -- F Crystal frequency VDDA/VSSA bypass capacitor CGMXFC filter values See Table 4-5. Example Filter Component Values 1. Consult crystal manufacturer's specification. 2. Capacitor on OSC1 pin. Does not include parasitic capacitance due to package, pin, and board. 3. Capacitor on OSC2 pin. Does not include parasitic capacitance due to package, pin, and board. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 284 Freescale Semiconductor Clock Generation Module (CGM) Characteristics 20.9.3 CGM Acquisition/Lock Time Information Characteristic Symbol Min Typ Max Unit Acquisition mode entry frequency tolerance(1) ACQ 3.6 -- 7.2 % Tracking mode entry frequency tolerance(2) TRK 0 -- 3.6 % LOCK entry frequency tolerance(3) LOCK 0 -- 0.9 % LOCK exit frequency tolerance(4) UNL 0.9 -- 1.8 % Reference cycles per acquisition mode period nACQ -- 32 -- Reference cycles per tracking mode period nTRK -- 128 -- Automatic mode time to stable tACQ nACQ/fRCLK See note(5) -- s tAL nTRK/fRCLK See note(6) -- s tLOCK -- 5 25 ms fJ 0 -- fRCLK x 0.025% x N/4 Hz Automatic stable to lock time Automatic lock time (tACQ + tAL)(7) PLL jitter, deviation of average bus frequency over 2 ms period 1. Deviation between VCO frequency and desired frequency to enter PLL acquisition mode. 2. Deviation between VCO frequency and desired frequency to enter PLL tracking mode (stable). 3. Deviation between VCO frequency and desired frequency to enter locked mode. 4. Deviation between VCO frequency and desired frequency to exit locked mode. 5. Acquisition time is an integer multiple of reference cycles divided by reference clock. 6. Stable to lock time is an integer multiple of reference cycles divided by reference clock. 7. Maximum lock time depends on CGMXFC filter components, power supply filtering, and reference clock stability. PLL may not lock if improper components or poor filtering and layout are used. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 285 Electrical Specifications 20.10 5.0-Volt ADC Characteristics Characteristic(1) Symbol Min Max Unit Comments Supply voltage VDDAD 4.5 5.5 V VDDAD should be tied to the same potential as VDD via separate traces. Input voltages VADIN 0 VDDAD V VADIN <= VDDAD Resolution BAD 10 10 Bits Absolute accuracy AAD -4 +4 LSB Includes quantization ADC internal clock fADIC 500 k 1.048 M Hz tAIC = 1/fADIC Conversion range RAD VSSAD VDDAD V Power-up time tADPU 16 -- tAIC cycles Conversion time tADC 16 17 tAIC cycles Sample time tADS 5 -- tAIC cycles Monotonicity MAD Zero input reading ZADI 000 003 Hex VADIN = VSSA Full-scale reading FADI 3FC 3FF Hex VADIN = VDDA Input capacitance CADI -- 30 pF Not tested VDDAD/VREFH current IVREF -- 1.6 mA Absolute accuracy (8-bit truncation mode) AAD -1 +1 LSB Quantization error (8-bit truncation mode) -- -1/8 +7/8 LSB Guaranteed Includes quantization 1. VDD = 5.0 Vdc 10%, VSS = 0 Vdc, VDDAD/VREFH = 5.0 Vdc 10%, VSSAD/VREFL = 0 Vdc MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 286 Freescale Semiconductor 3.3-Volt ADC Characteristics 20.11 3.3-Volt ADC Characteristics Characteristic(1) Symbol Min Max Unit Comments Supply voltage VDDAD 3.0 3.6 V VDDAD should be tied to the same potential as VDD via separate traces. Input voltages VADIN 0 VDDAD V VADIN <= VDDAD Resolution BAD 10 10 Bits Absolute accuracy AAD -6 +6 LSB Includes quantization ADC internal clock fADIC 500 k 1.048 M Hz tAIC = 1/fADIC Conversion range RAD VSSAD VDDAD V Power-up time tADPU 16 -- tAIC cycles Conversion time tADC 16 17 tAIC cycles Sample time tADS 5 -- tAIC cycles Monotonicity MAD Zero input reading ZADI 000 005 Hex VADIN = VSSA Full-scale reading FADI 3FA 3FF Hex VADIN = VDDA Input capacitance CADI -- 30 pF Not tested VDDAD/VREFH current IVREF -- 1.2 mA Absolute accuracy (8-bit truncation mode) AAD -1 +1 LSB Quantization error (8-bit truncation mode) -- -1/8 +7/8 LSB Guaranteed Includes quantization 1. VDD = 3.3 Vdc 10%, VSS = 0 Vdc, VDDAD/VREFH = 3.3 Vdc 10%, VSSAD/VREFL = 0 Vdc MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 287 Electrical Specifications 20.12 5.0-Volt SPI Characteristics Diagram Number(1) Characteristic(2) Symbol Min Max Unit Operating frequency Master Slave fOP(M) fOP(S) fOP/128 dc fOP/2 fOP MHz MHz 1 Cycle time Master Slave tCYC(M) tCYC(S) 2 1 128 -- tCYC tCYC 2 Enable lead time tLead(S) 1 -- tCYC 3 Enable lag time tLag(S) 1 -- tCYC 4 Clock (SPSCK) high time Master Slave tSCKH(M) tSCKH(S) tCYC -25 1/2 tCYC -25 64 tCYC -- ns ns 5 Clock (SPSCK) low time Master Slave tSCKL(M) tSCKL(S) tCYC -25 1/2 tCYC -25 64 tCYC -- ns ns 6 Data setup time (inputs) Master Slave tSU(M) tSU(S) 30 30 -- -- ns ns 7 Data hold time (inputs) Master Slave tH(M) tH(S) 30 30 -- -- ns ns 8 Access time, slave(3) CPHA = 0 CPHA = 1 tA(CP0) tA(CP1) 0 0 40 40 ns ns 9 Disable time, slave(4) tDIS(S) -- 40 ns 10 Data valid time, after enable edge Master Slave(5) tV(M) tV(S) -- -- 50 50 ns ns 11 Data hold time, outputs, after enable edge Master Slave tHO(M) tHO(S) 0 0 -- -- ns ns 1. Numbers refer to dimensions in Figure 20-2 and Figure 20-3. 2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins. 3. Time to data active from high-impedance state 4. Hold time to high-impedance state 5. With 100 pF on all SPI pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 288 Freescale Semiconductor 3.3-Volt SPI Characteristics 20.13 3.3-Volt SPI Characteristics Diagram Number(1) Characteristic(2) Symbol Min Max Unit Operating frequency Master Slave fOP(M) fOP(S) fOP/128 DC fOP/2 fOP MHz MHz 1 Cycle time Master Slave tCYC(M) tCYC(S) 2 1 128 -- tcyc tcyc 2 Enable lead time tLead(S) 1 -- tcyc 3 Enable lag time tLag(S) 1 -- tcyc 4 Clock (SPSCK) high time Master Slave tSCKH(M) tSCKH(S) tcyc -35 1/2 tcyc -35 64 tcyc -- ns ns 5 Clock (SPSCK) low time Master Slave tSCKL(M) tSCKL(S) tcyc -35 1/2 tcyc -35 64 tcyc -- ns ns 6 Data setup time (inputs) Master Slave tSU(M) tSU(S) 40 40 -- -- ns ns 7 Data hold time (inputs) Master Slave tH(M) tH(S) 40 40 -- -- ns ns 8 Access time, slave(3) CPHA = 0 CPHA = 1 tA(CP0) tA(CP1) 0 0 50 50 ns ns 9 Disable time, slave(4) tDIS(S) -- 50 ns 10 Data valid time, after enable edge Master Slave(5) tV(M) tV(S) -- -- 60 60 ns ns 11 Data hold time, outputs, after enable edge Master Slave tHO(M) tHO(S) 0 0 -- -- ns ns 1. Numbers refer to dimensions in Figure 20-2 and Figure 20-3. 2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins. 3. Time to data active from high-impedance state 4. Hold time to high-impedance state 5. With 100 pF on all SPI pins MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 289 Electrical Specifications SS INPUT SS PIN OF MASTER HELD HIGH 1 SPSCK OUTPUT CPOL = 0 NOTE SPSCK OUTPUT CPOL = 1 NOTE 5 4 5 4 6 MISO INPUT MSB IN BITS 6-1 11 MOSI OUTPUT MASTER MSB OUT 7 LSB IN 10 11 BITS 6-1 MASTER LSB OUT Note: This first clock edge is generated internally, but is not seen at the SPSCK pin. a) SPI Master Timing (CPHA = 0) SS INPUT SS PIN OF MASTER HELD HIGH 1 SPSCK OUTPUT CPOL = 0 5 NOTE 4 SPSCK OUTPUT CPOL = 1 5 NOTE 4 6 MISO INPUT MSB IN 10 MOSI OUTPUT BITS 6-1 11 MASTER MSB OUT 7 LSB IN 10 BITS 6-1 MASTER LSB OUT Note: This last clock edge is generated internally, but is not seen at the SPSCK pin. b) SPI Master Timing (CPHA = 1) Figure 20-2. SPI Master Timing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 290 Freescale Semiconductor 3.3-Volt SPI Characteristics SS INPUT 3 1 SPSCK INPUT CPOL = 0 5 4 2 SPSCK INPUT CPOL = 1 5 4 9 8 MISO INPUT SLAVE MSB OUT 6 MOSI OUTPUT BITS 6-1 7 NOTE 11 11 10 MSB IN SLAVE LSB OUT BITS 6-1 LSB IN Note: Not defined but normally MSB of character just received a) SPI Slave Timing (CPHA = 0) SS INPUT 1 SPSCK INPUT CPOL = 0 5 4 2 3 SPSCK INPUT CPOL = 1 8 MISO OUTPUT MOSI INPUT 5 4 10 NOTE 9 SLAVE MSB OUT 6 7 BITS 6-1 11 10 MSB IN SLAVE LSB OUT BITS 6-1 LSB IN Note: Not defined but normally LSB of character previously transmitted b) SPI Slave Timing (CPHA = 1) Figure 20-3. SPI Slave Timing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 291 Electrical Specifications 20.14 Timer Interface Module Characteristics Characteristic Symbol Min Max Unit tTH, tTL 2 -- tcyc tTLTL Note(1) -- tcyc tTCL, tTCH tcyc + 5 -- ns Timer input capture pulse width Timer input capture period Timer input clock pulse width 1. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tcyc. tTLTL tTH INPUT CAPTURE RISING EDGE tTLTL tTL INPUT CAPTURE FALLING EDGE tTLTL tTH tTL INPUT CAPTURE BOTH EDGES tTCH TCLK tTCL Figure 20-4. Timer Input Timing MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 292 Freescale Semiconductor Memory Characteristics 20.15 Memory Characteristics Characteristic Symbol Min Typ Max Unit VRDR 1.3 -- -- V -- 1 -- -- MHz fRead(1) 0 -- 8M Hz FLASH page erase time <1 k cycles >1 k cycles tErase 0.9 3.6 1 4 1.1 5.5 ms FLASH mass erase time tMErase 4 -- -- ms FLASH PGM/ERASE to HVEN setup time tNVS 10 -- -- s FLASH high-voltage hold time tNVH 5 -- -- s FLASH high-voltage hold time (mass erase) tNVHL 100 -- -- s FLASH program hold time tPGS 5 -- -- s FLASH program time tPROG 30 -- 40 s FLASH return to read time tRCV(2) 1 -- -- s FLASH cumulative program HV period tHV(3) -- -- 4 ms FLASH endurance(4) -- 10 k 100 k -- Cycles FLASH data retention time(5) -- 15 100 -- Years RAM data retention voltage FLASH program bus clock frequency FLASH read bus clock frequency 1. fRead is defined as the frequency range for which the FLASH memory can be read. 2. tRCV is defined as the time it needs before the FLASH can be read after turning off the high voltage charge pump, by clearing HVEN to 0. 3. tHV is defined as the cumulative high voltage programming time to the same row before next erase. tHV must satisfy this condition: tNVS + tNVH + tPGS + (tPROG x 32) tHV maximum. 4. Typical endurance was evaluated for this product family. For additional information on how Freescale Semiconductor defines Typical Endurance, please refer to Engineering Bulletin EB619. 5. Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines Typical Data Retention, please refer to Engineering Bulletin EB618. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 293 Electrical Specifications MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 294 Freescale Semiconductor Chapter 21 Ordering Information and Mechanical Specifications 21.1 Introduction This section contains ordering numbers for the MC68HC908GR60A and gives the dimensions for: * 32-pin low-profile quad flat pack (case 873A) * 48-pin low-profile quad flat pack (case 932-03) * 64-pin quad flat pack (case 840B) The following figures show the latest package drawings at the time of this publication. To make sure that you have the latest package specifications, contact your local Freescale Semiconductor Sales Office. 21.2 MC Order Numbers Table 21-1. MC Order Numbers MC Order Number Operating Temperature Range MC908GR60ACFJ -40C to +85C MC908GR60AVFJ -40C to +105C MC908GR60AMFJ -40C to +125C MC908GR60ACFA -40C to +85C MC908GR60AVFA -40C to +105C MC908GR60AMFA -40C to +125C MC908GR60ACFU -40C to +85C MC908GR60AVFU -40C to +105C MC908GR60AMFU -40C to +125C Package 32-pin low-profile quad flat package (LQFP) 48-pin low-profile quad flat package (LQFP) 64-pin quad flat package (QFP) Temperature designators: C = -40C to +85C V = -40C to +105C M = -40C to +125C M C 9 0 8 G R X X A X XX E FAMILY Pb FREE PACKAGE DESIGNATOR TEMPERATURE RANGE Figure 21-1. Device Numbering System 21.3 Package Dimensions Refer to the following pages for detailed package dimensions. MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 295 Appendix A MC68HC908GR48A A.1 Introduction The MC68HC908GR48A is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. The information contained in this document pertains to the MC68HC908GR48A with the exceptions shown in this appendix. A.2 Block Diagram See Figure A-1. A.3 Memory The MC68HC908GR48A can address 48 Kbytes of memory space. The memory map, shown in Figure A-2, includes: * 48 Kbytes of user FLASH memory * 1536 bytes of random-access memory (RAM) * 52 bytes of user-defined vectors MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 305 INTERNAL BUS MONITOR ROM -- 304 BYTES 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) PTE5-PTE2 PTE1/RxD PTE0/TxD SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR DDRF CGMXFC CLOCK GENERATOR MODULE DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 1536 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 48,640 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure A-1. MC68HC908GR48A Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 306 Freescale Semiconductor $0000 $003F I/O REGISTERS 64 BYTES $0040 $043F RAM-1 1024 BYTES $0440 $0461 I/O REGISTERS 34 BYTES $0462 $057F RESERVED $0580 $077F RAM-2 512 BYTES $0780 $1DFF RESERVED $1E00 $1E0F MONITOR ROM 16 BYTES $1E10 $3FFF RESERVED $4000 $7FFF FLASH-2 16,384 BYTES $8000 $FDFF FLASH-1 32,256 BYTES $FE00 SIM BREAK STATUS REGISTER (BSR) $FE01 SIM RESET STATUS REGISTER (SRSR) $FE02 RESERVED $FE03 SIM BREAK FLAG CONTROL REGISTER (BFCR) $FE04 INTERRUPT STATUS REGISTER 1 (INT1) $FE05 INTERRUPT STATUS REGISTER 2 (INT2) $FE06 INTERRUPT STATUS REGISTER 3 (INT3) $FE07 INTERRUPT STATUS REGISTER 4 (INT4) $FE08 FLASH-2 CONTROL REGISTER (FL2CR) $FE09 BREAK ADDRESS REGISTER HIGH (BRKH) $FE0A BREAK ADDRESS REGISTER LOW (BRKL) $FE0B BREAK STATUS AND CONTROL REGISTER (BRKSCR) $FE0C LVI STATUS REGISTER (LVISR) $FE0D FLASH-2 TEST CONTROL REGISTER (FLTCR2) $FE0E FLASH-1 TEST CONTROL REGISTER (FLTCR1) $FE0F UNIMPLEMENTED $FE10 $FE1F UNIMPLEMENTED 16 BYTES RESERVED FOR COMPATIBILITY WITH MONITOR CODE FOR A-FAMILY PART $FE20 $FF7F MONITOR ROM 352 BYTES $FF80 FLASH-1 BLOCK PROTECT REGISTER (FL1BPR) $FF81 FLASH-2 BLOCK PROTECT REGISTER (FL2BPR) $FF82 $FF87 RESERVED $FF88 FLASH-1 CONTROL REGISTER (FL1CR) $FF89 $FFCB RESERVED $FFCC $FFFF(1) FLASH-1 VECTORS 52 BYTES 1. $FFF6-$FFFD used for eight security bytes Figure A-2. MC68HC908GR48A Memory Map MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 307 A.4 Ordering Information Table A-1. MC Order Numbers MC Order Number Operating Temperature Range MC908GR48ACFJ -40C to +85C MC908GR48AVFJ -40C to +105C MC908GR48AMFJ -40C to +125C MC908GR48ACFA -40C to +85C MC908GR48AVFA -40C to +105C MC908GR48AMFA -40C to +125C MC908GR48ACFU -40C to +85C MC908GR48AVFU -40C to +105C MC908GR48AMFU -40C to +125C Package 32-pin low-profile quad flat package (LQFP) 48-pin low-profile quad flat package (LQFP) 64-pin quad flat package (QFP) Temperature designators: C = -40C to +85C V = -40C to +105C M = -40C to +125C M C 9 0 8 G R X X A X XX E FAMILY Pb FREE PACKAGE DESIGNATOR TEMPERATURE RANGE Figure A-3. Device Numbering System MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 308 Freescale Semiconductor Appendix B MC68HC908GR32A B.1 Introduction The MC68HC908GR32A is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. The information contained in this document pertains to the MC68HC908GR32A with the exceptions shown in this appendix. B.2 Block Diagram See Figure B-1. B.3 Memory The MC68HC908GR32A can address 32 Kbytes of memory space. The memory map, shown in Figure B-2, includes: * 32 Kbytes of user FLASH memory * 1536 bytes of random-access memory (RAM) * 52 bytes of user-defined vectors MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 309 INTERNAL BUS MONITOR ROM -- 304 BYTES 2-CHANNEL TIMER INTERFACE MODULE USER FLASH VECTOR SPACE -- 52 BYTES 6-CHANNEL TIMER INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE RST(1) SYSTEM INTEGRATION MODULE SERIAL PERIPHERAL INTERFACE MODULE IRQ(1) SINGLE EXTERNAL INTERRUPT MODULE MONITOR MODE ENTRY MODULE VSSAD/VREFL 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE VDD VSS VDDA VSSA POWER SECURITY MODULE MEMORY MAP MODULE PORTF VDDAD/VREFH PTE5-PTE2 PTE1/RxD PTE0/TxD PTF7/T2CH5 PTF6/T2CH4 PTF5/T2CH3 PTF4/T2CH2 PTF3-PFT0(3) CONFIGURATION REGISTER 1-2 MODULE PORTG PHASE LOCKED LOOP ENHANCED SERIAL COMMUNICATIONS INTERFACE MODULE DDRE 1-8 MHz OSCILLATOR PTD7/T2CH1(2) PTD6/T2CH0(2) PTD5/T1CH1(2) PTD4/T1CH0(2) PTD3/SPSCK(2) PTD2/MOSI(2) PTD1/MISO(2) PTD0/SS/MCLK(2) DDRF CGMXFC CLOCK GENERATOR MODULE PTC6(2) PTC5(2) PTC4(2, 3) PTC3(2, 3) PTC2(2, 3) PTC1(2, 3) PTC0(2, 3) DDRG OSC1 OSC2 PORTA 8-BIT KEYBOARD INTERRUPT MODULE PORTB USER RAM -- 1536 BYTES PORTC DUAL VOLTAGE LOW-VOLTAGE INHIBIT MODULE PORTD USER FLASH -- 32,256 BYTES PTB7/AD7-PTB0/AD0 PORTE SINGLE BREAKPOINT BREAK MODULE DDRA CONTROL AND STATUS REGISTERS -- 64 BYTES PTA7/KBD7/AD15- PTA0/KBD0/AD8(2) DDRC PROGRAMMABLE TIMEBASE MODULE DDRD ARITHMETIC/LOGIC UNIT (ALU) CPU REGISTERS DDRB M68HC08 CPU PTG7/AD23- PTG0/AD16 1. Pin contains integrated pullup device. 2. Ports are software configurable with pullup device if input port or pullup/pulldown device for keyboard input. 3. Higher current drive port pins Figure B-1. MC68HC908GR32A Block Diagram MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 310 Freescale Semiconductor $0000 $003F I/O REGISTERS 64 BYTES $0040 $043F RAM-1 1024 BYTES $0440 $0461 I/O REGISTERS 34 BYTES $FE04 INTERRUPT STATUS REGISTER 1 (INT1) $FE05 INTERRUPT STATUS REGISTER 2 (INT2) $FE06 INTERRUPT STATUS REGISTER 3 (INT3) $FE07 INTERRUPT STATUS REGISTER 4 (INT4) $FE08 UNIMPLEMENTED $FE09 BREAK ADDRESS REGISTER HIGH (BRKH) $FE0A BREAK ADDRESS REGISTER LOW (BRKL) $FE0B BREAK STATUS AND CONTROL REGISTER (BRKSCR) $FE0C LVI STATUS REGISTER (LVISR) $FE0D UNIMPLEMENTED $FE0E FLASH-1 TEST CONTROL REGISTER (FLTCR1) $FE0F UNIMPLEMENTED $0462 $057F RESERVED $0580 $077F RAM-2 512 BYTES $FE10 $FE1F UNIMPLEMENTED 16 BYTES RESERVED FOR COMPATIBILITY WITH MONITOR CODE FOR A-FAMILY PART $0780 $1DFF RESERVED $FE20 $FF7F MONITOR ROM 352 BYTES $1E00 $1E0F $FF80 FLASH-1 BLOCK PROTECT REGISTER (FL1BPR) MONITOR ROM 16 BYTES $FF81 $FF87 RESERVED $1E10 $7FFF RESERVED $FF88 FLASH-1 CONTROL REGISTER (FL1CR) $FF89 $FFCB RESERVED $FFCC $FFFF(1) FLASH-1 VECTORS 52 BYTES $8000 $FDFF FLASH-1 32,256 BYTES $FE00 SIM BREAK STATUS REGISTER (BSR) $FE01 SIM RESET STATUS REGISTER (SRSR) $FE02 RESERVED $FE03 SIM BREAK FLAG CONTROL REGISTER (7BFCR) 1. $FFF6-$FFFD used for eight security bytes Figure B-2. MC68HC908GR32A Memory Map MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 Freescale Semiconductor 311 B.4 Ordering Information Table B-1. MC Order Numbers MC Order Number Operating Temperature Range MC908GR32ACFJ -40C to +85C MC908GR32AVFJ -40C to +105C MC908GR32AMFJ -40C to +125C MC908GR32ACFA -40C to +85C MC908GR32AVFA -40C to +105C MC908GR32AMFA -40C to +125C MC908GR32ACFU -40C to +85C MC908GR32AVFU -40C to +105C MC908GR32AMFU -40C to +125C Package 32-pin low-profile quad flat package (LQFP) 48-pin low-profile quad flat package (LQFP) 64-pin quad flat package (QFP) Temperature designators: C = -40C to +85C V = -40C to +105C M = -40C to +125C M C 9 0 8 G R X X A X XX E FAMILY Pb FREE PACKAGE DESIGNATOR TEMPERATURE RANGE Figure B-3. Device Numbering System MC68HC908GR60A * MC68HC908GR48A * MC68HC908GR32A Data Sheet, Rev. 5 312 Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com MC68HC908GR60A Rev. 5, 04/2007 RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2004, 2006, 2007. All rights reserved.