Special Connectors AMP Spark Suppressor Connectors Features @Provides a very effec- tive and economic means of noise suppres- sion as the diode can be installed close to electromagnetic parts. No wire stripping MTwo versions available- standard type and smaller Mark II. Milnstallation of diode is simple. The standard type can be installed with a plier on the market, while Mark II by a special easy-to-use tool. @Additional noise sup- pression circuits can be installed. WDiodes can be replaced easily. Material: Housing94V-2 66 nylon, natural color ContactTin-plated brass AMP Spark Suppressor Connector is a product designed for use with a diode to suppress noise from the electromagnetic clutches, solenoids, electromagnetic counters, etc., incorporated into a variety of equipment. Con- sisting of a housing and two contacts, the connector provides a very effective and economic means of sup- pressing noise compared with conventional methods. Two versions are available. One is the conventional standard type and the other is Mark IE which has been newly developed. Compared to the standard type, this Mark II is more compact In size and can be mounted onto smaller diodes . To install a diode, there is no need of stripping wires. Work is done easily and without fail through inter- action between the housings wire mounting slot and the contacts slit. Th standard type connector can be mounted with a plier on the market, while the Mark I] connector with a special tool designed for exclusive use with it. The diode can be installed close to electromagnetic parts, so that noise will be suppressed to a minimum. Also, additional noise sup- plression circuits can be installed or the diode can be replaced easily if needed. In the past, when installing a diode to a equipment, it was necessary to apply for recognition as an applica- tlon under appropriate standards. With this Spark Suppressor Connector, the connector has been recognized by UL. Therefore, the period of qualification tests will be reduced. The housing is made of 94V-2 66 nylon, natural color and the contact is tin-plated brass. Performance Data <Standard Type> Wire size range: (UL1007) AWGE22, 20 (0.33-0.52mm} Wire insulation diameter: 1.75-1.95mm Applicable diode: Lead wire diameter 0.77-0.82mm Diode diameter 5mm max. Length7mm max. Operating temperature: 20~+105C Current rating: 3A Voltage rating: 250V AC Insulation resistance: more than 1,000M (initial) more than 100M (after humarty test) Withstading voltage between lines: 1.5kV AC Instruction Sheet: |S-079J Product Specifications: 108-5123 754 <Mark II Type> Wire size range: (UL1061/1571) AWG426, 424 7 stranded wire (0.14-0.23mm/) Wire insulation diameter: 1.2mm Applicable diode: Lead wire diameter 0.5-0.6mm Diode diameter 3mm max. Length3.5mm max. Operating temperature: 20~+105C Current rating: 1A Voitage rating: 250V AC Insulation resistance: more than 1,000MQ (initial) more than 100M2 (after humdity test) Withstanding voltage between lines: 1.5kV AC Instruction Sheet: |S-552J Product Specifications: 108-5346Special Connectors ~ AMP Spark Suppressor Connectors oo Standard Type Housing {the lid is part of housing} Part Number: 172006-1 Material: 66 Nylon, 94V-2 rated, Natural Contact (two required) Part Number: 170284-1 Material: Tin-plated Brass \, Mark II Type Housing (the lid is part of housing) Part Number: 178037-1 Material: 66 Nylon. 94V-2 rated, Natural Contact (two required) Part Number: 175222-1 Material: Tin-plated Brass Crimping Hand Tool Part Number: 915702-1 Dimple Contact (two) Contact (two) Locking rib (2 place) en 755 AMP Trade Mark Diode Mark (indicates the direction of place- ? ment of diode and also et is used for checking circuits) 60.82 $0.77 5 Max. 4 T | | TMax. | I- Cutting length -| 18~19.4 mm Diode (not furnished by AMP) Diode Mark (indicates the direction of place- ment of diode and also is used for checking circuits) AMP Trade Mark 3.5 Max. 3.0 Max. ax wos~o6. Fi ST Diode (not furnished by AMP)