APDS-9900 and APDS-9901 Digital Proximity and Ambient Light Sensor Data Sheet Description Features The APDS-9900/9901 provides digital ambient light sensing (ALS), IR LED and a complete proximity detection system in a single 8 pin package. The proximity function offers plug and play detection to 100 mm (without front glass) thus eliminating the need for factory calibration of the end equipment or sub-assembly. The proximity detection feature operates well from bright sunlight to dark rooms. The wide dynamic range also allows for operation in short distance detection behind dark glass such as a cell phone. In addition, an internal state machine provides the ability to put the device into a low power mode in between ALS and proximity measurements providing very low average power consumption. The ALS provides a photopic response to light intensity in very low light condition or behind a dark faceplate. ALS, IR LED and Proximity Detector in an Optical Module The APDS-9900/9901 is particularly useful for display management with the purpose of extending battery life and providing optimum viewing in diverse lighting conditions. Display panel and keyboard backlighting can account for up to 30 to 40 percent of total platform power. The ALS features are ideal for use in notebook PCs, LCD monitors, flat-panel televisions, and cell phones. The proximity function is targeted specifically towards near field proximity applications. In cell phones, the proximity detection can detect when the user positions the phone close to their ear. The device is fast enough to provide proximity information at a high repetition rate needed when answering a phone call. This provides both improved "green" power saving capability and the added security to lock the computer when the user is not present. The addition of the micro-optics lenses within the module, provide highly efficient transmission and reception of infrared energy which lowers overall power dissipation. Ordering Information Part Number Packaging Quantity APDS-9900 Tape & Reel 2500 per reel APDS-9901 Tape & Reel 2500 per reel * Ambient Light Sensing (ALS) - Approximates Human Eye Response - Programmable Interrupt Function with Upper and Lower Threshold - Up to 16-Bit Resolution - High Sensitivity Operates Behind Darkened Glass - Up to 1,000,000:1 Dynamic Range * Proximity Detection - Fully Calibrated to 100 mm Detection - Integrated IR LED and Synchronous LED Driver - Eliminates "Factory Calibration" of Prox - Covers a 2000:1 Dynamic Range * Programmable Wait Timer - Wait State Power - 70 A Typical - Programmable from 2.72 ms to > 6 Sec * I2C Interface Compatible - Up to 400 kHz (I2C Fast-Mode) - Dedicated Interrupt Pin * Sleep Mode Power - 2.5 A Typical * Small Package L3.94 x W2.36 x H1.35 mm Applications * * * * * * Cell Phone Backlight Dimming Cell Phone Touch-screen Disable Notebook/Monitor Security Automatic Speakerphone Enable Automatic Menu Pop-up Digital Camera Eye Sensor 8 - VDD 1 - SDA 7 - SCL 2 - INT 6 - GND 3 - LDR 5 - LED A 4 - LED K Functional Block Diagram VDD Interrupt INT Upper Threshold ALS ADC Data SCL Lower Threshold I2C Interface Ch0 Ch1 Upper Threshold Prox Detect ADC LED A SDA Data Lower Threshold Prox IR LED LED K LED Regulated Constant Current Sink Control Logic LDR GND Detailed Description The APDS-9900/9901 light-to-digital device provides on-chip Ch0 and Ch1 diodes, integrating amplifiers, ADCs, accumulators, clocks, buffers, comparators, a state machine and an I2C interface. Each device combines one Ch0 photodiode (visible plus infrared) and one Ch1 infrared-responding (IR) photodiode. Two integrating ADCs simultaneously convert the amplified photodiode currents to a digital value providing up to 16-bits of resolution. Upon completion of the conversion cycle, the conversion result is transferred to the Ch0 and CH1 data registers. This digital output can be read by a microprocessor where the illuminance (ambient light level) in Lux is derived using an empirical formula to approximate the human eye response. Communication to the device is accomplished through a fast (up to 400 kHz), two-wire I2C serial bus for easy connection to a microcontroller or embedded controller. The digital output of the APDS-9900/9901 device is inherently more immune to noise when compared to an analog interface. The APDS-9900/9901 provides a separate pin for level-style interrupts. When interrupts are enabled and a pre-set value is exceeded, the interrupt pin is asserted and remains asserted until cleared by the controlling firmware. 2 The interrupt feature simplifies and improves system efficiency by eliminating the need to poll a sensor for a light intensity or proximity value. An interrupt is generated when the value of an ALS or proximity conversion exceeds either an upper or lower threshold. Additionally, a programmable interrupt persistence feature allows the user to determine how many consecutive exceeded thresholds are necessary to trigger an interrupt. Interrupt thresholds and persistence settings are configured independently for both ALS and proximity. Proximity detection is fully provided with an 850 nm IR LED. An internal LED driver (LDR) pin, is jumper connected to the LED cathode (LED K) to provide a factory calibrated proximity of 100 +/- 20 mm. This is accomplished with a proprietary current calibration technique that accounts for all variances in silicon, optics, package and most importantly IR LED output power. This will eliminate or greatly reduce the need for factory calibration that is required for most discrete proximity sensor solutions. While the APDS9900/9901 is factory calibrated at a given pulse count, the number of proximity LED pulses can be programmed from 1 to 255 pulses, which will allow greater proximity distances to be achieved. Each pulse has a 16 s period. I/O Pins Configuration PIN NAME TYPE DESCRIPTION 1 SDA I/O I2C serial data I/O terminal - serial data I/O for I2C. 2 INT O Interrupt - open drain. 3 LDR I LED driver for proximity emitter - up to 100 mA, open drain. 4 LEDK O LED Cathode, connect to LDR pin in most systems to use internal LED driver circuit 5 LEDA I LED Anode, connect to VBATT on PCB 6 GND 7 SCL 8 VDD Power supply ground. All voltages are referenced to GND. I I2C serial clock input terminal - clock signal for I2C serial data. Power Supply voltage. Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) Parameter Symbol Power Supply voltage VDD Digital voltage range Min Max Units Test Conditions 3.8 V [1] -0.5 3.8 V Digital output current IO -1 20 mA Storage temperature range Tstg -40 85 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Note: 1. All voltages are with respect to GND. Recommended Operating Conditions Parameter Symbol Min Operating Ambient Temperature TA -30 Supply voltage VDD 2.5 Supply Voltage Accuracy, VDD total error including transients LED Supply Voltage VBATT Available Options Part Number Interface Description APDS-9901 I2C VBUS = VDD Interface APDS-9900 I2C 1.8V VBUS Interface 3 Typ 3.0 Max Units 85 C 3.6 V -3 +3 % 2.5 4.5 V Operating Characteristics, VDD = 3 V, TA = 25 C (unless otherwise noted) Parameter Symbol Supply current [1] IDD Min Typ Max Units Test Conditions 175 250 A Active (ATIME=0xdb, 100ms) 70 Wait Mode 2.5 INT SDA output low voltage VOL Leakage current, SDA, SCL, INT pins ILEAK Leakage current, LDR pin ILEAK SCL, SDA input high voltage VIH SCL, SDA input low voltage, VIL Oscillator frequency fosc 4.0 Sleep Mode 0 0.4 0 0.6 -5 5 A 10 A 0.7 VBUS 1.25 0.3 VBUS 0.54 705 750 795 V 3 mA sink current 6 mA sink current V APDS-9901 APDS-9900 V APDS-9901 APDS-9900 kHz PON = 1 Note: 1. The power consumption is raised by the programmed amount of Proximity LED Drive during the 8 us the LED pulse is on. The nominal and maximum values are shown under Proximity Characteristics. There the IDD supply current is IDD Active + Proximity LED Drive programmed value. ALS Characteristics, VDD = 3 V, TA = 25 C, Gain = 16, AEN = 1 (unless otherwise noted) Parameter Channel Min Typ Max Units Test Conditions Dark ALS ADC count value Ch0 0 1 5 counts Ee = 0, AGAIN = 120x, ATIME = 0xDB(100ms) Ch1 0 1 5 2.58 2.72 2.90 ms ATIME = 0xff 256 steps Full Scale ADC Counts per Step 1023 counts Full scale ADC count value 65535 counts ATIME = 0xC0 6000 counts p = 640 nm, Ee = 56 W/cm2, ATIME = 0xF6 (27 ms), GAIN = 16x ALS ADC Integration Time Step Size ALS ADC Number of Integration Steps ALS ADC count value 1 Ch0 4000 5000 4000 5000 Ch1 Ch0 790 Ch1 ALS ADC count value ratio: Ch1/Ch0 Irradiance Responsivity: Re Gain scaling, relative to 1x gain setting p = 850 nm, Ee = 79 W/cm2, ATIME = 0xF6 (27 ms), GAIN = 16x 6000 2800 10.8 15.8 20.8 41 56 68 Ch0 29.1 Ch1 4.6 Ch0 22.8 Ch1 12.7 % p = 640 nm, ATIME = 0xF6 (27 ms) p = 850 nm, ATIME = 0xF6 (27 ms) Counts per (W/ cm2) p = 640 nm, ATIME = 0xF6 (27 ms) p = 850 nm, ATIME = 0xF6 (27 ms) -5 5 % 8x -5 5 16x -5 5 120x Notes: 1. Optical measurements are made using small-angle incident radiation from light-emitting diode optical sources. Visible 640 nm LEDs and infrared 850 nm LEDs are used for final product testing for compatibility with high-volume production. 2. The 640 nm irradiance Ee is supplied by an AlInGaP light-emitting diode with the following characteristics: peak wavelength = 640 nm and spectral halfwidth 1/2 = 17 nm. 3. The 850 nm irradiance Ee is supplied by a GaAs light-emitting diode with the following characteristics: peak wavelength = 850 nm and spectral halfwidth 1/2 = 40 nm. 4. The specified light intensity is 100% modulated by the pulse output of the device so that during the pulse output low time, the light intensity is at the specified level, and zero otherwise. 4 Proximity Characteristics, VDD = 3 V, TA = 25 C, PGAIN = 1, PEN = 1 (unless otherwise noted) Parameter Min Typ Max Units Test Conditions IDD Supply current - LDR Pulse On 3 mA ADC Conversion Time Step Size 2.72 ms PTIME = 0xff steps PTIME = 0xff 1023 counts PTIME = 0xff 255 pulses ADC Number of Integration Steps 1 Full Scale ADC Counts Proximity IR LED Pulse Count 0 16.3 s Proximity Pulse - LED On Time 7.2 s Proximity LED Drive 100 mA Proximity Pulse Period Proximity ADC count value, no object Proximity ADC count value, 100 mm distance object PDRIVE = 0 50 PDRIVE = 1 25 PDRIVE = 2 12.5 PDRIVE = 3 100 LED driving 8 pulses, PDRIVE = 0, open view (no glass) and no reflective object above the module. 416 520 624 counts Reflecting object - 73 mm x 83 mm Kodak 90% grey card, 100mm distance, LED driving 8 pulses, PDRIVE = 0, open view (no glass) above the module. Min Typ Max Units Test Conditions 1.4 1.5 IR LED Characteristics, VDD = 3 V, TA = 25C Parameter Forward Voltage, VF V IF = 20 mA Reverse Voltage, VR 5.0 V IR = 10 A Radiant Power, PO 4.5 mW IF = 20 mA Peak Wavelength, P 850 nm IF = 20 mA Spectrum Width, Half Power, 40 nm IF = 20 mA Optical Rise Time, TR 20 ns IFP = 100 mA Optical Fall Time, TF 20 ns IFP = 100 mA Wait Characteristics, VDD = 3 V, TA = 25 C, Gain = 16, WEN = 1 (unless otherwise noted) Parameter Min Wait Step Size Wait Number of Step 5 ISINK Sink current @ 600 mV, LDR Pin Typ Max 2.72 1 256 Units Test Conditions ms WTIME = 0xff steps Characteristics of the SDA and SCL bus lines, VDD = 3 V, TA = 25 C (unless otherwise noted) STANDARD-MODE Parameter Symbol SCL clock frequency fSCL Hold time (repeated) START condition. After this period, the first clock pulse is generated FAST-MODE Min. Max. Min. Max. Units 0 100 0 400 kHz tHD;STA 4.0 - 0.6 - s LOW period of the SCL clock tLOW 4.7 - 1.3 - s HIGH period of the SCL clock tHIGH 4.0 - 0.6 - s Set-up time for a repeated START condition tSU;STA 4.7 - 0.6 - s Data hold time tHD;DAT 0 - 0 - ns Data set-up time tSU;DAT 250 - 100 - ns Rise time of both SDA and SCL signals tr 20 1000 20 300 ns Fall time of both SDA and SCL signals tf 20 300 20 300 ns Set-up time for STOP condition tSU;STO 4.0 - 0.6 - s Bus free time between a STOP and START condition tBUF 4.7 - 1.3 - s Capacitive load for each bus line Cb - 400 - 400 pF Noise margin at the LOW level for each connected device (including hysteresis) VnL 0.1VBUS - 0.1VBUS - V Noise margin at the HIGH level for each connected device (including hysteresis) VnH 0.2VBUS - 0.2VBUS - V Specified by design and characterization; not production tested. SDA tLOW tf tf tSU;DAT tr tHD;STA tSP tr tBUF SCL S tHD;STA SCL SDA Figure 1. I2C Bus Timing Diagram 6 tHD;DAT tHIGH tSU;STA Sr tSU;STO P S MSC610 9000 8000 1.0 7000 Ch 0 0.8 Avg Sensor LUX NORMALIZED RESPONSITIVITY 1.2 0.6 0.4 Ch 1 5000 4000 3000 2000 0.2 1000 0.0 300 400 500 600 700 800 WAVELENGTH (nm) 900 1000 0 1100 1000 2000 3000 4000 5000 Meter LUX 6000 7000 8000 0.1 1600 1400 0.08 Avg Sensor LUX 1200 1000 800 600 400 0.06 0.04 0.02 200 0 0 Figure 3a. ALS Sensor LUX vs. Meter LUX using Fluorescent Light Figure 2. Spectral Response Avg Sensor LUX 6000 0 300 600 900 Meter LUX 1200 0 1500 Figure 3b. ALS Sensor LUX vs. Meter LUX using Incandescent Light 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 Meter LUX 0.1 Figure 3c. ALS Sensor LUX vs. Meter LUX using Low Lux Fluorescent Light 1.2 NORMALIZED IDD @ 3V NORMALIZED IDD @ 3V 25C 1.1 1.0 0.9 0.8 2.4 2.6 2.8 3 VDD (V) 3.2 3.4 3.6 3.8 NORMALIZED RESPONSITIVITY Figure 4a. Normalized IDD vs. VDD 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -100 -80 -60 -40 -20 0 20 ANGLE (DEG) 1.0 0.9 0.8 -60 -40 -20 0 20 40 TEMPERATURE (C) Figure 4b. Normalized IDD vs. Temperature 40 60 Figure 5. Normalized ALS Response vs. Angular Displacement 7 1.1 80 100 60 80 100 PRINCIPLES OF OPERATION System State Machine Ch0 and Ch1 Diodes The APDS-9900/9901 provides control of ALS, proximity detection and power management functionality through an internal state machine. After a power-on-reset, the device is in the sleep mode. As soon as the PON bit is set, the device will move to the start state. It will then continue through the Prox, Wait and ALS states. If these states are enabled, the device will execute each function. If the PON bit is set to a 0, the state machine will continue until all conversions are completed and then go into a low power sleep mode. Conventional silicon detectors respond strongly to infrared light, which the human eye does not see. This can lead to significant error when the infrared content of the ambient light is high (such as with incandescent lighting) due to the difference between the silicon detector response and the brightness perceived by the human eye. Sleep PON = 1 (rO:b0) PON = 0 (rO:b0) Start Prox ALS ALS Operation Wait Figure 6. Simplified State Diagram NOTE: In this document, the nomenclature uses the bit field name in italics followed by the register number and bit number to allow the user to easily identify the register and bit that controls the function. For example, the power on (PON) is in register 0, bit 0. This is represented as PON (r0:b0). Ch0 ADC Ch0 ALS Control Ch1 ADC Ch1 Figure 7. ALS Operation 8 Ch0 Data Ch1 Data This problem is overcome in the APDS-9900/9901 through the use of two photodiodes. One of the photodiodes, referred to as the Ch0 channel, is sensitive to both visible and infrared light while the second photodiode is sensitive primarily to infrared light. Two integrating ADCs convert the photodiode currents to digital outputs. The CH1DATA digital value is used to compensate for the effect of the infrared component of light on the CH0DATA digital value. The ADC digital outputs from the two channels are used in a formula to obtain a value that approximates the human eye response in units of Lux. The ALS engine contains ALS gain control (AGAIN) and two integrating analog-to-digital converters (ADC) for the Ch0 and Ch1 photodiodes. The ALS integration time (ALSIT) impacts both the resolution and the sensitivity of the ALS reading. Integration of both channels occurs simultaneously and upon completion of the conversion cycle, the results are transferred to the Ch0 and CH1 data registers (CDATAx and IRDATAx). This data is also referred to as channel "count". The transfers are double-buffered to ensure that invalid data is not read during the transfer. After the transfer, the device automatically moves to the next state in accordance with the configured state machine. CDATAH (r0 x 15), CDATAL (r0 x 14) ATIME (r0 x 01), 0 x ff to 0 x 00 AGAIN (r0 x OF, b1:0), 1x, 8x, 16x, 120 x Gain IRDATAH (r0 x 17), IRDATAL (r0 x 16) The ALS Timing register value (ATIME) for programming the integration time (ALSIT) is a 2's complement values. The ALS Timing register value can be calculated as follows: ATIME = 256 - ALSIT / 2.72 ms Inversely, the integration time can be calculated from the register value as follows: ALSIT = 2.72 ms * (256 - ATIME) For example, if a 100 ms integration time is needed, the device needs to be programmed to: ATIME = 256 - (100 / 2.72) = 256 - 37 = 219 = 0xDB Conversely, the programmed value of 0xC0 would correspond to: ALSIT = (256 - 0xC0) * 2.72 =64 * 2.72 = 172 ms. Note: 2.72 ms can be estimated as 87 / 32. Multiply by 87 the shift by 5 bits. Calculating ALS Lux Definition: CH0DATA = 256 * CDATAH (r0x15) + CDATAL (r0x14) CH1DATA = 256 * IRDATAH (r0x17) + IRDATAL (r0x16) IAC = IR Adjusted Count LPC = Lux per Count ALSIT = ALS Integration Time (ms) AGAIN = ALS Gain DF = Device Factor, DF = 52 for APDS-9900/9901 GA = Glass (or Lens) Attenuation Factor B, C, D - Coefficients Lux Equation: IAC1 = CH0DATA - B x CH1DATA IAC2 = C x CH0DATA - D x CH1DATA IAC = Max (IAC1, IAC2, 0) LPC = GA x DF / (ALSIT x AGAIN) Lux = IAC x LPC Coefficients in open air: GA = 0.48 B = 2.23 C = 0.7 D = 1.42 Sample Lux Calculation in Open Air Assume the following constants: ALSIT = 400 AGAIN = 1 LPC = GA x DF / (ALSIT x AGAIN) LPC = 0.48 x 52 / (400 x 1) LPC = 0.06 Assume the following measurements: CH0DATA = 5000 CH1DATA = 525 Then: IAC1 = 5000 - 2.23 x 525 = 3829 IAC2 = 0.7 x 5000 - 1.42 x 525 = 2755 IAC = Max(3829, 2755, 0) = 3829 Lux: Lux = IAC X LPC Lux = 3829 X 0.06 Lux = 230 Note: please refer to application note for coefficient GA, B, C and D calculation with window. 9 Recommend ALS Operations Proximity Detection Proximity sensing uses an internal IR LED light source to emit light which is then viewed by the integrated light detector to measure the amount of reflected light when an object is in the light path. The amount of light detected from a reflected surface can then be used to determine an object's proximity to the sensor. The APDS-9900/9901 is factory calibrated to meet the requirement of proximity sensing of 100+/- 20 mm, thus eliminating the need for factory calibration of the end equipment. When the APDS9900/9901 is placed behind a typical glass surface, the proximity detection achieved is around 25 to 40 mm, thus providing an ideal touch-screen disable. 10000 1000 50 LUX 100 , 1x ms x 10 1 s, 50 m 0.1 s 0m 0.01 40 1 10 100 6x s, 1 s, 8 m 50 x m 50 120 0x , 12 1000 Counts Figure 8. Gain and Integration Time to Lux without IR 10000 100000 With the programming versatility of the integration time and gain, it can be difficult to understand when to use the different modes. Figure 8 shows a log-log plot of the Lux vs. integration time and gain with a spectral factor of unity and no IR present. The maximum illuminance which can be measured is ~10k Lux with no IR present. The intercept with a count of 1 shows the resolution of each setting. The Lux values in the table increase as the SF increases (spectral attenuation increases). For example, if a 10% transmissive glass is used, the Lux values would all be multiplied by 10. The Lux values in the table decrease as the IR Factor decreases. For example, with a 10% IR Factor, which corresponds to a strong incandescent light, the Lux value would need to be divided by 10. There are many factors that will impact the decision on which value to use for integration time and gain. One of the first factors is 50/60 Hz ripple rejection for fluorescent lighting. The programmed value needs to be multiples of 10/8.3 ms or the half cycle time. Both frequencies can be rejected with a programmed value of 50 ms (ATIME = 0xED). With this value, the resolution will be 1.3 Lux per count. If higher resolution is needed, a longer integration time may be needed. In this case, the integration time should be programmed in multiples of 50. The light level is the next determining factor for configuring device settings. Under bright conditions, the count will be fairly high. If a low light measurement is needed, a higher gain and/or longer integration time will be needed. As a general rule, it is recommended to have a Ch0 channel count of at least 10 to accurately apply the Lux equation. The digital accumulation is limited to 16 bits, which occurs at an integration time of 173 ms. This is the maximum recommended programmed integration time before increasing the gain. (150 ms is the maximum to reduce the fluorescent ripple.) 10 The APDS-9900/9901 has controls for the number of IR pulses (PPCOUNT), the integration time (PTIME), the LED drive current (PDRIVE) and the photodiode configuration (PDIODE). At the end of the integration cycle, the results are latched into the proximity data (PDATA) register. The LED drive current is controlled by a regulated current sink on the LDR pin. This feature eliminates the need to use a current limiting resistor to control LED current. The LED drive current can be configured for 12.5 mA, 25 mA, 50 mA, or 100 mA. For higher LED drive requirements, an external P type transistor can be used to control the LED current. The number of LED pulses can be programmed to a value of 1 to 255 pulses as needed. Increasing the number of LED pulses at a given current will increase the sensor sensitivity. Sensitivity grows by the square root of the number of pulses. Each pulse has a 16 mS period. The proximity integration time (PTIME) is the period of time that the internal ADC converts the analog signal to a digital count. It is recommend that this be set to a minimum of PTIME = 0xFF or 2.72 ms. Add IR + Background LED On Subtract Background LED Off 16 s IRLED Pulses Figure 9. Proximity IR LED Waveform Optical Design Considerations The APDS-9900/9901 simplifies the optical system design by eliminating the need for light pipes and improves system optical efficiency by providing apertures and package shielding which will reduce crosstalk when placed in the final system. By reducing the IR LED to glass surface crosstalk, proximity performance is greatly improved and enables a wide range of cell phone applications utilizing the APDS-9900/9901. The module package design has been optimized for minimum package foot print and short distance proximity of 100 mm typical. The spacing between the glass surface and package top surface is critical to controlling the crosstalk. If the package to top surface spacing gap, window thickness and transmittance are met, there should be no need to add additional components (such as a barrier) between the LED and photodiode. Thus with some simple mechanical design implementations, the APDS-9900/9901 will perform well in the end equipment system. The APDS-9900/9901 is available in a low profile package that contains optics which provides optical gain on botht the LED and the sensor side of the package. The device has a package Z height of 1.35 mm and will support air gap of < = 0.5 mm between the glass and the package. The assumption of the optical system level design is that glass surface above the module is < = to 1.0 mm. By integrating the micro-optics in the package, the IR energy emitted can be reduced thus conserving the precious battery life in the application. The system designer has the ability to optimize their designs for slim form factor Z height as well as improve the proximity sensing, save battery power and disable the touch screen in a cellular phone. APDS-9900/9901 Module Optimized design parameters * Window thickness, t 1.0 mm * Air gap, g 0.5 mm * Assuming window IR transmittance 90% Plastic/Glass Window Windows Thickness, t Air Gap, g APDS-9900/9901 Figure 10. Proximity Detection 1200 1200 6P (100mA) 1000 4P (100mA) 800 16P (100mA) 8P (50mA) 600 PS COUNT PS COUNT 1000 8P (100mA) 800 400 200 0 600 400 200 0 2 4 6 8 10 DISTANCE (cm) 12 14 Figure 11a. PS Output vs. Distance, at Various Pulse number (LED drive Current). No glass in front of the module, 18% Kodak Grey Card. 11 4P (100mA) 6P (100mA) 8P (100mA) 16P (100mA) 8P (50mA) 16 0 0 2 4 6 8 10 12 DISTANCE (cm) 14 16 18 Figure 11b. PS Output vs. Distance, at Various Pulse number (LED drive Current). No glass in front of the module, 90% Kodak Grey Card. 20 Interrupts The interrupt feature of the APDS-9900/9901 simplifies and improves system efficiency by eliminating the need to poll the sensor for a light intensity or proximity value. The interrupt mode is determined by the PIEN or AIEN field in the ENABLE register. The APDS-9900/9901 implements four 16-bit-wide interrupt threshold registers that allow the user to define thresholds above and below a desired light level. For ALS, an interrupt can be generated when the ALS Ch0 data (CDATA) exceeds the upper threshold value (AIHTx) or falls below the lower threshold (AILTx). For proximity, Prox Integration Prox ADC an interrupt can be generated when the proximity data (PDATA) exceeds the upper threshold value (PIHTx) or falls below the lower threshold (PILTx). To further control when an interrupt occurs, the APDS9900/9901 provides an interrupt persistence feature. This feature allows the user to specify a number of conversion cycles for which an event exceeding the ALS interrupt threshold must persist (APERS) or the proximity interrupt threshold must persist (PPERS) before actually generating an interrupt. Refer to the register descriptions for details on the length of the persistence. PIHTH (r0 x OB), PIHTL (r0 x OA) PPERS (r0 x OC, b7:4) Upper Limit Prox Persistence Prox Data Lower Limit PILTH (r09), PIHTL (r08) Ch0 ADC Ch0 AIHTH (r07), AIHTL (r06) APERS (r0 x OC, b3:0) Upper Limit ALS Persistence Ch0 Data Lower Limit Ch1 Ch1 ADC Ch1 Data AILTH (r05), AILTL (r04) Figure 12. Programmable Interrupt 12 State Diagram The following shows a more detailed flow for the state machine. The device starts in the sleep mode. The PON bit is written to enable the device. If the PEN bit is set, the state machine will step through the proximity states of proximity accumulate and then proximity ADC conversion. As soon as the conversion is complete, the state machine will move to the following state. When AEN bit is set, the state machine will step through the ALS states of ALS accumulate and then ALS ADC conversion. In this case, a minimum of 1 integration time step should be programmed. The ALS state machine will continue until it reaches the terminal count at which point the data will be latched in the ALS register and the interrupt set, if enabled. If the WEN bit is set, the state machine will then cycle through the wait state. If the WLONG bit is set, the wait cycles are extended by 12x over normal operation. When the wait counter terminates, the state machine will step to the ALS state. Power Management Up to 255 LED Pulses Pulse Frequency: 60 kHz Time: 16.3 s - 4.2 ms Maximum 4.2 ms Power consumption can be controlled through the use of the wait state timing since the wait state consumes only 70 A of power. The following shows an example of using the power management feature to achieve an average power consumption of 158 A of current with 4 - 100 mA pulses of proximity detection and 50 ms of ALS detection. Up to 255 steps Step: 2.72 ms Time: 2.72 ms - 696 ms 120 Hz Minimum - 8 ms 100 Hz Minimum - 10 ms Sleep PON = 1 PON = 0 Start Prox Accum ALS PEN = 1 Prox Check ALS Check Prox ADC AEN = 1 Wait Check Up to 255 steps Step: 2.72 ms Time: 2.72 ms - 696 ms Recommened - 2.72 ms 1023 Counts ALS Delay WEN = 1 WLONG = 0 Counts up to 256 steps Step: 2.72 ms Time: 2.72 ms - 696 ms Minimum - 2.72 ms Wait WLONG = 1 Counts up to 256 steps Step: 32.64 ms Time: 32.64 ms - 8.35 s Minimum - 32.64 ms Figure 13. Extended State Diagram 4 IRLED Pulses Prox Accum Prox ADC WAIT ALS 64 s (32 s LED On Time) 2.72 ms 47 ms 50 ms Example: 100 ms Cycle Time State Duration (ms) Prox Accum (LED On) 0.064 (0.032) Prox ADC 2.72 WAIT 47 ALS 50 Current (mA) 100 0.175 0.070 0.175 Avg = ((0.032 x 100) + (2.72 x 0.175) + (47 x 0.070) + (50 x 0.175)) / 100 = 158 A Figure 14. Power Consumption Calculations 13 Basic Software Operation The following pseudo-code shows how to do basic initialization of the APDS-9900/9901. uint8 ATIME, PIME, WTIME, PPCOUNT; ATIME = 0xff; // 2.7 ms - minimum ALS integration time WTIME = 0xff; // 2.7 ms - minimum Wait time PTIME = 0xff; // 2.7 ms - minimum Prox integration time PPCOUNT = 1; // Minimum prox pulse count WriteRegData(0, 0); //Disable and Powerdown WriteRegData (1, ATIME); WriteRegData (2, PTIME); WriteRegData (3, WTIME); WriteRegData (0xe, PPCOUNT); uint8 PDRIVE, PDIODE, PGAIN, AGAIN; PDRIVE = 0; //100mA of LED Power PDIODE = 0x20; // CH1 Diode PGAIN = 0; //1x Prox gain AGAIN = 0; //1x ALS gain WriteRegData (0xf, PDRIVE | PDIODE | PGAIN | AGAIN); uint8 WEN, PEN, AEN, PON; WEN = 8; // Enable Wait PEN = 4; // Enable Prox AEN = 2; // Enable ALS PON = 1; // Enable Power On WriteRegData (0, WEN | PEN | AEN | PON); // WriteRegData(0,0x0f ); Wait(12); //Wait for 12 ms int CH0_data, CH1_data, Prox_data; CH0_data = Read_Word(0x14); CH1_data = Read_Word(0x16); Prox_data = Read_Word(0x18); WriteRegData(uint8 reg, uint8 data) { m_I2CBus.WriteI2C(0x39, 0x80 | reg, 1, &data); } uint16 Read_Word(uint8 reg); { uint8 barr[2]; m_I2CBus.ReadI2C(0x39, 0xA0 | reg, 2, ref barr); return (uint16)(barr[0] + 256 * barr[1]); } 14 I2C Protocol written is the command byte followed by reading a series of bytes. If a read command is issued, the register address from the previous command will be used for data access. Likewise, if the MSB of the command is not set, the device will write a series of bytes at the address stored in the last valid command with a register address. The command byte contains either control information or a 5 bit register address. The control commands can also be used to clear interrupts. For a complete description of I2C protocols, please review the I2C Specification at: http://www.NXP. com Interface and control of the APDS-9900/9901 is accomplished through an I2C serial compatible interface (standard or fast mode) to a set of registers that provide access to device control functions and output data. The device supports a single slave address of 0x39 hex using 7 bit addressing protocol. (Contact factory for other addressing options.) The I2C standard provides for three types of bus transaction: read, write and a combined protocol. During a write operation, the first byte written is a command byte followed by data. In a combined protocol, the first byte Start and Stop conditions SDA SCL S P START condition STOP condition Data transfer on I2C-bus P SDA MSB SCL S or Sr 1 acknowledgement signal from slave 2 7 START or repeated START condition 8 MSB MSB 1 9 ACK byte complete, interrupt within slave 2 3 to 8 9 ACK acknowledgement signal from receiver 1 2 3 to 8 clock line held LOW while interrupts are serviced A complete data transfer SDA SCL 1-7 8 9 1-7 8 9 1-7 8 9 P S START condition 15 ADDRESS R/W ACK DATA ACK DATA ACK STOP condition MBC604 9 ACK Sr Sr or P STOP or repeated START condition A N P R S Sr W ... Acknowledge (0) Not Acknowledged (1) Stop Condition Read (1) Start Condition Repeated Start Condition Write (0) Continuation of protocol Master-to-Slave Slave-to-Master 1 7 1 1 8 1 8 1 1 S Slave Address W A Command Code A Data A P 1 8 1 8 1 1 A Data Low A Data High A P I2C Write Protocol 1 7 S Slave Address 1 1 8 1 1 W A Command Code A P I2C Write Protocol (Clear Interrupt) 1 7 1 1 8 S Slave Address W A Command Code I2C Write Word Protocol 1 7 1 1 8 1 1 7 1 1 8 1 1 S Slave Address W A Command Code A Sr Slave Address R A Data N P I2C Read Protocol - Combined Format 1 7 1 1 8 1 1 7 1 1 8 1 S Slave Address W A Command Code A Sr Slave Address R A Data Low A I2C Read Word Protocol 16 8 1 1 Data High N P Register Set The APDS-9900/9901 is controlled and monitored by data registers and a command register accessed through the serial interface. These registers provide for a variety of control functions and can be read to determine results of the ADC conversions. ADDRESS RESISTER NAME R/W REGISTER FUNCTION Reset Value - COMMAND W Specifies register address 0x00 0x00 ENABLE R/W Enable of states and interrupts 0x00 0x01 ATIME R/W ALS ADC time 0x00 0x02 PTIME R/W Proximity ADC time 0xFF 0x03 WTIME R/W Wait time 0xFF 0x04 AILTL R/W ALS interrupt low threshold low byte 0x00 0x05 AILTH R/W ALS interrupt low threshold hi byte 0x00 0x06 AIHTL R/W ALS interrupt hi threshold low byte 0x00 0x07 AIHTL R/W ALS interrupt hi threshold hi byte 0x00 0x08 PILTL R/W Proximity interrupt low threshold low byte 0x00 0x09 PILTH R/W Proximity interrupt low threshold hi byte 0x00 0x0A PIHTL R/W Proximity interrupt hi threshold low byte 0x00 0x0B PIHTH R/W Proximity interrupt hi threshold hi byte 0x00 0x0C PERS R/W Interrupt persistence filters 0x00 0x0D CONFIG R/W Configuration 0x00 0x0E PPCOUNT R/W Proximity pulse count 0x00 0x0F CONTROL R/W Gain control register 0x00 0x11 REV R Revision Number Rev 0x12 ID R Device ID ID 0x13 STATUS R Device status 0x00 0x14 CDATAL R Ch0 ADC low data register 0x00 0x15 CDATAH R Ch0 ADC high data register 0x00 0x16 IRDATAL R Ch1 ADC low data register 0x00 0x17 IRDATAH R Ch1 ADC high data register 0x00 0x18 PDATAL R Proximity ADC low data register 0x00 0x19 PDATAH R Proximity ADC high data register 0x00 The mechanics of accessing a specific register depends on the specific protocol used. See the section on I2C protocols on the previous pages. In general, the COMMAND register is written first to specify the specific control/status register for following read/write operations. 17 Command Register The command registers specifies the address of the target register for future write and read operations. 7 COMMAND 6 CMD 5 4 3 TYPE 2 1 0 ADD - FIELD BITS DESCRIPTION COMMAND 7 Select Command Register. Must write as 1 when addressing COMMAND register. TYPE 6:5 Selects type of transaction to follow in subsequent data transfers: FIELD VALUE INTEGRATION TIME 00 Repeated Byte protocol transaction 01 Auto-Increment protocol transaction 10 Reserved - Do not use 11 Special function - See description below Byte protocol will repeatedly read the same register with each data access. Block protocol will provide auto-increment function to read successive bytes. ADD 4:0 Address register/special function register. Depending on the transaction type, see above, this field either specifies a special function command or selects the specific control-status-register for following write or read transactions: FIELD VALUE READ VALUE 00000 Normal - no action 00101 Proximity interrupt clear 00110 ALS interrupt clear 00111 Proximity and ALS interrupt clear other Reserved - Do not write ALS/Proximity Interrupt Clear. Clears any pending ALS/Proximity interrupt. This special function is self clearing. Enable Register (0x00) The ENABLE register is used primarily to power the APDS-9900/9901 device up and down as shown in Table 4. ENABLE 7 6 5 4 3 2 1 0 Address Reserved Reserved PIEN AIEN WEN PEN AEN PON 0x00 FIELD BITS DESCRIPTION Reserved 7:6 Reserved. Write as 0. PIEN 5 Proximity Interrupt Enable. When asserted, permits proximity interrupts to be generated. AIEN 4 ALS Interrupt Enable. When asserted, permits ALS interrupt to be generated. WEN 3 Wait Enable. This bit activates the wait feature. Writing a 1 activates the wait timer. Writing a 0 disables the wait timer. PEN 2 Proximity Enable. This bit activates the proximity function. Writing a 1 enables proximity. Writing a 0 disables proximity. AEN 1 ALS Enable. This bit actives the two channel ADC. Writing a 1 activates the ADC. Writing a 0 disables the ADC. PON 0 Power ON. This bit activates the internal oscillator to permit the timers and ADC channels to operate. Writing a 1 activates the oscillator. Writing a 0 disables the oscillator. Notes: 1. A 2.72 ms delay is automatically inserted prior to entering the ADC cycle, independent of the WEN bit. 2. Both AEN and PON must be asserted before the ADC channels will operate correctly. 3. During writes and reads over the I2C interface, this bit is overridden and the oscillator is enabled, independent of the state of PON. 4. A minimum interval of 2.72 ms must pass after PON is asserted before either proximity or an ALS can be initiated. This required time is enforced by the hardware in cases where the firmware does not provide it. 18 ALS Timing Register (0x01) The ALS timing register controls the integration time of the ALS Ch0 and Ch1 channel ADCs in 2.72 ms increments. FIELD BITS DESCRIPTION ATIME 7:0 VALUE CYCLES TIME (ALSIT) Max Count 0xff 1 2.72 ms 1023 0xf6 10 27.2 ms 10239 0xdb 37 100.64 ms 37887 0xc0 64 174.08 ms 65535 0x00 256 696.32 ms 65535 Proximity Time Control Register (0x02) The proximity timing register controls the integration time of the proximity ADC in 2.72 ms increments. It is recommended that this register be programmed to a value of 0xff (1 cycle, 1023 bits). FIELD BITS DESCRIPTION PTIME 7:0 VALUE CYCLES TIME Max Count 0xff 1 2.72 ms 1023 Wait Time Register (0x03) Wait time is set 2.72 ms increments unless the WLONG bit is asserted in which case the wait times are 12x longer. WTIME is programmed as a 2's complement number. FIELD BITS DESCRIPTION WTIME 7:0 REGISTER VALUE WALL TIME TIME (WLONG = 0) TIME (WLONG = 1) 0xff 1 2.72 ms 0.032 sec 0xb6 74 201.29 ms 2.37 sec 0x00 256 696.32 ms 8.19 sec Notes: 1. The Write Byte protocol cannot be used when WTIME is greater than 127. 2. The Proximity Wait Time Register should be configured before PEN and/or AEN is/are asserted. ALS Interrupt Threshold Register (0x04 - 0x07) The ALS interrupt threshold registers provides the values to be used as the high and low trigger points for the comparison function for interrupt generation. If the value generated by the ALS channel crosses below the low threshold specified, or above the higher threshold, an interrupt is asserted on the interrupt pin. REGISTER ADDRESS BITS DESCRIPTION AILTL 0x04 7:0 ALS Ch0 channel low threshold lower byte AILTH 0x05 7:0 ALS Ch0 channel low threshold upper byte AIHTL 0x06 7:0 ALS Ch0 channel high threshold lower byte AIHTH 0x07 7:0 ALS Ch0 channel high threshold upper byte Note: The Write Word protocol should be used to write byte-paired registers. 19 Proximity Interrupt Threshold Register (0x08 - 0x0B) The proximity interrupt threshold registers provide the values to be used as the high and low trigger points for the comparison function for interrupt generation. If the value generated by proximity channel crosses below the lower threshold specified, or above the higher threshold, an interrupt is signaled to the host processor. REGISTER ADDRESS BITS DESCRIPTION PILTL 0x08 7:0 Proximity ADC channel low threshold lower byte PILTH 0x09 7:0 Proximity ADC channel low threshold upper byte PIHTL 0x0A 7:0 Proximity ADC channel high threshold lower byte PIHTH 0x0B 7:0 Proximity ADC channel high threshold upper byte Persistence Register (0x0C) The persistence register controls the filtering interrupt capabilities of the device. Configurable filtering is provided to allow interrupts to be generated after each ADC integration cycle or if the ADC integration has produced a result that is outside of the values specified by threshold register for some specified amount of time. Separate filtering is provided for proximity and ALS functions. ALS interrupts are generated by looking only at the ADC integration results of channel 0. 7 6 PERS 5 4 3 PPERS 2 1 0 APERS 0x0c FIELD BITS DESCRIPTION PPERS 7:4 Proximity interrupt persistence. Controls rate of proximity interrupt to the host processor. APERS 20 3:0 FIELD VALUE MEANING INTERRUPT PERSISTENCE FUNCTION 0000 Every Every proximity cycle generates an interrupt 0001 1 1 consecutive proximity values out of range ... ... ... 1111 15 15 consecutive proximity values out of range Interrupt persistence. Controls rate of interrupt to the host processor. FIELD VALUE MEANING INTERRUPT PERSISTENCE FUNCTION 0000 Every Every ALS cycle generates an interrupt 0001 1 1 consecutive Ch0 channel values out of range 0010 2 2 consecutive Ch0 channel values out of range 0011 3 3 consecutive Ch0 channel values out of range 0100 5 5 consecutive Ch0 channel values out of range 0101 10 10 consecutive Ch0 channel values out of range 0110 15 15 consecutive Ch0 channel values out of range 0111 20 20 consecutive Ch0 channel values out of range 1000 25 25 consecutive Ch0 channel values out of range 1001 30 30 consecutive Ch0 channel values out of range 1010 35 35 consecutive Ch0 channel values out of range 1011 40 40 consecutive Ch0 channel values out of range 1100 45 45 consecutive Ch0 channel values out of range 1101 50 50 consecutive Ch0 channel values out of range 1110 55 55 consecutive Ch0 channel values out of range 1111 60 60 consecutive Ch0 channel values out of range Configuration Register (0x0D) The configuration register sets the wait long time. 7 6 5 CONFIG 4 3 2 Reserved 1 0 WLONG Reserved 0x0D FIELD BITS DESCRIPTION Reserved 7:2 Reserved. Write as 0. WLONG 1 Wait Long. When asserted, the wait cycles are increased by a factor 12x from that programmed in the WTIME register. Reserved 0 Reserved. Write as 0. Proximity Pulse Count Register (0x0E) The proximity pulse count register sets the number of proximity pulses that will be transmitted. When proximity detection is enabled, a proximity detect cycle occurs after each ALS cycle. PPCOUNT defines the number of pulses to be transmitted at a 62.5 kHz rate. 7 6 PPCOUNT 5 4 3 2 1 0 PPCOUNT FIELD BITS DESCRIPTION PPCOUNT 7:0 Proximity Pulse Count. Specifies the number of proximity pulses to be generated. 21 0x0E Control Register (0x0F) The Gain register provides eight bits of miscellaneous control to the analog block. These bits typically control functions such as gain settings and/or diode selection. 7 CONTROL 6 5 PDRIVE 4 PDIODE FIELD BITS DESCRIPTION PDRIVE 7:6 LED Drive Strength. PDIODE PGAIN AGAIN 5:4 3:2 1:0 3 2 1 PGAIN FIELD VALUE LED STRENGTH 00 100 mA 01 50 mA 10 25 mA 11 12.5 mA 0 AGAIN 0x0F Proximity Diode Select. FIELD VALUE DIODE SELECTION 00 Reserved 01 Reserved 10 Proximity uses the Ch1 diode 11 Reserved Proximity Gain Control. FIELD VALUE Proximity GAIN VALUE 00 1X Gain 01 Reserved 10 Reserved 11 Reserved ALS Gain Control. FIELD VALUE ALS GAIN VALUE 00 1X Gain 01 8X Gain 10 16X Gain 11 120X Gain Revision number Register (0x11) The Revision number register provides the silicon revision number. The Rev ID is a read-only register whose value never changes. 7 6 5 4 REV ID FIELD BITS DESCRIPTION REV 7:0 Revision number identification 0x01 22 3 2 1 0 0x11 Device ID Register (0x12) The ID register provides the value for the part number. The ID register is a read-only register. 7 6 5 4 ID 3 2 1 0 Device ID FIELD BITS DESCRIPTION ID 7:0 Part number identification 0x12 0x29 = APDS-9900 0x20 = APDS-9901 Status Register (0x13) The Status Register provides the internal status of the device. This register is read only. STATUS 7 6 5 4 3 2 1 0 Reserved Reserved PINT AINT Reserved Reserved PVALID AVALID 0x13 FIELD BITS DESCRIPTION Reserved 7:6 Reserved. Write as 0. PINT 5 Proximity Interrupt. Indicates that the device is asserting a proximity interrupt. AINT 4 ALS Interrupt. Indicates that the device is asserting an ALS interrupt. Reserved 3:2 Reserved. Write as 0. PVALID 1 PS Valid. Indicates that the PS has completed an integration cycle. AVALID 0 ALS Valid. Indicates that the ALS Ch0/Ch1 channels have completed an integration cycle. ALS Data Registers (0x14 - 0x17) ALS Ch0 and CH1 data are stored as two 16-bit values. To ensure the data is read correctly, a two byte read I2C transaction should be utilized with a read word protocol bit set in the command register. With this operation, when the lower byte register is read, the upper eight bits are stored into a shadow register, which is read by a subsequent read to the upper byte. The upper register will read the correct value even if additional ADC integration cycles end between the reading of the lower and upper registers. REGISTER ADDRESS BITS DESCRIPTION CDATA 0x14 7:0 ALS Ch0 channel data low byte CDATAH 0x15 7:0 ALS Ch0 channel data high byte IRDATA 0x16 7:0 ALS Ch1 channel data low byte IRDATAH 0x17 7:0 ALS Ch1 channel data high byte Proximity DATA Register (0x18 - 0x19) Proximity data is stored as a 16-bit value. To ensure the data is read correctly, a two byte read I2C transaction should be utilized with a read word protocol bit set in the command register. With this operation, when the lower byte register is read, the upper eight bits are stored into a shadow register, which is read by a subsequent read to the upper byte. The upper register will read the correct value even if additional ADC integration cycles end between the reading of the lower and upper registers. REGISTER ADDRESS BITS DESCRIPTION PDATA 0x18 7:0 Proximity data low byte PDATAH 0x19 7:0 Proximity data high byte 23 Application Information: Hardware The application hardware circuit for using implementing an ALS and Proximity system solution is quite simple with the APDS-9900/9901 and is shown in following figure. The 1 F decoupling capacitors should be low ESR to reduce noise. It further recommended to maximize system performance the use of power and ground planes is recommended in the PCB. If mounted on a flexible circuit, the power and ground traces back to the PCB should be sufficiently wide enough to have a low resistance, such as < 1 ohm. VBUS VDD 1 F 10 k 10 k 10 k VDD MCU GPIO INT SCL SCL LDR APDS-9900/9901 LED K VBATT SDA LED A SDA GND Figure 15. Circuit implementation for ALS plus Proximity solution using the APDS-9900/9901 24 1 F Package Outline Dimensions 1 8 7 2 2 7 6 3 3 6 5 4 4 5 0 .05 0.25 (x6) 1.35 0.20 2.36 0.2 2.10 0.1 0.05 0.58 0.05 1.18 0.05 0.80 0.60 PINOUT 1 - SDA 2 - INT 3 - LDR 4 - LEDK 5 - LEDA 6 - GND 7 - SCL 8 - VDD PCB Pad Layout Suggested PCB pad layout guidelines for the Dual Flat No-Lead surface mount package are shown below. 0.60 0.80 0.72 (x8) 0.25 (x6) 0.60 Notes: all linear dimensions are in mm. 25 0.72 (x8) 1 3.73 0.1 8 1.34 .90 .05 3.94 0.2 O0 0 2.40 0.05 O1 0.05 0 .10 4 0.10 0.29 0.02 B0 O1 Unit Orientation .05 A 8 0.10 2.70 0.10 8 Max A0 All dimensions unit: mm Reel Dimensions 26 1.70 0.10 0 A 5.50 0.05 12 +0.30 -0.10 4.30 0.10 O1 . 50 2 0.05 1.75 0.10 Tape Dimensions K0 6 Max Moisture Proof Packaging All APDS-9900/9901 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC MSL 3. Units in A Sealed Mositure-Proof Package Package Is Opened (Unsealed) Environment less than 30 deg C, and less than 60% RH? Yes Yes No Baking Is Necessary Package Is Opened less than 168 hours? No Perform Recommended Baking Conditions Baking Conditions: No Recommended Storage Conditions: Package Temperature Time Storage Temperature 10 C to 30 C In Reel 60 C 48 hours Relative Humidity below 60% RH In Bulk 100 C 4 hours Time from unsealing to soldering: If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. Baking should only be done once. 27 After removal from the bag, the parts should be soldered within 168 hours if stored at the recommended storage conditions. If times longer than 168 hours are needed, the parts must be stored in a dry box Recommended Reflow Profile MAX 260 C R3 R4 TEMPERATURE (C) 255 230 217 200 180 150 120 R2 60 sec to 120 sec Above 217 C R1 R5 80 25 0 P1 HEAT UP Process Zone Heat Up Solder Paste Dry 50 100 150 P2 SOLDER PASTE DRY Symbol P1, R1 P2, R2 P3, R3 Solder Reflow P3, R4 Cool Down P4, R5 Time maintained above liquidus point , 217 C Peak Temperature Time within 5 C of actual Peak Temperature Time 25 C to Peak Temperature 200 P3 SOLDER REFLOW 250 P4 COOL DOWN 300 t-TIME (SECONDS) T Maximum T/time or Duration 25 C to 150 C 150 C to 200 C 200 C to 260 C 260 C to 200 C 200 C to 25 C > 217 C 260 C > 255 C 25 C to 260 C 3 C/s 100 s to 180s 3 C/s -6 C/s -6 C/s 60 s to 120 s - 20 s to 40 s 8 mins The reflow profile is a straight-line representation of a nominal temperature profile for a convective reflow solder process. The temperature profile is divided into four process zones, each with different T/time temperature change rates or duration. The T/time rates or duration are detailed in the above table. The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and component pins are heated to a temperature of 150 C to activate the flux in the solder paste. The temperature ramp up rate, R1, is limited to 3 C per second to allow for even heating of both the PC board and component pins. Process zone P2 should be of sufficient time duration (100 to 180 seconds) to dry the solder paste. The temperature is raised to a level just below the liquidus point of the solder. Process zone P3 is the solder reflow zone. In zone P3, the temperature is quickly raised above the liquidus point of solder to 260 C (500 F) for optimum results. The dwell time above the liquidus point of solder should be between 60 and 120 seconds. This is to assure proper coalescing of the solder paste into liquid solder and the formation of good solder connections. Beyond the recommended dwell time the intermetallic growth within the solder connections becomes excessive, resulting in the formation of weak and unreliable connections. The temperature is then rapidly reduced to a point below the solidus temperature of the solder to allow the solder within the connections to freeze solid. Process zone P4 is the cool down after solder freeze. The cool down rate, R5, from the liquidus point of the solder to 25 C (77 F) should not exceed 6 C per second maximum. This limitation is necessary to allow the PC board and component pins to change dimensions evenly, putting minimal stresses on the component. It is recommended to perform reflow soldering no more than twice. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2013 Avago Technologies. All rights reserved. AV02-2867EN - June 4, 2013