ALUMINUMELECTROLYTICCAPACITORS UWX 5.5mmL Chip Type Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Load life of 2000 hours at 85C. UWT Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. High UWJ High Temp reflow Temperature Values marked with an in the dimension table are scheduled to be discontinued and are not recommended for new designs. UWX UWP Bi-polarized Smaller Specifications UZS Item Performance Characteristics Category Temperature Range -40 to +85C Rated Voltage Range 4 to 50V Rated Capacitance Range 1 to 330F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage at 20C, leakage current is not more than 0.01CV or 3 (A) ,whichever is greater. Rated voltage (V) tan (MAX.) Tangent of loss angle (tan ) 6.3 10 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 4 7 15 Rated voltage (V) Z- 25C / Z+20C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Measurement frequency : 120Hz at 20C 16 25 35 50 4 Z- 40C / Z+20C 0.16 (0.19) 6.3 4 8 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Values in ( ) applicable to WR, 3 case size. Measurement frequency : 120Hz 35 25 16 50 2 2 2 2 3 4 4 3 10 3 8 Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 85C. Shelf Life After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Plastic platform 0.3 MAX. 0.3 MAX. 5.4 5.4 +0.1 -0.2 +0.1 -0.2 1 C0.2 C0.2 0.5 to 0.8 2 3 4 5 6 7 8 D A D BA C B E C 3 1.5 3 3.3 1.5 3.3 3.3 0.8 3.3 4 1.8 4 4.3 1.8 4.3 4.3 1.0 4.3 5 2.1 5 5.3 2.1 5.3 5.3 1.3 5.3 11 12 13 14 Taping code Taping code Size code Configuration Capacitance toleranc (20%) Capacitance tolerance (20%) Rated capacitance (10F) RatedRated capacitance voltage(10F) (16V) Negative 0.5 to 0.8 9 10 Configuration A0.2 A0.2 1 Voltage 0.5 MAX. 0.5 MAX. E E A0.2 A0.2 2 Lot No. Within 10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value 2 X 3 1 4 C 5 1 6 0 7 0 8 M 9 C 10 L 11 1 12 G 13 B 14 U1 W UWX 1 C 1 0 0 MC L 1 G B Positive B0.2B0.2 Plastic platform D0.5 D0.5 1 Voltage X2A2 10 10 16V 16V Capacitance 2 Lot No. Capacitance change tan Leakage current Type numbering system (Example : 16V 10F) Positive Capacitance Within 20% of the initial capacitance value (Within 25% for 4 V and 3,WR series units) 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan Leakage Current D Size code Code 3 D 4 to 38 2 Code 12 4 to 8 1 Rated Series voltagename (16V) Negative (mm) 6.3 (mm) 8 2.4 6.3 3.3 8 6.6 2.4 8.3 3.3 6.6 8.3 6.6 8.3 2.2 6.6 2.3 8.3 Series name Type Type * In the case of size 3 in ( ),parentheses, use WX in the 2nd and 3rd 2 digit and put a in the 12th digit of type numbering system. 1. Voltage mark for 6.3V is 6V . E 0.8 1.0 1.3 2.2 2.3 In case of marking for 3 units, "V" for rated voltage is omitted. 1. Voltage mark for 6.3V is 6V . 2. In case of marking for 3 units, Lot No.is expressed by a digit (month code). In case of marking for 3 units, "V" for rated voltage is omitted. 2. In case of marking for 3 units, Lot No.is expressed by a digit (month code). Dimension table in next page. 112 CAT.8100H ALUMINUMELECTROLYTICCAPACITORS UWX Dimensions 4 0G V Cap. (F) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 4 ( 3) 8.4(8.0) 1 010 2.2 2R2 3 8.4 4 ( 3) 13 (10) 3.3 3R3 3 10 4.7 4R7 4 17 4 ( 3) 16 (12) 4 18 5 20 (18) 5 27 (24) 5 29 (24) 6.3 33 (30) 10 100 22 220 3 019 4 ( 3) 28 (21) 5 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8 52 (43) 33 330 4 028 5 37 (34) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8 71 47 470 4 033 5 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80 4 ( 3) 23 (18) 56 560 5 042 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 76 (65) 100 101 5 056 6.3 70 (47) 6.3 76 (54) 6.3 86 8 110 150 151 6.3 079 6.3 220 221 6.3 096 8 110 (74) 330 331 8 145 8 170 71 8 111 (76) 8 135 Case size Rated D (mm) ripple Rated ripple current (mArms) at 85C 120Hz ( ) = 3 units and UWR ( ) is also available with 3mm upon request. ( 3 ) : 3 In such a case, 2 will be put at 12th digit of type numbering system. However, 3 which are scheduled to be discontinued. Not recommended for new designs. Size 4 is available for capacitors marked. " " Size 5 is available for capacitors marked. " " Size 6.3 is available for capacitors marked. " " } In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UUR(p.156), UUG(p.162) if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. 113 CAT.8100H