SPECIFICATION FOR LCD MODULE Model No. TM162ABCW6-2 Prepared by: Date: Checked by : Date: Verified by : Date: Approved by: Date: TIANMA MICROELECTRONICS CO., LTD REVISION RECORD Date Ref. Page Revision No. 1/22 Revision Items Check & Approval 1. General Specifications: 1.1 Display type: STN 1.2 Display color*: Display color: Blue-Black Background: Yellow-Green 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 Backlight: LED 1.7 Controller: S6A0069X01-C0CX (KS0066UP-00CC) 1.8 Display Fonts: 5 x 7 dots + 5 x 1 Cursor (1 Character) 1.9 Data Transfer: 8 Bit Parallel 1.10 Operating Temperature: -20----+70 Storage Temperature: -30----+80 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 16 Characters X 2 Lines 1.13 Dot Size: 0.55X0.50(mm) 1.14 Dot Pitch: 0.60X0.55 (mm) 1.15 Font Size: 2.95X4.35(mm) 1.16 Font Pitch: 3.65X5.05 (mm) 1.17 Weight: 32g * Color tone is slightly changed by temperature and driving voltage. 2/22 3. LCD Module Part Numbering System TM 1 6 2 A B C W6 - 2 OPTIONAL IC INDICATOR (FOR FACTORY USE) MODIFICATION CODE DESIGNATOR WIDE TEMPERATURE RANGE BACKLIGHT TYPE C: TRANSFLECTIVE, LED BACKLIGHT LCD TYPE B: Y-G MODE STN, POSITIVE MODULE SERIES MODULE TYPE 3 DIGITS INDICATING 16 CHARACTERS X 2 LINES T: TIANMA M: MODULE 4/22 , ' -#! 5. Absolute Maximum Ratings Item Symbol Min. Max. Power Supply Voltage VDD VSS -0.3 7.0 Unit Remark V LCD Driving Voltage VLCD -0.3 13.0 Operating Temperature Range TOP -20 +70 Storage Temperature Range TST -30 +80 6/22 No Condensation 6. Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Symbol Min. Typ. Max. Unit Supply Voltage (Logic) VCC VSS 4.5 5.0 5.5 V Supply Voltage (LCD Drive) VLCD - 4.7 - V 0.7VDD - VDD+0.3 V -0.3 - 0.2VDD V IDD VSS =5.0 - 1.5 - mA IEE - 0.40 - mA - - 138.6 mA Input Signal Voltage VIH High VCC=5.0 Low Supply current (Logic) Supply current (LCD Drive) Supply current (LED Drive) VIL VCC=5.0 VCC IDD VLED =4.2 7/22 6.2 Interface Signals Pin No. Symbol Level Description 1 Vss 0V 2 Vcc 5.0V Power supply voltage for logic and LCD(+) 3 Vee 0.3V Power supply voltage for LCD(-) 4 RS H/L Selects registers (H: Data L: Instruction) 5 R/W H/L Selects read or write 6 E H/L Data read/write enable signal 7 DB0 H/L Data bit0 8 DB1 H/L Data bit1 9 DB2 H/L Data bit2 10 DB3 H/L Data bit3 11 DB4 H/L Data bit4 12 DB5 H/L Data bit5 13 DB6 H/L Data bit6 14 DB7 H/L Data bit7 15 A 4.2V Power supply voltage for LED(+) 16 K 0V Power supply voltage for LED(-) Ground 8/22 6.3 Interface Timing Chart AC Characteristics(V=4.5V~5.5V,Ta=-30~+85 0RGH :ULWHy0RGH o5HIHUyWRy)LJco 5HDGy0RGH o5HIHUyWRy)LJaeo &KDUDFWHULVWLF 7 6\PERO 0LQi 7\Si 0D[i WF eii W5nW) ei WZ eei 5i:yDQGy56y6HWXSy7LPH WVXi ei 5i:yDQGy56y+ROGy7LPH W+i ii 'DWDy6HWXSy7LPH WVXe ai 'DWDy+ROGy7LPH W+e ii (y&\FOHy7LPH WF eii W5nW) ei (y3XOVHy:LGWKyo+LJKny/RZo WZ eei 5i:yDQGy56y6HWXSy7LPH WVX ei 5i:yDQGy56y+ROGy7LPH W+ ii 'DWDy2XWSXWy'HOD\y7LPH W' iei 'DWDy+ROGy7LPH W'+ e (y&\FOHy7LPH (y5LVHyiy)DOOy7LPH (y3XOVHy:LGWKyo+LJKny/RZo (y5LVHyiy)DOOy7LPH 8QLW QV QV 56 5i: ( '%ia'%ae 56 5i: ( '%ia'%ae 9 , +i 9 , /i W68i W Ki 9 , /i 9 , +i 9 , /i W 68e WU 9 , +i 9 , /i 9 , /i W Ki WZ WI 9 , +i 9 , /i 9 , /i W Ke 9 , +i 9 , /i 9DOLG 'DWD W& )LJXUHycyiyy:ULWHy0RGHy7LPLQJy'LDJUDP 9 , +i 9 , /i WK W 68 9 , +i 9 , +i WK WZ WU 9 , +i 9 , /i 9 , +i 9 , /i W' 9 , +i 9 , /i 9DOLG 'DWD W& WI 9 , /i W' + 9 , +i 9 , /i )LJXUHyaeyiyy5HDGy0RGHy7LPLQJy'LDJUDP +(>1 ,QVWUXFWLRQy&RGH ([HFXWLRQy ,QVWUXFWLRQ 'HVFULSWLRQ WLPHyoIRVF y 56 5i: '%ae '%c '%e '%e '%e '%e '%i '%i eaeiyN+]o &OHDU y:ULWHy|ei+yWRy''5$0yDQGyVHWy i i i i i i i i i i iieeyPVy 'LVSOD\ y''5$0yDGGUHVVyWRy|ii+yIURPy$& y6HWy''5$0yDGGUHVVyWRy|ii+y yIURPy$&yDQGyUHWXUQyFXUVRUyWRyLWV 5HWXUQy i i i i i i i i i yRULJLQDOySRVLWLRQyLIyVKLIWHGiy iieeyPV +RPH y7KHyFRQWHQWVyRIy''5$0yDUHyQRWy yFKDQJHGi (QWU\y0RGHy y$VVLJQyFXUVRUyPRYLQJyGLUHFWLRQy i i i i i i i i ,i' 6+ eayPV 6HWy yDQGyHQDEOHyWKHyVKLIWyRIyHQWLUHyGLVSOD\iy y6HWyGLVSOD\o'onyFXUVRUo&ony 'LVSOD\y21i eayPV i i i i i i i ' & % yDQGyEOLQNLQJyRIyFXUVRUo%oyRQiRIIy 2))y&RQWURO yFRQWUROyELWi y6HWyFXUVRUyPRYLQJyDQGyGLVSOD\y &XUVRUyRU eayPV i i i i i i 6i& 5i/ yVKLIWyFRQWUROyELWnyDQGyWKHyGLUHFWLRQny y'LVSOD\y 6KLIW yZLWKRXWyFKDQJLQJyRIy''5$0yGDWDiy y6HWyLQWHUIDFHyGDWDyOHQJWKyo'/ay yaELWieELWonyQXPEHUVyRIyGLVSOD\yOLQH eayPV i i i i i '/ 1 ) y )XQFWLRQy6HW yo1ayeOLQHiiOLQHoyDQGnyGLVSOD\ yIRQWyW\SHyo)aeuiiGRWVieuayGRWVo y6HWy&*5$0yDGGUHVVyLQyDGGUHVVy 6HWy&*5$0y i i i i $&e $&e $&e $&e $&i $&i eayPV yFRXQWHUi $GGUHVV 6HWy''5$0y y6HWy''5$0yDGGUHVVyLQyDGGUHVVy eayPV i i i $&c $&e $&e $&e $&e $&i $&i $GGUHVV yFRXQWHUi y:KHWKHUyGXULQJyLQWHUQDOyRSHUDWLRQ 5HDGy%XV\y yRUyQRWyFDQyEHyNQRZQyE\yUHDGLQJy%)iy i i %) $&c $&e $&e $&e $&e $&i $&i iyPV )ODJyDQGy y7KHyFRQWHQWVyRIyDGGUHVVyFRXQWHU $GGUHVV yFDQyDOVRyEHyUHDGi :ULWHy'DWDyWRy y:ULWHyGDWDyLQWRyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV 5$0 yo''5$0i&*5$0oi 5HDGy'DWDy y5HDGyGDWDyIURPyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV IURPy5$0 yo''5$0i&*5$0oi yyyyyyyyyyyyoy||ayGRQ(c)WyFDUH 127(ay:KHQyDQy038ySURJUDPyZLWKyFKHFNLQJyWKHy%XV\y)ODJo'%aeoyLVyPDGHnyLWyPXVWyEHyQHFHVVDU\yiie)RVFyLV yyyyyyyyyyyyyQHFHVVDU\yIRUyH[HFXWLQJyWKHyQH[WyLQVWUXFWLRQyE\yWKHyIDOOLQJyHGJHyRIyWKHyo(oyVLJQDOyDIWHUyWKHy%XV\y)ODJyo'%aeoy yyyyyyyyyyyyyJRHVyWRy|/RZiy yy,QVWUXFWLRQy7DEOH )+0- ;:,6D**))?**7 )+0- ;:,6D**))?**7 7. Optical Characteristics 7.1 Optical Characteristics Item Symbol Ta=25 Condition y =0 x Viewing Angle Response Time Turn on Turn off -35 Typ. -- Max. Cr Unit 20 Cr 2 Deg x =0 y Contrast Ratio Min. x =0 y =0 Ton -30 -- 30 4.0 - - - - 250 x =0 ms y =0 Toff - 13/22 - 250 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Contrast Ratio = B2/B1 = Measuring Conditions: 1) Ambient Temperature: 25 ; unselected state brightness selected state brightness 2) Frame frequency: 64Hz 7.2.3 Definition of Response time Turn on time: t on = t d + t r Turn off time: t off = t d + t f Measuring Condition: 1) LCD Operating Voltage: 4.7V 2) Frame frequency: 64Hz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recautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 18/22 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0 40 Relatively humidity: 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 19/22 Appendix A Inspection items and criteria for appearance defects Items Contents Criteria Leakage Not permitted Rainbow According to the limit specimen Polarizer Wrong polarizer attachment Not permitted Bubble between polarizer and glass Not counted Scratches of polarizer Black spot (in viewing area) <0.3mm Max. 3 defects allowed 0.3mm 0.5mm According to the limit specimen Not counted Max. 3 spots allowed X<0.2mm 0.2mm X 0.5mm X=(a+b)/2 Black line (in viewing area) Not counted Max. 3 lines allowed a<0.02mm 0.02mm a 0.05mm b 2.0mm Progressive cracks Not permitted 20/22 Max. 3 spots (lines) allowed Appendix B Inspection items and criteria for display defects Items Contents Criteria Open segment or open common Not permitted Short Not permitted Wrong viewing angle Not permitted Contrast radio uneven According to the limit specimen Crosstalk According to the limit specimen Not counted Max.3 dots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Black spot (in viewing area) Not counted Max.2 dots allowed A<0.1mm 0.1mm A 0.2mm D<0.25mm Not counted Max.3 spots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Black line (in viewing area) Not counted Max.3 lines allowed a<0.02mm 0.02mm a 0.05mm b 0.5mm 21/22 Max.3 dots allowed Max.3 spots (lines) allowed Appendix B Inspection items and criteria for display defects (continued) Items Content Criteria Not counted Max. 2 defects allowed x 0.1mm 0.1mm x 0.2mm x=(a+b)/2 Not counted Max. 1 defects allowed a 0.1mm 0.1mm a 0.2mm D>0 Transformation of segment Max.2 defects allowed 0.8W a 1.2W a=measured value of width W=nominal value of width 22/22 Max.3 defects allowed