Li ELECTRONICS LTD. DATA SHEET Ref HY0991 BIPOLAR POWER AMPLIFIERS The ILP HY Power Amplifier Modules are a versatile range of building blocks for constructing high quality audio amplifiers with the minimum of additional components. These modular hybrid amplifiers have been designed using Bipolar technolagy to provide high fidelity performance. Encapsulation to an integral heatsink together with internal safeguards to ensure full protection make them extremely rugged, both electrically and mechanically, and therefore suitable for all audio applications. The madules require only five electrical connections, and should be mounted to allow a vertical flow of air through the fins. T slots in the heatsink facilitate mounting using the nuts and screws provided. HY30P | HY60 HY6060 HY124 | H128 | HY244 | HY248 | HY364 | HY368 Output Power Into 4 chms (rms) 60w 120w _ 180w Qutput Power Into 8 chms (rms); 15w 30w 304+30w _ 60w 120w 180w Power Supply Voltage (DC) +18v +25v +25v +25v +35v +35v +45v +42v +55v Loudspeaker Fuse Rating 1.0A {5A 1.5A per Channel 2.5A 2.0A 3.15A 2.54 3.15A 2.5A TYPICAL SPECIFICATION (All amplifiers) Parameter Value INSTALLATION NOTES 1. For normal usage and conditions the amplifier needs Frequency Response (-3dB) 18Hz - 50kHz no supplementary heatsink; it must be mounted to allow Total Harmonic Distortion @ 1kHz < 0.015% a vertical flow of air through the fins. / modules up to 30 watts 2. The amplifier must be powered from a true splitline Total Harmonic Distortion @ 1kHz < 0.01% (symmetrical) supply and under no circumstances should modules 60 watts and above any attempt be made to use a single line. ; . . 3. No input capacitor is required. An internal 100V Signal to Noise Ratio (DIN AUDIO) 100dB working capacitor is fitted. 4. For loudspeaker protection it is recommended that a Slew Rate 16V/US. quickblaw fuse is mounted between the output and the Rise Time buS speaker. The fuse ratings in the table have been u calculated to ensure fast rupture in the event of DC being i, presented to the speaker. It is advised not to use higher input Sensitivity 500mV rms rated fuses. 5. Star earthing techniques should be employed to Input Impedance 100Kohms prevent hum loops. i.e. all 0 volt connections, including Load Impedance HY124/244/364 4- co ohms speaker return leads should be made at the power supply. P Allothers 8 = o0 ohms 6. Connecting leads between power supply smoothing Damping Factor (ohms @100 Hz) 5 400 capacitors and the module should be less than 300mm L long. Longer leads may cause instability and module failure.MECHANICAL DETAILS CONNECTION DETAILS HY6060 e] e2 e5 ef @4 03 e7 08 e039 e 10 PIN 1. Output \ 2. Input 3. Negative supply 4. O volt 5. Positive supply _/ 6. Negative supply 7. Ovolt 8. Positive supply 9. Input [ 10.Output / APPLICATION CIRCUIT AND DIMENSIONS (not to scale) f18m = HY30P, 60, 12X, 24X, 36X ) ia ie 05 <O wl a @) @ eo? 3 ef ; - a he B t c a r BASE OUTLINE, SIDE OUTLINE SIDE OUTLINE e| ALL HY SERIES HY6G, 124/8, 244/8 364/8,6060 HY30P ONLY HY30P | HY60 |HY6060 |HY124/8| HY244/8| HY364/8 PIN 1. Positive Supply A go | 76 | 120 | 120 | 120 | 120 2. Output 3. Input B 40 40 40 40 50 100 4. Ovolt C 2 | 68 | 78 | 78 | 78 | 78 5. Negative supply D 68 66 107 107 107 107 Panel 1 N/A. | 57x41 | 97x41 | 97x51 | 97x51 | S7x101 Weight] 145g | 240g | 420g | 410g | 520g | 1030g All dimensions are nominal and in mm, unless stated. FIXING The T slots in the heatsink extrusion allow easy mounting. Nuts and balts are supplied. HY60 Size M3; All others Size M4 POWER SUPPLY REQUIREMENTS ILP manufacture a range of power supply units for the HY series of amplifiers. They consist of a printed circuit board containing the rectifiers and smoothing components and a high quality toroidal transformer. All modules & % HY 6060 +VE Power Supply -ve | ct N Base View Left Channel Right Channel | stor L --E * In order to prevent earthlaop problems when a pre-amplitier is connected we racommend the fitting of a resistor should be between 82 and 2700, 1) in the postion shown. The value of R1 watt power rating. For x in transformer part number use: 3 for 120 or 240 volt operation 1 for 220 volt operation Call Sales Office for other supply voltages. HY30P HY60 HY6060 HY124 HY128 HY244 HY248 HY364 HY368 DC Board for 1 amplifer DC21 DC41 DC41 DC41 DC42 DC51 DC54 DC73 DC74 DC Board for 2 amplifiers DC21 DC41 _ DC52 DC51 DC71 DC72 Dc73 acra Transformer for 1 amplifer 2x013 4x027 4x027 4x027 4x016 5x016 5x018 7x018 7x026 Transformer for 2 amplifiers} 2x013 4x027 5x015 5x016 7x016 7x018 74018 73028 * Note: DC Board includes rectifiers and smoothing capacitors, mounted ona circuit board. Example: | Complete Power Supply Unit for operating 2 x HY124 on 240V a.c. is: 1x DC52 and 1 x 53015. For full details of Power Supply Units including connection and installation see ILPs Power Supply Data Sheet. ait TEL LS Fa wl |_| | 7 PAxY CsZ as Fan STS ELECTRONICS LTD. COTTON ROAD -: WINCHEAP CANTERBURY -: KENT CT1 3RB Telephone: (QGG73-3564776 Facsimile: @EE7} 450507: DISTRIBUTED BY:- Every effort has been made to ensure the accuracy of the details in this data sheet. However, in the interests of product improvement, !LP reserve the right to change any part of this specification without notice. ILP cannot be held responsible for any damage to other equipment that may occur during the use of these modules