DATA SHEET TFT COLOR LCD MODULE NL8060BC26-17 26 cm (10.4 inches), 800 x 600 pixels, 262,144 colors high luminance, wide viewing angle DESCRIPTION The NL8060BC26-17 is a TFT (thin film transistor) active-matrix color liquid crystal display (LCD) module comprising an amorphous silicon TFT attached to each signal electrode, a driving circuit, and a backlight. The NL8060BC26-17 has a built-in backlight. The backlight includes long-life lamps, which are replaceable, and a holder. The 26 cm diagonal display area contains 800 x 600 pixels and can display 262,144 colors simultaneously. The NL8060BC26-17 is suitable for industrial application use because the viewing angle is wide and the luminance is high. The viewing direction is selectable for either the upper or the lower side by changing the scan direction. FEATURES * High luminance (280 cd/m2, typ.) * Wide viewing angle (with retardation film) * Low reflection * Reversible scan direction * 6-bit digital RGB signals * Data enable (DE) function * Edge-type backlight with two long-filetime lamps (one lamp holder) * Replaceable lamp holder * Recommendation inverter for a backlight: Part No. 104PWBR1 APPLICATIONS * Display terminals for control systems * Monitors for process controllers The information in this document is subject to change without notice. Please confirm the delivery specification before starting to design your system. Document No. EN0493EJ1V1DS00 (1st edition) Date Published January 2001 P CP(N) Printed in Japan 2000 NL8060BC26-17 STRUCTURE AND FUNCTION A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure, LSIs for driving the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are connected to the panel, the backlight assembly is attached to the back side of the panel. RGB (red, green, blue) data signals from a source system are modulated into a form suitable for active-matrix addressing by the onboard signal processor and sent to the driver LSIs, which in turn address the individual TFT cells. Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when activated by the data source. By regulating the amount of light passing through the array of red, green, and blue dots, color images are created with clarity. CHARACTERISTICS (at room temperature) Display area Drive system Display colors Number of pixels Pixel arrangement Pixel pitch Module size Weight Contrast ratio Viewing angle (more than the Designed viewing direction Color gamut Response time Luminance Signal system Supply voltage Backlight Power consumption 2 211.2 (H) x 158.4 (V) mm a-Si TFT active matrix 262,144 colors 800 x 600 pixels RGB vertical stripe 0.264 (H) x 0.264 (V) mm 243.0 (H) x 185.1 (V) x 11.5 max. (D) mm 520 (typ.) 300:1 (typ.) contrast ratio of 10:1) Horizontal: 50 (typ. left side, right side) Vertical: 35 (typ. up side), 45 (typ. down side) * Wider viewing angle with contrast ratio: down side (6 o'clock, normal scan) up side (12 o'clock, reverse scan) * Wider viewing angle without image reversal: up side (12 o'clock, normal scan) down side (6 o'clock, reverse scan) * Optimum gray-scale ( = 2.2): perpendicular 43% (typ. center, to NTSC) 15 ms (max.), "white 100%" to "black 10%" 280 cd/m 2 (typ.) (lamp current: I L = 5 mA rms per lamp) 6-bit digital signals for each of the RGB primary colors, synchronous signals (Hsync, Vsync), dot clock (CLK) 3.3 V [5.0 V] (logic, LCD driving) Edge light type, two cold cathode fluorescent lamps in a holder, attached inverter * Lamp holder set: Part no.104LHS31 * Recommended inverter: Part no. 104PWBR1 7.0 W (typ. at 3.3 V, with recommended inverter) Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 BLOCK DIAGRAM 47 H-driver R0 ~ R5 47 * * * * * * Digital signal processor G0 ~ G5 47 Level shift 2400 lines B0 ~ B5 V-driver 47 CLK 47 Hsync 47 * * * * * TFT LCD panel 600 lines H: 800 x 3 (R, G, B) V: 600 LCD timing controller Vsync 47 DE 47 MODE DPS 47 k VCC VHIGH VLOW Power supply circuit LSIs Drivers Backlight GND (SG) Frame Note: Frame is not connected with GND (SG). If connecting the NEC-recommended inverter VDDB Inverter Backlight BRTHL BRTC (Part no. 104PWBR1) BRTH BRTL GNDB Data Sheet EN0493EJ1V1DS00 3 NL8060BC26-17 GENERAL SPECIFICATIONS Item Specification Unit Module size 243.0 0.5 (H) x 185.1 0.5 (V) x 11.5 max. (D) mm Display area 211.2 (H) x 158.4 (V) mm 800 (H) x 600 (V) pixel Dot pitch 0.088 (H) x 0.264 (V) mm Pixel pitch 0.264 (H) x 0.264 (V) mm Number of pixels Pixel arrangement RGB (red, green, blue) vertical stripe Display colors Weight 262,144 color 520 (typ.) 550 (max.) g ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit VCC -0.3 to 6.5 V VI - VCC < 3.0 Input voltage VI -0.3 to 6.5 V Ta = 25 C Lamp voltage VL 2000 Vrms Ta = 25 C Storage temp. TST -20 to 60 C Operating temp. TOP 0 to 50 C Module surfaceNote < = 95 % Ta < = 40 C < = 85 % 40 < Ta <= 50 C Absolute humidity shall not exceed Ta = 50 C, RH = 85 % g/m3 Supply voltage Relative humidity (RH) Absolute humidity Remarks Ta > 50 C Note: Measured at the panel surface (including self-heat) ELECTRICAL CHARACTERISTICS (1) Logic, LCD Driving Ta = 25 C Parameter Symbol Min. Typ. Max. Unit Supply voltage VCC 3.0 (4.75) 3.3 (5.0) 3.6 (5.25) V VCC = 3.3 V (VCC = 5.0 V) Logic input "L" voltage VIL 0 - VCC x 0.3 V CMOS level Logic input "H" voltage VIH VCC x 0.7 - VCC V Supply current ICC - - 360 (270)Note 550 (500) mA Note: Checker flag pattern (in EIAJ ED-2522) 4 Data Sheet EN0493EJ1V1DS00 Remarks VCC = 3.3 V (VCC = 5.0 V) NL8060BC26-17 (2) Backlight Ta = 25 C Parameter Symbol Min. Typ. Max. Unit Remarks Lamp current IL 2.0 5.0 5.5 mA rms with one lamp Lamp voltage VL - 510 - V rms - Lamp turn-on voltage VS 840 - - V rms 1265 - - 50 54 58 Oscillator frequency Ft Ta = 25 C *2 Ta = 0 C *2 kHz *1 Notes: 1. Recommended value of Ft. * Ft is within the specification. and * Ft = 1/4Th x (2n -1) Th: Hsync period n: a natural number (1, 2, 3...) If Ft is out of the recommended value, interference between the Ft frequency and Hsync frequency may cause a beat on the display. 2. When Vs is less than the minimum value, the lamp might be not turned on. 3. Recommended inverter: Part no. 104PWBR1 SUPPLY VOLTAGE SEQUENCE Notes: 1. The supply voltage for input signals should be the same as VCC. 2. Turn on the backlight within the LCD 3.0 (4.75 V) 0 s<t<35 ms 0 s<t<35 ms 3.0 (4.75 V) operation period. When the backlight turns on before LCD operation or the VCC LCD operation turns off before the VALID priod. backlight turns off, the display may Signals VCC - ON Time VCC - OFF Signals: CLK, Hsync, Vsync, DE, R0 ~ R5, G0 ~ G5, B0 ~ B5 momentarily become white. 3. When the power is off, please keep whole signals (Hsync, Vsync, CLK, DE, R0 ~ R5, G0 ~ G5, B0 ~ B5) at low level or high impedance. 4. The wrong power sequence may damage the module. 5. The signal should not be down during operation. Even if the signal could recover, the LCD module cannot be operated correctly and the display may be non-uniform. If the signal is down, VCC should be turned off, and then VCC and the signal should be turned on as in the sequence above. Data Sheet EN0493EJ1V1DS00 5 NL8060BC26-17 INTERFACE AND CONNECTOR PIN ASSIGNMENT (1) Interface Signals, Power Supply Module side connector Mating connector CN1 DF9-41P-1V (No. 1 to 41) DF9-41S-1V Supplier: Hirose Electric Co., Ltd. Pin No. Symbol Pin No. Symbol 1 GND Ground Function 22 GND Ground 2 CLK Dot clock 23 G3 Green data 3 GND Ground 24 G4 Green data 4 Hsync Horizontal sync. 25 G5 Green data (MSB) 5 Vsync Vertical sync. 26 GND Ground 6 GND Ground 27 GND Ground 7 GND Ground 28 GND Ground 8 GND Ground 29 B0 Blue data (LSB) Function 9 R0 Red data (LSB) 30 B1 Blue data 10 R1 Red data 31 B2 Blue data 11 R2 Red data 32 GND Ground 12 GND Ground 33 B3 Blue data 13 R3 Red data 34 B4 Blue data 14 R4 Red data 35 B5 Blue data (MSB) 15 R5 Red data (MSB) 36 GND Ground 16 GND Ground 37 DE Data enable signal 17 GND Ground 38 DPS Scan direction select Note 3 18 GND Ground 39 VCC Power supply Note 1 19 G0 Green data (LSB) 40 VCC Power supply Note 1 20 G1 Green data 41 MODE Mode select Note 2 21 G2 Green data LSB: Least-Significant Bit MSB: Most-Significant Bit Notes: 1. VCC: All VCC terminals should be connected to 3.3 V [5.0 V]. 2. MODE: H = Fixed mode L or open = DE mode 3. DPS can change scan direction (normal scan and reverse scan). DPS: Vcc = normal scan GND or open = reverse scan See page 16, DISPLAY POSITION, for an altemate reversible scan. 6 Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 (2) Lamp Connector Lamp side connector Mating connector CN2 *** BHR-03VS-1 SM02 (4.0) B-BHS-TB Supplier: J.S.T. Trading Company, Ltd. Pin No. Symbol Function 1 VLOW Low voltage terminal 2 VHIGH High voltage terminal 3 VHIGH High voltage terminal Caution: VHIGH and VLOW must be connected correctly. If they are connected incorrectly, the user may get hurt and the module may break. a) Connection of recommended inverter: 104PWBR1 (NEC) Inverter side connector 1 Mating connector 1 CN1 *** LZ-5P-SL-SMT LZ-5S-SC3 Supplier: Japan Aviation Electronics Industry, Limited (JAE) Pin No. Symbol 1 VDDB 2 VDDB 3 GNDB Function Pin No. Symbol Function Power supply (12 V) 4 GNDB Backlight ground Power supply (12 V) 5 BRTHL Luminance selectNote Backlight ground Note: High luminance (100%): BRTHL = High (+5 V) or open Low luminance (60%): BRTHL = Low (GNDB level) Inverter side connector 2 Mating connector 2 CN3 *** IL-Z-3PL-SMTY IL-Z-3S-S125C3 Supplier: Japan Aviation Electronics Industry, Limited (JAE) Pin No. Symbol Function 1 BRTC Backlight On/Off signal Note 1 2 BRTH Luminance control input Note 2 3 BRTL Luminance control input Note 2 Notes: 1. TTL level Backlight On: BRTC = High (+5 V) or open Backlight Off: BRTC = Low (GNDB level) Data Sheet EN0493EJ1V1DS00 7 NL8060BC26-17 2. <1> Luminance control by a variable resistor This way works when BRTHL (the no. 5 pin) of CN3 is opened. BRTH BRTL 10 K 5 % Minimum luminance (50%): R=0 Maximum luminance (100%): R = 10 K R <2> Mating variable resistor: Luminance control by voltage This way works when BRTL is opened. The range of input voltage between BRTH and GNDB is as follows. Minimum luminance (50%): 2.5 V Maximum luminance (100%): <= 1.2 V 8 Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 (3) Connector Location Upper side CN2 <Rear view> 1 2 3 4 * * CN1 * * Lower side * * * * CN3 Recommended inverter (104PWBR1) * * 41 40 <Module side pin arrangement of CN1> 1 1 1 2 2 2 3 3 3 4 <Lamp side pin arrangement of CN2> <Inverter side pin arrangement of CN3> 5 <Inverter side pin arrangement of CN1> Data Sheet EN0493EJ1V1DS00 9 NL8060BC26-17 DISPLAY COLORS vs. INPUT DATA SIGNALS Display Colors Data Signal (0: Low level; 1: High level) R5 R4 R3 R2 R1 R0 Basic colors Red gray-scale Green gray-scale B5 B4 B3 B2 B1 B0 Black Blue Red Magenta Green Cyan Yellow White 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Dark Bright | | | | | | | | | 1 1 1 1 1 1 1 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Dark Bright Green Black Blue gray-scale G5 G4 G3 G2 G1 G0 Dark Bright Blue | | | | | | | | | 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 1 1 0 1 1 1 0 1 | | | 0 0 0 0 0 0 0 0 0 | | | 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 | | | 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 Note: Colors are developed in combination with 6-bit signals (64 steps in gray-scale) of each primary red, green, and blue color. This process can result in up to 262,144 (64 x 64 x 64) colors. 10 Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 INPUT SIGNAL TIMING (1) Input Signal Specifications Parameter CLK Symbol Min. Typ. Max. Unit 1/tC 34.0 38.362 40.0 MHz tch/tC 0.4 0.5 0.6 - - Rise, fall tcrf - - 10 ns - Period th 24.3 26.693 - s 37.468 kHz (typ.) - 1024 - CLK Frequency Duty Hsync Display period thd Front porch thf Pulse width Back porch 800 thp thb - 24 - CLK Fixed mode 4 24 - CLK DE mode 2 72 127 CLK Fixed mode 2 72 - CLK DE mode 2 128 198 CLK Fixed mode 2 128 - CLK DE mode CLK Fixed mode DE mode 200 15 200 - CLK thch 10 - - ns - Hsync-CLK timing thcs 8 - - ns - Hsync-Vsync timing thv 1 - - CLK - Vsync-Hsync timing tvs 15 - - ns - Rise, fall thrf - - 10 ns - tv 16.1 16.683 17.2 ms - 625 - H Period Display period tvd Front porch tvf Back porch 600 tvp tvb 59.94 Hz (typ.) H - 1 - H Fixed mode - 1 - H DE mode 1 2 23 H Fixed mode 1 2 - H DE mode 1 22 23 H Fixed mode 1 22 - H DE mode H Fixed mode DE mode tvp + tvb DE CLK CLK-Hsync timing Pulse width DATA R0 ~ R5 G0 ~ G5 B0 ~ B5 26.067 ns (typ.) - thp + thb Vsync Remarks 24 2 24 254 H Rise, fall tvrf - - 10 ns - CLK-DATA timing tds 8 - - ns - DATA-CLK timing tdh 12 - - ns - Rise, fall tdrf - - 10 ns - DE-CLK timing tes 8 - - ns - CLK-DE timing teh 12 - - ns Rise, fall terf - - 10 ns Note: All parameters should be kept in the specified range. Data Sheet EN0493EJ1V1DS00 11 NL8060BC26-17 (2) Input Signal Timing <Vertical> tv tvp Vsync tvf tvb Display period (Note) tvd DE <Horizontal> th thp Hsync thf thb Display period (Note) thd DE Note: 12 These do not exist as signals. Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 (3) Input Signal Timing Chart tC tch CLK 0.7 VCC 0.5 VCC 0.3 VCC tcrf tcrf tds DATA tdh Invalid Invalid (R0 ~ R5) 0.7 VCC (G0 ~ G5) 0.5 VCC (B0 ~ B5) 0.3 VCC tdrf teh DE tdrf tes terf 0.5 VCC thch Hsync tes 0.7 VCC 0.5 VCC 0.3 VCC terf CLK teh thcs 0.7 VCC 0.5 VCC 0.3 VCC thrf Hsync 0.5 VCC thv Vsync ths 0.7 VCC 0.5 VCC 0.3 VCC tvrf Data Sheet EN0493EJ1V1DS00 13 NL8060BC26-17 a) Fixed timing mode Vsync 1 H (min.) 1 H (min.) 1H 24 H (fixed) 600 H (fixed) 1H Hsync 23 1 2 3 623 0 624 24 Hsync 25 24 623 624 0 R0 ~ R5 G0 ~ G5 B0 ~ B5 D (X, 0) D (X, Y) D (X, 598) D (X, 599) Invalid Invalid (Note: X = 0 to 799) Hsync R0 ~ R5 G0 ~ G5 B0 ~ B5 D (X, Y) D (0, Y) D (1, Y) Invalid D (798, Y) D (799, Y) Invalid Hsync 2 CLK (min.) 1 CLK 2 CLK (min.) 200 CLK (fixed) 800 CLK (fixed) 24 CLK CLK 1 2 200 201 1000 1001 1023 R0 ~ R5 G0 ~ G5 B0 ~ B5 Invalid D (0, Y) D (1, Y) D (799, Y) Invalid (Note: Y = 0 to 599) 14 Data Sheet EN0493EJ1V1DS00 0 NL8060BC26-17 b) DE mode Vsync 1H tvp tvb tvf 600 H (fixed) Hsync 0 1 0 1 2 DE R0 ~ R5 G0 ~ G5 B0 ~ B5 D (X, 0) D (X, Y) D (X, 599) Invalid Invalid (Note: X = 0 to 799) DE R0 ~ R5 G0 ~ G5 B0 ~ B5 D (0, Y) D (1, Y) Invalid D (X, Y) D (798, Y) D (799, Y) Invalid Hsync 1 CLK thp thb 800 CLK (fixed) thf CLK 0 1 2 0 1 DE R0 ~ R5 G0 ~ G5 B0 ~ B5 Invalid D (0, Y) D (1, Y) D (799, Y) Invalid (Note: Y = 0 to 599) Data Sheet EN0493EJ1V1DS00 15 NL8060BC26-17 DISPLAY POSITION D (799, 1) D (0, 1) D (1, 1) --------- D (X, 1) --------- D (798, 1) D (799, 1) --- --------- D (X, Y) ----------------- --- --- --------- D (798, Y) D (799, Y) --- --------- --- D (1, Y) --- D (0, Y) --- --------- --- D (798, 1) --- --------- --- D (X, 1) --- --------- --- D (1, 1) --- D (0, 1) --- Normal scan (DPS = "Vcc") D (0, 598) D (1, 598) --------- D (X, 598) --------- D (798, 598) D (799, 598) D (0, 599) D (1, 599) --------- D (X, 599) --------- D (798, 599) D (799, 599) Reverse scan (DPS = "GND" or "Open") D (0,599) D (799,598) D (798,598) --------- D (X, 598) --------- D (1,598) D (0,598) --------- D (1, Y) --------- --- --------- D (0, Y) --- D (X, Y) --- --- --------- --- --------- --- --D (798, Y) --- D (799, Y) --------- --- D (1,599) --- --------- --- D (X, 599) --- --------- --- D (798,599) --- D (799,599) D (799, 1) D (798, 1) --------- D (X, 1) --------- D (1, 1) D (0, 1) D (799, 0) D (798, 0) --------- D (X, 0) --------- D (1, 0) D (0, 0) The drawings below show the relationship between the scan direction and the viewing direction. Normal scan D (0, 0) C N 1 D (0, 599) Reverse scan C N 2 D (799, 0) D (0, 0) D (799, 0) D (0, 599) D (799, 599) D (799, 599) C N 2 16 Data Sheet EN0493EJ1V1DS00 C N 1 NL8060BC26-17 OPTICAL CHARACTERISTICS Ta = 25C Note 1 Item Contrast ratio Symbol Condition CR Luminance Note 2 Lu max Luminance uniformity Note 2 - Min. Typ. Max. Unit Remarks 150 300 - - Note 3 Note 4 200 280 - cd/m2 - - 1.4 - Note 5 Min. Typ. Max. Unit Remarks Note 6 max./min. Reference data Item Response time Color gamut Viewing Horizontal angle range Vertical Symbol Condition ton White to black 100% 10% - 15 50 ms toff Black to white 0% 90% - 65 80 ms C at center, to NTSC - 43 - % - x+ CR > 10, y = 0 45 50 - deg. Note 7 x- CR > 10, y = 0 45 50 - deg. y+ CR > 10, y = 0 30 35 - deg. y- CR > 10, y = 0 40 45 - deg. Notes: 1. VCC = 3.3 V; IL = 5.0 mA rms; DPS = High at normal scan with recommended inverter. 2. Viewing angle: x = 0, y = 0, at center. 3. The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = Luminance with all pixels in "white" Luminance with all pixels in "black" The luminance is measured in darkroom. 4. The luminance is measured after 20 minutes from the module works, with all pixels in "white". Typical value is measured after luminance saturation. The luminance is measured in darkroom. 1 Photodetector (TOPCON BM-5A) 50 cm LCD Module Data Sheet EN0493EJ1V1DS00 17 NL8060BC26-17 5. The luminance uniformity is calculated by using following formula. Luminance uniformity = Maximum luminance Minimum luminance The luminance is measured at or near the five points shown below. Column (160) (320) (480) Line 1 4 (120) 3 (240) 2 5 (360) 6. Definition of response time is as follows. The photodetector output signal is measured when the luminance changes from white to black or from black to white. 100% Display color White Luminance range 90% Black 10% 0% ton toff Time 7. Definitions of viewing angles are as follows. Perpendicular 12 o'clock x- Left y+ Upper x+ y- Lower Right 18 Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 RELIABILITY TEST Test Items Test Conditions High temperature/humidity 50 2C, 85% relative humidity operation 240 hours Notes Note 1 Display data is black. Heat cycle (operation) <1> 0C 3C ... 1 hour Note 1 55C 3C ... 1 hour <2> 50 cycles, 4 hours/cycle <3> Display data is black. Thermal shock (nonoperation) <1> -20C 3C ... 30 minutes Note 1 60C 3C ... 30 minutes <2> 100 cycles <3> Temperature transition time within 5 minutes Vibration (nonoperation) <1> 5 - 100 Hz, 19.6 m/s2 (2G) 1 minute/cycle, Note 1 Note 2 X, Y, Z direction <2> 120 times each direction Mechanical shock (nonoperation) <1> 539 m/s2 (55G), 11 ms Note 1 X, Y, Z direction Note 2 <2> 5 times each direction ESD (operation) 150 pF, 150 , 10 kV Note 1 9 places on a panel Note 3 10 times each place at one-second intervals Dust (operation) 15 kinds of dust (JIS Z 8901) Note 1 Hourly 15 seconds stir, 8 times repeat Notes: 1. Display function is checked by the same condition as the LCD module outgoing inspection. 2. Physical damage. 3. Discharge points are shown as follows. Data Sheet EN0493EJ1V1DS00 19 NL8060BC26-17 GENERAL CAUTIONS The figures and statements below are very important. Please be sure you understand their contents completely. CAUTION This mark indicates that you will get hurt and/or the module will be damaged if you make a mistake in operation. This figure indicates that you will get hurt if you make a mistake in operation. CAUTION (1) Caution when taking out the module <1> Pick up the pouch only, when removing the module from a carrier box. (2) Cautions for handling the module <1> As electrostatic discharges may break the LCD module, handle the LCD module with care against electrostatic discharges. <2> As the LCD panel and backlight element are made from fragile glass material, impact and pressure to the LCD module should be avoided. <3> As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. <4> Do not pull the interface connectors in or out while the LCD module is operating. <5> Put the module display side down on a flat horizontal plane. <6> Handle connectors and cables with care. <7> When the module is operating, do not lose the CLK, Hsync, or Vsync signal. If any one of these signals is lost, the LCD panel will be damaged. <8> <9> The torque for mounting screws should never exceed 0.294 N*m (3 kgf*cm). Don't push or rub the surface of the LCD module. If you do, scratches or rubbing marks may be left on the surface of the module. <10> Do not give any stress to the interface connector. (3) Cautions regarding atmosphere <1> <2> Dew-drop atmosphere must be avoided. Do not store and/or operate the LCD module in a high-temperature and/or high-humidity atmosphere. Storage in an electro-conductive polymer packing pouch and in a relatively low-temperature atmosphere is recommended. <3> This module uses cold cathode fluorescent lamps. Therefore, the lifetime of the lamp is shortened conspicuously at very low temperatures. <4> Do not operate the LCD module in a high magnetic field. (4) Cautions about module characteristics <1> Do not apply any fixed-pattern data signals to the LCD module at product aging. Applying a fixed pattern for a long time may cause image sticking. <2> This module has retardation film, which may cause variation of the color hue at different viewing angles. Nonuniformity may appear on the screen during high-temperature operation. <3> A light vertical stripe may be observed, depending on the display pattern. This is not a defect or a malfunction. <4> Noise from the inverter circuit may be observed in the luminance control mode. This is not a defect or a malfunction. 20 Data Sheet EN0493EJ1V1DS00 NL8060BC26-17 (5) Other cautions <1> Do not disassemble and/or reassemble the LCD module. <2> Do not readjust variable resistors or switches, etc. <3> When returning the module for repair, etc., please pack the module properly so as to avoid damages. We recommend using the original shipping packages. <4> If a scan converter is used to convert the VGA signal to NTSC, it is recommended to use the frame memory type, not the line memory. The liquid crystal display has the following specific characteristics. These are not defects or malfunctions. The display condition of the LCD module may be affected by the ambient temperature. The LCD module uses a cold cathode tube for backlighting. Optical characteristics, like luminance or uniformity, will change over time. Uneven brightness and/or small spots may be observed, depending on different display patterns. Data Sheet EN0493EJ1V1DS00 21 11.5 MAX 22 OUTLINE DRAWING FRONT SIDE (Unit: mm) 243 0.5 235 0.3 (4.8) (215.4) (BEZEL OPENING) 7.2 0.3 11.5 MAX. 5.25 0.3 (4) (2.9) (12.9) (2.8) 11.5 MAX. (9.3) (5.7) 2.75 0.2 (211.2) (ACTIVE AREA) (3.9) (8.1) (5.1) (29.4) (6.3) 5.25 0.3 (88.3) 132.6 0.3 (3.15) 166.6 0.3 185.1 0.5 (ACTIVE AREA) (158.4) (ACTIVE AREA) (MODULE CENTER) 2.75 0.2 (161.8) (BEZEL OPENING) (1.8) (88.3) Data Sheet EN0493EJ1V1DS00 146.6 0.3 (4.7) 17 0.3 2-R1.75 5.25 0.3 (3.7) CN1 DF9C-41P-1 V (4.7) 4-CPIMS x M2 x L4 2- 3.5 2.75 0.2 (5.1) (8.1) Notes : (2.8) (4) 1. The torque on mounting screws should never exceed 0.294 N*m (3Kgf*cm). 2. The values in parentheses are for reference. (2.9) (3.9) NL8060BC26-17 8.25 TYP. 8.25 TYP. 8.25 TYP. 5.25 0.3 (5.7) 2.75 0.2 OUTLINE DRAWING REAR SIDE (Unit: mm) BHR-03VS-1 (JST) 1 PIN: COLD: 2, 3 PINS: HOT (3.4) (4.5) 60 10 (2.4) (5) (5) (5.6) (5.3) NION VOLTEGE CAUTION RISK OF ELECTRIC SHOCK. DISCONNECT THE ELECTRIC POWER BEFORE SERVICE. (8) (5) (6.8) 88.9 0.5 4.0 0.5 Name 104DLM- - (16) Pal No. (5) (5) S THE TFT COLOR LCD PANEL CONTAINS COLD CATHODE FLUORESCENT LAMPS. PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR THEIR DISPOSAL. (22) Data Sheet EN0493EJ1V1DS00 2.3 0.5 (5) DF9C-41P-1 V (5) (5) (3.4) (4.5) MADE IN JAPAN (6.6) (2.4) (5.3) 23 (3.4) ES2228423 K2000A483324 NL8060BC26-17 (6.8) NL8060BC26-17 K2 0 0 0 A 4 8 3 3 2 4 NL8060BC26-17 No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its e l e c t r o n i c components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, firecontainment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard," "Special," and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific a p p l i c a t i o n . T h e r e c o m m e n d e d applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical e q u i p m e n t ( n o t specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majorityowned subsidiaries. (2) "NEC electronic component products" means any electronic component product developed or manufactured by or for NEC (as defined above). DE0202