CY7B991V 3.3 V RoboClock(R) Low Voltage Programmable Skew Clock Buffer 3.3 V RoboClock(R) Low Voltage Programmable Skew Clock Buffer Features Functional Description All output pair skew <100 ps typical (250 ps max) 3.75 MHz to 80 MHz output operation User-selectable output functions: Selectable skew up to 18 ns Inverted and non-inverted Operation at one-half and one-quarter input frequency Operation at 2 x and 4 x input frequency (input as low as 3.75 MHz) The CY7B991V 3.3 V RoboClock(R) low-voltage programmable skew clock buffer (LVPSCB) offers user-selectable control over system clock functions. These multiple output clock drivers provide the system integrator with functions necessary to optimize the timing of high-performance computer systems. Each of the eight individual drivers - arranged in four pairs of user controllable outputs - can drive terminated transmission lines with impedances as low as 50 . This delivers minimal output skews and full-swing logic levels (LVTTL). Zero input to output delay 50% duty cycle outputs Low-voltage transistor-transistor logic (LVTTL) outputs drive 50 terminated lines Operates from a single 3.3 V supply Low operating current 32-pin plastic leaded chip carrier (PLCC) package Low cycle-to-cycle jitter (100 ps typical) Each output is hardwired to one of nine delay or function configurations. Delay increments of 0.7 to 1.5 ns are determined by the operating frequency, with outputs able to skew up to 6 time units from their nominal `zero' skew position. The completely-integrated phase-locked loop (PLL) allows external load and transmission line delay effects to be canceled. When this `zero delay' capability of the LVPSCB is combined with the selectable output skew functions, the user can create output-to-output delays of up to 12 time units. Divide-by-two and divide-by-four output functions are provided for additional flexibility in designing complex clock systems. When combined with the internal PLL, these divide functions enable distribution of a low frequency clock that is multiplied by two or four at the clock destination. This feature minimizes clock distribution difficulty, allowing maximum system clock speed and flexibility. For a complete list of related resources, click here. Logic Block Diagram TEST PHASE FREQ DET FB REF FILTER VCO AND TIME UNIT GENERATOR FS 4F0 4F1 3F0 3F1 4Q0 SELECT INPUTS (THREE LEVEL) 4Q1 SKEW 3Q0 3Q1 SELECT 2F0 2F1 2Q0 MATRIX 2Q1 1Q0 1F0 1F1 1Q1 Cypress Semiconductor Corporation Document Number: 38-07141 Rev. *L * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised November 2, 2016 CY7B991V Contents Pinouts .............................................................................. 3 Pin Definitions .................................................................. 3 Block Diagram Description .............................................. 4 Phase Frequency Detector and Filter .......................... 4 VCO and Time Unit Generator .................................... 4 Skew Select Matrix ...................................................... 4 Test Mode .......................................................................... 5 Operational Mode Descriptions ...................................... 6 Maximum Ratings ............................................................. 9 Operating Range ............................................................... 9 Electrical Characteristics ................................................. 9 Capacitance .................................................................... 10 Thermal Resistance ........................................................ 10 AC Test Loads and Waveforms ..................................... 10 Switching Characteristics (-2 option) ........................... 11 Switching Characteristics (-5 Option) .......................... 12 Document Number: 38-07141 Rev. *L Switching Characteristics (-7 Option) .......................... 13 AC Timing Diagrams ...................................................... 14 Ordering Information ...................................................... 15 Package Diagram ............................................................ 16 Acronyms ........................................................................ 17 Document Conventions ................................................. 17 Units of Measure ....................................................... 17 Document History Page ................................................. 18 Sales, Solutions, and Legal Information ...................... 20 Worldwide Sales and Design Support ....................... 20 Products .................................................................... 20 PSoC(R)Solutions ....................................................... 20 Cypress Developer Community ................................. 20 Technical Support ..................................................... 20 Page 2 of 20 CY7B991V Pinouts FS VCCQ REF GND 4 3 2 1 32 31 30 29 2F1 3F0 TEST Figure 1. 32-pin PLCC pinout 2F0 7 27 1F1 VCCQ 8 26 1F0 VCCN 9 25 VCCN 4Q1 10 24 1Q0 4Q0 11 23 1Q1 GND 12 22 GND GND 13 21 14 15 16 17 18 19 20 GND 2Q0 4F1 2Q1 GND VCCN 28 FB 6 3Q0 4F0 VCCN 5 3Q1 3F1 Pin Definitions Pin Name Pin Number I/O Description REF 1 I Reference frequency input. This input supplies the frequency and timing against which all functional variations are measured. FB 17 I PLL feedback input (typically connected to one of the eight outputs). FS 3 I Three-level frequency range select. See Table 1. 1F0, 1F1 26, 27 I Three-level function select inputs for output pair 1 (1Q0, 1Q1). See Table 2. 2F0, 2F1 29, 30 I Three-level function select inputs for output pair 2 (2Q0, 2Q1). See Table 2. 3F0, 3F1 4, 5 I Three-level function select inputs for output pair 3 (3Q0, 3Q1). See Table 2. 4F0, 4F1 6, 7 I Three-level function select inputs for output pair 4 (4Q0, 4Q1). See Table 2. TEST 31 I Three-level select. See test mode section under the block diagram descriptions. 1Q0, 1Q1 24, 23 O Output pair 1. See Table 2. 2Q0, 2Q1 20, 19 O Output pair 2. See Table 2. 3Q0, 3Q1 15, 14 O Output pair 3. See Table 2. 4Q0, 4Q1 11, 10 O VCCN 9, 16, 18, 25 PWR VCCQ 2, 8 PWR Power supply for internal circuitry. GND 12, 13, 21, 22, 28, 32 PWR Ground. Document Number: 38-07141 Rev. *L Output pair 4. See Table 2. Power supply for output drivers. Page 3 of 20 CY7B991V Block Diagram Description Skew Select Matrix The phase frequency detector and filter blocks accept inputs from the reference frequency (REF) input and the feedback (FB) input. They generate correction information to control the frequency of the voltage controlled oscillator (VCO). These blocks, along with the VCO, form a PLL that tracks the incoming REF signal. The skew select matrix is comprised of four independent sections. Each section has two low-skew, high fanout drivers (xQ0, xQ1), and two corresponding three-level function select (xF0, xF1) inputs. Table 2 shows the nine possible output functions for each section as determined by the function select inputs. All times are measured with respect to the REF input assuming that the output connected to the FB input has 0tU selected. VCO and Time Unit Generator Table 2. Programmable Skew Configurations [1] Phase Frequency Detector and Filter The VCO accepts analog control inputs from the PLL filter block. It generates a frequency that is used by the time unit generator to create discrete time units, selected in the skew select matrix. The operational range of the VCO is determined by the FS control pin. The time unit (tU) is determined by the operating frequency of the device and the level of the FS pin as shown in Table 1. Table 1. Frequency Range Select and tU fNOM (MHz) FS[2, 3] LOW Min Max 15 30 Calculation[1] 1 Approximate t U = -----------------------f NOM N Frequency (MHz) At Function Selects Output Functions 1F1, 2F1, 1F0, 2F0, 1Q0, 1Q1, 3F1, 4F1 3F0, 4F0 2Q0, 2Q1 -4tU 3Q0, 3Q1 4Q0, 4Q1 LOW LOW LOW MID -3tU -6tU -6tU LOW HIGH -2tU -4tU -4tU MID LOW -1tU -2tU -2tU MID MID 0tU 0tU 0tU Divide by 2 Divide by 2 MID HIGH +1tU +2tU +2tU where N = Which tU = 1.0 ns HIGH LOW +2tU +4tU +4tU 44 22.7 HIGH MID +3tU +6tU +6tU HIGH HIGH +4tU Divide by 4 Inverted MID 25 50 26 38.5 HIGH 40 80 16 62.5 Notes 1. For all three state inputs, HIGH indicates a connection to VCC, LOW indicates a connection to GND, and MID indicates an open connection. Internal termination circuitry holds an unconnected input to VCC/2. 2. The level to be set on FS is determined by the "normal" operating frequency (fNOM) of the VCO and Time Unit Generator (see Logic Block Diagram). Nominal frequency (fNOM) always appears at the outputs when they are operated in their undivided modes (see Table 2). The frequency appearing at the REF and FB inputs is fNOM when the output connected to FB is undivided. The frequency of the REF and FB inputs is fNOM/2 or fNOM/4 when the part is configured for a frequency multiplication using a divided output as the FB input. 3. When the FS pin is selected HIGH, the REF input must not transition upon power up until VCC has reached 2.8 V. Document Number: 38-07141 Rev. *L Page 4 of 20 CY7B991V Test Mode The TEST input is a three-level input. In normal system operation, this pin is connected to ground, allowing the CY7B991V to operate as explained in the Block Diagram Description on page 4. For testing purposes, any of the three-level inputs can have a removable jumper to ground or be tied LOW through a 100- resistor. This enables an external tester to change the state of these pins. If the TEST input is forced to its MID or HIGH state, the device operates with its internal phase locked loop disconnected, and input levels supplied to REF directly controls all outputs. Relative output to output functions are the same as in normal mode. In contrast with normal operation (TEST tied LOW), all outputs function based only on the connection of their own function select inputs (xF0 and xF1) and the waveform characteristics of the REF input. U U U U U U t 0 +1t t 0 +2t t 0 +3t t 0 +4t t 0 +5t t 0 +6t t0 t 0 - 1t U t 0 - 2t U t 0 - 3t U t 0 - 4t U t 0 - 5t U t 0 - 6t U Figure 2. Typical Outputs with FB Connected to a Zero Skew Output Test Mode [4] FBInput REFInput 1Fx 2Fx 3Fx 4Fx (N/A) LM - 6t U LL LH - 4t U LM (N/A) - 3t U LH ML - 2t U ML (N/A) - 1t U MM MM MH (N/A) +1t U HL MH +2t U HM (N/A) +3t U 0tU HH HL +4t U (N/A) HM +6t U (N/A) LL/HH DIVIDED (N/A) HH INVERT Note 4. FB connected to an output selected for "zero" skew (that is, xF1 = xF0 = MID). Document Number: 38-07141 Rev. *L Page 5 of 20 CY7B991V Operational Mode Descriptions Figure 3. Zero Skew and Zero Delay Clock Driver REF LOAD Z0 L1 FB REF FS SYSTEM CLOCK LOAD 4F0 4F1 4Q0 4Q1 3F0 3F1 3Q0 3Q1 2F0 2F1 2Q0 2Q1 1F0 1F1 1Q0 1Q1 L2 Z0 LOAD L3 Z0 L4 LOAD TEST Z0 LENGTH L1 = L2 = L3 = L4 Figure 2 shows the LVPSCB configured as a zero skew clock buffer. In this mode, the CY7B991V is the basis for a low-skew clock distribution tree. When all of the function select inputs (xF0, xF1) are left open, the outputs are aligned and drive a terminated transmission line to an independent load. The FB input is tied to any output in this configuration and the operating frequency range is selected with the FS pin. The low skew specification, coupled with the ability to drive terminated transmission lines (with impedances as low as 50 ), enables efficient printed circuit board design. Figure 4. Programmable Skew Clock Driver REF SYSTEM CLOCK FB REF FS 4F0 4F1 LOAD L1 Z0 LOAD 4Q0 4Q1 3F0 3F1 2F0 2F1 3Q0 3Q1 1F0 1F1 1Q0 1Q1 L2 Z0 LOAD L3 2Q0 2Q1 Z0 L4 LOAD TEST LENGTH L1 = L2 L3 < L2 by 6 inches L4 > L2 by 6 inches Figure 4 shows a configuration to equalize skew between metal traces of different lengths. In addition to low skew between outputs, the LVPSCB is programmed to stagger the timing of its outputs. The four groups of output pairs are each programmed to different output timing. Skew timing is adjusted over a wide range in small increments using the function select pins. In this configuration, the 4Q0 output is sent back to FB and configured for zero skew. The other three pairs of outputs are programmed to yield different skews relative to the feedback. By advancing the clock signal on the longer traces or retarding the clock signal on shorter traces, all loads receive the clock pulse at the same time. Figure 4 shows the FB input connected to an output with 0 ns skew (xF1, xF0 = MID) selected. The internal PLL synchronizes Document Number: 38-07141 Rev. *L Z0 the FB and REF inputs and aligns their rising edges to make certain that all outputs have precise phase alignment. Clock skews are advanced by 6 time units (tU) when using an output selected for zero skew as the feedback. A wider range of delays is possible if the output connected to FB is also skewed. Since "Zero Skew", +tU, and -tU are defined relative to output groups, and the PLL aligns the rising edges of REF and FB, wider output skews are created by proper selection of the xFn inputs. For example, a +10 tU between REF and 3Qx is achieved by connecting 1Q0 to FB and setting 1F0 = 1F1 = GND, 3F0 = MID, and 3F1 = High. (Since FB aligns at -4 tU, and 3Qx skews to +6 tU, a total of +10 tU skew is realized.) Many other configurations are realized by skewing both the outputs used as the FB input and skewing the other outputs. Page 6 of 20 CY7B991V Figure 5. Inverted Output Connections REF simultaneously and are out of phase on their rising edge. This enables the designer to use the rising edges of the 12 frequency and 14 frequency outputs without concern for rising edge skew. The 2Q0, 2Q1, 1Q0, and 1Q1 outputs run at 80 MHz and are skewed by programming their select inputs accordingly. Note that the FS pin is wired for 80 MHz operation as that is the frequency of the fastest output. FB REF FS Figure 7. Frequency Divider Connections 4F0 4F1 4Q0 4Q1 3F0 3F1 3Q0 3Q1 2F0 2F1 2Q0 2Q1 1F0 1F1 1Q0 1Q1 REF 20 MHz TEST 7B991V-11 Figure 5 shows an example of the invert function of the LVPSCB. In this example the 4Q0 output used as the FB input is programmed for invert (4F0 = 4F1 = HIGH) while the other three pairs of outputs are programmed for zero skew. When 4F0 and 4F1 are tied high, 4Q0 and 4Q1 become inverted zero phase outputs. The PLL aligns the rising edge of the FB input with the rising edge of the REF. This causes the 1Q, 2Q, and 3Q outputs to become the "inverted" outputs to the REF input. By selecting the output connected to FB, you can have two inverted and six non-inverted outputs or six inverted and two non-inverted outputs. The correct configuration is determined by the need for more (or fewer) inverted outputs. 1Q, 2Q, and 3Q outputs can also be skewed to compensate for varying trace delays independent of inversion on 4Q. Figure 6. Frequency Multiplier with Skew Connections REF 20 MHz FB REF FS 4F0 4F1 3F0 3F1 2F0 2F1 1F0 1F1 TEST 40 MHz 4Q0 4Q1 3Q0 3Q1 2Q0 2Q1 1Q0 1Q1 20 MHz 80 MHz 7B991V-12 Figure 6 shows the LVPSCB configured as a clock multiplier. The 3Q0 output is programmed to divide by four and is sent back to FB. This causes the PLL to increase its frequency until the 3Q0 and 3Q1 outputs are locked at 20 MHz, while the 1Qx and 2Qx outputs run at 80 MHz. The 4Q0 and 4Q1 outputs are programmed to divide by two that results in a 40 MHz waveform at these outputs. Note that the 20- and 40-MHz clocks fall Document Number: 38-07141 Rev. *L FB REF FS 4F0 4F1 4Q0 4Q1 10 MHz 3F0 3F1 2F0 2F1 3Q0 3Q1 5 MHz 1F0 1F1 TEST 1Q0 1Q1 2Q0 2Q1 20 MHz 7B991V-13 Figure 7 shows the LVPSCB in a clock divider application. 2Q0 is sent back to the FB input and programmed for zero skew. 3Qx is programmed to divide by four. 4Qx is programmed to divide by two. Note that the falling edges of the 4Qx and 3Qx outputs are aligned. This enables use of the rising edges of the 12 frequency and 14 frequency without concern for skew mismatch. The 1Qx outputs are programmed to zero skew and are aligned with the 2Qx outputs. In this example, the FS input is grounded to configure the device in the 15 to 30 MHz range since the highest frequency output is running at 20 MHz. Figure 8 on page 8 shows some of the functions that are selectable on the 3Qx and 4Qx outputs. These include inverted outputs and outputs that offer divide-by-2 and divide-by-4 timing. An inverted output enables the system designer to clock different subsystems on opposite edges without suffering from the pulse asymmetry typical of non-ideal loading. This function enables each of the two subsystems to clock 180 degrees out of phase, but still is aligned within the skew specification. The divided outputs offer a zero delay divider for portions of the system that divide the clock by either two or four, and still remain within a narrow skew of the "1X" clock. Without this feature, an external divider is added, and the propagation delay of the divider adds to the skew between the different clock signals. These divided outputs, coupled with the PLL, enable the LVPSCB to multiply the clock rate at the REF input by either two or four. This mode allows the designer to distribute a low frequency clock between various portions of the system. It also locally multiplies the clock rate to a more suitable frequency, while still maintaining the low skew characteristics of the clock driver. The LVPSCB performs all of the functions described in this section at the same time. It can multiply by two and four or divide by two (and four) at the same time that it shifts its outputs over a wide range or maintains zero skew between selected outputs. Page 7 of 20 CY7B991V Figure 8. Multi-Function Clock Driver REF LOAD Z0 80 MHz INVERTED FB REF FS 20 MHz DISTRIBUTION CLOCK 4F0 4F1 3F0 3F1 2F0 2F1 1F0 1F1 TEST LOAD 4Q0 4Q1 3Q0 3Q1 2Q0 2Q1 1Q0 1Q1 20 MHz Z0 LOAD 80 MHz ZERO SKEW Z0 80 MHz SKEWED -3.125 ns (-4tU) LOAD Z0 Figure 9. Board-to-Board Clock Distribution LOAD REF Z0 L1 FB SYSTEM CLOCK REF FS 4F0 4F1 LOAD Z0 L2 4Q0 4Q1 3F0 3F1 2F0 2F1 3Q0 3Q1 1F0 1F1 1Q0 1Q1 LOAD L3 2Q0 2Q1 Z0 L4 TEST Z0 FB REF FS 4F0 4F1 3F0 3F1 2F0 2F1 1F0 1F1 TEST 4Q0 4Q1 3Q0 3Q1 2Q0 2Q1 1Q0 1Q1 LOAD LOAD Figure 9 shows the CY7B991V connected in series to construct a zero skew clock distribution tree between boards. Delays of the downstream clock buffers are programmed to compensate for the wire length (that is, select negative skew equal to the wire delay) necessary to connect them to the master clock source, approximating a zero delay clock tree. Cascaded clock buffers accumulate low frequency jitter because of the non-ideal filtering characteristics of the PLL filter. Do not connect more than two clock buffers in a series. Document Number: 38-07141 Rev. *L Page 8 of 20 CY7B991V Maximum Ratings Output current into outputs (LOW) ............................. 64 mA Static discharge voltage (MIL-STD-883, Method 3015) .................................. >2001 V Operating outside these boundaries may affect the performance and life of the device. These user guidelines are not tested. Latch up current ...................................................... >200 mA Storage temperature .................................. -65 C to 150 C Operating Range Ambient temperature with power applied ..................................... -55 C to 125 C Range Supply voltage to ground potential ..............-0.5 V to +7.0 V Ambient Temperature Commercial DC input voltage ..........................................-0.5 V to +7.0 V Industrial VCC 0 C to 70 C 3.3 V 10% -40 C to 85 C 3.3 V 10% Electrical Characteristics Over the Operating Range Parameter [5] Description Test Conditions VOH Output HIGH voltage VCC = Min, IOH = -12 mA VOL Output LOW voltage VCC = Min, IOL = 35 mA VIH CY7B991V Min Max Unit 2.4 - V - 0.45 V Input HIGH voltage (REF and FB inputs only) 2.0 VCC V VIL Input LOW voltage (REF and FB inputs only) -0.5 0.8 V VIHH Three-level input HIGH Voltage (Test, FS, xFn) [6] Min VCC Max. 0.87 x VCC VCC V VIMM Three-level input MID voltage (Test, FS, xFn) [6] Min VCC Max. 0.47 x VCC 0.53 x VCC VILL Three-level input LOW voltage (Test, FS, xFn) [6] Min VCC Max. IIH Input HIGH leakage current (REF and FB inputs only) IIL V 0.0 0.13 x VCC V VCC = Max, VIN = Max. - 20 A Input LOW leakage current (REF and FB inputs only) VCC = Max, VIN = 0.4 V -20 - A IIHH Input HIGH current (Test, FS, xFn) VIN = VCC - 200 A IIMM Input MID current (Test, FS, xFn) VIN = VCC/2 -50 50 A IILL Input LOW current (Test, FS, xFn) VIN = GND -200 - A -200 - mA - 95 mA - 100 mA - 19 mA [7] IOS Short circuit current ICCQ Operating current used by internal circuitry VCCN = VCCQ = Max, All Input Selects Open ICCN Output buffer current per output pair [8] VCCN = VCCQ = Max, IOUT = 0 mA, Input Selects Open, fMAX VCC = Max, VOUT = GND (25 C only) Commercial Military / Industrial Notes 5. See the last page of this specification for Group A subgroup testing information. 6. These inputs are normally wired to VCC, GND, or left unconnected (actual threshold voltages vary as a percentage of VCC). Internal termination resistors hold unconnected inputs at VCC/2. If these inputs are switched, the function and timing of the outputs glitch and the PLL requires an additional tLOCK time before all datasheet limits are achieved. 7. CY7B991V is tested one output at a time, output shorted for less than one second, less than 10% duty cycle. Room temperature only. 8. Total output current per output pair is approximated by the following expression that includes device current plus load current: CY7B991V:ICCN = [(4 + 0.11F) + [((835 -3F)/Z) + (.0022FC)]N] x 1.1 Where F = frequency in MHz C = capacitive load in pF Z = line impedance in ohms N = number of loaded outputs; 0, 1, or 2 FC = F x C Document Number: 38-07141 Rev. *L Page 9 of 20 CY7B991V Electrical Characteristics (continued) Over the Operating Range Parameter [5] PD Description CY7B991V Test Conditions Power dissipation per output pair VCCN = VCCQ = Max, IOUT = 0 mA, Input Selects Open, fMAX Min Max - 104 Unit mW Capacitance Parameter [9, 10] Description Test Conditions Input capacitance CIN Max Unit 10 pF Test Conditions 32-pin PLCC Package Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, according to EIA/JESD51. 44 C/W 26 C/W TA = 25 C, f = 1 MHz, VCC = 3.3 V Thermal Resistance Parameter [10] JA Description Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) AC Test Loads and Waveforms Figure 10. AC Test Loads and Waveforms VCC R1 CL R2 3.0 V R1=100 R2=100 CL = 30 pF (Includes fixture and probe capacitance) TTL AC Test Load 2.0 V Vth =1.5 V 0.8 V 0.0 V ns 2.0 V Vth =1.5 V 0.8 V 1 ns TTL Input Test Waveform Notes 9. Applies to REF and FB inputs only. Tested initially and after any design or process changes that may affect these parameters. 10. Tested initially and after any design or process changes that may affect these parameters. Document Number: 38-07141 Rev. *L Page 10 of 20 CY7B991V Switching Characteristics (-2 option) Over the Operating Range Parameter [11, 12] fNOM CY7B991V-2 Description Operating clock Frequency in MHz Min Typ Max FS = LOW [11, 13] 15 - 30 FS = MID [11, 13] 25 - 50 FS = HIGH [11, 13, 14] Unit MHz 40 - 80 tRPWH REF pulse width HIGH measured at 1/2 x VCCQ threshold 3.65 - - ns tRPWL REF pulse width LOW measured at 1/2 x VCCQ threshold 3.65 - - ns tU Programmable skew unit tSKEWPR Zero output matched-pair skew (XQ0, XQ1)[15, 16] - 0.05 0.2 ns tSKEW0 Zero output skew (all outputs)[15, 17] - 0.1 0.25 ns - 0.1 0.5 ns - 0.5 1.0 ns - 0.25 0.5 ns - 0.5 0.9 ns See Table 1 outputs)[15, 18] tSKEW1 Output skew (rise-rise, fall-fall, same class tSKEW2 Output skew (rise-fall, nominal-inverted, divided-divided)[15, 18] outputs)[15, 18] tSKEW3 Output skew (rise-rise, fall-fall, different class tSKEW4 Output skew (rise-fall, nominal-divided, divided-inverted)[15, 18] skew[19, 20] tDEV Device-to-device tPD Propagation delay, REF rise to FB rise variation[21] tODCV Output duty cycle tPWH Output HIGH time deviation from 50%[22] tPWL Output LOW time deviation from 50%[22] tORISE Output rise time[22, 23] time[22, 23] tOFALL Output fall tLOCK PLL lock time[24] tJR Cycle-to-cycle output jitter - - 1.25 ns -0.25 0.0 +0.25 ns -0.65 0.0 +0.65 ns - - 2.0 ns - - 1.5 ns 0.15 1.0 1.2 ns 0.15 1.0 1.2 ns - - 0.5 ms RMS[19] - - 25 ps Peak[19] - 100 200 ps Notes 11. The level to be set on FS is determined by the "normal" operating frequency (fNOM) of the VCO and Time Unit Generator (see Logic Block Diagram). Nominal frequency (fNOM) always appears at the outputs when they are operated in their undivided modes (see Table 2). The frequency appearing at the REF and FB inputs is fNOM when the output connected to FB is undivided. The frequency of the REF and FB inputs is fNOM/2 or fNOM/4 when the part is configured for a frequency multiplication using a divided output as the FB input. 12. Test measurement levels for the CY7B991V are TTL levels (1.5 V to 1.5 V). Test conditions assume signal transition times of 2 ns or less and output loading as shown in the AC Test Loads and Waveforms unless otherwise specified. 13. For all three state inputs, HIGH indicates a connection to VCC, LOW indicates a connection to GND, and MID indicates an open connection. Internal termination circuitry holds an unconnected input to VCC/2. 14. When the FS pin is selected HIGH, the REF input must not transition upon power up until VCC has reached 2.8 V. 15. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with 30 pF and terminated with 50 to VCC/2 (CY7B991V). 16. tSKEWPR is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0tU. 17. tSKEW0 is defined as the skew between outputs when they are selected for 0tU. Other outputs are divided or inverted but not shifted. 18. There are three classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2 or Divide-by-4 mode). 19. Guaranteed by statistical correlation. Tested initially and after any design or process changes that may affect these parameters. 20. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC ambient temperature, air flow, etc.) 21. tODCV is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications. 22. Specified with outputs loaded with 30 pF for the CY7B991V-5 and -7 devices. Devices are terminated through 50 to VCC/2. tPWH is measured at 2.0 V. tPWL is measured at 0.8 V. 23. tORISE and tOFALL measured between 0.8 V and 2.0 V. 24. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits. Document Number: 38-07141 Rev. *L Page 11 of 20 CY7B991V Switching Characteristics (-5 Option) Over the Operating Range Parameter [25, 26] fNOM CY7B991V-5 Description Operating clock frequency in MHz Min Typ Max FS = LOW [25, 27] 15 - 30 FS = MID [25, 27] 25 - 50 FS = HIGH [25, 27] Unit MHz 40 - 80 tRPWH REF pulse width HIGH measured at 1/2 x VCCQ threshold 3.65 - - ns tRPWL REF pulse width LOW measured at 1/2 x VCCQ threshold 3.65 - - ns tU Programmable skew unit tSKEWPR Zero output matched-pair skew (XQ0, XQ1)[28, 29] - 0.1 0.25 ns tSKEW0 Zero output skew (all outputs)[28, 29] - 0.25 0.5 ns - 0.6 0.7 ns - 0.5 1.0 ns - 0.5 0.7 ns - 0.5 1.0 ns See Table 1 outputs)[28, 30] tSKEW1 Output skew (rise-rise, fall-fall, same class tSKEW2 Output skew (rise-fall, nominal-inverted, divided-divided)[28, 30] outputs)[28, 30] tSKEW3 Output skew (rise-rise, fall-fall, different class tSKEW4 Output skew (rise-fall, nominal-divided, divided-inverted)[28, 30] skew[32, 33] tDEV Device-to-device tPD Propagation delay, REF rise to FB rise variation[34] tODCV Output duty cycle tPWH Output HIGH time deviation from 50%[35] tPWL Output LOW time deviation from 50%[35] tORISE Output rise time[35, 36] Output fall tLOCK PLL lock time[36] tJR Cycle-to-cycle output jitter - 1.25 ns 0.0 +0.5 ns -1.0 0.0 +1.0 ns - - 2.5 ns - - 3 ns 0.15 1.0 1.5 ns 0.15 1.0 1.5 ns - - 0.5 ms RMS[32] - - 25 ps Peak-to-peak[32] - - 200 ps time[35, 36] tOFALL - -0.5 Notes 25. The level to be set on FS is determined by the "normal" operating frequency (fNOM) of the VCO and Time Unit Generator (see Logic Block Diagram). Nominal frequency (fNOM) always appears at the outputs when they are operated in their undivided modes (see Table 2). The frequency appearing at the REF and FB inputs is fNOM when the output connected to FB is undivided. The frequency of the REF and FB inputs is fNOM/2 or fNOM/4 when the part is configured for a frequency multiplication using a divided output as the FB input. 26. Test measurement levels for the CY7B991V are TTL levels (1.5 V to 1.5 V). Test conditions assume signal transition times of 2 ns or less and output loading as shown in the AC Test Loads and Waveforms unless otherwise specified. 27. For all three state inputs, HIGH indicates a connection to VCC, LOW indicates a connection to GND, and MID indicates an open connection. Internal termination circuitry holds an unconnected input to VCC/2. 28. tSKEWPR is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0tU. 29. tSKEW0 is defined as the skew between outputs when they are selected for 0tU. Other outputs are divided or inverted but not shifted. 30. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC ambient temperature, air flow, etc.) 31. CL = 0 pF. For CL = 30 pF, tSKEW0 = 0.35 ns. 32. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with 30 pF and terminated with 50 to VCC/2 (CY7B991V). 33. tODCV is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications. 34. Specified with outputs loaded with 30 pF for the CY7B991V-5 and -7 devices. Devices are terminated through 50 to VCC/2. tPWH is measured at 2.0 V. tPWL is measured at 0.8 V. 35. tORISE and tOFALL measured between 0.8 V and 2.0 V. 36. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits. Document Number: 38-07141 Rev. *L Page 12 of 20 CY7B991V Switching Characteristics (-7 Option) Over the Operating Range Parameter [37, 38] fNOM CY7B991V-7 Description Operating clock Frequency in MHz Min Typ Max FS = LOW [37, 39] 15 - 30 FS = MID [37, 39] 25 - 50 FS = HIGH [37, 39] Unit MHz 40 - 80 tRPWH REF pulse width HIGH measured at 1/2 x VCCQ threshold 3.65 - - ns tRPWL REF pulse width LOW measured at 1/2 x VCCQ threshold 3.65 - - ns tU Programmable skew unit tSKEWPR Zero output matched pair skew (XQ0, XQ1)[40, 41] - 0.1 0.25 ns tSKEW0 Zero output skew (All Outputs)[40, 42] - 0.3 0.75 ns - 0.6 1.0 ns - 1.0 1.5 ns - 0.7 1.2 ns - 1.2 1.7 ns See Table 1 outputs)[43, 44] tSKEW1 Output skew (rise-rise, fall-fall, same class tSKEW2 Output skew (rise-fall, nominal-inverted, divided-divided)[40, 45] outputs)[40, 45] tSKEW3 Output skew (rise-rise, fall-fall, different class tSKEW4 Output skew (rise-fall, nominal-divided, divided-inverted)[40, 45] skew[43, 46] tDEV Device-to-device tPD Propagation delay, REF rise to FB rise variation[46] tODCV Output duty cycle tPWH Output HIGH time deviation from 50%[47] tPWL Output LOW time deviation from 50%[47] tORISE Output rise time[47, 48] Output fall tLOCK PLL lock time[49] tJR Cycle-to-cycle output jitter - 1.65 ns 0.0 +0.7 ns -1.2 0.0 +1.2 ns - - 3 ns - - 3.5 ns 0.15 1.5 2.5 ns 0.15 1.5 2.5 ns - - 0.5 ms RMS[50] - - 25 ps Peak-to-peak[50] - - 200 ps time[47, 48] tOFALL - -0.7 Notes 37. The level to be set on FS is determined by the "normal" operating frequency (fNOM) of the VCO and Time Unit Generator (see Logic Block Diagram). Nominal frequency (fNOM) always appears at the outputs when they are operated in their undivided modes (see Table 2). The frequency appearing at the REF and FB inputs is fNOM when the output connected to FB is undivided. The frequency of the REF and FB inputs is fNOM/2 or fNOM/4 when the part is configured for a frequency multiplication using a divided output as the FB input. 38. Test measurement levels for the CY7B991V are TTL levels (1.5 V to 1.5 V). Test conditions assume signal transition times of 2 ns or less and output loading as shown in the AC Test Loads and Waveforms unless otherwise specified. 39. For all three state inputs, HIGH indicates a connection to VCC, LOW indicates a connection to GND, and MID indicates an open connection. Internal termination circuitry holds an unconnected input to VCC/2. 40. tSKEWPR is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0tU. 41. tSKEW0 is defined as the skew between outputs when they are selected for 0tU. Other outputs are divided or inverted but not shifted. 42. CL = 0 pF. For CL = 30 pF, tSKEW0 = 0.35 ns. 43. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with 30 pF and terminated with 50 to VCC/2 (CY7B991V). 44. There are three classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2 or Divide-by-4 mode). 45. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC ambient temperature, air flow, etc.) 46. tODCV is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications. 47. Specified with outputs loaded with 30 pF for the CY7B991V-5 and -7 devices. Devices are terminated through 50 to VCC/2. tPWH is measured at 2.0 V. tPWL is measured at 0.8 V. 48. tORISE and tOFALL measured between 0.8 V and 2.0 V. 49. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits. 50. Guaranteed by statistical correlation. Tested initially and after any design or process changes that may affect these parameters. Document Number: 38-07141 Rev. *L Page 13 of 20 CY7B991V AC Timing Diagrams tREF tRPWL tRPWH REF tODCV tPD tODCV FB tJR Q tSKEWPR, tSKEW0,1 tSKEWPR, tSKEW0,1 OTHER Q tSKEW2 tSKEW2 INVERTED Q tSKEW3,4 tSKEW3,4 tSKEW3,4 REF DIVIDED BY 2 tSKEW1,3, 4 tSKEW2,4 REF DIVIDED BY 4 Document Number: 38-07141 Rev. *L Page 14 of 20 CY7B991V Ordering Information Speed (ps) 250 500 Ordering Code Package Type Operating Range CY7B991V-2JC 32-pin PLCC Commercial CY7B991V-2JCT 32-pin PLCC - Tape and Reel Commercial CY7B991V-5JI 32-pin PLCC Industrial CY7B991V-5JIT 32-pin PLCC - Tape and Reel Industrial CY7B991V-2JXC 32-pin PLCC Commercial CY7B991V-2JXCT 32-pin PLCC - Tape and Reel Commercial CY7B991V-5JXC 32-pin PLCC Commercial CY7B991V-5JXCT 32-pin PLCC - Tape and Reel Commercial CY7B991V-5JXI 32-pin PLCC Industrial CY7B991V-5JXIT 32-pin PLCC - Tape and Reel Industrial CY7B991V-7JXC 32-pin PLCC Commercial CY7B991V-7JXCT 32-pin PLCC - Tape and Reel Commercial Pb-free 250 500 750 Ordering Code Definitions CY 7B991V - X J X X X X = blank or T blank = Tube; T = Tape and Reel Temperature Range: X = C or I C = Commercial = 0 C to +70 C; I = Industrial = -40 C to 85 C X = Pb-free; X Absent = Leaded Package Type: J = 32-pin PLCC Device Option (Performance): X = 2 or 5 or 7 Base Part Number Company ID: CY = Cypress Document Number: 38-07141 Rev. *L Page 15 of 20 CY7B991V Package Diagram Figure 11. 32-pin PLCC (0.453 x 0.553 Inches) J32 Package Outline, 51-85002 51-85002 *E Document Number: 38-07141 Rev. *L Page 16 of 20 CY7B991V Acronyms Document Conventions Table 3. Acronyms Used in this Document Units of Measure Acronym Description Table 4. Units of Measure CMOS Complementary Metal Oxide Semiconductor FB Feedback C degree Celsius LVPSCB Low-Voltage Programmable Skew Clock Buffer k kilohm LVTTL Low-Voltage Transistor-Transistor Logic A microampere PLL Phase-Locked Loop s microsecond PLCC Plastic Leaded Chip Carrier mA milliampere RF Reference Frequency ms millisecond mW milliwatt MHz megahertz ns nanosecond ohm pF picofarad ps picosecond V volt W watt RMS Root Mean Square VCO Voltage Controlled Oscillator Document Number: 38-07141 Rev. *L Symbol Unit of Measure Page 17 of 20 CY7B991V Document History Page Document Title: CY7B991V, 3.3 V RoboClock(R) Low Voltage Programmable Skew Clock Buffer Document Number: 38-07141 Revision ECN Submission Date Orig. of Change ** 110250 12/17/01 SZV Change from Specification number: 38-00641 to 38-07141. *A 293239 See ECN RGL Updated Features: Removed "Jitter < 200 ps peak-to-peak (< 25 ps RMS)". Added "Jitter 100 ps (typical)". Updated Switching Characteristics (-2 option): Added typical value of tJR parameter as "100 ps" corresponding to "Peak". Updated Ordering Information: Updated part numbers. *B 1199925 See ECN KVM / AESA Removed "Switching Characteristics (-2 option)". Updated Ordering Information: No change in part numbers. Changed format only. *C 1286064 See ECN AESA Change status from Preliminary to Final. *D 2584293 10/10/08 AESA Added Switching Characteristics (-2 option). Updated to new template. *E 2761988 09/10/09 CXQ Updated Test Mode: Replaced "100W resistor" with "100 resistor". Updated Ordering Information: No change in part numbers. Replaced "Pb" with "pin" in "Package Type" column. *F 2905834 04/06/2010 CXQ Updated Ordering Information: Removed inactive part numbers CY7B991V-5JC, CY7B991V-5JCT, CY7B991V-7JC and CY7B991V-7JCT. Updated Package Diagram. *G 3041840 09/29/2010 CXQ Fixed various format and typographical errors. Updated Pinouts: Updated Figure 1 (Fixed pin 8 label). Updated Pin Definitions: Added "Pin Number" column. Updated Electrical Characteristics: Removed values from "Max" column of ILL and IOS parameters and added the same values in "Min" column. Removed note "These inputs are normally wired to VCC, GND, or left unconnected (actual threshold voltages vary as a percentage of VCC). Internal termination resistors hold unconnected inputs at VCC/2. If these inputs are switched, the function and timing of the outputs may glitch and the PLL may require an additional tLOCK time before all datasheet limits are achieved." and its reference in "Description" column of PD parameter. *H 4161003 10/16/2013 CINM Updated Package Diagram: spec 51-85002 - Changed revision from *C to *D. Updated to new template. Completing Sunset Review. *I 4598452 12/16/2014 TAVA Updated Functional Description: Added "For a complete list of related resources, click here." at the end. Added AC Timing Diagrams. Document Number: 38-07141 Rev. *L Description of Change Page 18 of 20 CY7B991V Document History Page (continued) Document Title: CY7B991V, 3.3 V RoboClock(R) Low Voltage Programmable Skew Clock Buffer Document Number: 38-07141 Revision ECN Submission Date Orig. of Change *J 4644120 01/28/2015 TAVA Updated Switching Characteristics (-2 option): Updated description of tRPWH and tRPWL parameters. Changed minimum value of tRPWH parameter from 5 ns to 3.65 ns. Changed minimum value of tRPWL parameter from 5 ns to 3.65 ns. Updated Switching Characteristics (-5 Option): Updated description of tRPWH and tRPWL parameters. Changed minimum value of tRPWH parameter from 5 ns to 3.65 ns. Changed minimum value of tRPWL parameter from 5 ns to 3.65 ns. Updated Switching Characteristics (-7 Option): Updated description of tRPWH and tRPWL parameters. Changed minimum value of tRPWH parameter from 5 ns to 3.65 ns. Changed minimum value of tRPWL parameter from 5 ns to 3.65 ns. Updated Package Diagram: spec 51-85002 - Changed revision from *D to *E. *K 5276098 05/18/2016 PSR Updated Electrical Characteristics: Updated Note 8 (Replaced "FC = F < C" with "FC = F x C"). Added Thermal Resistance. Updated to new template. *L 5507104 11/02/2016 PAWK Document Number: 38-07141 Rev. *L Description of Change Updated Sales, Solutions, and Legal Information and added WICED in the copyright notice. Page 19 of 20 CY7B991V Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC(R)Solutions Products ARM(R) Cortex(R) Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers cypress.com/clocks Interface Cypress Developer Community Forums | Projects | Video | Blogs | Training | Components cypress.com/interface Internet of Things Lighting & Power Control PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP cypress.com/iot cypress.com/powerpsoc Memory PSoC Touch Sensing USB Controllers Wireless/RF Technical Support cypress.com/support cypress.com/memory cypress.com/psoc cypress.com/touch cypress.com/usb cypress.com/wireless (c) Cypress Semiconductor Corporation, 2001-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 38-07141 Rev. *L Revised November 2, 2016 Page 20 of 20