DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 DS15MB200 Dual 1.5 Gbps 2:1/1:2 LVDS Mux/Buffer with Pre-Emphasis Check for Samples: DS15MB200 FEATURES DESCRIPTION * * The DS15MB200 is a dual-port 2 to 1 multiplexer and 1 to 2 repeater/buffer. High-speed data paths and flow-through pinout minimize internal device jitter and simplify board layout, while pre-emphasis overcomes ISI jitter effects from lossy backplanes and cables. The differential inputs and outputs interface to LVDS or Bus LVDS signals such as those on Texas Instrument's 10-, 16-, and 18-bit Bus LVDS SerDes, or to CML or LVPECL signals. 1 2 * * * * * * * * 1.5 Gbps Data Rate Per Channel Configurable Off/On Pre-emphasis Drives Lossy Backplanes and Cables LVDS/BLVDS/CML/LVPECL Compatible Inputs, LVDS Compatible Outputs Low Output Skew and Jitter On-chip 100 Input and Output Termination 15 kV ESD Protection on LVDS Inputs/Outputs Hot Plug Protection Single 3.3V Supply Industrial -40 to +85C Temperature Range 48-pin WQFN Package The 3.3V supply, CMOS process, and robust I/O ensure high performance at low power over the entire industrial -40 to +85C temperature range. Switch Fabric B Mux Buffer LVDS LVDS Switch Fabric A Backplane or Cable Typical Application FPGA or ASIC Figure 1. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com Block Diagram PREA_0 ENA_0 PREB_0 ENB_0 SOA_0 LI_0 SOB_0 PREL_0 ENL_0 SIA_0 LO_0 SIB_0 MUX_S0 Channel 0 Channel 1 Figure 2. PIN DESCRIPTIONS Pin Name WQFN Pin Number I/O, Type Description SWITCH SIDE DIFFERENTIAL INPUTS SIA_0+ SIA_0- 30 29 I, LVDS Switch A-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. SIA_1+ SIA_1- 19 20 I, LVDS Switch A-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. SIB_0+ SIB_0- 28 27 I, LVDS Switch B-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. SIB_1+ SIB_1- 21 22 I, LVDS Switch B-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. LINE SIDE DIFFERENTIAL INPUTS LI_0+ LI_0- 40 39 I, LVDS Line-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. LI_1+ LI_1- 9 10 I, LVDS Line-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or LVPECL compatible. SWITCH SIDE DIFFERENTIAL OUTPUTS SOA_0+ SOA_0- 34 33 O, LVDS Switch A-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2). SOA_1+ SOA_1- 15 16 O, LVDS Switch A-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2). SOB_0+ SOB_0- 32 31 O, LVDS Switch B-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2). SOB_1+ SOB_1- 17 18 O, LVDS Switch B-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2). LINE SIDE DIFFERENTIAL OUTPUTS LO_0+ LO_0- 42 41 O, LVDS Line-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2). LO_1+ LO_1- 7 8 O, LVDS Line-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2). (1) (2) 2 For interfacing LVDS outputs to CML or LVPECL compatible inputs, refer to the applications section of this datasheet (planned). The LVDS outputs do not support a multidrop (BLVDS) environment. The LVDS output characteristics of the DS15MB200 device have been optimized for point-to-point backplane and cable applications. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 PIN DESCRIPTIONS (continued) Pin Name WQFN Pin Number I/O, Type Description DIGITAL CONTROL INTERFACE MUX_S0 MUX_S1 38 11 I, LVTTL Mux Select Control Inputs (per channel) to select which Switch-side input, A or B, is passed through to the Line-side. PREA_0 PREA_1 PREB_0 PREB_1 26 23 25 24 I, LVTTL Output pre-emphasis control for Switch-side outputs. Each output driver on the Switch A-side and Bside has a separate pin to control the pre-emphasis on or off. PREL_0 PREL_1 44 5 I, LVTTL Output pre-emphasis control for Line-side outputs. Each output driver on the Line A-side and B-side has a separate pin to control the pre-emphasis on or off. ENA_0 ENA_1 ENB_0 ENB_1 36 13 35 14 I, LVTTL Output Enable Control for Switch A-side and B-side outputs. Each output driver on the A-side and B-side has a separate enable pin. ENL_0 ENL_1 45 4 I, LVTTL Output Enable Control for The Line-side outputs. Each output driver on the Line-side has a separate enable pin. VDD 2, 6, 12, 37, 43, 46, 48 I, Power VDD = 3.3V 0.3V. GND 3, 47 (3) I, Power Ground reference for LVDS and CMOS circuitry. For the WQFN package, the DAP is used as the primary GND connection to the device. The DAP is the exposed metal contact at the bottom of the WQFN-48 package. It should be connected to the ground plane with at least 4 vias for optimal AC and thermal performance. POWER (3) Note that the DAP on the backside of the WQFN package is the primary GND connection for the device when using the WQFN package. VDD N/C VDD GND 1 48 ENL_1 2 PREL_1 N/C 3 VDD VDD 4 LO-1+ GND 5 LO_1- ENL_1 6 LI_1+ PREL_1 7 LI_1- VDD 8 MUX_S1 LO-1+ 9 VDD LO_1- LI_1- 12 11 10 13 LI_1+ ENA_1 MUX_S1 VDD Connection Diagrams VDD ENA_1 Channel 1 47 15 46 VDD SOA_1+ VDD SOA_1- 16 45 ENL_0 SOA_1- ENL_0 SOB_1+ 17 44 PREL_0 SOB_1+ SOB_1- 18 43 VDD SOB_1- VDD SIA_1+ 19 42 LO_0+ SIA_1+ LO_0+ SIA_1- 20 41 LO_0- SIA_1- LO_0- SIB_1+ 21 40 LI_0+ SIB_1+ LI_0+ SIB_1- 22 39 LI_0- SIB_1- LI_0- PREA_1 23 38 MUX_S0 PREA_1 MUX_S0 PREB_1 37 24 25 26 27 28 29 30 31 32 33 34 35 36 VDD PREB_1 VDD Figure 3. WQFN Top View DAP = GND ENB_1 GND PREL_0 ENA_0 ENB_0 SOA_0+ SOA_0- SOB_0+ SOB_0- SIA_0+ SIA_0- SIB_0+ SIB_0- PREA_0 Channel 0 PREB_0 ENB_0 SOA_0+ SOA_0- SOB_0+ SOB_0- SIA_0+ SIA_0- SIB_0+ SIB_0- PREA_0 DAP (GND) ENA_0 14 SOA_1+ PREB_0 ENB_1 GND Figure 4. Directional Signal Paths Top View (Refer to pin names for signal polarity) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 3 DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com Output Characteristics The output characteristics of the DS15MB200 have been optimized for point-to-point backplane and cable applications, and are not intended for multipoint or multidrop signaling. A 100 output (source) termination resistor is incorporated in the device to eliminate the need for an external resistor, providing excellent drive characteristics by locating the source termination as close to the output as physically possible. Pre-Emphasis Controls The pre-emphasis is used to compensate for long or lossy transmission media. Separate pins are provided for each output to minimize power consumption. Pre-emphasis is programmable to be off or on per the Preemphasis Control Table. (1) PREx_n (1) Output Pre-Emphasis 0 0% 1 100% Applies to PREA_0, PREA_1, PREB_0, PREB_1, PREL_0, PREL_1 Multiplexer Truth Table (2) (3) Data Inputs (2) (3) Control Inputs Output SIA_0 SIB_0 MUX_S0 ENL_0 LO_0 X valid 0 1 SIB_0 valid X 1 1 SIA_0 X X X 0 Z Same functionality for channel 1 X = Don't Care Z = High Impedance (TRI-STATE) Repeater/Buffer Truth Table (1) (2) Data Input (1) (2) Control Inputs Outputs LI_0 ENA_0 ENB_0 SOA_0 SOB_0 X 0 0 Z Z valid 0 1 Z LI_0 valid 1 0 LI_0 Z valid 1 1 LI_0 LI_0 Same functionality for channel 1 X = Don't Care Z = High Impedance (TRI-STATE) These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 4 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 Absolute Maximum Ratings (1) Value Unit Supply Voltage (VDD) -0.3 to +4.0 V CMOS Input Voltage -0.3 to (VDD+0.3) V -0.3 to (VDD+0.3) V LVDS Receiver Input Voltage (2) LVDS Driver Output Voltage -0.3 to (VDD+0.3) V +40 mA Junction Temperature +150 C Storage Temperature -65 to +150 C Lead Temperature (Solder, 4sec) 260 C Max Pkg Power Capacity @ 25C 5.2 W Thermal Resistance (JA) 24 C/W 41.7 mW/C 8 kV 15 kV 250 V 1000 V LVDS Output Short Circuit Current Package Derating above +25C HBM, 1.5k, 100pF LVDS pins to GND only ESD Last Passing Voltage EIAJ, 0, 200pF CDM (1) (2) Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Texas Instruments does not recommend operation of products outside of recommended operation conditions. VID max < 2.4V Recommended Operating Conditions Min Supply Voltage (VCC) Input Voltage (VI) (1) Output Voltage (VO) Operating Temperature (TA) Industrial (1) Max Unit 3.0 3.6 V 0 VCC V 0 VCC V -40 +85 C VID max < 2.4V Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 5 DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com Electrical Characteristics Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter Conditions Min Typ (1) Max Units V LVTTL DC SPECIFICATIONS (MUX_Sn, PREA_n, PREB_n, PREL_n, ENA_n, ENB_n, ENL_n) VIH High Level Input Voltage 2.0 VDD VIL Low Level Input Voltage GND 0.8 V IIH High Level Input Current VIN = VDD = VDDMAX -10 +10 A IIHR High Level Input Current PREA_n, PREB_n, PREL_n 40 200 A IIL Low Level Input Current VIN = VSS, VDD = VDDMAX -10 +10 A CIN1 Input Capacitance Any Digital Input Pin to VSS COUT1 Output Capacitance Any Digital Output Pin to VSS VCL Input Clamp Voltage ICL = -18 mA -1.5 2.0 pF 4.0 pF -0.8 V LVDS INPUT DC SPECIFICATIONS (SIA, SIB, LI) Differential Input High Threshold (2) VTH (2) VCM = 0.8V or 1.2V or 3.55V, VDD = 3.6V 0 VCM = 0.8V or 1.2V or 3.55V, VDD = 3.6V 100 mV VTL Differential Input Low Threshold VID Differential Input Voltage VCM = 0.8V to 3.55V, VDD = 3.6V 100 2400 VCMR Common Mode Voltage Range VID = 150 mV, VDD = 3.6V 0.05 3.55 CIN2 Input Capacitance IN+ or IN- to VSS IIN Input Current VIN = 3.6V, VDD = VDDMAX or 0V -15 +15 A VIN = 0V, VDD = VDDMAX or 0V -15 +15 A 500 mV 35 mV 1.475 V 35 mV -40 mA -100 0 mV 2.0 mV V pF LVDS OUTPUT DC SPECIFICATIONS (SOA_n, SOB_n, LO_n) VOD Differential Output Voltage, 0% Pre-emphasis (2) RL is the internal 100 between OUT+ and OUT- VOD Change in VOD between Complementary States -35 VOS Offset Voltage (3) 1.05 VOS Change in VOS between Complementary States -35 IOS Output Short Circuit Current OUT+ or OUT- Short to GND -21 COUT2 Output Capacitance OUT+ or OUT- to GND when TRISTATE 4.0 All inputs and outputs enabled and active, terminated with external load of 100 between OUT+ and OUT-. 225 275 mA ENA_0 = ENB_0 = ENL_0 = ENA_1 = ENB_1 = ENL_1 = L 0.6 4.0 mA 170 250 ps 170 250 ps 1.0 2.5 ns 1.0 2.5 ns 250 360 1.22 pF SUPPLY CURRENT (Static) ICC Supply Current ICCZ Supply Current - Powerdown Mode SWITCHING CHARACTERISTICS--LVDS OUTPUTS tLHT Differential Low to High Transition Time tHLT Differential High to Low Transition Time tPLHD Differential Low to High Propagation Delay tPHLD Differential High to Low Propagation Delay tSKD1 Pulse Skew |tPLHD-tPHLD| (4) 25 75 ps tSKCC Output Channel to Channel Skew Difference in propagation delay (tPLHD or tPHLD) among all output channels. (4) 50 115 ps (1) (2) (3) (4) 6 Use an alternating 1 and 0 pattern at 200 Mb/s, measure between 20% and 80% of VOD. (4) Use an alternating 1 and 0 pattern at 200 Mb/s, measure at 50% VOD between input to output. Typical parameters are measured at VDD = 3.3V, TA = 25C. They are for reference purposes, and are not production-tested. Differential output voltage VOD is defined as ABS(OUT+-OUT-). Differential input voltage VID is defined as ABS(IN+-IN-). Output offset voltage VOS is defined as the average of the LVDS single-ended output voltages at logic high and logic low states. Not production tested. Guaranteed by statistical analysis on a sample basis at the time of characterization. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 Electrical Characteristics (continued) Over recommended operating supply and temperature ranges unless other specified. Symbol tJIT Parameter Jitter (0% Pre-emphasis) Conditions (5) RJ - Alternating 1 and 0 at 750MHz Min (6) Typ (1) Max Units 1.1 1.5 psrms DJ - K28.5 Pattern, 1.5 Gbps (7) 20 34 psp-p TJ - PRBS 27-1 Pattern, 1.5 Gbps (8) 14 28 psp-p tON LVDS Output Enable Time Time from ENA_n, ENB_n, or ENL_n to OUT change from TRI-STATE to active. 0.5 1.5 s tON2 LVDS Output Enable Time from Powerdown Mode Time from ENA_n, ENB_n, or ENL_n to OUT change from Powerdown Mode to active. 10 20 s LVDS Output Disable Time Time from ENA_n, ENB_n, or ENL_n to OUT change from active to TRI-STATE or Powerdown mode. 12 ns tOFF (5) (6) (7) (8) Jitter is not production tested, but guaranteed through characterization on a sample basis. Random Jitter, or RJ, is measured RMS with a histogram including 1500 histogram window hits. The input voltage = VID = 500mV, 50% duty cycle at 750MHz, tr = tf = 50ps (20% to 80%). Deterministic Jitter, or DJ, is measured to a histogram mean with a sample size of 350 hits. Stimulus and fixture jitter have been subtracted. The input voltage = VID = 500mV, K28.5 pattern at 1.5 Gbps, tr = tf = 50ps (20% to 80%). The K28.5 pattern is repeating bit streams of (0011111010 1100000101). Total Jitter, or TJ, is measured peak to peak with a histogram including 3500 window hits. Stimulus and fixture jitter have been subtracted. The input voltage = VID = 500mV, 27-1 PRBS pattern at 1.5 Gbps, tr = tf = 50ps (20% to 80%). Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 7 DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com WQFN Performance Characteristics Power Supply Current vs. Bit Data Rate 300 250 200 Total Jitter vs. Bit Data Rate 60 50 PRE-EMPHASIS ON TOTAL JITTER (ps) POWER SUPPLY CURRENT (mA) 350 PRE-EMPHASIS OFF 150 100 40 30 VCM = 1.2V 20 VCM = 0.25V 10 50 VCM = 3.0V 0 0 0 500 1000 2000 1500 0 500 BIT DATA RATE (Mbps) 1000 1500 2000 BIT DATA RATE (Mbps) Total Jitter measured at 0V differential while running a PRBS 27-1 pattern with one channel active, all other channels are disabled. VDD = 3.3V, TA = +25C, VID = 0.5V, pre-emphasis off. Dynamic power supply current was measured with all channels active and toggling at the bit data rate. Data pattern has no effect on the power consumption. VDD = 3.3V, TA = +25C, VID = 0.5V, VCM = 1.2V Figure 5. Figure 6. Total Jitter vs. Temperature 30 TOTAL JITTER (ps) 25 20 15 10 5 0 -40 0 -20 20 40 60 80 100 TEMPERATURE (C) 7 Total Jitter measured at 0V differential while running a PRBS 2 -1 pattern with one channel active, all other channels are disabled. VDD = 3.3V, VID = 0.5V, VCM = 1.2V, 1.5 Gbps data rate, pre-emphasis off. Figure 7. 8 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 TRI-STATE AND POWERDOWN MODES The DS15MB200 has output enable control on each of the six onboard LVDS output drivers. This control allows each output individually to be placed in a low power TRI-STATE mode while the device remains active, and is useful to reduce power consumption on unused channels. In TRI-STATE mode, some outputs may remain active while some are in TRI-STATE. When all six of the output enables (all drivers on both channels) are deasserted (LOW), then the device enters a Powerdown mode that consumes only 0.5mA (typical) of supply current. In this mode, the entire device is essentially powered off, including all receiver inputs, output drivers and internal bandgap reference generators. When returning to active mode from Powerdown mode, there is a delay until valid data is presented at the outputs because of the ramp to power up the internal bandgap reference generators. Any single output enable that remains active will hold the device in active mode even if the other five outputs are in TRI-STATE. When in Powerdown mode, any output enable that becomes active will wake up the device back into active mode, even if the other five outputs are in TRI-STATE. Input Failsafe Biasing External pull up and pull down resistors may be used to provide enough of an offset to enable an input failsafe under open-circuit conditions. This configuration ties the positive LVDS input pin to VDD thru a pull up resistor and the negative LVDS input pin is tied to GND by a pull down resistor. The pull up and pull down resistors should be in the 5k to 15k range to minimize loading and waveform distortion to the driver. The commonmode bias point ideally should be set to approximately 1.2V (less than 1.75V) to be compatible with the internal circuitry. Please refer to application note AN-1194, "Failsafe Biasing of LVDS Interfaces" (SNLA051) for more information. Interfacing LVPECL to LVDS An LVPECL driver consists of a differential pair with coupled emitters connected to GND via a current source. This drives a pair of emitter-followers that require a 50 ohm to VCC-2.0 load. A modern LVPECL driver will typically include the termination scheme within the device for the emitter follower. If the driver does not include the load, then an external scheme must be used. The 1.3 V supply is usually not readily available on a PCB, therefore, a load scheme without a unique power supply requirement may be used. 50: 15MB200 LVPECL 50: R1 150: R2 150: Figure 8. DC Coupled LVPECL to LVDS Interface Figure 8 is a separated termination scheme for a 3.3 V LVPECL driver. R1 and R2 provides proper DC load for the driver emitter followers, and may be included as part of the driver device (1). The DS15MB200 includes a 100 ohm input termination for the transmission line. The common mode voltage will be at the normal LVPECL levels - around 2 V. This scheme works well with LVDS receivers that have rail-to-rail common mode voltage, VCM, range. Most Texas Instrument's LVDS receivers have wide VCM range. The exceptions are noted in devices' respective datasheets. Those LVDS devices that do have a wide VCM range do not vary in performance significantly when receiving a signal with a common mode other than standard LVDS VCM of 1.2 V. (1) The bias networks shown above for LVPECL drivers and receivers may or may not be present within the driver device. The LVPECL driver and receiver specification must be reviewed closely to ensure compatibility between the driver and receiver terminations and common mode operating ranges. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 9 DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com 0.1 PF 50: 15MB200 LVPECL 50: R1 150: 0.1 PF R2 150: Figure 9. AC Coupled LVPECL to LVDS Interface An AC coupled interface is preferred when transmitter and receiver ground references differ more than 1 V. This is a likely scenario when transmitter and receiver devices are on separate PCBs. Figure 9 illustrates an AC coupled interface between a LVPECL driver and LVDS receiver. R1 and R2, if not present in the driver device(2), provide DC load for the emitter followers and may range between 140-220 ohms for most LVPECL devices for this particular configuration. The DS15MB200 includes an internal 100 ohm resistor to terminate the transmission line for minimal reflections. The signal after AC coupling capacitors will swing around a level set by internal biasing resistors (i.e. fail-safe) which is either VDD/2 or 0 V depending on the actual failsafe implementation. If internal biasing is not implemented, the signal common mode voltage will slowly wander to GND level. Interfacing LVDS to LVPECL An LVDS driver consists of a current source (nominal 3.5mA) which drives a CMOS differential pair. It needs a differential resistive load in the range of 70 to 130 ohms to generate LVDS levels. In a system, the load should be selected to match transmission line characteristic differential impedance so that the line is properly terminated. The termination resistor should be placed as close to the receiver inputs as possible. When interfacing an LVDS driver with a non-LVDS receiver, one only needs to bias the LVDS signal so that it is within the common mode range of the receiver. This may be done by using separate biasing voltage which demands another power supply. Some receivers have required biasing voltage available on-chip (VT, VTT or VBB). 50: LVPECL 15MB200 50: R1 50: R2 50: VT Figure 10. DC Coupled LVDS to LVPECL Interface Figure 10 illustrates interface between an LVDS driver and a LVPECL with a VT pin available. R1 and R2, if not present in the receiver (2), provide proper resistive load for the driver and termination for the transmission line, and VT sets desired bias for the receiver. (2) 10 The bias networks shown above for LVPECL drivers and receivers may or may not be present within the driver device. The LVPECL driver and receiver specification must be reviewed closely to ensure compatibility between the driver and receiver terminations and common mode operating ranges. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 DS15MB200 www.ti.com SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 VDD 0.1 PF R1 83: R2 83: 50: LVPECL 15MB200 50: 0.1 PF R3 130: R4 130: Figure 11. AC Coupled LVDS to LVPECL Interface Figure 11 illustrates AC coupled interface between an LVDS driver and LVPECL receiver without a VT pin available. The resistors R1, R2, R3, and R4, if not present in the receiver (2), provide a load for the driver, terminate the transmission line, and bias the signal for the receiver. Packaging Information The Leadless Leadframe Package (WQFN) is a leadframe based chip scale package (CSP) that may enhance chip speed, reduce thermal impedance, and reduce the printed circuit board area required for mounting. The small size and very low profile make this package ideal for high density PCBs used in small-scale electronic applications such as cellular phones, pagers, and handheld PDAs. The WQFN package is offered in the no Pullback configuration. In the no Pullback configuration the standard solder pads extend and terminate at the edge of the package. This feature offers a visible solder fillet after board mounting. The WQFN has the following advantages: * Low thermal resistance * Reduced electrical parasitics * Improved board space efficiency * Reduced package height * Reduced package mass For more details about WQFN packaging technology, refer to applications note AN-1187, "Leadless Leadframe Package" (SNOA401). Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 11 DS15MB200 SNLS196E - NOVEMBER 2005 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision D (March 2013) to Revision E * 12 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 11 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS15MB200 PACKAGE OPTION ADDENDUM www.ti.com 4-Nov-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS15MB200TSQ/NOPB ACTIVE WQFN RHS 48 250 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 15M200 DS15MB200TSQX/NOPB ACTIVE WQFN RHS 48 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 15M200 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 4-Nov-2016 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DS15MB200TSQ/NOPB WQFN RHS 48 250 178.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1 DS15MB200TSQX/NOPB WQFN RHS 48 2500 330.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS15MB200TSQ/NOPB WQFN RHS DS15MB200TSQX/NOPB WQFN RHS 48 250 210.0 185.0 35.0 48 2500 367.0 367.0 38.0 Pack Materials-Page 2 PACKAGE OUTLINE RHS0048A WQFN - 0.8 mm max height SCALE 1.800 PLASTIC QUAD FLATPACK - NO LEAD 7.15 6.85 A B PIN 1 INDEX AREA 0.5 0.3 7.15 6.85 0.30 0.18 DETAIL OPTIONAL TERMINAL TYPICAL 0.8 0.7 C SEATING PLANE 0.05 0.00 0.08 C 2X 5.5 (0.2) 5.1 0.1 (A) TYP 24 13 44X 0.5 DIM A OPT 1 OPT 2 (0.1) (0.2) 12 25 EXPOSED THERMAL PAD 2X 5.5 49 SYMM SEE TERMINAL DETAIL 1 PIN 1 ID (OPTIONAL) 36 48 37 SYMM 48X 0.5 0.3 48X 0.30 0.18 0.1 0.05 C A B 4214990/B 04/2018 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance. www.ti.com EXAMPLE BOARD LAYOUT RHS0048A WQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD ( 5.1) SYMM 37 48 48X (0.6) 1 36 48X (0.25) (1.05) TYP 44X (0.5) (1.25) TYP 49 SYMM (6.8) (R0.05) TYP ( 0.2) TYP VIA 25 12 13 24 (1.25) TYP (1.05) TYP (6.8) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:12X 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND SOLDER MASK OPENING METAL EDGE EXPOSED METAL SOLDER MASK OPENING EXPOSED METAL NON SOLDER MASK DEFINED (PREFERRED) METAL UNDER SOLDER MASK SOLDER MASK DEFINED SOLDER MASK DETAILS 4214990/B 04/2018 NOTES: (continued) 4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). 5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view. It is recommended that vias under paste be filled, plugged or tented. www.ti.com EXAMPLE STENCIL DESIGN RHS0048A WQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD (0.625) TYP (1.25) TYP 37 48 48X (0.6) 1 36 49 48X (0.25) 44X (0.5) (1.25) TYP (0.625) TYP SYMM (6.8) (R0.05) TYP METAL TYP 25 12 13 16X ( 1.05) 24 SYMM (6.8) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL EXPOSED PAD 49 68% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE SCALE:15X 4214990/B 04/2018 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DS15MB200TSQ DS15MB200TSQ/NOPB DS15MB200TSQX/NOPB