Datasheet
○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays
1/6
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・14・001
Clockless Link Interface LSI
24bit Clockless Link
Transmitter
BU17101AKV-M
●
●●
●General Description
BU17101AKV-M is a differential serial interface IC that
expect further low power consumption and low EMI by
ROHM's original CDR(Clock Data Recovery) technology.
The BU17101AKV-M transmitter serializes 24-bit
CMOS level signals, and transfers by the differential
lines of 1 pair. There is no return path. Reset line and
link synchronous control line are unnecessary. The
BU17101AKV-M links automatically.
●
●●
●Features
■ High-speed differential serial interface (Maximum
1.6Gbps)
■ Embedded clock interface
■ No lock condition signal and no reset signal between
transmitter and receiver. (Only differential signals)
■ Low EMI transmission by original DC balance protocol
and scrambling.
●
●●
●Applications
■ Car navigation display interface
■ Printer display interface
●
●●
●Key Specifications
I/O voltage range: 2.3 to 3.6 V
3.3V voltage range: 2.3 to 3.6 V
Clock frequency range: 30M to 51M Hz
Transmission data rate: 0.960G to 1.630 Gbps
Effective throughput: 0.720G to 1.224 Gbps
Operating temperature range: -40 to +85 ℃
●
●●
●Package W(Typ.) x D(Typ.) x H(Max.)
VQFP48 9.00mm x 9.00mm x 1.63mm
Datasheet
2/6
BU17101AKV-M
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・15・001
●
●●
●Block Diagram
Encode
Parallel to Serial
Input Buffer
PLL Timing GenPCLK
PD[23:0]
BU17101AKV-M (Tx)
DFTX+
DFTX-
Operation ControlDFSET[1:0]
PLLBW[1:0]
TESTPT
VDDIO
REG RVDD
GND
Parallel I/O Interface
PD[23:0]
PCLK
ERR
VDD33
TEST[1:0]
POL
Figure 1. Block Diagram
Datasheet
3/6
BU17101AKV-M
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・15・001
●
●●
●Typical Application Circuit
PCLK
PD[23:0]
BU17101AKV-M (Tx)
DFTX+
DFTX-
DFRX+(-)
DFRX-(+) PCLK
PD[23:0]
DFSET1 TEST1
RVDD
POL
TEST0
TESTPT
VDD33
GND
VDDIO
DFSET0
PLLBW0
RVDD
GND
VDDIO
TEST1
POL
TEST0
TESTPT
リセット(Tx)
ストリーム
データ
3.3V
-
+
ストリーム
データ
3.3V
-
+
OE
F_XS
BU17102AKV-M (Rx)
0.1uF
0.1uF
VDD33
0.01uF
0.47uF 0.1uF x 2
1uF
0.01uF
0.47uF
0.1uF x 3
ERR ERR
(47uF) (47uF)
リセット(Rx)
0.1uF x 20.1uF x 2
0.1uF
0.1uF
PLLBW1
PLLBW1
PLLBW0
Figure 2. Typical Application Circuit
Stream
Data
Stream
Data
Reset(Tx)
Reset(Rx)
Datasheet
4/6
BU17101AKV-M
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・15・001
●
●●
●Ordering Information
B
U
1
7
1
0
1
A
K
V
-
M
E
2
Package
KV: VQFP48
Packaging and forming specification
E2: Embossed tape and reel
Part No.
●
●●
●Marking Diagram
VQFP48 (TOP VIEW)
BU17101A
Part Number Marking
LOT Number
1PIN MARK
Datasheet
5/6
BU17101AKV-M
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・15・001
●
●●
●Physical Dimension Tape and Reel Information
Package Name VQFP48
Direction of feed
Reel ∗ Order quantity needs to be multiple of the minimum quantity.
<Tape and Reel information>
Embossed carrier tapeTape
Quantity
Direction
of feed The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
1500pcs
E2
( )
1pin
Datasheet
6/6
BU17101AKV-M
TSZ02201-0L2L0HZ00190-1-
2
© 2013 ROHM Co., Ltd. All rights reserved.
16.Jan.2013 Rev.001
www.rohm.co.jp
TSZ22111・15・001
●
●●
●Revision History
Date Revision Changes
16.Jan.2013
001 New Release
Datasheet
Datasheet
Notice-SS Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred b y you or thir d parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applicatio ns
JAPAN USA EU CHINA
CLASSⅢ CLASSⅢ CLASSⅡb CLASSⅢ
CLASSⅣ CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe d esign against the physical injur y, damage to any property, which
a failure or malfunction of our Products may cause. T he following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expens es or losses arising from the
use of any ROHM’s Products under an y special or extraordinary envir onments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product perform ance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-produci ng comp onents, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flu x (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation- proof design.
5. Please verify and confirm char acteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding nor mal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending o n Ambient temper ature (Ta). When us ed in se aled area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specificati on.
9. ROHM shall not be in any way responsible or liable for failure in duced under deviant condition from what is defined i n
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlor ine, bromine, etc.) flux is used, the residue of flux ma y negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM represe ntative in advance.
For details, please refer to ROHM Mounting specificati on
Datasheet
Datasheet
Notice-SS Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own indepe ndent verificati on and judgme nt in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, e xpenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please t ake special care under dry con dition (e.g. Grounding of human body / equipment / sol der iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportati on
1. Product performance and soldered conn ections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds thos e recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommen de d storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a hum idity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products pl ease dispose them properly using an authorized industry waste compan y.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoi ng information or data will not infringe any int ellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including b ut not limited to, the developm ent of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
DatasheetDatasheet
Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or
concerning such information.
