DG406, DG407 Vishay Siliconix 16-Ch/Dual 8-Ch High-Performance CMOS Analog Multiplexers DESCRIPTION FEATURES The DG406 is a 16 channel single-ended analog multiplexer designed to connect one of sixteen inputs to a common output as determined by a 4-bit binary address. The DG407 selects one of eight differential inputs to a common differential output. Break-before-make switching action protects against momentary shorting of inputs. An on channel conducts current equally well in both directions. In the off state each channel blocks voltages up to the power supply rails. An enable (EN) function allows the user to reset the multiplexer/demultiplexer to all switches off for stacking several devices. All control inputs, address (Ax) and enable (EN) are TTL compatible over the full specified operating temperature range. Applications for the DG406, DG407 include high speed data acquisition, audio signal switching and routing, ATE systems, and avionics. High performance and low power dissipation make them ideal for battery operated and remote instrumentation applications. Designed in the 44 V silicon-gate CMOS process, the absolute maximum voltage rating is extended to 44 V, allowing operation with 20 V supplies. Additionally single (12 V) supply operation is allowed. An epitaxial layer prevents latchup. For applications information please request documents 70601 and 70604. * * * * * Low on-resistance - RDS(on): 50 Low charge injection - Q: 15 pC Fast transition time - tTRANS: 200 ns Low power: 0.2 mW Single supply capability * 44 V supply max. rating Pb-free Available RoHS* COMPLIANT BENEFITS * * * * * * Higher accuracy Reduced glitching Improved data throughput Reduced power consumption Increased ruggedness Wide supply ranges: 5 V to 20 V APPLICATIONS * * * * * * * Data acquisition systems Audio signal routing Medical instrumentation ATE systems Battery powered systems High-rel systems Single supply systems FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION DG406 DG407 Dual-In-Line and SOIC Wide-Body V+ 28 1 Dual-In-Line and SOIC Wide-Body D V+ 1 28 Da Db 2 27 V- NC 2 27 V- NC 3 26 S8 NC 3 26 S8a S8b 4 25 S7a S16 4 25 S7 S15 5 24 S6 S7b 5 24 S6a S6b 6 23 S5a S14 6 23 S5 S13 7 22 S4 S5b 7 22 S4a S4b 8 21 S3a 20 S2a S12 8 21 S3 S11 9 20 S2 S3b 9 S2b 10 19 S1a 18 EN 17 A0 2 S10 10 19 S1 S9 11 18 EN S1b 11 17 A0 GND 12 16 A1 NC 13 16 A1 15 A2 NC 14 15 A2 GND 12 NC 13 A3 Decoders/Drivers 14 Top View Decoders/Drivers Top View * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 www.vishay.com 1 DG406, DG407 Vishay Siliconix FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION 5 25 S7 S7b S14 6 24 S6 S13 7 23 S5 S12 8 22 S11 9 21 S10 10 S9 11 Da V- S15 V+ D 28 27 26 Db V+ 1 NC NC 2 S 8b NC 3 S8 S 16 4 S 8a PLCC and LCC DG407 4 3 2 1 28 27 26 V- PLCC and LCC DG406 5 25 S7a S6b 6 24 S6a S5b 7 23 S5a S4 S4b 8 22 S4a S3 S3b 9 21 S3a 20 S2 S2b 10 20 S2a 19 S1 S1b 11 19 S1a EN A0 A1 A2 NC NC GND EN A0 NC A1 12 13 14 15 16 17 18 A2 12 13 14 15 16 17 18 A3 Decoders/Drivers GND Decoders/Drivers Top View Top View TRUTH TABLE (DG406) TRUTH TABLE (DG407) A3 A2 A1 A0 EN On Switch A2 A1 A0 EN On Switch Pair X 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 X 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 None 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 X 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 None 1 2 3 4 5 6 7 8 ORDERING INFORMATION (DG406) Temp. Range - 40 C to 85 C www.vishay.com 2 Package Part Number 28-Pin Plastic DIP DG406DJ DG406DJ-E3 28-Pin PLCC DG406DN DG406DN-T1-E3 28-Pin Widebody SOIC DG406DW DG406DW-E3 Logic "0" = VAL 0.8 V Logic "1" = VAH 2.4 V X = Do not Care ORDERING INFORMATION (DG407) Temp. Range - 40 C to 85 C Package Part Number 28-Pin Plastic DIP DG407DJ DG407DJ-E3 28-Pin PLCC DG407DN DG407DN-T1-E3 28-Pin Widebody SOIC DG407DW DG407DW-E3 Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 DG406, DG407 Vishay Siliconix ABSOLUTE MAXIMUM RATINGS Parameter Voltages Referenced to VDigital Inputs a, V+ GND VS, VD Current (Any terminal) Peak Current, S or D (Pulsed at 1 ms, 10 % duty cycle max.) Storage Temperature Power Dissipation (Package)b Limit 44 25 (V-) - 2 to (V+) + 2 V or 20 mA, whichever occurs first 30 100 (AK, AZ Suffix) - 65 to 150 (DJ, DN Suffix) - 65 to 125 Unit V mA C 28-Pin Plastic DIPb 625 28-Pin CerDIPd 1.2 W 28-Pin Plastic PLCCc 450 mW LCC-28e 28-Pin Widebody SOIC 1.35 W 450 mW mW Notes: a. Signals on SX, DX or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads soldered or welded to PC board. c. Derate 6 mW/C above 75C. d. Derate 12 mW/C above 75C. e. Derate 13.5 mW/C above 75C . Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 www.vishay.com 3 DG406, DG407 Vishay Siliconix SPECIFICATIONSa Test Conditions Unless Otherwise Specified V+ = 15 V, V- = - 15 V VAL = 0.8 V, VAH = 2.4 Vf Temp.b RDS(on) VD = 10 V, IS = - 10 mA sequence each switch on Full Room Full RDS(on) VD = 10 V Room Parameter Analog Switch Symbol Analog Signal Rangee Drain-Source On-Resistance RDS(on) Matching Between Channelsg VANALOG Source Off Leakage Current Drain Off Leakage Current IS(off) ID(off) VEN = 0 V VD = 10 V VS = 10 V DG406 DG407 Drain On Leakage Current ID(on) VS = VD = 10 sequence each switch on DG406 DG407 A Suffix D Suffix - 55 C to 125 C - 40 C to 85 C Room Full Room Full Room Full Room Full Room Full Typ.c Min.d Max.d Min.d Max.d Unit - 15 15 100 125 - 15 15 100 125 V 50 5 0.01 0.04 0.04 0.04 0.04 % - 0.5 - 50 -1 - 200 -1 - 100 -1 - 200 -1 - 100 0.5 50 1 200 1 100 1 200 1 100 - 0.5 -5 -1 - 40 -1 - 20 -1 - 40 -1 - 20 0.5 5 1 40 1 20 1 40 1 20 nA Digital Control Logic High Input Voltage VINH Full Logic Low Input Voltage VINL Full 2.4 2.4 0.8 0.8 V Logic High Input Current IAH VA = 2.4 V, 15 V Full -1 1 -1 1 Logic Low Input Current IAL VEN = 0 V, 2.4 V, VA = 0 V Full -1 1 -1 1 Logic Input Capacitance Cin f = 1 MHz Room 7 Transition Time tTRANS see figure 2 200 Break-Before-Make Interval tOPEN see figure 4 Enable Turn-On Time tON(EN) Enable Turn-Off Time tOFF(EN) Room Full Room Full Room Full Room Full Room 15 pC Room - 69 dB A pF Dynamic Characteristics see figure 3 Charge Injection Off Isolation h Source Off Capacitance Drain Off Capacitance Drain On Capacitance Q OIRR CS(off) CD(off) CD(on) VS = 0 V, CL = 1 nF, RS = 0 VEN = 0 V, RL = 1 k f = 100 kHz VEN = 0 V, VS = 0 V, f = 1 MHz VEN = 0 V VD = 0 V f = 1 MHz 50 350 450 25 10 150 8 Room 130 DG407 Room 65 DG406 Room 140 DG407 Room 70 Room Full Room Full Room Full Room Full 13 25 10 200 400 150 300 70 Room 350 450 200 400 150 300 ns pF Power Supplies Positive Supply Current I+ Negative Supply Current I- Positive Supply Current I+ Negative Supply Current I- VEN = VA = 0 or 5 V VEN = 2.4 V, VA = 0 V www.vishay.com 4 - 0.01 30 75 -1 - 10 50 - 0.01 30 75 -1 - 10 500 900 - 20 - 20 500 700 A - 20 - 20 Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 DG406, DG407 Vishay Siliconix SPECIFICATIONSa (for Single Supply) Parameter Analog Switch Symbol Analog Signal Rangee Drain-Source On-Resistance RDS(on) Matching Between Channelsg Source Off Leakage Current VANALOG Drain Off Leakage Current Drain On Leakage Current RDS(on) RDS(on) IS(off) ID(off) ID(on) Test Conditions Unless Otherwise Specified V+ = 12 V, V- = 0 V VAL = 0.8 V, VAH = 2.4 Vf A Suffix D Suffix - 55 C to 125 C - 40 C to 85 C Temp.b Typ.c Full VD = 3 V, 10 V, IS = - 1 mA sequence each switch on VEN = 0 V VD = 10 V or 0.5 V VS = 0.5 V or 10 V DG406 Room 90 Room 5 Room 0.01 Room 0.04 Min.d Max.d Min.d Max.d Unit 0 12 0 12 V 120 120 % DG407 Room 0.04 DG406 Room 0.04 DG407 Room 0.04 VS1 = 8 V, VS8 = 0 V, VIN = 2.4 V Room 300 450 Room 250 600 600 300 300 VS = VD = 10 sequence each switch on nA Dynamic Characteristics Switching Time of Multiplexer tOPEN Enable Turn-On Time tON(EN) Enable Turn-Off Time tOFF(EN) VINH = 2.4 V, VINL = 0 V VS1 = 5 V Room 150 Q CL = 1 nF, VS = 6 V, RS = 0 Room 20 13 VEN = 0 V or 5 V, VA = 0 V or 5 V Room Full Room Full Charge Injection 450 ns pC Power Supplies Positive Supply Current I+ Negative Supply Current I- - 0.01 30 75 - 20 - 20 30 75 - 20 - 20 A Notes: a. Refer to PROCESS OPTION FLOWCHART. b. Room = 25 C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. g. RDS(on) = RDS(on) max. - RDS(on) min. h. Worst case isolation occurs on Channel 4 due to proximity to the drain pin. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 www.vishay.com 5 DG406, DG407 Vishay Siliconix TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise noted) 160 80 RDS(on) - On-Resistance () RDS(on) - On-Resistance () 70 120 5V 80 8V 10 V 12 V 15 V 40 125 C 60 85 C 50 25 C 40 0 C 30 - 40 C 20 - 55 C 20 V 10 0 - 20 - 12 -4 4 VD - Drain Voltage (V) 12 V+ = 15 V V- = - 15 V 0 - 15 20 - 10 -5 0 5 10 15 VD - Drain Voltage (V) RDS(on) vs. VD and Temperature RDS(on) vs. VD and Supply 120 V+ = 7.5 V 80 200 I D , I S - Current (pA) RDS(on) - On-Resistance () V+ = 15 V V- = - 15 V VS = - VD for ID(off) VD = V S(open) for ID(on) V- = 0 V 240 160 10 V 120 12 V 15 V 80 20 V 40 IS(off) 0 DG406 ID(on), ID(off) - 40 22 V DG407 ID(on), ID(off) - 80 40 - 120 - 15 0 0 4 8 12 16 20 0 5 10 15 350 100 nA V+ = 15 V V- = - 15 V VD = "14 V 300 tTRANS 250 1 nA ID(on), ID(off) Time (ns) I D , I S - Current -5 ID , IS Leakage Currents vs. Analog Voltage RDS(on) vs. VD and Supply 10 nA - 10 VS , V D - Source Drain Voltage (V) VD - Drain Voltage (V) 100 pA 200 tON(EN) 150 IS(off) 10 pA 100 tOFF(EN) 1 pA 50 0.1 pA - 55 - 35 - 15 www.vishay.com 6 0 5 25 45 65 85 105 125 5 10 15 Temperature (C) VSUPPLY - Supply Voltage (V) ID , IS Leakages vs. Temperature Switching Times vs. Bipolar Supplies 20 Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 DG406, DG407 Vishay Siliconix TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise noted) 70 700 600 60 500 50 tTRANS 400 Q (pC) Time (ns) V- = 0 V 300 40 V+ = 12 V, V- = 0 V 30 tON(EN) 200 V+ = 15 V, V- = - 15 V 20 100 10 tOFF(EN) 0 5 10 15 0 - 15 20 - 10 -5 V+ - Supply Voltage (V) 0 5 10 VS - Source Voltage (V) Switching Times vs. Single Supply Charge Injection vs. Analog Voltage - 140 10 EN = 5 V AX = 0 or 5 V 8 - 120 I+ 6 - 100 4 I - Current (mA) ISOL (dB) 15 - 80 - 60 2 0 -2 IGND -4 - 40 I-6 - 20 -8 0 - 10 100 1K 10K 100K 1M 10M 10 100 1K f - Frequency (Hz) Off-Isolation vs. Frequency 1M 10M 3 V+ = 15 V V- = - 15 V 220 2 tTRANS V TH (V) Time (ns) 100K Supply Currents vs. Switching Frequency 300 260 10K f - Frequency (Hz) tON(EN) 180 140 1 100 tOFF(EN) 0 60 - 55 - 35 - 15 5 25 45 65 85 105 125 0 5 10 15 Temperature (C) VSUPPLY - Supply Voltage (V) tON/tOFF vs. Temperature Switching Threshold vs. Supply Voltage Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 20 www.vishay.com 7 DG406, DG407 Vishay Siliconix SCHEMATIC DIAGRAM (Typical Channel) V+ VREF GND D A0 V+ Level Shift AX V- Decode/ Drive S1 V+ EN Sn V- Figure 1. TEST CIRCUITS + 15 V + 2.4 V V+ EN A2 A1 10 V S1 A3 S2 - S 15 DG406 S16 A0 10 V VO D GND Logic Input V- tr < 20 ns tf < 20 ns 3V 50 % 0V 50 35 pF 300 - 15 V VS1 90 % Switch Output + 15 V + 2.4 V V+ EN A2 VO S1b 0V 90 % 10 V VS8 * DG407 S8b A1 A0 tTRANS 10 V S1 ON Db GND tTRANS S8 ON VO V- 50 300 35 pF - 15 V * = S1a - S 8a, S2b S 7b, Da Figure 2. Transition Time www.vishay.com 8 Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 DG406, DG407 Vishay Siliconix TEST CIRCUITS + 15 V V+ A3 -5V S1 A2 S2 - S 16 A1 DG406 A0 VO D EN GND V35 pF 300 50 Logic Input - 15 V tr < 20 ns tf < 20 ns 3V 50 % 0V tON(EN) 0V + 15 V V+ A2 S1b S1a - S 8a S2b - S 8b A1 A0 tOFF(EN) Switch Output -5V VO 90 % 90 % VO DG407 Da and Db EN GND VO V- 35 pF 50 300 - 15 V Figure 3. Enable Switching Time + 15 V Logic Input V+ EN + 2.4 V All S and Da A3 A2 A1 +5V tr < 20 ns tf < 20 ns 3V 50 % 0V DG406 DG407 A0 GND 50 VS VO D,D b 80 % Switch Output V300 35 pF VO - 15 V 0V tOPEN Figure 4. Break-Before-Make Interval Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 www.vishay.com 9 DG406, DG407 Vishay Siliconix APPLICATIONS HINTS Sampling speed is limited by two consecutive events: the transition time of the multiplexer, and the settling time of the sampled signal at the output. For the DG406 then, at room temp and for 12-bit accuracy, using the maximum limits: tTRANS is given on the data sheet. Settling time at the load depends on several parameters: RDS(on) of the multiplexer, source impedance, multiplexer and load capacitances, charge injection of the multiplexer and accuracy desired. fs = The settling time for the multiplexer alone can be derived from the model shown in figure 5. Assuming a low impedance signal source like that presented by an op amp or a buffer amplifier, the settling time of the RC network for a given accuracy is equal to n: % ACCURACY # BITS N 0.25 8 6 0.012 12 9 0.0017 15 11 (2) (3) From the sampling theorem, to properly recover the original signal, the sampling frequency should be more than twice the maximum component frequency of the original signal. This assumes perfect bandlimiting. In a real application sampling at three to four times the filter cutoff frequency is a good practice. fc = 1 x fs = 173 kHz 4 (4) From this we can see that the DG406 can be used to sample 16 different signals whose maximum component frequency can be as high as 173 kHz. If for example, two channels are used to double sample the same incoming signal then its cutoff frequency can be doubled. VOUT RS = 0 CD(on) Figure 5. Simplified Model of One Multiplexer Channel The maximum sampling frequency of the multiplexer is: 1 N(tSETTLING + tTRANS) (1) where N = number of channels to scan tSETTLING = n = n x RDS(on) x CD(on) To Sensor 1 To Sensor 8 or fs = 694 kHz Therefore from equation 2 above: R DS(on) fs = 1 16 (9 x 100 x 10-12F) + 300 x 10-12s Analog Multiplexer The block diagram shown in Figure 6 illustrates a typical data acquisition front end suitable for low-level analog signals. Differential multiplexing of small signals is preferred since this method helps to reject any common mode noise. This is especially important when the sensors are located at a distance and it may eliminate the need for individual amplifiers. A low RDS(on), low leakage multiplexer like the DG407 helps to reduce measurement errors. The low power dissipation of the DG407 minimizes on-chip thermal gradients which can cause errors due to temperature mismatch along the parasitic thermocouple paths. Please refer to Application Note AN203 for additional information. Inst Amp DG407 S/H 12-Bit A/D Converter Controller Figure 6. Measuring low-level analog signals is more accurate when using a differential multiplexing technique Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?70061. www.vishay.com 10 Document Number: 70061 S11-0179-Rev. J, 07-Feb-11 Package Information Vishay Siliconix PDIP: 28LEAD 28 27 26 25 24 23 22 21 20 19 18 17 16 15 E1 1 2 3 4 5 6 7 8 9 10 11 12 13 E 14 D Q1 S A(1) A L A1 L 15 MAX. C e1 B1 Dim A A1 B B1 C D E E1 e1 eA L Q1 S eA B MILLIMETERS Min Max INCHES Min Max 2.29 5.08 0.090 0.200 0.39 1.77 0.015 0.070 0.38 0.56 0.015 0.022 0.89 1.65 0.035 0.065 0.204 0.30 0.008 0.012 35.10 39.70 1.380 1.565 15.24 15.88 0.600 0.625 13.21 14.73 0.520 0.580 2.29 2.79 0.090 0.110 14.99 15.49 0.590 0.610 2.60 5.08 0.100 0.200 0.95 2.345 0.0375 0.0925 0.995 2.665 0.0375 0.105 ECN: S-03946--Rev. F, 09-Jul-01 DWG: 5488 Document Number: 71243 06-Jul-01 www.vishay.com 1 Package Information Vishay Siliconix PLCC: 28-LEAD D-SQUARE MILLIMETERS MIN. MAX. A 4.20 4.57 2.29 3.04 A1 0.51 A2 B 0.331 0.553 0.661 0.812 B1 D 12.32 12.57 11.430 11.582 D1 9.91 10.92 D2 1.27 BSC e1 ECN: T09-0766-Rev. D, 28-Sep-09 DWG: 5491 DIM. A2 INCHES MIN. MAX. 0.165 0.180 0.090 0.120 0.020 0.013 0.021 0.026 0.032 0.485 0.495 0.450 0.456 0.390 0.430 0.050 BSC e1 B1 D2 B D1-SQUARE A1 D A Document Number: 71264 28-Sep-09 0.101 mm 0.004" www.vishay.com 1 Package Information www.vishay.com Vishay Siliconix SOIC (WIDE-BODY): 28-LEADS 0.06 0.002D CAVITY NO. 0.3525 0.001 0.334 0.005 28 27 26 25 24 23 22 21 20 19 18 R0.004 17 16 15 0.010 0.1475 0.001 R0.008 0.295 0.001 R0.009 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 R0.004 2 0.032 0.005 0.070 0.005 0.055 0.005 DETAIL A PIN 1 INDICATOR 0.047 0.007 0.001 dp SURFACE POLISHED 0.334 0.005 0.291 0.001 0.091 0.001 0.020 45 0.705 0.001 0.098 0.002 R0.004 0.00825 0.00325 0.041 0.001 0.050 TYP. 0.017 0.0003 7(4 ) 0.295 0.001 0.406 0.004 DETAIL A All Dimensions In Inches ECN: E11-2209-Rev. D, 01-Aug-11 DWG: 5850 Revision: 01-Aug-11 1 Document Number: 71268 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information Vishay Siliconix 28LEAD LCC A1 D L1 A 28 e 1 2 L Document Number: 71278 02-Jul-01 E Dim A A1 B D E e L L1 MILLIMETERS Min Max INCHES Min Max 1.37 2.24 0.054 0.088 1.63 2.54 0.064 0.100 0.56 0.71 0.022 0.028 11.23 11.63 0.442 0.458 11.23 11.63 0.442 0.458 1.27 BSC 0.050 BSC 1.14 1.40 0.045 0.055 1.96 2.36 0.077 0.093 ECN: S-03946--Rev. B, 09-Jul-01 DWG: 5319 B www.vishay.com 1 Package Information Vishay Siliconix CERDIP: 28LEAD 28 E1 E 1 2 3 D Q1 S A L1 A1 B1 L e1 C B eA MILLIMETERS Dim A A1 B B1 C D E E1 e1 eA L L1 Q1 S INCHES Min Max Min Max 4.06 5.92 0.160 0.232 0.38 1.52 0.015 0.060 0.38 0.51 0.015 0.020 1.14 1.65 0.045 0.065 0.20 0.30 0.008 0.012 36.58 37.08 1.440 1.460 15.24 15.88 0.600 0.625 12.95 13.46 0.510 0.530 2.54 BSC 0.100 BSC 15.24 BSC 0.600 BSC 3.18 3.81 0.125 0.150 3.81 5.08 0.150 0.200 1.27 2.16 0.050 0.085 1.52 2.29 0.060 0.090 0 15 0 15 ECN: S-03946--Rev. E, 09-Jul-01 DWG: 5434 Document Number: 71283 03-Jul-01 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000