• Case : Pa6T
• Actuator : polyamide, glass filled
• Bushing : brass, nickel plated
• Contacts : CD : brass, gold plated
• Terminal seal : epoxy
APEM products may be recycled at end-of-life for the re-claiming of valuable metal components.
MATERIALS
9533-9233 9532-9232 9533N
9233N-9133
Total travel 1.10 (.043) 1.80 (.070) 1 (.039)
Pre-travel 0.80 (.031) 1.00 (.039) -
Over travel 0.30 (.011) 0.75 (.029) -
• Torque : 0.5 Nm (.590 Ft.lb) max. applied to nut
• Operating temperature : -30 °C to +65 °C (-22 °F to +146 °F)
• Panel thickness : 1.50 mm (.059) max.
• Travels : see table below . Tolerance : ± 0.3 mm (.011)
GENERAL SPECIFICATIONS
• Max. current/voltage rating with resistive load : 100 mA 30 VDC
• Initial contact resistance : 30 mΩ max.
• Insulation resistance : 1,000 MΩ min. at 500 VDC
• Dielectric strength :
500 Vrms 50 Hz min. between terminals
1,000 Vrms 50 Hz min. between terminals and frame
• Electrical life at full load :
9100 - 9200N and 9500N : 250,000 cycles
9200 - 9500 : 100,000 cycles
ELECTRICAL SPECIFICATIONS
Panel and PC mount models, horizontal or vertical
Self-cleaning and butt action contacts
Several plunger options
DISTINCTIVE FEATURES
Subminiature momentary pushbutton switches
9100-9200-9500
series
The company reserves the right to change specifications without notice.
PANEL SWITCHES
1
SW-9100-9200-9500-1801
Subminiature momentary pushbutton switches
9100-9200-9500 series
TERMINALS
(.078)
(.039)
(.039)
(.031)
1.00
2.00
0.80
1.00
(.118)
3.00
(.157)
(.023)
4.00
0.60
(.196)
5.00
Function 2 (NC) Function 3 (NO)
ELECTRICAL FUNCTIONS
(.165 DIA)
Ø4.20
PANEL CUT-OUT
(.196) (.059)
(.157 DIA X 0.70 IS)
M4 X 0.70 SI
5.00 1.50
U544 (nickel plated)
STANDARD HARDWARE
(FOR THREADED BUSHING MODELS)
PANEL SWITCHES
2
BUILD YOUR PART NUMBER
9100-9200-9500 series
Subminiature momentary pushbutton switches
SERIES
9
BASIC PART NUMBER
3Single pole
NUMBER OF POLES
2Normally closed (NC)
3Normally open (NO)
ELECTRICAL FUNCTIONS
Case height 8 (.314)
2Straight terminals - threaded bushing
2..Y Tall bracket - plain bushing
2..WW Right angle terminals - plain bushing
5Solder lugs - threaded bushing
Case height 6.1 (.240)
1Straight terminals - threaded bushing -
7.10 (.279) PCB to panel
1..Y Short bracket - plain bushing
1..WW Right angle terminals - plain bushing
2..N Straight terminals - threaded bushing -
8.90 (.350) PCB to panel
2..NY Tall bracket - plain bushing
5..N Solder lugs - threaded bushing
TERMINALS, CASE AND BUSHING
ABOUT THIS SERIES
Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information.
Sealing boots are available to protect the switches. See "Sealing Boots" section of website.
Mounting accessories : standard hardware supplied with all threaded bushing models : 1 nickel plated hex nut 5 (.196)
across flats, part number U544. This nut is presented on previous page.
OPTIONS
CD Gold plated brass
(standard)
CONTACT MATERIALS
Blank Epoxy sealed
terminals standard
KFront panel sealing
by two O-rings
SEALING
For plunger -4
U4310 Height 4 (.157)
U4320 Height 3.9 (.153)
CAPS
PLUNGER
Blank Standard
-0 Flush
-4 Long
MOUNTING BEZEL
U4922 For 9500 model
only.
On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart.
STANDARD HARDWARE
(FOR THREADED BUSHING MODELS)
PANEL SWITCHES
3
9100-9200-9500 series
Subminiature momentary pushbutton switches
8.00
3.00
3.50
Ø4.00 X 0.70 SI
Ø6.50
Ø2.45
EPOXY
(.157 DIA X 0.70 IS)
(.255 DIA)
(.314)
(.118)
(.137)
(.096 DIA)
(.100)
(.196)
(.023)
5.00
2.54
0.60
(.008)
0.20
(.100)
2.54
(.043 DIA)
Ø1.10
LONG CASE - STRAIGHT PC TERMINALS : 9200
LONG CASE - STRAIGHT PC TERMINALS
BRACKET MOUNTING : 9200Y
LONG CASE - SOLDER LUGS : 9500
(.096 DIA)
(.137)
(.118)
(.314)
(.100)
(.255 DIA)
(.078)
(.118)
(.157 DIA X 0.70 IS)
EPOXY
Ø2.45
2.54
2.00
Ø6.50
Ø4.00 X 0.70 SI
3.50
3.00
8.00
3.00
(.008)
0.20
LONG CASE - RIGHT ANGLE TERMINALS :
9200WW
Normally Closed
Normally Open
9532
9533
Normally Closed
9232
Normally Open9233
Normally Closed
9232Y
Normally Open9233Y
Normally Closed
9232WW
Normally Open9233WW
(.096 DIA)
(.137)
(.102)
(.366)
(.157)
(.023)
(.200)
(.100)
(.300)
(.200)
(.300)
(.100)
5.08
0.60
Ø2.45
2.54
7.62
5.08
7.62
2.54
4.00
9.30
3.50
2.60
Ø1.10
(.043 DIA)
(.118 DIA)
Ø3.00
EPOXY
(.015)
0.40
(.008)
0.20
(.096 DIA)
(.023)
(.118)
(.400)
(.374)
(.200)
(.008)
(.023)
(.200)
(.255)
(.200)
(.400)
(.100)
2.54
10.16
5.08
0.60
Ø6.5
0.20
0.60
10.16
5.08
9.50
5.08
Ø2.45
3.00
EPOXY
(.118 DIA)
Ø3.00
(.137) (.106)
(.100)
3.50 2.70
2.54
(.127)
3.25
(.023)
0.60
(.043 DIA)
Ø1.10
PANEL SWITCHES
4
9100-9200-9500 series
Subminiature momentary pushbutton switches
SHORT CASE - STRAIGHT PC TERMINALS
8.90 (.350) PCB TO PANEL
SHORT CASE - STRAIGHT PC TERMINALS
7.10 (.279) PCB TO PANEL
0.60
2.54
(.023)
(.100)
(.096 DIA) (.157 DIA X 0.70 IS)
EPOXY
Ø2.45 Ø4.00 X 0.70 SI
(.240)
6.10
(.008)
0.20
3.00
3.25
(.118)
(.127)
(.255 DIA)
Ø6.50
(.279)(.157)
(.100)
2.54
(.043 DIA)
Ø1.10
4.00 7.10
SHORT CASE - STRAIGHT PC TERMINALS
TALL BRACKET : 9200NY
Normally Open9233NY
Normally Open9133
SHORT CASE - SOLDER LUGS : 9500N
3.00
Ø4.00 X 0.70 SI
2.00
2.54
Ø2.45
EPOXY
(.157 DIA X 0.70 IS)
(.118)
(.078)
(.100)
(.096 DIA)
(.240)
6.10
(.015)
0.40
3.00
3.50
(.118)
(.137)
Ø6.50
(.255 DIA)
Normally Open
9533N
Normally Open9233N
0.60
2.54
(.023)
(.100)
(.096 DIA)
(.137)
(.118)
(.255 DIA)
(.157 DIA X 0.70 IS)
EPOXY
Ø2.45
Ø6.50
Ø4.00 X 0.70 SI
3.50
3.00
(.015)
0.40
(.350)(.157)
6.10
(.240)
Ø1.10
(.043 DIA)
2.54
(.100)
4.00 8.90
EPOXY
Ø3.00
(.118 DIA)
(.043 DIA)
Ø1.10
2.60
3.50
4.00
2.54
7.62
5.08
7.62
2.54
Ø2.45
0.60
5.08
(.100)
(.300)
(.200)
(.300)
(.100)
(.200)
(.023)
(.157)
(.102)
(.137)
(.096 DIA)
(.366)
9.30
(.015)
(.015)
(.023)
0.40
0.40
0.60
PANEL SWITCHES
5
SHORT CASE - STRAIGHT PC TERMINALS
SHORT BRACKET : 9100Y
Normally Open9133Y
9100-9200-9500 series
Subminiature momentary pushbutton switches
SHORT CASE - RIGHT ANGLE TERMINALS -
VERTICAL : 9100WW
Normally Open9133WW
Ø3.00
(.118 DIA)
EPOXY
3.00
5.08
7.60
5.08
Ø6.5
0.60
5.08
10.16
2.54
(.100)
(.400)
(.255)
(.200)
(.023)
(.200)
(.299)
(.118)
(.096 DIA)
(.015)
0.40
(.106)
(.137)
3.50
(.400) (.100)
10.16 2.54
(.023)
(.023)
0.60
0.60
2.70
Ø1.10
(.043 DIA)
(.127)
3.25
EPOXY
Ø3.00
(.118 DIA)
(.043 DIA)
Ø1.10
2.60
3.50
4.00
2.54
7.62
5.08
7.62
2.54
Ø2.45
0.60
5.08
(.100)
(.300)
(.200)
(.300)
(.100)
(.200)
(.023)
(.157)
(.102)
(.137)
(.096 DIA)
(.303)
7.70
(.023)
(.015)
(.008)
0.40
0.20
0.60
CD Gold plated brass (standard)
CONTACT MATERIALS
BASIC P/N
Blank Epoxy sealed terminals standard
K Front panel sealing by two O-rings. Protects
the switch against water and dust. Panel seal
withstands 0.1 bar pressure.
Option K for models 9533N, 9233N and 9133
only.
SEALING
BASIC P/N
1
O-ring
PANEL SWITCHES
6
4.00
(.157)
Ø6.50
3.00
(.118)
(.255)
9100-9200-9500 series
Subminiature momentary pushbutton switches
Blank
Standard
with long case
-0
Flush
Blank
Standard
with short case
PLUNGERS
BASIC P/N
(.096 DIA)
Ø2.45
(.137)
3.50
C95NP13-A
3.20
(.126)
Ø2.45
(.096 DIA)
8.00
(.314)
(.240)
6.10
4.70
(.185)
Ø2.45
(.096 DIA) (.096 DIA)
Ø2.45
(.169)
4.30
C95NP4-A
(.314)
8.00
6.10
(.240)
(.098 DIA)
Ø2.5
-4
Long
with long case
-4
Long
with short case
CAPS
+ U...
BASIC P/N
U4310 For use with plunger -4 only
U4320 For use with plunger -4 only
For cap colors, replace "0" with number :
1 Blue
1/4 Dark blue
2 Black
3 Green
4 Grey
5 Yellow
6 Red
7 Ivory
7/1 White
9 Orange
U4310
(.118)
3.00
(.153)
Ø5.00
3.90
(.196 DIA)
U4320
For 9500 model (case height 8 mm) only
MOUTING BEZEL
BASIC P/N + U...
(.433)
ø11.00
(.035)
0.90
(.090)
2.30
15.60
(.614)
U4922
The mounting bezel U4922 has been designed to facilitate the mounting of the 9500 series pushbutton switch onto
a panel. The switch + bezel assembly is snapped into the equipment through the front of the panel, then electrically
connected by solder lug terminals.
Panel cut-out : Ø 8.15 mm ± 0.05 (.320 DIA ± .002)
If not combined with bezel U4922, caps are to be ordered
separately.
PANEL SWITCHES
7