BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Features: 1. Emitted Color: Super Yellow Green. Package Dimensions: 2. Lend Appearance: Water Clear. 3. Wide range of collector current. 4. Low cost plastic package 5. This product doesn't contain restriction Substance, comply ROHS standard. Applications: 1. Automotive: Dashboards, stop lamps, turn signals. 2. Backlighting: LCDs, Key pads advertising. 3. Status indicators: Comsumer & industrial electronics. 4. General use. NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.10mm (0.004") unless otherwise specified. 3. Specifications are subject to change without notice. Absolute Maximum Ratings(Ta=25) Parameter Rating Unit Power Dissipation 100 mW Collector-Emitter Voltage (Max.) 30 V Emitter-Collector Voltage(Min.) 100 V Operating Temperature Range -25~80 - Storage Temperature Range -30~85 - Soldering Temperature See Page 4 - http://www.brtled.com Ver.2.0 Page 1 of 6 BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Electrical and optical characteristics(Ta=25) Parameter Symbol Condition Min. Typ. Max. Unit Forward Voltage Vf IF=20mA - 2.0 2.6 V Luminous Intensity Iv IF=20mA 42 100 - mcd Reverse Current IR VR=5V - - 100 A 570 - nm 576 nm Peak Wave Length p IF=20mA - Dominant Wave Length d IF=20mA 566 Spectral Line Half-width IF=20mA - 30 - nm Veiwing Angle 21/2 IF=20mA - 35 - deg Typical Electro-Optical Characteristics Curves Fig.2 Forward current derating curve Fig.1 Relative intensity vs. wavelength vs. ambient temperature 1.0 60 Forward current (mA) Relative radiant intensity 50 0.5 0 520 570 40 30 20 10 0 620 20 Wavelength (nm) 80 100 3.0 50 2.5 Relative Luminous intensity (Normalized @20mA) 40 Forward current (mA) 60 Fig.4 Relative luminous intensity vs. ambient temperature Fig.3 Forward current vs. forward voltage 30 20 10 0 40 Ambient temperature Ta( C) 1 2 3 4 2.0 1.5 1.0 0.5 0 -40 5 -20 0 40 20 60 Ambient A temperature Ta( C) Forward voltage(V) http://www.brtled.com Fig.5 Relative luminous intensity vs. forward current Fig.6 Radiation diagram 0 10 20 30 1.5 Relative radiant intensity Relative luminous intensity (@20mA) 2.0 1.0 0.5 1.0 40 0.9 50 0.8 60 70 0.7 0 10 20 30 40 Forward current (mA) 80 90 50 0.5 0.3 0.1 0.2 0.4 0.6 Ver.2.0 Page 2 of 6 BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Tapping and packaging specifications(Units: mm) SPECIFICATION ITEM SYMBOL Minimum Maximum mm inch mm inch Tape Feed Hole Diameter (DIA) D0 1.40 0.055 1.55 0.061 Feed Hole Location E 1.65 0.065 1.85 0.072 Centers Line Dimensions Length Direction F 5.45 0.215 5.55 0.218 Compartment Depth K0 3.00 0.118 3.20 0.126 Carrier Tape Overall Thickness K 3.00 0.118 3.20 0.126 Compartment Pitch P 3.90 0.153 4.10 0.161 Sprocket Hole Diameter P0 3.90 0.153 4.10 0.161 Centers Line Dimensions Length Direction P2 1.95 0.076 2.05 0.080 Carrier Tape Thickness t 0.30 0.012 Carrier Tape Width W 12.00 0.472 12.30 0.484 Flange Diameter A 178.0 7.008 180.0 7.087 Hub Spindle Hole C 12.50 0.492 13.50 0.531 Hub Diameter D2 20.00 0.788 21.50 0.846 Fixing Tape Width W1 9.00 0.354 9.30 0.366 Flange Space Between Flanges T 16.00 0.629 17.00 0.669 Compartment Length A0 1.87 0.074 2.07 0.081 Compartment Width B0 6.30 0.248 6.50 0.256 e d o n A e d o h t a C http://www.brtled.com Ver.2.0 Page 3 of 6 BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Reliability Test Classification Test Item Reference Standard Operation Life MIL-STD-750:1026 MIL-STD-883:1005 JIS C 7021 :B-1 High Temperature MIL-STD-202:103B High Humidity JIS C 7021 :B-11 Endurance Storage Test High MIL-STD-883:1008 Temperature JIS C 7021 :B-10 Storage Low Temperature JIS-C-7021 :B-12 Storage Temperature MIL-STD-202:107D Cycling MIL-STD-750:1051 MIL-STD-883:1010 JIS C 7021 :A-4 Thermal Shock MIL-STD-202:107D Environmental MIL-STD-750:1051 Test MIL-STD-883:1011 Solder MIL-STD-202:201A Resistance MIL-STD-750:2031 JIS C 7021 :A-1 Test Conditions Result Connect with a power VCE=5V Ta=Under room temperature Test time=1,000hrs Ta=+655 RH=90%-95% Test time=240hrs 0/20 0/20 High Ta=+855 Test time=1,000hrs 0/20 Low Ta=-355 Test time=1,000hrs 0/20 -35 ~ +25 ~ +85 ~ +25 60min 20min 60min 20min Test Time=5cycle -355 ~ +855 20min 20min Test Time=10cycle Preheating 140-160, within 2 minutes. Operation heating 260 (Max.), within 10seconds. (Max.) 0/20 0/20 0/20 Judgment criteria of failure for the reliability Measuring items Symbol Measuring conditions Judgment criteria for failure Collector Dark Current ICEO VCE=20V Over Ux2 http://www.brtled.com Collector Light Current Note: IC(ON) VCE= 5V, H=1.0 mW/cm2,p=940nm 1.U means the upper limit of specified characteristics. Below SX0.5 S means initial value. 2. Measurment shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test. Ver.2.0 Page 4 of 6 BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Soldering : 1. Manual of Soldering The temperature of the iron tip should not be higher than 300(572) and Soldering within 3 seconds per solder-land is to be observed. 2. Reflow Soldering Preheating : 140~1605,within 2 minutes. Operation heating : 260(Max.) within 10 seconds.(Max) Gradual Cooling (Avoid quenching). 10 SEC. MAX. Temperature 140~160 260 MAX. 4 /SEC. MAX. 4 /SEC. MAX. OVER 2 MIN. Time 3. DIP soldering (Wave Soldering) : Preheating : 120~150,within 120~180 sec. Operation heating : 2455 within 5 sec.260 (Max) Gradual Cooling (Avoid quenching). Temperature Soldering heat Max. 260 245 5 within 5 sec. 120~150 Preheat 120~180 sec. Time http://www.brtled.com Handling : Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to high temperature. Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such as the sand blast and the metal hook. Ver.2.0 Page 5 of 6 BRIGHT LED ELECTRONICS CORP. BL-XGE361-TR7 SINCE 1981 Notes for designing: Care must be taken to provide the current limiting resistor in the circuit so as to drive the BRIGHT LEDs within the rated figures. Also, caution should be taken not to overload BRIGHT LEDs with instantaneous voltage at the turning ON and OFF of the circuit. When using the pulse drive care must be taken to keep the average current within the rated figures. Also, the circuit should be designed so as be subjected to reverse voltage when turning off the BRIGHT LEDs. Storage: In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as possible after unpacking the sealed envelope. If the envelope is still packed, to store it in the environment as following: (1) Temperature : 5-30(41)Humidity : RH 60Max. (2) After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or equivalent soldering process must be: a. Completed within 168 hours. b. Stored at less than 30% RH. (3) Devices require baking before mounting, if: (2) a or (2) b is not met. (4) If baking is required, devices must be baked under below conditions: 48 hours at 603. Package and Label of Products: (1) Package: Products are packed in one bag of 1500 pcs (one taping reel) and a label is attached on each bag. (2) Label: BRIGHT LED LOGO BL-Hxxxxx-TRB Part No. Quantity BIN. Sealing Date http://www.brtled.com x xx xx Year Month xx Day Manufacture Location Ver.2.0 Page 6 of 6