[ /Title (CD74 HC435 1, CD74 HCT43 51, CD74 HC435 2) /Subject (High Speed CMOS Logic Analog Multiplexers/De multiplexers with Latch) /Autho r () /Keywords (High Speed CMOS Logic CD54/74HC4351, CD74HCT4351, CD74HC4352 Data sheet acquired from Harris Semiconductor SCHS213A September 1998 - Revised May 2000 High Speed CMOS Logic Analog Multiplexers/Demultiplexers with Latch Features LSTTL with the low power consumption of standard CMOS integrated circuits. * Wide Analog Input Voltage Range . . . . . . . . . 5V (Max) These analog multiplexers/demultiplexers are, in essence, the HC/HCT4015 and HC4052 preceded by address latches that are controlled by an active low Latch Enable input (LE). Two Enable inputs, one active low (E1), and the other active high (E2) are provided allowing enabling with either input voltage level. * Low "On" Resistance - VCC - VEE = 4.5V. . . . . . . . . . . . . . . . . . . . . . 70 (Typ) - VCC - VEE = 9V . . . . . . . . . . . . . . . . . . . . . . . 40 (Typ) * Low Crosstalk Between Switches * Fast Switching and Propagation Speeds Ordering Information * "Break-Before-Make" Switching * Wide Operating Temperature Range . . . -55oC to 125oC TEMP. RANGE (oC) PACKAGE CD54HC4351F3A -55 to 125 20 Ld CERDIP CD74HC4351E -55 to 125 20 Ld PDIP CD74HC4351M -55 to 125 20 Ld SOIC CD74HCT4351E -55 to 125 20 Ld PDIP CD74HC4352E -55 to 125 20 Ld PDIP PART NUMBER * HC Types - 2V to 6V Operation, Control; 0V to 10V Switch - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V * HCT Types - 4.5V to 5.5V Operation, Control; 0V to 10V Switch - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il 1A at VOL, VOH NOTES: 1. When ordering, use the entire part number. Add the suffix 96 to obtain the variant in the tape and reel. Description 2. Wafer and die for this part number is available which meets all electrical specifications. Please contact your local TI sales office or customer service for ordering information. The 'HC4351, CD74HCT4351, and CD74HC4352 are digitally controlled analog switches which utilize silicon-gate CMOS technology to achieve operating speeds similar to Pinouts CD54HC4351 (CERDIP) CD74HC4351, CD74HCT4351 (PDIP, SOIC) TOP VIEW A4 1 CD74HC4352 (PDIP) TOP VIEW 20 VCC A6 2 19 A2 NC 3 18 A1 A COMMON 4 17 A0 A7 5 16 A3 A5 6 15 S0 E1 7 14 NC E2 8 13 S1 VEE 9 12 S2 GND 10 11 LE B0 1 B2 2 19 A2 NC 3 18 A1 B COMMON 4 17 A COMMON B3 5 16 A0 B1 6 15 A3 E1 7 14 NC E2 8 13 S0 VEE 9 12 S1 GND 10 11 LE CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2000, Texas Instruments Incorporated 1 20 VCC CD54/74HC4351, CD74HCT4351, CD74HC4352 Functional Diagram 'HC4351, CD74HCT4351 CHANNEL IN/OUT VCC 20 A7 A6 A5 A4 A3 A2 A1 A0 5 2 6 1 16 19 18 17 TG S0 15 TG S1 13 S2 12 TG LATCHES TG BINARY TO 1 OF 8 DECODER WITH ENABLE LOGIC LEVEL CONVERSION LE 11 4 A COMMON OUT/IN TG TG E1 TG 7 TG E2 8 10 GND 9 VEE TRUTH TABLE 'HC4351, CD74HCT4351 INPUT STATES E1 E2 S2 S1 S0 (NOTE 3) "ON" SWITCHES LE = H L H L L L A0 H L L H A1 L H L H L A2 L H L H H A3 L H H L L A4 L H H L H A5 L H H H L A6 L H H H H A7 H L X X X None FROM SELECT LOGIC P P VCC VCC N N N N VEE FIGURE 1. DETAIL OF ONE HC/HCT4351 SWITCH NOTE: 3. When LE is low S0-S2 data are latched and switches cannot change state. H = High Voltage Level, L = Low Voltage Level, X = Don't Care 2 A COMMON IN/OUT L An IN/OUT CD54/74HC4351, CD74HCT4351, CD74HC4352 Functional Diagram CD74HC4352 A CHANNELS IN/OUT VCC A3 A2 A1 A0 15 19 18 16 20 TG S0 13 S0 S0 LATCHES S1 12 LE TG S1 TG S1 BINARY TO 1 OF 4 DECODER WITH ENABLE LOGIC LEVEL CONVERSION 11 TG 17 A COMMON OUT/IN TG 4 B COMMON OUT/IN TG E1 7 E2 8 TG TG 10 9 GND 5 2 6 1 B0 B1 B2 B3 B CHANNELS IN/OUT VEE TRUTH TABLE CD74HC4352 An (Bn) IN/OUT INPUT STATES E1 E2 S1 S0 FROM SELECT LOGIC (NOTE 4) "ON" SWITCHES LE = H H L L A0, B0 L H L H A1, B1 L H H L A2, B2 L H H H A3, B3 H L X X None VCC N N N N VEE NOTE: 4. When Latch Enable is "Low" channel-select data is latched and switches cannot change state. H = High Voltage Level, L = Low Voltage Level, X = Don't Care FIGURE 2. DETAIL OF ONE CD74HC4352 SWITCH 3 A COMMON (B COMMON) IN/OUT L P P VCC CD54/74HC4351, CD74HCT4351, CD74HC4352 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Supply Voltage, VCC - VEE . . . . . . . . . . . . . . . . . . -0.5V to 10.5V DC Supply Voltage, VEE . . . . . . . . . . . . . . . . . . . . . . . . 0.5V to -7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC 0.5V. . . . . . . . . . . . . . . . . . . . . . . .20mA DC Switch Diode Current, IOK For VI < VEE -0.5V or VI < VCC + 0.5V . . . . . . . . . . . . . . . . .25mA DC Switch Current, IOK (Note 5) For VI > VEE -0.5V or VI < VCC + 0.5V . . . . . . . . . . . . . . . . .20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .50mA Thermal Resistance (Typical, Note 6) JA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V Supply Voltage Range, VCC - VEE HC, HCT Types (Figure 3) . . . . . . . . . . . . . . . . . . . . . . .2V to 10V Supply Voltage Range, VEE HC, HCT Types (Figure 4) . . . . . . . . . . . . . . . . . . . . . . . 0V to -6V DC Input or Output Voltage, VI . . . . . . . . . . . . . . . . . . . GND to VCC Analog Switch I/O Voltage, VIS . . . . . . . . . . . . . . . . . . . . . VEE (Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC (Max) Input Rise and Fall Time, tr, tf 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 5. In certain applications, the external load-resistor current may include both VCC and signal-line components. To avoid drawing VCC current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0.6V (calculated from RON values shown in the DC Electrical Specifications table). No VCC current will flow through RL if the switch current flows into terminal 3 on the 'HC4351 and CD74HCT4351; terminals 3 and 13 on the CD74HC4352. 6. JA is measured with the component mounted on an evaluation PC board in free air. Recommended Operating Area as a Function of Supply Voltage 8 6 VCC - GND (V) 4 8 6 VCC - GND (V) 4 HCT HC 2 0 HCT HC 2 0 2 0 4 6 8 10 12 VCC - VEE (V) FIGURE 3. 0 -2 -4 -6 -8 VEE - GND (V) FIGURE 4. 4 CD54/74HC4351, CD74HCT4351, CD74HC4352 DC Electrical Specifications PARAMETER -40oC TO 85oC 25oC TEST CONDITIONS -55oC TO 125oC SYMBOL VI (V) VIS (V) VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS VIH - - - 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V 0 4.5 - 70 160 - 200 - 240 0 6 - 60 140 - 175 - 210 -4.5 4.5 - 40 120 - 150 - 180 0 4.5 - 90 180 - 225 - 270 0 6 - 80 160 - 200 - 240 -4.5 4.5 - 45 130 - 162 - 195 0 4.5 - 10 - - - - - 0 6 - 8.5 - - - - - -4.5 4.5 - 5 - - - - - 0 6 - - 0.1 - 1 - 1 A -5 5 - - 0.2 - 2 - 2 A 0 6 - - 0.2 - 2 - 2 A -5 5 - - 0.4 - 4 - 4 A HC TYPES High Level Input Voltage Low Level Input Voltage "ON" Resistance IO = 1mA Figure 9 VIL RON - VIH or VIL - VCC or VEE VCC to VEE Maximum "ON" Resistance Between Any Two Channels Switch On/Off Leakage Current 4 Channels (4352) RON IIZ - VIH or VIL Switch On/Off Leakage Current 8 Channels (4351) - For Switch OFF: When VIS = VCC VOS = VEE; When VIS = VEE, VOS = VCC For Switch ON: All Applicable Combinations of VIS and VOS Voltage Levels - Control Input Leakage Current IIL VCC or GND - 0 6 - - 0.1 - 1 - 1 A Quiescent Device Current IO = 0 ICC VCC or GND When VIS = VEE, VOS = VCC, When VIS = VCC, VOS = VEE 0 6 - - 8 - 80 - 160 A -5 5 - - 16 - 160 - 320 A 5 CD54/74HC4351, CD74HCT4351, CD74HC4352 DC Electrical Specifications (Continued) SYMBOL VI (V) VIS (V) VEE (V) VCC (V) High Level Input Voltage VIH - - - Low Level Input Voltage VIL - - "ON" Resistance IO = 1mA Figure 9 RON VIH or VIL VCC or VEE PARAMETER -40oC TO 85oC 25oC TEST CONDITIONS -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V 0 4.5 - 70 160 - 200 - 240 -4.5 4.5 - 40 120 - 150 - 180 0 4.5 - 90 180 - 225 - 270 -4.5 4.5 - 45 130 - 162 - 195 0 4.5 - 10 - - - - - -4.5 4.5 - 5 - - - - - 0 6 - - 0.1 - 1 - 1 A -5 5 - - 0.2 - 2 - 2 A 0 6 - - 0.2 - 2 - 2 A -5 5 - - 0.4 - 4 - 4 A 0 5.5 - - 0.1 - 1 - 1 A 0 5.5 - - 8 - 80 - 160 A -4.5 5.5 - - 16 - 160 - 320 A - 4.5 to 5.5 - 100 360 - 450 - 490 A HCT TYPES VCC to VEE Maximum "ON" Resistance Between Any Two Channels Switch On/Off Leakage Current 4 Channels (4352) RON IIZ - VIH or VIL Switch On/Off Leakage Current 8 Channels (4351) Control Input Leakage Current Quiescent Device Current IO = 0 Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC or GND ICC - For Switch OFF: When VIS = VCC VOS = VEE; When VIS = VEE, VOS = VCC For Switch ON: All Applicable Combinations of VIS and VOS Voltage Levels - Any When Voltage VIS = VEE, BeVOS = VCC, tween When VCC VIS = VCC, and VOS = VEE GND ICC VCC -2.1 - NOTE: For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table TYPE INPUT UNIT LOADS All E1, E2, Sn 0.5 (4351, 4352) LE 1.5 NOTE: Unit Load is ICC limit specified in DC Electrical Table, e.g., 360A max at 25oC. 6 CD54/74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns -40oC TO 85oC 25oC PARAMETER -55oC TO 125oC SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPLH, tPHL CL = 50pF 0 2 - - 35 - 45 - 55 ns 0 4.5 - - 7 - 9 - 11 ns 0 6 - - 6 - 8 - 9 ns -4.5 4.5 - - 5 - 7 - 8 ns 0 2 - - 300 - 375 - 450 ns 0 4.5 - - 60 - 75 - 90 ns 0 6 - - 51 - 64 - 77 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 27 - - - - - ns CL = 50pF 0 2 - - 350 - 440 - 525 ns 0 4.5 - - 70 - 88 - 105 ns 0 6 - - 60 - 75 - 90 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 2 - - 300 - 375 - 450 ns 0 4.5 - - 60 - 75 - 90 ns 0 6 - - 51 - 64 - 77 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 27 - - - - - ns CL = 50pF 0 2 - - 375 - 470 - 565 ns 0 4.5 - - 75 - 94 - 113 ns 0 6 - - 64 - 80 - 96 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 2 - - 250 - 315 - 375 ns 0 4.5 - - 50 - 63 - 75 ns 0 6 - - 43 - 54 - 64 ns -4.5 4.5 - - 40 - 50 - 60 ns - 5 - 21 - - - - - ns HC TYPES Propagation Delay, Switch In to Switch Out Maximum Switch Turn "ON" Delay 4351 E1, E2, LE to VOS Maximum Switch Turn "ON" Delay 4352 E1, E2, LE to VOS Maximum Switch Turn "ON" Delay 4351 Sn to VOS Maximum Switch Turn "ON" Delay 4352 Sn to VOS Maximum Switch Turn "OFF" Delay 4351 E1 to VOS tPZH, tPZL tPZH, tPZL tPZH, tPZL tPZH, tPZL tPHZ, tPLZ CL = 50pF CL = 15pF 7 CD54/74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns (Continued) -40oC TO 85oC 25oC PARAMETER Maximum Switch Turn "OFF" Delay 4351 E2 to VOS Maximum Switch Turn "OFF" Delay 4351 LE to VOS Maximum Switch Turn "OFF" Delay 4351 Sn to VOS Maximum Switch Turn "OFF" Delay 4352 E1, E2, LE to VOS Setup Time 4351 Sn to LE Hold Time 4351 and 4352 Sn to LE Pulse Width 4351 and 4352 LE Input (Control) Capacitance Power Dissipation Capacitance (Notes 7, 8) 4351 -55oC TO 125oC SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPHZ, tPLZ CL = 50pF 0 2 - - 250 - 315 - 375 ns 0 4.5 - - 50 - 63 - 75 ns 0 6 - - 43 - 54 - 64 ns -4.5 4.5 - - 40 - 50 - 60 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 45 - 56 - 68 ns 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 48 - 60 - 71 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 60 - 75 - 90 ns 0 4.5 - - 12 - 15 - 18 ns 0 6 - - 10 - 13 - 15 ns -4.5 4.5 - - 18 - 23 - 27 ns 0 2 5 - - 5 - 5 - ns 0 4.5 5 - - 5 - 5 - ns 0 6 5 - - 5 - 5 - ns -4.5 4.5 5 - - 5 - 5 - ns 0 2 100 - - 125 - 150 - ns 0 4.5 20 - - 25 - 30 - ns 0 6 17 - - 21 - 26 - ns -4.5 4.5 25 - - 31 - 38 - ns tPHZ, tPLZ tPHZ, tPLZ tPHZ, tPLZ tSU tH tW CL = 50pF CL = 50pF CL = 50pF CI - - - - - 10 - 10 - 10 pF CPD - - 5 - 50 - - - - - pF 8 CD54/74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns (Continued) -40oC TO 85oC 25oC -55oC TO 125oC PARAMETER SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS Power Dissipation Capacitance (Notes 7, 8) 4352 CPD - - 5 - 74 - - - - - pF tPLH, tPHL CL = 50pF 0 4.5 - - 7 - 9 - 11 ns -4.5 4.5 - - 5 - 7 - 8 ns 0 4.5 - - 75 - 94 - 113 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 4.5 - - 75 - 94 - 113 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 4.5 - - 55 - 69 - 83 ns -4.5 4.5 - - 40 - 50 - 60 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 60 - 75 - 90 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 60 - 75 - 90 ns -4.5 4.5 - - 55 - 69 - 83 ns 0 4.5 - - 65 - 81 - 98 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 12 - 15 - 18 ns -4.5 4.5 - - 14 - 18 - 21 ns 0 4.5 5 - - 5 - 5 - ns -4.5 4.5 5 - - 5 - 5 - ns 0 4.5 25 - - 31 - 28 - ns -4.5 4.5 25 - - 31 - 38 - ns HCT TYPES Propagation Delay, Switch In to Switch Out Maximum Switch Turn "ON" Delay 4351 E1, E2, LE to VOS Maximum Switch Turn "ON" Delay 4351 Sn to VOS Maximum Switch Turn "OFF" Delay 4351 E1 to VOS Maximum Switch Turn "OFF" Delay 4351 E2 to VOS tPZH, tPZL tPZH, tPZL tPHZ, tPLZ tPHZ, tPLZ Maximum Switch Turn "OFF" Delay 4351 LE to VOS tPHZ, tPLZ Maximum Switch Turn "OFF" Delay 4351 Sn to VOS tPHZ, tPLZ Setup Time 4351 Sn to LE Hold Time 4351 and 4352 Sn to LE Pulse Width 4351 LE Input (Control) Capacitance Power Dissipation Capacitance (Notes 7, 8) 4351 CL = 50pF CL = 50pF CL = 50pF tW CL = 50pF CI - - - - - 10 - 10 - 10 pF CPD - - 5 - 52 - - - - - pF NOTES: 7. CPD is used to determine the dynamic power consumption, per package. 8. PD = CPD VCC2 fi + (CL + CS) VCC2 fo where fi = input frequency, fo = output frequency, CL = output load capacitance, CS = switch capacitance, VCC = supply voltage. 9 CD54/74HC4351, CD74HCT4351, CD74HC4352 Analog Channel Specifications PARAMETER Switch Input Capacitance Common Capacitance Minimum Switch Frequency Response at -3dB (Figure 5, 7) TA = 25oC TEST CONDITIONS TYPE VEE (V) VCC (V) HC/HCT UNITS CI All - - 5 pF CCOM 4351 - - 25 pF 4352 - - 12 pF 4351 - - 145 MHz 4352 -2.25 2.25 165 MHz SYMBOL fMAX Crosstalk Between Any Two Switches (Note 12) Sine-Wave Distortion E or S to Switch Feedthrough Noise Switch "OFF" Signal Feedthrough (Figure 6, 8) See Figure 11 Notes 9, 10 See Figure 10 Notes 10, 11 See Figure 12 See Figure 13 Notes 10, 11 See Figure 14 Notes 10, 11 NOTES: 9. Adjust input voltage to obtain 0dBm at VOS for, fin = 1MHz. 10. VIS is centered at (VCC - VEE)/2. 11. Adjust input for 0dBm. 12. Not applicable for 'HC4351 and CD74HCT4351. 10 4351 - - 180 MHz 4352 -4.5 4.5 185 MHz 4351 - - N/A dB 4352 -2.25 2.25 (TBE) dB 4351 - - N/A dB 4352 -4.5 4.5 (TBE) dB All -2.25 2.25 0.035 % All -4.5 4.5 0.018 % 4351 - - - mV 4352 -2.25 2.25 (TBE) mV 4351 - - - mV 4352 -4.5 4.5 (TBE) mV 4351 - - -73 dB 4352 -2.25 2.25 -65 dB 4351 - - -75 dB 4352 -4.5 4.5 -67 dB CD54/74HC4351, CD74HCT4351, CD74HC4352 Typical Performance Curves 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50 PIN 12 TO 3 -2 -4 -40 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50 PIN 12 TO 3 -6 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50 PIN 12 TO 3 -20 -60 -8 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50 PIN 12 TO 3 -80 -10 10K 100K 1M 10M FREQUENCY, f (Hz) -100 10K 100M FIGURE 5. CHANNEL ON BANDWIDTH ('HC4351, CD74HCT4351) 1M 10M FREQUENCY, f (Hz) 100M FIGURE 6. CHANNEL OFF FEEDTHROUGH ('HC4351, CD74HCT4351) 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50 PIN 4 TO 3 -2 -4 -40 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50 PIN 4 TO 3 -20 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50 PIN 4 TO 3 -6 -60 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50 PIN 4 TO 3 -80 -8 -10 10K 100K 100K 1M 10M FREQUENCY, f (Hz) -100 10K 100M 100K 1M 10M 100M FREQUENCY, f (Hz) FIGURE 7. CHANNEL ON BANDWIDTH (CD74HC4352) FIGURE 8. CHANNEL OFF FEEDTHROUGH (CD74HC4352) 11 CD54/74HC4351, CD74HCT4351, CD74HC4352 "ON" RESISTANCE, RON () Typical Performance Curves (Continued) 130 120 110 100 90 80 70 60 50 40 30 20 10 VCC - VEE = 4.5V VCC - VEE = 6V VCC - VEE = 9V 0 1 0 2 3 4 5 6 7 8 9 INPUT SIGNAL VOLTAGE, VIS (V) FIGURE 9. TYPICAL ON RESISTANCE vs INPUT SIGNAL VOLTAGE Analog Test Circuits VIS 0.1F VCC VCC SWITCH ON VIS R VOS1 R R C VOS2 SWITCH OFF R VCC/2 VCC/2 C dB METER VCC/2 fIS = 1MHz SINEWAVE R = 50 C = 10pF FIGURE 10. CROSSTALK BETWEEN TWO SWITCHES TEST CIRCUIT VCC VCC 0.1F VIS SINE WAVE 10F VIS VOS SWITCH ON 50 VCC/2 VIS SWITCH ON VI = VIH VOS 10k 10pF dB METER VCC/2 50pF DISTORTION METER fIS = 1kHz TO 10kHz FIGURE 11. FREQUENCY RESPONSE TEST CIRCUIT FIGURE 12. TOTAL HARMONIC DISTORTION TEST CIRCUIT 12 CD54/74HC4351, CD74HCT4351, CD74HC4352 Analog Test Circuits (Continued) E VCC 600 VCC/2 SWITCH ALTERNATING ON AND OFF tr, tf 6ns fCONT = 1MHz 50% DUTY CYCLE VCC VP-P VOS 0.1F 600 50pF VCC/2 SCOPE FIGURE 13. CONTROL-TO-SWITCH FEEDTHROUGH NOISE TEST CIRCUIT fIS 1MHz SINEWAVE R = 50 C = 10pF VOS SWITCH OFF VIS VOS VC = VIL R R VCC/2 VCC/2 C dB METER FIGURE 14. SWITCH OFF SIGNAL FEEDTHROUGH 13 CD54/74HC4351, CD74HCT4351, CD74HC4352 Test Circuits and Waveforms tWL + tWH = tfCL trCL tWL + tWH = trCL = 6ns tfCL = 6ns 50% 10% 10% 2.7V CLOCK 50% 50% 1.3V 0.3V 0.3V GND 1.3V 1.3V GND tWH tWL tWH tWL I fCL 3V VCC 90% CLOCK I fCL NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. FIGURE 15. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH FIGURE 16. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH tr = 6ns tf = 6ns 90% 50% 10% INPUT GND tTLH 90% INVERTING OUTPUT tPHL FIGURE 17. HC TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC trCL VCC 90% GND tH(H) 3V 2.7V 1.3V 0.3V GND tH(H) tH(L) VCC DATA INPUT DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 19. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET tfCL CLOCK INPUT 50% 10% tPLH FIGURE 18. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tfCL trCL tTLH 1.3V 10% tPLH tPHL GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL CLOCK INPUT tf = 6ns tr = 6ns VCC CL 50pF FIGURE 20. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 14 CD54/74HC4351, CD74HCT4351, CD74HC4352 Test Circuits and Waveforms 6ns (Continued) 6ns OUTPUT DISABLE tr VCC 90% 50% 10% OUTPUTS ENABLED OUTPUT HIGH TO OFF 50% OUTPUTS DISABLED FIGURE 21. HC THREE-STATE PROPAGATION DELAY WAVEFORM OTHER INPUTS TIED HIGH OR LOW OUTPUT DISABLE IC WITH THREESTATE OUTPUT GND 1.3V tPZH 90% OUTPUTS ENABLED OUTPUTS ENABLED 0.3 10% tPHZ tPZH 90% 3V tPZL tPLZ OUTPUT LOW TO OFF 50% OUTPUT HIGH TO OFF 6ns GND 10% tPHZ tf 2.7 1.3 tPZL tPLZ OUTPUT LOW TO OFF 6ns OUTPUT DISABLE 1.3V OUTPUTS DISABLED OUTPUTS ENABLED FIGURE 22. HCT THREE-STATE PROPAGATION DELAY WAVEFORM OUTPUT RL = 1k CL 50pF VCC FOR tPLZ AND tPZL GND FOR tPHZ AND tPZH NOTE: Open drain waveforms tPLZ and tPZL are the same as those for three-state shown on the left. The test circuit is Output RL = 1k to VCC, CL = 50pF. FIGURE 23. HC AND HCT THREE-STATE PROPAGATION DELAY TEST CIRCUIT 15 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated