SMA6860MZ-DS, Rev. 5 SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp/en/
Description
The SMA6860MZ inverter power module (IPM) series provides
a robust, highly-integrated solution for optimally controlling
3-phase motor power inverter systems and variable speed
control systems used in energy-conserving designs to drive
motors of residential and commercial appliances. These ICs
take 230 VAC input voltage, and up to 2.5 A (continuous)
output current. They can withstand voltages of up to 500 V
(MOSFET breakdown voltage).
The SMA6860MZ power package includes an IC with all of
the necessary power elements (six MOSFETs), pre-driver ICs
(two), and bootstrap diodes (three), needed to configure the
main circuit of an inverter. This enables the main circuit of
the inverter to be configured with fewer external components
than traditional designs.
Applications include residential white goods (home
applications) and commercial appliance motor control:
• Air conditioner fan
• Small ventilation fan
• Dishwasher pump
Features and Benefits
▪ Built-in pre-drive IC
▪ MOSFET power element
▪ Alleviate noise generation by adjusting an internal resistor
▪ CMOS compatible input (5 V)
▪ High-side gate driver using bootstrap circuit or floating
power supply
▪ Built-in protection circuit for controlling power supply
voltage drop (UVLO on VB and VCC)
▪ Overcurrent protection (OCP), overcurrent limiting (OCL),
and thermal shutdown (TSD)
▪ Output of fault signal during operation of protection circuit
▪ Output current 1.5, 2, or 2.5 A
▪ Small SIP (SMA 24-pin)
High Voltage 3-Phase Motor Drivers
Figure 1. Driver block diagram
Functional Block Diagram
Low-Side
Driver
UVLOUVLOUVLOUVLO
Input
Logic
Input Logic
(OCP Reset )
UVLO
Thermal
Shutdown
SD1
VCC1
VB1 VB2 VB3
VBB
U
V
W1
W2
LS
2LS
1SD2
COM2
LIN3
LIN2
LIN1
VCC2
COM1
HIN3
HIN2
HIN1 High-Side
Level Shift Driver
OCL
OCP and OCL
RC
OCP
Packages: Power SIP
Leadform
2451 Leadform
2452
Not to scale
A. ¯
S
¯
¯¯
D
¯
¯
1
¯
and ¯
S
¯
¯¯
D
¯
¯
2
¯
terminals are used for both input and output.
B. ¯
S
¯
¯¯
D
¯
¯
1
¯
, ¯
S
¯
¯¯
D
¯
¯
2
¯
, and ¯
O
¯
¯¯
C
¯
¯
L
¯
terminals are open-collector output. RC terminal is open-drain output.
C. Blanking Time (tblank) is used in Overcurrent Limiting (OCL) and Overcurrent Protection (OCP).
If the time exceeds the limit, the signal will be output (open-collector output turns on) on the ¯
S
¯
¯¯
D
¯
¯
2
¯
pin, and protection operation will start up.
SMA6860MZ Series
2
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Selection Guide
Part Number MOSFET Breakdown
Voltage, VDSS(min)
(V)
Output Current
Continuous, IO(max)
(A) Pulsed, IOP (max)
(A)
SMA6861MZ 250 2 3.0
SMA6862MZ 500 1.5 2.25
SMA6863MZ 500 2.5 3.75
SMA6864MZ 250 2.5 3.75
SMA6865MZ 500 2.5 3.75
All performance characteristics given are typical values for circuit or
system baseline design only and are at the nominal operating voltage and
an ambient temperature, TA, of 25°C, unless oth er wise stated.
Absolute Maximum Ratings, valid at TA = 25°C
Characteristic Symbol Remarks Rating Unit
MOSFET Breakdown Voltage VDSS
SMA6861MZ
VCC = 15 V, ID = 100 μA, VIN = 0 V
250 V
SMA6862MZ 500 V
SMA6863MZ 500 V
SMA6864MZ 250 V
SMA6865MZ 500 V
Logic Supply Voltage VCC Between VCC and COM 20 V
Bootstrap Voltage VBS Between VB and HS (U,V, and W phases) 20 V
Output Current, Continuous IO
SMA6861MZ 2 A
SMA6862MZ 1.5 A
SMA6863MZ 2.5 A
SMA6864MZ 2.5 A
SMA6865MZ 2.5 A
Output Current, Pulsed IOP
SMA6861MZ
PW ≤ 100 μs, duty cycle = 1%
3.0 A
SMA6862MZ 2.25 A
SMA6863MZ 3.75 A
SMA6864MZ 3.75 A
SMA6865MZ 3.75 A
Input Voltage VIN HINx and LINx pins –0.5 to 7 V
Pull-up Voltage for Shutdown Pins VSDX SDx pins 7 V
Pull-up Voltage for Overcurrent Limiting Pin VOCL 7V
Allowable Power Dissipation PDTC = 25°C 28 W
Thermal Resistance (Junction to Case) RθJC All elements operating 4.46 °C/W
Thermal Resistance (Junction to Ambient) RθJA All elements operating 31.25 °C/W
Case Operating Temperature TCOP –20 to 100 °C
Storage Temperature Tstg –40 to 150 °C
3
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Recommended Operating Conditions
Characteristic Symbol Remarks Min. Typ. Max. Units
Main Supply Voltage VBB
SMA6861MZ
Between VBB and LS
– – 200 V
SMA6862MZ – – 400 V
SMA6863MZ – – 400 V
SMA6864MZ – – 200 V
SMA6865MZ – – 400 V
VBB Snubber Capacitor CSB 0.01 – 0.1 μF
Logic Supply Voltage VCC Between VCC and COM 13.5 15 16.5 V
Zener Voltage for VCCx Pins VZBetween VCC and COM 18 – 20 V
Pull-up Voltage VSDx, VOCL 4.5 5 5.5 V
Pull-up Resistor ¯
S
¯
¯¯
D
¯
¯
2
¯
Pin RUP2 3.3 – 10 kΩ
Pull-up Resistor ¯
O
¯
¯¯
C
¯
¯
L
¯
Pin RUP1 1 – 10 kΩ
Pull-up Resistor RC Pin RR33 – 390 kΩ
Capacitor ¯
S
¯
¯¯
D
¯
¯
x
¯
and ¯
O
¯
¯¯
C
¯
¯
L
¯
Pins CSDX 1 – 10 nF
Capacitor RC Pin CC 1 – 4.7 nF
Dead Time tdead TJ = –20°C to 150°C 1.5 – – μs
Minimum Input Pulse Width IINMIN(on) TJ = –20°C to 150°C 0.5 – – μs
IINMIN(off) TJ = –20°C to 150°C 0.5 – – μs
Switching Frequency fPWM – – 20 kHz
4
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
VCC2
LIN1
VCC1
HIN 1
COM1
VB1
HO 3
HS3
LIN2
LIN3
SD 2
COM 2
LO 1
LO 2
LO 3
M
MCU
15 V
HVIC
LVIC
HIN 2
HIN 3
VB2 VB3
HO 2
HO 1
HS1
HS2
10
13
4
5
6
7
8
24
12
11
13
16
17
14
23
22
19
18
20
21
OCL
2
SD1
9
RC
15
RUP1
5V
5V
RUP2
DZ1
DZ2
RS
5V
CC
RR
CSD1
CSD2
CSB
SMA6860MZ
Typical Application Diagram
NOTE:
The external electrolytic capacitors should be placed as close to the IC as possible, in order to avoid malfunctions
from external noise interference. Put a ceramic capacitor in parallel with the electrolytic capacitor if further
reduction of noise susceptibility is necessary.
Shows configuration for implementing current
limiter function: ¯
O
¯
¯¯
C
¯
¯
L
¯
and ¯
S
¯
¯¯
D
¯
¯
1
¯
pins tied together
5
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
VCC2
LIN1
VCC1
HIN1
COM1
VB1
HO3
HS3
LIN2
LIN3
SD2
COM2
LO1
LO2
LO3
M
15V
HVIC
LVIC
HIN2
HIN3
VB2 VB3
HO2
HO1
HS1
HS2
10
13
4
5
6
7
8
24
12
11
13
16
17
14
23
22
19
18
20
21
OCL
2
SD1
9
RC
15
Rup1
5V
ZD
ZD
RS
VRC
CC
RR
CSD
Rup
Typical Application Diagram
NOTE:
The external electrolytic capacitors should be placed as close to the IC as possible, in order to avoid malfunctions
from external noise interference. Put a ceramic capacitor in parallel with the electrolytic capacitor if further
reduction of noise susceptibility is necessary.
Shows configuration without current limiter
function: ¯
S
¯
¯¯
D
¯
¯
1
¯
and ¯
S
¯
¯¯
D
¯
¯
2
¯
pins tied together
6
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
ELECTRICAL CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Logic Supply Current ICC VCC = 15 V, TC = –20°C to 125°C – 2.7 5.0 mA
Bootstrap Supply Current IBX VBX = 15 V, VHIN = 5 V, TC = –20°C to 125°C – 135 380 μA
Input Voltage VIH VCC = 15 V – 2.9 3.4 V
VIL VCC = 15 V 1.6 2.1 – V
Input Voltage Hysteresis VIhys VCC = 15 V – 0.8 – V
Input Current IIN VIN = 5 V – 230 500 μA
Undervoltage Lock Out
VUVHL High side, between VBx and U, V, or W 9.0 10.0 11.0 V
VUVHH 9.5 10.5 11.5 V
VUVHhys High side, hysteresis – 0.5 – V
VUVLL Low side, between VCC2 and COM2 10.0 11.0 12.0 V
VUVLH 10.5 11.5 12.5 V
VUVLhys Low side, hysteresis – 0.5 – V
¯
S
¯
¯¯
D
¯
¯
x
¯
and ¯
O
¯
¯¯
C
¯
¯
L
¯
Output Voltage VSDX(on),
VOCL VSDX = VOCL = 5 V, RUPX = 3.3 kΩ– – 0.6 V
Overtemperature DetectionThreshold
Temperature (Activation and
Deactivation)
TDH
VCC = 15 V, high-side and low side
120 135 150 °C
TDL 100 115 130 °C
TDhys –20–°C
Overcurrent Protection Trip Voltage VTRIP VCC = 15 V 0.9 1.0 1.1 V
Overcurrent Limit Reference Voltage VLIM VCC = 15 V 0.5035 0.53 0.5565 V
Overcurrent Protection Hold Time tpVRC = 5 V, RR = 360 kΩ, CC = 0.0047 μF – 2.0 – ms
Blanking Time tblank VCC = 15 V – 2.0 – μs
Bootstrap Diode Leakage Current ILBD
SMA6861MZ VR = 250 V – – 10 μA
SMA6862MZ VR = 500 V – – 10 μA
SMA6863MZ VR = 500 V – – 10 μA
SMA6864MZ VR = 250 V – – 10 μA
SMA6865MZ VR = 500 V – – 10 μA
Bootstrap Diode Forward Voltage VFBD IF = 0.05 A – 0.8 1.3 V
Bootstrap Diode Recovery Time trrb IF / IRP = 100 mA / 100 mA – 70 – ns
Bootstrap Diode Series Resistor RBD 168 210 252 Ω
MOSFET Breakdown Voltage VDSS
SMA6861MZ
VCC = 15 V, ID = 100 μA, VIN = 0 V
250 – – V
SMA6862MZ 500 – – V
SMA6863MZ 500 – – V
SMA6864MZ 250 – – V
SMA6865MZ 500 – – V
MOSFET Leakage Current IDSS
SMA6861MZ VCC = 15 V, VDS = 250 V, VIN = 0 V – – 100 μA
SMA6862MZ VCC = 15 V, VDS = 500 V, VIN = 0 V – – 100 μA
SMA6863MZ VCC = 15 V, VDS = 500 V, VIN = 0 V – – 100 μA
SMA6864MZ VCC = 15 V, VDS = 250 V, VIN = 0 V – – 100 μA
SMA6865MZ VCC = 15 V, VDS = 500 V, VIN = 0 V – – 100 μA
Continued on the next page…
7
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
ELECTRICAL CHARACTERISTICS (continued), valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
MOSFET On State Resistance RDS(on)
SMA6861MZ VCC = 15 V, ID = 1.0 A, VIN = 5 V – 1.25 1.5 Ω
SMA6862MZ VCC = 15 V, ID = 0.75 A, VIN = 5 V – 3.2 4.0 Ω
SMA6863MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 2.0 2.4 Ω
SMA6864MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 0.35 0.5 Ω
SMA6865MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 1.4 1.7 Ω
MOSFET Diode Forward Voltage VSDF
SMA6861MZ VCC = 15 V, ID = 1.0 A, VIN = 5 V – 1.1 1.5 V
SMA6862MZ VCC = 15 V, ID = 0.75 A, VIN = 5 V – 1.1 1.5 V
SMA6863MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 1.1 1.5 V
SMA6864MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 0.8 1.2 V
SMA6865MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 1.0 1.5 V
8
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
SMA6861MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Switching Time, High Side
tdH(on)
VBB = 150 V, VCC = 15 V, ID = 2.0 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 660 – ns
trH –25–ns
trrH –50–ns
tdH(off) – 560 – ns
tfH –10–ns
Switching Time, Low Side
tdL(on)
VBB = 150 V, VCC = 15 V, ID = 2.0 A, 0 V ≤ VIN ≤ 5 V ,
inductive load
– 540 – ns
trL –25–ns
trrL –45–ns
tdL(off) – 500 – ns
tfL –15–ns
SMA6862MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Switching Time, High Side
tdH(on)
VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 720 – ns
trH –60–ns
trrH – 110 – ns
tdH(off) – 690 – ns
tfH –30–ns
Switching Time, Low Side
tdL(on)
VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 670 – ns
trL –70–ns
trrL – 120 – ns
tdL(off) – 590 – ns
tfL –30–ns
SMA6863MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Switching Time, High Side
tdH(on)
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 820 – ns
trH – 100 – ns
trrH – 120 – ns
tdH(off) – 740 – ns
tfH –30–ns
Switching Time, Low Side
tdL(on)
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 790 – ns
trL – 110 – ns
trrL – 130 – ns
tdL(off) – 700 – ns
tfL –30–ns
9
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
SMA6864MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Switching Time, High Side
tdH(on)
VBB = 150 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 730 – ns
trH –40–ns
trrH –75–ns
tdH(off) – 640 – ns
tfH –20–ns
Switching Time, Low Side
tdL(on)
VBB = 150 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 660 – ns
trL –40–ns
trrL –55–ns
tdL(off) – 600 – ns
tfL –30–ns
SMA6865MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol Conditions Min Typ Max Units
Switching Time, High Side
tdH(on)
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 750 – ns
trH –60–ns
trrH – 100 – ns
tdH(off) – 680 – ns
tfH –20–ns
Switching Time, Low Side
tdL(on)
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
inductive load
– 640 – ns
trL –65–ns
trrL – 100 – ns
tdL(off) – 560 – ns
tfL –20–ns
VDS
ID
Switching Characteristics Definitions
10
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Truth Table
Mode Hin Lin H-side MOSFET L-side MOSFET
Normal
L L Off Off
H L On Off
L H Off On
H H On On
TSD
L L Off Off
H L On Off
L H Off Off
H H On Off
OCP
L L Off Off
H L On Off
L H Off Off
H H On Off
OCL ( = L )1
L L Off Off
H L Off Off
L H Off On
H H Off On
UVLO ( VCC )2
L L Off Off
H L Off Off
L H Off Off
H H Off Off
UVLO ( VB )3
L L Off Off
H L Off Off
L H Off On
H H Off On
SD2 ( = L )
L L Off Off
H L On Off
L H Off Off
H H On Off
1The OCL feature is enabled when the ¯
O
¯
¯¯
C
¯
¯
L
¯
and ¯
S
¯
¯¯
D
¯
¯
1
¯
pins are tied together externally. If these pins are not tied when an
OCL condition occurs, device operation continues in Normal mode.
2Returning to the Normal mode of operation from a VCC UVLO condition, a high-side MOSFET resumes switching
on the rising edge of an HINx input. On the other hand, a low-side MOSFET resumes switching on the first logic high
of a LINx input after release of the UVLO condition.
3Returning to the Normal mode of operation from a VB UVLO condition, a high-side MOSFET resumes switching on the rising
edge of an HINx input.
Note: To prevent a shoot-through condition, the external microcontroller should not drive HINx = LINx = H at the same time.
11
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
LIN
LO
LS1
SD2
tblank
RC
Slope defined by R
C
, C
C
OCP
Release
tp
3.5 V
VTRIP
OCP Timing Diagram
Low-Side Logic TSD Timing Diagram
Open-collector output transistor
turned on
12
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
LIN
SD2
VCC2 UVLL
UVLH
LO
UVLH
Open-collector output transistor
turned on
High-Side UVLO Timing Diagram
Low-Side UVLO Timing Diagram
13
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
OCL Timing Diagram
¯
O
¯
¯¯
C
¯
¯
L
¯
and ¯
S
¯
¯¯
D
¯
¯
1
¯
pins connected externally; current-limiter function in use
LIN(a)
LO
LS1
SD2
RC
VTRIP (1 V)
VOCL (0.5 V)
3.5 V
OCL,
SD1
2 μs
VTH (2.1 V) VTH (2.1 V)
VTH (2.9 V) VTH (2.9 V)
VTH (2.9 V)
2 μs
5 μs
2 μs
T= 50
CSD1
T= 50
CC
T= RUP1×CSD1 T= RUP1×CSD1
T= RR×CC
T= RUP2×CSD2
HIN(a)
HO 3.3 μs3.3 μs
Low-side shutdown
High-side
shutdown
Enable resumption of high-side
operation at next HIN rising edge
Enable resumption of low-side
operation at next LIN rising edge
High-side
shutdown
T= 50
CSD2
(a) Each HINx or LINx pin drives a independent side of a phase, that is, the high-side and the low-side swtiching
devices of a U, V, or W motor coil phase are each driven separately, by the corresponding dedicated HINx or LIN
x
14
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Shut Down Timing Diagram
¯
S
¯
¯¯
D
¯
¯
1
¯
and ¯
S
¯
¯¯
D
¯
¯
2
¯
pins connected externally; current-limiter function not in use
Slope defined by RC, CC
LIN(a)
HIN(a)
(a) Each HINx or LINx pin drives a independent side of a phase, that is, the high-side and th
e
low-side swtiching devices of a U, V, or W motor coil phase are each driven separately, by th
e
corresponding dedicated HINx or LINx input
15
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
1 3 5 7 9 11131517192123
2 4 6 8 10 12 14 16 18 20 22 24
Chamfer Side
Leadform 2452
Leadform 2451
Chamfer on Opposite Side
1357911131517192123
24681012141618202224
Pin-out Diagrams
Terminal List Table
Number Name Function
1 VB1 High side bootstrap terminal (U phase)
2 VB2 High side bootstrap terminal (V phase)
3 VB3 High side bootstrap terminal (W phase)
4 VCC1 High side logic supply voltage
5¯
S
¯
¯¯
D
¯
¯
1
¯ High side shutdown input and UVLO fault signal output
6 COM1 High side logic GND terminal
7 HIN3 High side input terminal (W phase)
8 HIN2 High side input terminal (V phase)
9 HIN1 High side input terminal (U phase)
10 VBB Main supply voltage
11 W1 Output of W phase (connect to W2 externally)
12 V Output of V phase
13 W2 Output of W phase (connect to W1 externally)
14 LS2 Low side source terminal (connect to LS1 externally)
15 RC Overcurrent protection hold time adjustment input terminal
16 LS1 Low side source terminal (connect to LS2 externally)
17 ¯
O
¯
¯¯
C
¯
¯
L
¯ Output for overcurrent limiting
18 LIN3 Low side input terminal (W phase)
19 LIN2 Low side input terminal (V phase)
20 LIN1 Low side input terminal (U phase)
21 COM2 Low side GND terminal
22 ¯
S
¯
¯¯
D
¯
¯
2
¯ Low side shutdown input and overtemperature, overcurrent, and UVLO fault signals output
23 VCC2 Low side logic supply voltage
24 U Output of U phase
16
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
1.27 ±0.1
24681012141618202224
1 3 5 7 9 11 13 15 17 19 21 23
4 ±0.2
10.2 ±0.2
R0.65
MIN
PCB
Surface
4.4
REF
2.2 ±0.7
BSC
2.2 ±0.7
BSC
3 ±0.5
BSC
1.2 ±0.1
BSC
A
C
C
Measured at pin exit from case
Maximum dambar protrusion
0.6 +0.15
– 0.05
0.7 +0.15
– 0.05
0 to 0.55
0 to 0.55
A
1.27 ±0.6
29.21 ±0.7
B
BMeasured at pin tips
31 ±0.2
31.3 ±0.2
Gate protrusion
View A
View A
2X Gate protrusion
2X Exposed
tie bar
Leadform: 2451
Terminal core material: Cu
Terminal plating: Ni and solder (Sn 97.5%, Ag 2.5%) plating
Case material: Epoxy resin
Dimensions in millimeters
Branding Area
Branding codes (exact appearance at manufacturer discretion):
1st line, lot: YMDD#
Where: Y is the last digit of the year of manufacture
M is the month (1 to 9, O, N, D)
DD is the date
# is the tracking letter
2nd line, type: SMA686xMZ
Leadframe plating Pb-free. Device composition
complies with the RoHS directive.
Package Outline Drawing
Leadform 2451
Dual rows, 24 alternating pins; pins bent 90° for horizontal case mounting; pin #1 in outer row
17
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Leadform: 2452
Terminal core material: Cu
Terminal plating: Ni
Recommended attachment: Solder dip (Sn-Ag-Cu)
Dimensions in millimeters
Branding Area
Branding codes (exact appearance at manufacturer discretion):
1st line, lot: YMDD#
Where: Y is the last digit of the year of manufacture
M is the month (1 to 9, O, N, D)
DD is the date
# is the tracking letter
2nd line, type: SMA686xMZ
31 ±0.2
31.3 ±0.2
Gate protrusion
1.27 ±0.5
0.6 +0.15
– 0.05
0.5 +0.15
– 0.05
9.5 +0.7
– 0.5
10.2 ±0.2
A
A
Measured at pin tips
2 4 6 8 1012141618202224
1 3 5 7 9 11 13 15 17 19 21 23
4 ±0.2
R1
REF
4.5
REF
4.5 ±0.5
5 ±0.5
1.2 ±0.1
BSC
View A
Deflection at pin bend
0.7 MAX
0.7 MAX
View A
2X Gate protrusion
2X Exposed
tie bar
29.21 ±0.6
Package Outline Drawing
Leadform 2452
Dual rows, 24 alternating pins; vertical case mounting; pin #1 opposite chamfer side
Leadframe plating Pb-free. Device composition
complies with the RoHS directive.
18
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
Because reliability can be affected adversely by improper storage
environments and handling methods, please observe the following
cautions.
Cautions for Storage
• Ensure that storage conditions comply with the standard
temperature (5°C to 35°C) and the standard relative humidity
(around 40 to 75%); avoid storage locations that experience
extreme changes in temperature or humidity.
• Avoid locations where dust or harmful gases are present and
avoid direct sunlight.
• Reinspect for rust on leads and solderability of products that have
been stored for a long time.
Cautions for Testing and Handling
When tests are carried out during inspection testing and other
standard test periods, protect the products from power surges
from the testing device, shorts between adjacent products, and
shorts to the heatsink.
Remarks About Using Silicone Grease with a Heatsink
• When silicone grease is used in mounting this product on a
heatsink, it shall be applied evenly and thinly. If more silicone
grease than required is applied, it may produce stress.
• Volatile-type silicone greases may permeate the product and
produce cracks after long periods of time, resulting in reduced
heat radiation effect, and possibly shortening the lifetime of the
product.
• Our recommended silicone greases for heat radiation purposes,
which will not cause any adverse effect on the product life, are
indicated below:
Type Suppliers
G746 Shin-Etsu Chemical Co., Ltd.
YG6260 Momentive Performance Materials
SC102 Dow Corning Toray Silicone Co., Ltd.
Soldering
• When soldering the products, please be sure to minimize the
working time, within the following limits:
260±5°C 10 s
380±5°C 5 s
• Soldering iron should be at a distance of at least 1.5 mm from the
body of the products
Electrostatic Discharge
• When handling the products, operator must be grounded.
Grounded wrist straps worn should have at least 1 MΩ of
resistance to ground to prevent shock hazard.
• Workbenches where the products are handled should be
grounded and be provided with conductive table and floor mats.
• When using measuring equipment such as a curve tracer, the
equipment should be grounded.
• When soldering the products, the head of soldering irons or the
solder bath must be grounded in other to prevent leak voltages
generated by them from being applied to the products.
• The products should always be stored and transported in our
shipping containers or conductive containers, or be wrapped in
aluminum foil.
19
SANKEN ELECTRIC CO., LTD.
High Voltage 3-Phase Motor Drivers
SMA6860MZ Series
SMA6860MZ-DS, Rev. 5
• The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the
latest revision of the document before use.
• Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod-
ucts herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or
any other rights of Sanken or any third party which may result from its use.
• Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semicon-
ductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures
including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device
failure or malfunction.
• Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equip-
ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.).
When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and
its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever
long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales
representative to discuss, prior to the use of the products herein.
The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required
(aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.
• In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the
degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the
load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general,
derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such
as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses,
instantaneous values, maximum values and minimum values must be taken into consideration.
In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of
derating of junction temperature affects the reliability significantly.
• When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically
or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance
and proceed therewith at your own responsibility.
• Anti radioactive ray design is not considered for the products listed herein.
• Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribu-
tion network.
• The contents in this document must not be transcribed or copied without Sanken's written consent.
