Datasheet PD44165084B PD44165094B PD44165184B PD44165364B 18M-BIT QDRTM II SRAM 4-WORD BURST OPERATION R10DS0018EJ0200 Rev.2.00 October 6, 2011 Description The PD44165084B is a 2,097,152-word by 8-bit, the PD44165094B is a 2,097,152-word by 9-bit, the PD44165184B is a 1,048,576-word by 18-bit and the PD44165364B is a 524,288-word by 36-bit synchronous quad data rate static RAM fabricated with advanced CMOS technology using full CMOS six-transistor memory cell. The PD44165084B, PD44165094B, PD44165184B and PD44165364B integrate unique synchronous peripheral circuitry and a burst counter. All input registers controlled by an input clock pair (K and K#) are latched on the positive edge of K and K#. These products are suitable for application which require synchronous operation, high speed, low voltage, high density and wide bit configuration. These products are packaged in 165pin PLASTIC BGA. Features * 1.8 0.1 V power supply * 165-pin PLASTIC BGA (13 x 15) * HSTL interface * PLL circuitry for wide output data valid window and future frequency scaling * Separate independent read and write data ports with concurrent transactions * 100% bus utilization DDR READ and WRITE operation * Four-tick burst for reduced address frequency * Two input clocks (K and K#) for precise DDR timing at clock rising edges only * Two output clocks (C and C#) for precise flight time and clock skew matching-clock and data delivered together to receiving device * Internally self-timed write control * Clock-stop capability. Normal operation is restored in 20 s after clock is resumed. * User programmable impedance output (35 to 70 ) * Fast clock cycle time : 3.3 ns (300 MHz), 3.5 ns (287 MHz), 4.0 ns (250 MHz), 5.0 ns (200 MHz) * Simple control logic for easy depth expansion * JTAG 1149.1 compatible test access port R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 1 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Ordering Information 1/2 Part No. PD44165084BF5-E33-EQ3-A PD44165084BF5-E35-EQ3-A PD44165084BF5-E40-EQ3-A PD44165084BF5-E50-EQ3-A PD44165094BF5-E33-EQ3-A PD44165094BF5-E35-EQ3-A PD44165094BF5-E40-EQ3-A PD44165094BF5-E50-EQ3-A PD44165184BF5-E33-EQ3-A PD44165184BF5-E35-EQ3-A PD44165184BF5-E40-EQ3-A PD44165184BF5-E50-EQ3-A PD44165364BF5-E33-EQ3-A PD44165364BF5-E35-EQ3-A PD44165364BF5-E40-EQ3-A PD44165364BF5-E50-EQ3-A PD44165084BF5-E33-EQ3 PD44165084BF5-E35-EQ3 PD44165084BF5-E40-EQ3 PD44165084BF5-E50-EQ3 PD44165094BF5-E33-EQ3 PD44165094BF5-E35-EQ3 PD44165094BF5-E40-EQ3 PD44165094BF5-E50-EQ3 PD44165184BF5-E33-EQ3 PD44165184BF5-E35-EQ3 PD44165184BF5-E40-EQ3 PD44165184BF5-E50-EQ3 PD44165364BF5-E33-EQ3 PD44165364BF5-E35-EQ3 PD44165364BF5-E40-EQ3 PD44165364BF5-E50-EQ3 R10DS0018EJ0200 Rev.2.00 October 6, 2011 Organization (word x bit) 2M x 8 2M x 9 1M x 18 512K x 36 2M x 8 2M x 9 1M x 18 512K x 36 Clock frequency Operating Ambient Temperature 3.3ns 300MHz Ta = 0 to 70C 3.5ns 287MHz Cycle time Package 165-pin PLASTIC BGA 4.0ns 250MHz (13 x 15) 5.0ns 200MHz Lead-free 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz PLASTIC BGA 4.0ns 250MHz (13 x 15) 5.0ns 200MHz Lead 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz Ta = 0 to 70C 165-pin Page 2 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Ordering Information 2/2 Part No. PD44165084BF5-E33Y-EQ3-A PD44165084BF5-E35Y-EQ3-A PD44165084BF5-E40Y-EQ3-A PD44165084BF5-E50Y-EQ3-A PD44165094BF5-E33Y-EQ3-A PD44165094BF5-E35Y-EQ3-A PD44165094BF5-E40Y-EQ3-A PD44165094BF5-E50Y-EQ3-A PD44165184BF5-E33Y-EQ3-A PD44165184BF5-E35Y-EQ3-A PD44165184BF5-E40Y-EQ3-A PD44165184BF5-E50Y-EQ3-A PD44165364BF5-E33Y-EQ3-A PD44165364BF5-E35Y-EQ3-A PD44165364BF5-E40Y-EQ3-A PD44165364BF5-E50Y-EQ3-A PD44165084BF5-E33Y-EQ3 PD44165084BF5-E35Y-EQ3 PD44165084BF5-E40Y-EQ3 PD44165084BF5-E50Y-EQ3 PD44165094BF5-E33Y-EQ3 PD44165094BF5-E35Y-EQ3 PD44165094BF5-E40Y-EQ3 PD44165094BF5-E50Y-EQ3 PD44165184BF5-E33Y-EQ3 PD44165184BF5-E35Y-EQ3 PD44165184BF5-E40Y-EQ3 PD44165184BF5-E50Y-EQ3 PD44165364BF5-E33Y-EQ3 PD44165364BF5-E35Y-EQ3 PD44165364BF5-E40Y-EQ3 PD44165364BF5-E50Y-EQ3 R10DS0018EJ0200 Rev.2.00 October 6, 2011 Organization (word x bit) 2M x 8 2M x 9 1M x 18 512K x 36 2M x 8 2M x 9 1M x 18 512K x 36 Cycle time Clock frequency Operating Ambient Temperature Ta = -40 to 85C Package 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz (13 x 15) 5.0ns 200MHz Lead-free 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 165-pin PLASTIC BGA 3.3ns 300MHz 3.5ns 287MHz PLASTIC BGA 4.0ns 250MHz (13 x 15) 5.0ns 200MHz Lead 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz 3.3ns 300MHz 3.5ns 287MHz 4.0ns 250MHz 5.0ns 200MHz Ta = -40 to 85C 165-pin Page 3 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Pin Arrangement 165-pin PLASTIC BGA (13 x 15) (Top View) [PD44165084B] 2M x 8 1 2 3 4 5 6 7 8 9 10 11 A CQ# VSS/72M A W# NW1# K# NC/144M R# A VSS/36M CQ B NC NC NC A NC/288M K NW0# A NC NC Q3 C NC NC NC VSS A NC A VSS NC NC D3 D NC D4 NC VSS VSS VSS VSS VSS NC NC NC E NC NC Q4 VDDQ VSS VSS VSS VDDQ NC D2 Q2 F NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC G NC D5 Q5 VDDQ VDD VSS VDD VDDQ NC NC NC H DLL# VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC VDDQ VDD VSS VDD VDDQ NC Q1 D1 K NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC L NC Q6 D6 VDDQ VSS VSS VSS VDDQ NC NC Q0 M NC NC NC VSS VSS VSS VSS VSS NC NC D0 N NC D7 NC VSS A A A VSS NC NC NC P NC NC Q7 A A C A A NC NC NC R TDO TCK A A A C# A A A TMS TDI A : Address inputs TMS : IEEE 1149.1 Test input D0 to D7 : Data inputs TDI : IEEE 1149.1 Test input Q0 to Q7 : Data outputs TCK : IEEE 1149.1 Clock input R# : Read input TDO : IEEE 1149.1 Test output W# : Write input VREF : HSTL input reference input NW0#, NW1# : Nibble Write data select VDD : Power Supply K, K# : Input clock VDDQ : Power Supply C, C# : Output clock VSS : Ground CQ, CQ# : Echo clock NC : No connection ZQ : Output impedance matching NC/xxM : Expansion address for xxMb DLL# : PLL disable Remarks 1. xxx# indicates active LOW. 2. Refer to Package Dimensions for the index mark. 3. 2A, 7A, 10A and 5B are expansion addresses : 10A for 36Mb : 10A and 2A for 72Mb : 10A, 2A and 7A for 144Mb : 10A, 2A, 7A and 5B for 288Mb. 2A and 10A of this product can also be used as NC. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 4 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Pin Arrangement 165-pin PLASTIC BGA (13 x 15) (Top View) [PD44165094B] 2M x 9 1 2 3 4 5 6 7 8 9 10 11 A CQ# VSS/72M A W# NC K# NC/144M R# A VSS/36M CQ B NC NC NC A NC/288M K BW0# A NC NC Q4 C NC NC NC VSS A NC A VSS NC NC D4 D NC D5 NC VSS VSS VSS VSS VSS NC NC NC E NC NC Q5 VDDQ VSS VSS VSS VDDQ NC D3 Q3 F NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC G NC D6 Q6 VDDQ VDD VSS VDD VDDQ NC NC NC H DLL# VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC VDDQ VDD VSS VDD VDDQ NC Q2 D2 K NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC L NC Q7 D7 VDDQ VSS VSS VSS VDDQ NC NC Q1 M NC NC NC VSS VSS VSS VSS VSS NC NC D1 N NC D8 NC VSS A A A VSS NC NC NC P NC NC Q8 A A C A A NC D0 Q0 R TDO TCK A A A C# A A A TMS TDI A : Address inputs TMS : IEEE 1149.1 Test input D0 to D8 : Data inputs TDI : IEEE 1149.1 Test input Q0 to Q8 : Data outputs TCK : IEEE 1149.1 Clock input R# : Read input TDO : IEEE 1149.1 Test output W# : Write input VREF : HSTL input reference input BW0# : Byte Write data select VDD : Power Supply K, K# : Input clock VDDQ : Power Supply C, C# : Output clock VSS : Ground CQ, CQ# : Echo clock NC : No connection ZQ : Output impedance matching NC/xxM : Expansion address for xxMb DLL# : PLL disable Remarks 1. xxx# indicates active LOW. 2. Refer to Package Dimensions for the index mark. 3. 2A, 7A, 10A and 5B are expansion addresses : 10A for 36Mb : 10A and 2A for 72Mb : 10A, 2A and 7A for 144Mb : 10A, 2A, 7A and 5B for 288Mb. 2A and 10A of this product can also be used as NC R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 5 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Pin Arrangement 165-pin PLASTIC BGA (13 x 15) (Top View) [PD44165184B] 1M x 18 1 2 3 4 5 6 7 8 9 10 11 W# BW1# K# NC/288M R# A VSS/72M CQ A CQ# B NC Q9 D9 A NC K BW0# A NC NC Q8 C NC NC D10 VSS A NC A VSS NC Q7 D8 D NC D11 Q10 VSS VSS VSS VSS VSS NC NC D7 E NC NC Q11 VDDQ VSS VSS VSS VDDQ NC D6 Q6 F NC Q12 D12 VDDQ VDD VSS VDD VDDQ NC NC Q5 G NC D13 Q13 VDDQ VDD VSS VDD VDDQ NC NC D5 H DLL# VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC D14 VDDQ VDD VSS VDD VDDQ NC Q4 D4 K NC NC Q14 VDDQ VDD VSS VDD VDDQ NC D3 Q3 L NC Q15 D15 VDDQ VSS VSS VSS VDDQ NC NC Q2 M NC NC D16 VSS VSS VSS VSS VSS NC Q1 D2 N NC D17 Q16 VSS A A A VSS NC NC D1 P NC NC Q17 A A C A A NC D0 Q0 R TDO TCK A A A C# A A A TMS TDI VSS/144M NC/36M A D0 to D17 Q0 to Q17 R# W# BW0#, BW1# K, K# C, C# CQ, CQ# ZQ DLL# : Address inputs : Data inputs : Data outputs : Read input : Write input : Byte Write data select : Input clock : Output clock : Echo clock : Output impedance matching : PLL disable TMS TDI TCK TDO VREF VDD VDDQ VSS NC NC/xxM : IEEE 1149.1 Test input : IEEE 1149.1 Test input : IEEE 1149.1 Clock input : IEEE 1149.1 Test output : HSTL input reference input : Power Supply : Power Supply : Ground : No connection : Expansion address for xxMb Remarks 1. xxx# indicates active LOW. 2. Refer to Package Dimensions for the index mark. 3. 2A, 3A, 7A and 10A are expansion addresses : 3A for 36Mb : 3A and 10A for 72Mb : 3A, 10A and 2A for 144Mb : 3A, 10A, 2A and 7A for 288Mb 2A and 10A of this product can also be used as NC R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 6 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Pin Arrangement 165-pin PLASTIC BGA (13 x 15) (Top View) [PD44165364B] 512K x 36 1 2 3 4 5 6 7 8 W# BW2# K# BW1# R# 9 10 11 A CQ# B Q27 Q18 D18 A BW3# K BW0# A D17 Q17 Q8 C D27 Q28 D19 VSS A NC A VSS D16 Q7 D8 D D28 D20 Q19 VSS VSS VSS VSS VSS Q16 D15 D7 E Q29 D29 Q20 VDDQ VSS VSS VSS VDDQ Q15 D6 Q6 F Q30 Q21 D21 VDDQ VDD VSS VDD VDDQ D14 Q14 Q5 G D30 D22 Q22 VDDQ VDD VSS VDD VDDQ Q13 D13 D5 H DLL# VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J D31 Q31 D23 VDDQ VDD VSS VDD VDDQ D12 Q4 D4 K Q32 D32 Q23 VDDQ VDD VSS VDD VDDQ Q12 D3 Q3 L Q33 Q24 D24 VDDQ VSS VSS VSS VDDQ D11 Q11 Q2 M D33 Q34 D25 VSS VSS VSS VSS VSS D10 Q1 D2 N D34 D26 Q25 VSS A A A VSS Q10 D9 D1 P Q35 D35 Q26 A A C A A Q9 D0 Q0 R TDO TCK A A A C# A A A TMS TDI VSS/288M NC/72M NC/36M VSS/144M A : Address inputs TMS : IEEE 1149.1 Test input D0 to D35 : Data inputs TDI : IEEE 1149.1 Test input Q0 to Q35 : Data outputs TCK : IEEE 1149.1 Clock input R# : Read input TDO : IEEE 1149.1 Test output W# : Write input VREF : HSTL input reference input BW0# to BW3# : Byte Write data select VDD : Power Supply K, K# : Input clock VDDQ : Power Supply C, C# : Output clock VSS : Ground CQ, CQ# : Echo clock NC : No connection ZQ : Output impedance matching NC/xxM : Expansion address for xxMb DLL# : PLL disable CQ Remarks 1. xxx# indicates active LOW. 2. Refer to Package Dimensions for the index mark. 3. 2A, 3A and 10A are expansion addresses : 9A for 36Mb : 9A and 3A for 72Mb : 9A, 3A and 10A for 144Mb : 9A, 3A, 10A and 2A for 288Mb 2A and 10A of this product can also be used as NC. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 7 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Pin Description (1/2) Symbol Type A Input D0 to Dxx Input Q0 to Qxx Output R# Input W# Input BWx# NWx# Input K, K# Input C, C# Input R10DS0018EJ0200 Rev.2.00 October 6, 2011 Description Synchronous Address Inputs: These inputs are registered and must meet the setup and hold times around the rising edge of K. All transactions operate on a burst of four words (two clock periods of bus activity). These inputs are ignored when device is deselected, i.e., NOP (R# = W# = HIGH). Synchronous Data Inputs: Input data must meet setup and hold times around the rising edges of K and K# during WRITE operations. See Pin Arrangement for ball site location of individual signals. x8 device uses D0 to D7. x9 device uses D0 to D8. x18 device uses D0 to D17. x36 device uses D0 to D35. Synchronous Data Outputs: Output data is synchronized to the respective C and C# or to K and K# rising edges if C and C# are tied HIGH. Data is output in synchronization with C and C# (or K and K#), depending on the R# command. See Pin Arrangement for ball site location of individual signals. x8 device uses Q0 to Q7. x9 device uses Q0 to Q8. x18 device uses Q0 to Q17. x36 device uses Q0 to Q35. Synchronous Read: When LOW this input causes the address inputs to be registered and a READ cycle to be initiated. This input must meet setup and hold times around the rising edge of K. If a READ command (R# = LOW) is input, an input of R# on the subsequent rising edge of K is ignored. Synchronous Write: When LOW this input causes the address inputs to be registered and a WRITE cycle to be initiated. This input must meet setup and hold times around the rising edge of K. If a WRITE command (W# = LOW) is input, an input of W# on the subsequent rising edge of K is ignored. Synchronous Byte Writes (Nibble Writes on x8): When LOW these inputs cause their respective byte or nibble to be registered and written during WRITE cycles. These signals must meet setup and hold times around the rising edges of K and K# for each of the two rising edges comprising the WRITE cycle. See Pin Arrangement for signal to data relationships. x8 device uses NW0#, NW1#. x9 device uses BW0#. x18 device uses BW0#, BW1#. x36 device uses BW0# to BW3#. See Byte Write Operation for relation between BWx#, NWx# and Dxx. Input Clock: This input clock pair registers address and control inputs on the rising edge of K, and registers data on the rising edge of K and the rising edge of K#. K# is ideally 180 degrees out of phase with K. All synchronous inputs must meet setup and hold times around the clock rising edges. Output Clock: This clock pair provides a user controlled means of tuning device output data. The rising edge of C# is used as the output timing reference for first and third output data. The rising edge of C is used as the output reference for second and fourth output data. Ideally, C# is 180 degrees out of phase with C. When use of K and K# as the reference instead of C and C#, then fixed C and C# to HIGH. Operation cannot be guaranteed unless C and C# are fixed to HIGH (i.e. toggle of C and C#). Page 8 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B (2/2) Symbol Type Description CQ, CQ# Output Synchronous Echo Clock Outputs. The rising edges of these outputs are tightly matched to the synchronous data outputs and can be used as a data valid indication. These signals run freely and do not stop when Q tristates. If C and C# are stopped (if K and K# are stopped in the single clock mode), CQ and CQ# will also stop. Output Impedance Matching Input: This input is used to tune the device outputs to the system data bus impedance. Q, CQ and CQ# output impedance are set to 0.2 x RQ, where RQ is a resistor from this bump to ground. The output impedance can be minimized by directly connect ZQ to VDDQ. This pin cannot be connected directly to GND or left unconnected. The output impedance is adjusted every 20 s upon power-up to account for drifts in supply voltage and temperature. After replacement for a resistor, the new output impedance is reset by implementing power-on sequence. PLL Disable: When debugging the system or board, the operation can be performed at a clock frequency slower than TKHKH (MAX.) without the PLL circuit being used, if DLL# = LOW. The AC/DC characteristics cannot be guaranteed. For normal operation, DLL# must be HIGH and it can be connected to VDDQ through a 10 k or less resistor. IEEE 1149.1 Test Inputs: 1.8 V I/O level. These balls may be left Not Connected if the JTAG function is not used in the circuit. ZQ Input DLL# Input TMS TDI Input TCK Input IEEE 1149.1 Clock Input: 1.8 V I/O level. This pin must be tied to VSS if the JTAG function is not used in the circuit. TDO Output IEEE 1149.1 Test Output: 1.8 V I/O level. When providing any external voltage to TDO signal, it is recommended to pull up to VDD. VREF HSTL Input Reference Voltage: Nominally VDDQ/2. Provides a reference voltage for the input buffers. VDD Supply Power Supply: 1.8 V nominal. See Recommended DC Operating Conditions and DC Characteristics for range. VDDQ Supply Power Supply: Isolated Output Buffer Supply. Nominally 1.5 V. 1.8 V is also permissible. See Recommended DC Operating Conditions and DC Characteristics for range. VSS NC Supply Power Supply: Ground No Connect: These signals are not connected internally. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 9 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Block Diagram [PD44165084B] 19 ADDRESS R# ADDRESS W# 19 REGISTRY & LOGIC K W# MUX NW0# ARRAY 16 OUTPUT BUFFER MEMORY 32 OUTPUT SELECT 16 OUTPUT REGISTER & LOGIC 2 x 32 SENSE AMPS REGISTRY R# 19 WRITE DRIVER DATA 8 D0 to D7 WRITE REGISTER NW1# 8 16 16 Q0 to Q7 2 CQ, CQ# MUX K K K# K C, C# OR K, K# [PD44165094B] 19 ADDRESS R# ADDRESS W# 19 REGISTRY & LOGIC K W# MUX BW0# ARRAY 18 OUTPUT BUFFER MEMORY 36 OUTPUT SELECT 18 OUTPUT REGISTER & LOGIC 2 x 36 SENSE AMPS R# REGISTRY 19 WRITE DRIVER D0 to D8 WRITE REGISTER 9 DATA 9 18 18 Q0 to Q8 2 CQ, CQ# MUX K K# R10DS0018EJ0200 Rev.2.00 October 6, 2011 K K C, C# OR K, K# Page 10 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B [PD44165184B] 18 ADDRESS R# ADDRESS W# 18 REGISTRY & LOGIC K W# MUX BW0# 36 36 ARRAY 36 OUTPUT BUFFER 36 72 OUTPUT SELECT & LOGIC R# MEMORY 18 OUTPUT REGISTER REGISTRY 2 x 72 SENSE AMPS D0 to D17 DATA 18 WRITE DRIVER 18 WRITE REGISTER BW1# Q0 to Q17 2 CQ, CQ# MUX K K K# K C, C# OR K, K# [PD44165364B] 17 ADDRESS R# ADDRESS W# 17 REGISTRY & LOGIC K W# MUX ARRAY 72 OUTPUT BUFFER R# MEMORY 36 144 OUTPUT SELECT 72 2 x 144 SENSE AMPS & LOGIC 17 WRITE DRIVER REGISTRY WRITE REGISTER DATA 36 D0 to D35 72 72 OUTPUT REGISTER BW0# BW1# BW2# BW3# Q0 to Q35 2 CQ, CQ# MUX K K# R10DS0018EJ0200 Rev.2.00 October 6, 2011 K K C, C# OR K, K# Page 11 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Power-On Sequence in QDR II SRAM QDR II SRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. The following timing charts show the recommended power-on sequence. The following power-up supply voltage application is recommended: VSS, VDD, VDDQ, VREF, then VIN. VDD and VDDQ can be applied simultaneously, as long as VDDQ does not exceed VDD by more than 0.5 V during power-up. The following power-down supply voltage removal sequence is recommended: VIN, VREF, VDDQ, VDD, VSS. VDD and VDDQ can be removed simultaneously, as long as VDDQ does not exceed VDD by more than 0.5 V during power-down. Power-On Sequence Apply power and tie DLL# to HIGH. - Apply VDD before VDDQ. - Apply VDDQ before VREF or at the same time as VREF. Provide stable clock for more than 20 s to lock the PLL. PLL Constraints The PLL uses K clock as its synchronizing input and the input should have low phase jitter which is specified as TKC var. The PLL can cover 120 MHz as the lowest frequency. If the input clock is unstable and the PLL is enabled, then the PLL may lock onto an undesired clock frequency. Power-On Waveforms VDD/VDDQ VDD/VDDQ Stable (< 0.1 V DC per 50 ns) DLL# Fix HIGH (or tied to VDDQ) Clock Unstable Clock R10DS0018EJ0200 Rev.2.00 October 6, 2011 20 s or more Stable Clock Normal Operation Start Page 12 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Truth Table Operation WRITE cycle CLK R# W# LH H L D or Q Data in Load address, input write data on Input data DA(A+0) DA(A+1) DA(A+2) DA(A+3) consecutive K and K# rising edge Input clock K(t+1) K#(t+1) K(t+2) K#(t+2) READ cycle LH L x Data out Load address, read data on Output data QA(A+0) QA(A+1) QA(A+2) QA(A+3) consecutive C and C# rising edge Output clock C#(t+1) C(t+2) C#(t+2) C(t+3) NOP (No operation) Clock stop LH H H D = x, Q = High-Z Stopped x x Previous state Remarks 1. H : HIGH, L : LOW, x : don't care, : rising edge. 2. Data inputs are registered at K and K# rising edges. Data outputs are delivered at C and C# rising edges except if C and C# are HIGH then data outputs are delivered at K and K# rising edges. 3. All control inputs in the truth table must meet setup/hold times around the rising edge (LOW to HIGH) of K. All control inputs are registered during the rising edge of K. 4. This device contains circuitry that ensure the outputs to be in high impedance during power-up. 5. Refer to state diagram and timing diagrams for clarification. 6. It is recommended that K = K# = C = C# when clock is stopped. This is not essential but permits most rapid restart by overcoming transmission line charging symmetrically. 7. If R# was LOW to initiate the previous cycle, this signal becomes a don't care for this WRITE operation however it is strongly recommended that this signal is brought HIGH as shown in the truth table. 8. W# during write cycle and R# during read cycle were HIGH on previous K clock rising edge. Initiating consecutive READ or WRITE operations on consecutive K clock rising edges is not permitted. The device will ignore the second request. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 13 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Byte Write Operation [PD44165084B] Operation K# NW0# NW1# LH - 0 0 - LH 0 0 LH - 0 1 - LH 0 1 Write D4 to D7 LH - 1 0 - LH 1 0 Write nothing LH - 1 1 - LH 1 1 Write D0 to D7 Write D0 to D3 K Remarks 1. H : HIGH, L : LOW, : rising edge. 2. Assumes a WRITE cycle was initiated. NW0# and NW1# can be altered for any portion of the BURST WRITE operation provided that the setup and hold requirements are satisfied. [PD44165094B] Operation Write D0 to D8 Write nothing K K# BW0# LH - 0 - LH 0 LH - 1 - LH 1 Remarks 1. H : HIGH, L : LOW, : rising edge. 2. Assumes a WRITE cycle was initiated. BW0# can be altered for any portion of the BURST WRITE operation provided that the setup and hold requirements are satisfied. [PD44165184B] K K# BW0# BW1# Write D0 to D17 Operation LH - 0 0 - LH 0 0 Write D0 to D8 LH - 0 1 - LH 0 1 Write D9 to D17 LH - 1 0 - LH 1 0 LH - 1 1 - LH 1 1 Write nothing Remarks 1. H : HIGH, L : LOW, : rising edge. 2. Assumes a WRITE cycle was initiated. BW0# and BW1# can be altered for any portion of the BURST WRITE operation provided that the setup and hold requirements are satisfied. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 14 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B [PD44165364B] Operation K# BW0# BW1# BW2# BW3# LH - 0 0 0 0 - LH 0 0 0 0 LH - 0 1 1 1 - LH 0 1 1 1 Write D9 to D17 LH - 1 0 1 1 - LH 1 0 1 1 Write D18 to D26 LH - 1 1 0 1 - LH 1 1 0 1 Write D27 to D35 LH - 1 1 1 0 - LH 1 1 1 0 Write nothing LH - 1 1 1 1 - LH 1 1 1 1 Write D0 to D35 Write D0 to D8 K Remarks 1. H : HIGH, L : LOW, : rising edge. 2. Assumes a WRITE cycle was initiated. BW0# to BW3# can be altered for any portion of the BURST WRITE operation provided that the setup and hold requirements are satisfied. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 15 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Bus Cycle State Diagram LOAD NEW READ ADDRESS; R_Count = 0; R_Init = 1 LOAD NEW WRITE ADDRESS; W_Count = 0 Always W# = LOW & W_Count = 4 R# = LOW & R_Count = 4 WRITE DOUBLE; W_Count = W_Count+2 W# = LOW R_Init = 0 Always READ DOUBLE; R_Count = R_Count+2 R# = HIGH & R_Count = 4 W_Count = 2 Always R_Count = 2 Always R# = LOW INCREMENT WRITE ADDRESS BY TWO W# = HIGH & W_Count = 4 INCREMENT READ ADDRESS BY TWO R_Init = 0 R# = HIGH W# = HIGH WRITE PORT NOP Power UP Supply voltage provided Supply voltage provided READ PORT NOP R_Init = 0 Remarks 1. The address is concatenated with two additional internal LSBs to facilitate burst operation. The address order is always fixed as: xxx...xxx+0, xxx...xxx+1, xxx...xxx+2, xxx...xxx+3. Bus cycle is terminated at the end of this sequence (burst count = 4). 2. Read and write state machines can be active simultaneously. Read and write cannot be simultaneously initiated. Read takes precedence. 3. State machine control timing is controlled by K. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 16 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Electrical Characteristics Absolute Maximum Ratings Parameter Rating Unit VDD -0.5 to +2.5 V VDDQ -0.5 to VDD V Input voltage VIN -0.5 to VDD+0.5 (2.5 V MAX.) V Input / Output voltage VI/O -0.5 to VDDQ+0.5 (2.5 V MAX.) V Operating ambient temperature TA 0 to 70 C Supply voltage Output supply voltage Symbol Conditions (E** series) -40 to 85 (E**Y series) Storage temperature -55 to +125 Tstg C Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Recommended DC Operating Conditions (TA = 0 to 70C, TA = -40 to 85C) Parameter MIN. TYP. MAX. Unit VDD 1.7 1.8 1.9 V Output supply voltage VDDQ 1.4 VDD V 1 Input HIGH voltage VIH (DC) VREF +0.1 VDDQ+0.3 V 1, 2 Input LOW voltage VIL (DC) -0.3 VREF -0.1 V 1, 2 Clock input voltage VIN -0.3 VDDQ+0.3 V 1, 2 Reference voltage VREF 0.68 0.95 V Supply voltage Symbol Conditions Note Notes 1. During normal operation, VDDQ must not exceed VDD. 2. Power-up: VIH VDDQ +0.3 V and VDD 1.7 V and VDDQ 1.4 V for t 200 ms Recommended AC Operating Conditions (TA = 0 to 70C, TA = -40 to 85) Parameter Symbol Input HIGH voltage VIH (AC) Input LOW voltage VIL (AC) Conditions MIN. MAX. VREF +0.2 VREF -0.2 Unit Note V 1 V 1 Note 1. Overshoot: VIH (AC) VDD +0.7 V (2.5 V MAX.) for t TKHKH/2 Undershoot: VIL (AC) -0.5 V for t TKHKH/2 Control input signals may not have pulse widths less than TKHKL (MIN.) or operate at cycle rates less than TKHKH (MIN.). R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 17 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B DC Characteristics 1 (TA = 0 to 70C, VDD = 1.8 0.1 V) Parameter Symbol Test condition MIN. MAX. X8 Input leakage current ILI I/O leakage current ILO Operating supply current IDD (Read cycle / Write cycle) Standby supply current ISB1 (NOP) Output HIGH voltage Output LOW voltage Notes 1. 2. 3. 4. x36 -2 +2 A -2 +2 A -E33 520 520 580 740 II/O = 0 mA, -E35 500 500 560 710 Cycle = MAX. -E40 460 460 520 650 -E50 410 410 460 570 VIN VIL or VIN VIH, -E33 390 390 400 430 II/O = 0 mA, -E35 390 390 390 420 Cycle = MAX. -E40 370 370 380 400 Inputs static -E50 350 350 350 370 Note1 VOL(Low) IOL 0.1 mA VOL x18 VIN VIL or VIN VIH, VOH(Low) |IOH| 0.1 mA VOH X9 Unit Note Note2 mA mA VDDQ-0.2 VDDQ V 3, 4 VDDQ/2-0.12 VDDQ/2+0.12 V 3, 4 VSS 0.2 V 3, 4 VDDQ/2-0.12 VDDQ/2+0.12 V 3, 4 Outputs are impedance-controlled. | IOH | = (VDDQ/2)/(RQ/5) 15% for values of 175 RQ 350 . Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) 15% for values of 175 RQ 350 . AC load current is higher than the shown DC values. HSTL outputs meet JEDEC HSTL Class I standards. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 18 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B DC Characteristics 2 (TA = -40 to 85C, VDD = 1.8 0.1 V) Parameter Symbol Test condition MIN. MAX. X8 Input leakage current ILI I/O leakage current ILO Operating supply current IDD (Read cycle / Write cycle) Standby supply current ISB1 (NOP) Output HIGH voltage Output LOW voltage Notes 1. 2. 3. 4. x36 -2 +2 A -2 +2 A -E33Y 640 640 710 870 II/O = 0 mA, -E35Y 620 620 690 840 Cycle = MAX. -E40Y 580 580 650 780 -E50Y 530 530 590 700 VIN VIL or VIN VIH, -E33Y 510 510 520 550 II/O = 0 mA, -E35Y 510 510 510 540 Cycle = MAX. -E40Y 490 490 500 520 Inputs static -E50Y 470 470 470 490 Note1 VOL(Low) IOL 0.1 mA VOL x18 VIN VIL or VIN VIH, VOH(Low) |IOH| 0.1 mA VOH X9 Unit Note Note2 mA mA VDDQ-0.2 VDDQ V 3, 4 VDDQ/2-0.12 VDDQ/2+0.12 V 3, 4 VSS 0.2 V 3, 4 VDDQ/2-0.12 VDDQ/2+0.12 V 3, 4 Outputs are impedance-controlled. | IOH | = (VDDQ/2)/(RQ/5) 15% for values of 175 RQ 350 . Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) 15% for values of 175 RQ 350 . AC load current is higher than the shown DC values. HSTL outputs meet JEDEC HSTL Class I standards. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 19 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Capacitance (TA = 25C, f = 1 MHz) Parameter Symbol Input capacitance (Address, Control) CIN Input / Output capacitance Test conditions MIN. MAX. Unit VIN = 0 V 5 pF CI/O VI/O = 0 V 7 pF Cclk Vclk = 0 V 6 pF (D, Q, CQ, CQ#) Clock Input capacitance Remark These parameters are periodically sampled and not 100% tested. Thermal Characteristics Parameter Thermal resistance Symbol ja Substrate 4-layer from junction to ambient air 8-layer Thermal characterization parameter jt 4-layer from junction to the top center of the package surface Thermal resistance 8-layer jc Airflow TYP. Unit 0 m/s 21.4 C/W 1 m/s 13.6 C/W 0 m/s 20.3 C/W 1 m/s 13.1 C/W 0 m/s 0.02 C/W 1 m/s 0.06 C/W 0 m/s 0.02 C/W 1 m/s 0.06 C/W 2.65 C/W from junction to case R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 20 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B AC Characteristics (TA = 0 to 70C or TA = -40 to 85C,) AC Test Conditions (VDD = 1.8 0.1 V, VDDQ = 1.4 V to VDD) Input waveform (Rise / Fall time 0.3 ns) 1.25 V 0.75 V Test Points 0.75 V 0.25 V Output waveform Test Points VDDQ / 2 VDDQ / 2 Output load condition Figure 1. External load at test VDDQ / 2 0.75 V 50 VREF ZO = 50 SRAM 250 ZQ R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 21 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Read and Write Cycle Parameter Symbol -E33, E33Y (300 MHz) -E35, E35Y (287 MHz) -E40, E40Y (250 MHz) -E50, E50Y (200 MHz) MIN. MAX. MIN. MAX. MIN. MAX. MIN. Unit Note 8.4 ns 1 0.2 2 MAX. Clock Average Clock cycle time (K, K#, C, C#) Clock phase jitter (K, K#, C, C#) Clock HIGH time (K, K#, C, C#) Clock LOW time (K, K#, C, C#) Clock HIGH to Clock# HIGH (K K#, C C#) Clock# HIGH to Clock HIGH (K# K, C# C) Clock to data clock (K C, K# C#) PLL lock time (K, C) K static to PLL reset TKHKH 3.3 8.4 3.5 0.2 8.4 4.0 5.0 TKC var TKHKL TKLKH TKHK#H 1.32 1.32 1.49 1.5 1.5 1.7 1.6 1.6 1.8 2.0 2.0 2.2 ns ns ns ns TK#HKH 1.49 1.7 1.8 2.2 ns TKHCH 0 TKC lock TKC reset 20 30 1.45 0.2 8.4 0 1.65 0.2 0 1.8 0 2.3 ns 20 30 20 30 20 30 s ns 3 4 TCQHCQ#H 1.24 1.35 1.55 1.95 ns 5 TCQ#HCQH 1.24 1.35 1.55 1.95 ns 5 Output Times CQ HIGH to CQ# HIGH (CQ CQ#) CQ# HIGH to CQ HIGH (CQ# CQ) C, C# HIGH to output valid C, C# HIGH to output hold C, C# HIGH to echo clock valid C, C# HIGH to echo clock hold CQ, CQ# HIGH to output valid CQ, CQ# HIGH to output hold C HIGH to output High-Z C HIGH to output Low-Z TCHQV TCHQX TCHCQV TCHCQX TCQHQV TCQHQX TCHQZ TCHQX1 0.45 -0.45 -0.45 -0.45 -0.45 ns ns ns ns ns ns ns ns TAVKH TIVKH 0.4 0.4 0.5 0.5 0.5 0.5 0.6 0.6 ns ns 7 7 TDVKH 0.3 0.35 0.35 0.4 ns 7 TKHAX TKHIX 0.4 0.4 0.5 0.5 0.5 0.5 0.6 0.6 ns ns 7 7 TKHDX 0.3 0.35 0.35 0.4 ns 7 -0.45 0.45 -0.45 0.45 -0.45 0.45 -0.45 0.27 -0.27 0.45 -0.45 0.45 -0.45 0.3 -0.3 0.45 0.45 -0.45 0.45 -0.45 0.3 -0.3 0.45 0.35 -0.35 0.45 0.45 6 6 Setup Times Address valid to K rising edge Control inputs (R#, W#) valid to K rising edge Data inputs and write data select inputs (BWx#, NWx#) valid to K, K# rising edge Hold Times K rising edge to address hold K rising edge to control inputs (R#, W#) hold K, K# rising edge to data inputs and write data select inputs (BWx#, NWx#) hold R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 22 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Notes 1. When debugging the system or board, these products can operate at a clock frequency slower than TKHKH (MAX.) without the PLL circuit being used, if DLL# = LOW. Read latency (RL) is changed to 1.0 clock cycle in this operation. The AC/DC characteristics cannot be guaranteed, however. 2. Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge. TKC var (MAX.) indicates a peak-to-peak value. 3. VDD slew rate must be less than 0.1 V DC per 50 ns for PLL lock retention. PLL lock time begins once VDD and input clock are stable. It is recommended that the device is kept NOP (LD# = HIGH) during these cycles. 4. K input is monitored for this operation. See below for the timing. K or TKC reset K TKC reset 5. Guaranteed by design. 6. Echo clock is very tightly controlled to data valid / data hold. By design, there is a 0.1 ns variation from echo clock to data. The data sheet parameters reflect tester guardbands and test setup variations. 7. This is a synchronous device. All addresses, data and control lines must meet the specified setup and hold times for all latching clock edges. Remarks 1. This parameter is sampled. 2. Test conditions as specified with the output loading as shown in AC Test Conditions unless otherwise noted. 3. Control input signals may not be operated with pulse widths less than TKHKL (MIN.). 4. If C, C# are tied HIGH, K, K# become the references for C, C# timing parameters. 5. VDDQ is 1.5 V DC. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 23 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Read and Write Timing 1 2 WRITE READ WRITE READ NOP 3 4 5 NOP 6 7 K TKHKL TKLKH TKHKH TKHK#H TK#HKH K# R# TKHIX TIVKH TKHIX TIVKH W# A0 Address A2 A1 TDVKH TAVKH TKHAX Data in Data out Qx2 Qx3 TCHQX1 A3 TKHDX TDVKH TKHDX D10 D11 D12 D13 D30 D31 Q00 Q01 Q02 Q03 Q20 Q21 TCHQX D32 D33 Q22 Q23 TCQHQX TCHQX TCHQZ TCHQV TCQHQV TCHQV CQ TCHCQX TCHCQV TCQHCQ#H TCQ#HCQH CQ# TKHCH TCHCQX TCHCQV C TKHKL TKLKH TKHKH TKHK#H TK#HKH TKHCH C# Remarks 1. Q00 refers to output from address A0+0. Q01 refers to output from the next internal burst address following A0,i.e.,A0+1. 2. Outputs are disabled (high impedance) 3.5 clock cycles after the last READ (R# = LOW) is input in the sequences of [READ]-[NOP]-[NOP], [READ]-[WRITE]-[NOP] and [READ]-[NOP]-[WRITE]. 3. In this example, if address A2 = A1, data Q20 = D10, Q21 = D11, Q22 = D12 and Q23 = D13. Write data is forwarded immediately as read results. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 24 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Application Example SRAM#1 D Vt SRAM Controller A R# ZQ CQ# CQ Q R= 250 D ZQ CQ# CQ Q A R# W# BWx# C/C# K/K# ... SRAM#4 W# BWx# C/C# K/K# R= 250 R Data In Data Out R Address Vt R R# Vt W# BW# ... SRAM#1 CQ/CQ# SRAM#4 CQ/CQ# Vt R Vt R Source CLK/CLK# Return CLK/CLK# Vt R R = 50 Vt = Vref Remark AC Characteristics are defined at the condition of SRAM outputs, CQ, CQ# and Q with termination. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 25 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B JTAG Specification These products support a limited set of JTAG functions as in IEEE standard 1149.1. Test Access Port (TAP) Pins Pin name Pin assignments Description TCK 2R Test Clock Input. All input are captured on the rising edge of TCK and all outputs propagate from the falling edge of TCK. TMS 10R Test Mode Select. This is the command input for the TAP controller state machine. TDI 11R Test Data Input. This is the input side of the serial registers placed between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP controller state machine and the instruction that is currently loaded in the TAP instruction. TDO 1R Test Data Output. This is the output side of the serial registers placed between TDI and TDO. Output changes in response to the falling edge of TCK. Remark The device does not have TRST (TAP reset). The Test-Logic Reset state is entered while TMS is held HIGH for five rising edges of TCK. The TAP controller state is also reset on the SRAM POWER-UP. JTAG DC Characteristics (TA = 0 to 70C, VDD = 1.8 0.1 V, unless otherwise noted) Parameter Symbol Conditions MIN. MAX. Unit JTAG Input leakage current ILI 0 V VIN VDD -5.0 +5.0 A JTAG I/O leakage current ILO 0 V VIN VDDQ, -5.0 +5.0 A JTAG input HIGH voltage VIH 1.3 VDD+0.3 V JTAG input LOW voltage VIL -0.3 +0.5 V Outputs disabled JTAG output HIGH voltage JTAG output LOW voltage R10DS0018EJ0200 Rev.2.00 October 6, 2011 VOH1 | IOHC | = 100 A 1.6 V VOH2 | IOHT | = 2 mA 1.4 V VOL1 IOLC = 100 A 0.2 V VOL2 IOLT = 2 mA 0.4 V Page 26 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B JTAG AC Test Conditions Input waveform (Rise / Fall time 1 ns) 1.8 V 0.9 V Test Points 0.9 V 0.9 V Test Points 0.9 V 0V Output waveform Output load Figure 2. External load at test VTT = 0.9 V 50 ZO = 50 TDO 20 pF R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 27 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B JTAG AC Characteristics (TA = 0 to 70C) Parameter Symbol Conditions MIN. MAX. Unit Clock Clock cycle time tTHTH 50 ns Clock frequency fTF Clock HIGH time tTHTL 20 ns Clock LOW time tTLTH 20 ns TCK LOW to TDO unknown tTLOX 0 TCK LOW to TDO valid tTLOV 20 MHz Output time ns 10 ns Setup time TMS setup time tMVTH 5 ns TDI valid to TCK HIGH tDVTH 5 ns tCS 5 ns TMS hold time tTHMX 5 ns TCK HIGH to TDI invalid tTHDX 5 ns tCH 5 ns Capture setup time Hold time Capture hold time JTAG Timing Diagram tTHTH TCK tMVTH tTHTL tTLTH TMS tTHMX tDVTH TDI tTHDX tTLOX tTLOV TDO R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 28 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Scan Register Definition (1) Register name Description Instruction register The instruction register holds the instructions that are executed by the TAP controller when it is moved into the run-test/idle or the various data register state. The register can be loaded when it is placed between the TDI and TDO pins. The instruction register is automatically preloaded with the IDCODE instruction at power-up whenever the controller is placed in test-logic-reset state. Bypass register The bypass register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through the RAMs TAP to another device in the scan chain with as little delay as possible. ID register The ID Register is a 32 bit register that is loaded with a device and vendor specific 32 bit code when the controller is put in capture-DR state with the IDCODE command loaded in the instruction register. The register is then placed between the TDI and TDO pins when the controller is moved into shift-DR state. Boundary register The boundary register, under the control of the TAP controller, is loaded with the contents of the RAMs I/O ring when the controller is in capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to shift-DR state. Several TAP instructions can be used to activate the boundary register. The Scan Exit Order tables describe which device bump connects to each boundary register location. The first column defines the bit's position in the boundary register. The second column is the name of the input or I/O at the bump and the third column is the bump number. Scan Register Definition (2) Register name Bit size Unit Instruction register 3 bit Bypass register 1 bit ID register 32 bit Boundary register 107 bit ID Register Definition Part number Organization ID [31:28] vendor revision no. ID [27:12] part no. PD44165084B 2M x 8 XXXX 0000 0000 0000 1111 00000010000 1 PD44165094B 2M x 9 XXXX 0000 0000 0101 0010 00000010000 1 PD44165184B 1M x 18 XXXX 0000 0000 0001 0000 00000010000 1 PD44165364B 512K x 36 XXXX 0000 0000 0001 0001 00000010000 1 R10DS0018EJ0200 Rev.2.00 October 6, 2011 ID [11:1] vendor ID no. ID [0] fix bit Page 29 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B SCAN Exit Order Bit no. Signal name x8 x9 x18 x36 Bump Bit Signal name ID no. x8 x9 x18 Bump Bit Signal name Bump x36 ID no. x8 x9 x18 x36 ID 1 C# 6R 37 NC NC NC D15 10D 73 NC NC NC Q28 2C 2 C 6P 38 NC NC NC Q15 9E 74 Q4 Q5 Q11 Q20 3E 3 A 6N 39 NC NC Q7 Q7 10C 75 D4 D5 D11 D20 2D 4 A 7P 40 NC NC D7 D7 11D 76 NC NC NC D29 2E 5 A 7N 41 NC NC NC D16 9C 77 NC NC NC Q29 1E 6 A 7R 42 NC NC NC Q16 9D 78 NC NC Q12 Q21 2F 7 A 8R 43 Q3 Q4 Q8 Q8 11B 79 NC NC D12 D21 3F 8 A 8P 44 D3 D4 D8 D8 11C 80 NC NC NC D30 1G 9 A 9R 45 NC NC NC D17 9B 81 NC NC NC Q30 1F NC NC NC Q17 10B 82 Q5 Q6 Q13 Q22 3G 10 NC Q0 Q0 Q0 11P 46 11 NC D0 D0 D0 10P 47 CQ 11A 83 D5 D6 D13 D22 2G 12 NC NC NC D9 10N 48 - Interna 84 NC NC NC D31 1J 13 NC NC NC Q9 9P 49 9A 85 NC NC NC Q31 2J 14 NC NC Q1 Q1 10M 50 A 8B 86 NC NC Q14 Q23 3K 15 NC NC D1 D1 11N 51 A 7C 87 NC NC D14 D23 3J 16 NC NC NC D10 9M 52 NC 6C 88 NC NC NC D32 2K 17 NC NC NC Q10 9N 53 R# 8A 89 NC NC NC Q32 1K 18 Q0 Q1 Q2 Q2 11L 54 NC BW1 7A 90 Q6 Q7 Q15 Q24 2L 19 D0 D1 D2 D2 11M 55 NW0 BW0 BW0 BW0 7B 91 D6 D7 D15 D24 3L 20 NC NC NC D11 9L 56 K 6B 92 NC NC NC D33 1M 21 NC NC NC Q11 10L 57 K# 6A 93 NC NC NC Q33 1L 22 NC NC Q3 Q3 11K 58 NC BW3 5B 94 NC NC Q16 Q25 3N 23 NC NC D3 D3 10K 59 NW1 NC BW1 BW2 5A 95 NC NC D16 D25 3M 24 NC NC NC D12 9J 60 W# 4A 96 NC NC NC D34 1N 25 NC NC NC Q12 9K 61 A 5C 97 NC NC NC Q34 2M 26 Q1 Q2 Q4 Q4 10J 62 A 4B 98 Q7 Q8 Q17 Q26 3P 27 D1 D2 D4 D4 11J 63 3A 99 D7 D8 D17 D26 2N 11H 64 DLL# 1H 100 NC NC NC D35 2P CQ# 1A 101 NC NC NC Q35 1P 28 ZQ A NC NC A A A NC NC A NC NC NC 29 NC NC NC D13 10G 65 30 NC NC NC Q13 9G 66 NC NC Q9 Q18 2B 102 A 3R 31 NC NC Q5 Q5 11F 67 NC NC D9 D18 3B 103 A 4R 32 NC NC D5 D5 11G 68 NC NC NC D27 1C 104 A 4P 33 NC NC NC D14 9F 69 NC NC NC Q27 1B 105 A 5P 34 NC NC NC Q14 10F 70 NC NC Q10 Q19 3D 106 A 5N 35 Q2 Q3 Q6 Q6 11E 71 NC NC D10 D19 3C 107 A 5R 36 D2 D3 D6 D6 10E 72 NC NC NC 1D R10DS0018EJ0200 Rev.2.00 October 6, 2011 D28 Page 30 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B JTAG Instructions Instructions Description EXTEST The EXTEST instruction allows circuitry external to the component package to be tested. Boundary-scan register cells at output pins are used to apply test vectors, while those at input pins capture test results. Typically, the first test vector to be applied using the EXTEST instruction will be shifted into the boundary scan register using the PRELOAD instruction. Thus, during the update-IR state of EXTEST, the output drive is turned on and the PRELOAD data is driven onto the output pins. IDCODE The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in capture-DR mode and places the ID register between the TDI and TDO pins in shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up and any time the controller is placed in the test-logic-reset state. BYPASS When the BYPASS instruction is loaded in the instruction register, the bypass register is placed between TDI and TDO. This occurs when the TAP controller is moved to the shiftDR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path. SAMPLE / PRELOAD SAMPLE / PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is loaded in the instruction register, moving the TAP controller into the capture-DR state loads the data in the RAMs input and Q pins into the boundary scan register. Because the RAM clock(s) are independent from the TAP clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input buffers are in transition (i.e., in a metastable state). Although allowing the TAP to sample metastable input will not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the TAPs input data capture setup plus hold time (tCS plus tCH). The RAMs clock inputs need not be paused for any other TAP operation except capturing the I/O ring contents into the boundary scan register. Moving the controller to shift-DR state then places the boundary scan register between the TDI and TDO pins. SAMPLE-Z If the SAMPLE-Z instruction is loaded in the instruction register, all RAM Q pins are forced to an inactive drive state (high impedance) and the boundary register is connected between TDI and TDO when the TAP controller is moved to the shift-DR state. JTAG Instruction Coding IR2 IR1 IR0 Instruction 0 0 0 EXTEST Note 0 0 1 IDCODE 0 1 0 SAMPLE-Z 1 0 1 1 RESERVED 2 1 0 0 SAMPLE / PRELOAD 1 0 1 RESERVED 2 1 1 0 RESERVED 2 1 1 1 BYPASS Notes 1. TRISTATE all Q pins and CAPTURE the pad values into a SERIAL SCAN LATCH. 2. Do not use this instruction code because the vendor uses it to evaluate this product. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 31 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Output Pin States of CQ, CQ# and Q Instructions Control-Register Status Output Pin Status CQ,CQ# Q 0 Update High-Z 1 Update Update 0 SRAM SRAM 1 SRAM SRAM SAMPLE-Z 0 High-Z High-Z 1 High-Z High-Z SAMPLE 0 SRAM SRAM 1 SRAM SRAM 0 SRAM SRAM 1 SRAM SRAM EXTEST IDCODE BYPASS Remark The output pin statuses during each instruction vary according to the Control-Register status (value of Boundary Scan Boundary Scan Register Register, bit no. 107). CAPTURE Register There are three statuses: Update : Contents of the "Update Register" are output to the SRAM Output Update Register output pin (QDR Pad). SRAM : Contents of the SRAM internal output "SRAM Output" are output to the output pin (QDR Pad). Update High-Z :The output pin (QDR Pad) becomes high impedance by controlling of the "High-Z JTAG ctrl". The Control-Register status is set during Update-DR at the QDR Pad SRAM High-Z SRAM Output Driver EXTEST or SAMPLE instruction. High-Z JTAG ctrl R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 32 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Boundary Scan Register Status of Output Pins CQ, CQ# and Q Instructions SRAM Status Boundary Scan Register Status CQ,CQ# Q READ (Low-Z) Pad Pad NOP (High-Z) Pad Pad READ (Low-Z) - - NOP (High-Z) - - SAMPLE-Z READ (Low-Z) Pad Pad NOP (High-Z) Pad Pad SAMPLE READ (Low-Z) Internal Internal NOP (High-Z) Internal Pad READ (Low-Z) - - NOP (High-Z) - - EXTEST IDCODE BYPASS Remark The Boundary Scan Register statuses during execution each Note No definition No definition Boundary Scan Register instruction vary according to the instruction code and SRAM operation mode. CAPTURE Register There are two statuses: Internal Pad : Contents of the output pin (QDR Pad) are captured in the "CAPTURE Register" in the Boundary Scan Update Register Pad SRAM Output Register. Internal : Contents of the SRAM internal output "SRAM Output" are captured in the "CAPTURE Register" in the Boundary Scan Register. QDR Pad SRAM Output Driver High-Z JTAG ctrl R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 33 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B TAP Controller State Diagram 1 Test-Logic-Reset 0 1 0 1 1 Select-IR-Scan Select-DR-Scan Run-Test / Idle 0 0 1 1 Capture-IR Capture-DR 0 0 0 Shift-DR 0 Shift-IR 1 1 1 1 Exit1-DR Exit1-IR 0 0 0 Pause-DR 0 Pause-IR 1 1 0 0 Exit2-DR Exit2-IR 1 1 Update-DR 1 Update-IR 0 1 0 Disabling the Test Access Port It is possible to use this device without utilizing the TAP. To disable the TAP Controller without interfering with normal operation of the device, TCK must be tied to VSS to preclude mid level inputs. TDI and TMS may be left open but fix them to VDD via a resistor of about 1 k when the TAP controller is not used. TDO should be left unconnected also when the TAP controller is not used. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 34 of 39 New Instruction PD44165084B, PD44165094B , PD44165184B, PD44165364B Run-Test/Idle Update-IR Exit1-IR Shift-IR Exit2-IR IDCODE Pause-IR Exit1-IR Shift-IR R10DS0018EJ0200 Rev.2.00 October 6, 2011 Select-IR-Scan Run-Test/Idle Instruction Register state TDI Controller state TMS Test-Logic-Reset TDO Output Inactive Select-DR-Scan TCK Test Logic Operation (Instruction Scan) Capture-IR Page 35 of 39 IDCODE PD44165084B, PD44165094B , PD44165184B, PD44165364B Test-Logic-Reset Select-IR-Scan Select-DR-Scan Run-Test/Idle Update-DR Exit1-DR Shift-DR Instruction Exit2-DR Pause-DR Exit1-DR Shift-DR Capture-DR R10DS0018EJ0200 Rev.2.00 October 6, 2011 Instruction Register state TDI Controller state TMS TCK Test Logic (Data Scan) Run-Test/Idle TDO Output Inactive Select-DR-Scan Page 36 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Package Dimensions 165-PIN PLASTIC BGA(13x15) ZD w S B E ZE B 11 10 9 8 7 6 5 4 3 2 1 A D R P N M L K J H G F E D C B A w S A INDEX MARK A y1 (UNIT:mm) A2 S S y e S b x A1 M S AB ITEM D DIMENSIONS 13.000.10 E 15.000.10 w 0.30 A 1.350.11 A1 0.370.05 A2 0.98 e 1.00 b +0.10 0.50 -0.05 x 0.10 y 0.15 y1 0.25 ZD 1.50 ZE 0.50 P165F5-100-EQ3 R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 37 of 39 PD44165084B, PD44165094B , PD44165184B, PD44165364B Recommended Soldering Condition Please consult with our sales offices for soldering conditions of these products. Types of Surface Mount Devices PD44165084BF5-EQ3 : 165-pin PLASTIC BGA (13 x 15) PD44165094BF5-EQ3 : 165-pin PLASTIC BGA (13 x 15) PD44165184BF5-EQ3 : 165-pin PLASTIC BGA (13 x 15) PD44165364BF5-EQ3 : 165-pin PLASTIC BGA (13 x 15) Quality Grade * A quality grade of the products is "Standard". * Anti-radioactive design is not implemented in the products. * Semiconductor devices have the possibility of unexpected defects by affection of cosmic ray that reach to the ground and so forth. R10DS0018EJ0200 Rev.2.00 October 6, 2011 Page 38 of 39 Revision History Rev. Date 1st edition Rev.0.02 '10.02.01 '10.08.18 Rev.1.00 '10.12.13 Rev.2.00 '11.10.06 PD44165084B, PD44165094B, PD44165184B, PD44165364B Description Page P17 P18 P34 Throughout Throughout Summary New Preliminary Data Sheet DC Characteristics (Modification, Spec of IDD and ISB1) Thermal Characteristics (Modification, Spec) Package Dimensions (Modification, Dimensions) Preliminary Data Sheet AE Data Sheet Add Lead and the extended temperature operation product All trademarks and registered trademarks are the property of their respective owners. C - 39 Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-585-100, Fax: +44-1628-585-900 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 7F, No. 363 Fu Shing North Road Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632 Tel: +65-6213-0200, Fax: +65-6278-8001 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 (c) 2011 Renesas Electronics Corporation. All rights reserved. Colophon 1.0