A Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Angle of Throw: Materials & Finishes Bushing: Housing: Mounting Bracket: Movable Contacts: Stationary Contacts: Lamp Contacts: Base: Switch Terminals: Lamp Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Tilt Tactiles Slides Rotaries Keylocks Other Ratings Installation Touch Mounting Torque: Soldering Time & Temp: Cleaning: Standards & Certifications Flammability Standards: UL: Accessories Indicators LED Tipped Toggles General Specifications Pushbuttons Rockers Toggles Series M2100 Supplement CSA: A80 6A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum On-to-On Position Off-to-On Position Single Pole 3.19N 3.92N Double Pole 4.41N 7.06N 20 Brass with nickel plating Stainless steel Steel with tin plating Silver alloy or silver alloy with gold plating Silver with silver plating or copper or brass with gold plating Phosphor bronze Diallyl phthalate (UL94V-0) Copper with silver or gold plating Brass with silver or gold plating -10C through +55C (+14F through +131F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 1.47Nm (13 lb*in) for double nut; .67Nm (6 lb*in) for single nut Wave Soldering (PC version): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Note: Lever must be in center position while soldering. PC mountable device is not process sealed. Hand clean locally using alcohol based solution. UL94V-0 base File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" to end of part number to order UL recognized switch. Single pole with synchronous circuits & single color LEDs & solder lug or PC recognized at 6A @ 125V AC. File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" to end of part number to order CSA certified switch. All single pole with synchronous circuits & single color LEDs certified at 6A @ 125V AC. www.nkkswitches.com 3/13/17 A Rockers Distinctive Characteristics Toggles Series M2100 LED Tipped Toggles Pushbuttons Industry's first LED illumination at tip of toggle switches. Programmable Illuminated PB Single color LEDs of red, yellow, and green, plus bicolor red/green, to meet varied design requirements. LEDs can operate independently from or synchronously with switching operation. Antijamming feature to protect contacts from damage due to excessive downward force on the toggle. Keylocks High torque bushing prevents the bushing from rotating or separating from the metal frame during installation. Rotaries Stainless steel frame resists corrosion. Slides Silver contacts are of specially composed alloy for hardness. High insulating barriers protect against crossover in double pole devices. Tactiles Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Tilt 1,500V dielectric strength between switch contacts and case is accomplished by clinching the frame away from the terminals. Supplement Accessories Indicators Touch Actual Size www.nkkswitches.com A81 A LED Tipped Toggles TYPICAL SWITCH ORDERING EXAMPLE M21 Pushbuttons Rockers Toggles Series M2100 1 2 Programmable Illuminated PB Poles 1 SPDT *2 DPDT T L Isolated T Synchronous Circuits W Contact Materials & Ratings LED Circuits & Actuator Types * Available only with Terminals 01, 02, 03 Keylocks C W Silver; Rated 6A @ 125V AC G Gold; Rated 0.4VA max @ 28V AC/DC max LED Colors 2 ON NONE ON 3 ON OFF ON Single Color Rotaries 6mm Thread (Metric) 01 Solder Lug with Threaded Bushing 02 Quick Connect with Threaded Bushing E Yellow 03 Straight PC with Threaded Bushing F Green 30 Right Angle PC with Smooth Bushing (available with gold contacts only) Slides Red/Green Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Tilt Tactiles /M 1/4-40 Thread (Inch) Terminals & Mounting Types IMPORTANT: DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch M2112TCW01 Red LED Synchronous LED Circuit in Actuator Indicators No Code Red CF SPDT ON-NONE-ON Switch Circuit Accessories Threaded Bushings C Bicolor Supplement Silver Contacts with 6-Amp Rating A82 01 www.nkkswitches.com 1/4-40 Threaded Bushing Solder Lug Terminals A POLES & CIRCUITS & LED ILLUMINATION Toggle Position & Terminal Numbers ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 5-6 NONE NONE Green 5-4 ON 2-3 OFF OPEN ON 2-1 SPDT LED Circuit Isolated LEDs (see schematics) Connected LED Terminals ON 4-6 ON 4-6 ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 OFF OPEN ON 4-6 Synchronous Bicolor LED Connected LED Terminals Red 5-6 OFF OPEN Green 5-4 ON 2-3 5-6 NONE NONE ON 2-1 5-4 Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 NONE NONE ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 8-9 NONE NONE Green 8-7 ON 2-3 5-6 OFF OPEN ON 2-1 5-4 M2122 DPDT LED Circuit Connected Power Terminals M2123 DPDT LED Circuit Connected Power Terminals Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 ON 7-9 ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 OFF OPEN ON 7-9 Synchronous Bicolor LED Connected LED Terminals Red 8-9 OFF OPEN Green 8-7 L(+) 3 1 L(-) 4 6 2 (COM) Red Green Isolated Bicolor LED 3 1 6 COM (+) Red 4 ( ) Green 2 (COM) Synchronous Single Color LED L(+) 3 1 L(-) 4 6 2 (COM) Synchronous Bicolor LED Red Green 3 1 6 5 COM (+) 4 External Connection Isolated Single Color LED 2 (COM) 5 L(+) 3 1 6 4 2 (COM) Isolated Bicolor LED Synchronous Single Color LED 3 5 1 3 1 4 9 COM (+) Red 7 ( ) Green 5 6 2 (COM) Synchronous Bicolor LED 9 Red Green 6 2 (COM) L(-) 7 4 7 L(+) 5 9 L(-) Red Green 3 1 6 4 9 8 COM (+) 7 External Connection Supplement LED Circuit M2113 Connected Power Terminals Rockers NONE NONE Pushbuttons ON 4-6 Programmable Illuminated PB Isolated LEDs (see schematics) Connected LED Terminals 2 (COM) Isolated Single Color LED Keylocks ON 2-1 SPDT Rotaries NONE NONE M2112 Connected Power Terminals Slides ON 2-3 Keyway Notes: Terminal numbers are not actually on the switch. LEDs require an external power source. Tactiles Up Tilt Center Touch Down Indicators Pole & Throw Accessories Model Schematics Toggles Series M2100 LED Tipped Toggles www.nkkswitches.com A83 A The electrical specifications shown are determined at a basic temperature of 25C. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in Supplement Section. Single Color Bicolor C E F CF Color Red Yellow Green Red/Green Units Programmable Illuminated PB The LED is an integral part of the switch and not available separately. Maximum Forward Current I FM 30 30 30 25 mA Typical Forward Current IF 20 20 20 10 mA Forward Voltage VF 2.2 2.1 2.2 1.7/2.0 V Maximum Reverse Voltage VRM 4 4 4 --- V Current Reduction Rate Above 25C I F 0.38 0.38 0.38 0.33/0.33 mA/C Keylocks Pushbuttons LED Tipped Toggles LED COLORS & SPECIFICATIONS Rockers Toggles Series M2100 Ambient Temperature Range Bicolor LED is translucent white when unlit. -10 ~ +55C Rotaries LED CIRCUIT, TOGGLE, & MOUNTING TYPE COMBINATIONS L Toggle with Isolated LED Circuit Slides T Toggle with Synchronous LED Circuit (5.0) Dia .197 (14.7) .579 (14.7) .579 (6.2) Dia .244 1/4-40 Thd Standard Hardware: 2 AT513H Hex Nuts, 1 AT507H Locking Ring, 1 AT509 Lockwasher Standard & optional hardware details in Accessories & Hardware section. Threaded Bushing combines with Terminal codes 01, 02, & 03. Smooth Bushing combines with Terminal code 30. (6.5) Dia .256 (2.2) Dia .087 (6.1) .240 Max. Panel Thickness without Locking Ring .134" (3.4mm) (6.5) Dia .256 (5.8) .228 (0.6) .024 Tilt Tactiles Finish: Brushed aluminum Max. Panel Thickness with Standard Hardware .102" (2.6mm) 20 20 (5.0) Dia .197 Solder Lug (4.8) .189 1/4-40 Thd 20 (2.5) Dia .098 (5.0) Dia .197 Accessories Supplement Single Pole Keyway Indicators Touch TYPICAL SWITCH DIMENSIONS M2112TCFW01 A84 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (14.7) .579 (8.0) .315 (0.9) .035 (20.3) .799 (6.35) .250 Single color LED switch does not have terminal 5. www.nkkswitches.com (1.17) Typ .046 6 3 5 2 4 1 (4.8) .189 (13.0) .512 (2.0) Typ .079 A TYPICAL SWITCH DIMENSIONS Solder Lug Rockers Double Pole Toggles Series M2100 LED Tipped Toggles (17.5) .689 (14.7) .579 (0.9) .035 (8.0) .315 (20.3) .799 6 3 8 5 2 7 4 1 (2.0) Typ .079 (4.8) Typ .189 (1.17) Typ .046 (6.35) .250 (13.0) .512 M2122TCFW01 Single color LED switch does not have terminal 8. (2.5) Dia .098 (6.2) Dia .244 (5.0) Dia .197 (2.9) .114 (1.4) .055 4 5 6 1 2 3 (12.7) .500 Slides Keyway Right Angle PC Rotaries Single Pole Only (4.3) .169 (5.1) .201 (13.0) .512 (14.7) .579 (7.6) .299 (0.4) .016 (1.1) .043 (16.4) .646 Single color LED switch does not have terminal 5. (1.27) Typ .050 (3.81) .150 (0.8) Typ .031 (4.7) Typ .185 Gold contact material only Tactiles (2.5) Dia .098 (5.0) Dia .197 (4.7) Typ .185 9 Pushbuttons 20 (0.8) Typ .031 Programmable Illuminated PB (4.8) .189 1/4-40 Thd Keylocks Keyway M2112TCFG30 Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Accessories Indicators W Touch CONTACT MATERIALS & RATINGS Tilt (6.35) .250 Supplement Complete explanation of operating range in Supplement section. www.nkkswitches.com A85 TERMINALS 01 Solder Lug with Turret LED Terminal (6.35) (4.8) .250 .189 Quick Connect (6.35) (4.8) .250 .189 (2.0) .079 (1.1) .043 (1.17) .046 03 Straight PC with Turret LED Terminal Single Pole (4.8) .189 3 (6.35) (4.8) .250 .189 Epoxy Seal (1.17) Typ .046 (4.8) .189 Thk = (0.8) Typ .031 2 1 Double Pole Single color LED & isolated bicolor LED switches do not have terminal 5. 6 5 Epoxy Seal (1.57) Typ .062 (4.8) .189 Thk = (0.8) Typ .031 (4.8) .189 Thk = (0.8) Typ .031 (4.7) Typ .185 4 3 6 9 2 5 8 1 4 7 (4.8) Typ .189 (4.7) Typ .185 Single color LED & isolated bicolor LED switches do not have terminal 8. (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole 30 (4.7) Typ .185 Right Angle PC 6 5 4 3 2 1 LED terminals only available in brass with silver plating (3.81) .150 (16.4) .646 Single color LED & isolated bicolor LED switches do not have terminal 5. (1.8) Dia Typ .073 (2.54) Typ .100 Tactiles Slides Rotaries 02 (2.0) .079 (4.0) .157 Epoxy Seal Keylocks Programmable Illuminated PB LED Tipped Toggles A Pushbuttons Rockers Toggles Series M2100 Touch Tilt STANDARD MOUNTING HARDWARE AT513H Hexagon Nut (2 per switch) AT507H Locking Ring (1 per switch) AT509 Lockwasher (1 per switch) Material: Brass with nickel plating Material: Steel with chromate over zinc Material: Steel with chromate over zinc (6.35) Dia .250 Indicators 1/4-40 Thd (8.0) .315 (12.0) Dia .472 (2.0) .079 (6.4) Dia (10.2) Dia .252 .402 Accessories (5.8) .229 (9.0) .354 (1.5) .059 (1.7) .067 (0.8) .031 Supplement Optional Hardware: Knurled nuts, dress nuts, and ON-OFF plates are available; see details in Accessories & Hardware section. A86 www.nkkswitches.com (0.5) .020