©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CHIP/CAPACITORS
Tin Lead L Termination
C0805 C103 K 5 R A L*
CERAMIC
SIZE CODE
SPECIFICATION
C - Standard
CAPACITANCE CODE
Expressed in Picofarads (pF)
First two digits represent significant figures.
Third digit specifies number of zeros. (Use 9
for 1.0 through 9.9pF. Use 8 for 0.5 through 0.99pF)
(Example: 2.2pF = 229 or 0.50 pF = 508)
CAPACITANCE TOLERANCE
B – ±0.10pF J – ±5%
C – ±0.25pF K – ±10%
D – ±0.5pF M – ±20%
F – ±1%
G – ±2%
DIMENSIONS—MILLIMETERS AND (INCHES)
CAPACITOR ORDERING INFORMATION
CAPACITOR OUTLINE DRAWINGS
END METALLIZATION
L - SnPb plated nickel barrier
(SnPb 5% minimum)
FAILURE RATE LEVEL
A- Not Applicable
TEMPERATURE CHARACTERISTIC
Designated by Capacitance
Change Over Temperature Range
G – C0G (NP0) (±30 PPM/°C)
R – X7R (±15%) (-55°C + 125°C)
P – X5R (±15%) (-55°C + 85°C)
VOLTAGE
1 - 100V 3 - 25V
2 - 200V 4 - 16V
5 - 50V 8 - 10V
9 - 6.3V
* Part Number Example: C0805C103K5RAL (14 digits - no spaces)
* Note: Indicates EIA Preferred Case Sizes (Tightened tolerances apply for 0402, 0603, and 0805 packaged in bulk cassette, see page 96.)
† For extended value 1210 case size
– solder reflow only.
(Standard Chips - For
Military see page 87)
KEMET’s line of Tin/Lead termination commercial MLCC surface mount capacitors are designed to meet the needs of the
commercial, high reliability, and military customer applications where Tin/Lead plating is required. KEMET’s Tin/Lead elec-
troplating process is designed to meet a 5% minimum lead content in the termination of the component. As the bulk of the
electronics industry marches to RoHS compliance it is important that KEMET provide the Tin/Lead terminated products for
our valued high reliability and military customers.
KEMET Tiin/Lead MLCC surface mount capacitors are available in standard EIA case sizes from 0402 to 2225 and standard
capacitance values in X7R, X5R, C0G dielectrics. Voltage ratings range from 6.3V to 200V. To order the Tin/Lead termina-
tions indicate an “L” in the 14th digit of the part number. For additional dielectrics and voltage ratings please contact the fac-
tory or local Sales personnel.
FEATURES
Refer to pages 73-76 for NP0/C0G, X7R and X5R dielectric capacitance ranges available.
WL
B
S
T
CONDUCTIVE METALLIZATIONELECTRODES
Sn/Pb PLATE
NICKEL PLATE
KEMET Tin/Lead MLCC surface mount capacitors are available in standard EIA case sizes from 0402 to 2225 and standard
capacitance values in X7R and C0G dielectrics. Voltage ratings range from 6.3V to 200V. To order the Tin/Lead terminations
indicate an “L” in the 14th digit of the part number. To request the L Series termination for other surface mount product lines (Open
Mode, High Voltage, Arrays, etc.) or for additional dielectrics and higher voltage ratings, please contact the factory or local Sales
representative.
77
Ceramic Surface Mount
6 - 35V
EIA SIZE
CODE METRIC
SIZE CODE L - LENGTH W - WIDTH T
THICKNESS B - BANDWIDTH S
SEPARATION
minimum
MOUNTING
TECHNIQUE
0201* 0603 0.6 (.024) ± .03 (.001) 0.3 ± (.012) ± .03 (.001) 0.15 (.006) ± .05 (.002) N/A
0402* 1005 1.0 (.04) ± .05 (.002) 0.5 (.02) ± .05 (.002) 0.20 (.008) -.40 (.016) 0.3 (.012)
0603 1608 1.6 (.063) ± .15 (.006) 0.8 (.032) ± .15 (.006) 0.35 (.014) ± .15 (.006) 0.7 (.028)
0805* 2012 2.0 (.079) ± .20 (.008) 1.25 (.049) ± .20 (.008) 0.50 (.02) ± .25 (.010) 0.75 (.030)
1206* 3216 3.2 (.126) ± .20 (.008) 1.6 (.063) ± .20 (.008) 0.50 (.02) ± .25 (.010) N/A
1210* 3225 3.2 (.126) ± .20 (.008) 2.5 (.098) ± .20 (.008) 0.50 (.02) ± .25 (.010) N/A
1808 4520 4.5 (.177) ± .30 (.012) 2.0 (.079) ± .20 (.008) 0.60 (.024) ± .35 (.014) N/A
1812 4532 4.5 (.177) ± .30 (.012) 3.2 (.126) ± .30 (.012) 0.60 (.024) ± .35 (.014) N/A
1825* 4564 4.5 (.177) ± .30 (.012) 6.4 (.252) ± .40 (.016) 0.60 (.024) ± .35 (.014) N/A
2220 5650 5.6 (.220) ± .40 (.016) 5.0 (.197) ± .40 (.016) 0.60 (.024) ± .35 (.014) N/A
2225 5664 5.6 (.220) ± .40 (.016) 6.3 (.248) ± .40 (.016) 0.60 (.024) ± .35 (.014) N/A
Solder Wave +
or
Solder Reflow
See page 78
for thickness
dimensions.
Solder Reflow
Solder Reflow
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CHIP CAPACITORS
This ch
Thickness Code Reference Chart
Packaging Quantity Based on Finished Chip Thickness Specifications
78
This chart refers to ceramic chip thickness codes on pages 73 – 76.
Note: TU suffix represents tape and reel packaging of unmarked components.
Note: TM suffix represents tape and reel packaging of marked components.
Cases sizes d1210 are 8mm tape with 4mm pitch and Case Sizes >1210 are 12mm tape and 8mm pitch.
art refers to ceramic chip thickness codes on pages 73-76.
Thickness
Code Chip
Size Chip Thickness
Range (mm) Qty per Reel
7" Plastic Qty per Reel
13" Plastic Qty per Reel
7" Paper Qty per Reel
13" Paper Qty per Bulk
Cassette
A
A 0201 0.30 ± 0.03 N/A N/A 15,000 N/A N/A
BB 0402 0.50 ± 0.05 N/A N/A 10,000 50,000 50,000
CB 0603 0.80 ± 0.07 N/A N/A 4,000 10,000 15,000
CC 0603 0.80 ± 0.10 N/A N/A 4,000 10,000 N/A
CD 0603 0.80 ± 0.15 N/A N/A 4,000 10,000 N/A
DB 0805 0.60 ± 0.10 N/A N/A 4,000 10,000 10,000
DC 0805 0.78 ± 0.10 N/A N/A 4,000 10,000 N/A
DD 0805 0.90 ± 0.10 N/A N/A 4,000 10,000 N/A
DE 0805 1.00 ± 0.10 2,500 10,000 N/A N/A N/A
DF 0805 1.10 ± 0.10 2,500 10,000 N/A N/A N/A
DG 0805 1.25 ± 0.15 2,500 10,000 N/A N/A N/A
DH 0805 1.25 ± 0.20 2,500 10,000 N/A N/A N/A
DJ 0805 1.25 ± 0.20 3,000 N/A N/A N/A N/A
DK 0805 1.25 ± 0.15 3,000 N/A N/A N/A N/A
DL 0805 0.95 ± 0.10 4,000 10,000 N/A N/A N/A
EB 1206 0.78 ± 0.10 4,000 10,000 4,000 10,000 N/A
EC 1206 0.90 ± 0.10 4,000 10,000 N/A N/A N/A
ED 1206 1.00 ± 0.10 2,500 10,000 N/A N/A N/A
EE 1206 1.10 ± 0.10 2,500 10,000 N/A N/A N/A
EF 1206 1.20 ± 0.15 2,500 10,000 N/A N/A N/A
EG 1206 1.60 ± 0.15 2,000 8,000 N/A N/A N/A
EH 1206 1.60 ± 0.20 2,000 8,000 N/A N/A N/A
EJ 1206 1.70 ± 0.20 2,000 8,000 N/A N/A N/A
EK 1206 0.80 ± 0.10 2,000 8,000 N/A N/A N/A
EL 1206 1.15 ± 0.15 2,000 8,000 N/A N/A N/A
EM 1206 1.25 ± 0.15 2,500 10,000 N/A N/A N/A
EN 1206 0.95 ± 0.10 4,000 10,000 N/A N/A N/A
FB 1210 0.78 ± 0.10 4,000 10,000 N/A N/A N/A
FC 1210 0.90 ± 0.10 4,000 10,000 N/A N/A N/A
FD 1210 0.95 ± 0.10 4,000 10,000 N/A N/A N/A
FE 1210 1.00 ± 0.10 2,500 10,000 N/A N/A N/A
FF 1210 1.10 ± 0.10 2,500 10,000 N/A N/A N/A
FG 1210 1.25 ± 0.15 2,500 10,000 N/A N/A N/A
FH 1210 1.55 ± 0.15 2,000 8,000 N/A N/A N/A
FJ 1210 1.85 ± 0.20 2,000 8,000 N/A N/A N/A
FK 1210 2.10 ± 0.20 2,000 8,000 N/A N/A N/A
FL 1210 1.40 ± 0.15 2,000 8,000 N/A N/A N/A
FM 1210 1.70 ± 0.20 2,000 8,000 N/A N/A N/A
FN 1210 1.85 ± 0.20 2,000 8,000 N/A N/A N/A
FO 1210 1.50 ± 0.20 2,000 8,000 N/A N/A N/A
FP 1210 1.60 ± 0.20 2,000 8,000 N/A N/A N/A
FQ 1210 2.50 ± 0.22 1,500 N/A N/A N/A N/A
FR 1210 2.25 ± 0.20 2,000 8,000 N/A N/A N/A
FS 1210 2.50 ± 0.20 1,000 4,000 N/A N/A N/A
FT 1210 1.90 ± 0.20 1,500 4,000 N/A N/A N/A
LD 1808 0.90 ± 0.10 4,000 10,000 N/A N/A N/A
GB 1812 1.00 ± 0.10 1,000 4,000 N/A N/A N/A
GC 1812 1.10 ± 0.10 1,000 4,000 N/A N/A N/A
GD 1812 1.25 ± 0.15 1,000 4,000 N/A N/A N/A
GE 1812 1.30 ± 0.10 1,000 4,000 N/A N/A N/A
GF 1812 1.50 ± 0.10 1,000 4,000 N/A N/A N/A
GG 1812 1.55 ± 0.10 1,000 4,000 N/A N/A N/A
GH 1812 1.40 ± 0.15 1,000 4,000 N/A N/A N/A
GJ 1812 1.70 ± 0.15 1,000 4,000 N/A N/A N/A
GK 1812 1.60 ± 0.20 1,000 4,000 N/A N/A N/A
GL 1812 1.90 ± 0.20 1,000 4,000 N/A N/A N/A
GM 1812 2.00 ± 0.20 1,000 4,000 N/A N/A N/A
GN 1812 1.70 ± 0.20 1,000 4,000 N/A N/A N/A
GO 1812 2.50 ± 0.20 500 N/A N/A N/A N/A
HB 1825 1.10 ± 0.15 1,000 4,000 N/A N/A N/A
HC 1825 1.15 ± 0.15 1,000 4,000 N/A N/A N/A
HD 1825 1.30 ± 0.15 1,000 4,000 N/A N/A N/A
HE 1825 1.40 ± 0.15 1,000 4,000 N/A N/A N/A
HF 1825 1.50 ± 0.15 1,000 4,000 N/A N/A N/A
JB 2220 1.00 ± 0.15 1,000 4,000 N/A N/A N/A
JC 2220 1.10 ± 0.15 1,000 4,000 N/A N/A N/A
JD 2220 1.30 ± 0.15 1,000 4,000 N/A N/A N/A
JE 2220 1.40 ± 0.15 1,000 4,000 N/A N/A N/A
JF 2220 1.50 ± 0.15 1,000 4,000 N/A N/A N/A
JG 2220 1.70 ± 0.15 1,000 4,000 N/A N/A N/A
JH 2220 1.80 ± 0.15 1,000 4,000 N/A N/A N/A
JO 2220 2.40 ± 0.15 500 2,000 N/A N/A N/A
KB 2225 1.00 ± 0.15 1,000 4,000 N/A N/A N/A
KC 2225 1.10 ± 0.15 1,000 4,000 N/A N/A N/A
KD 2225 1.30 ± 0.15 1,000 4,000 N/A N/A N/A
KE 2225 1.40 ± 0.15 1,000 4,000 N/A N/A N/A
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
KEMET offers Multilayer Ceramic Chip Capacitors
packaged in 8mm and 12mm plastic tape on 7" and
13" reels in accordance with EIA standard 481-1:
Taping of surface mount components for automatic
handling. This packaging system is compatible with all
tape
fed
automatic
pick
and
place
systems. See page 78
for details on reeling quantities for commercial chips
and page 87 for MIL-PRF-55681 chips.
CERAMIC CHIP CAPACITORS
Packaging Information
Tape & Reel Packaging
8mm ±.30
(.315 ±.012")
or
12mm ±.30
(.472 ±.012")
178mm (7.00")
or
330mm (13.00")
Anti-Static Reel
Embossed Carrier*
0402 and 0603 case sizes
available on punched paper only.
Embossment
Anti-Static Cover Tape
(.10mm (.004") Max Thickness)
Chip Orientation
in Pocket
(except 1825 Commercial, and 1825 & 2225 Military)
* Punched paper carrier used for 0402 and 0603 case size.
g
handling. This packaging system is compatible with all
tape
fed
automatic
pick
and
place
systems. See page 81
for details on reeling quantities for commercial chips
and page 90 for MIL-PRF-55681 chips.
KEMET
®
X
C
G
Z
Y
Grid
placement
courtyard Z
2.14
2.78
3.30
4.50
4.50
5.90
5.90
7.00
7.00
G
0.28
0.68
0.70
1.50
1.50
2.30
2.30
3.30
3.30
X
0.74
1.08
1.60
2.00
2.90
3.70
6.90
5.50
6.80
Y(ref)
0.93
1.05
1.30
1.50
1.50
1.80
1.80
1.85
1.85
C(ref)
1.21
1.73
2.00
3.00
3.00
4.10
4.10
5.15
5.15
Z
3.18
3.70
4.90
4.90
G
0.68
0.70
1.50
1.50
X
0.80
1.10
1.40
2.00
Y(ref)
1.25
1.50
1.70
1.70
Smin
1.93
2.20
3.20
3.20
Wave SolderReflow Solder
Calculation Formula
Z = Lmin + 2Jt + Tt
G = Smax - 2Jh -Th
X = Wmin + 2Js + Ts
Tt, Th, Ts = Combined tolerances
0402
0603
0805
1206
1210
1812
1825
2220
2225
Dimension
Not Recommended
Not Recommended
C
X
Grid
Placement
Courtyard
GY
Z
SURFACE MOUNT LAND DIMENSIONS - CERAMIC CHIP CAPACITORS - MM
93
Packaging
Case Sizes ≤ 1210 are 8 mm tape with 4 mm pitch.
Case Sizes >1210 are 12 mm tape with 8 mm pitch.
Note: TU suffix represents tape and reel packaging of unmarked components.
TM suffix represents tape and reel packaging of marked components.
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Performance Notes
1. Cover Tape Break Force: 1.0 Kg Minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width Peel Strength
8 mm 0.1 Newton to 1.0 Newton (10g to 100g)
12 mm 0.1 Newton to 1.3 Newton (10g to 130g)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165to 180from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
reels (with C-7280). Note that 13” reels are preferred.
4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Refer to EIA-556.
Embossed Carrier Tape Configuration: Figure 1
NOTES
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location and hole location shall be applied independent of each other.
3. Tape with components shall pass around radius “R” without damage (see sketch A). The minimum trailer length (Fig. 2) may require
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
4. The cavity defined by A0,B0,and K0shall be configured to surround the part with sufficient clearance such that the chip does not pro-
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
Table 1 — EMBOSSED TAPE DIMENSIONS (Metric will govern)
Constant Dimensions — Millimeters (Inches)
Tape Size D0EP
0P2T Max T1Max
8 mm 1.5 1.75 ±0.10 4.0 ±0.10 2.0 ±0.05 0.600 0.100
and +0.10 -0.0
12 mm (0.059 (0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002) (0.024) (0.004)
+0.004, -0.0)
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch B1Max. D1Min. F P1R Min. T2Max W A0B0K0
Note 1 Note 2 Note 3 Note 4
8 mm Single 4.4 1.0 3.5 ±0.05 4.0 ±0.10 25.0 2.5 8.0 ±0.30
(4 mm)
(0.173) (0.039) (0.138 ±0.002) (0.157 ±0.004) (0.984) (0.098) (.315 ±0.012)
12 mm Double 8.2 1.5 5.5 ±0.05 8.0 ±0.10 30.0 4.6 12.0 ±0.30
(8 mm) (0.323) (0.059) (0.217 ±0.002) (0.315 ±0.004) (1.181) (0.181) (0.472 ±0.012)
TANTALUM, CERAMIC AND
ALUMINUM CHIP CAPACITORS
Packaging Information
94
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Embossed Carrier Tape Configuration (cont.)
Sketch D: Tape Camber (Top View)
Allowable camber to be 1 mm/250 mm.
250mm (9.843)
1mm (0.039) Max.
1mm (0.039) Max.
Table 2 – REEL DIMENSIONS (Metric will govern)
Figure 3: Reel Dimensions (Metric Dimensions will govern)
Tape Size A Max B* Min C D* Min N Min W1W2Max W3
8 mm 330.0 1.5 13.0 ± 0.20 20.2 50.0 8.4 14.4 7.9 Min
(12.992) (0.059) (0.512 ± 0.008) (0.795) (1.969) +1.5, -0.0 (0.567) (0.311)
See (0.331 10.9 Max
Note 3 +0.059, -0.0) (0.429)
12 mm 330.0 1.5 13.0 ± 0.20 20.2 Table 1 12.4 18.4 11.9 Min
(12.992) (0.059) (0.512 ± 0.008) (0.795) +2.0, -0.0 (0.724) (0.469)
(0.488 15.4 Max
+0.078, -0.0) (0.606)
TANTALUM, CERAMIC AND
ALUMINUM CHIP CAPACITORS
Packaging Information
Figure 2:
Tape Leader
& Trailer
Dimensions
(Metric
Dimensions
Will Govern)
400mm (15.75) Min.
20°
95
Packaging
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
20°
20°
Maximum
component rotation.
Typical
component
center line
Punched Carrier (Paper Tape) Configuration (Ceramic Chips Only):
Table 1: 8 & 12mm Punched Tape
(Metric Dimensions Will Govern)
Variable Dimensions - Millimeters (Inches)
Note:
1. A0, B0 and T determined by the maximum dimensions to the ends of the terminals extending from the
body and/or the body dimensions of the component. The clearance between the ends of the terminals or
body of the component to the sides and depth of the cavity (A0, B0 and T) must be within 0.05mm (.002)
minimum and 0.50mm (.020) maximum. The clearance allowed must also prevent rotation of the component
within the cavity of not more than 20 degrees (see sketches A and B).
2. Tape with components shall pass around radius "R" without damage.
3. KEMET nominal thicknesses are: 0402 = 0.6mm and all others 0.95mm minimum.
8mm
and
12mm
1.5
+0.10, -0.0
(.059
+0.004, -0.0)
1.75 ±0.10
(.069 ±0.004)
4.0 ± 0.10
(.157 ± 0.004)
2.0 ± 0.05
(.079 ± 0.002)
0.10
(.004)
Max.
0.75
(.030)
Min.
0.75
(.030)
Min.
25 (.984)
See Note 2
Table 1
Tape
Size D0P0
EP2T1G1G2R Min.
8mm
1/2
Pitch
2.0 ± 0.10
(.079 ±.004)
See Require-
ments
Section 3.3 (d)
3.5 ± 0.05
(.138 ± .002)
8.0 ± 0.3
(.315 ± 0.012)
See Note 1
Table 1
1.1mm (.043)
Max. for Paper
Base Tape and
1.6mm (.063)
Max. for Non-
Paper Base
Compositions.
See Note 3.
Tape
Size P1W
FA0B0T
8mm 4.0 ± 0.10
(0.157 ± .004)
12mm 4.0 ± 0.10
(0.157 ± .004)
12mm
Double
Pitch
8.0 ± 0.10
(0.315 ± .004)
12.0 ± 0.3
(.472 ± .012)
5.5 ± 0.05
(.217 ± .002)
Table 1: 8 & 12mm Punched Tape
(Metric Dimensions Will Govern)
Constant Dimensions - Millimeters (Inches)
Sketch B:
Max. Component
Rotation - Front
Cross Sectional View
Sketch C:
Component Rotation - Top View
A
0
B
0
P
1
P
0
P
2
D
0
F
E
W
Center lines
of cavity
10 pitches cumulative
tolerance on tape
±0.2 (±0.008)
Top
Tape
Cover
T
User Direction of Feed
T
1
Max. Cavity Size
See Note 1
Table 1
Bottom
Tape
Cover
G
2
R
(Min.)
Sketch A:
Bending Radius
See Note 2
Table 1
CERAMIC CHIP CAPACITORS
Packaging Information
96
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CHIP CAPACITORS
Packaging Information
CAPACITOR MARKING TABLE
(Marking Optional - Not Available
for 0402 Size or Y5V Dielectric)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
Y
Z
a
b
d
e
f
m
n
t
y
0.10
0.11
0.12
0.13
0.15
0.16
0.18
0.20
0.22
0.24
0.27
0.30
0.33
0.36
0.39
0.43
0.47
0.51
0.56
0.62
0.68
0.75
0.82
0.91
0.25
0.35
0.40
0.45
0.50
0.60
0.70
0.80
0.90
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
2.5
3.5
4.0
4.5
5.0
6.0
7.0
8.0
9.0
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
25
35
40
45
50
60
70
80
90
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
250
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1500
1600
1800
2000
2200
2400
2700
3000
3300
3600
3900
4300
4700
5100
5600
6200
6800
7500
8200
9100
2500
3500
4000
4500
5000
6000
7000
8000
9000
10,000
11,000
12,000
13,000
15,000
16,000
18,000
20,000
22,000
24,000
27,000
30,000
33,000
36,000
39,000
43,000
47,000
51,000
56,000
62,000
68,000
75,000
82,000
91,000
25,000
35,000
40,000
45,000
50,000
60,000
70,000
80,000
90,000
100,000
110,000
120,000
130,000
150,000
160,000
180,000
200,000
220,000
240,000
270,000
300,000
330,000
360,000
390,000
430,000
470,000
510,000
560,000
620,000
680,000
750,000
820,000
910,000
250,000
350,000
400,000
450,000
500,000
600,000
700,000
800,000
900,000
Alpha
Character
Numeral
901 2 3 4 5
Capacitance (pF) For Various Numeral Identifiers
1,000,000
1,100,000
1,200,000
1,300,000
1,500,000
1,600,000
1,800,000
2,000,000
2,200,000
2,400,000
2,700,000
3,000,000
3,300,000
3,600,000
3,900,000
4,300,000
4,700,000
5,100,000
5,600,000
6,200,000
6,800,000
7,500,000
8,200,000
9,100,000
2,500,000
3,500,000
4,000,000
4,500,000
5,000,000
6,000,000
7,000,000
8,000,000
9,000,000
7
10,000,000
11,000,000
12,000,000
13,000,000
15,000,000
16,000,000
18,000,000
20,000,000
22,000,000
24,000,000
27,000,000
30,000,000
33,000,000
36,000,000
39,000,000
43,000,000
47,000,000
51,000,000
56,000,000
62,000,000
68,000,000
75,000,000
82,000,000
91,000,000
25,000,000
35,000,000
40,000,000
45,000,000
50,000,000
60,000,000
70,000,000
80,000,000
90,000,000
6
Laser marking is available as an extra-cost option for
most KEMET ceramic chips. Such marking is two
sided, and includes a K to identify KEMET, followed by
two characters (per EIA-198 - see table below) to
identify the capacitance value. Note that marking is
not available for size 0402 nor for any Y5V chip. In
addition, the 0603 marking option is limited to the K
only.
Example shown is 1,000 pF capacitor.
KA3
Table 2 – Capacitance Values Available
In Bulk Cassette Packaging
0402
0603
0805
All
All
C0G
X7R
Y5V
All
All
109
109
109
221
221
221
221
221
104
104
All
All
181
331
102
392
103
273
104
104
224
224
Case
Size Dielectric Voltage
Min.
Cap
Value
Max.
Cap
Value
All
All
200
100
50
200
100
50
25
16
25
16
Terminations: KEMET nickel barrier layer with a tin overplate.
0.3
0.7
0.75
EIA
Size
Code
Length
L
Width
W
Thickness
T
Bandwidth
B
Minimum
Separation
S
Metric
Size
Code
Number of
Pcs/Cassette
50,000
15,000
10,000
0402
0603
0805
1.0 ± 0.05
1.6 ± 0.07
2.0 ± 0.10
0.5 ± 0.05
0.8 ± 0.07
1.25 ± 0.10
0.5 ± .05
0.8 ± .07
0.6 ± .10
0.2 to 0.4
0.2 to 0.5
0.5 to 0.75
1005
1608
2012
Table 1 – Capacitor Dimensions for Bulk
Cassette Packaging – Millimeters
Unit: mm
* Reference
110 ± 0.7
31.5 ±0
0.2
36 ±0
0.2
19.0*
5.0*
10*
53.3*
6.8 ± 0.1
8.8 ± 0.1
12.0 ± 0.1
3.0 ±0
0.2
2.0 ±0.1
0
1.5 ±0
0.1
Bulk Cassette Packaging (Ceramic Chips only)
(Meets Dimensional Requirements IEC-286-6 and EIAJ 7201)
97
Packaging
