| |1000pF i 2KV | 1 @ @ @/@|@)@ a | a if ELECTRICAL SPECIFICATIONS: NOTES 1.0 PINS WITHOUT ELECTRICAL 1.0 TURNS RATIO P6-PS-P4) 1: (J6-J3) 1CT : 1CT 3% CONNECTION ARE OMITTED. P3-Pe-P1) 1 J2e-JD 11CT : 1cCT + 3% 2.0 INDUCTANCE (P6-P4) + 350uH MIN, @ OLV , 100KHz, 8mA DC Blos (P3-Pb : 350uH MIN. @ OL1V, LOOKHz, 8mA DC Blas 3.0 LEAKAGE INDUCTANCE P6-P4 CWITH J6 AND J3 SHORT) : 0.3 MAX. @ iIMHz P3-P1 CWITH Je AND Ji SHORT) : 0.3 MAX. @ 1IMHz 4,0 INTERWINDING CAPACITANCE (P6,P5,P4) TO J6,J3> : 30pf MAX @ 1MHz CP3,P2,Pi TO (J2,JbD : 30pf MAX. @ 1MHZ 0.0 DC RESISTANCE CJ6-J3)=(J2-JD 1 Le ohms Max. InNet Technologies Inc. httpi//wwwdinnettech.com Stewart Connector Systems httpi//www.stewortconnector.com TOF 4 DRAWING NO. S1-40043 me6.0 RETURN LOSS: P6-P4)=100 DHMS AND P1-P35=100 OHM REF. IMHz TO 30MHz 60MHz TO 80MHz NOTE: 100 OHMS CONNECTED TO (J2e-Ji2 OR (J6-J3), 7.0 VOLTAGE WITHSTAND: (J1, J2) TO P1, P3d (J3, J6> TO (P4,P6) 8.0 INSERTION LOSS: RS=RL=100 ohms 100KHz TO 100MHz 9.0 RISE TIME! RS=100 OHMS AND RL = 100 OHMS OUTPUT VOLTAGE = 1 V peak PULSE WIDTH= 11enS 10,0 CROSS TALK! 1MHz TO 100MHz 11.0 COMMON TO COMMON MODE ATTENUATION: 30MHz TO 100MHz | 18c0B MIN. ! 12dB MIN. : 1500 VAC 1 1500 VAC Ll dB TYP 3.0 nS MAX 3.0 nS MAX 40 odB TYP 3D50B TYP InNet Technologies Inc. httpi//wwwdinnettech.com Stewart Connector Systems httpi//www.stewortconnector.com 2 or 4 | SI-40043 REV, Xbo *.6.55 [16.15] MAX. oy NIDIHO 40 AULNAGO 3009 avd SGAWNN Lad J3N4| I B50 [21.59] MAX.\*+ 708 [17.98}=4 REF. BICOLOR LED POLARITY REF. aa 148 [3.75] HIGHEST POINT OF BEAM | 599 [15.21] REF. \ Ht a Pe ANT | L - \ J I | pe-.425 [10.79] - +,005 -D40 [1.02] 4.005 05D [1.27] TP TOL NON- 025 [0.64] 100 [2.54] TYP 0.035 [0.80] (8) PIN? <S Cts 9.062 [1.57] (2) % att ACCUM NONACCUM 100 [2.54] .250 [6.35] 3 4128 [3.25] opt * a5 [318] A set 0.04q[1.02 4) 4] 1143 BICCLOR GRN/YEL LED wo 6f) OF lt ig 7 gs oS = a <* ou [15.49] GAN /YEL LD P.C.B_ RECOMMENDED HOLE LAYOUT SEEN (ae) COMPONENT SIDE TOLERANCE .005 [0.08] UNLESS OTHERWSE SPECFIED ee 110-.150 [2,80-3.81] oO NOTES. TOLERANCES COMPLY WITH F.C.C, DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH "* TO BE CENTRAL AROUT CENTER LINE DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE. PIN NOT ELECTRICALLY CONNECTED MAYBE OMITTED. SEE ELECTRICAL DRAWING FOR OMITTED PINS. AVAILABLE WITH: STANDARD 5@ MICRO-INCH SELECTIVE GOLD PLATING LED SPECIFICATIONS YELLOW GREEN FORWARD VOLTAGE(20mA) ; 2.5v (MAX) 2.5v (MAX) FORWARD VOLTAGE(20mA) : 2.1V (TYP) 3.2v (TYP) POWER DISSIPATION ; 105mW 105 mW WAVE LENGTH: 59dnm 565m LUMINOUS INTENSITY (10mA) ; 2-8 MCD 8-32MCD InNet Technologies Inc. http://www.inne ttech.com Stewart Connector Systems httpi//www.stewor tconnector.com "0 ] | of 4 DRAVING NO, SI-400431300 1200 1100 1000 900 800 700 600 500 400 500 200 100 KR [ | / [ ft + PANEL GROUNDING BEAM DEFLECTION 5.0.8. = SUGGESTED OPENING SIZE : L .000 (TOP OF PCB TO BOTTOM OF OPENING) 010 MAX. RADIUS(4) SUGGESTED PANEL OPENING CT720034x1 /24001302 POINT OF CONTACT WITH PANEL Ee __& | 1.275 max THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .013 ON THE BOTTOM, AT PANEL OPENING. InNet Technologies Inc. http://www.inne ttech.com Stewart Connector Systems httpi//www.stewor tconnector.com A of 4 DRAVING NO, S I-40 0 4 3 OL