GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Features Compliant to RoHS EU Directive 2011/65/EU (Z versions) Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this produc twill no longer be RoHS compliant (non-Z versions) Delivers up to 25A Output current High efficiency - 92.5% at 3.3V full load Industry standard Quarter brick footprint 57.9mm x 36.8mm x 12.7mm (with base plate) RoHS Compliant Applications (2.28in x 1.45in x 0.5in) Low output ripple and noise 2:1 Input voltage Wireless Networks Input under voltage protection Optical and Access Network Equipment Output overcurrent/voltage protection Enterprise Networks Over-temperature protection Latest generation IC's (DSP, FPGA, ASIC) and Microprocessor powered applications Tightly regulated output Remote sense Adjustable output voltage (+10%/ -20%) Negative logic, Remote On/Off Auto restart after fault protection shutdown Wide operating temperature range (-40C to 85C) Meets the voltage insulation requirements for ETSI 300132-2 and complies with and is Licensed for Basic Insulation rating per EN 60950 CE mark meets the 2006/95/EC directive UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03 Certified, and VDE 0805 (EN60950 3rd Edition) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Options Negative Remote On/Off Logic Auto-restart from Output overcurrent/voltage and Over-temperature Protections Heat plate version (-H) Description The QPW025A0F41 is a new open-frame DC/DC power module designed to provide up to 25A output current in an industry standard quarter brick package. The converter uses synchronous rectification technology and open-frame packaging techniques to achieve high efficiency reaching 92.5% at 3.3V full load. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. This product is intended for integration into end-user equipment. All of the required procedures of end-use equipment should be followed. ** ISO is a registered trademark of the International Organization of Standards October 5, 2015 (c)2012 General Electric Company. All rights reserved. GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous All VIN - 80 Vdc VIN, trans - 100 Vdc All TA -40 85 C Storage Temperature All Tstg -55 I/O Isolation All Transient (100 ms) Operating Ambient Temperature (see Thermal Considerations section) 125 C 1500 Vdc Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit All VIN 36 48 75 Vdc All IIN,max - 2.9 Adc All IIN, Q - 5 mA All IIN, Idle - - mA Inrush Transient All I2t - 1 A2s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12H source impedance; Ta 25oC, Cin = TBD) All - 16 - mAp-p Input Ripple Rejection (100 - 120Hz) All - 60 - dB Operating Input Voltage Maximum Input Current (VIN=0 to VIN, max , Vo = Vo,set, IO=IO, max ) Quiescent Input Current Remote on / off disabled (VIN = VIN, nom) Idle Input Current Remote on / off enabled (VIN = VIN, nom, Io = 0 A) 60 CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data sheet for further information. October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 2 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Symbol Min Typ Max Unit VO, set 3.24 3.3 3.36 % VO, set (VIN=VIN,nom, IO=IO, max, Tref=25C) -1.6 +1.6 % VO, set 3.2 - 3.4 % VO Line (VIN = VIN, min to VIN, max) 0.05 0.2 % VO, nom Load (IO = IO, min to IO, max) 0.05 0.2 % VO, nom 0.15 0.50 % VO, nom 10 20 mVrms mVpk-pk Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Output Regulation VO Temperature (Tref =TA, min to TA, max) Output Ripple and Noise on nominal output (VIN =VIN, nom and IO = IO, min to IO, max, Cout = 1F ceramic // 10F Tantalum capacitor) RMS (5Hz to 20MHz bandwidth) 45 60 External Capacitance CO 0 10000 F Output Current Io 0 25 A dc Output Current Limit Inception (Hiccup Mode) (Vo = 90% Vo, set ) IO, lim 105 120 130 % Io, max Output Short-Circuit Current IO, s/c 130 150 % Io, max Peak-to-Peak (5Hz to 20MHz bandwidth) VO 250 mV @ 25o C Efficiency 92.5 % fsw 300 KHz Peak Deviation Vpk 5 % VO Settling Time (VO<10% peak deviation) ts 150 s Peak Deviation Vpk 5 % VO Settling Time (VO<10% peak deviation) ts 150 s VIN= 48V, TA=25C, IO= IO, max A Switching Frequency Dynamic Load Response (dIO/dt=0.1A/s; VIN=VIN, nom; TA=25C) Load change from IO = 50% to 75% of IO, max Load change from IO = 50% to 25% of IO, max, Isolation Specifications Symbol Min Typ Max Unit Isolation Capacitance Parameter CISO 2700 pF Isolation Resistance RISO 10 M Symbol Min Typ Max Unit General Specifications Parameter Calculated Reliability based upon Telcordia SR-332, Issue 2; Method I Case 3 (IO= 80% of IO, max, TA=40C, airflow = 200 lfm, 90% confidence) Weight October 5, 2015 2,808,445 356 MTBF FIT 31 (1.1) (c)2012 General Electric Company. All rights reserved. Hours 109/Hours g (oz.) Page 3 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Symbol Min Typ Max Unit On/Off Signal interface (VI = VI,min to VI, max; Open collector or equivalent Compatible, signal referenced to VI (-) terminal Logic High (Module ON) Input High Voltage VIH 7 -- 15 V Input High Current IIH -- -- 50 A Logic Low (Module OFF) Input Low Voltage VIL 0 -- 1.2 V Input Low Current IIL -- -- 1 mA Case 1: On/Off input is set to Logic High (Module ON) and then input power is applied (delay from instant at which VIN = VIN, min until Vo=10% of Vo,set) Tdelay -- 5 -- msec Case 2: Input power is applied for at least one second and then the On/Off input is set to logic high (delay from instant at which Von/Off=0.9V until Vo=10% of Vo, set) Tdelay -- 2.5 -- msec Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) Trise -- 4 -- msec -- -- 10 % VO, set -- 1 % VO, set 115 C 34.5 36 V 30 31.5 V Turn-On Delay and Rise Times (IO=80% IO, max , VIN=VIN, nom, TA = 25 oC) Output Voltage Remote Sense Output voltage overshoot - Startup IO= 80% of IO, max; TA = 25oC Over temperature Protection Tref (See Thermal Considerations section) Input Undervoltage Lockout Turn-on Threshold Turn-off Threshold VUVLO 3 Hysteresis Output voltage adjustment range(TRIM) 80 110 % VO, set Over voltage protection 3.8 4.6 Vdc October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 4 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Characteristic Curves The following figures provide typical characteristics for QPW025A0F41/QPW025A0F41-H at 25O C 3 OUTPUT VOLTAGE Vo(V) (1V/div) ON/OFF VOLTAGE VOn/Off (V) (5V/div) INPUT CURRENT,(A) 2.5 2 Io = 25.0A 1.5 Io = 12.5A 1 0.5 Io = 0.0A 0 30 40 50 60 INPUT VOLTAGE, VIN (V) 70 Figure 1. Typical Start-Up (Input Current) characteristics at room temperature. TIME, t (2 ms/div) Figure 4. Typical Start-Up Characteristics from Remote ON/OFF. OUTPUT CURRENT OUTPUT VOLTAGE IO (A) (5A/div) VO, (V) (200mV/div) 95 90 Vin = 75V EFFICIENCY (%) Vin = 48V 85 Vin = 36V 80 75 70 0 5 10 15 20 25 TIME, t (100s/div) OUTPUT CURRENT, Io (A) Figure 5. Transient Response to Dynamic Load Change from 50% to 25% to 50% of full load current. OUTPUT CURRENT OUTPUT VOLTAGE IO (A) (5A/div) VO (V) (200mV/div) VO (V) (20mV/div) OUTPUT VOLTAGE Figure 2. Converter Efficiency Vs Load at Vo= 3.3 V. TIME, t (2s/div) TIME, t (100s/div) Figure 3. Typical Output Ripple and Noise at Vin =48Vdc. October 5, 2015 Figure 6. Transient Response to Dynamic Load Change from 75% to 50 % to 75% of full load current. (c)2012 General Electric Company. All rights reserved. Page 5 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Test Configurations Design Considerations TO OSCILLOSCOPE LTEST VI(+) 12 H CS 220 F ESR < 0.1 W @ 20 C, 100 kHz BATTERY Input Source Impedance CURRENT PROBE 33 F ESR < 0.7 W @ 100 kHz VI(-) Note: Input reflected-ripple current is measured with the simulated source inductance of 1uH. Capacitor Cs offsets possible battery impedance. Current is measured at the input of the module Figure 7. Input Reflected Ripple Current Test Setup. COPPER STRIP V O (+) RESISTIV LOAD 1.0 F 10 F SCOPE V O (-) GROUND PLANE Note: Use a 10uF tantalum and a 1uF ceramic capacitor. Scope measurement should be made using BNC socket. Position the load between 51 mm and 76mm (2 in. and 3 in.) from the module Figure 8. Output Ripple and Noise Test Setup. SENSE(+) CONTACT AND DISTRIBUTION LOSSES VO(+ ) V I(+) II IO LOAD SUPPLY V I(-) CONTACT RESISTANCE High output current transient rate of change (high di/dt) loads may require high values of output capacitance to supply the instantaneous energy requirement to the load. To minimize the output voltage transient drop during this transient, low E.S.R. (equivalent series resistance) capacitors may be required, since a high E.S.R. will produce a correspondingly higher voltage drop during the current transient. Output capacitance and load impedance interact with the power module's output voltage regulation control system and may produce an 'unstable' output condition for the required values of capacitance and E.S.R. Minimum and maximum values of output capacitance and of the capacitor's associated E.S.R. may be dictated, depending on the module's control system. The process of determining the acceptable values of capacitance and E.S.R. is complex and is loaddependant. GE provides Web-based tools to assist the power module end-user in appraising and adjusting the effect of various load conditions and output capacitances on specific power modules for various load conditions Safety Considerations SENSE(-) VO. IO = Output Capacitance V O(-) Figure 9. Output Voltage and Efficiency Test Setup. Efficiency The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. For the test configuration in Figure 7, a 33 F electrolytic capacitor (ESR < 0.7 at 100 kHz) mounted close to the power module helps ensure stability of the unit. Consult the factory for further application guidelines. VIN. IIN x 100 % For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL60950-1, CSA C22.2 No. 60950-1-03, EN60950-1 and VDE 0805:2001-12. For end products connected to -48V dc, or -60Vdc nominal DC MAINS (i.e. central office dc battery plant), no further fault testing is required. For all input voltages, other than DC MAINS, where the input voltage is less than 60V dc, if the input meets all of the requirements for SELV, then: The output may be considered SELV. Output voltages will remain within SELV limits even with internally-generated non-SELV voltages. Single component failure and fault tests were performed in the power converters. October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 6 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current One pole of the input and one pole of the output are to be grounded, or both circuits are to be kept floating, to maintain the output voltage to ground voltage within ELV or SELV limits. For all input sources, other than DC MAINS, where the input voltage is between 60 and 75V dc (Classified as TNV-2 in Europe), the following must be meet, if the converter's output is to be evaluated for SELV: leakage current of the switch is 50 A. If not using the remote on/off feature, do one of the following: For positive logic, leave the ON/OFF pin open. For negative logic, short the ON/OFF pin to VIN(-). Ion/off + ON/OFF Von/off - SENSE(+) VO(+) The input source is to be provided with reinforced insulation from any hazardous voltage, including the ac mains. One Vi pin and one Vo pin are to be reliably earthed, or both the input and output pins are to be kept floating. Another SELV reliability test is conducted on the whole system, as required by the safety agencies, on the combination of supply source and the subject module to verify that under a single fault, hazardous voltages do not appear at the module's output. The power module has ELV (extra-low voltage) outputs when all inputs are ELV. All flammable materials used in the manufacturing of these modules are rated 94V-0, or tested to the UL60950 A.2 for reduced thickness. The input to these units is to be provided with a maximum 6A fast-acting (or time-delay) fuse in the unearthed lead. Feature Descriptions Remote On/Off Two remote On/Off logic options are available. Positive logic remote On/Off turns the module ON during a logic-high voltage on the remote On/Off pin, and turns the module OFF during a logic-low. Negative logic remote On/Off turns the module OFF during a logichigh and turns the module ON during logic-low. Negative logic is specified by suffix "1" at the end of the device code. To turn the power module on and off, the user must supply a switch to control the voltage between the ON/OFF pin and the VIN(-) terminal (Von/Off). The switch may be an open collector or equivalent (see Figure 10). A logic-low is Von/off = 0 V to 1.2V. The maximum Ion/off during a logic low is 1 mA. The switch should maintain a logic-low voltage while sinking 1 mA. LOAD VO(-) VI(+) VI(-) SENSE(-) Figure 10. Circuit configuration for using Remote On/Off Implementation. Overcurrent Protection To provide protection in a fault (output overload) condition, the module is equipped with internal current-limiting circuitry, and can endure current limiting continuously. At the instance of current-limit inception, the output current begins to tail-out. When an overcurrent condition exists beyond a few seconds, the module enters a "hiccup" mode of operation, whereby it shuts down and automatically attempts to restart.. While the fault condition exists, the module will remain in this hiccup mode, and can remain in this mode until the fault is cleared. The unit operates normally once the output current is reduced back into its specified range. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage between the undervoltage lockout limit and the minimum operating input voltage. Overtemperature Protection To provide over temperature protection in a fault condition, the unit relies upon the thermal protection feature of the controller IC. The unit will shut down if the thermal reference point Tref, exceeds the specified maximum temperature threshold, but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restart after it cools down. During a logic-high, the maximum Von/off generated by the power module is 15 V. The maximum allowable October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 7 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Feature Descriptions (continued) Output Voltage Programming Over Voltage Protection Trimming allows the user to increase or decrease the output voltage set point of a module. This is accomplished by connecting an external resistor between the TRIM pin and either the SENSE(+) or SENSE(-) pins. A resistor placed between the Trim pin and Sense (+) increases the output voltage and a resistor placed between the Trim pin and Sense (-) decreases the output voltage. Figure 12 shows the circuit configuration using an external resistor. The trim resistor should be positioned close to the module. If the trim pin is not used then the pin shall be left open. The output overvoltage protection clamp consists of control circuitry, independent of the primary regulation loop, which monitors the voltage on the output terminals. This control loop has a higher voltage set point than the primary loop (See the overvoltage clamp values in the Feature Specifications). In a fault condition, the overvoltage clamp ensures that the output voltage does not exceed Vo, clamp(max). This provides a redundant voltage-control that reduces the risk of output overvoltage. Remote sense Remote sense minimizes the effects of distribution losses by regulating the voltage at the remote-sense connections (See Figure 11). The voltage between the remote-sense pins and the output terminals must not exceed the output voltage sense range given in the Feature Specifications table: VIN(+) The amount of power delivered by the module is defined as the voltage at the output terminals multiplied by the output current. When using remote sense and trim, the output voltage of the module can be increased, which, at the same output current, would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power (Maximum rated power = Vo,set x Io,max). Rtrim-up ON/OFF LOAD TRIM Rtrim-down [VO(+) - VO(-)] - [SENSE(+) - SENSE(-)] 10% of VO,rated The voltage between the VO(+) and VO(-) terminals must not exceed the minimum output overvoltage shutdown value indicated in the Feature Specifications table. This limit includes any increase in voltage due to remotesense compensation and output voltage setpoint adjustment (trim) (see Figure 11). If not using the remote-sense feature to regulate the output at the point of load, then connect SENSE(+) to VO(+) and SENSE(-) to VO(-) at the module. VO(+) SENSE (+) VIN(-) SENSE (-) VO(-) Figure 12. Circuit Configuration to program output voltage using an external resistor. The following equations determine the required external resistor value to obtain a percentage output voltage change of %. To decrease output voltage set point: 510 Rtrim down 10.2 K % Where, % Vo , nom Vdesired 100 Vo , nom Vdesired = Desired output voltage set point (V). SENSE(+) To increase the output voltage set point SENSE(-) SUPPLY VI(+) VO(+) VI(-) VO(-) II CONTACT RESISTANCE IO LOAD CONTACT AND DISTRIBUTION LOSSE Figure 11. Circuit Configuration to program output voltage using external resistor. October 5, 2015 5.1*Vo , nom * 100 % 510 Rtrim up 10.2 K 1.225 * % % Although the output voltage can be increased by both the remote sense and by the trim, the maximum increase for the output voltage is not the sum of both. The maximum increase is the larger of either the remote sense or the trim. (c)2012 General Electric Company. All rights reserved. Page 8 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Thermal Considerations The power modules operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation of the unit. Heat-dissipation components are mounted on the topside of the module. Heat is removed by conduction, convection and radiation to the surrounding environment. Proper cooling can be verified by measuring the temperature of selected components on the topside of the power module. Peak temperature can occur at any to these positions indicated in the following figure 14. 25.4_ (1.0) Wind Tunnel PWBs Power Module Please refer to the Application Note "Thermal Characterization Process For Open-Frame BoardMounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. Heat Transfer via Convection Increased airflow over the module enhances the heat transfer via convection. Thermal derating curves showing the maximum output current that can be delivered by the module versus local ambient temperature (TA) for natural convection, 0.5m/s (100 ft./min) and 1.0 m/s (200 ft./min) are shown in Fig. 15 for the bare module and in Fig. 16 for the module with baseplate. Note that the natural convection condition was measured at 0.05m/s to 0.1m/s (10ft./min. to 20ft./min.); however, systems in which these power modules may be used typically generate natural convection airflow rates of 0.3m/s (60 ft./min.) due to other heat dissipating components in the system. 30 25 20 76.2_ (3.0) 15 x 6.55_ (0.258) Probe Location for measuring airflow and ambient temperature NC 0.5 m/s (100 lfm) 1.0 m/s (200 lfm) 10 5 0 20 Air flow 30 40 50 60 70 80 90 Figure 15. Thermal Derating Curves for the QPW025A0F41 module at 48Vin. Airflow is in the transverse direction (Vin to Vin+). Figure 13. Thermal Test Set up. The temperature at any one of these locations should not exceed 115 C to ensure reliable operation of the power module. The output power of the module should not exceed the rated power for the module as listed in the Ordering Information table. 30 25 20 NC 15 0.5 m/s (100 lfm) 10 5 0 20 Airflow 30 40 50 60 70 80 90 Figure 16. Thermal Derating Curves for the QPW025A0F41H baseplate module at 48Vin. Airflow is in the transverse direction (Vin to Vin+). Thermocouple Location Tref=115o C BC Figure 14. Tref Temperature measurement location. October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 9 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Mechanical Outline Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] TOP VIEW SIDE VIEW BOTTOM VIEW -Optional pin October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 10 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Mechanical Outline for module with base plate. Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] TOP VIEW SIDE VIEW BOTTOM VIEW -Optional pin October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 11 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) (unless otherwise indicated) x.xx mm 0.25 mm (x.xxx in 0.010 in.) 1.57 (0.062) DIA PIN, 2 PLCS 1.02 (0.040) DIA PIN, 7 PLCS - Option October 5, 2015 (c)2012 General Electric Company. All rights reserved. Page 12 GE Data Sheet QPW025A0F41/QPW025A0F41-H DC-DC Power Module 36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 3. Device Code Input Voltage Output Voltage Output Current Efficiency Connector Type 36 - 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F41-H 36 - 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F641-H CC109155280 36 - 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F641-HZ CC109165461 Product codes Comcodes 108993572 Table 2. Device Options Option Device Code Suffix Negative Logic Remote On/Off 1 Auto-restart after fault shutdown Pin Length: 3.68 mm 0.25 mm (0.145 in. 0.010 in.) 4 6 Case pin (only available with -H option) 7 Base plate version for heat sink attachment -H RoHS 6/6 Compliance Z Contact Us For more information, call us at USA/Canada: +1 877 546 3243, or +1 972 244 9288 Asia-Pacific: +86.021.54279977*808 Europe, Middle-East and Africa: +49.89.878067-280 www.gecriticalpower.com GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. October 5, 2015 (c)2012 General Electric Company. All International rights reserved. Version 2.0