GE Data Sheet
October 5, 2015 ©2012 General Electric Company. All rights reserved.
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
Features
Compliant to RoHS EU Directive 2011/65/EU (Z versions)
Compliant to RoHS EU Directive 2011/65/EU under
exemption 7b (Lead solder exemption). Exemption 7b
will expire after June 1, 2016 at which time this produc
twill no longer be RoHS compliant (non-Z versions)
Delivers up to 25A Output current
High efficiency – 92.5% at 3.3V full load
Industry standard Quarter brick footprint
57.9mm x 36.8mm x 12.7mm (with base plate)
(2.28in x 1.45in x 0.5in)
Low output ripple and noise
2:1 Input voltage
Input under voltage protection
Output overcurrent/voltage protection
Over-temperature protection
Tightly regulated output
Remote sense
Adjustable output voltage (+10%/ -20%)
Negative logic, Remote On/Off
Auto restart after fault protection shutdown
Wide operating temperature range (-40°C to 85°C)
Meets the voltage insulation requirements for ETSI 300-
132-2 and complies with and is Licensed for Basic
Insulation rating per EN 60950
CE mark meets the 2006/95/EC directive§
UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03
Certified, and VDE 0805 (EN60950 3rd Edition) Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Applications
Wireless Networks
Optical and Access Network Equipment
Enterprise Networks
Latest generation IC’s (DSP, FPGA, ASIC) and
Microprocessor powered applications
Options
Negative Remote On/Off Logic
Auto-restart from Output overcurrent/voltage
and Over-temperature Protections
Heat plate version (-H)
Description
The QPW025A0F41 is a new open-frame DC/DC power module designed to provide up to 25A output current in an
industry standard quarter brick package. The converter uses synchronous rectification technology and open-frame
packaging techniques to achieve high efficiency reaching 92.5% at 3.3V full load.
* UL is a registered trademark of Underwriters Laboratories, Inc.
CSA is a registered trademark of Canadian Standards Association.
VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
§ This product is intended for integration into end-user equipment. All of the required procedures of end-use equipment should be followed.
** ISO is a registered trademark of the International Organization of Standards
RoHS Compliant
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute
stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those
given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can
adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage
Continuous All VIN - 80 Vdc
Transient (100 ms) VIN, trans - 100 Vdc
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
I/O Isolation All 1500 Vdc
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage All VIN 36 48 75 Vdc
Maximum Input Current
(VIN=0 to VIN, max , Vo = Vo,set, IO=IO, max ) All IIN,max - 2.9
Adc
Quiescent Input Current
Remote on / off disabled (VIN = VIN, nom) All IIN, Q - 5
mA
Idle Input Current
Remote on / off enabled (VIN = VIN, nom, Io = 0 A) All IIN, Idle - 60 - mA
Inrush Transient All I2t - 1 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 12μH source impedance;
Ta 25oC, Cin = TBD)
All - 16 - mAp-p
Input Ripple Rejection (100 - 120Hz) All - 60 - dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part
of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve
maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with
a maximum rating of 6A (see Safety Considerations section). Based on the information provided in this data sheet on inrush
energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse
manufacturer’s data sheet for further information.
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 3
Electrical Specifications (continued)
Parameter Symbol Min Typ Max Unit
Output Voltage Set-point VO, set 3.24 3.3 3.36 % VO, set
(VIN=VIN,nom, IO=IO, max, Tref=25°C) -1.6 +1.6 % VO, set
Output Voltage VO 3.2 - 3.4 % VO
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Output Regulation
Line (VIN = VIN, min to VIN, max)
0.05 0.2 % VO, nom
Load (IO = IO, min to IO, max)
0.05 0.2 % VO, nom
Temperature (Tref =TA, min to TA, max)
0.15 0.50
% VO, nom
Output Ripple and Noise on nominal output
(VIN =VIN, nom and IO = IO, min to IO, max,
Cout = 1μF ceramic // 10μF Tantalum capacitor)
RMS (5Hz to 20MHz bandwidth) 10 20 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) 45 60
mVpk-pk
External Capacitance CO 0 10000 μF
Output Current Io 0 25 A dc
Output Current Limit Inception (Hiccup Mode)
(Vo = 90% Vo, set ) IO, lim 105 120 130
% Io, max
Output Short-Circuit Current IO, s/c 130 150 % Io, max
VO 250 mV @ 25o C
Efficiency
VIN= 48V, TA=25°C, IO= IO, max A η 92.5 %
Switching Frequency fsw 300 KHz
Dynamic Load Response
(dIO/dt=0.1A/s; VIN=VIN, nom; TA=25°C)
Load change from IO = 50% to 75% of IO, max
Peak Deviation Vpk 5 % VO
Settling Time (VO<10% peak deviation) ts 150 s
Load change from IO = 50% to 25% of IO, max,
Peak Deviation Vpk 5 % VO
Settling Time (VO<10% peak deviation) ts 150 s
Isolation Specifications
Parameter Symbol Min Typ Max Unit
Isolation Capacitance CISO 2700 pF
Isolation Resistance RISO 10 M
General Specifications
Parameter Symbol Min Typ Max Unit
Calculated Reliability based upon Telcordia SR-332,
Issue 2; Method I Case 3 (IO= 80% of IO, max, TA=40°C,
airflow = 200 lfm, 90% confidence)
MTBF
FIT
2,808,445
356
Hours
109/Hours
Weight 31 (1.1) g (oz.)
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 4
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
See Feature Descriptions for additional information.
Parameter Symbol Min Typ Max Unit
On/Off Signal interface
(VI = VI,min to VI, max; Open collector or equivalent
Compatible, signal referenced to VI (-) terminal
Logic High (Module ON)
Input High Voltage VIH 7 15 V
Input High Current IIH 50 μA
Logic Low (Module OFF)
Input Low Voltage VIL 0 1.2 V
Input Low Current IIL1 mA
Turn-On Delay and Rise Times
(IO=80% IO, max , VIN=VIN, nom, TA = 25 oC)
Case 1: On/Off input is set to Logic High (Module ON) and
then input power is applied (delay from instant at which VIN
= VIN, min until Vo=10% of Vo,set)
Tdelay 5 msec
Case 2: Input power is applied for at least one second and
then the On/Off input is set to logic high (delay from instant
at which Von/Off=0.9V until Vo=10% of Vo, set)
Tdelay 2.5 msec
Output voltage Rise time (time for Vo to rise from 10% of Vo,
set to 90% of Vo, set) Trise — 4 msec
Output Voltage Remote Sense — —
10 % VO, set
Output voltage overshoot – Startup 1
% VO, set
IO= 80% of IO, max; TA = 25oC
Over temperature Protection
Tref 115 °C
(See Thermal Considerations section)
Input Undervoltage Lockout VUVLO
Turn-on Threshold 34.5 36 V
Turn-off Threshold 30 31.5
V
Hysteresis 3
Output voltage adjustment range(TRIM) 80 110 % VO, set
Over voltage protection 3.8 4.6 Vdc
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 5
Characteristic Curves
The following figures provide typical characteristics for QPW025A0F41/QPW025A0F41-H at 25O C
INPUT CURRENT,(A)
0
0.5
1
1.5
2
2.5
3
30 40 50 60 70
Io = 25.0A
Io = 12.5A
Io = 0.0A
O
N
OFF VOLTAGE OUTPU
VOLTAGE
VOn/Off (V) (5V/div) Vo(V) (1V/div)
INPUT VOLTAGE, VIN (V) TIME, t (2 ms/div)
Figure 1. Typical Start-Up (Input Current) characteristics
at room temperature.
Figure 4. Typical Start-Up Characteristics from Remote
ON/OFF.
EFFICIENCY (%)
70
75
80
85
90
95
0 5 10 15 20 25
Vi n = 75V
Vi n = 48V
Vin = 36V
OUTPUT CURRENT OUTPUT VOLTAGE
IO (A) (5A/div) VO, (V) (200mV/div)
OUTPUT CURRENT, Io (A) TIME, t (100s/div)
Figure 2. Converter Efficiency Vs Load at Vo= 3.3 V.
Figure 5. Transient Response to Dynamic Load Change from
50% to 25% to 50% of full load current.
OUTPUT VOLTAGE
VO (V) (20mV/div)
OUTPUT CURRENT OUTPUT VOLTAGE
IO (A) (5A/div) VO (V) (200mV/div)
TIME, t (2s/div) TIME, t (100s/div)
Figure 3. Typical Output Ripple and Noise
at Vin =48Vdc.
Figure 6. Transient Response to Dynamic Load Change from
75% to 50 % to 75% of full load current.
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 6
Test Configurations
TO OSCILLOSCOPE
12 µH
C
S
220 µF
ESR < 0.1 W
@ 20 °C, 100 kHz
V
I
(+)
V
I
(-)
BATTER
Y
33 µF
CURRENT
PROBE
L
TEST
ESR < 0.7 W
@ 100 kHz
Note: Input reflected-ripple current is measured with the simulated
source inductance of 1uH. Capacitor Cs offsets possible battery
impedance. Current is measured at the input of the module
Figure 7. Input Reflected Ripple Current Test Setup.
V
O
(+)
V
O
(–)
1.0 µF
RESISTI
V
LOAD
SCOPE
CO
PPER
S
TRIP
GROUND PLANE
10 µF
Note: Use a 10uF tantalum and a 1uF ceramic capacitor. Scope
measurement should be made using BNC socket. Position the load
between 51 mm and 76mm (2 in. and 3 in.) from the module
Figure 8. Output Ripple and Noise Test Setup.
V
I
(+)
I
I
I
O
SUPPLY
CONTACT
CONTACT AND
LOAD
SENSE(+)
V
I
(–)
V
O
(+)
V
O
(–)
SENSE(–)
RESISTANCE
DISTRIBUTION L OSSE
S
Figure 9. Output Voltage and Efficiency Test Setup.
= VO. IO
VIN. IIN x 100 %
Efficiency
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 7, a 33 µF
electrolytic capacitor (ESR < 0.7 at 100 kHz) mounted
close to the power module helps ensure stability of the
unit. Consult the factory for further application
guidelines.
Output Capacitance
High output current transient rate of change (high
di/dt) loads may require high values of output
capacitance to supply the instantaneous energy
requirement to the load. To minimize the output
voltage transient drop during this transient, low E.S.R.
(equivalent series resistance) capacitors may be
required, since a high E.S.R. will produce a
correspondingly higher voltage drop during the current
transient.
Output capacitance and load impedance interact with
the power module’s output voltage regulation control
system and may produce an ’unstable’ output
condition for the required values of capacitance and
E.S.R. Minimum and maximum values of output
capacitance and of the capacitor’s associated E.S.R.
may be dictated, depending on the module’s control
system.
The process of determining the acceptable values of
capacitance and E.S.R. is complex and is load-
dependant. GE provides Web-based tools to assist the
power module end-user in appraising and adjusting
the effect of various load conditions and output
capacitances on specific power modules for various
load conditions
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and
separation requirements of the end-use safety agency
standard, i.e., UL60950-1, CSA C22.2 No. 60950-1-03,
EN60950-1 and VDE 0805:2001-12.
For end products connected to –48V dc, or –60Vdc
nominal DC MAINS (i.e. central office dc battery plant),
no further fault testing is required. For all input
voltages, other than DC MAINS, where the input
voltage is less than 60V dc, if the input meets all of the
requirements for SELV, then:
The output may be considered SELV. Output
voltages will remain within SELV limits even with
internally-generated non-SELV voltages. Single
component failure and fault tests were performed
in the power converters.
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 7
One pole of the input and one pole of the output
are to be grounded, or both circuits are to be kept
floating, to maintain the output voltage to ground
voltage within ELV or SELV limits.
For all input sources, other than DC MAINS, where the
input voltage is between 60 and 75V dc (Classified as
TNV-2 in Europe), the following must be meet, if the
converter’s output is to be evaluated for SELV:
The input source is to be provided with reinforced
insulation from any hazardous voltage, including
the ac mains.
One Vi pin and one Vo pin are to be reliably
earthed, or both the input and output pins are to
be kept floating.
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies,
on the combination of supply source and the
subject module to verify that under a single fault,
hazardous voltages do not appear at the module’s
output.
The power module has ELV (extra-low voltage) outputs
when all inputs are ELV.
All flammable materials used in the manufacturing of
these modules are rated 94V-0, or tested to the
UL60950 A.2 for reduced thickness.
The input to these units is to be provided with a
maximum 6A fast-acting (or time-delay) fuse in the
unearthed lead.
Feature Descriptions
Remote On/Off
Two remote On/Off logic options are available. Positive
logic remote On/Off turns the module ON during a
logic-high voltage on the remote On/Off pin, and turns
the module OFF during a logic-low. Negative logic
remote On/Off turns the module OFF during a logic-
high and turns the module ON during logic-low.
Negative logic is specified by suffix “1” at the end of the
device code.
To turn the power module on and off, the user must
supply a switch to control the voltage between the
ON/OFF pin and the VIN(–) terminal (Von/Off). The switch
may be an open collector or equivalent (see Figure 10).
A logic-low is Von/off = 0 V to 1.2V. The maximum Ion/off
during a logic low is 1 mA. The switch should maintain
a logic-low voltage while sinking 1 mA.
During a logic-high, the maximum Von/off generated
by the power module is 15 V. The maximum allowable
leakage current of the switch is 50 µA. If not using the
remote on/off feature, do one of the following:
For positive logic, leave the ON/OFF pin open.
For negative logic, short the ON/OFF pin to VIN(–).
SENSE(+)
VO(+)
SENSE(–)
VO(–)
VI(-)
+
Ion/off ON/OFF
VI(+)
LOA
D
Von/off
Figure 10. Circuit configuration for using Remote
On/Off Implementation.
Overcurrent Protection
To provide protection in a fault (output overload) condi-
tion, the module is equipped with internal current-limit-
ing circuitry, and can endure current limiting
continuously. At the instance of current-limit inception,
the output current begins to tail-out. When an
overcurrent condition exists beyond a few seconds, the
module enters a “hiccup” mode of operation, whereby
it shuts down and automatically attempts to restart..
While the fault condition exists, the module will remain
in this hiccup mode, and can remain in this mode until
the fault is cleared. The unit operates normally once
the output current is reduced back into its specified
range.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, the module operation is disabled. The module will
begin to operate at an input voltage between the
undervoltage lockout limit and the minimum operating
input voltage.
Overtemperature Protection
To provide over temperature protection in a fault
condition, the unit relies upon the thermal protection
feature of the controller IC. The unit will shut down if
the thermal reference point Tref, exceeds the specified
maximum temperature threshold, but the thermal
shutdown is not intended as a guarantee that the unit
will survive temperatures beyond its rating. The
module will automatically restart after it cools down.
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 8
Feature Descriptions (continued)
Over Voltage Protection
The output overvoltage protection clamp consists of
control circuitry, independent of the primary regulation
loop, which monitors the voltage on the output
terminals. This control loop has a higher voltage set
point than the primary loop (See the overvoltage clamp
values in the Feature Specifications). In a fault
condition, the overvoltage clamp ensures that the
output voltage does not exceed Vo, clamp(max). This
provides a redundant voltage-control that reduces the
risk of output overvoltage.
Remote sense
Remote sense minimizes the effects of distribution
losses by regulating the voltage at the remote-sense
connections (See Figure 11). The voltage between the
remote-sense pins and the output terminals must not
exceed the output voltage sense range given in the
Feature Specifications table:
[VO(+) – VO(–)] – [SENSE(+) – SENSE(–)] 10% of VO,rated
The voltage between the VO(+) and VO(–) terminals must
not exceed the minimum output overvoltage shutdown
value indicated in the Feature Specifications table. This
limit includes any increase in voltage due to remote-
sense compensation and output voltage setpoint
adjustment (trim) (see Figure 11). If not using the
remote-sense feature to regulate the output at the
point of load, then connect SENSE(+) to VO(+) and
SENSE() to VO() at the module.
The amount of power delivered by the module is
defined as the voltage at the output terminals
multiplied by the output current. When using remote
sense and trim, the output voltage of the module can
be increased, which, at the same output current, would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power (Maximum rated power = Vo,set x Io,max).
V
O
(+)
SENSE(+)
SENSE(–)
V
O
(–)
V
I
(+)
V
I
(-)
I
O
LOAD
CONTACT AND
DISTRIBUTION LOSS
E
SUPPLY I
I
CONTACT
RESISTANCE
Figure 11. Circuit Configuration to program output
voltage using external resistor.
Output Voltage Programming
Trimming allows the user to increase or decrease the
output voltage set point of a module. This is
accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(-) pins. A resistor placed between the Trim pin
and Sense (+) increases the output voltage and a
resistor placed between the Trim pin and Sense (-)
decreases the output voltage. Figure 12 shows the
circuit configuration using an external resistor. The trim
resistor should be positioned close to the module. If the
trim pin is not used then the pin shall be left open.
V
O
(+)
TRIM
V
O
(-)
R
trim-down
LOAD
V
IN
(+)
ON/OFF
V
IN
(-)
R
trim-up
SENSE (+)
SENSE (-)
Figure 12. Circuit Configuration to program output
voltage using an external resistor.
The following equations determine the required
external resistor value to obtain a percentage output
voltage change of %.
To decrease output voltage set point:
KR downtrim 2.10
%
510
Where,
100% ,
,
nomo
desirednomo
VVV
Vdesired = Desired output voltage set point (V).
To increase the output voltage set point
K
V
Rnomo
uptrim 2.10
%
510
%*225.1 %100**1.5 ,
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim.
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 9
Thermal Considerations
The power modules operate in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation of the unit.
Heat-dissipation components are mounted on the
topside of the module. Heat is removed by conduction,
convection and radiation to the surrounding
environment. Proper cooling can be verified by
measuring the temperature of selected components
on the topside of the power module. Peak temperature
can occur at any to these positions indicated in the
following figure 14.
A
ir
flo w
x
Pow er Modu le
W
ind Tunnel
PWBs
6.55_
(0.258)
76.2_
(3.0)
Probe Location
for m e asur ing
airflow and
ambient
temperature
25.4_
(1.0)
Figure 13. Thermal Test Set up.
The temperature at any one of these locations should
not exceed 115 °C to ensure reliable operation of the
power module. The output power of the module should
not exceed the rated power for the module as listed in
the Ordering Information table.
Airflow
Thermocouple Location Tref=115o C BC
Figure 14. Tref Temperature measurement location.
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-
Mounted Power Modules” for a detailed discussion of
thermal aspects including maximum device
temperatures.
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Thermal derating curves
showing the maximum output current that can be
delivered by the module versus local ambient
temperature (TA) for natural convection, 0.5m/s (100
ft./min) and 1.0 m/s (200 ft./min) are shown in Fig. 15
for the bare module and in Fig. 16 for the module with
baseplate.
Note that the natural convection condition was
measured at 0.05m/s to 0.1m/s (10ft./min. to
20ft./min.); however, systems in which these power
modules may be used typically generate natural
convection airflow rates of 0.3m/s (60 ft./min.) due to
other heat dissipating components in the system.
0
5
10
15
20
25
30
20 30 40 50 60 70 80 90
0. 5 m /s
( 100 lfm) 1. 0 m / s
( 200 lfm)
NC
Figure 15. Thermal Derating Curves for the QPW025A0F41
module at 48Vin. Airflow is in the transverse direction (Vin
to Vin+).
0
5
10
15
20
25
30
20 30 40 50 60 70 80 90
0. 5 m/s
(100 lfm)
NC
Figure 16. Thermal Derating Curves for the QPW025A0F41-
H baseplate module at 48Vin. Airflow is in the transverse
direction (Vin to Vin+).
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 10
Mechanical Outline
Dimensions are in millimeters and [inches].
Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (unless otherwise indicated)
x.xx mm 0.25 mm [x.xxx in 0.010 in.]
TOP VIEW
SIDE VIEW
BOTTOM
VIEW
† -Optional pin
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 11
Mechanical Outline for module with base plate.
Dimensions are in millimeters and [inches].
Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (unless otherwise indicated)
x.xx mm 0.25 mm [x.xxx in 0.010 in.]
TOP VIEW
SIDE VIEW
BOTTOM
VIEW
† -Optional pin
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 12
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) (unless otherwise indicated)
x.xx mm 0.25 mm (x.xxx in 0.010 in.)
† - Option
1.02 (0.040) DIA PIN, 7 PLCS
1.57 (0.062) DIA PIN, 2 PLCS
GE Data Sheet
QPW025A0F41/QPW025A0F41-H DC-DC Power Module
36-75Vdc Input; 3.3Vdc Output Voltage; 25A Output Current
Contact Us
For more information, call us at
USA/Canada:
+1 877 546 3243, or +1 972 244 9288
Asia-Pacific:
+86.021.54279977*808
Europe, Middle-East and Africa:
+49.89.878067-280
www.gecriticalpower.com
GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no
liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
October 5, 2015 ©2012 General Electric Company. All International rights reserved. Version 2.0
Ordering Information
Please contact your GE Sales Representative for pricing, availability and optional features.
Table 3. Device Code
Input Voltage Output
Voltage
Output
Current
Efficiency
Connector
Type Product codes Comcodes
36 – 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F41-H 108993572
36 – 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F641-H CC109155280
36 – 75Vdc 3.3 V 25A 92.5% Through-Hole QPW025A0F641-HZ CC109165461
Table 2. Device Options
Option Device Code Suffix
Negative Logic Remote On/Off 1
Auto-restart after fault shutdown 4
Pin Length: 3.68 mm ± 0.25 mm (0.145 in. ± 0.010 in.) 6
Case pin (only available with –H option) 7
Base plate version for heat sink attachment -H
RoHS 6/6 Compliance Z