2.5 V/3.0 V High Precision Reference AD780 Pin programmable 2.5 V or 3.0 V output Ultralow drift: 3 ppm/C max High accuracy: 2.5 V or 3.0 V 1 mV max Low noise: 100 nV/Hz Noise reduction capability Low quiescent current: 1 mA max Output trim capability Plug-in upgrade for present references Temperature output pin Series or shunt mode operation (2.5 V, 3.0 V) FUNCTIONAL BLOCK DIAGRAM +VIN NC 2 7 AD780 R10 R11 NC 1 6 VOUT 5 TRIM R13 Q6 Q7 R16 R5 R14 TEMP 3 R15 R4 4 GND NC = NO CONNECT 8 O/P SELECT 2.5V - NC 3.0V - GND 00841-001 FEATURES Figure 1. PRODUCT DESCRIPTION The AD780 is an ultrahigh precision band gap reference voltage that provides a 2.5 V or 3.0 V output from inputs between 4.0 V and 36 V. Low initial error and temperature drift combined with low output noise and the ability to drive any value of capacitance make the AD780 the ideal choice for enhancing the performance of high resolution ADCs and DACs, and for any general-purpose precision reference application. A unique low headroom design facilitates a 3.0 V output from a 5.0 V 10% input, providing a 20% boost to the dynamic range of an ADC over performance with existing 2.5 V references. The AD780 can be used to source or sink up to 10 mA, and can be used in series or shunt mode, thus allowing positive or negative output voltages without external components. This makes it suitable for virtually any high performance reference application. Unlike some competing references, the AD780 has no region of possible instability. The part is stable under all load conditions when a 1 F bypass capacitor is used on the supply. A temperature output pin on the AD780 provides an output voltage that varies linearly with temperature, allowing the part to be configured as a temperature transducer while providing a stable 2.5 V or 3.0 V output. The AD780 is a pin compatible performance upgrade for the LT1019(A)-2.5 and the AD680. The latter is targeted toward low power applications. The AD780 is available in three grades in PDIP and SOIC packages. The AD780AN, AD780AR, AD780BN, AD780BR, and AD780CR are specified for operation from -40C to +85C. PRODUCT HIGHLIGHTS 1. The AD780 provides a pin programmable 2.5 V or 3.0 V output from a 4 V to 36 V input. 2. Laser trimming of both initial accuracy and temperature coefficients results in low errors over temperature without the use of external components. The AD780BN has a maximum variation of 0.9 mV from -40C to +85C. 3. For applications that require even higher accuracy, an optional fine-trim connection is provided. 4. The AD780 noise is extremely low, typically 4 mV p-p from 0.1 Hz to 10 Hz and a wideband spectral noise density of typically 100 nV/Hz. This can be further reduced, if desired, by using two external capacitors. 5. The temperature output pin enables the AD780 to be configured as a temperature transducer while providing a stable output reference. Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved. AD780 TABLE OF CONTENTS Specifications..................................................................................... 3 Supply Current Over Temperature .............................................8 Absolute Maximum Ratings............................................................ 4 Turn-On Time ...............................................................................8 Notes............................................................................................... 4 Dynamic Performance..................................................................8 ESD Caution.................................................................................. 4 Line Regulation..............................................................................9 Theory of Operation ........................................................................ 5 Precision Reference for High Resolution 5 V Data Converters ..........................................................................................................9 Applying the AD780......................................................................... 6 Noise Performance ....................................................................... 6 Noise Comparison........................................................................ 7 Temperature Performance........................................................... 7 Temperature Output Pin ............................................................. 7 4.5 V Reference from 5 V Supply ............................................. 10 Negative (-2.5 V) Reference ..................................................... 10 Outline Dimensions ....................................................................... 11 Ordering Guide............................................................................... 12 Temperature Transducer Circuit ................................................ 8 REVISION HISTORY 5/04--Data Sheet Changed from Rev. D to Rev. E Updated Format.................................................................. Universal Changes to Temperature Transducer Circuit section ...................8 Changes to Ordering Guide ...........................................................12 1/04--Data Sheet Changed from Rev. C to Rev. D. Changes to SPECIFICATIONS........................................................2 Updated ORDERING GUIDE.........................................................3 Updated OUTLINE DIMENSIONS .............................................10 5/02--Data Sheet Changed from Rev. B to Rev. C. Updates to packages ............................................................................10 Rev. E | Page 2 of 12 AD780 SPECIFICATIONS TA = 25C, VIN = 5 V, unless otherwise noted. Table 1. Parameter OUTPUT VOLTAGE 2.5 V Out 3.0 V Out OUTPUT VOLTAGE DRIFT1 -40C to +85C -55C to +125C LINE REGULATION 2.5 V Output, 4 V +VIN 36 V, TMIN to TMAX 3.0 V Output, 4.5 V +VIN 36 V, TMIN to TMAX LOAD REGULATION, SERIES MODE Sourcing 0 mA < IOUT< 10 mA TMIN to TMAX Sinking -10 mA < IOUT< 0 mA -40C to +85C -55C to +125C LOAD REGULATION, SHUNT MODE I < ISHUNT< 10 mA QUIESCENT CURRENT, 2.5 V SERIES MODE2 -40C to +85C -55C to +125C MINIMUM SHUNT CURRENT OUTPUT NOISE 0.1 Hz to 10 Hz Spectral Density, 100 Hz LONG-TERM STABILITY3 TRIM RANGE TEMPERATURE PIN Voltage Output @ 25C Temperature Sensitivity Output Resistance SHORT-CIRCUIT CURRENT TO GROUND TEMPERATURE RANGE Specified Performance (A, B, C) Operating Performance (A, B, C)4 AD780AN/AD780AR Min Typ Max Min 2.495 2.995 2.4985 2.9950 2.505 3.005 0.75 0.8 0.7 -40 -55 2.5015 3.0050 AD780BN/AD780BR Min Typ Max Unit 2.499 2.999 2.501 3.001 V V 7 20 7 20 3 ppm/C ppm/C 10 10 10 10 10 10 V/V V/V 50 75 75 75 150 50 75 75 75 150 50 75 75 75 150 V/mA V/mA V/mA V/mA V/mA 75 75 75 V/mA 1.0 1.3 1.0 mA mA mA 1.0 1.3 1.0 0.75 0.8 0.7 1.0 1.3 1.0 0.75 0.8 0.7 4 100 4 100 4 100 V p-p nV/Hz 20 20 20 ppm/1000 Hr % 4.0 500 AD780CR Typ Max 4.0 560 1.9 3 30 620 500 +85 +125 -40 -55 1 4.0 560 1.9 3 30 620 500 +85 +125 -40 -55 560 1.9 3 30 620 mV mV/C k mA +85 +125 C C Maximum output voltage drift is guaranteed for all packages. 3.0 V mode typically adds 100 A to the quiescent current. Also, Iq increases by 2 A/V above an input voltage of 5 V. 3 The long-term stability specification is noncumulative. The drift in subsequent 1,000 hour periods is significantly lower than in the first 1,000 hour period. 4 The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance outside their specified temperature range. 2 Rev. E | Page 3 of 12 AD780 ABSOLUTE MAXIMUM RATINGS Table 2. GND ESD Classification +VIN GND Output safe for indefinite short to ground and momentary short to VIN. Class 1 (1000 V) Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum specifications for extended periods may affect device reliability. NC 1 +VIN 2 TEMP Values 36 V 36 V 36 V 500 mW -65C to +150C 300C AD780 2.5V/3.0V O/PSELECT 8 (NC OR GND) 7 NC 6 VOUT TOP VIEW GND 4 (Not to Scale) 5 TRIM NC = NO CONNECT 00841-002 TEMP 3 Figure 2. Pin Configuration, 8-Lead PDIP and SOIC Packages TRIM VOUT 2.5V/3.0V O/P SELECT 00841-003 Parameter +VIN to Ground TRIM Pin to Ground TEMP Pin to Ground Power Dissipation (25C) Storage Temperature Lead Temperature (Soldering 10 sec) Output Protection Figure 3. Die Layout NOTES Both VOUT pads should be connected to the output. Die Thickness: The standard thickness of Analog Devices bipolar dice is 24 mil 2 mil. Die Dimensions: The dimensions given have a tolerance of 2 mil. Backing: The standard backside surface is silicon (not plated). Analog Devices does not recommend gold-backed dice for most applications. Edges: A diamond saw is used to separate wafers into dice, thus providing perpendicular edges halfway through the die. In contrast to scribed dice, this technique provides a more uniform die shape and size. The perpendicular edges facilitate handling (such as tweezer pickup), while the uniform shape and size simplify substrate design and die attach. Top Surface: The standard top surface of the die is covered by a layer of glassivation. All areas are covered except bonding pads and scribe lines. Surface Metallization: The metallization to Analog Devices bipolar dice is aluminum. Minimum thickness is 10,000 A. Bonding Pads: All bonding pads have a minimum size of 4.0 mil by 6.0 mil. The passivation windows have a minimum size of 3.6 mil by 5.6 mil. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. E | Page 4 of 12 AD780 THEORY OF OPERATION Band gap references are the high performance solution for low supply voltage and low power voltage reference applications. In this technique, a voltage with a positive temperature coefficient is combined with the negative coefficient of a transistor's Vbe to produce a constant band gap voltage. The output voltage of the AD780 is determined by the configuration of Resistors R13, R14, and R15 in the amplifier's feedback loop. This sets the output to either 2.5 V or 3.0 V, depending on whether R15 (Pin 8) is grounded or not connected. In the AD780, the band gap cell contains two NPN transistors (Q6 and Q7) that differ in emitter area by 12x. The difference in their Vbes produces a PTAT current in R5. This, in turn, produces a PTAT voltage across R4 that, when combined with the Vbe of Q7, produces a voltage (Vbg) that does not vary with temperature. Precision laser trimming of the resistors and other patented circuit techniques are used to further enhance the drift performance. A unique feature of the AD780 is the low headroom design of the high gain amplifier, which produces a precision 3 V output from an input voltage as low as 4.5 V (or 2.5 V from a 4.0 V input). The amplifier design also allows the part to work with +VIN = VOUT when current is forced into the output terminal. This allows the AD780 to work as a 2-terminal shunt regulator, providing a -2.5 V or -3.0 V reference voltage output without external components. +VIN NC 2 7 The PTAT voltage is also used to provide the user with a thermometer output voltage (at Pin 3) that increases at a rate of approximately 2 mV/C. AD780 R10 R11 NC 1 6 VOUT 5 TRIM R13 Q6 Q7 R16 R5 The AD780's NC (Pin 7) is a 20 k resistor to +VIN that is used solely for production test purposes. Users who are currently using the LT1019 self-heater pin (Pin 7) must take into account the different load on the heater supply. R14 TEMP 3 R15 R4 NC = NO CONNECT 8 O/P SELECT 2.5V - NC 3.0V - GND 00841-004 4 GND Figure 4. Schematic Diagram Rev. E | Page 5 of 12 AD780 APPLYING THE AD780 100 A bypass capacitor of 1 F (+VIN to GND) should be used if the load capacitance in the application is expected to be greater than 1 nF. The AD780 in 2.5 V mode typically draws 700 A of Iq at 5 V. This increases by ~2 A/V up to 36 V. 1 2 7 +VIN NC 1 0.1 0.1 VOUT 6 NC 10 00841-006 COMPENSATION CAPACITOR, C2 (nF) The AD780 can be used without any external components to achieve specified performance. If power is supplied to Pin 2 and Pin 4 is grounded, Pin 6 provides a 2.5 V or 3.0 V output depending on whether Pin 8 is left unconnected or grounded. 1 10 LOAD CAPACITOR, C1 (F) AD780 1F RNULL TRIM 5 Figure 6. Compensation and Load Capacitor Combinations R POT TEMP GND O/P SELECT 2.5V - NC 3.0V - GND 4 8 NC = NO CONNECT C1 and C2 also improve the settling performance of the AD780 when subjected to load transients. The improvement in noise performance is shown in Figure 7, Figure 8, Figure 9, and Figure 10. 00841-005 3 100 AMPLIFIER GAIN = 100 Figure 5. Optional Fine-Trim Circuit 100V 1s 100 90 10 0% 00841-007 Initial error can be nulled using a single 25 k potentiometer connected between VOUT, TRIM, and GND. This is a coarse trim with an adjustment range of 4%, and is only included here for compatibility purposes with other references. A fine trim can be implemented by inserting a large value resistor (e.g., 1 M to 5 M) in series with the wiper of the potentiometer (see Figure 5). The trim range, expressed as a fraction of the output, is simply greater than or equal to 2.1 k/RNULL for either the 2.5 V or 3.0 V mode. The external null resistor affects the overall temperature coefficient by a factor equal to the percentage of VOUT nulled. 0.1 TO 10Hz Figure 7. Standalone Noise Performance For example, a 1 mV (0.03%) shift in the output caused by the trim circuit, with a 100 ppm/C null resistor, adds less than 0.06 ppm/C to the output drift (0.03% x 200 ppm/C, since the resistors internal to the AD780 also have temperature coefficients of less than 100 ppm/C). NO AMPLIFIER 20V 10ms 100 90 NOISE PERFORMANCE 10 0% 00841-008 The impressive noise performance of the AD780 can be further improved, if desired, by adding two capacitors: a load capacitor (C1) between the output and ground, and a compensation capacitor (C2) between the TEMP pin and ground. Suitable values are shown in Figure 6. 10Hz TO 10kHz Figure 8. Standalone Noise Performance Rev. E | Page 6 of 12 AD780 2.0 7 +VIN NC 1.6 VOUT 6 NC 1.2 ERROR (mV) AD780 1F TRIM 5 TEMP GND O/P SELECT 2.5V - NC 3.0V - GND 4 8 C2 C1 0.8 0.4 0 00841-009 3 NC = NO CONNECT -0.4 -0.8 -60 Figure 9. Noise Reduction Circuit 00841-011 1 2 -40 -20 NOISE COMPARISON The wideband noise performance of the AD780 can also be expressed in ppm. The typical performance with C1 and C2 is 0.6 ppm; without external capacitors, typical performance is 1.2 ppm. This performance is, respectively, 7x and 3x lower than the specified performance of the LT1019. 0 20 40 60 80 TEMPERATURE (C) 100 120 140 Figure 11. Typical AD780BN Temperature Drift TEMPERATURE OUTPUT PIN The AD780 provides a TEMP output (Pin 3) that varies linearly with temperature. This output can be used to monitor changes in system ambient temperature, and to initiate calibration of the system, if desired. The voltage VTEMP is 560 mV at 25C, and the temperature coefficient is approximately 2 mV/C. NO AMPLIFIER 20V Figure 12 shows the typical VTEMP characteristic curve over temperature taken at the output of the op amp with a noninverting gain of 5. 10ms 100 90 4.25 4.00 CIRCUIT CALIBRATED AT 25C REFER TO FIGURE 13 VOLTAGE (VOUT) 3.75 00841-010 10 0% 3.50 10mV PER C 3.25 3.00 2.75 10Hz TO 10kHz 00841-012 2.50 Figure 10. Reduced Noise Performance with C1 = 100 F, C2 = 100 nF 2.25 TEMPERATURE PERFORMANCE The AD780 provides superior performance over temperature by means of a combination of patented circuit design techniques, precision thin-film resistors, and drift trimming. Temperature performance is specified in terms of ppm/C; because of nonlinearity in the temperature characteristic, the box test method is used to test and specify the part. The nonlinearity takes the form of the characteristic S-shaped curve shown in Figure 11. The box test method forms a rectangular box around this curve, enclosing the maximum and minimum output voltages over the specified temperature range. The specified drift is equal to the slope of the diagonal of this box. 2.00 -75 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 150 Figure 12. Temperature Pin Transfer Characteristic Since the TEMP voltage is acquired from the band gap core circuit, current pulled from this pin has a significant effect on VOUT. Care must be taken to buffer the TEMP output with a suitable op amp, e.g., an OP07, AD820, or AD711 (all of which would result in less than a 100 V change in VOUT). The relationship between ITEMP and VOUT is VOUT = 5.8 mV/A ITEMP (2.5 V Range) or VOUT = 6.9 mV/A ITEMP (3.0 V Range) Rev. E | Page 7 of 12 AD780 Notice how sensitive the current dependent factor on VOUT is. A large amount of current, even in tens of microamp, drawn from the TEMP pin can cause the VOUT and TEMP output to fail. 0.85 -55C The choice of C1 and C2 was dictated primarily by the need for a relatively flat response that rolled off early in the high frequency noise at the output. However, there is considerable margin in the choice of these capacitors. For example, the user can actually put a huge C2 on the TEMP pin with none on the output pin. However, one must either put very little or a lot of capacitance at the TEMP pin. Intermediate values of capacitance can sometimes cause oscillation. In any case, the user should follow the recommendation in Figure 6. +25C 0.75 +125C 0.70 0.65 00841-014 QUIESCENT CURRENT (mA) 0.80 0.60 4 36 INPUT VOLTAGE (V) TEMPERATURE TRANSDUCER CIRCUIT The circuit shown in Figure 13 is a temperature transducer that amplifies the TEMP output voltage by a gain of a little over +5 to provide a wider full-scale output range. The digital potentiometer can be used to adjust the output so it varies by exactly 10 mV/C. To minimize resistance changes with temperature, resistors with low temperature coefficients, such as metal film resistors, should be used. Figure 14. Typical Supply Current over Temperature TURN-ON TIME The time required for the output voltage to reach its final value within a specified error band is defined as the turn-on settling time. The two major factors that affect this are the active circuit settling time and the time for the thermal gradients on the chip to stabilize. Typical settling performance is shown in Figure 15. The AD780 settles to within 0.1% of its final value within 10 s. 5V VIN 2 5V +VIN 0V TEMP 3 1F 10mV/C AD820 AD780 VOUT 2.500V RB 1.27k (1%) RF 6.04k (1%) RBP 200 2.499V 2.498V 00841-015 4 00841-013 GND 10s/DIV Figure 15. Turn-On Settling Time Performance Figure 13. Differential Temperature Transducer SUPPLY CURRENT OVER TEMPERATURE DYNAMIC PERFORMANCE The AD780's quiescent current varies slightly over temperature and input supply range. The test limit is 1 mA over the industrial and 1.3 mA over the military temperature range. Typical performance with input voltage and temperature variation is shown in Figure 14. The output stage of the AD780 has been designed to provide superior static and dynamic load regulation. Figure 16 and Figure 17 show the performance of the AD780 while driving a 0 mA to 10 mA load. Rev. E | Page 8 of 12 AD780 +VIN ILOAD OUTPUT CHANGE (50mV/DIV) 0mA 2 AD780 VOUT 6 1F VOUT 0V VL VOUT (CL = 1000pF) 00841-019 4 00841-016 249 10mA Figure 16. Transient Resistive Load Test Circuit 10s/DIV ILOAD Figure 19. Settling under Dynamic Capacitive Load LINE REGULATION 10mA Line regulation is a measure of change in output voltage due to a specified change in input voltage. It is intended to simulate worst-case unregulated supply conditions and is measured in V/V. Figure 20 shows typical performance with 4.0 V < VIN < 15.0 V. VOUT (CL = 0pF) 200 T = 25C 00841-017 OUTPUT CHANGE (50mV/DIV) 0mA 100 OUTPUT CHANGE (V) 10s/DIV Figure 17. Settling under Transient Resistive Load The dynamic load may be resistive and capacitive. For example, the load may be connected via a long capacitive cable. Figure 18 and Figure 19 show the performance of the AD780 driving a 1000 pF, 0 mA to 10 mA load. 0 -100 00841-020 +VIN -200 4 2 AD780 PRECISION REFERENCE FOR HIGH RESOLUTION 5 V DATA CONVERTERS CL 1000pF 1F VL VOUT 0V 00841-018 249 4 15 Figure 20. Output Voltage Change vs. Input Voltage VOUT 6 10 INPUT VOLTAGE (V) Figure 18. Capacitive Load Transient Response Test Circuit The AD780 is ideally suited to be the reference for most 5 V high resolution ADCs. The AD780 is stable under any capacitive load, has superior dynamic load performance, and its 3.0 V output provides the converter with the maximum dynamic range without requiring an additional and expensive buffer amplifier. One of the many ADCs that the AD780 is suited for is the AD7884, a 16-bit, high speed sampling ADC (see Figure 21). This part previously needed a precision 5 V reference, resistor divider, and buffer amplifier to do this function. Rev. E | Page 9 of 12 AD780 VSUPPLY 5V AD7884 0.1F 2 1k +VIN 2N2907 2 1F VREF + F 6 AD780 OP90 AD780 2 2.5V/3.0V SELECT 4 8 - 6 VOUT 2.5k 4 10F 0.1F 4 0.1F 00841-021 GND VREF + S 7 3 + 6 The AD780 is also ideal for use with higher resolution converters, such as the AD7710/AD7711/AD7712 (see Figure 22. While these parts are specified with a 2.5 V internal reference, the AD780 in 3 V mode can be used to improve the absolute accuracy, temperature stability, and dynamic range. It is shown in Figure 22 with the two optional noise reduction capacitors. 4k 0.01% 5k 0.01% Figure 21. Precision 3 V Reference for the AD7884 16-Bit, High Speed ADC 3.9 00841-023 VOUT Figure 23. 4.5 V Reference from a Single 5 V Supply NEGATIVE (-2.5 V) REFERENCE The AD780 can produce a negative output voltage in shunt mode by connecting the input and output to ground, and connecting the AD780's GND pin to a negative supply via a bias resistor, as shown in Figure 25. 5V AD7710 2 7 +VIN NC 2 +VIN 1 AD780 1F TRIM 5 AD780 3 3 TEMP 100F GND 2.5V/3.0V O/P SELECT 4 8 REF IN- 00841-022 100nF VOUT 6 NC R= Figure 22. Precision 2.5 V or 3.0 V Reference for the AD7710 High Resolution, - ADC GND O/P SELECT 2.5V - NC 3.0V - GND 4 8 -2.5 VOUT NOTES 1. IL = LOAD CURRENT 2. IS MIN = MINIMUM SHUNT CURRENT 3. NC = NO CONNECT VOUT - (V-) IL + IS MIN V- 4.5 V REFERENCE FROM 5 V SUPPLY 00841-024 1F REF IN+ 6 Figure 24. Negative (-2.5 V Shunt Mode Reference) Some 5 V high resolution ADCs can accommodate reference voltages up to 4.5 V. The AD780 can be used to provide a precision 4.5 V reference voltage from a 5 V supply using the circuit shown in Figure 23. This circuit provides a regulated 4.5 V output from a supply voltage as low as 4.7 V. The high quality tantalum 10 F capacitor, in parallel with the ceramic AD780 0.1 F capacitor and the 3.9 resistor, ensures a low output impedance around 50 MHz. A precise -2.5 V reference capable of supplying up to 100 mA to a load can be implemented with the AD780 in series mode, using the bootstrap circuit shown in Figure 25. +5V +VIN 2 1k AD780 OUT 6 8 +5V 4 CONNECT IF -3V OUTPUT DESIRED -2.5V (IL 100mA) - OP07 2N3906 + -5V -5V 1000pF Figure 25. -2.5 V High Load Current Reference Rev. E | Page 10 of 12 00841-025 VOUT AD780 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 8 5 4.00 (0.1574) 3.80 (0.1497) 1 6.20 (0.2440) 4 5.80 (0.2284) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 0.50 (0.0196) x 45 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) COPLANARITY SEATING 0.31 (0.0122) 0.10 PLANE 8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 26. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 0.375 (9.53) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.100 (2.54) BSC 0.015 (0.38) MIN 0.180 (4.57) MAX 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14) 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 27. 8-Lead Plastic Dual-In-Line Package [PDIP] (N-8) Dimensions shown in inches and (millimeters) Rev. E | Page 11 of 12 AD780 ORDERING GUIDE Model AD780AN AD780AR AD780AR-REEL7 AD780ARZ1 AD780BN AD780BR AD780BRZ1 AD780BR-REEL AD780BR-REEL7 AD780BRZ1 AD780BRZ-REEL71 AD780CR AD780CR-REEL7 AD780CRZ1 1 Initial Error 5.0 mV 5.0 mV 5.0 mV 5.0 mV 1.0 mV 1.0 mV 1.0 mV 1.0 mV 1.0 mV 1.0 mV 1.0 mV 1.5 mV 1.5 mV 1.5 mV Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Temperature Coefficient 7 ppm/C 7 ppm/C 7 ppm/C 7 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 7 ppm/C 7 ppm/C 7 ppm/C Z = Pb-free part. (c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00841-0-5/04(E) Rev. E | Page 12 of 12 Package Option PDIP SOIC SOIC SOIC PDIP SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC Qty. per Tube/Reel 48 98 750 98 48 98 98 2,500 750 98 750 98 750 98