DATASHEET ICS525-01/02 USER CONFIGURABLE CLOCK Description Features The ICS525-01/02 are the most flexible way to generate a high-quality, high-accuracy, high-frequency clock output from an inexpensive crystal or clock input. The user can configure the device to produce nearly any output frequency from any input frequency by grounding or floating the select pins. Neither microcontroller, software, nor device programmer are needed to set the frequency. Using Phase-Locked Loop (PLL) techniques, the device accepts a standard fundamental mode, inexpensive crystal to produce output clocks up to 250 MHz. It can also produce a highly accurate output clock from a given input clock, keeping them frequency locked together. * Packaged as 28-pin SSOP (150 mil body) * Industrial and commercial versions available in Pb (lead) free package * User determines the output frequency by setting all * * * * * * * * * * * * For similar capability with a serial interface, use the ICS307. For simple multipliers to produce common frequencies, refer to the ICS50x family of parts, which are smaller and more cost effective. These products are intended for clock generation. They have low output jitter (variation in the output period), but input to output skew and jitter are not defined nor guaranteed. For applications which require defined input to output timing, use the ICS527-01. internal dividers Eliminates need for custom oscillators No software needed Online calculator determines register settings Pull-ups on all select inputs Input crystal frequency of 5 - 27 MHz Input clock frequency of 2 - 50 MHz Very low jitter Duty cycle of 45/55 up to 200 MHz Operating voltage of 3.0 V or 5.5 V Ideal for oscillator replacement Industrial temperature version available For Zero Delay, refer to the ICS527 Block Diagram VDD 2 PD X1/ICLK Crystal or clock input Crystal Oscillator Reference Divider CLK Phase Comparator, Charge Pump, and Loop Filter VCO Output Divider X2 VCO Divider Optional crystal capacitors 7 R6:R0 IDT(R) USER CONFIGURABLE CLOCK 9 V8:V0 1 REF 2 GND 3 S2:S0 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER Pin Assignment R5 1 28 R4 R6 2 27 R3 S0 3 26 R2 S1 4 25 R1 S2 5 24 R0 VDD 6 23 VDD 7 22 REF X2 8 21 CLK GND 9 20 GND V0 10 19 PD V1 11 18 V8 V2 12 17 V7 V3 13 16 V6 V4 14 15 V5 X1/ICLK ICS525-01/-02 Pin Descriptions Pin Number Pin Name Pin Type 1, 2, 24-28 R5, R6, R0-R4 I(PU) Reference divider word input pins determined by user. Forms a binary number from 0 to 127. 3, 4, 5 S0, S1, S2 I(PU) Select pins for output divider determined by user. See table on page 3 6, 23 VDD Power Connect to VDD. 7 X1/ICLK X1 Crystal connection. Connect to a parallel resonant fundamental crystal or input clock. 8 X2 X2 Crystal connection. Connect to a crystal or leave unconnected for clock. 9, 20 GND Power Connect to ground. 10 - 18 V0 - V8 I(PU) VCO divider word input pins determined by user. Forms a binary number from 0 to 511. 19 PD Input Power-down. Active low. Turns off entire chip when low. Clock outputs tri-stated. 21 CLK Output Output clock determined by status of R0-R6, V-V8, S0-S2, and input frequency. 22 REF Output Reference output. Buffered crystal oscillator (or clock ) output. Pin Description KEY: I(PU) = Input with internal pull-up resistor; X1, X2 = crystal connections IDT(R) USER CONFIGURABLE CLOCK 2 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER ICS525-01 Output Frequency and Output Divider Table S2 S1 S0 CLK Output Pin 5 Pin 4 Pin 3 Divider Output Frequency Range (MHz) VDD = 5 V VDD = 3.3 V 0 - 70C -40 to +85C 0 - 70C -40 to +85C 3-26 3-23 3-18 3-16 0 0 0 10 0 0 1 2 15-160 15-140 15-100 15-90 0 1 0 8 3.75-40 3.75-36 3.75-25 3.75-22 0 1 1 4 7.5-80 7.5-72 7.5-50 7.5-45 1 0 0 5 6-50 6-45 6-34 6-30 1 0 1 7 4-40 4-36 4-26 4-23 1 1 0 9 3.3-33.3 3.3-30 3.3-20 3.3-18 1 1 1 6 5-53 5-47 5-27 5-24 ICS525-02 Output Frequency and Output Divider Table S2 S1 S0 CLK Output Pin 5 Pin 4 Pin 3 Divider Output Frequency Range (MHz) VDD = 5 V VDD = 3.3 V -40 to +85C -40 to +85C 5-67 5-40 0 0 0 6 0 0 1 2 15-200 15-120 0 1 0 8 3.75-50 3.75-30 0 1 1 4 7.5-100 7.5-60 1 0 0 5 6-80 6-48 1 0 1 7 4-57 4-34 1 1 0 1 30-250 30-200 1 1 1 3 10-133 10-80 IDT(R) USER CONFIGURABLE CLOCK 3 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER VDW + 8 RDW + 2 OD External Components/Crystal Selection CLK Frequency = Input Frequency 2x --------------------------------------------- Decoupling Capacitors Where: The ICS525-01/02 requries two 0.01F decoupling capacitors to be connected between VDD and GND, one on each side of the chip. The capacitor must be connected close to the device to minimize lead inductance. Reference Divider Word (RDW) = 0 to 127 (0 not permitted for ICS525-01) VCO Divider Word (VDW) = 0 to 511 (0, 1, 2, 3 not permitted for ICS525-01) External Resistors Output Divider (OD) = values on pages 3-4 A 33series termination resistor should be used on the CLK and REF pins. Also, the following operating ranges should be observed: Crystal Load Capacitors 1. The output frequency must be in the ranges listed on pages 3-4. The approximate total on-chip capacitance for a crystal is 16 pF, so a parallel resonant, fundamental mode crystal with this value of load (correlation) capacitance should be used. For crystals with a specified load capacitance greater than 16 pF, crystal capacitors may be connected from each of the pins X1 and X2 to Ground as shown in the block diagram. The value (in pF) of these crystal caps should be (CL -16)*2, where CL is the crystal load capacitance in pF. These external capacitors are only required for applications where the exact frequency is critical. For a clock input, connect to X1 and leave X2 unconnected (no capacitors on either). 2. The phase detector frequency must be above 200 kHz. InputFrequency 200kHz < ---------------------------------------------- RDW + 2 Since all of the inputs have pull-up resistors, it is only necessary to ground the pins that need to be set to zero. Which Part to Use? Determining the Output Frequency The ICS525-01 is the original configurable clock. Users have full control in setting the desired output frequency over the range shown in the tables on pages 3-4. To replace a standard oscillator, users should connect the divider select input pins directly to ground (or VDD, although this is not required because of internal pull-ups) during Printed Circuit Board layout. The ICS525 will automatically produce the correct frequency when all components are soldered. It is also possible to connect the inputs to parallel I/O ports to switch frequencies. By choosing divides carefully, the number of inputs which need to be changed can be minimized. Observe the restrictions on allowed values of VDW and RDW. The ICS525-02 has a higher maximum output grequency and a slightly different set of output dividers. To determine the best combination of VCO, reference, and output divide, use the ICS525 Calculator on our web site. Configuration Pin Settings The output of the ICS525 can be determined by the following simple equation: IDT(R) USER CONFIGURABLE CLOCK 4 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS525-01/02. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature, Commercial 0 to +70C Ambient Operating Temperature, Industrial -40 to +85C Storage Temperature -65C to 150C Junction Temperature 125C Soldering Temperature 260C (max. of 10 seconds) DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V Parameter Symbol Conditions Min. Typ. Units 5.5 V Operating Voltage VDD Operating Supply Current IDD 60 MHz out, no load, 15 MHz crystal, ICS525-01/02 only 8 mA Operating Supply Current, Power-down IDD Pin 19 = 0, Note 1 4 A Input High Voltage VIH Input Low Voltage VIL Input High Voltage, X1/ICLK only VIH ICLK (pin7) Input Low Voltage, X1/ICLK only VIL ICLK (pin7) Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Short Circuit Current 3.0 Max. 2 V 0.8 VDD/2+1 VDD/2 VDD/2 V V VDD/2-1 VDD-0.4 V V 0.4 V CLK and REF outputs 55 mA Input Capacitance CIN V, R, S pins and pin 19 4 pF On-chip Pull-up Resistor RPU V, R, S pins and pin 19 270 k IDT(R) USER CONFIGURABLE CLOCK 5 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V Parameter Input Frequency Symbol FIN Conditions Min. Typ. Max. Units Crystal input 5 27 MHz Clock input 2 50 MHz Output Clock Rise Time 0.8 to 2.0 V 1 ns Output Clock Fall Time 2.0 to 0.8 V 1 ns Output Clock Duty Cycle, OD = 2, 4, 6, 8, or 10 At VDD/2 45 Output Clock Duty Cycle, OD = 3, 5, 7, or 9 At VDD/2 Output Clock Duty Cycle, OD = 1 (-02 only) At VDD/2 49 to 51 55 % 40 60 % 35 65 Power-down Time, PD low to clocks stopped 50 ns Power-up Time, PD high to clocks stable 10 ms Absolute Clock Period Jitter, ICS525-01, Note 2 tja Deviation from mean One Sigma Clock Period Jitter, ICS525-01, Note 2 tjs Absolute Clock Period Jitter, ICS525-02, Note 2 One Sigma Clock Period Jitter, ICS525-02, Note 2 140 ps One Sigma 45 ps tja Deviation from mean 85 ps tjs One Sigma 30 ps NOTE 1: Phase relationship between input and output can change at power-up. For a fixed phase relationship, see the ICS527. NOTE 2: For 16 MHz, 100 MHz output. Use the -02 for lowest jitter. IDT(R) USER CONFIGURABLE CLOCK 6 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER Package Outline and Package Dimensions (28-pin SSOP, 150 mil Body) Package dimensions are kept current with JEDEC Publication No. 95, MO-153 Millimeters Inches* 28 Symbol E1 Min A A1 A2 b C D E E1 e L aaa E INDEX AREA 1 2 D Max 1.35 1.75 0.10 0.25 -1.50 0.20 0.30 0.18 0.25 9.80 10.00 5.80 6.20 3.80 4.00 0.635 Basic 0.40 1.27 0 8 -0.10 Min Max .053 .069 .0040 .010 -.059 .008 .012 .007 .010 .386 .394 .228 .244 .150 .157 0.025 Basic .016 .050 0 8 -0.004 *For reference only. Controlling dimensions in mm. A 2 A A 1 c -Ce b SEATING PLANE L aaa C IDT(R) USER CONFIGURABLE CLOCK 7 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 525-01RLF ICS525-01RLF Tubes 28-pin SSOP 0 to +70C 525-01RLFT ICS525-01RLF Tape and Reel 28-pin SSOP 0 to +70C 525-01RILF ICS525-01RILF Tubes 28-pin SSOP -40 to +85C 525-01RILFT ICS525-01RILF Tape and Reel 28-pin SSOP -40 to +85C 525R-02LF ICS525R-02LF Tubes 28-pin SSOP 0 to +70C 525R-02LFT ICS525R-02LF Tape and Reel 28-pin SSOP 0 to +70C 525R-02ILF ICS525R-02ILF Tubes 28-pin SSOP -40 to +85C 525R-02ILFT ICS525R-02ILF Tape and Reel 28-pin SSOP -40 to +85C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. Revision History Rev. U - removed -11 and -12 references/parts from datasheet. The devices are obsolete. IDT(R) USER CONFIGURABLE CLOCK 8 ICS525-01/02 REV U 033015 ICS525-01/02 USER CONFIGURABLE CLOCK CLOCK MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com (c) 2012 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, ICS, and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA