S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits June 2010 Rev. 2.0.0 GENERAL DESCRIPTION APPLICATIONS The SP706R/S/T and SP708R/S/T series is a family of microprocessor (P) supervisory circuits that integrate myriad components involved in discrete solutions which monitor power-supply and battery in P and digital systems. The SP706R/S/T and SP708R/S/T series will significantly improve system reliability and operational efficiency when compared to solutions obtained with discrete components. The features of the SP706R/S/T and SP708R/S/T series include a watchdog timer, a P reset, a Power Fail Comparator, and a manual-reset input. The SP706R/S/T and SP708R/S/T series is ideal for 3.0V or 3.3V applications in automotive systems, computers, controllers, and intelligent instruments. The SP706R/S/T and SP708R/S/T series is an ideal solution for systems in which critical monitoring of the power supply to the P and related digital components is demanded. * Processors & DSPs Based Systems * Industrial & Medical Instruments FEATURES * Precision Low Voltage Monitor - SP706R/SP708R: +2.63V - SP706S/SP708S: +2.93V - SP706T/SP708T: +3.08V * 200ms RESET Pulse Width - SP706R/S/T: Active Low - SP708R/S/T: Active High and Active Low * Independent Watchdog Timer - 1.6s Timeout (SP706R/S/T) - Enable/Disable Function * 40A Maximum Supply Current * Debounced TTL/CMOS Manual Reset Input * RESET Asserted Down to VCC=1V * VCC Glitch Immunity * Voltage Monitor for Power Failure or Low Battery Warning * 8-Pin NSOIC and MSOP Packages * Pin Compatible with Industry Standards 706R/S/T and 708R/S/T Part Number RESET Threshold RESET Active Manual RESET Watchdog PFI Accuracy SP706R 2.63V Low Yes Yes 4% SP706S 2.93V Low Yes Yes 4% SP706T 3.08V Low Yes Yes 4% SP708R 2.63V Low and High Yes No 4% SP708S 2.93V Low and High Yes No 4% SP708T 3.08V Low and High Yes No 4% Exar Corporation 48720 Kato Road, Fremont CA 94538, USA www.exar.com Tel. +1 510 668-7000 - Fax. +1 510 668-7001 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits ABSOLUTE MAXIMUM RATINGS ESD Rating (HBM - Human Body Model) .................... 2kV Continuous Power Dissipation SO (derate 5.88mW/C above +70C)...............471mW Mini SO (derate 4.10mW/C above +70C) ........330mW Storage Temperature ..............................-65C to 160C Lead Temperature (Soldering, 10 sec) ....................300C These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. VCC .......................................................... -0.3V to 6.0V All Other Inputs (Note 1) ................... -0.3V to (VCC+0.3V) Input Current VCC .................................................................20mA GND ................................................................20mA Output Current (All outputs) ...............................20mA ELECTRICAL SPECIFICATIONS Unless otherwise indicated, VCC = 2.7V to 5.5V (SP70xR), VCC = 3.15V to 5.5V (SP70xS), VCC = 3.0V to 5.5V (SP70xT), TA= TMIN to TMAX, typical at 25C. Parameter Operating Voltage Range VCC Min. Units 5.5 V 40 A 2.55 2.63 2.70 2.85 2.93 3.00 3.00 3.08 3.15 Reset Threshold Hysteresis Reset Pulse Width tRS Max. 25 1.0 Supply Current ISUPPLY Reset Threshold Typ. 200 MR=VCC or floating, WDI floating SP706R. SP708R V SP706S. SP708S SP706T. SP708T mV Note 2 280 ms Note 2 0.3 V 20 140 Conditions RESET Output Voltage VOH VRST(MAX)<VCC<3.6V, ISOURCE=500A 0.8xVCC VOL VOH VRST(MAX)<VCC<3.6V, ISOURCE=215A VCC-0.6 0.3 VOL VOH 4.5V<VCC<5.5V, ISINK=3.2mA 0.4 VOL RESET Output Voltage VOH V VCC-1.5 1.00 WDI Pulse Width tWP (note 1) 50 VRST(MAX)<VCC<3.6V, ISOURCE=1.2mA 4.5V<VCC<5.5V, ISOURCE=800A 4.5V<VCC<5.5V, ISOURCE=3.2mA 0.4 VOL Watchdog Timeout Period tWD VRST(MAX)<VCC<3.6V, ISINK=1.2mA 4.5V<VCC<5.5V, ISOURCE=800A VCC-1.5 1.60 2.25 s VCC<3.6V ns VIL=0.4V, VIH=0.8xVCC V VRST(MAX)<VCC<3.6V WDI Input Threshold 0.7xVCC VCC=5V 0.8 VIL VIH WDI Input Current VRST(MAX)<VCC<3.6V 0.6 VIL VIH VCC=5V 3.5 -1 0.02 1 A 0.3 V WDI=0V or WDI=VCC WDO Output Voltage VIL VRST(MAX)<VCC<3.6V, ISOURCE=500A 0.8xVCC VIH VIL VCC-1.5 (c) 2010 Exar Corporation 4.5V<VCC<5.5V, ISINK=3.2mA 0.4 VIH MR Pull-up Current VRST(MAX)<VCC<3.6V, ISINK=1.2mA 4.5V<VCC<5.5V, ISOURCE=800A 25 70 250 100 250 600 2/16 A MR = 0V, VRST(MAX)<VCC<3.6V MR = 0V, 4.5V<VCC<5.5V Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits Parameter MR Pulse Width tMR Min. Typ. Max. 500 Units ns 150 Conditions VRST(MAX)<VCC<3.6V 4.5V<VCC<5.5V MR Input Threshold 0.6 VIL VIH 0.7xVCC VIL VIH PFI Input Current VRST(MAX)<VCC<3.6V 0.8 4.5V<VCC<5.5V 750 VRST(MAX)<VCC<3.6V 2.0 4.5V<VCC<5.5V MR to Reset Out Delay tMD PFI Input Threshold VRST(MAX)<VCC<3.6V V 250 ns 1.20 1.25 1.30 V -25.00 0.01 25.00 nA 0.3 V 4.5V<VCC<5.5V VCC=3.0V - SP70xR, PFI falling VCC=3.3V - SP70xS/T, PFI falling PFO Output Voltage VIL VIL VRST(MAX)<VCC<3.6V, ISOURCE=500A 0.8xVCC VIH VCC-1.5 VIH VRST(MAX)<VCC<3.6V, ISINK=1.2mA 4.5V<VCC<5.5V, ISOURCE=800A 0.4 4.5V<VCC<5.5V, ISINK=3.2mA Note 1:WDI minimum rise /fall time is 1s. BLOCK DIAGRAM Fig. 1: SP706R/S/T Block Diagram (c) 2010 Exar Corporation 3/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits Fig. 2: SP708R/S/T Block Diagram PIN ASSIGNMENT Fig. 3: Pin Assignment (c) 2010 Exar Corporation 4/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits PIN DESCRIPTION Name Pin Number SP706R/S/T SOIC MSOP MR 1 VCC GND Description SP708R/S/T SOIC MSOP 3 1 3 2 3 4 5 2 3 4 5 PFI 4 6 4 6 PFO 5 7 5 7 WDI 6 8 - - N.C. - - 6 8 RESET 7 1 7 1 WDO 8 2 - - RESET - - 8 2 Manual Reset This input triggers a reset pulse when pulled below 0.8V. This active LOW input has an internal 70A pull-up current. It can be driven from a TTL or CMOS logic line or shorted to ground with a switch. Voltage Input Ground reference for all signals Power-Fail Input When this voltage monitor input is less than 1.25V, PFO goes LOW. Connect PFI to ground or VCC when not in use. Power-Fail Output This output is LOW until PFI is less then 1.25V Watchdog Input If this input remains HIGH or LOW for 1.6s, the internal watchdog timer times out and WDO goes LOW. Floating WDI or connecting WDI to a high-impedance tri-state buffer disables the watchdog feature. The internal watchdog timer clears whenever RESET is asserted, WDI is tri-stated, or whenever WDI sees a rising or falling edge. No Connect Active-LOW RESET Output This output pulses LOW for 200ms when triggered and stays LOW whenever VCC is below the reset threshold. It remains LOW for 200ms after Vcc rises above the reset threshold or MR goes from LOW to HIGH. A watchdog timeout will not trigger RESET unless WDO is connected to MR. Watchdog Output This output pulls LOW when the internal watchdog timer finishes its 1.6s count and does not go HIGH again until the watchdog is cleared. WDO also goes LOW during low-line conditions. Whenever VCC is below the reset threshold, WDO stays LOW. However, unlike RESET, WDO does not have a minimum pulse width. As soon as VCC is above the reset threshold, WDO goes HIGH with no delay. Active-HIGH RESET Output This output is the complement of RESET. Whenever RESET is HIGH, RESET is LOW and vice-versa. Note that the SP708R/S/T has a reset output only. ORDERING INFORMATION Part Number Temperature Range SP706RCN-L 0CTA+70C SP706RCN-L/TR 0CTA+70C SP706RCU-L SP706RCU-L/TR 0CTA+70C 0CTA+70C SP706REN-L -40CTA+85C SP706REN-L/TR -40CTA+85C SP706REU-L -40CTA+85C SP706REU-L/TR -40CTA+85C SP706SCN-L 0CTA+70C SP706SCN-L/TR 0CTA+70C SP706SCU-L 0CTA+70C SP706SCU-L/TR 0CTA+70C (c) 2010 Exar Corporation Marking Package SP706RC YYWWL X 8-pin NSOIC 706R CXXX YWW SP706RE YYWWL X 706R EXXX YWW SP706SC YYWWL X 706S CXXX YWW Packing Quantity Note 1 Bulk Lead 8-pin NSOIC 2.5K/Tape & Reel Lead Bulk 8-pin MSOP Lead 8-pin MSOP 2.5K/Tape & Reel Lead 8-pin NSOIC Bulk Note 2 Free Free Free Free Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk 8-pin MSOP Lead Free 8-pin MSOP 2.5K/Tape & Reel Lead Free Bulk Lead 8-pin NSOIC 2.5K/Tape & Reel Lead Bulk 8-pin MSOP Lead 8-pin MSOP 2.5K/Tape & Reel Lead 8-pin NSOIC 5/16 Free Free Free Free Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits Part Number Temperature Range SP706SEN-L -40CTA+85C SP706SEN-L/TR -40CTA+85C SP706SEU-L -40CTA+85C SP706SEU-L/TR -40CTA+85C SP706TCN-L 0CTA+70C SP706TCN-L/TR 0CTA+70C SP706TCU-L 0CTA+70C SP706TCU-L/TR 0CTA+70C SP706TEN-L -40CTA+85C SP706TEN-L/TR -40CTA+85C SP706TEU-L -40CTA+85C SP706TEU-L/TR -40CTA+85C SP708REN-L -40CTA+85C SP708REN-L/TR -40CTA+85C SP708SCN-L 0CTA+70C SP708SCN-L/TR 0CTA+70C SP708SCU-L 0CTA+70C SP708SCU-L/TR 0CTA+70C SP708SEN-L -40CTA+85C SP708SEN-L/TR -40CTA+85C SP708TCN-L SP708TCN-L/TR 0CTA+70C 0CTA+70C SP708TEN-L -40CTA+85C SP708TEN-L/TR -40CTA+85C Marking Package SP706SE YYWWL X 8-pin NSOIC 706S EXXX YWW SP706TC YYWWL X 706T CXXX YWW SP706TE YYWWL X 706T EXXX YWW SP708RE YYWWL X SP708SC YYWWL X 708S UXXX YWW SP708SE YYWWL X SP708TC YYWWL X SP706TE YYWWL X Packing Quantity Note 1 Bulk Lead 8-pin NSOIC 2.5K/Tape & Reel Lead Bulk 8-pin MSOP Lead 8-pin MSOP 2.5K/Tape & Reel Lead 8-pin NSOIC Bulk Note 2 Free Free Free Free Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk 8-pin MSOP Lead Free 8-pin MSOP 2.5K/Tape & Reel Lead Free Bulk 8-pin NSOIC Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk 8-pin MSOP Lead Free 8-pin MSOP 2.5K/Tape & Reel Lead Free Bulk Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk 8-pin NSOIC Lead Free 2.5K/Tape & Reel Lead Free 8-pin NSOIC Bulk 8-pin MSOP Lead Free 8-pin NSOIC 8-pin MSOP 2.5K/Tape & Reel Lead Free Bulk Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk 8-pin NSOIC Lead Free 8-pin NSOIC 8-pin NSOIC 2.5K/Tape & Reel Lead Free Bulk Lead Free 8-pin NSOIC 2.5K/Tape & Reel Lead Free 8-pin NSOIC "YY" = Year - "WW" = Work Week - "X" = Lot Number (c) 2010 Exar Corporation 6/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits TYPICAL PERFORMANCE CHARACTERISTICS All data taken at VCC = 2.7V to 5.5V (SP70xR), VCC = 3.15V to 5.5V (SP70xS), VCC = 3.0V to 5.5V (SP70xT), TA= 25C, unless otherwise indicated. Fig. 4: Power-Fail Comparator De-Assertion Response Time Fig. 5: Power-Fail Comparator De-Assertion Response Time Circuit Fig. 6: Power-Fail Comparator Assertion Response Time Fig. 7: Power-Fail Comparator Assertion Response Time Circuit Fig. 8: SP706 RESET Output Voltage vs. Supply Voltage Fig. 9: SP706 RESET Output Voltage vs. Supply Voltage Circuit (c) 2010 Exar Corporation 7/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits Fig. 10: SP706 RESET Response Time Fig. 11: SP706 RESET Response Time Circuit Fig. 12: SP708 RESET and RESET Assertion Fig. 13: SP708 RESET and RESET De-Assertion Fig. 14: SP708 RESET and RESET Assertion and De-Assertion Circuit (c) 2010 Exar Corporation 8/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits Fig. 15: SP708 RESET Output Voltage vs. Supply Voltage Fig. 16: SP708 RESET Response Time Fig. 17: SP708 RESET Output Voltage vs. Supply Voltage and SP813L RESET Response Time Circuit (c) 2010 Exar Corporation 9/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits brownout condition occurs in the middle of a previously initiated reset pulse, the pulse continues for at least another 140ms. On power down, once VCC falls below the reset threshold, RESET stays LOW and is guaranteed to be 0.4V or less until VCC drops below 1V. FEATURES The SP706R/S/T and SP708R/S/T provides four key functions: series 1. A reset output during power-up, powerdown and brownout conditions. 2. An independent watchdog output that goes LOW if the watchdog input has not been toggled within 1.6 seconds. The active-HIGH RESET output is simply the complement of the RESET output and is guaranteed to be valid with VCC down to 1.1V. Some Ps, such as Intel's 80C51, require an active-HIGH reset pulse. 3. A 1.25V threshold detector for power-fail warning, low battery detection, or monitoring a power supply other than +3.3V/+3.0V. WATCHDOG TIMER 4. An active-LOW manual-reset that allows RESET to be triggered by a pushbutton switch. The SP706R/S/T-SP708R/S/T watchdog circuit monitors the P's activity. If the P does not toggle the watchdog input (WDI) within 1.6 seconds and WDI is not tri-stated, WDO goes LOW. As long as RESET is asserted or the WDI input is tri-stated, the watchdog timer will stay cleared and will not count. As soon as RESET is released and WDI is driven HIGH or LOW, the timer will start counting. Pulses as short as 50ns can be detected. The SP706R/S/T devices are the same as the SP708R/S/T devices except for the activeHIGH RESET substitution of the watchdog timer. THEORY OF OPERATION The SP706R/S/T-SP708R/S/T series is a microprocessor (P) supervisory circuit that monitors the power supplied to digital circuits such as microprocessors, microcontrollers, or memory. The series is an ideal solution for portable, battery-powered equipment that requires power supply monitoring. Implementing this series will reduce the number of components and overall complexity. The watchdog functions of this product family will continuously oversee the operational status of a system. The operational features and benefits of the SP706R/S/T-SP708R/S/T series are described in more detail below. Typically, WDO will be connected to the nonmaskable interrupt input (NMI) of a P. When VCC drops below the reset threshold, WDO will go LOW whether or not the watchdog timer had timed out. Normally this would trigger an NMI but RESET goes LOW simultaneously and thus overrides the NMI. If WDI is left unconnected, WDO can be used as a low-line output. Since floating WDI disables the internal timer, WDO goes LOW only when VCC falls below the reset threshold, thus functioning as a low-line output. RESET OUTPUT A microprocessor's reset input starts the P in a known state. The SP706R/S/T-SP708R/S/T series asserts reset during power-up and prevents code execution errors during power down or brownout conditions. On power-up, once VCC reaches 1V, RESET is a guaranteed logic LOW of 0.4V or less. As VCC rises, RESET stays LOW. When VCC rises above the reset threshold, an internal timer releases RESET after 200ms. RESET pulses LOW whenever VCC dips below the reset threshold, such as in a brownout condition. When a (c) 2010 Exar Corporation Fig. 18: Watchdog Timing Waveforms 10/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits MANUAL RESET The manual-reset input (MR) allows RESET to be triggered by a pushbutton switch. The switch is effectively debounced by the 140ms minimum RESET pulse width. MR is TTL/CMOS logic compatible, so it can be driven by an external logic line. MR can be used to force a watchdog timeout to generate a RESET pulse in the SP706R/S/T-SP708R/S/T. Simply connect WDO to MR. Ensuring a Valid Reset Output Down to VCC=0V When VCC falls below 1V, the RESET output no longer sinks current, it becomes an open circuit. High-impedance CMOS logic inputs can drift to undetermined voltages if left undriven. If a pull-down resistor is added to the RESET pin, any stray charge or leakage currents will be shunted to ground, holding RESET LOW. The resistor value is not critical. It should be about 100K, large enough not to load RESET and small enough to pull RESET to ground. Fig. 19: Timing Diagrams with WDI tri-stated. POWER-FAIL COMPARATOR The power-fail comparator can be used for various purposes because its output and non inverting input are not internally connected. The inverting input is internally connected to a 1.25V reference. To build an early-warning circuit for power failure, connect the PFI pin to a voltage divider as shown in Figure 20. Choose the voltage divider ratio so that the voltage at PFI falls below 1.25V just before the +5V regulator drops out. Use PFO to interrupt the P so it can prepare for an orderly power-down. MONITORING VOLTAGES OTHER THAN THE UNREGULATED DC INPUT Monitor voltages other than the unregulated DC by connecting a voltage divider to PFI and adjusting the ratio appropriately. If required, add hysteresis by connecting a resistor (with a value approximately 10 times the sum of the two resistors in the potential divider network) between PFI and PFO. A capacitor between PFI and GND will reduce the power-fail circuit's sensitivity to high-frequency noise on the line being monitored. RESET can be used to monitor voltages other than the +3.3V/+3.0V VCC line. Connect PFO to MR to initiate a RESET pulse when PFI drops below 1.25V. Figure 21 shows the SP706R/S/T-SP708R/S/T series configured to assert RESET when the +3.3V/3.0V supply falls below the RESET threshold, or when the +12V supply falls below approximately 11V. MONITORING A NEGATIVE VOLTAGE SUPPLY The power-fail comparator can also monitor a negative supply rail, shown in Figure 22. When the negative rail is good (a negative voltage of large magnitude), PFO is LOW. By adding the Fig. 20: Typical Operating Circuit (c) 2010 Exar Corporation 11/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits resistors and transistor as shown, a HIGH PFO triggers RESET. As long as PFO remains HIGH, the SP706R/S/T-SP708R/S/T series will keep RESET asserted (where RESET = LOW and RESET = HIGH). Note that this circuit's accuracy depends on the PFI threshold tolerance, the VCC line, and the resistors. INTERFACING TO PS WITH BIDIRECTIONAL RESET PINS Ps with bidirectional RESET pins, such as the Motorola 68HC11 series, can contend with the SP705/706/707/708 RESET output. If, for example, the RESET output is driven HIGH and the P wants to pull it LOW, indeterminate logic levels may result. To correct this, connect a 4.7K resistor between the RESET output and the P reset I/O, as shown if Figure 23. Buffer the RESET output to other system components. Fig. 21: Monitoring +3.3V/+3.0V and +12V Power Supplies Fig. 23: Interfacing to Microprocessors with Bidirectional RESET I/O (SP706) NEGATIVE-GOING VCC TRANSIENT While issuing resets to the P during powerup, power-down, and brownout conditions, these supervisors are relatively immune to short duration negative-going VCC transients (glitches). It is usually undesirable to reset the P when VCC experiences only small glitches. Figure 24 shows maximum transient duration vs. reset-comparator overdrive, for which reset pulses are not generated. The data was generated using negative-going VCC pulses, starting at 3.3V and ending below the reset threshold by the magnitude indicated (reset comparator overdrive). The graph shows the maximum pulse width a negative-going VCC transient may typically have without causing a reset pulse to be issued. As the amplitude of the transient increases (i.e. goes farther below Fig. 22: Monitoring a Negative Voltage Supply (c) 2010 Exar Corporation 12/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits the reset threshold), the maximum allowable pulse width decreases. Typically, a VCC transient that goes 100mV below the reset threshold and lasts for 40s or less will not cause a reset pulse to be issued. A 100nF bypass capacitor mounted close to the VCC pin provides additional transient immunity. Fig. 25: Supply Current vs. Temperature Fig. 24: Maximum Transient Duration without Causing a Reset Pulse vs. Reset Comparator Overdrive APPLICATIONS The SP706P/R/S/T-SP708R/S/T series offers unmatched performance and the lowest power consumption for these industry standard devices. Refer to Figures 25 and 26 for supply current performance characteristics rated against temperature and supply voltages. Fig. 26: Supply Current vs. Supply Voltage (c) 2010 Exar Corporation 13/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits PACKAGE SPECIFICATION 8-PIN NSOIC (c) 2010 Exar Corporation 14/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits 8-PIN MSOP (c) 2010 Exar Corporation 15/16 Rev. 2.0.0 S P 7 0 6 R/ S / T - S P 7 0 8 R/ S / T 3.0V/3.3V Low Power Microprocessor Supervisory Circuits REVISION HISTORY Revision Date 2.0.0 06/04/2010 Description Reformat of datasheet FOR FURTHER ASSISTANCE Email: customersupport@exar.com Exar Technical Documentation: http://www.exar.com/TechDoc/default.aspx? EXAR CORPORATION HEADQUARTERS AND SALES OFFICES 48720 Kato Road Fremont, CA 94538 - USA Tel.: +1 (510) 668-7000 Fax: +1 (510) 668-7030 www.exar.com NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained herein are only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. or its in all Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. (c) 2010 Exar Corporation 16/16 Rev. 2.0.0