WXGA module with LVDS interface
features a fast response time of 5 ms, very wide
viewing cone, brightness of 300 nits,
and 1000:1 contrast ratio.
LQ185T1LGN3 LCD Module
Product Specification
January 2010
LCD Specification
LCD Group
Technical Document
RECORDS OF REVISION
LQ185T1LGN3
SPEC No. DATE REVISED SUMMARY NOTE
No. PAGE
LD-22110 Jan. 29. 2010 1st Issue
LD-22110-1
1. Application
This specification applies to the color 18.5 HD TFT-LCD module, LQ185T1LGN3.
◎This specification are the proprietary product of SHARP CORPORATION(”SHARP) and include materials
protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form
or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written
permission of SHARP.
◎The device listed in this technical literature was designed and manufactured for use in OA equipment.
◎In case of using the device for applications such as control and safety equipment for transportation(aircraft,
trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require
higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and
redundant system design should be taken.
◎Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,
telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment
for life support.
◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply
with the instructions and the precautions specified in these specification sheets.
◎Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.
Graphics and texts can be displayed on a 1366×RGB×768 dots panel with about 16.7 million colors by using
LVDS (Low Voltage Differential Signaling) and supplying +5.0V DC supply voltages for TFT-LCD panel
driving and supply voltage for backlight.
LD-22110-2
3. Mechanical Specifications
Parameter Specifications Unit
Display size 46.7 (Diagonal) cm
18.5 (Diagonal) Inch
Active area 409.8 (H)×230.4 (V) mm
Pixel format 1366 (H)×768 (V) Pixel
(1 pixel＝R+G+B dots)
Pixel pitch 0.3(H)×0.3 (V) mm
Pixel configuration R, G, B vertical stripe
Display mode Normally white
Unit outline dimensions *1 430.37(W)×254.6(H)×9.8(D) (TYP) mm
Mass 1800 (MAX) g
Surface treatment Anti-glare and hard-coating 3H
(Haze value = 25)
*1.Note: excluding back light cables, cover and pet sheets.
The thickness of module (D) doesn’t contain the projection.
Outline dimensions are shown in Fig.7
LD-22110-3
4. Input Terminals
4-1. TFT-LCD panel driving
CN1 (Interface signals and +5.0V DC power supply)
Using connectors ：GS23302-0011R-7F(FOXCONN)
Corresponding connectors ：FI-XB30SRL-HF11(JAE)
(Sharp is not responsible to its product quality, if the user applies a connector not corresponding to the above
model.)
Pin No. Symbol Function Remark
1 NC 【note1】
2 NC 【note1】
3 NC 【note1】
4 GND
5 RxIN0- Receiver signal of LVDS CH0(-) LVDS
6 RxIN0+ Receiver signal of LVDS CH0 (+) LVDS
7 GND
8 RxIN1- Receiver signal of LVDS CH1 (-) LVDS
9 RxIN1+ Receiver signal of LVDS CH1 (+) LVDS
10 GND
11 RxIN2- Receiver signal of LVDS CH2 (-) LVDS
12 RxIN2+ Receiver signal of LVDS CH2 (+) LVDS
13 GND
14 CK IN- Receiver signal of LVDS CLK (-) LVDS
15 CK IN+ Receiver signal of LVDS CLK (+) LVDS
16 GND
17 RxIN3- Receiver signal of LVDS CH3(-) LVDS
18 RxIN3+ Receiver signal of LVDS CH3(+) LVDS
19 GND
20 NC 【note1】
21 NC 【note1】
22 NC 【note1】
23 GND
24 GND
25 GND
26 Vcc +5.0V Power supply
27 Vcc +5.0V Power supply
28 Vcc +5.0V Power supply
29 Vcc +5.0V Power supply
30 Vcc +5.0V Power supply
[Note 1] Not connection, this pin should be open.
LD-22110-4
4-2 LVDS Data Mapping
CX IN+
CX IN-
RxIN0+
RxIN0-
RxIN1+
RxIN2+
RxIN2-
RxIN1-
RxIN3-
RxIN3+
DE : Display Enable
NA : Not Available
G0 R5 R4 R3 R2 R1 R0 R0 R1 G0
B1 B0 G5 G4 G3 G2 G1 G1 G2 B1
DE B5 B4 B3 B2 B2 B3 DE NA NA
1 c
y
cle
NA G7 G6 R7 R6 R6 R7 NA B7 B6
LD-22110-5
4-3 Backlight
CN2, 3 (Upper/Lower FPC Connector Pin Assignment)
Using connector ：7080-Q10N-00R (Entery INDUSTRIAL CO.,LTD)
Corresponding FFC specification ：Temperature＝80oC, Voltage=60V, Pin No.=10, 0.5Pitch, PET, HF
CN2 and CN3 are the same pin assignment.
Pin No Symbol Description
1 IRLED1 IRLED1 LED current sense for string 1
2 IRLED1 IRLED1 LED current sense for string 1
3 IRLED2 IRLED1 LED current sense for string 2
4 VLED LED power supply
5 VLED LED power supply
6 VLED LED power supply
7 VLED LED power supply
8 IRLED2 IRLED1 LED current sense for string 2
9 IRLED3 IRLED1 LED current sense for string 3
10 IRLED3 IRLED1 LED current sense for string 3
5. Absolute Maximum Ratings
Parameter Symbol Condition Ratings Unit Remark
Supply voltage Vcc Ta=25℃ －0.3 ～ + 6.0 Ｖ
Input voltage VI Ta=25℃ －0.3 ～ + 4.3 V
Storage temperature TSTG － －20 ～ + 60 ℃ 【Note1】
Operating temperature (Ambient) TOPA － 0 ～ + 50 ℃ 【Note2】
【Note1】The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or less.
At temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.
【Note2】The unit should not be exposed to corrosive chemicals.
CN2
CN3
LD-22110-6
6. Electrical Characteristics
6-1. TFT-LCD panel driving Ta＝25℃
Parameter Symbol Min. Typ. Max. Unit Remark
Supply voltage Vcc +4.5 +5.0 +5.5 V 【Note2】
Current dissipation Black Icc － 700 1000 mA 【Note3】
White Icc
－ 500 700 mA 【Note4】
Mosaic Icc – 700 1000 mA 【Note5】
Permissive input ripple voltage VRF － － 150 mVp-p
Differential input High VTH － － +100 mV VCM=+1.2V
threshold voltage Low VTL –100 － － mV 【Note1】
Terminal resistor RT － 100 － Ω Differential input
【Note1】 V
CM : Common mode voltage of LVDS driver.
【Note2】
1）On-off conditions for supply voltage
Symbol Min. Max. Unit Remark
t1 0.1 10 ms
t2 0 50 ms
t3 0 50 ms
t4 0.1 50ms ms
t5 1000 － ms
t6 200 － ms *1
t7 100 － ms *1
*1 : Power sequence for Backlight is not especially specified, however it is recommended to consider some
timing difference between LVDS input and Backlight input as shown above.
If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the screen
may look white for a moment or abnormal image may be displayed.
This is caused by variation in output signal from timing generator at LVDS input on or off.
It does not cause the damage to the LCD module.
t1 t2
t6
0.9Vcc0.9Vcc
Vcc
Valid
Backlight
Signal
(LVDS Interface)
0.1Vcc 0.1Vcc 0.1Vcc
t3 t5
OFF
OFF
Backlight ON
(LED)
t7
t4
90% 90%
LD-22110-7
【Note3】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition
whereas black pattern is displayed.
【Note4】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition
whereas white pattern is displayed.
【Note5】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition
whereas mosaic pattern(black & white [8*6] ) is displayed.
White : GS255
Black : GS0
6-2. Backlight Driving
The backlight system is edge-lighting type with 156 White-LED(White Light Emitting Diode,
(13 serial x 2 parallel) x 3 strings x 2 (Upper/Lower) ).
The characteristics of White-LED are shown in the following table.
(Ta = 25℃)
Parameter Symbol Min. Typ. Max. Unit Remark
Supply voltage range VLED － 42.9 44.2 V Duty 100%
Current dissipation ILED － － 240 mA
【Note1,2,3】
Power Consumption PLED － － 10.6 W
【Note4】
LED Life time LBL 25,000 30,000 － Hour 【Note5】
【Note1】There are two Light Bars, and the specified current is input LED chip 100% duty current.
【Note2】The sensing current of each string is 40mA.
【Note3】Each light bar have three current sensing strings, so that each light bar input current is 120mA.
【Note4】PLED = ILED × VLED , LED matrix is (13S2P)x 3 strings x 2.
【Note5】The life time is determined as the time at which luminance of the LED becomes 50% of the
initial brightness or not normal lighting at ILED=240mA on condition of continuous operating
at 25±2°C.
【Note6】In case of using PWM control for blacklight driving, please keep frequency enough high in order to
avoid the flicker or the deterioration of display quality.
LD-22110-8
7. Timing characteristics of input signals
7-1. Timing characteristics
Parameter Symbol Min. Typ. Max. Unit
Clock signal Frequency 1/Tc 62.9 75.4 95.6 MHz
Horizontal period TH 1400 1560 1800 Clock Horizontal
Horizontal period(High) THd 1366 1366 1366 Clock
Vertical period TV 786 806 900 Line
Vertical period(High) TVd 768 768 768 Line
Vertical
frequency fv 50 60 76 Hz
【Note】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.
1 2 1366
THd
TH
TVd
TV
Tc
1 2 768
767
1366
DE
DATA
(R,G,B)
DE
LD-22110-9
7-2 Input Data Signals and Display Position on the screen
１・１ １・２ １・３
２・１ ２・２
３・１
768･1
1･1366
768･1366
R1 G1 B1 R2 G2 B2
(１､１) (１,２)
Display Position of Data (V,H)
R G B
LD-22110-10
8. Input Signals, Basic Display Colors and Gray Scale of Each Color
8-1 8bit input
Data signal
Colors & Gray
Gray scale Scale
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7
Black － 0 0 0 0 0 0 0000000000 0 0 0 00000
Blue － 0 0 0 0 0 0 0000000000 1 1 1 11111
Green － 0 0 0 0 0 0 0011111111 0 0 0 00000
Cyan － 0 0 0 0 0 0 0011111111 1 1 1 11111
Red － 1 1 1 1 1 1 1100000000 0 0 0 00000
Magenta － 1 1 1 1 1 1 1100000000 1 1 1 11111
Yellow － 1 1 1 1 1 1 1111111111 0 0 0 00000
White － 1 1 1 1 1 1 1111111111 1 1 1 11111
Black GS0
0 0 0 0 0 0 0000000000 0 0 0 00000
× GS1
1 0 0 0 0 0 0000000000 0 0 0 00000
Darker GS2 0 1 0 0 0 0 0000000000 0 0 0 00000
× È È È È
Ø È È È È
Brighter GS253 1 0 1 1 1 1 1100000000 0 0 0 00000
Ø GS254
0 1 1 1 1 1 1100000000 0 0 0 00000
Red GS255
1 1 1 1 1 1 1100000000 0 0 0 00000
Black GS0
0 0 0 0 0 0 0000000000 0 0 0 00000
× GS1
0 0 0 0 0 0 0010000000 0 0 0 00000
Darker GS2 0 0 0 0 0 0 0001000000 0 0 0 00000
× È È È È
Ø È È È È
Brighter GS253 0 0 0 0 0 0 0010111111 0 0 0 00000
Ø GS254
0 0 0 0 0 0 0001111111 0 0 0 00000
Green GS255
0 0 0 0 0 0 0011111111 0 0 0 00000
Black GS0
0 0 0 0 0 0 0000000000 0 0 0 00000
× GS1
0 0 0 0 0 0 0000000000 1 0 0 00000
Darker GS2 0 0 0 0 0 0 0000000000 0 1 0 00000
× È È È È
Ø È È È È
Brighter GS253 0 0 0 0 0 0 0000000000 1 0 1 11111
Ø GS254
0 0 0 0 0 0 0000000000 0 1 1 11111
Blue GS255
0 0 0 0 0 0 0000000000 1 1 1 11111
0 : Low level voltage, 1 : High level voltage.
Each basic color can be displayed in 255 gray scales from 8 bit data signals. According to the combination of
total 24 bit data signals, the 16.7-million-color display can be achieved on the screen.
Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue
LD-22110-11
9. Optical Characteristics
Parameter Symbol Condition Min. Typ. Max. Unit Remark
θ11 70 80 － Deg.
Vertical
θ12 70 80 － Deg.
Viewing
angle
range Horizontal θ21,θ22
CR≧10
75 85 － Deg.
【Note3,5,6】
Contrast ratio ＣＲ θ=0°700 1000 － 【Note3,7】
Response Rise τr － 1.5 4 ms
【Note4】
Time Fall τd － 3.5 6 ms
Rise+Fall τr +τd － 5 10 ms
x 0.283 0.313 0.343 【Note3】
Chromaticity of
White y 0.299 0.329 0.359
x 0.609 0.639 0.669
Chromaticity of
Red y 0.316 0.346 0.376
x 0.293 0.323 0.353
Chromaticity of
Green y 0.598 0.628 0.658
x 0.122 0.152 0.182
Chromaticity of
Blue y 0.031 0.061 0.091
Luminance of white Y
L
250 300 － cd/m2 【Note3】
White Uniformity δw1
θ=0°
0.70 0.75 － － 【Note3,8】
Cross Talk Dsha θ=0°－ － 2 % 【Note9】
【Note1】Ambient temperature = 25°C.
【Note2】To be measured in dark room after backlight warm up 30 minutes.
【Note3】To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.
【Note4】 Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time
interval is between the 10% and 90% of amplitudes. Refer to figure as below.
τ
r
τ
d
0%
10%
90%
100%
White white
b
lac
k
time
Photodetector Output
(Relative Value)
LD-22110-12
【Note5】Optical Characteristics Measurements:
【Note6】Definitions of viewing angle range:
【Note7】Definition of contrast ratio:
The contrast ratio is defined as the following.
Contrast Ratio(CR) = Luminance(brightness)with all pixels white
Luminance(brightness)with all pixels black
【Note8】Definition of white uniformity:
White uniformity is defined as the following with nine measurements (1～9).
σw1 = Minimum Brightness of nine points(P1～P9).
Maximum Brightness of nine points(P1～P9).
W/10
W/2
9W/10
W
D/10 D/2 9D/10
D
2 1 3
5 4 6
8 7 9
Normal line
θ21
θ11
θ12
θ22
6 o’clock direction
Center of screen
(
θ=0°
)
TFT-LCD-Module
500mm
Field=2°
BM-5A
(TOPCON)
LD-22110-13
【Note9】Definition of cross talk:
We measured luminance in case there are a window frame and in case there are not a window frame with A points
& B points of the following figure. Then, we compared the measured values.
Dsha(%) = |Luminance with a window frame - Luminance without a window|
Luminance without a window ×100
0 gray level
1/2
1/2
1/6
1/6
A
B
1/2 1/6
1/6
2/3 1/3
A’
B’
127 gray level 127 gray level
1/
3
1/
2
2
/
3
LD-22110-14
10. Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
warp or twist.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
Blow away dust on the polarizer with antistatic N2 blow. It is undesirable to wipe off because a polarizer is
sensitive. It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to
the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Handle with care.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
when handling.Observe all other precautionary requirements in handling components.
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
i) Protection film is attached to the module surface to prevent it from being scratched .
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
protective board over the LCD, be careful about the optical interface fringe etc. which degrades display
quality.
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
panel is used under such environment.
l) Connect GND to 8 place of mounting holes to stabilize against EMI and external noise.
m) When handling LCD modules and assembling them into cabinets, please avoid that long-term storage in
the environment of oxidization or deoxidization gas and the use of such materials as reagent,solvent,
adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules.
o) When install LCD modules in the cabinet, please tighten with “torque=2.0kgf･cm(Max)”.
Be sure to confirm it in the same condition as it is installed in your instrument.
p) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if itgets
inside your eye or mouth by mistake.
q) Notice : Never dismantle the module , because it will cause failure. Please don't remove the fixed tape,
insulateing tape etc that was pasted on the original module. (except for protection film of the panel and
the crepe tape(yellow tape) of fixing lamp cable temporarily.)
r) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
(Please use a screen saver etc., in order to avoid an afterimage.)
s) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
t) If a minute particle enters in the module and adheres to an optical material, it may cause display
non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole
if you intend to install a fan.
LD-22110-15
11. Packing form
a) Piling number of cartons : maximum 2 cartons
b) Packing quantity in one carton : 10 modules
c) Carton size : 500mm(W)×285mm(D)×435mm(H)
d) Total mass of one carton filled with full modules : 17.5kg(Max.)
e) Packing form is shown in Fig.1,2,3
Fig 1 Fig 2 Fig 3
Step 1 Take a carton and put inner pad as fig1.
Step 2 Place the module with PCBA under then put it falls horizontally into the carton all 10pcs as fig2.
Step 3 Cover them with 2pcs top pad then to seal discount as fig3.
Inner Pad
Top Pad
LD-22110-16
12. Shipping Pallet Package
a) Total mass of two pallets filled with full modules : 605kg(Max.)
Step 1 Place a pallet specially, spec is:1130mm*1100mm*140mm,as fig4.
Step 2 Stack cartons on the Pallet in 2 tiers,8 cartons in a tier, total 16 cartons.
Then place Corner paper and Upper Cover, as fig5.
Step 3 Pile of cargo according to 2 tiers pallets.
Notes: top pallet and bottom pallet need to pile up neat and tidy as fig6.
棧板
Fig 4 Fig 5 Fig 6
Corner paper×4
Cover×1
Pallet×1
Pallet
Carton×16
LD-22110-17
13．Reliability test items
No Test item Conditions Judgment Remark
1 High temperature storage test 60℃, 240h Note 1 Note 2
2 Low temperature storage test -20℃, 240h Note 1 Note 2
3 High temperature
& high humidity operation test
40℃, 90%RH, 240h
(No condensation)
Note 1 Note 2
4 High temperature operation test 50℃, 240h Note 1 Note 2
5 Low temperature operation test 0℃, 240h Note 1 Note 2
6 Vibration test
(non- operating)
Vibration level : 1.5G
Bandwidth : 10-300Hz
Waveform : sine wave,
Sweep rate : 10min
30 min for each direction X, Y, Z
(1.5 Hrs in total)
Note 1 Note 2
7 Shock test
(non- operating)
Shock level : 50G, 11ms
Waveform : Half sine wave
Direction : ±X, ±Y, ±Z
One time each direction
Note 1 Note 2
8 Thermal shock test
(Storage)
-20℃～60℃
1Hr, 1Hr, 100cycles
Note 1 Note 2
9 ESD test
Contack : +/-8kV, 150pF(330ohm)
10times/1point, time/1 sec
Air discharge : +/-15kV, 150pF(330phm)
9points,10times/1point, 1time/1 sec
Note 1 Note 2
10 MTBF Demonstration 30,000 hours with confidence level 90% Note 1 Note 3
【Note 1】Pass: Normal display image with no obvious non-uniformity and no line defect.
Partial transformation of the module parts should be ignored.
Fail: No display image, obvious non-uniformity, or line defects.
【Note 2】Evaluation should be tested after storage at room temperature for one hour.
【Note 3】The MTBF calculation is based on the assumption that the failure rate distribution meets the
Exponential Model, and B/L is not included.
LD-22110-18
14．Others
1) Lot No. and indication Bar Code Label:
Serial No.
Z
1 Z
2 Z
3 Z
4 Z
5 Z
6 Z
7 Z
8 Z
9 Z
10
Serial ID includes the information as below:
1. Year: Final digit of the A.D. EX.”0” for 2010
2. Month: 1~9, X, Y, and Z. (X=Oct. Y=Nov. Z=Dec.)
3. Day: 1～9,A to X.(please refer Day Code table)
4. Sharp internal use
5. Serial No: 0~99999, Over 10Kpcs use A, B, C…
For example: Actual Print
99,999 99999
100,000~ A0000~
110,000~ B0000~
120,000~ C0000~
6. Revision code: The first Version is A, version changes with design change.
Version with 26 letters, For example: A, B, C…
Day Code table
Date Day Code Date Day Code Date Day Code
1111B21M
2212C22N
3313D23P
4414E24Q
5515F25R
6616G26S
7717H27T
8818J28U
9919K29V
10 A 20 L 30 W
31 X
2
0
m
m
45 mm
SHARP
LQ185T1LGN3
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10
Revision code
Month
Year
Sharp Internal use
Serial No
Day
LD-22110-19
2) Packing Label
① Model No. (LQ185T1LGN3)
② Lot No. (Date)
③ Quantity
3) If any problem occurs in relation to the description of this specification , it shall be resolved through
discussion with spirit of cooperation.
社内品番：（４Ｓ）LQ185T1LGN3
ＬｏｔＮＯ． ：（１Ｔ）２０１０．Ｘ．ＸＸ
Ｑｕａｎｔｉｔｙ：（Ｑ） １０ ｐｃｓ
ユーザ品番 ：
Bar code（①）
Bar code（②）
Bar code（③）
シャープ物流用ラベルです。
LD-22110-20
Fig7.LQ185T1LGN3 OUTLINE DIMENSIONS
NORTH AMERICA
Sharp Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-8700
Fax: (1) 360-834-8903
www.sharpsma.com
TAIWAN
Sharp Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
CHINA
Sharp Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: smc@china.global.sharp.co.jp
EUROPE
Sharp Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: 49 (0)180 507 35 07
Fax: (49) 40-2376-2232
www.sharpsme.com
SINGAPORE
Sharp Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
KOREA
Sharp Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
JAPAN
Sharp Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
HONG KONG
Sharp-Roxy (Hong Kong) Ltd.
Level 26, Tower 1, Kowloon Commerce Centre,
No. 51, Kwai Cheong Road, Kwai Chung,
New Territories, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 602-603, 6/F.,
International Chamber of Commerce Tower,
168 Fuhua Rd. 3, CBD,
Futian District, Shenzhen 518048,
Guangdong, P.R. China
Phone: (86) 755-88313505
Fax: (86) 755-88313515
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for
limitations on special applications. See Limited Warranty for SHARP’s product warranty.
The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,
ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in
any way, for any incidental or consequential economic or property damage.
LCD Group
LCD Specification
Technical Document
