SF2026B (R) * * * Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Complies with Directive 2002/95/EC (RoHS) 114.815 MHz Pb SAW Filter Absolute Maximum Ratings Rating Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Value Units +10 dBm 0 VDC -60 to +95 Suitable for lead-free soldering - Max Soldering Temperature C 260C for 30 s SMP-03 Electrical Characteristics Characteristic Center Frequency of IF SAW Filter (RF LO 50ppm correction to 1st IF) Insertion Loss Amplitude Ripple (p-p) between 111.7594.......113.4107 MHz (BW=1.64 MHz 50ppm) Amplitude Ripple (p-p) between 113.5993.......115.2508 MHz (BW=1.64 MHz 50ppm) Amplitude Ripple (p-p) between 115.3492.......117.8709 MHz (BW=1.64 MHz 50ppm) Pass Bandwidth of -1.5 dB Pass Bandwidth of -3 dB Low side attenuation 80 MHz...102.815 MHz (Fc -12 MHz) Low side attenuation 102.815 MHz...107.690 MHz (Fc -7.125 MHz) Low side attenuation 107.690 MHz...109.690 MHz (Fc -5.125 MHz) High side attenuation 121.260 (Fc +6.445 MHz)...123.860 MHz (Fc +9.045 MHz) High side attenuation 123.860 MHz...126.815 MHz (Fc +12.00 MHz) High side attenuation 126.815 MHz...150.815 MHz (Fc +36.00 MHz) Sym fC IL Notes Min 1 Typ 114.815 12.5 Notes: 1. 2. 3. 4. 5. 6. 7. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard Per ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 1.3 38 36 28 25 36 38 1 6 10. 11. 6.30 7.24 40 38 30 27 38 40 MHz dB 80 ns 80 ns 100 ns -40 +85 C SMP-03 7 x 5 mm Nominal Footprint RFM SF2026B YYWWS US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. (c)Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. J = 50 Ohms J = 50 Ohms RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. dB 1.3 TA 8. 9. 15 Units MHz dB 1.3 Group Delay Ripple (p-p) between 111.7594.......113.4107 MHz (BW=1.64 MHz 50 ppm) Group Delay Ripple (p-p) between 113.5993.......115.2508 MHz (BW=1.64 MHz 50 ppm) Group Delay Ripple (p-p) between 115.3492.......117.8709 MHz (BW=2.510 MHz 50 ppm) Operating Temperature Range Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Max E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 1 of 6 114.815 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 2 of 6 114.815 MHz CH1 S 11 SAW Filter 1 U FS 1_: 40.76 28 Aug 2003 09:06:31 0.5801 804.09 pH 114.815 000 MHz PRm Cor 1 CH2 S 22 1 U FS 1_ 61.52 15.119 20.958 nH 114.815 000 MHz PRm Cor CENTER 114.815 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 1 SPAN 100.000 000 MHz E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 3 of 6 114.815 MHz SAW Filter SF2026B Recommended Matching Component for 200 ohm load on Input and Ouput upon Differential SAW Inductor Part Number 0603CSR10XJBW Value 100nH Size 0603 Tolerance Recommended Manufacturer 5% Coilcraft 0603CS-series Capacitor Part Number 0603CG220J9B20 0603CG180J9B20 Value 22 pF 18 pF Size 0603 0603 Tolerance 5% 5% Philips Philips Recommended Manufacturer 20.0 mm 47.3 mm RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 4 of 6 114.815 MHz SAW Filter SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions Dimension A B C D E H J K P Recommended PCB Footprint Min 6.80 4.80 .47 2.41 0.87 4.87 2.87 1.14 mm Nom 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 Max 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 Min 0.268 0.189 0.019 0.095 0.034 0.192 0.113 0.045 Inches Nom 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 Max 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 Materials Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body Al2O3 Ceramic Pb Free Electrical Connections Connection Port 1 Port 2 Terminals Input or Return 10 Return or Input 1 Output or Return 5 Return or Output 6 Ground All others Single Ended Operation Return is ground Differential Operation Return is hot C B E H H A J D P K RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 5 of 6 114.815 MHz SAW Filter Tape and Reel Specifications 100 REF. "B" REF. "B " Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 12.0 16.0 .2 20 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2026B-060305 Page 6 of 6