REVISIONS LTR DESCRIPTION DATE (YA-M0-0A) APPROVED REV SHEET REV SHEET REV STATUS REV OF SHEETS sHeeT fi] 24/3 fads 6] 7/8 fo fiofrifiz [13 (v4 p15 f 16417 PMIC WA PREPARED BY i 4ehe DEFENSE ELECTRONICS SUPPLY CENTER PF, DAYTON, OHIO 45444 STANDARDIZED bo Y : MICROCIRCUITS, MIL-S1D-1553, DATA TERMINAL MILITAR PROVED BY BIT PROCESSOR, HYBRID DRAWING j : ip. ) x THIS DRAWING IS AVAILABLE = FOR USE BY ALL DEPARTMENTS ORAWING APPROVAL DATE SE CAGE CODE AND AGENCIES OF THE 91-01-28 A 67268 5962-90636 DEPARTMENT OF DEFENSE SEVSION DEVEL AMSC NIA SHEET 1 OF 17 dese i 193 US, GOVERNMENT PRINTING OFFICE: 1987 748-12600911 5962-E011 DISTRIBUTION STATEMENT A. Approved for public release; distribution is untimited.1. SCOPE 1.1 Scope. This drawing forms a part of a one part - one part number documentation system (see 6.6). This drawing describes device requirements for hybrid microcircuits to be processed in accordance with MIL-H-38534. Two product assurance classes, military high reliability (device class H) and space application (device class K} and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shal] be as shown in the following example: 5962 - 90636 ol H X X | | | qT ToF ' | \ | i | i | Federal RHA Device Device Case Lead stock class designator type class outline finish designator (1.2.1) (1.2.2) designator (1.2.4) (1.2.5) \ / (1.2.3) V Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall] meet the MIL-N-28534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non RHA device. 1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function ol CT1820 MIL-STD-1553 data terminal bit processor 02 CT1820-2 MIL-STD-1553 data terminal bit processor with high data bus driver capability 03 ARX2410 MIL-STD-1553 data terminal bit processor 04 ARX3410 MIL-STD-1553 data terminal bit processor 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level (see 6.7 herein) as follows: Device class Device requirements documentation H and K Certification and qualification to MIL-H-38534 1.2.4 Case outline(s). The case outline(s) shall be as designated in appendix C of MIL-M-38510, and as follows: Outline letter Case outline X See figure 1, (56-pin, 2.155" x 1.155" x .200"), plug-in package Y See figure 1, (60-pin, 1.590" x 1.015" x .125"), flat package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-H-38534 for classes H and K. Finish letter x shall not be marked on the microcircuit or its packaging. The "X" designation is for use in specifications when lead finishes A, B, and C are considered acceptable and interchangeable without preference. STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 > DESC FORM 193A SEP 87 * US GOVEANMENT PRINTING OFFICE 1990-750 527A1.3 Absolute maximum ratings. 1/ ly voltage (Vcr )- - --- <= cc ee rte +7.0 V de Supply wor tage tye ee -0.3 dc to +5.5 V de CLOCK IN input voltage- - - -----> 7-77 -0,3 de to Yee + 0.3 V dc Storage temperature range - -------- 7 -65 c to +150 Lead temperature (soldering, 10 seconds)- -- - +300 C Power dissipation (Pp): Device types Ol, 08, and 04 --+--+----+-- 347 mW Device type 02- ----+----- +7777 7 1392 mi Thermal resistance, junction-to-case (@jc): . Device type 01, cases X and Y------- - 5.68 /W Device type 02, cases X and Y-------- 46.64 c/w Device types 03 and 04, case X- -+------ 5.68 C/wW 1.4 Recommenced operating conditions. Supply voltage (Vcec)- - ---- set ett +4.5 V de to +5.5 V de Case operating temperature range (Tc) - - - - - -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specifications, standards, and handbook. Unless otherwise specified, the following specifications, standards, and handbook of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIF ICATIONS MILITARY MIL-M- 38510 - Microcircuits, General Specification for. MIL-H-38534 - Hybrid Microcircuits, General Specification for. STANDARDS MILITARY MIL-STD-480 - Configuration Control-Engineering Changes, Deviations and Waivers, MIL ~STD-&83 - Test Methods and Procedures for Microelectronics. HANDBOOK MILITARY MIL-HUBK-780 - Military Drawings. (Copies of the specifications, standards, and handbook required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 3 DESC FORM 193A SEP 87 @ US. GOVERNMENT PRINTING OFFICE 1990 7S)-52/7,2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 Item requirements, The individual item requirements shall be in accordance with MIL-H-38534 and as specified herein, 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-H-J38534 and herein, 3.2.1 Case outline(s}. The case outline(s) shall be in accordance with 1.2.4 herein and figure 14 3.2.2 Terminal ccanections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specitied in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shal] be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-H-38534. The part shall be marked with the PIN ti sted in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in QM -38534. 3.6 Manufacturer eligibility. In addition to the general requirements of MIL-H-38534 the manufacturer of the part described herein shall submit for DESC-ECC review and approval electrical test data (variables format) on 22 devices from the initial quality conformance inspection group A lot sample, produced on the certified line, for each device type listed herein. The data should also include a summary of all parameters manually tested, and for those which, if any, are guaranteed. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance submitted to DESC-ECC shall affirm that the manufacturer's product meets the requirements of MIL-H-38534 and the requirements herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-H-38534 shalt be arovided with each lot of microcircuits delivered to this drawing. 4, QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-H-38534, STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 4 DESC FORM 193A SEP 87 * US GOVERNMENT PRINTING OFFICE 1990. 750-5777TABLE I. Electrica) performance characteristics. I I T T T } T Test {Symbol | Conditions {Group AlDevicel Limits [Unit { | 44.5 Vic Veo < +5,5 V |sub- {types | | | | ~55C <Te < F125 C groups | | | | ! unless otherwise specified | ! Min Max cm Taalgelea Input high voltage lV 1,2, 02,1 . 9 pH | | jon TT | | | | | | I | [Only for Dg-Dy5, Ag-Ag 1,2,3 103 3.5 | v | | I J in I ] | Input low voltage Von | | 1,2,3 av} | 0.71 Vv } t t 1 | i i | | 1 ] i | | Input high current ily YIN = 2.5 [Clock IN input | 1,2,3 JAI] | 1100 | uA | ] | I D ] I | | |All other inputs {| 1,2,3 {All| | 20 | uA | T q i | 1 | I Input Yow current {tn {VIN = 0.4 V {Clock IN input | 1,2,3 {aN} | 0.1 mA | | ] T T T T T | | |A1] other inputs | 1,2,3 |All | } -0.4} mA l l { | I | | | T 1 l ] ] ] I Output high voltage IVq, [Outputs Do - Dys, ESC OUT, 11,2,3 [All | | 2.51 V i {DSC OUT, and CLOCK OUT, | | | \ | | I Toy = -1000 yA | | | | | { | ! | | | | | i ] | T I I ! | Output MODE CODE, Iqy = -600 pA 1,2,3 jan | | 2 | vy | | T T T T I i | |All other outputs, }1,2,3 JAI] | j 2.51 | oy = -400 yA | 1 l | | | | | | | I { | | y | | I | r Output low voltage 1o. - [Outputs [Iq = 6.0 ma 1 1,2,3 {ol | { 0.4] i [Dg - Dus | i i { | i | | | | | I 1 1 | {Top = 10 mA | 1,2,3 {02,04 | | 0.41 V i \ | | | | | i | | I 1 T t I I | | lig, = 3.6 mA } 1,2,3 [03 =| | 0.4] Vv | | | ! | i | | | | | I I | T | Output MOOE CODE, Iq. = 6.0 mA | 1,2,3 jan | 0.41 V | if t | | I T | {Outputs ESC OUT and DSC OUT, } 1,2,3 |All | { 0.4) V | liq. = 1.2 mA | | | | | | | | | | | | \ | I | | | | | Output clock out, Iq = 1.0 m 1,2,3 jan | | 0.4| v See footnotes at end of table. STANDARDIZED ry 5962-90636 MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 5 DESC FORM 193A SEP 87 # US, GOVERNMENT PRINTING OFFICE: 1990-750.527RTABLE I. Electrical performance characteristics - Continued. | ] | Test {Symbol | Conditions \ croup A\Device| Limits Unit | | 4.5 V < Woo < *5,5 V |sub- | types | | | | 55C Te < Fl25 C {groups | j | ! unless otherwise specified ! Min Max | T f ] | | | Output low voltage Vor {All other outputs, }1,2,3 [All | } 0.4] | Io, = 4.0 mA l | | I { { \ | i \ | { 1 T T T T T ] Clock inout high rue | }1,2,3 [AIT !Vee -l | io} taye i \ | I i 9.5! i | { | I I | { 1 l | | | I | Clock input low Wire | }1,2,3 [All | |GND +] V voltage | | | i i { 0.51 | | | | i { | | i | | | i i Clock output high Woe | 1 1,2,3 [Al] I ec -1 lv vol tage | | | | 1 9.3! | | { | | I | { I | qT I I T | Clock output low Yor! 11,2,3 [All | JGND +1 V vol tage | I | | i { 0.3] | | I | | | { | | | | I | I Logic supply current { "cc | 1,2,3 [92-03 | { 50 | mA 04 | i | | | | I I T | | I | 102 | }240 | T T T | T T | Oscillator/clock Ilosc | | 1,2,3 }01,02,| 1 13 | mA supply current ! ! I 104 | | ! | | | | | {03s 30 | J ] | | | ] { Functional test \FT }See 4.3.1c 17,8A,88/A11 =| | | | | | | | | Encoder timing J T . | T I | ENC ENA setup time tel {See figure 4 {9.10,11 AN] {100 ! ns J | ] T ] | ENC ENA hold time |te2 ! 19,10,11/01,02 | 80 | ns It l T T | ! 19,10,11103,04 |100 | l_ns { | 1 } \ SYNC SELECT setup Ite; | 19,10,11/A1} {125 | | as time | I | | | | | . | | | | | | \ SYNC SELECT hold time | tee 19,10, 111411 {180 | ! ns | | | | | | See footnotes at end of table. STANDARDIZED SIZE 5962- MILITARY DRAWING A 62-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 6 DESC FORM 193A SEP 87 * US GOVERNMENT PRINTING OFFICE 1990 750-5277TABLE I, Electrical performance characteristics - Continued. unless otherwise specified | i | | I i Test {Symbol | Conditions JGroup AlDevicel Limits [Unit | | *4.5 V < Woo < +5,5 V }sub- [types | | | -55C <Te < F125 C [groups | | | | herwi & | | Min | Max | | | Encoder timing - Continued | | i | SEND DATA delay time [tes {See figure 4 9,10, 11/AlT =| | 75 ns | | | | | { i | | | | | LATCH DATA hold time | tes | {9520.12 1A01 ! 10 | | ns | | ' ' i i t { | I LATCH DATA setup time | te7 | 19,10, 12 All | 50 ! ! ns | | | [ | [T Parallel data setup lteg, | 19,10, 11101 125 | [ ns time tei ! | j | | | 1 If | 02,03.) 40 | | | | | |04 | | | | | T I T J | Parallel data hold time |tgg, | 19,10,111A11 | 60 | ] ns iter3| | l | | | ly | | { | | | I~ J { | | | | | | | | | | | DATA SELECT disable Itei0 | 19,10, 11/A1]1 | 30 | | ns time | | | { | | | | | | T I DATA SELECT hold time tell 9,10,11/41] ! 0 | ns Decoder timing y T ] T T T | TAKE DATA delay on time | tp) {See figure 4 19.10, 12/A1} 1325 ns | | | l T T ] I TAKE DATA delay off itp2 | J9,10,1R1AlT = | 1125 | ons time | | l | | { | | | | | I | | } j T T ] I J Sync delay time | tos | 19,10,11101,02 | { 60 | ons t D I q l | { 19,10,11103,04 | J110 | ons | 1 | | 1 T | VALID WORD delay time | toa ! 19,20,121A11 | 1125 ns l I | | | | | | | 1 | | | BROADCAST delay time | tus | }9.10,111A11 | | 70 ns See footnotes at end of table. STANDARDIZED A 5962-90636 MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET OAYTON, OHIO 45444 7 DESC FORM 193A SEP 87 # US GOVERNMENT PRINTING UFFICE 1990 7505778TABLE I. Electrical performance characteristics - Continued. | | | q I I Test }Symbol | Conditions \Group AlDevicel Limits [Unit { i +4.5 Vi < Wc < *5,5 V {sub- [types | | { | 55C <T < F126 C |groups | T T | I { herwis. | Min | Max | | I unless otherwise specified | | | Decoder timing - Continued { ] | | | KT ENABLE delay time | tog |se figure 4 19,10,12 (AI) | 1100 ns { I | } | { | { i MODE COUE delay time {to7 19,10, 111A11 ! ies ! ns ] | | | | | | DATA SELECT input delay |tpg =| 19,10,11/A17 | 0 | | ns time 2/ |. | { | { | | | { | { | | | T | TO l T T T Parallel data output | tpg | 19,10,11]01,04 | {| 60 | ns delay time | | | | | ! | | | 102,03 | 175 | { | { | { | I 1/ tez2 and te,3 apply only when LATCH DATA is not used. 2/ DATA SELECT may be applied at any time that the 16 line 1/0 is otherwise free. The parallel data out, however, is not new data until tog after TAKE DATA goes high. STANDARDIZED A 5062-90636 MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 8 DESC FORM 193A + US GOVERNMENT PRINTING OFFICE. 1990-750-527R SEP 87Case outline X 2.155 MAX ______wm] 1.900 (ag 29 OOODODOOOGOO0DOOODODOO as 28 1 | -450 REF 1,155 i MAX e gS 3900 56 210 i Qee OOODDODODDOOOOODOODO 20) 100 TYP CONTRASTING COLOR BEAD { DENOTES PIN | *200 MAX J_I L TUT Q.018 +.002 > (56 PLACES) Inches mm .002 .05 .018 46 . 100 2.54 - 200 5.08 -450 11.43 - 900 22.86 1.155 29.34 1.900 48.26 2.155 54.74 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3, Unless otherwise specified, tolerances are *.005 (0.13 mm) for three place HA .200 MIN Of decimals. FIGURE 1. Case outlines. STANDARDIZED A MILITARY DRAWING 3962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 9 DESC FORM 193A SEP 87 @ U. 5. GOVERNMENT PRINTING OFFICE: 1988540-004Case outline Y PIN NO I 050 TYP b_ ost .002 TYP | so ah 1.015 Lace MIN MAX MIN 050 #0057 | a _ O10 +.002 TYP 125 MAX -~ Inches mn 1.590 40.39 1.450 36.83 1.015 25.78 350 8.89 125 3.18 . 050 1.27 .O15 38 -005 13 -002 08 NUTES: 1. Dimensions are in inches. Zz. Metric equivalents are given for general information only. FIGURE 1. Case outlines - Continued. STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL DAYTON, OHIO 45444 SHEET 10 DESC FORM 193A SEP 87 2U S$ GOVERNMENT PRINTING OFFICE: 12a8--449-004r rt rT ! | ! Device type ! All ! All ! Device type ! AY] | Al | rT | Case outline X Y ! Case outline | X | Y | T rT : | | Terminal | Terminal i Tenninal i 1 Terminal | Terminal | Tenninal | number symbol | symbol] |! | number symbo | ! symbol | | I T TT I | | 1 IVec INC | | 31 IDSC OUT INC | | 2 [Dg LOAD DATA 1 =| | 32 |RT ENABLE [DATA OUT i | 3 IDg 1043 1] 33 IDEC RST [DATA OUT | 4 Dig iDrg 1 | 34 |GROUAD [SEND DATA | | 5 IDy) IDis 1) 35 OUTPUT INH |ESC OUT | | 6 IDy> Icc i | 36 |SERIAL DATA OUTIXTAL | | 7 [DATA SELECT I [Dg 1 | 37 [TAKE DATA [*5V(OSC/CLOCK) | | 8 lA3 IDg I | 38 IMRST IDSC OUT i | 9 |Ap ID19 | 39 |BROADCAST IRT ENABLE | i 10 |Ay ID) 1 | 40 |MODE CODE [DEC RST I | 11 | GROUND IDy2 it 41 Dg ~ }GROUND I | 12 |Ag IDATA SELECT I | | 42 \D7 (OUTPUT INH | | 13 IAy 1A3 1 | 43 [DATA SELECT 2 SERIAL DATA OUT| | 14 | VALTO WORD lAp 1 | 44 IDs I TAKE DATA | | 15 IFAIL SAFE 1A; I 45 IDp [MRST | | 16 ICOMM/DATA SYNC |GROUND | 46 1D, IBROADCAST | 17 |CLOCK IN IAg it 47 ID [MODE CODE | | 18 ICLOCK OUT 1Ag rl 48 103 ID | 19 IS/T SELECT |VALTD WORD 1 | 49 ILATCH DATA 2. |Dy | | 20 [CASE IFAIL SAFE 1 | 50 IDy [DATA SELECT 2 | | 21 IDATA_IN ICOMM/DATA SYNC | | 51 LOAD DATA 2 [Dg | | 22 IDATA_IN |CLOCK IN | 52 ILATCH DATA 1 Dp | | 23 [ENC ENA ICLOCK OUT 1 | 53 [LOAD DATA 1 = 1D, | | 24 ISYNC SEL IS/T SELECT 1] 54 1D 43 ID, l | 25 IDATA OUT ICASE 1] 55 IDyg ID3 | | 26 IDATA OUT IDATA_IN I | 56 IDy5 ILATCH DATA 2 | | 27 |SEND DATA IDATA_IN 1 | 57 | ooo IDy | | 28 JESC OUT JENC ENA 1 | 58 | o--- |LOAD DATA 2 | 29 | XTAL ISYNC SEL 1] 59 | <--> ILATCH DATA 1 | | 30 1*5V(OSC/CLOCK) INC I | 60 ---- INC | | | | i | | | | FIGURE 2, Terminal connections. STANDARDIZED SIZE MILITARY DRAWING A 5962-20636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 1 DESC FORM 193A SEP 37 U. $. GOVERNMENT PRINTING OFFICE: 1980- 549-004__ weabelp x501g auNnT4 o NI 49079 OQww wm) LNO 9079 Yu BAIN Lf 1n0 980 oO 43019 oo C) WWLX 9 3asvo WivO gyvL an eet O--~ : Oa _Y3MOd_49079/ 1SO_A St 280 ano = _. 188930 ST QNAS VLVO/WW0D oe tintin 10 __ 10%" Ow 2 NSONS OND n] 790230 QITvA aS ONAS A S+ 5 yy 300W 3009 Om" Td 9S 3 oo ? 300" Owe IDA vivd ON3S~.. ~ 104 1NOD t > ne | om ___() 8 YaVNL -ovoua}| 1S9 34VS WV gays tvs -avoue inO viva : | 31907 31907 ? --F) \ 1081 yO9 OYLNOD yado09 Ov (Hs?) ino viva @ y3000Na | 8 4u3000R0 -3q | ive OQa 5 YALISSHINVAW] YALSIHONVAN $s3y0 ze 19373S 1/5 ea e ~av [Gy OQ-] ed Lamp oO Ni viva wna | pu(asw) NI viva 31avN3 LU | - oas a S10-8d sid-9a -~| sid-sa sia -80 934 93u 939 [AlLiL_} 938 LWx LWX Ki n.o3y KT] A3e wNVA | NWS NYY yNVY aN2 | 4s! aNz 1st _,!| 40-00 20-00 20-00 20-00 934 | 9ay 93y 93u LWX 4 inx [1 A,938 KC A,034 NYY wnva PN YNYY NVM | ONd | LSt VIVfojo jojo jololgjo|yu/ cjojojq 9 GNZ isl o|T I. BIB lara Jo lo M] @] AIO [EY SB] [ra] ] el, ged eedesl Ped wel] sale t PIO a|5])9 4340 55 20000000 ms ae _ PIO Po Peo => = Mp mip _t x = roo oO nN my wn vi ~ + cw g ~~ N yoayv LIg- S 12 SHEET 5962-90636 REVISION LEVEL SIZE DAYTON, OHIO 45444 DESC FORM 193A SEP 87 STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER aU S GOVERNMENT PRINTING OFFICE. 1988549-904ENCOCER TIMING | o |i |e | | tae! fart lea t 3 SYNC 2 _ SELECT \\\\\ AX XA h tes SENO DATA | & LOAD DATA TUF used) DOW NR ENCODER | | | | | } | | SHIFT CLOCK ' | jee b ENCODER ~ | pI I ENABLE t- te (SEE NOTE) leg ANN le? I PARALLEL teg te) (SEE NOTE) oaTa IN AAA jerge EIO NOTE: FIGURE 4, Timing diagrams. ste (QQ RR be te tey2 and te13 apply only when LATCH DATA is not used. DAYTON, OHIO 45444 STANDARDIZED SIZE MILITARY DRAWING A 6962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET 13 DESC FORM 193A SEP 87 2 U.S. GOVERNMENT PRINTING OFFICE. 1966548-904DECODER TIMING DECODER | | | | 8 | | | sueteox LT LJ Lf Lf LS o tom t mm | ol 02 =| DATA _ to3 LAST STATEX NEW SYNC waon LAST STATE BROADCAST RT ENABLE le la lne MODE CODE 08 para Le e| ts panac ver KUM KET DATA OUT FIGURE 4. Timing diagrams ~ Continued. STANDARDIZED - MILITARY DRAWING 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET , DAYTON, OHIO 45444 DESC FORM 193A SEP 87 + U. 3 GOVERNMENT PRINTING OFFICE: 1968-~-540-004TABLE II, Electrical test requirements. MIL-STD-883 test requirements Subgroups (per method 5008, group A test table) Interim electrical parameters Final electrical test parameters 1*,2,3,7,9 Group A test requirements 1,2,3,7,8A, 8B ,9,10,11 Group C end-point electrical 1,2,3,7,9 parameters MIL-STD-883 test requirements Subgroups (per method 5005, table I) Group E end-point electrical parameters fe | | | i | | | I | r | | ! | | T | | | | | | *PDA applies to subgroup 1, 4.2 Screening. Screening shal] be in accordance with MIL-H-38534 and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883, (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.7 herein). (2) Te as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with MIL-H-38552 and as specified herein. 4.3.1 Group A inspection. Group A inspection shall be in accordance with MIL-H-38534 and as follows: a. Tests shall be as specified in table II herein, b. Subgroups 4, 5, and 6 in table X, method 5008 of MIL-STD-883 shall be omitted. . Subgroups 7, 8A, and 8B tests shall consist of verifying the functionality of the device. It forms a part of the vendors test tape and shall be maintained and available from the approved source of supply. 4.3.2 Group B inspection. Group 8 inspection shall be in accordance with MIL-H-38534. STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 15 DESC FORM 193A SEP 87 * US GOVERNMENT PRINTING OFFICE 1990-750527R4.3.3 Group C inspection. Group C inspection shall be in accordance with MIL~H-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein, b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.7 herein), (2) 1c as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL -STD-383, 4.3.4 Group D inspection. Group 0 inspection shall be in accordance with MIL-H-38534, 4.3.5 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). RHA levels for device classes H and K shall be M, D, R, and H. RHA quality conformance inspection sample tests shall be performed at the RHA level specified in the acquisition document. a. RHA tests for device classes H and K for levels M, D, R, and H shall be performed through each level to determine at what levels the devices meet the RHA requirements. These RHA tests shall be performed for initial qualification and after design or process changes which may affect the RHA performance of the device. b. End-point electrical parameters shall be as specified in table II herein. c. Prior to total dose irradiation, each selected sample shall be assembled in its qualified package. It shall pass the specified group A electrical Parameters in table I for subgroups specified in table II herein. d. For device classes H and K the devices shal? be subjected to radiation hardness assured tests as specified in MIL-H-38534 for RHA level being tested, and meet the postirradiation end-point electrical parameter limits as defined in table I at Te = +25C 5 percent, after exposure. e. Prior to and during tota) dose irradiation testing, the devices shall be biased to establish a worst case condition as specified in the radiation exposure circuit. f. For device classes H and K, subgroups 1 and 2 in table V, method 5005 of MIL-STD-883 shall be tested as appropriate for device construction. g. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-H~38534, STANDARDIZED SIZE MILITARY DRAWING A 5962-90636 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 16 DESC FORM 193A SEP 87 US GOVERNMENT PRINTING OFFICE +990-750:527A6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for Government microcircults applications (original equipment) design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-STD-481 using DD Form 1693, Engineering Change Proposal (Short Form). 6.4 Record of users. Military and industrial users shall inform Defense Electronics Supply Center when a system application requires configuration control and the applicable SMD. DESC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DESC-ECC, telephone (513) 296-8527. 6.5 Comments. Comments on this drawing should be directed to DESC-ECC, Dayton, Ohio 45444, or telephone (513) 296-8525. 6.6 One part - one part number system. The one part - one part number system described below has been developed to allow for transitions between identical generic devices covered by the four major microcircuit requirements documents (MIL-M-38510, MIL-H-38534, MIL-1-38535, and 1.2.1 of MIL-STD-883) without the necessity for the generation of unique PIN's. The four military requirements documents represent different class levels, and previously when a device manufacturer upgraded military product from one class level to another, the benefits of the upgraded product were unavailable to the Original Equipment Manufacturer (OEM), who was contractually locked into the original unique PIN. By establishing a one part number system covering all four documents, the OEM can acquire to the highest class level available for a given generic device to meet system needs without modifying the original contract parts selection criteria. Example Military documentation format PIN under Manufacturing Document new system source listing listing New MIL-M-38510 Military Detai1 5962-XXXXXZZ(B or S)YY QPL-38510 MIL-BUL-103 Specifications (in the SMD format) (Part 1 or 2) New MIL-H-38534 Standardized Military 5962-XXXXXZZ(H and K)YY QML - 38534 MIL-BUL- 103 Orawings New MIL-I-38535 Standardized Military 5962-XXXXXZZ(Q or V)YY QML - 38535 MIL-BUL~103 Drawings New 1.2.1 of MIL-STD-883 Standardized 962-XXXXXZZ(M)YY MIL-BUL-103 MIL-BUL-103 Military Drawings 6.7 Sources of supply for device classes H and K. Sources of supply for device classes H and K are listed in QML-38534, The vendors listed in QML-38534 have submitted a certificate of compliance {see 3.7 herein) to DESC-ECC and have agreed to this drawing. STANDARDIZED we 5962-90636 MILITARY DRAWING 2-9 DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, OHIO 45444 17 DESC FORM 193A . , SEP 87 US GOVEANMENT PRINTING OFFICE 1990 /50-527ASTANDARDIZED MILITARY DRAWING SOURCE APPROVAL BULLETIN DATE:_ 91-01-28 Approved sources of supply for SMD 5962-90636 are listed below for immediate acquisition only and shall be added to UM.-38534 during the next revision. QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DESC-ECC, This bulletin is superseded by the next dated revision of CHL-38534. l | I | | Standardized | Vendor | Vendor | | military drawing | CAGE | similar | | PIN | number | PIN 1/ | | | I | I T T | | 5962-906 3601HXX 1 32116 | (T1820 | | 5962-9063601HYX ! 32116 CT1820F | ! | { T TT | | 5962-906 3602H XX 1 32116 | CT1820-2 i 1 5962-9063602HYX 32116 | CT1820-2F | | | | I T T | | 5962-9063603HXX | 88379 | ARX2410 | | { | | { T I | | 5962-906 3604HXX | 88379 | ARX3410 | | | | | 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE Vendor name number and address 32116 Marconi Circuit Technology, Inc. 160 Smith Street Farmingdale, NY 11735 88379 Aeroflex Laboratories, Inc. 35 South Service Road Plainview, NY 17803 | the tnformation contained herein is disseminated for convenience only and | | the Government assumes no liability whatsoever for any inaccuracies in this | | information bulletin. |