© Semiconductor Components Industries, LLC, 2006
July, 2006 − Rev. 3 1Publication Order Number:
MUR180E/D
MUR180E, MUR1100E
MUR1100E is a Preferred Device
SWITCHMODEt
Power Rectifiers
Ultrafast “E” Series with High Reverse
Energy Capability
These state−of−the−art devices are designed for use in switching
power supplies, inverters and as free wheeling diodes.
Features
10 mjoules Avalanche Energy Guaranteed
Excellent Protection Against Voltage Transients in Switching
Inductive Load Circuits
Ultrafast 75 Nanosecond Recovery Time
175°C Operating Junction Temperature
Low Forward Voltage
Low Leakage Current
High Temperature Glass Passivated Junction
Reverse Voltage to 1000 V
These are Pb−Free Devices*
Mechanical Characteristics:
Case: Epoxy, Molded
Weight: 0.4 Gram (Approximately)
Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
Shipped in Plastic Bags; 1,000 per Bag
Available Tape and Reel; 5,000 per Reel, by Adding a “RL’ Suffix to
the Part Number
Polarity: Cathode Indicated by Polarity Band
MAXIMUM RATINGS
Rating Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage MUR180E
MUR1100E
VRRM
VRWM
VR800
1000
V
Average Rectified Forward Current (Note 1)
(Square Wave Mounting Method #3 Per Note 3) IF(AV) 1.0 @
TA = 95°CA
Non-Repetitive Peak Surge Current
(Surge applied at rated load conditions,
halfwave, single phase, 60 Hz)
IFSM 35 A
Operating Junction Temperature and Storage
Temperature Range TJ, Tstg 65 to
+175 °C
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
ULTRAFAST RECTIFIERS
1.0 AMPERES, 800−1000 VOLTS
Preferred devices are recommended choices for future use
and best overall value.
http://onsemi.com
PLASTIC
AXIAL LEAD
CASE 59
MARKING DIAGRAM
A = Assembly Location
MUR1x0E = Device Code
x 8 or 10
Y = Year
WW = Work Week
G= Pb−Free Package
(Note: Microdot may be in either location)
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
ORDERING INFORMATION
A
MUR1x0E
YYWW G
G
MUR180E, MUR1100E
http://onsemi.com
2
THERMAL CHARACTERISTICS
Charateristics Symbol Value Unit
Maximum Thermal Resistance, Junction−to−Ambient RqJA See Note 3 °C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 2)
(iF = 1.0 Amp, TJ = 150°C)
(iF = 1.0 Amp, TJ = 25°C)
vF1.50
1.75
V
Maximum Instantaneous Reverse Current (Note 2)
(Rated dc Voltage, TJ = 100°C)
(Rated dc Voltage, TJ = 25°C)
iR600
10
mA
Maximum Reverse Recovery Time
(IF = 1.0 Amp, di/dt = 50 Amp/ms)
(IF = 0.5 Amp, iR = 1.0 Amp, IREC = 0.25 Amp)
trr 100
75
ns
Maximum Forward Recovery Time
(IF = 1.0 Amp, di/dt = 100 Amp/ms, Recovery to 1.0 V) tfr 75 ns
Controlled Avalanche Energy (See Test Circuit in Figure 6) WAVAL 10 mJ
2. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
ORDERING INFORMATION
Device Package Shipping
MUR180E Axial Lead* 1000 Units / Bag
MUR180EG Axial Lead*
MUR180ERL Axial Lead* 5000 / Tape & Reel
MUR180ERLG Axial Lead*
MUR1100E Axial Lead* 1000 Units / Bag
MUR1100EG Axial Lead*
MUR1100ERL Axial Lead* 5000 / Tape & Reel
MUR1100ERLG Axial Lead*
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*These packages are inherently Pb−Free.
MUR180E, MUR1100E
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS
Figure 1. Typical Forward Voltage
vF, INSTANTANEOUS VOLTAGE (VOLTS)
0.3 0.90.5 1.3
3.0
0.01
0.03
0.02
0.2
0.1
20
2.0
0.7
0.3
0.05
0.5
5.0
, INSTANTANEOUS FORWARD CURRENT (AMPS)
F
2.3
VR, REVERSE VOLTAGE (VOLTS)
0 300200 500 600
1000
0.1
0.01
10
100
TJ = 175°C
IR
100 400 1000
Figure 2. Typical Reverse Current*
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
0
1.0
2.0
3.0
4.0
5.0
PF(AV)
0
0.5 1.0 1.5 2.0 2.5
TA, AMBIENT TEMPERATURE (°C)
050
0
2.0
1.0
3.0
5.0
4.0
I
250
Figure 3. Current Derating
(Mounting Method #3 Per Note 3)
Figure 4. Power Dissipation
0
3.0
10
20
2.0
10 20
VR, REVERSE VOLTAGE (VOLTS)
Figure 5. Typical Capacitance
0.7
0.07
1.0
7.0
1.7 2.1
100°C
TJ = 175°C25°C
800 900700
1.0
, REVERSE CURRENT ( A)
100°C
25°C
150100 200
* The curves shown are typical for the highest voltage device in the
grouping. Typical reverse current for lower voltage selections can be
estimated from these same curves if VR is sufficiently below rated VR.
C, CAPACITANCE (pF)
, AVERAGE POWER DISSIPATION (WATTS)
TJ = 25°C
i
, AVERAGE FORWARD CURRENT (AMPS)
F(AV)
30 40 50
7.0
5.0
TJ = 175°C
RATED VR
RqJA = 50°C/W
dc
SQUARE WAVE
m
(CAPACITIVELOAD)
IPK
IAV +20
SQUARE WAVE
dc
5.010
1.1 1.5 1.9
10
MUR180E, MUR1100E
http://onsemi.com
4
MERCURY
SWITCH
VD
ID
DUT
40 mH COIL
+VDD
IL
S1
BVDUT
ILID
VDD
t0t1t2t
Figure 6. Test Circuit Figure 7. Current−Voltage Waveforms
The unclamped inductive switching circuit shown in
Figure 6 was used to demonstrate the controlled avalanche
capability of the new “E’’ series Ultrafast rectifiers. A
mercury switch was used instead of an electronic switch to
simulate a noisy environment when the switch was being
opened.
When S 1 is closed at t0 the current in the inductor IL ramps
up linearly; and energy is stored in the coil. At t1 the switch
is opened and the voltage across the diode under test begins
to rise rapidly, due to di/dt effects, when this induced voltage
reaches the breakdown voltage of the diode, it is clamped a t
BVDUT and the diode begins to conduct the full load current
which now starts to decay linearly through the diode, and
goes to zero at t2.
By solving the loop equation at the point in time when S1
is opened; and calculating the energy that is transferred to
the diode it can be shown that the total energy transferred is
equal to the ener gy stored in the inductor plus a finite amount
of energy from the VDD power supply while the diode is in
breakdown (from t1 to t2) minus any losses due to finite
component resistances. Assuming the component resistive
elements are small Equation (1) approximates the total
energy transferred to the diode. It can be seen from this
equation that if the VDD voltage is low compared to the
breakdown voltage of the device, the amount of energy
contributed by the supply during breakdown is small and the
total energy can be assumed to be nearly equal to the ener gy
stored in the coil during the time when S1 was closed,
Equation (2).
The oscilloscope picture in Figure 8, shows the
information obtained for the MUR8100E (similar die
construction as the MUR1100E Series) in this test circuit
conducting a peak current of one ampere at a breakdown
voltage of 1300 V, and using Equation (2) the energy
absorbed by the MUR8100E is approximately 20 mjoules.
Although it is not recommended to design for this
condition, the new “E’’ series provides added protection
against those unforeseen transient viruses that can produce
unexplained random failures in unfriendly environments.
WAVAL [1
2LI2
LPKǒBVDUT
BVDUT–VDDǓ
WAVAL [1
2LI2
LPK
Figure 8. Current−Voltage Waveforms
CHANNEL 2:
IL
0.5 AMPS/DIV.
CHANNEL 1:
VDUT
500 VOLTS/DIV.
TIME BASE:
20 ms/DIV.
EQUATION (1):
EQUATION (2):
CH1 CH2 REF REF
CH1
CH2
ACQUISITIONS
SAVEREF SOURCE
1 217:33 HRS
STACK
A20ms953 V VERT500V
50mV
MUR180E, MUR1100E
http://onsemi.com
5
Lead Length, L
Mounting
Method 1/8 1/4 1/2 Units
1
2
3
52
67
RqJA
65 72
80 87
50
°C/W
°C/W
°C/W
TYPICAL VALUES FOR RqJA IN STILL AIR
Data shown for thermal resistance, junction−to−ambient
(RqJA) for the mountings shown is to be used as typical
guideline values for preliminary engineering or in case the
tie point temperature cannot be measured.
NOTE 3 — AMBIENT MOUNTING DATA
MOUNTING METHOD 1
MOUNTING METHOD 2
MOUNTING METHOD 3
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
L L
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
L L
Vector Pin Mounting
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
L = 3/8
Board Ground Plane
P.C. Board with
1−1/2 X 1−1/2 Copper Surface
MUR180E, MUR1100E
http://onsemi.com
6
PACKAGE DIMENSIONS
B
D
K
K
F
F
A
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A4.10 5.200.161 0.205
B2.00 2.700.079 0.106
D0.71 0.860.028 0.034
F−−− 1.27−−− 0.050
K25.40 −−−1.000 −−−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO−41 OUTLINE SHALL APPLY
4. POLARITY DENOTED BY CATHODE BAND.
5. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
AXIAL LEAD
CASE 59−10
ISSUE U
POLARITY INDICATOR
OPTIONAL AS NEEDED
(SEE STYLES) STYLE 1:
PIN 1. CATHODE (POLARITY BAND)
2. ANODE
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its of ficers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
MUR180E/D
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative