59628864405TXA - Aeroflex UTMC

Standard Products

UT63M1XX MIL-STD-1553A/B Bus Transceiver

Data Sheet

Sept. 1999

FEATURES

q Full conformance to MIL-STD-1553A and 1553B

q Completely monolithic bipolar technology

q Low power consumption

q Fit and functionally compatible to industry standard 631XX

series

q Idle low encoding version

q Flexible power supply voltages: VCC=+5V, VEE=-12V or -

15V, and VCCA=+5V to +12V or +5V to +15V

q Full military operating temperature range, -55°C to +125°C,

screened to QML Q or QML V requirements

q Standard Military Drawing available

INTRODUCTION

The monolithic UT63M1XX Transceivers are complete

transmitter and receiver pairs conforming fully to MIL-STD-

1553A and 1553B. Encoder and decoder interfaces are idle low.

UTMC’s advanced bipolar technology allows the positive

analog power to range from +5V to +12V or +5V to +15V,

providing more flexibility in system power supply design.

The receiver section of the UT63M1XX series accepts biphase-

modulated Manchester II bipolar data from a MIL-STD-1553

data bus and produces TTL-level signal data at its RXOUT and

RXOUT outputs. An external RXEN input enables or disables

the receiver outputs.

TXIN

RXOUT

RXEN

FROM ENCODER

TO DECODER

DRIVERS

COMPARE

FILTER

LIMITER

and

FILTER

TXIHB

Figure 1. Functional Block Diagram

RXIN

TXOUT

RXIN

TXOUT

RXOUT

TXIN

THRESHOLD

REFERENCE

Legend for TYPE field:

TI = TTL input

TO = TTL output

DO = Differential output

DI = Differential input

() = Channel designator

TRANSMITTER

NAME PACKAGE PIN TYPE DESCRIPTION

SINGLE DUAL

TXOUT

(A) 1 1 DO Transmitter outputs: TXOUT and TXOUT are differential data signals.

TXOUT

(B) N/A 10 DO

TXOUT

(A) 2 2 DO TXOUT is the complement of TXOUT.

TXOUT

(B) N/A 11 DO

TXIHB

(A) 21 34 TI Transmitter inhibit: this is an active high input signal.

TXINB

(B) N/A 25 TI

TXIN

(A) 22 35 TI Transmitter inputs: TXIN and TXIN are complementary TTL-level

Manchester II encoder inputs.

TXIN

(B) N/A 26 TI

TXIN

(A) 23 36 TI TXIN is the complement of TXIN input.

TXIN

(B) N/A 27 TI

The transmitter section accepts biphase TTL-level signal data

at its TXIN and TXIN and produces MIL-STD-1553 data

signals. The transmitter’s output voltage is typically 42VPP, L-

L. Activating the TXIHB input or setting both data inputs to

the same logic level disables the transmitter.

The UT63M1XX series offers a monolithic transmitter and

receiver packaged in either single channel (24-pin) or dual-

channel (36-pin) configurations designed for use in any MIL-

STD-1553 application.

RECEIVER

NAME PACKAGE PIN TYPE DESCRIPTION

SINGLE DUAL

RXOUT

(A) 7 5 TO Receiver outputs: RXOUT and RXOUT are complementary

Manchester II decoder outputs.

RXOUT

(B) N/A 14 TO

RXOUT

(A) 10 8 TO RXOUT is the complement of RXOUT output

RXOUT

(B) N/A 17 TO

RXEN

(A) 8 6 TI Receiver enable/disable: This is an active high input signal.

RXEN

(B) N/A 15 TI

RXIN

(A) 15 29 DI Receiver inputs: RXIN and RXIN are biphase-modulated Manchester

II bipolar inputs from MIL-STD-1553 data bus.

RXIN

(B) N/A 20 DI

RXIN

(A) 16 30 DI RXIN is the complement of RXIN input.

RXIN

(B) N/A 21 DI

POWER AND GROUND

NAME PACKAGE PIN TYPE DESCRIPTION

SINGLE DUAL

VCC

(A) 20 33 PWR +5VDC power (±10%)

VCC

(B) N/A 24 PWR

VCCA

(A) 13 28 PWR +5 to +12VDC power or

+5 to +15VDC power (± 5%)

VCCA

(B) N/A 19 PWR

VEE

(A) 19 32 PWR -12 or -15VDC power (± 5%)

Recommended de-coupling capacitors 4.7µF and.1µF

VEE

(B) N/A 23 PWR

GND

(A) 3, 9, 18 3, 7, 31 GND Ground reference

GND

(B) N/A 12, 16, 22 GND

RXEN

RXOUT

TXOUT

RXIN

TXIN

1312

GND

CHANNEL

Figure 2a. Functional Pin Diagram--Single Channel

TXIHB

TXOUT

RXOUT

TXIN

RXIN

VCCA

VCC

VEE

RXIN

TXIN

RXIN

TXIN

TXOUT

RXOUT

RXEN

TXOUT 36

CHANNEL

GND

TXIHB

Figure 2b. Functional Pin Diagram--Dual Channel

TXOUT

RXOUT

TXIN

RXIN

TXOUT

RXIN

TXIN

RXOUT

VCCA

VCC

VEE

VCC

VEE

TRANSMITTER

The transmitter section accepts Manchester II biphase TTL data

and converts this data into differential phase-modulated current

drive. Transmitter current drivers are coupled to a MIL-STD-

1553 data bus via a transformer driven from the TXOUT and

TXOUT terminals. Transmitter output terminals’ non-

transmitting state is enabled by asserting TXIHB (logic 1), or

by placing both TXIN and TXIN at the same logic level. Table

1, Transmit Operating Mode, lists the functions for the output

data in reference to the state of TXIHB. Figure 3 shows typical

transmitter waveforms.

RECEIVER

The receiver section accepts biphase differential data from a

MIL-STD-1553 data bus at its RXIN and RXIN inputs. The

receiver converts input data to biphase Manchester II TTL

format and is available for decoding at the RXOUT and RXOUT

terminals. The outputs RXOUT and RXOUT represent positive

and negative excursions (respectively) of the inputs RXIN and

RXIN. Figure 4 shows typical receiver output waveforms.

Models UT63M105, UT63M107, UT63M125, and UT63M127

idle in the “0” state when disabled or receiving no signal.

POWER SUPPLY VOLTAGES

The UT63M1XX series meets device requirements over a wide

range of power supply voltages. Table 2 shows the overall

capabilities of all available devices. Each channel of the dual

transceiver is electrically and physically separate from the other

and fully independent, including all power and signal lines. Thus

there will be no interaction between the channels.

Notes:

1. x = Don’t care.

2. Transmitter output terminals are in the non-transmitting mode during Off

time.

3. Transmitter output terminals are in the non-transmitting mode during Off

time, independent of TXIHB status.

Table 1. Transmit Operating Mode

TXIN TXIN TXIHB TXOUT

x1x 1 Off 2

00xOff 3

010On

100On

11xOff 3

TXIN

Figure 3. Typical Transmitter Waveforms

TXIN

tTXDD

90%

10%

TXOUT, TXOUT

TXIN

LINE-TO-LINE

DIFFERENTIAL

OUTPUT

TXIN

TXIHB

BOTH HIGH

BOTH LOW

DATA BUS INTERFACE

The designer can connect the UT63M1XX to the data bus via a

short-stub (direct-coupling) connection or a long-stub

(transformer-coupling) connection. Use a short-stub connection

when the distance from the isolation transformer to the data bus

does not exceed a one-foot maximum. Use a long-stub

connection when the distance from the isolation transformer

exceeds the one-foot maximum and is less than twenty-five feet.

Figure 5 shows various examples of bus coupling

configurations. The UT63M1XX series transceivers are

designed to function with MIL-STD-1553A and 1553B

compatible transformers.

RECOMMENDED THERMAL PROTECTION

All packages, single and dual, should mount to or contact a heat

removal rail located in the printed circuit board. To insure proper

heat transfer between the package and the heat removal rail, use

a thermally conductive material between the package and the

heat removal rail. Use a material such as Mereco XLN-589 or

equivalent to insure heat transfer between the package and heat

removal rail. Figure 4. Typical Receiver Waveforms

QUIESCENT IDLE LOW

RXOUT

LINE-TO-LINE

DIFFERENTIAL

INPUT

RXOUT

tRXDD

Table 2. Transceiver Model Capabilities

MODEL VCC VEE VCCA IDLE

UT63M105 +5V -15V +5 to +15V Low

UT63M107 +5V -12V +5 to +12V Low

UT63M125 +5V -15V +5 to +15V Low

UT63M127 +5V -12V +5 to +12V Low

20 FT MAX

Figure 5. Bus Coupling Configuration

OPERATION

55 OHMS

1 FT MAX

SHORT-STUB

DIRECT COUPLING

LONG-STUB

TRANSFORMER COUPLING

1:1.4

OPERATION

55 OHMS

1 FT MAX

20 FT MAX

SHORT-STUB

DIRECT COUPLING

LONG-STUB

TRANSFORMER COUPLING

1.4:1

2:1 1:1.4

1.2:1

1.66:1

Note:

ZO defined per MIL-STD-1553B in section 4.5.1.5.2.1.

± 15VDC

± 12VDC

.75ZO

VIN

RL =

55 OHMS

35 OHMS A

2K OHMS

RECEIVER

TRANSMITTER

1:1.4

1.4:1

RXIN

RXEN

TXIN TXOUT

RXOUT

TXIHB

55 OHMS

35 OHMS

Notes:

1. TP = Test point.

2. RL removed for terminal input impedance test.

3. TX and RX tied together.

RXIN

TXIN TXOUT

15pF

VCC

RXOUT

Figure 6. Direct-Coupled Transceiver with Load

VIN

Figure 7. Transformer-Coupled Transceiver with Load

1:1.4

2K OHMS

RECEIVER

TRANSMITTER

55 OHMS

35 OHMS

TXIHB

TXIN

RXEN

TXOUT N:L

L:N

1.4:1 RXIN RXOUT

Notes:

1. TP = Test point.

2. N:L Ratio is dependent on power supply voltage.

3. RL removed for terminal input impedance test.

4. TX and RX tied together.

RXIN

TXIN TXOUT

RXOUT

15pF

ABSOLUTE MAXIMUM RATINGS1

(Referenced to VSS)

RECOMMENDED OPERATING CONDITIONS

SYMBOL PARAMETER LIMITS UNIT

VCC Supply Voltage 7.0 V

VEE Supply Voltage -22 V

VCCA Supply Voltage +22 V

VIN Input Voltage Range (Receiver) 42 VPP, L-L

VIN Logic Input Voltage -0.3 to +5.5 V

IOOutput Current (Transmitter) 190 mA

PDPower Dissipation (per Channel) 4W

QJC Thermal Impedance, Junction-to-Case 62°C/W

TJOperating Temperature, Junction -55 to +150 °C

TCOperating Temperature, Case -55 to +125 °C

TSTG Storage Temperature -65 to +150 °C

Notes:

1. Stress outside the listed absolute maximum rating may cause permanent damage to the devices. This is a stress rating only, and functional operation of the

device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

2. Mounting per MIL-STD-883, Method 1012.

PARAMETER LIMITS UNIT

Logic input voltage range 0 to +5.0 V

Receiver differential voltage 9.0 VP-P

Driver peak output current 180 mA

Serial data rate 0.1 to 1 MHz

Case operating temperature range (TC)-55 to +125 °C

TERMINAL

TXOUT

Figure 8. Transceiver Test Circuit MIL-STD-1553B

Notes:

Transformer-Coupled Stub:

Terminal is defined as transceiver plus isolation transformer. Point A defined in figure 7.

Direct-Coupled Stub:

Terminal is defined as transceiver plus isolation transformer and fault resistors. Point A defined in figure 6.

TXOUT

DC ELECTRICAL CHARACTERISTICS

VCC = +5V (± 10%)

VCCA = +5V to + 12V (± 5%) or +5V to +15V (± 5%)

VEE = -12V or -15V (± 5%)

-55°C < TC < +125°C

SYMBOL PARAMETER MINIMUM MAXIMUM UNIT CONDITION

VIL Input Low Voltage 0.8 VRXEN, TXIHB, TXIN, TXIN

VIH Input High Voltage 2.0 VRXEN, TXIHB, TXIN, TXIN

IIL Input Low Current -1.6 mA VIL = 0.4V; RXEN, TXIHB, TXIN,

TXIN

IIH Input High Current 40 µAVIL = 2.4V; RXEN, TXIHB, TXIN,

TXIN

VOL Output Low Voltage 0.55 VIOL = 4.0 mA; RXOUT, RXOUT

VOH Output High Voltage 2.4 VIOH = 0.4 mA; RXOUT, RXOUT

ICC VCC Supply Current

VEE = -12V VCC = 5V

VCCA = +5V to +12V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

VEE = -15V VCC = 5V

VCCA = +5V to +15V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

ICCA VCCA Supply Current

VEE = -12V VCC = 5V

VCCA = +5V to +12V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

VEE = -15V VCC = 5V

VCCA = +5V to +15V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

IEE VEE Supply Current

140

230

130

230

VEE = -12V VCC = 5V

VCCA = +5V to +12V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

VEE = -15V VCC = 5V

VCCA = +5V to +15V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

PCD Power Dissipation

0.9

2.1

3.3

1.0

2.5

3.8

VEE = -12V VCC = 5V

VCCA = +5V to +12V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

VEE = -15V VCC = 5V

VCCA = +5V to +15V

0% duty cycle (non-transmitting)

50% duty cycle (ƒ = 1MHz)

100% duty cycle (ƒ = 1MHz)

Notes:

1. All tests guaranteed per test figure 6.

2. As specified in test conditions.

DC ELECTRICAL CHARACTERISTICS

VCC = +5V (± 10%)

VCCA = +5V to + 12V (± 5%) or +5V to +15V (± 5%)

VEE = -12V or -15V (± 5%)

-55°C < TC < +125°C

SYMBOL PARAMETER MINIMUM MAXIMUM UNIT CONDITION

RECEIVER ELECTRICAL CHARACTERISTICS 1

VCC = +5V (± 10%)

VCCA = +5V to + 12V (± 5%) or +5V to +15V (± 5%)

VEE = -12V or -15V (± 5%)

-55°C < TC < +125°C

SYMBOL PARAMETER MINIMUM MAXIMUM UNIT CONDITION

RIZ2Differential (Receiver)

Input Impedance 15 K Ohms Input ƒ = 1MHz (no transformer

in circuit)

CIN2Input Capacitance 10 pF RXEN; input ƒ = 1MHz @ 0V

VIC2Common Mode Input Volt-

age -10 +10 VDirect-coupled stub: input

1.2VPP, 200ns rise/fall time ±

25ns, ƒ = 1MHz.

VTH Input Threshold Voltage

(No Response)2

Input Threshold Voltage

(No Response)

Input Threshold Voltage

(Response)2

Input Threshold Voltage

(Response)

0.86

1.20

0.20

0.28

14.0

20.02

VPP,L-L

Transformer-coupled stub: input

at ƒ = 1MHz, rise/fall time 200ns

at (Receiver output 0 → 1

transition).

Direct-coupled stub: input at ƒ =

1MHz, rise/fall time 200ns at

(Receiver output 0 → 1

transition).

Transformer-coupled stub: input

at ƒ = 1MHz, rise/fall time 200ns

output at (Receiver output 0 → 1

transition).

Direct-coupled stub: input at ƒ =

1MHz, rise/fall time 200ns output

at (Receiver output 0 → 1

transition).

CMMR2Common Mode Rejection

Ratio Pass/Fail3N/A

Notes:

1. All tests guaranteed per test figure 6.

2. Guaranteed by device characterization.

3. Pass/fail criteria per the test method described in MIL-HDBK-1553 Appendix A, RT Validation Test Plan, Section 5.1.2.2, Common Mode Rejection.

TRANSMITTER ELECTRICAL CHARACTERISTICS1

VCC = +5V (± 10%)

VCCA = +5V to + 12V (± 5%) or +5V to +15V (± 5%)

VEE = -12V or -15V (± 5%)

-55°C < TC < +125°C

SYMBOL PARAMETER MINIMUM MAXIMUM UNIT CONITION

VOOutput Voltage Swing per

MIL-STD-1553B 2

(See figure 9)

per MIL-STD-1553B

(See figure 9)

per MIL-STD-1553A 2

(See figure 9)

VPP, L-L

Transformer-coupled stub, Figure

8, Point A: input ƒ = 1MHz,

RL = 70 ohms.

Direct-coupled stub, Figure 8,

Point A: input ƒ = 1MHz,

RL = 35 ohms.

Figure 7, Point A:

input ƒ = 1MHz, RL = 35 ohms.

VNS 2Output Noise

Voltage Differential

(See figure 9)

mV-RMS,

L-L

mV-RMS,

L-L

Transformer-coupled stub, Figure

8, Point A: input ƒ = DC to 10MHz,

RL = 70 ohms.

Direct-coupled stub, Figure 8,

Point A: input ƒ = DC to 10MHz,

RL = 35 ohms.

Output Symmetry

(See figure 9) -250

-90

+250

+90

mVPP, L-L

Transformer-coupled stub, Figure

8, Point A: RL = 70 ohms, measure-

ment taken 2.5µs after end of trans-

mission

Direct-coupled stub, Figure 8,

Point A: RL = 35 ohms, measure-

ment taken 2.5µs after end of trans-

mission

Output voltage distortion

(overshoot or ring)

(See figure 9)

-900

-300

+900

+300

mV peak,

L-L

mV peak,

L-L

Transformer-coupled stub, Figure

8, Point A: RL = 70 ohms.

Direct-coupled stub, Figure 8,

Point A: RL = 35 ohms.

CIN 2Input Capacitance 10 pF TXIHB, TXIN, TXIN; input

ƒ = 1MHz @ 0 V

Terminal Input Impedance 1

Kohm

Transformer-coupled stub, Figure

7, Point A: input ƒ = 75KHz to

1MHz (power on or power off: non-

transmitting, RL removed from

circuit).

Direct-coupled stub, Figure 6,

Point A: input ƒ = 75KHz to 1MHz

(power on or power off: non-trans-

mitting, RL removed from circuit).

Notes:

1. All tests guaranteed per test figure 6.

2. Guaranteed by device characterization.

VOS 2

TIZ 2

VDIS 2

AC ELECTRICAL CHARACTERISTICS 1

VCC = +5V (± 10%)

VCCA = +5V to + 12V (± 5%) or +5V to +15V (± 5%)

VEE = -12V or -15V (± 5%)

-55°C < TC < +125°C

SYMBOL PARAMETER MINIMUM MAXIMUM UNIT CONDITION

Transmitter Output

Rise/Fall Time

(See figure 10)

100 300 ns Input ƒ = 1MHz 50% duty cycle:

direct-coupled RL = 35 ohms output at

10% through 90% points TXOUT,

TXOUT. Figure 3.

tRXDD RXOUT Delay -200 +200 ns RXOUT to RXOUT; Figure 4.

tTXDD 3 TXIN Skew -25 +25 ns TXIN to TXIN; Figure 4.

tRZCD

Zero Crossing -150 +150 ns Direct-coupled stub; input ƒ = 1MHz,

3VPP (skew INPUT ± 150ns), rise/fall

time 200ns.

tTZCS2

Zero Crossing

Stability

(See figure 10)

-25 +25 ns Input TXIN and TXIN should create

transmitter output zero crossings at

500ns, 1000ns, 1500ns, and 2000ns.

These zero crossings should not devi-

ate more than ± 25ns.

tDXOFF3,4 Transmitter Off;

Delay from Inhibit

Active

400 ns TXIN and TXIN toggling @ 1MHz;

TXIHB transitions from logic zero to

one.

tDXON3,5 Transmitter On;

Delay from Inhibit

Inactive

250 ns TXIN and TXIN toggling @ 1MHz;

TXIHB transitions from logic one to

zero.

Notes:

1. All tests guaranteed per test figure 6.

2. Guaranteed by device characterization.

3. Supplied as a design limit but not guaranteed or tested.

4. Delay time from transmit inhibit (1.5V) to transmit off (280mV).

5. Delay time from not transmit inhibit (1.5V) to transmit on (1.2V).

Table 3. Transformer Requirements Versus Power Supplies

COUPLING TECHNIQUE ± 12VDC ± 15VDC

DIRECT-COUPLED:

Isolation Transformer Ratio 1.2:1 1.4:1

TRANSFORMER-COUPLED:

Isolation Transformer Ratio 1.66:1 2:1

Coupling Transformer Ratio 1:1.4 1:1.4

tR, tF

Figure 10. Transmitter Output Zero Crossing Stability (tTZCS, tR, tF)

Figure 9. Transmitter Output Characteristics (VDIS, VNS, VO)

VDIS (Overshoot)

(Ring) VDIS

Zero Crossing

Stability ± 25ns

Figure 11. Receiver Input Zero Crossing Distortion (tRZCD)

Zero Crossing

Distortion ± 150ns

0 Volts VO

VIN

0 Volts

tTZCS

tRZCD

90%

10%10%

90%

VNS

Figure 12. 36-Pin Side-Brazed DIP, Dual Cavity

Notes:

1.Package material: opaque ceramic.

2.All package finishes are per MIL-PRF-38535.

3.It is recommended that package ceramic be mounted on a heat removal

rail in the printed circuit board. A thermally conductive material should

be used.

LEAD 1

INDICATOR

0.005 MIN.

.610 MAX.

.570 MIN.

.015 MAX.

.008 MIN.

.620 MAX

.590 MIN.

(AT SEATING PLANE)

1.89 MAX

0.001 MIN.

.023 MAX.

.014 MIN.

0.155

MAX. 0.150

MIN.

0.100

Notes:

1.All package finishes are per MIL-M-38510.

2.It is recommended that package ceramic be mounted on a heat removal

rail in the printed circuit board. A thermally conductive material such as

MERECO XLN-589 or equivalent should be used.

3. Letter designations are for cross-reference to MIL-M-38510.

Figure 13. 24-Pin Side-Brazed DIP, Single Cavity

Notes:

1.All package finishes are per MIL-M-38510.

2.It is recommended that package ceramic be mounted on a heat removal

rail in the printed circuit board. A thermally conductive material such as

MERECO XLN-589 or equivalent should be used.

3. Letter designations are for cross-refernce to MIL-M-38510.

Figure 14. 36-Pin Lead Flatpack

(100-MIL Lead Spacing)

Figure 15. 36-Lead Flatpack, Dual Cavity

(50-Mil Lead Spacing)

Notes:

1.Package material: opaque ceramic.

2.All package plating finishes are per MIL-M-38510.

3.Lid is not connected to any electrical potential.

4.It is recommended that package ceramic be mounted to a heat removal rail located in the

printed circuit board. A thermally conductive material such as Mereco XLN-589 or

equivalent should be used.

1.00+.025

0.700±0.015 L

LEAD 1 INDICATOR

0.130 MAX.

0.070±0.010

(AT CERAMIC BODY)

D-

.050

0.016±.002

0.007 -0.001

+0.002

ORDERING INFORMATION

UT63M Single Channel MIL-STD-1553 Monolithic Transceiver: SM

Lead Finish:

(A) = Solder

(X) =Optional

Case Outline:

(U) =24 pin DIP

Class Designator:

(-) =Bland or No field is QML Q

(Q) =QML

Device Type

(01) =+\-15V, idle low

(02) =+\-12V, Idle low

Drawing Number: 88644

Total Dose: None

(R) =1E5 (100KRad)

Federal Stock Class Designator: No options

5962 * * * * * *

Notes:

1. Lead finish (A, C, or X) must be specified.

2. If an “X” is specified when ordering, part marking will match the lead finish and will be either “A” (solder) or “C” (gold).

3. RadHard offered only on 01 device type. Cobalt 60testing required.

4. For QML Q product, the Q designator is intentionally left blank in the SMD number (e.g. 5962-8864401UX).

UT63M Single Channel MIL-STD-1553 Monolithic Transceiver

Radiation:

5 = 1E5 rads(Si)

- = None

Lead Finish:

(A) =Solder

(X) =Optional

Screening:

(P) =Prototype

(Q) = QML-Q

(V) = QML-V

Package Type:

(P) =24-pin DIP

Device Type Modifier:

105 = +\-15V, Idle low

107 = +\- 12V, Idle Low

UT63M * * * * *

Notes:

1. Lead finish (A, C, or X) must be specified.

2. If an “X” is specified when ordering, part marking will match the lead finish and will be either “A” (solder) or “C” (gold).

3. Military Temperature range devices are burned-in and are tested at -55°C, room temperature, and 125°C. Radiation characteristics are neither tested

nor guaranteed and may not be specified.

4. Devices have prototype assembly and are tested at 25°C only. Radiation characteristics are neither tested nor guaranteed and may not be specified. Lead

finish is at UTMC’s option and an “X” must be specified when ordering.

5. The 63M105 only may be ordered with 1E5 rads(Si) total dose. Co60 testing is required. Contact factory for details.

6. SEU and neutron irradiation limits will be added when available.

Appendix 1 - 22

ORDERING INFORMATION

UT63M Dual Monolithic Transceiver: SMD

Lead Finish:

(A) = Solder

(X) =Optional

Case Outline:

(X) =36 pin DIP

(Y) =36 pin FP (.100)

(Z ) =36 pin FP (.50)

Class Designator:

(-) =Blank orNo field is QML Q

(V) =QML V

Device Type

(05) =+\-15V, idle low

(06) =+\-12V, Idle low

Drawing Number: 88644

(-) =None

(R) =1E5 (100Krad)

Federal Stock Class Designator: No options

5962 * * * * *

Notes:

1. Lead finish (A, C, or X) must be specified.

2. If an “X” is specified when ordering, part marking will match the lead finish and will be either “A” (solder) or “C” (gold).

3. RadHard offered only on 05 device type. Cobalt 60testing required.

4. For QML Q product, the Q designator is intentionally left blank in the SMD number (e.g. 5962-8864405YX).

UT63M Dual Multichip Monolithic Transceiver

Radiation:

None

Lead Finish:

(A) =Solder

(X) =Optional

Screening:

(P) =Prototype

(Q) = QML-Q

(V) = QML-V

Package Type:

(B) =36-pin DIP

(D) =36-pin FP (.100)

Device Type Modifier:

125 = +\-15V, Idle low

127 = +\- 12V, Idle Low

UT63M- * * * *

Notes:

1. Lead finish (A, C, or X) must be specified.

2. If an “X” is specified when ordering, part marking will match the lead finish and will be either “A” (solder) or “C” (gold).

3. Military Temperature range devices are burned-in and tested at -55°C, room temperature, and 125°C. Radiation characteristics are neither tested nor

guaranteed and may not be specified.

4. Devices have prototype assembly and are tested at 25°C only. Radiation characteristics are neither tested nor guaranteed and may not be specified. Lead

finish is GOLD only.